/*
* Copyright (c) 2013 Xilinx, Inc.
+ * Copyright (c) 2015 DAVE Embedded Systems
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef _ZYNQ_GPIO_H
#define _ZYNQ_GPIO_H
+#define ZYNQ_GPIO_BASE_ADDRESS 0xE000A000
+
+/* Maximum banks */
+#define ZYNQ_GPIO_MAX_BANK 4
+
+#define ZYNQ_GPIO_BANK0_NGPIO 32
+#define ZYNQ_GPIO_BANK1_NGPIO 22
+#define ZYNQ_GPIO_BANK2_NGPIO 32
+#define ZYNQ_GPIO_BANK3_NGPIO 32
+
+#define ZYNQ_GPIO_NR_GPIOS (ZYNQ_GPIO_BANK0_NGPIO + \
+ ZYNQ_GPIO_BANK1_NGPIO + \
+ ZYNQ_GPIO_BANK2_NGPIO + \
+ ZYNQ_GPIO_BANK3_NGPIO)
+
+#define ZYNQ_GPIO_BANK0_PIN_MIN 0
+#define ZYNQ_GPIO_BANK0_PIN_MAX (ZYNQ_GPIO_BANK0_PIN_MIN + \
+ ZYNQ_GPIO_BANK0_NGPIO - 1)
+#define ZYNQ_GPIO_BANK1_PIN_MIN (ZYNQ_GPIO_BANK0_PIN_MAX + 1)
+#define ZYNQ_GPIO_BANK1_PIN_MAX (ZYNQ_GPIO_BANK1_PIN_MIN + \
+ ZYNQ_GPIO_BANK1_NGPIO - 1)
+#define ZYNQ_GPIO_BANK2_PIN_MIN (ZYNQ_GPIO_BANK1_PIN_MAX + 1)
+#define ZYNQ_GPIO_BANK2_PIN_MAX (ZYNQ_GPIO_BANK2_PIN_MIN + \
+ ZYNQ_GPIO_BANK2_NGPIO - 1)
+#define ZYNQ_GPIO_BANK3_PIN_MIN (ZYNQ_GPIO_BANK2_PIN_MAX + 1)
+#define ZYNQ_GPIO_BANK3_PIN_MAX (ZYNQ_GPIO_BANK3_PIN_MIN + \
+ ZYNQ_GPIO_BANK3_NGPIO - 1)
+
+/* Register offsets for the GPIO device */
+/* LSW Mask & Data -WO */
+#define ZYNQ_GPIO_DATA_LSW_OFFSET(BANK) (0x000 + (8 * BANK))
+/* MSW Mask & Data -WO */
+#define ZYNQ_GPIO_DATA_MSW_OFFSET(BANK) (0x004 + (8 * BANK))
+/* Data Register-RW */
+#define ZYNQ_GPIO_DATA_RO_OFFSET(BANK) (0x060 + (4 * BANK))
+/* Direction mode reg-RW */
+#define ZYNQ_GPIO_DIRM_OFFSET(BANK) (0x204 + (0x40 * BANK))
+/* Output enable reg-RW */
+#define ZYNQ_GPIO_OUTEN_OFFSET(BANK) (0x208 + (0x40 * BANK))
+/* Interrupt mask reg-RO */
+#define ZYNQ_GPIO_INTMASK_OFFSET(BANK) (0x20C + (0x40 * BANK))
+/* Interrupt enable reg-WO */
+#define ZYNQ_GPIO_INTEN_OFFSET(BANK) (0x210 + (0x40 * BANK))
+/* Interrupt disable reg-WO */
+#define ZYNQ_GPIO_INTDIS_OFFSET(BANK) (0x214 + (0x40 * BANK))
+/* Interrupt status reg-RO */
+#define ZYNQ_GPIO_INTSTS_OFFSET(BANK) (0x218 + (0x40 * BANK))
+/* Interrupt type reg-RW */
+#define ZYNQ_GPIO_INTTYPE_OFFSET(BANK) (0x21C + (0x40 * BANK))
+/* Interrupt polarity reg-RW */
+#define ZYNQ_GPIO_INTPOL_OFFSET(BANK) (0x220 + (0x40 * BANK))
+/* Interrupt on any, reg-RW */
+#define ZYNQ_GPIO_INTANY_OFFSET(BANK) (0x224 + (0x40 * BANK))
+
+/* Disable all interrupts mask */
+#define ZYNQ_GPIO_IXR_DISABLE_ALL 0xFFFFFFFF
+
+/* Mid pin number of a bank */
+#define ZYNQ_GPIO_MID_PIN_NUM 16
+
+/* GPIO upper 16 bit mask */
+#define ZYNQ_GPIO_UPPER_MASK 0xFFFF0000
+
+#define BIT(x) (1<<x)
+
#endif /* _ZYNQ_GPIO_H */
--- /dev/null
+/*
+ * Xilinx Zynq GPIO device driver
+ *
+ * Copyright (C) 2015 DAVE Embedded Systems <devel@dave.eu>
+ *
+ * Most of code taken from linux kernel driver (linux/drivers/gpio/gpio-zynq.c)
+ * Copyright (C) 2009 - 2014 Xilinx, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <asm/errno.h>
+
+/**
+ * zynq_gpio_get_bank_pin - Get the bank number and pin number within that bank
+ * for a given pin in the GPIO device
+ * @pin_num: gpio pin number within the device
+ * @bank_num: an output parameter used to return the bank number of the gpio
+ * pin
+ * @bank_pin_num: an output parameter used to return pin number within a bank
+ * for the given gpio pin
+ *
+ * Returns the bank number and pin offset within the bank.
+ */
+static inline void zynq_gpio_get_bank_pin(unsigned int pin_num,
+ unsigned int *bank_num,
+ unsigned int *bank_pin_num)
+{
+ switch (pin_num) {
+ case ZYNQ_GPIO_BANK0_PIN_MIN ... ZYNQ_GPIO_BANK0_PIN_MAX:
+ *bank_num = 0;
+ *bank_pin_num = pin_num;
+ break;
+ case ZYNQ_GPIO_BANK1_PIN_MIN ... ZYNQ_GPIO_BANK1_PIN_MAX:
+ *bank_num = 1;
+ *bank_pin_num = pin_num - ZYNQ_GPIO_BANK1_PIN_MIN;
+ break;
+ case ZYNQ_GPIO_BANK2_PIN_MIN ... ZYNQ_GPIO_BANK2_PIN_MAX:
+ *bank_num = 2;
+ *bank_pin_num = pin_num - ZYNQ_GPIO_BANK2_PIN_MIN;
+ break;
+ case ZYNQ_GPIO_BANK3_PIN_MIN ... ZYNQ_GPIO_BANK3_PIN_MAX:
+ *bank_num = 3;
+ *bank_pin_num = pin_num - ZYNQ_GPIO_BANK3_PIN_MIN;
+ break;
+ default:
+ printf("invalid GPIO pin number: %u\n", pin_num);
+ *bank_num = 0;
+ *bank_pin_num = 0;
+ break;
+ }
+}
+
+int gpio_is_valid(unsigned gpio)
+{
+ return (gpio >= 0) && (gpio < ZYNQ_GPIO_NR_GPIOS);
+}
+
+static int check_gpio(unsigned gpio)
+{
+ if (!gpio_is_valid(gpio)) {
+ printf("ERROR : check_gpio: invalid GPIO %d\n", gpio);
+ return -1;
+ }
+ return 0;
+}
+
+/**
+ * gpio_get_value - Get the state of the specified pin of GPIO device
+ * @gpio: gpio pin number within the device
+ *
+ * This function reads the state of the specified pin of the GPIO device.
+ *
+ * Return: 0 if the pin is low, 1 if pin is high.
+ */
+int gpio_get_value(unsigned gpio)
+{
+ u32 data;
+ unsigned int bank_num, bank_pin_num;
+
+ if (check_gpio(gpio) < 0)
+ return -1;
+
+ zynq_gpio_get_bank_pin(gpio, &bank_num, &bank_pin_num);
+
+ data = readl(ZYNQ_GPIO_BASE_ADDRESS +
+ ZYNQ_GPIO_DATA_RO_OFFSET(bank_num));
+
+ return (data >> bank_pin_num) & 1;
+}
+
+/**
+ * gpio_set_value - Modify the value of the pin with specified value
+ * @gpio: gpio pin number within the device
+ * @value: value used to modify the value of the specified pin
+ *
+ * This function calculates the register offset (i.e to lower 16 bits or
+ * upper 16 bits) based on the given pin number and sets the value of a
+ * gpio pin to the specified value. The value is either 0 or non-zero.
+ */
+int gpio_set_value(unsigned gpio, int value)
+{
+ unsigned int reg_offset, bank_num, bank_pin_num;
+
+ if (check_gpio(gpio) < 0)
+ return -1;
+
+ zynq_gpio_get_bank_pin(gpio, &bank_num, &bank_pin_num);
+
+ if (bank_pin_num >= ZYNQ_GPIO_MID_PIN_NUM) {
+ /* only 16 data bits in bit maskable reg */
+ bank_pin_num -= ZYNQ_GPIO_MID_PIN_NUM;
+ reg_offset = ZYNQ_GPIO_DATA_MSW_OFFSET(bank_num);
+ } else {
+ reg_offset = ZYNQ_GPIO_DATA_LSW_OFFSET(bank_num);
+ }
+
+ /*
+ * get the 32 bit value to be written to the mask/data register where
+ * the upper 16 bits is the mask and lower 16 bits is the data
+ */
+ value = !!value;
+ value = ~(1 << (bank_pin_num + ZYNQ_GPIO_MID_PIN_NUM)) &
+ ((value << bank_pin_num) | ZYNQ_GPIO_UPPER_MASK);
+
+ writel(value, ZYNQ_GPIO_BASE_ADDRESS + reg_offset);
+
+ return 0;
+}
+
+/**
+ * gpio_direction_input - Set the direction of the specified GPIO pin as input
+ * @gpio: gpio pin number within the device
+ *
+ * This function uses the read-modify-write sequence to set the direction of
+ * the gpio pin as input.
+ *
+ * Return: -1 if invalid gpio specified, 0 if successul
+ */
+int gpio_direction_input(unsigned gpio)
+{
+ u32 reg;
+ unsigned int bank_num, bank_pin_num;
+
+ if (check_gpio(gpio) < 0)
+ return -1;
+
+ zynq_gpio_get_bank_pin(gpio, &bank_num, &bank_pin_num);
+
+ /* bank 0 pins 7 and 8 are special and cannot be used as inputs */
+ if (bank_num == 0 && (bank_pin_num == 7 || bank_pin_num == 8))
+ return -1;
+
+ /* clear the bit in direction mode reg to set the pin as input */
+ reg = readl(ZYNQ_GPIO_BASE_ADDRESS + ZYNQ_GPIO_DIRM_OFFSET(bank_num));
+ reg &= ~BIT(bank_pin_num);
+ writel(reg, ZYNQ_GPIO_BASE_ADDRESS + ZYNQ_GPIO_DIRM_OFFSET(bank_num));
+
+ return 0;
+}
+
+/**
+ * gpio_direction_output - Set the direction of the specified GPIO pin as output
+ * @gpio: gpio pin number within the device
+ * @value: value to be written to specified pin
+ *
+ * This function sets the direction of specified GPIO pin as output, configures
+ * the Output Enable register for the pin and uses zynq_gpio_set to set
+ * the value of the pin to the value specified.
+ *
+ * Return: 0 always
+ */
+int gpio_direction_output(unsigned gpio, int value)
+{
+ u32 reg;
+ unsigned int bank_num, bank_pin_num;
+
+ if (check_gpio(gpio) < 0)
+ return -1;
+
+ zynq_gpio_get_bank_pin(gpio, &bank_num, &bank_pin_num);
+
+ /* set the GPIO pin as output */
+ reg = readl(ZYNQ_GPIO_BASE_ADDRESS + ZYNQ_GPIO_DIRM_OFFSET(bank_num));
+ reg |= BIT(bank_pin_num);
+ writel(reg, ZYNQ_GPIO_BASE_ADDRESS + ZYNQ_GPIO_DIRM_OFFSET(bank_num));
+
+ /* configure the output enable reg for the pin */
+ reg = readl(ZYNQ_GPIO_BASE_ADDRESS + ZYNQ_GPIO_OUTEN_OFFSET(bank_num));
+ reg |= BIT(bank_pin_num);
+ writel(reg, ZYNQ_GPIO_BASE_ADDRESS + ZYNQ_GPIO_OUTEN_OFFSET(bank_num));
+
+ /* set the state of the pin */
+ gpio_set_value(gpio, value);
+ return 0;
+}
+
+/**
+ * Request a gpio before using it.
+ *
+ * NOTE: Argument 'label' is unused.
+ */
+int gpio_request(unsigned gpio, const char *label)
+{
+ if (check_gpio(gpio) < 0)
+ return -1;
+
+ return 0;
+}
+
+/**
+ * Reset and free the gpio after using it.
+ */
+int gpio_free(unsigned gpio)
+{
+ return 0;
+}
projects / karo-tx-uboot.git / commitdiff