This driver supports the on-chip 1/10Gbit Ethernet controller on
PA Semi's PWRficient line of chips.
-config MLX4_EN
- tristate "Mellanox Technologies 10Gbit Ethernet support"
- depends on PCI && INET
- select MLX4_CORE
- select INET_LRO
- help
- This driver supports Mellanox Technologies ConnectX Ethernet
- devices.
-
-config MLX4_CORE
- tristate
- depends on PCI
- default n
-
-config MLX4_DEBUG
- bool "Verbose debugging output" if (MLX4_CORE && EXPERT)
- depends on MLX4_CORE
- default y
- ---help---
- This option causes debugging code to be compiled into the
- mlx4_core driver. The output can be turned on via the
- debug_level module parameter (which can also be set after
- the driver is loaded through sysfs).
-
config TEHUTI
tristate "Tehuti Networks 10G Ethernet"
depends on PCI
obj-$(CONFIG_DM9000) += dm9000.o
obj-$(CONFIG_PASEMI_MAC) += pasemi_mac_driver.o
pasemi_mac_driver-objs := pasemi_mac.o pasemi_mac_ethtool.o
-obj-$(CONFIG_MLX4_CORE) += mlx4/
obj-$(CONFIG_ENC28J60) += enc28j60.o
obj-$(CONFIG_ETHOC) += ethoc.o
obj-$(CONFIG_GRETH) += greth.o
source "drivers/net/ethernet/emulex/Kconfig"
source "drivers/net/ethernet/intel/Kconfig"
source "drivers/net/ethernet/i825xx/Kconfig"
+source "drivers/net/ethernet/mellanox/Kconfig"
source "drivers/net/ethernet/qlogic/Kconfig"
source "drivers/net/ethernet/racal/Kconfig"
source "drivers/net/ethernet/sfc/Kconfig"
obj-$(CONFIG_NET_VENDOR_EMULEX) += emulex/
obj-$(CONFIG_NET_VENDOR_INTEL) += intel/
obj-$(CONFIG_NET_VENDOR_I825XX) += i825xx/
+obj-$(CONFIG_NET_VENDOR_MELLANOX) += mellanox/
obj-$(CONFIG_NET_VENDOR_QLOGIC) += qlogic/
obj-$(CONFIG_NET_VENDOR_RACAL) += racal/
obj-$(CONFIG_SFC) += sfc/
--- /dev/null
+#
+# Mellanox driver configuration
+#
+
+config NET_VENDOR_MELLANOX
+ bool "Mellanox devices"
+ depends on PCI && INET
+ ---help---
+ If you have a network (Ethernet) card belonging to this class, say Y
+ and read the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ Note that the answer to this question doesn't directly affect the
+ kernel: saying N will just cause the configurator to skip all
+ the questions about Mellanox cards. If you say Y, you will be asked
+ for your specific card in the following questions.
+
+if NET_VENDOR_MELLANOX
+
+source "drivers/net/ethernet/mellanox/mlx4/Kconfig"
+
+endif # NET_VENDOR_MELLANOX
--- /dev/null
+#
+# Makefile for the Mellanox device drivers.
+#
+
+obj-$(CONFIG_MLX4_CORE) += mlx4/
--- /dev/null
+#
+# Mellanox driver configuration
+#
+
+config MLX4_EN
+ tristate "Mellanox Technologies 10Gbit Ethernet support"
+ depends on PCI && INET
+ select MLX4_CORE
+ select INET_LRO
+ ---help---
+ This driver supports Mellanox Technologies ConnectX Ethernet
+ devices.
+
+config MLX4_CORE
+ tristate
+ depends on PCI
+ default n
+
+config MLX4_DEBUG
+ bool "Verbose debugging output" if (MLX4_CORE && EXPERT)
+ depends on MLX4_CORE
+ default y
+ ---help---
+ This option causes debugging code to be compiled into the
+ mlx4_core driver. The output can be turned on via the
+ debug_level module parameter (which can also be set after
+ the driver is loaded through sysfs).