+++ /dev/null
-/*
- * linux/arch/arm/mach-at91/board-usb-a9260.c
- *
- * Copyright (C) 2005 SAN People
- * Copyright (C) 2006 Atmel
- * Copyright (C) 2007 Calao-systems
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/gpio_keys.h>
-#include <linux/input.h>
-#include <linux/clk.h>
-
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/hardware.h>
-#include <mach/board.h>
-#include <mach/gpio.h>
-#include <mach/at91sam9_smc.h>
-#include <mach/at91_shdwc.h>
-
-#include "sam9_smc.h"
-#include "generic.h"
-
-
-static void __init ek_init_early(void)
-{
- /* Initialize processor: 12.000 MHz crystal */
- at91_initialize(12000000);
-
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
-
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
-}
-
-/*
- * USB Host port
- */
-static struct at91_usbh_data __initdata ek_usbh_data = {
- .ports = 2,
-};
-
-/*
- * USB Device port
- */
-static struct at91_udc_data __initdata ek_udc_data = {
- .vbus_pin = AT91_PIN_PC5,
- .pullup_pin = 0, /* pull-up driven by UDC */
-};
-
-/*
- * MACB Ethernet device
- */
-static struct at91_eth_data __initdata ek_macb_data = {
- .phy_irq_pin = AT91_PIN_PA31,
- .is_rmii = 1,
-};
-
-/*
- * NAND flash
- */
-static struct mtd_partition __initdata ek_nand_partition[] = {
- {
- .name = "Uboot & Kernel",
- .offset = 0,
- .size = SZ_16M,
- },
- {
- .name = "Root FS",
- .offset = MTDPART_OFS_NXTBLK,
- .size = 120 * SZ_1M,
- },
- {
- .name = "FS",
- .offset = MTDPART_OFS_NXTBLK,
- .size = 120 * SZ_1M,
- }
-};
-
-static struct mtd_partition * __init nand_partitions(int size, int *num_partitions)
-{
- *num_partitions = ARRAY_SIZE(ek_nand_partition);
- return ek_nand_partition;
-}
-
-static struct atmel_nand_data __initdata ek_nand_data = {
- .ale = 21,
- .cle = 22,
-// .det_pin = ... not connected
- .rdy_pin = AT91_PIN_PC13,
- .enable_pin = AT91_PIN_PC14,
- .partition_info = nand_partitions,
-};
-
-static struct sam9_smc_config __initdata ek_nand_smc_config = {
- .ncs_read_setup = 0,
- .nrd_setup = 1,
- .ncs_write_setup = 0,
- .nwe_setup = 1,
-
- .ncs_read_pulse = 3,
- .nrd_pulse = 3,
- .ncs_write_pulse = 3,
- .nwe_pulse = 3,
-
- .read_cycle = 5,
- .write_cycle = 5,
-
- .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
- .tdf_cycles = 2,
-};
-
-static void __init ek_add_device_nand(void)
-{
- /* configure chip-select 3 (NAND) */
- sam9_smc_configure(3, &ek_nand_smc_config);
-
- at91_add_device_nand(&ek_nand_data);
-}
-
-/*
- * GPIO Buttons
- */
-
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
-static struct gpio_keys_button ek_buttons[] = {
- { /* USER PUSH BUTTON */
- .code = KEY_ENTER,
- .gpio = AT91_PIN_PB10,
- .active_low = 1,
- .desc = "user_pb",
- .wakeup = 1,
- }
-};
-
-static struct gpio_keys_platform_data ek_button_data = {
- .buttons = ek_buttons,
- .nbuttons = ARRAY_SIZE(ek_buttons),
-};
-
-static struct platform_device ek_button_device = {
- .name = "gpio-keys",
- .id = -1,
- .num_resources = 0,
- .dev = {
- .platform_data = &ek_button_data,
- }
-};
-
-static void __init ek_add_device_buttons(void)
-{
- at91_set_GPIO_periph(AT91_PIN_PB10, 1); /* user push button, pull up enabled */
- at91_set_deglitch(AT91_PIN_PB10, 1);
-
- platform_device_register(&ek_button_device);
-}
-#else
-static void __init ek_add_device_buttons(void) {}
-#endif
-
-/*
- * LEDs
- */
-static struct gpio_led ek_leds[] = {
- { /* user_led (green) */
- .name = "user_led",
- .gpio = AT91_PIN_PB21,
- .active_low = 0,
- .default_trigger = "heartbeat",
- }
-};
-
-static void __init ek_board_init(void)
-{
- /* Serial */
- at91_add_device_serial();
- /* USB Host */
- at91_add_device_usbh(&ek_usbh_data);
- /* USB Device */
- at91_add_device_udc(&ek_udc_data);
- /* NAND */
- ek_add_device_nand();
- /* I2C */
- at91_add_device_i2c(NULL, 0);
- /* Ethernet */
- at91_add_device_eth(&ek_macb_data);
- /* Push Buttons */
- ek_add_device_buttons();
- /* LEDs */
- at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
- /* shutdown controller, wakeup button (5 msec low) */
- at91_sys_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) | AT91_SHDW_WKMODE0_LOW
- | AT91_SHDW_RTTWKEN);
-}
-
-MACHINE_START(USB_A9260, "CALAO USB_A9260")
- /* Maintainer: calao-systems */
- .timer = &at91sam926x_timer,
- .map_io = at91_map_io,
- .init_early = ek_init_early,
- .init_irq = at91_init_irq_default,
- .init_machine = ek_board_init,
-MACHINE_END
/*
- * linux/arch/arm/mach-at91/board-usb-a9263.c
+ * linux/arch/arm/mach-at91/board-usb-a926x.c
*
* Copyright (C) 2005 SAN People
* Copyright (C) 2007 Atmel Corporation.
.pullup_pin = 0, /* pull-up driven by UDC */
};
+void ek_add_device_udc(void)
+{
+ if (machine_is_usb_a9260())
+ ek_udc_data.vbus_pin = AT91_PIN_PC5;
+
+ at91_add_device_udc(&ek_udc_data);
+}
+
/*
* SPI devices.
*/
#endif
};
+void ek_add_device_spi(void)
+{
+ if (machine_is_usb_a9263())
+ at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
+}
+
/*
* MACB Ethernet device
*/
.is_rmii = 1,
};
+void ek_add_device_eth(void)
+{
+ if (machine_is_usb_a9260())
+ ek_macb_data.phy_irq_pin = AT91_PIN_PA31;
+
+ at91_add_device_eth(&ek_macb_data);
+}
+
/*
* NAND flash
*/
static struct mtd_partition __initdata ek_nand_partition[] = {
{
- .name = "Linux Kernel",
+ .name = "Uboot & Kernel",
.offset = 0,
.size = SZ_16M,
},
static void __init ek_add_device_nand(void)
{
+ if (machine_is_usb_a9260()) {
+ ek_nand_data.rdy_pin = AT91_PIN_PC13;
+ ek_nand_data.enable_pin = AT91_PIN_PC14;
+ }
+
/* configure chip-select 3 (NAND) */
sam9_smc_configure(3, &ek_nand_smc_config);
}
};
+void ek_add_device_leds(void)
+{
+ if (machine_is_usb_a9260())
+ ek_leds[0].active_low = 0;
+
+ at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
+}
+
static void __init ek_board_init(void)
{
/* USB Host */
at91_add_device_usbh(&ek_usbh_data);
/* USB Device */
- at91_add_device_udc(&ek_udc_data);
+ ek_add_device_udc();
/* SPI */
- at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
+ ek_add_device_spi();
/* Ethernet */
- at91_add_device_eth(&ek_macb_data);
+ ek_add_device_eth();
/* NAND */
ek_add_device_nand();
/* I2C */
/* Push Buttons */
ek_add_device_buttons();
/* LEDs */
- at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
+ ek_add_device_leds();
/* shutdown controller, wakeup button (5 msec low) */
at91_sys_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) | AT91_SHDW_WKMODE0_LOW
| AT91_SHDW_RTTWKEN);
.init_irq = at91_init_irq_default,
.init_machine = ek_board_init,
MACHINE_END
+
+MACHINE_START(USB_A9260, "CALAO USB_A9260")
+ /* Maintainer: calao-systems */
+ .timer = &at91sam926x_timer,
+ .map_io = at91_map_io,
+ .init_early = ek_init_early,
+ .init_irq = at91_init_irq_default,
+ .init_machine = ek_board_init,
+MACHINE_END
projects / linux-beck.git / commitdiff