Required properties:
- compatible: Should be "marvell,mpic"
- interrupt-controller: Identifies the node as an interrupt controller.
+- msi-controller: Identifies the node as an PCI Message Signaled
+ Interrupt controller.
- #interrupt-cells: The number of cells to define the interrupts. Should be 1.
The cell is the IRQ number
#address-cells = <1>;
#size-cells = <1>;
interrupt-controller;
+ msi-controller;
reg = <0xd0020a00 0x1d0>,
<0xd0021070 0x58>;
};
Optional properties:
- interrupts : Interrupt source for parent controllers if the VIC is nested.
+- valid-mask : A one cell big bit mask of valid interrupt sources. Each bit
+ represents single interrupt source, starting from source 0 at LSb and ending
+ at source 31 at MSb. A bit that is set means that the source is wired and
+ clear means otherwise. If unspecified, defaults to all valid.
+- valid-wakeup-mask : A one cell big bit mask of interrupt sources that can be
+ configured as wake up source for the system. Order of bits is the same as for
+ valid-mask property. A set bit means that this interrupt source can be
+ configured as a wake up source for the system. If unspecied, defaults to all
+ interrupt sources configurable as wake up sources.
Example:
interrupt-controller;
#interrupt-cells = <1>;
reg = <0x60000 0x1000>;
+
+ valid-mask = <0xffffff7f>;
+ valid-wakeup-mask = <0x0000ff7f>;
};
-* Gated Clock bindings for Marvell Orion SoCs
+* Gated Clock bindings for Marvell EBU SoCs
-Marvell Dove and Kirkwood allow some peripheral clocks to be gated to save
-some power. The clock consumer should specify the desired clock by having
-the clock ID in its "clocks" phandle cell. The clock ID is directly mapped to
-the corresponding clock gating control bit in HW to ease manual clock lookup
-in datasheet.
+Marvell Armada 370/XP, Dove and Kirkwood allow some peripheral clocks to be
+gated to save some power. The clock consumer should specify the desired clock
+by having the clock ID in its "clocks" phandle cell. The clock ID is directly
+mapped to the corresponding clock gating control bit in HW to ease manual clock
+lookup in datasheet.
The following is a list of provided IDs for Armada 370:
ID Clock Peripheral
Required properties:
- compatible : shall be one of the following:
+ "marvell,armada-370-gating-clock" - for Armada 370 SoC clock gating
+ "marvell,armada-xp-gating-clock" - for Armada XP SoC clock gating
"marvell,dove-gating-clock" - for Dove SoC clock gating
"marvell,kirkwood-gating-clock" - for Kirkwood SoC clock gating
- reg : shall be the register address of the Clock Gating Control register
- compatible: one of the following values:
marvell,armada-370-pcie
marvell,armada-xp-pcie
+ marvell,dove-pcie
marvell,kirkwood-pcie
- #address-cells, set to <3>
- #size-cells, set to <2>
- ranges: ranges describing the MMIO registers to control the PCIe
interfaces, and ranges describing the MBus windows needed to access
the memory and I/O regions of each PCIe interface.
+- msi-parent: Link to the hardware entity that serves as the Message
+ Signaled Interrupt controller for this PCI controller.
The ranges describing the MMIO registers have the following layout:
- marvell,pcie-lane: the physical PCIe lane number, for ports having
multiple lanes. If this property is not found, we assume that the
value is 0.
+- reset-gpios: optional gpio to PERST#
+- reset-delay-us: delay in us to wait after reset de-assertion
Example:
#size-cells = <2>;
bus-range = <0x00 0xff>;
+ msi-parent = <&mpic>;
ranges =
<0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000 /* Port 0.0 registers */
interrupt-map = <0 0 0 0 &mpic 58>;
marvell,pcie-port = <0>;
marvell,pcie-lane = <0>;
+ /* low-active PERST# reset on GPIO 25 */
+ reset-gpios = <&gpio0 25 1>;
+ /* wait 20ms for device settle after reset deassertion */
+ reset-delay-us = <20000>;
clocks = <&gateclk 5>;
status = "disabled";
};
Example:
usb_per5@a03e0000 {
- compatible = "stericsson,db8500-musb", "mentor,musb";
+ compatible = "stericsson,db8500-musb";
reg = <0xa03e0000 0x10000>;
interrupts = <0 23 0x4>;
interrupt-names = "mc";
F: drivers/net/ethernet/seeq/ether3*
F: drivers/scsi/arm/
-ARM/SHARK MACHINE SUPPORT
-M: Alexander Schulz <alex@shark-linux.de>
-W: http://www.shark-linux.de/shark.html
-S: Maintained
-
ARM/SAMSUNG ARM ARCHITECTURES
M: Ben Dooks <ben-linux@fluff.org>
M: Kukjin Kim <kgene.kim@samsung.com>
bool "Atmel AT91"
select ARCH_REQUIRE_GPIOLIB
select CLKDEV_LOOKUP
- select HAVE_CLK
select IRQ_DOMAIN
select NEED_MACH_GPIO_H
select NEED_MACH_IO_H if PCCARD
bool "Cirrus Logic CLPS711x/EP721x/EP731x-based"
select ARCH_REQUIRE_GPIOLIB
select AUTO_ZRELADDR
- select CLKDEV_LOOKUP
select CLKSRC_MMIO
select COMMON_CLK
select CPU_ARM720T
config ARCH_MSM
bool "Qualcomm MSM"
select ARCH_REQUIRE_GPIOLIB
- select CLKDEV_LOOKUP
select CLKSRC_OF if OF
select COMMON_CLK
select GENERIC_CLOCKEVENTS
select GENERIC_CLOCKEVENTS
select HAVE_ARM_SCU if SMP
select HAVE_ARM_TWD if SMP
- select HAVE_CLK
select HAVE_MACH_CLKDEV
select HAVE_SMP
select MIGHT_HAVE_CACHE_L2X0
select CLKSRC_SAMSUNG_PWM
select GENERIC_CLOCKEVENTS
select GPIO_SAMSUNG
- select HAVE_CLK
select HAVE_S3C2410_I2C if I2C
select HAVE_S3C2410_WATCHDOG if WATCHDOG
select HAVE_S3C_RTC if RTC_CLASS
select CPU_V6
select GENERIC_CLOCKEVENTS
select GPIO_SAMSUNG
- select HAVE_CLK
select HAVE_S3C2410_I2C if I2C
select HAVE_S3C2410_WATCHDOG if WATCHDOG
select HAVE_TCM
select CPU_V6
select GENERIC_CLOCKEVENTS
select GPIO_SAMSUNG
- select HAVE_CLK
select HAVE_S3C2410_I2C if I2C
select HAVE_S3C2410_WATCHDOG if WATCHDOG
select HAVE_S3C_RTC if RTC_CLASS
select CPU_V7
select GENERIC_CLOCKEVENTS
select GPIO_SAMSUNG
- select HAVE_CLK
select HAVE_S3C2410_I2C if I2C
select HAVE_S3C2410_WATCHDOG if WATCHDOG
select HAVE_S3C_RTC if RTC_CLASS
select CPU_V7
select GENERIC_CLOCKEVENTS
select GPIO_SAMSUNG
- select HAVE_CLK
select HAVE_S3C2410_I2C if I2C
select HAVE_S3C2410_WATCHDOG if WATCHDOG
select HAVE_S3C_RTC if RTC_CLASS
select ARCH_REQUIRE_GPIOLIB
select ARCH_SPARSEMEM_ENABLE
select ARM_GIC
- select CLKDEV_LOOKUP
select COMMON_CLK
select CPU_V7
select GENERIC_CLOCKEVENTS
- select HAVE_CLK
select HAVE_S3C2410_I2C if I2C
select HAVE_S3C2410_WATCHDOG if WATCHDOG
select HAVE_S3C_RTC if RTC_CLASS
help
Support for SAMSUNG's EXYNOS SoCs (EXYNOS4/5)
-config ARCH_SHARK
- bool "Shark"
- select ARCH_USES_GETTIMEOFFSET
- select CPU_SA110
- select ISA
- select ISA_DMA
- select NEED_MACH_MEMORY_H
- select PCI
- select VIRT_TO_BUS
- select ZONE_DMA
- help
- Support for the StrongARM based Digital DNARD machine, also known
- as "Shark" (<http://www.shark-linux.de/shark.html>).
-
config ARCH_DAVINCI
bool "TI DaVinci"
select ARCH_HAS_HOLES_MEMORYMODEL
select GENERIC_CLOCKEVENTS
select GENERIC_IRQ_CHIP
select HAVE_IDE
- select NEED_MACH_GPIO_H
select TI_PRIV_EDMA
select USE_OF
select ZONE_DMA
select CLKSRC_MMIO
select GENERIC_CLOCKEVENTS
select GENERIC_IRQ_CHIP
- select HAVE_CLK
select HAVE_IDE
select IRQ_DOMAIN
select NEED_MACH_IO_H if PCCARD
config PCI_SYSCALL
def_bool PCI
-# Select the host bridge type
-config PCI_HOST_VIA82C505
- bool
- depends on PCI && ARCH_SHARK
- default y
-
config PCI_HOST_ITE8152
bool
depends on PCI && MACH_ARMCORE
machine-$(CONFIG_ARCH_S5PC100) += s5pc100
machine-$(CONFIG_ARCH_S5PV210) += s5pv210
machine-$(CONFIG_ARCH_SA1100) += sa1100
-machine-$(CONFIG_ARCH_SHARK) += shark
machine-$(CONFIG_ARCH_SHMOBILE) += shmobile
machine-$(CONFIG_ARCH_SHMOBILE_MULTI) += shmobile
machine-$(CONFIG_ARCH_SIRF) += prima2
--- /dev/null
+
+
+next/cleanup
+ shark/removal
+ git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson.git tags/del-shark-for-v3.13
+ cleanup/dt-clock
+ https://github.com/shesselba/linux-dove.git clk-of-init-v2_for-3.13
+ patch
+ ARM: drop explicit selection of HAVE_CLK and CLKDEV_LOOKUP
+ reneasas/initdata-cleanup
+ git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git tags/renesas-fixes5-for-v3.12
+ renesas/cleanup
+ git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git tags/renesas-cleanup-for-v3.13
+ patch
+ clk: nomadik: fix missing __init on nomadik_src_init
+ renesas/cleanup2
+ git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git tags/renesas-cleanup2-for-v3.13
+ patch
+ ARM: clps711x: Use linux/sched_clock.h
+ ARM: Remove temporary sched_clock.h header
+
+next/soc
+ samsung/s3c64xx-clk
+ http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git tags/samsung-clk-s3c64xx
+ patch
+ ARM: davinci: remove deprecated IRQF_DISABLED
+ renesas/soc
+ git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git tags/renesas-soc-for-v3.13
+ renesas/smp
+ git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git tags/renesas-smp-for-v3.13
+ renesas/soc2
+ git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git tags/renesas-soc2-for-v3.13
+ keystone/soc
+ git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone.git tags/keystone-soc-for-arm-soc
+
+next/drivers
+ davinci/gpio
+ git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci.git tags/davinci-for-v3.13/gpio
+ mvebu/drivers
+ git://git.infradead.org/linux-mvebu.git tags/drivers-3.13
+
+next/boards
+ renesas/boards
+ git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git renesas-boards-for-v3.13
+ renesas/defconfig
+ git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git tags/renesas-defconfig-for-v3.13
+
+next/dt
+ samsung/s3c64xx-dt
+ http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git tags/samsung-dt-s3c64xx
+ ux500/dt
+ git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson.git tags/ux500-dt-for-v3.13-2
+ patch "ARM: ux500: enable appended dtb in u8500_defconfig"
+ ux500/dt2
+ git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson.git tags/ux500-devicetree-2
+ renesas/dt
+ git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git tags/renesas-dt-for-v3.13
+ mvebu/dt
+ git://git.infradead.org/linux-mvebu.git tags/dt-3.13
+ git://git.infradead.org/linux-mvebu.git tags/dt-3.13-2
+
OBJS += ll_char_wr.o font.o
endif
-ifeq ($(CONFIG_ARCH_SHARK),y)
-OBJS += head-shark.o ofw-shark.o
-endif
-
ifeq ($(CONFIG_ARCH_SA1100),y)
OBJS += head-sa1100.o
endif
+++ /dev/null
-/* The head-file for the Shark
- * by Alexander Schulz
- *
- * Does the following:
- * - get the memory layout from firmware. This can only be done as long as the mmu
- * is still on.
- * - switch the mmu off, so we have physical addresses
- * - copy the kernel to 0x08508000. This is done to have a fixed address where the
- * C-parts (misc.c) are executed. This address must be known at compile-time,
- * but the load-address of the kernel depends on how much memory is installed.
- * - Jump to this location.
- * - Set r8 with 0, r7 with the architecture ID for head.S
- */
-
-#include <linux/linkage.h>
-
-#include <asm/assembler.h>
-
- .section ".start", "ax"
-
- .arch armv4
- b __beginning
-
-__ofw_data: .long 0 @ the number of memory blocks
- .space 128 @ (startaddr,size) ...
- .space 128 @ bootargs
- .align
-
-__beginning: mov r4, r0 @ save the entry to the firmware
-
- mov r0, #0xC0 @ disable irq and fiq
- mov r1, r0
- mrs r3, cpsr
- bic r2, r3, r0
- eor r2, r2, r1
- msr cpsr_c, r2
-
- mov r0, r4 @ get the Memory layout from firmware
- adr r1, __ofw_data
- add r2, r1, #4
- mov lr, pc
- b ofw_init
- mov r1, #0
-
- adr r2, __mmu_off @ calculate physical address
- sub r2, r2, #0xf0000000 @ openprom maps us at f000 virt, 0e50 phys
- adr r0, __ofw_data
- ldr r0, [r0, #4]
- add r2, r2, r0
- add r2, r2, #0x00500000
-
- mrc p15, 0, r3, c1, c0
- bic r3, r3, #0xC @ Write Buffer and DCache
- bic r3, r3, #0x1000 @ ICache
- mcr p15, 0, r3, c1, c0 @ disabled
-
- mov r0, #0
- mcr p15, 0, r0, c7, c7 @ flush I,D caches on v4
- mcr p15, 0, r0, c7, c10, 4 @ drain write buffer on v4
- mcr p15, 0, r0, c8, c7 @ flush I,D TLBs on v4
-
- bic r3, r3, #0x1 @ MMU
- mcr p15, 0, r3, c1, c0 @ disabled
-
- mov pc, r2
-
-__copy_target: .long 0x08507FFC
-__copy_end: .long 0x08607FFC
-
- .word _start
- .word __bss_start
-
- .align
-__temp_stack: .space 128
-
-__mmu_off:
- adr r0, __ofw_data @ read the 1. entry of the memory map
- ldr r0, [r0, #4]
- orr r0, r0, #0x00600000
- sub r0, r0, #4
-
- ldr r1, __copy_end
- ldr r3, __copy_target
-
-/* r0 = 0x0e600000 (current end of kernelcode)
- * r3 = 0x08508000 (where it should begin)
- * r1 = 0x08608000 (end of copying area, 1MB)
- * The kernel is compressed, so 1 MB should be enough.
- * copy the kernel to the beginning of physical memory
- * We start from the highest address, so we can copy
- * from 0x08500000 to 0x08508000 if we have only 8MB
- */
-
-/* As we get more 2.6-kernels it gets more and more
- * uncomfortable to be bound to kernel images of 1MB only.
- * So we add a loop here, to be able to copy some more.
- * Alexander Schulz 2005-07-17
- */
-
- mov r4, #3 @ How many megabytes to copy
-
-
-__MoveCode: sub r4, r4, #1
-
-__Copy: ldr r2, [r0], #-4
- str r2, [r1], #-4
- teq r1, r3
- bne __Copy
-
- /* The firmware maps us in blocks of 1 MB, the next block is
- _below_ the last one. So our decrementing source pointer
- ist right here, but the destination pointer must be increased
- by 2 MB */
- add r1, r1, #0x00200000
- add r3, r3, #0x00100000
-
- teq r4, #0
- bne __MoveCode
-
-
- /* and jump to it */
- adr r2, __go_on @ where we want to jump
- adr r0, __ofw_data @ read the 1. entry of the memory map
- ldr r0, [r0, #4]
- sub r2, r2, r0 @ we are mapped add 0e50 now, sub that (-0e00)
- sub r2, r2, #0x00500000 @ -0050
- ldr r0, __copy_target @ and add 0850 8000 instead
- add r0, r0, #4
- add r2, r2, r0
- mov pc, r2 @ and jump there
-
-__go_on:
- adr sp, __temp_stack
- add sp, sp, #128
- adr r0, __ofw_data
- mov lr, pc
- b create_params
-
- mov r8, #0
- mov r7, #15
+++ /dev/null
-/*
- * linux/arch/arm/boot/compressed/ofw-shark.c
- *
- * by Alexander Schulz
- *
- * This file is used to get some basic information
- * about the memory layout of the shark we are running
- * on. Memory is usually divided in blocks a 8 MB.
- * And bootargs are copied from OpenFirmware.
- */
-
-
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <asm/setup.h>
-#include <asm/page.h>
-
-
-asmlinkage void
-create_params (unsigned long *buffer)
-{
- /* Is there a better address? Also change in mach-shark/core.c */
- struct tag *tag = (struct tag *) 0x08003000;
- int j,i,m,k,nr_banks,size;
- unsigned char *c;
-
- k = 0;
-
- /* Head of the taglist */
- tag->hdr.tag = ATAG_CORE;
- tag->hdr.size = tag_size(tag_core);
- tag->u.core.flags = 1;
- tag->u.core.pagesize = PAGE_SIZE;
- tag->u.core.rootdev = 0;
-
- /* Build up one tagged block for each memory region */
- size=0;
- nr_banks=(unsigned int) buffer[0];
- for (j=0;j<nr_banks;j++){
- /* search the lowest address and put it into the next entry */
- /* not a fast sort algorithm, but there are at most 8 entries */
- /* and this is used only once anyway */
- m=0xffffffff;
- for (i=0;i<(unsigned int) buffer[0];i++){
- if (buffer[2*i+1]<m) {
- m=buffer[2*i+1];
- k=i;
- }
- }
-
- tag = tag_next(tag);
- tag->hdr.tag = ATAG_MEM;
- tag->hdr.size = tag_size(tag_mem32);
- tag->u.mem.size = buffer[2*k+2];
- tag->u.mem.start = buffer[2*k+1];
-
- size += buffer[2*k+2];
-
- buffer[2*k+1]=0xffffffff; /* mark as copied */
- }
-
- /* The command line */
- tag = tag_next(tag);
- tag->hdr.tag = ATAG_CMDLINE;
-
- c=(unsigned char *)(&buffer[34]);
- j=0;
- while (*c) tag->u.cmdline.cmdline[j++]=*c++;
-
- tag->u.cmdline.cmdline[j]=0;
- tag->hdr.size = (j + 7 + sizeof(struct tag_header)) >> 2;
-
- /* Hardware revision */
- tag = tag_next(tag);
- tag->hdr.tag = ATAG_REVISION;
- tag->hdr.size = tag_size(tag_revision);
- tag->u.revision.rev = ((unsigned char) buffer[33])-'0';
-
- /* End of the taglist */
- tag = tag_next(tag);
- tag->hdr.tag = 0;
- tag->hdr.size = 0;
-}
-
-
-typedef int (*ofw_handle_t)(void *);
-
-/* Everything below is called with a wrong MMU setting.
- * This means: no string constants, no initialization of
- * arrays, no global variables! This is ugly but I didn't
- * want to write this in assembler :-)
- */
-
-int
-of_decode_int(const unsigned char *p)
-{
- unsigned int i = *p++ << 8;
- i = (i + *p++) << 8;
- i = (i + *p++) << 8;
- return (i + *p);
-}
-
-int
-OF_finddevice(ofw_handle_t openfirmware, char *name)
-{
- unsigned int args[8];
- char service[12];
-
- service[0]='f';
- service[1]='i';
- service[2]='n';
- service[3]='d';
- service[4]='d';
- service[5]='e';
- service[6]='v';
- service[7]='i';
- service[8]='c';
- service[9]='e';
- service[10]='\0';
-
- args[0]=(unsigned int)service;
- args[1]=1;
- args[2]=1;
- args[3]=(unsigned int)name;
-
- if (openfirmware(args) == -1)
- return -1;
- return args[4];
-}
-
-int
-OF_getproplen(ofw_handle_t openfirmware, int handle, char *prop)
-{
- unsigned int args[8];
- char service[12];
-
- service[0]='g';
- service[1]='e';
- service[2]='t';
- service[3]='p';
- service[4]='r';
- service[5]='o';
- service[6]='p';
- service[7]='l';
- service[8]='e';
- service[9]='n';
- service[10]='\0';
-
- args[0] = (unsigned int)service;
- args[1] = 2;
- args[2] = 1;
- args[3] = (unsigned int)handle;
- args[4] = (unsigned int)prop;
-
- if (openfirmware(args) == -1)
- return -1;
- return args[5];
-}
-
-int
-OF_getprop(ofw_handle_t openfirmware, int handle, char *prop, void *buf, unsigned int buflen)
-{
- unsigned int args[8];
- char service[8];
-
- service[0]='g';
- service[1]='e';
- service[2]='t';
- service[3]='p';
- service[4]='r';
- service[5]='o';
- service[6]='p';
- service[7]='\0';
-
- args[0] = (unsigned int)service;
- args[1] = 4;
- args[2] = 1;
- args[3] = (unsigned int)handle;
- args[4] = (unsigned int)prop;
- args[5] = (unsigned int)buf;
- args[6] = buflen;
-
- if (openfirmware(args) == -1)
- return -1;
- return args[7];
-}
-
-asmlinkage void ofw_init(ofw_handle_t o, int *nomr, int *pointer)
-{
- int phandle,i,mem_len,buffer[32];
- char temp[15];
-
- temp[0]='/';
- temp[1]='m';
- temp[2]='e';
- temp[3]='m';
- temp[4]='o';
- temp[5]='r';
- temp[6]='y';
- temp[7]='\0';
-
- phandle=OF_finddevice(o,temp);
-
- temp[0]='r';
- temp[1]='e';
- temp[2]='g';
- temp[3]='\0';
-
- mem_len = OF_getproplen(o,phandle, temp);
- OF_getprop(o,phandle, temp, buffer, mem_len);
- *nomr=mem_len >> 3;
-
- for (i=0; i<=mem_len/4; i++) pointer[i]=of_decode_int((const unsigned char *)&buffer[i]);
-
- temp[0]='/';
- temp[1]='c';
- temp[2]='h';
- temp[3]='o';
- temp[4]='s';
- temp[5]='e';
- temp[6]='n';
- temp[7]='\0';
-
- phandle=OF_finddevice(o,temp);
-
- temp[0]='b';
- temp[1]='o';
- temp[2]='o';
- temp[3]='t';
- temp[4]='a';
- temp[5]='r';
- temp[6]='g';
- temp[7]='s';
- temp[8]='\0';
-
- mem_len = OF_getproplen(o,phandle, temp);
- OF_getprop(o,phandle, temp, buffer, mem_len);
- if (mem_len > 128) mem_len=128;
- for (i=0; i<=mem_len/4; i++) pointer[i+33]=buffer[i];
- pointer[i+33]=0;
-
- temp[0]='/';
- temp[1]='\0';
- phandle=OF_finddevice(o,temp);
- temp[0]='b';
- temp[1]='a';
- temp[2]='n';
- temp[3]='n';
- temp[4]='e';
- temp[5]='r';
- temp[6]='-';
- temp[7]='n';
- temp[8]='a';
- temp[9]='m';
- temp[10]='e';
- temp[11]='\0';
- mem_len = OF_getproplen(o,phandle, temp);
- OF_getprop(o,phandle, temp, buffer, mem_len);
- * ((unsigned char *) &pointer[32]) = ((unsigned char *) buffer)[mem_len-2];
-}
dtb-$(CONFIG_ARCH_DOVE) += dove-cm-a510.dtb \
dove-cubox.dtb \
dove-d2plug.dtb \
+ dove-d3plug.dtb \
dove-dove-db.dtb
dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \
exynos4210-smdkv310.dtb \
armada-xp-axpwifiap.dtb \
armada-xp-db.dtb \
armada-xp-gp.dtb \
+ armada-xp-matrix.dtb \
armada-xp-openblocks-ax3-4.dtb
dtb-$(CONFIG_ARCH_MXC) += \
imx25-karo-tx25.dtb \
dtb-$(CONFIG_ARCH_ORION5X) += orion5x-lacie-ethernet-disk-mini-v2.dtb
dtb-$(CONFIG_ARCH_PRIMA2) += prima2-evb.dtb
dtb-$(CONFIG_ARCH_U8500) += ste-snowball.dtb \
- ste-hrefprev60.dtb \
- ste-hrefv60plus.dtb \
+ ste-hrefprev60-stuib.dtb \
+ ste-hrefprev60-tvk.dtb \
+ ste-hrefv60plus-stuib.dtb \
+ ste-hrefv60plus-tvk.dtb \
ste-ccu8540.dtb \
ste-ccu9540.dtb
dtb-$(CONFIG_ARCH_S3C24XX) += s3c2416-smdk2416.dtb
+dtb-$(CONFIG_ARCH_S3C64XX) += s3c6410-mini6410.dtb \
+ s3c6410-smdk6410.dtb
dtb-$(CONFIG_ARCH_SHMOBILE) += emev2-kzm9d.dtb \
emev2-kzm9d-reference.dtb \
r8a7740-armadillo800eva.dtb \
r8a7740-armadillo800eva-reference.dtb \
r8a7779-marzen.dtb \
r8a7779-marzen-reference.dtb \
+ r8a7791-koelsch.dtb \
r8a7790-lager.dtb \
r8a7790-lager-reference.dtb \
sh73a0-kzm9g.dtb \
#interrupt-cells = <1>;
#size-cells = <1>;
interrupt-controller;
+ msi-controller;
};
coherency-fabric@20200 {
i2c0: i2c@11000 {
compatible = "marvell,mv64xxx-i2c";
- reg = <0x11000 0x20>;
#address-cells = <1>;
#size-cells = <0>;
interrupts = <31>;
i2c1: i2c@11100 {
compatible = "marvell,mv64xxx-i2c";
- reg = <0x11100 0x20>;
#address-cells = <1>;
#size-cells = <0>;
interrupts = <32>;
#address-cells = <3>;
#size-cells = <2>;
+ msi-parent = <&mpic>;
bus-range = <0x00 0xff>;
ranges =
};
};
+ i2c0: i2c@11000 {
+ reg = <0x11000 0x20>;
+ };
+
+ i2c1: i2c@11100 {
+ reg = <0x11100 0x20>;
+ };
+
usb@50000 {
clocks = <&coreclk 0>;
};
--- /dev/null
+/*
+ * Device Tree file for Marvell Armada XP Matrix board
+ *
+ * Copyright (C) 2013 Marvell
+ *
+ * Lior Amsalem <alior@marvell.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+#include "armada-xp-mv78460.dtsi"
+
+/ {
+ model = "Marvell Armada XP Matrix Board";
+ compatible = "marvell,axp-matrix", "marvell,armadaxp-mv78460", "marvell,armadaxp", "marvell,armada-370-xp";
+
+ chosen {
+ bootargs = "console=ttyS0,115200 earlyprintk";
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x00000000 0 0x80000000>; /* 2 GB */
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
+ MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000>;
+
+ internal-regs {
+ serial@12000 {
+ clock-frequency = <250000000>;
+ status = "okay";
+ };
+ serial@12100 {
+ clock-frequency = <250000000>;
+ status = "okay";
+ };
+ serial@12200 {
+ clock-frequency = <250000000>;
+ status = "okay";
+ };
+ serial@12300 {
+ clock-frequency = <250000000>;
+ status = "okay";
+ };
+
+ sata@a0000 {
+ nr-ports = <2>;
+ status = "okay";
+ };
+
+ ethernet@30000 {
+ status = "okay";
+ phy-mode = "sgmii";
+ };
+
+ pcie-controller {
+ status = "okay";
+
+ pcie@1,0 {
+ /* Port 0, Lane 0 */
+ status = "okay";
+ };
+ };
+
+ usb@50000 {
+ status = "okay";
+ };
+ };
+ };
+};
#address-cells = <3>;
#size-cells = <2>;
+ msi-parent = <&mpic>;
bus-range = <0x00 0xff>;
ranges =
#address-cells = <3>;
#size-cells = <2>;
+ msi-parent = <&mpic>;
bus-range = <0x00 0xff>;
ranges =
#address-cells = <3>;
#size-cells = <2>;
+ msi-parent = <&mpic>;
bus-range = <0x00 0xff>;
ranges =
};
};
+ i2c0: i2c@11000 {
+ compatible = "marvell,mv78230-i2c", "marvell,mv64xxx-i2c";
+ reg = <0x11000 0x100>;
+ };
+
+ i2c1: i2c@11100 {
+ compatible = "marvell,mv78230-i2c", "marvell,mv64xxx-i2c";
+ reg = <0x11100 0x100>;
+ };
+
usb@50000 {
clocks = <&gateclk 18>;
};
/dts-v1/;
-/include/ "dove.dtsi"
+#include "dove.dtsi"
/ {
model = "Compulab CM-A510";
/dts-v1/;
-/include/ "dove.dtsi"
+#include "dove.dtsi"
/ {
model = "SolidRun CuBox";
/dts-v1/;
-/include/ "dove.dtsi"
+#include "dove.dtsi"
/ {
model = "Globalscale D2Plug";
--- /dev/null
+/dts-v1/;
+
+#include "dove.dtsi"
+
+/ {
+ model = "Globalscale D3Plug";
+ compatible = "globalscale,d3plug", "marvell,dove";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x40000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/mmcblk0p2 rw rootwait";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&pmx_gpio_0 &pmx_gpio_1 &pmx_gpio_2>;
+ pinctrl-names = "default";
+
+ wlan-act {
+ label = "wlan-act";
+ gpios = <&gpio0 0 1>;
+ };
+
+ wlan-ap {
+ label = "wlan-ap";
+ gpios = <&gpio0 1 1>;
+ };
+
+ status {
+ label = "status";
+ gpios = <&gpio0 2 1>;
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb_power: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "USB Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio0 8 0>;
+ pinctrl-0 = <&pmx_gpio_8>;
+ pinctrl-names = "default";
+ };
+ };
+};
+
+&uart0 { status = "okay"; };
+&sata0 { status = "okay"; };
+&i2c0 { status = "okay"; };
+
+/* Samsung M8G2F eMMC */
+&sdio0 {
+ status = "okay";
+ non-removable;
+ bus-width = <4>;
+};
+
+/* Marvell SD8787 WLAN/BT */
+&sdio1 {
+ status = "okay";
+ non-removable;
+};
+
+&spi0 {
+ status = "okay";
+
+ /* spi0.0: 2M Flash Macronix MX25L1605D */
+ spi-flash@0 {
+ compatible = "st,m25l1605d";
+ spi-max-frequency = <86000000>;
+ reg = <0>;
+ };
+};
+
+&pcie {
+ status = "okay";
+ /* Fresco Logic USB3.0 xHCI controller */
+ pcie-port@0 {
+ status = "okay";
+ reset-gpios = <&gpio0 26 1>;
+ reset-delay-us = <20000>;
+ pinctrl-0 = <&pmx_camera_gpio>;
+ pinctrl-names = "default";
+ };
+ /* Mini-PCIe slot */
+ pcie-port@1 {
+ status = "okay";
+ reset-gpios = <&gpio0 25 1>;
+ };
+};
/dts-v1/;
-/include/ "dove.dtsi"
+#include "dove.dtsi"
/ {
model = "Marvell DB-MV88AP510-BP Development Board";
/include/ "skeleton.dtsi"
+#define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16))
+
/ {
compatible = "marvell,dove";
model = "Marvell Armada 88AP510 SoC";
+ interrupt-parent = <&intc>;
aliases {
gpio0 = &gpio0;
marvell,tauros2-cache-features = <0>;
};
- soc@f1000000 {
- compatible = "simple-bus";
- #address-cells = <1>;
+ mbus {
+ compatible = "marvell,dove-mbus", "marvell,mbus", "simple-bus";
+ #address-cells = <2>;
#size-cells = <1>;
- interrupt-parent = <&intc>;
-
- ranges = <0xc8000000 0xc8000000 0x0100000 /* CESA SRAM 1M */
- 0xe0000000 0xe0000000 0x8000000 /* PCIe0 Mem 128M */
- 0xe8000000 0xe8000000 0x8000000 /* PCIe1 Mem 128M */
- 0xf0000000 0xf0000000 0x0100000 /* ScratchPad 1M */
- 0x00000000 0xf1000000 0x1000000 /* SB/NB regs 16M */
- 0xf2000000 0xf2000000 0x0100000 /* PCIe0 I/O 1M */
- 0xf2100000 0xf2100000 0x0100000 /* PCIe0 I/O 1M */
- 0xf8000000 0xf8000000 0x8000000>; /* BootROM 128M */
-
- timer: timer@20300 {
- compatible = "marvell,orion-timer";
- reg = <0x20300 0x20>;
- interrupt-parent = <&bridge_intc>;
- interrupts = <1>, <2>;
- clocks = <&core_clk 0>;
- };
-
- intc: main-interrupt-ctrl@20200 {
- compatible = "marvell,orion-intc";
- interrupt-controller;
- #interrupt-cells = <1>;
- reg = <0x20200 0x10>, <0x20210 0x10>;
- };
-
- bridge_intc: bridge-interrupt-ctrl@20110 {
- compatible = "marvell,orion-bridge-intc";
- interrupt-controller;
- #interrupt-cells = <1>;
- reg = <0x20110 0x8>;
- interrupts = <0>;
- marvell,#interrupts = <5>;
- };
-
- core_clk: core-clocks@d0214 {
- compatible = "marvell,dove-core-clock";
- reg = <0xd0214 0x4>;
- #clock-cells = <1>;
- };
-
- gate_clk: clock-gating-ctrl@d0038 {
- compatible = "marvell,dove-gating-clock";
- reg = <0xd0038 0x4>;
- clocks = <&core_clk 0>;
- #clock-cells = <1>;
- };
-
- thermal: thermal-diode@d001c {
- compatible = "marvell,dove-thermal";
- reg = <0xd001c 0x0c>, <0xd005c 0x08>;
- };
-
- uart0: serial@12000 {
- compatible = "ns16550a";
- reg = <0x12000 0x100>;
- reg-shift = <2>;
- interrupts = <7>;
- clocks = <&core_clk 0>;
+ controller = <&mbusc>;
+ pcie-mem-aperture = <0xe0000000 0x10000000>; /* 256M MEM space */
+ pcie-io-aperture = <0xf2000000 0x00200000>; /* 2M I/O space */
+
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x0100000 /* MBUS regs 1M */
+ MBUS_ID(0xf0, 0x02) 0 0xf1800000 0x1000000 /* AXI regs 16M */
+ MBUS_ID(0x01, 0xfd) 0 0xf8000000 0x8000000 /* BootROM 128M */
+ MBUS_ID(0x03, 0x01) 0 0xc8000000 0x0100000 /* CESA SRAM 1M */
+ MBUS_ID(0x0d, 0x00) 0 0xf0000000 0x0100000>; /* PMU SRAM 1M */
+
+ pcie: pcie-controller {
+ compatible = "marvell,dove-pcie";
status = "disabled";
- };
-
- uart1: serial@12100 {
- compatible = "ns16550a";
- reg = <0x12100 0x100>;
- reg-shift = <2>;
- interrupts = <8>;
- clocks = <&core_clk 0>;
- pinctrl-0 = <&pmx_uart1>;
- pinctrl-names = "default";
- status = "disabled";
- };
-
- uart2: serial@12200 {
- compatible = "ns16550a";
- reg = <0x12000 0x100>;
- reg-shift = <2>;
- interrupts = <9>;
- clocks = <&core_clk 0>;
- status = "disabled";
- };
-
- uart3: serial@12300 {
- compatible = "ns16550a";
- reg = <0x12100 0x100>;
- reg-shift = <2>;
- interrupts = <10>;
- clocks = <&core_clk 0>;
- status = "disabled";
- };
-
- gpio0: gpio-ctrl@d0400 {
- compatible = "marvell,orion-gpio";
- #gpio-cells = <2>;
- gpio-controller;
- reg = <0xd0400 0x20>;
- ngpios = <32>;
- interrupt-controller;
- #interrupt-cells = <2>;
- interrupts = <12>, <13>, <14>, <60>;
- };
-
- gpio1: gpio-ctrl@d0420 {
- compatible = "marvell,orion-gpio";
- #gpio-cells = <2>;
- gpio-controller;
- reg = <0xd0420 0x20>;
- ngpios = <32>;
- interrupt-controller;
- #interrupt-cells = <2>;
- interrupts = <61>;
- };
-
- gpio2: gpio-ctrl@e8400 {
- compatible = "marvell,orion-gpio";
- #gpio-cells = <2>;
- gpio-controller;
- reg = <0xe8400 0x0c>;
- ngpios = <8>;
- };
-
- pinctrl: pin-ctrl@d0200 {
- compatible = "marvell,dove-pinctrl";
- reg = <0xd0200 0x10>;
- clocks = <&gate_clk 22>;
-
- pmx_gpio_0: pmx-gpio-0 {
- marvell,pins = "mpp0";
- marvell,function = "gpio";
- };
-
- pmx_gpio_1: pmx-gpio-1 {
- marvell,pins = "mpp1";
- marvell,function = "gpio";
- };
-
- pmx_gpio_2: pmx-gpio-2 {
- marvell,pins = "mpp2";
- marvell,function = "gpio";
- };
-
- pmx_gpio_3: pmx-gpio-3 {
- marvell,pins = "mpp3";
- marvell,function = "gpio";
- };
-
- pmx_gpio_4: pmx-gpio-4 {
- marvell,pins = "mpp4";
- marvell,function = "gpio";
- };
-
- pmx_gpio_5: pmx-gpio-5 {
- marvell,pins = "mpp5";
- marvell,function = "gpio";
- };
-
- pmx_gpio_6: pmx-gpio-6 {
- marvell,pins = "mpp6";
- marvell,function = "gpio";
- };
-
- pmx_gpio_7: pmx-gpio-7 {
- marvell,pins = "mpp7";
- marvell,function = "gpio";
- };
-
- pmx_gpio_8: pmx-gpio-8 {
- marvell,pins = "mpp8";
- marvell,function = "gpio";
- };
-
- pmx_gpio_9: pmx-gpio-9 {
- marvell,pins = "mpp9";
- marvell,function = "gpio";
- };
-
- pmx_gpio_10: pmx-gpio-10 {
- marvell,pins = "mpp10";
- marvell,function = "gpio";
- };
-
- pmx_gpio_11: pmx-gpio-11 {
- marvell,pins = "mpp11";
- marvell,function = "gpio";
- };
-
- pmx_gpio_12: pmx-gpio-12 {
- marvell,pins = "mpp12";
- marvell,function = "gpio";
- };
-
- pmx_gpio_13: pmx-gpio-13 {
- marvell,pins = "mpp13";
- marvell,function = "gpio";
- };
-
- pmx_gpio_14: pmx-gpio-14 {
- marvell,pins = "mpp14";
- marvell,function = "gpio";
- };
-
- pmx_gpio_15: pmx-gpio-15 {
- marvell,pins = "mpp15";
- marvell,function = "gpio";
- };
-
- pmx_gpio_16: pmx-gpio-16 {
- marvell,pins = "mpp16";
- marvell,function = "gpio";
- };
-
- pmx_gpio_17: pmx-gpio-17 {
- marvell,pins = "mpp17";
- marvell,function = "gpio";
- };
-
- pmx_gpio_18: pmx-gpio-18 {
- marvell,pins = "mpp18";
- marvell,function = "gpio";
- };
-
- pmx_gpio_19: pmx-gpio-19 {
- marvell,pins = "mpp19";
- marvell,function = "gpio";
- };
-
- pmx_gpio_20: pmx-gpio-20 {
- marvell,pins = "mpp20";
- marvell,function = "gpio";
- };
-
- pmx_gpio_21: pmx-gpio-21 {
- marvell,pins = "mpp21";
- marvell,function = "gpio";
+ device_type = "pci";
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ msi-parent = <&intc>;
+ bus-range = <0x00 0xff>;
+
+ ranges = <0x82000000 0x0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x2000
+ 0x82000000 0x0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x2000
+ 0x82000000 0x1 0x0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 Mem */
+ 0x81000000 0x1 0x0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 I/O */
+ 0x82000000 0x2 0x0 MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 1.0 Mem */
+ 0x81000000 0x2 0x0 MBUS_ID(0x08, 0xe0) 0 1 0>; /* Port 1.0 I/O */
+
+ pcie-port@0 {
+ device_type = "pci";
+ status = "disabled";
+ assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+ reg = <0x0800 0 0 0 0>;
+ clocks = <&gate_clk 4>;
+ marvell,pcie-port = <0>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+ 0x81000000 0 0 0x81000000 0x1 0 1 0>;
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &intc 16>;
+ };
+
+ pcie-port@1 {
+ device_type = "pci";
+ status = "disabled";
+ assigned-addresses = <0x82002800 0 0x80000 0 0x2000>;
+ reg = <0x1000 0 0 0 0>;
+ clocks = <&gate_clk 5>;
+ marvell,pcie-port = <1>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
+ 0x81000000 0 0 0x81000000 0x2 0 1 0>;
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &intc 18>;
};
-
- pmx_camera: pmx-camera {
- marvell,pins = "mpp_camera";
- marvell,function = "camera";
- };
-
- pmx_camera_gpio: pmx-camera-gpio {
- marvell,pins = "mpp_camera";
- marvell,function = "gpio";
- };
-
- pmx_sdio0: pmx-sdio0 {
- marvell,pins = "mpp_sdio0";
- marvell,function = "sdio0";
- };
-
- pmx_sdio0_gpio: pmx-sdio0-gpio {
- marvell,pins = "mpp_sdio0";
- marvell,function = "gpio";
- };
-
- pmx_sdio1: pmx-sdio1 {
- marvell,pins = "mpp_sdio1";
- marvell,function = "sdio1";
- };
-
- pmx_sdio1_gpio: pmx-sdio1-gpio {
- marvell,pins = "mpp_sdio1";
- marvell,function = "gpio";
- };
-
- pmx_audio1_gpio: pmx-audio1-gpio {
- marvell,pins = "mpp_audio1";
- marvell,function = "gpio";
- };
-
- pmx_spi0: pmx-spi0 {
- marvell,pins = "mpp_spi0";
- marvell,function = "spi0";
- };
-
- pmx_spi0_gpio: pmx-spi0-gpio {
- marvell,pins = "mpp_spi0";
- marvell,function = "gpio";
- };
-
- pmx_uart1: pmx-uart1 {
- marvell,pins = "mpp_uart1";
- marvell,function = "uart1";
- };
-
- pmx_uart1_gpio: pmx-uart1-gpio {
- marvell,pins = "mpp_uart1";
- marvell,function = "gpio";
- };
-
- pmx_nand: pmx-nand {
- marvell,pins = "mpp_nand";
- marvell,function = "nand";
- };
-
- pmx_nand_gpo: pmx-nand-gpo {
- marvell,pins = "mpp_nand";
- marvell,function = "gpo";
- };
- };
-
- spi0: spi-ctrl@10600 {
- compatible = "marvell,orion-spi";
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <0>;
- interrupts = <6>;
- reg = <0x10600 0x28>;
- clocks = <&core_clk 0>;
- pinctrl-0 = <&pmx_spi0>;
- pinctrl-names = "default";
- status = "disabled";
};
- spi1: spi-ctrl@14600 {
- compatible = "marvell,orion-spi";
+ internal-regs {
+ compatible = "simple-bus";
#address-cells = <1>;
- #size-cells = <0>;
- cell-index = <1>;
- interrupts = <5>;
- reg = <0x14600 0x28>;
- clocks = <&core_clk 0>;
- status = "disabled";
- };
-
- i2c0: i2c-ctrl@11000 {
- compatible = "marvell,mv64xxx-i2c";
- reg = <0x11000 0x20>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <11>;
- clock-frequency = <400000>;
- timeout-ms = <1000>;
- clocks = <&core_clk 0>;
- status = "disabled";
- };
-
- ehci0: usb-host@50000 {
- compatible = "marvell,orion-ehci";
- reg = <0x50000 0x1000>;
- interrupts = <24>;
- clocks = <&gate_clk 0>;
- status = "okay";
- };
-
- ehci1: usb-host@51000 {
- compatible = "marvell,orion-ehci";
- reg = <0x51000 0x1000>;
- interrupts = <25>;
- clocks = <&gate_clk 1>;
- status = "okay";
- };
-
- sdio0: sdio-host@92000 {
- compatible = "marvell,dove-sdhci";
- reg = <0x92000 0x100>;
- interrupts = <35>, <37>;
- clocks = <&gate_clk 8>;
- pinctrl-0 = <&pmx_sdio0>;
- pinctrl-names = "default";
- status = "disabled";
- };
-
- sdio1: sdio-host@90000 {
- compatible = "marvell,dove-sdhci";
- reg = <0x90000 0x100>;
- interrupts = <36>, <38>;
- clocks = <&gate_clk 9>;
- pinctrl-0 = <&pmx_sdio1>;
- pinctrl-names = "default";
- status = "disabled";
- };
-
- sata0: sata-host@a0000 {
- compatible = "marvell,orion-sata";
- reg = <0xa0000 0x2400>;
- interrupts = <62>;
- clocks = <&gate_clk 3>;
- nr-ports = <1>;
- status = "disabled";
- };
-
- rtc: real-time-clock@d8500 {
- compatible = "marvell,orion-rtc";
- reg = <0xd8500 0x20>;
- };
-
- crypto: crypto-engine@30000 {
- compatible = "marvell,orion-crypto";
- reg = <0x30000 0x10000>,
- <0xc8000000 0x800>;
- reg-names = "regs", "sram";
- interrupts = <31>;
- clocks = <&gate_clk 15>;
- status = "okay";
- };
-
- xor0: dma-engine@60800 {
- compatible = "marvell,orion-xor";
- reg = <0x60800 0x100
- 0x60a00 0x100>;
- clocks = <&gate_clk 23>;
- status = "okay";
-
- channel0 {
- interrupts = <39>;
- dmacap,memcpy;
- dmacap,xor;
- };
-
- channel1 {
- interrupts = <40>;
- dmacap,memset;
- dmacap,memcpy;
- dmacap,xor;
- };
- };
-
- xor1: dma-engine@60900 {
- compatible = "marvell,orion-xor";
- reg = <0x60900 0x100
- 0x60b00 0x100>;
- clocks = <&gate_clk 24>;
- status = "okay";
-
- channel0 {
- interrupts = <42>;
- dmacap,memcpy;
- dmacap,xor;
- };
-
- channel1 {
- interrupts = <43>;
- dmacap,memset;
- dmacap,memcpy;
- dmacap,xor;
- };
- };
-
- mdio: mdio-bus@72004 {
- compatible = "marvell,orion-mdio";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x72004 0x84>;
- interrupts = <30>;
- clocks = <&gate_clk 2>;
- status = "disabled";
-
- ethphy: ethernet-phy {
- device-type = "ethernet-phy";
- /* set phy address in board file */
- };
- };
-
- eth: ethernet-controller@72000 {
- compatible = "marvell,orion-eth";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x72000 0x4000>;
- clocks = <&gate_clk 2>;
- marvell,tx-checksum-limit = <1600>;
- status = "disabled";
-
- ethernet-port@0 {
- device_type = "network";
- compatible = "marvell,orion-eth-port";
- reg = <0>;
- interrupts = <29>;
- /* overwrite MAC address in bootloader */
- local-mac-address = [00 00 00 00 00 00];
- phy-handle = <ðphy>;
+ #size-cells = <1>;
+ ranges = <0x00000000 MBUS_ID(0xf0, 0x01) 0 0x0100000 /* MBUS regs 1M */
+ 0x00800000 MBUS_ID(0xf0, 0x02) 0 0x1000000 /* AXI regs 16M */
+ 0xffffe000 MBUS_ID(0x03, 0x01) 0 0x0000800 /* CESA SRAM 2k */
+ 0xfffff000 MBUS_ID(0x0d, 0x00) 0 0x0000800>; /* PMU SRAM 2k */
+
+ mbusc: mbus-ctrl@20000 {
+ compatible = "marvell,mbus-controller";
+ reg = <0x20000 0x80>, <0x800100 0x8>;
+ };
+
+ timer: timer@20300 {
+ compatible = "marvell,orion-timer";
+ reg = <0x20300 0x20>;
+ interrupt-parent = <&bridge_intc>;
+ interrupts = <1>, <2>;
+ clocks = <&core_clk 0>;
+ };
+
+ intc: main-interrupt-ctrl@20200 {
+ compatible = "marvell,orion-intc";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ reg = <0x20200 0x10>, <0x20210 0x10>;
+ };
+
+ bridge_intc: bridge-interrupt-ctrl@20110 {
+ compatible = "marvell,orion-bridge-intc";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ reg = <0x20110 0x8>;
+ interrupts = <0>;
+ marvell,#interrupts = <5>;
+ };
+
+ core_clk: core-clocks@d0214 {
+ compatible = "marvell,dove-core-clock";
+ reg = <0xd0214 0x4>;
+ #clock-cells = <1>;
+ };
+
+ gate_clk: clock-gating-ctrl@d0038 {
+ compatible = "marvell,dove-gating-clock";
+ reg = <0xd0038 0x4>;
+ clocks = <&core_clk 0>;
+ #clock-cells = <1>;
+ };
+
+ thermal: thermal-diode@d001c {
+ compatible = "marvell,dove-thermal";
+ reg = <0xd001c 0x0c>, <0xd005c 0x08>;
+ };
+
+ uart0: serial@12000 {
+ compatible = "ns16550a";
+ reg = <0x12000 0x100>;
+ reg-shift = <2>;
+ interrupts = <7>;
+ clocks = <&core_clk 0>;
+ status = "disabled";
+ };
+
+ uart1: serial@12100 {
+ compatible = "ns16550a";
+ reg = <0x12100 0x100>;
+ reg-shift = <2>;
+ interrupts = <8>;
+ clocks = <&core_clk 0>;
+ pinctrl-0 = <&pmx_uart1>;
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
+ uart2: serial@12200 {
+ compatible = "ns16550a";
+ reg = <0x12000 0x100>;
+ reg-shift = <2>;
+ interrupts = <9>;
+ clocks = <&core_clk 0>;
+ status = "disabled";
+ };
+
+ uart3: serial@12300 {
+ compatible = "ns16550a";
+ reg = <0x12100 0x100>;
+ reg-shift = <2>;
+ interrupts = <10>;
+ clocks = <&core_clk 0>;
+ status = "disabled";
+ };
+
+ gpio0: gpio-ctrl@d0400 {
+ compatible = "marvell,orion-gpio";
+ #gpio-cells = <2>;
+ gpio-controller;
+ reg = <0xd0400 0x20>;
+ ngpios = <32>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <12>, <13>, <14>, <60>;
+ };
+
+ gpio1: gpio-ctrl@d0420 {
+ compatible = "marvell,orion-gpio";
+ #gpio-cells = <2>;
+ gpio-controller;
+ reg = <0xd0420 0x20>;
+ ngpios = <32>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <61>;
+ };
+
+ gpio2: gpio-ctrl@e8400 {
+ compatible = "marvell,orion-gpio";
+ #gpio-cells = <2>;
+ gpio-controller;
+ reg = <0xe8400 0x0c>;
+ ngpios = <8>;
+ };
+
+ pinctrl: pin-ctrl@d0200 {
+ compatible = "marvell,dove-pinctrl";
+ reg = <0xd0200 0x10>;
+ clocks = <&gate_clk 22>;
+
+ pmx_gpio_0: pmx-gpio-0 {
+ marvell,pins = "mpp0";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_1: pmx-gpio-1 {
+ marvell,pins = "mpp1";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_2: pmx-gpio-2 {
+ marvell,pins = "mpp2";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_3: pmx-gpio-3 {
+ marvell,pins = "mpp3";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_4: pmx-gpio-4 {
+ marvell,pins = "mpp4";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_5: pmx-gpio-5 {
+ marvell,pins = "mpp5";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_6: pmx-gpio-6 {
+ marvell,pins = "mpp6";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_7: pmx-gpio-7 {
+ marvell,pins = "mpp7";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_8: pmx-gpio-8 {
+ marvell,pins = "mpp8";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_9: pmx-gpio-9 {
+ marvell,pins = "mpp9";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_10: pmx-gpio-10 {
+ marvell,pins = "mpp10";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_11: pmx-gpio-11 {
+ marvell,pins = "mpp11";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_12: pmx-gpio-12 {
+ marvell,pins = "mpp12";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_13: pmx-gpio-13 {
+ marvell,pins = "mpp13";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_14: pmx-gpio-14 {
+ marvell,pins = "mpp14";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_15: pmx-gpio-15 {
+ marvell,pins = "mpp15";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_16: pmx-gpio-16 {
+ marvell,pins = "mpp16";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_17: pmx-gpio-17 {
+ marvell,pins = "mpp17";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_18: pmx-gpio-18 {
+ marvell,pins = "mpp18";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_19: pmx-gpio-19 {
+ marvell,pins = "mpp19";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_20: pmx-gpio-20 {
+ marvell,pins = "mpp20";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_21: pmx-gpio-21 {
+ marvell,pins = "mpp21";
+ marvell,function = "gpio";
+ };
+
+ pmx_camera: pmx-camera {
+ marvell,pins = "mpp_camera";
+ marvell,function = "camera";
+ };
+
+ pmx_camera_gpio: pmx-camera-gpio {
+ marvell,pins = "mpp_camera";
+ marvell,function = "gpio";
+ };
+
+ pmx_sdio0: pmx-sdio0 {
+ marvell,pins = "mpp_sdio0";
+ marvell,function = "sdio0";
+ };
+
+ pmx_sdio0_gpio: pmx-sdio0-gpio {
+ marvell,pins = "mpp_sdio0";
+ marvell,function = "gpio";
+ };
+
+ pmx_sdio1: pmx-sdio1 {
+ marvell,pins = "mpp_sdio1";
+ marvell,function = "sdio1";
+ };
+
+ pmx_sdio1_gpio: pmx-sdio1-gpio {
+ marvell,pins = "mpp_sdio1";
+ marvell,function = "gpio";
+ };
+
+ pmx_audio1_gpio: pmx-audio1-gpio {
+ marvell,pins = "mpp_audio1";
+ marvell,function = "gpio";
+ };
+
+ pmx_spi0: pmx-spi0 {
+ marvell,pins = "mpp_spi0";
+ marvell,function = "spi0";
+ };
+
+ pmx_spi0_gpio: pmx-spi0-gpio {
+ marvell,pins = "mpp_spi0";
+ marvell,function = "gpio";
+ };
+
+ pmx_uart1: pmx-uart1 {
+ marvell,pins = "mpp_uart1";
+ marvell,function = "uart1";
+ };
+
+ pmx_uart1_gpio: pmx-uart1-gpio {
+ marvell,pins = "mpp_uart1";
+ marvell,function = "gpio";
+ };
+
+ pmx_nand: pmx-nand {
+ marvell,pins = "mpp_nand";
+ marvell,function = "nand";
+ };
+
+ pmx_nand_gpo: pmx-nand-gpo {
+ marvell,pins = "mpp_nand";
+ marvell,function = "gpo";
+ };
+ };
+
+ spi0: spi-ctrl@10600 {
+ compatible = "marvell,orion-spi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <0>;
+ interrupts = <6>;
+ reg = <0x10600 0x28>;
+ clocks = <&core_clk 0>;
+ pinctrl-0 = <&pmx_spi0>;
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
+ spi1: spi-ctrl@14600 {
+ compatible = "marvell,orion-spi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <1>;
+ interrupts = <5>;
+ reg = <0x14600 0x28>;
+ clocks = <&core_clk 0>;
+ status = "disabled";
+ };
+
+ i2c0: i2c-ctrl@11000 {
+ compatible = "marvell,mv64xxx-i2c";
+ reg = <0x11000 0x20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <11>;
+ clock-frequency = <400000>;
+ timeout-ms = <1000>;
+ clocks = <&core_clk 0>;
+ status = "disabled";
+ };
+
+ ehci0: usb-host@50000 {
+ compatible = "marvell,orion-ehci";
+ reg = <0x50000 0x1000>;
+ interrupts = <24>;
+ clocks = <&gate_clk 0>;
+ status = "okay";
+ };
+
+ ehci1: usb-host@51000 {
+ compatible = "marvell,orion-ehci";
+ reg = <0x51000 0x1000>;
+ interrupts = <25>;
+ clocks = <&gate_clk 1>;
+ status = "okay";
+ };
+
+ sdio0: sdio-host@92000 {
+ compatible = "marvell,dove-sdhci";
+ reg = <0x92000 0x100>;
+ interrupts = <35>, <37>;
+ clocks = <&gate_clk 8>;
+ pinctrl-0 = <&pmx_sdio0>;
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
+ sdio1: sdio-host@90000 {
+ compatible = "marvell,dove-sdhci";
+ reg = <0x90000 0x100>;
+ interrupts = <36>, <38>;
+ clocks = <&gate_clk 9>;
+ pinctrl-0 = <&pmx_sdio1>;
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
+ sata0: sata-host@a0000 {
+ compatible = "marvell,orion-sata";
+ reg = <0xa0000 0x2400>;
+ interrupts = <62>;
+ clocks = <&gate_clk 3>;
+ nr-ports = <1>;
+ status = "disabled";
+ };
+
+ rtc: real-time-clock@d8500 {
+ compatible = "marvell,orion-rtc";
+ reg = <0xd8500 0x20>;
+ };
+
+ crypto: crypto-engine@30000 {
+ compatible = "marvell,orion-crypto";
+ reg = <0x30000 0x10000>,
+ <0xffffe000 0x800>;
+ reg-names = "regs", "sram";
+ interrupts = <31>;
+ clocks = <&gate_clk 15>;
+ status = "okay";
+ };
+
+ xor0: dma-engine@60800 {
+ compatible = "marvell,orion-xor";
+ reg = <0x60800 0x100
+ 0x60a00 0x100>;
+ clocks = <&gate_clk 23>;
+ status = "okay";
+
+ channel0 {
+ interrupts = <39>;
+ dmacap,memcpy;
+ dmacap,xor;
+ };
+
+ channel1 {
+ interrupts = <40>;
+ dmacap,memcpy;
+ dmacap,xor;
+ };
+ };
+
+ xor1: dma-engine@60900 {
+ compatible = "marvell,orion-xor";
+ reg = <0x60900 0x100
+ 0x60b00 0x100>;
+ clocks = <&gate_clk 24>;
+ status = "okay";
+
+ channel0 {
+ interrupts = <42>;
+ dmacap,memcpy;
+ dmacap,xor;
+ };
+
+ channel1 {
+ interrupts = <43>;
+ dmacap,memcpy;
+ dmacap,xor;
+ };
+ };
+
+ mdio: mdio-bus@72004 {
+ compatible = "marvell,orion-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x72004 0x84>;
+ interrupts = <30>;
+ clocks = <&gate_clk 2>;
+ status = "disabled";
+
+ ethphy: ethernet-phy {
+ device-type = "ethernet-phy";
+ /* set phy address in board file */
+ };
+ };
+
+ eth: ethernet-ctrl@72000 {
+ compatible = "marvell,orion-eth";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x72000 0x4000>;
+ clocks = <&gate_clk 2>;
+ marvell,tx-checksum-limit = <1600>;
+ status = "disabled";
+
+ ethernet-port@0 {
+ device_type = "network";
+ compatible = "marvell,orion-eth-port";
+ reg = <0>;
+ interrupts = <29>;
+ /* overwrite MAC address in bootloader */
+ local-mac-address = [00 00 00 00 00 00];
+ phy-handle = <ðphy>;
+ };
};
};
};
compatible = "marvell,db-88f6281-bp", "marvell,kirkwood-88f6281", "marvell,kirkwood";
mbus {
- ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>;
pcie-controller {
status = "okay";
compatible = "marvell,db-88f6282-bp", "marvell,kirkwood-88f6282", "marvell,kirkwood";
mbus {
- ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>;
pcie-controller {
status = "okay";
status = "ok";
};
- nand@3000000 {
- pinctrl-0 = <&pmx_nand>;
- pinctrl-names = "default";
- chip-delay = <25>;
- status = "okay";
-
- partition@0 {
- label = "uboot";
- reg = <0x0 0x100000>;
- };
-
- partition@100000 {
- label = "uImage";
- reg = <0x100000 0x400000>;
- };
-
- partition@500000 {
- label = "root";
- reg = <0x500000 0x1fb00000>;
- };
- };
-
sata@80000 {
nr-ports = <2>;
status = "okay";
};
};
+&nand {
+ pinctrl-0 = <&pmx_nand>;
+ pinctrl-names = "default";
+ chip-delay = <25>;
+ status = "okay";
+
+ partition@0 {
+ label = "uboot";
+ reg = <0x0 0x100000>;
+ };
+
+ partition@100000 {
+ label = "uImage";
+ reg = <0x100000 0x400000>;
+ };
+
+ partition@500000 {
+ label = "root";
+ reg = <0x500000 0x1fb00000>;
+ };
+};
+
&mdio {
status = "okay";
status = "okay";
nr-ports = <2>;
};
-
- nand@3000000 {
- pinctrl-0 = <&pmx_nand>;
- pinctrl-names = "default";
- status = "okay";
- chip-delay = <35>;
-
- partition@0 {
- label = "u-boot";
- reg = <0x0000000 0x100000>;
- read-only;
- };
-
- partition@100000 {
- label = "uImage";
- reg = <0x0100000 0x500000>;
- };
-
- partition@600000 {
- label = "ramdisk";
- reg = <0x0600000 0x500000>;
- };
-
- partition@b00000 {
- label = "image";
- reg = <0x0b00000 0x6600000>;
- };
-
- partition@7100000 {
- label = "mini firmware";
- reg = <0x7100000 0xa00000>;
- };
-
- partition@7b00000 {
- label = "config";
- reg = <0x7b00000 0x500000>;
- };
- };
};
regulators {
};
};
+&nand {
+ pinctrl-0 = <&pmx_nand>;
+ pinctrl-names = "default";
+ status = "okay";
+ chip-delay = <35>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0000000 0x100000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "uImage";
+ reg = <0x0100000 0x500000>;
+ };
+
+ partition@600000 {
+ label = "ramdisk";
+ reg = <0x0600000 0x500000>;
+ };
+
+ partition@b00000 {
+ label = "image";
+ reg = <0x0b00000 0x6600000>;
+ };
+
+ partition@7100000 {
+ label = "mini firmware";
+ reg = <0x7100000 0xa00000>;
+ };
+
+ partition@7b00000 {
+ label = "config";
+ reg = <0x7b00000 0x500000>;
+ };
+};
+
&mdio {
status = "okay";
serial@12000 {
status = "ok";
};
-
- nand@3000000 {
- status = "okay";
-
- partition@0 {
- label = "u-boot";
- reg = <0x0000000 0x100000>;
- read-only;
- };
-
- partition@100000 {
- label = "uImage";
- reg = <0x0100000 0x400000>;
- };
-
- partition@500000 {
- label = "data";
- reg = <0x0500000 0xfb00000>;
- };
- };
};
gpio-leds {
compatible = "gpio-leds";
};
};
+&nand {
+ status = "okay";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0000000 0x100000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "uImage";
+ reg = <0x0100000 0x400000>;
+ };
+
+ partition@500000 {
+ label = "data";
+ reg = <0x0500000 0xfb00000>;
+ };
+};
+
&mdio {
status = "okay";
status = "ok";
};
- nand@3000000 {
- chip-delay = <40>;
- status = "okay";
-
- partition@0 {
- label = "u-boot";
- reg = <0x0000000 0x100000>;
- read-only;
- };
-
- partition@100000 {
- label = "uImage";
- reg = <0x0100000 0x400000>;
- };
-
- partition@500000 {
- label = "pogoplug";
- reg = <0x0500000 0x2000000>;
- };
-
- partition@2500000 {
- label = "root";
- reg = <0x02500000 0xd800000>;
- };
- };
sata@80000 {
status = "okay";
nr-ports = <2>;
};
};
+&nand {
+ chip-delay = <40>;
+ status = "okay";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0000000 0x100000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "uImage";
+ reg = <0x0100000 0x400000>;
+ };
+
+ partition@500000 {
+ label = "pogoplug";
+ reg = <0x0500000 0x2000000>;
+ };
+
+ partition@2500000 {
+ label = "root";
+ reg = <0x02500000 0xd800000>;
+ };
+};
+
&mdio {
status = "okay";
status = "ok";
};
- nand@3000000 {
- status = "okay";
-
- partition@0 {
- label = "u-boot";
- reg = <0x00000000 0x00100000>;
- read-only;
- };
-
- partition@100000 {
- label = "uImage";
- reg = <0x00100000 0x00400000>;
- };
-
- partition@500000 {
- label = "data";
- reg = <0x00500000 0x1fb00000>;
- };
- };
-
sata@80000 {
status = "okay";
nr-ports = <1>;
};
};
+&nand {
+ status = "okay";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x00000000 0x00100000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "uImage";
+ reg = <0x00100000 0x00400000>;
+ };
+
+ partition@500000 {
+ label = "data";
+ reg = <0x00500000 0x1fb00000>;
+ };
+};
+
&mdio {
status = "okay";
/ {
model = "RaidSonic ICY BOX IB-NAS62x0 (Rev B)";
- compatible = "raidsonic,ib-nas6210-b", "raidsonic,ib-nas6220-b", "raidsonic,ib-nas6210", "raidsonic,ib-nas6220", "raidsonic,ib-nas62x0", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+ compatible = "raidsonic,ib-nas6210-b", "raidsonic,ib-nas6220-b", "raidsonic,ib-nas6210", "raidsonic,ib-nas6220", "raidsonic,ib-nas62x0", "marvell,kirkwood-88f6281", "marvell,kirkwood";
memory {
device_type = "memory";
marvell,function = "gpio";
};
};
+
serial@12000 {
status = "okay";
};
status = "okay";
nr-ports = <2>;
};
-
- nand@3000000 {
- status = "okay";
- pinctrl-0 = <&pmx_nand>;
- pinctrl-names = "default";
-
- partition@0 {
- label = "u-boot";
- reg = <0x0000000 0x100000>;
- };
-
- partition@100000 {
- label = "uImage";
- reg = <0x0100000 0x600000>;
- };
-
- partition@700000 {
- label = "root";
- reg = <0x0700000 0xf900000>;
- };
-
- };
};
gpio_keys {
gpios = <&gpio0 28 1>;
};
};
+
gpio-leds {
compatible = "gpio-leds";
pinctrl-0 = <&pmx_led_os_red &pmx_led_os_green
gpios = <&gpio0 27 0>;
};
};
+
gpio_poweroff {
compatible = "gpio-poweroff";
pinctrl-0 = <&pmx_power_off>;
pinctrl-names = "default";
gpios = <&gpio0 24 0>;
};
+};
+
+&nand {
+ status = "okay";
+ pinctrl-0 = <&pmx_nand>;
+ pinctrl-names = "default";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0000000 0xe0000>;
+ };
+ partition@e0000 {
+ label = "u-boot environment";
+ reg = <0xe0000 0x100000>;
+ };
+
+ partition@100000 {
+ label = "uImage";
+ reg = <0x0100000 0x600000>;
+ };
+
+ partition@700000 {
+ label = "root";
+ reg = <0x0700000 0xf900000>;
+ };
};
ð0 {
status = "okay";
+
ethernet0-port@0 {
phy-handle = <ðphy0>;
};
};
mbus {
- ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>;
pcie-controller {
status = "okay";
serial@12000 {
status = "ok";
};
-
- nand@3000000 {
- status = "okay";
-
- partition@0 {
- label = "uboot";
- reg = <0x0000000 0xc0000>;
- };
-
- partition@a0000 {
- label = "env";
- reg = <0xa0000 0x20000>;
- };
-
- partition@100000 {
- label = "zImage";
- reg = <0x100000 0x300000>;
- };
-
- partition@540000 {
- label = "initrd";
- reg = <0x540000 0x300000>;
- };
-
- partition@980000 {
- label = "boot";
- reg = <0x980000 0x1f400000>;
- };
- };
};
gpio-leds {
};
};
+&nand {
+ status = "okay";
+
+ partition@0 {
+ label = "uboot";
+ reg = <0x0000000 0xc0000>;
+ };
+
+ partition@a0000 {
+ label = "env";
+ reg = <0xa0000 0x20000>;
+ };
+
+ partition@100000 {
+ label = "zImage";
+ reg = <0x100000 0x300000>;
+ };
+
+ partition@540000 {
+ label = "initrd";
+ reg = <0x540000 0x300000>;
+ };
+
+ partition@980000 {
+ label = "boot";
+ reg = <0x980000 0x1f400000>;
+ };
+};
+
&mdio {
status = "okay";
status = "ok";
};
- nand@3000000 {
- status = "okay";
-
- partition@0 {
- label = "u-boot";
- reg = <0x0000000 0x100000>;
- read-only;
- };
-
- partition@a0000 {
- label = "env";
- reg = <0xa0000 0x20000>;
- read-only;
- };
-
- partition@100000 {
- label = "uImage";
- reg = <0x100000 0x300000>;
- };
-
- partition@400000 {
- label = "uInitrd";
- reg = <0x540000 0x1000000>;
- };
- };
sata@80000 {
status = "okay";
nr-ports = <2>;
};
};
+&nand {
+ status = "okay";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0000000 0x100000>;
+ read-only;
+ };
+
+ partition@a0000 {
+ label = "env";
+ reg = <0xa0000 0x20000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "uImage";
+ reg = <0x100000 0x300000>;
+ };
+
+ partition@400000 {
+ label = "uInitrd";
+ reg = <0x540000 0x1000000>;
+ };
+};
+
&mdio {
status = "okay";
serial@12000 {
status = "ok";
};
-
- nand@3000000 {
- pinctrl-0 = <&pmx_nand>;
- pinctrl-names = "default";
- status = "ok";
- chip-delay = <25>;
- };
};
i2c@0 {
};
};
+&nand {
+ pinctrl-0 = <&pmx_nand>;
+ pinctrl-names = "default";
+ status = "ok";
+ chip-delay = <25>;
+};
+
&mdio {
status = "okay";
};
mbus {
- ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>;
pcie-controller {
status = "okay";
pinctrl-names = "default";
};
- nand@3000000 {
- pinctrl-0 = <&pmx_nand>;
- pinctrl-names = "default";
- status = "okay";
-
- partition@0 {
- label = "uboot";
- reg = <0x0000000 0x100000>;
- };
-
- partition@100000 {
- label = "env";
- reg = <0x100000 0x80000>;
- };
-
- partition@180000 {
- label = "fdt";
- reg = <0x180000 0x80000>;
- };
-
- partition@200000 {
- label = "kernel";
- reg = <0x200000 0x400000>;
- };
-
- partition@600000 {
- label = "rootfs";
- reg = <0x600000 0x1fa00000>;
- };
- };
-
rtc@10300 {
status = "disabled";
};
};
};
+&nand {
+ pinctrl-0 = <&pmx_nand>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ partition@0 {
+ label = "uboot";
+ reg = <0x0000000 0x100000>;
+ };
+
+ partition@100000 {
+ label = "env";
+ reg = <0x100000 0x80000>;
+ };
+
+ partition@180000 {
+ label = "fdt";
+ reg = <0x180000 0x80000>;
+ };
+
+ partition@200000 {
+ label = "kernel";
+ reg = <0x200000 0x400000>;
+ };
+
+ partition@600000 {
+ label = "rootfs";
+ reg = <0x600000 0x1fa00000>;
+ };
+};
+
&mdio {
status = "okay";
};
mbus {
- ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>;
pcie-controller {
status = "okay";
status = "okay";
};
- nand@3000000 {
- status = "okay";
-
- partition@0 {
- label = "u-boot";
- reg = <0x0000000 0x180000>;
- read-only;
- };
-
- partition@180000 {
- label = "u-boot-env";
- reg = <0x180000 0x20000>;
- };
-
- partition@200000 {
- label = "uImage";
- reg = <0x0200000 0x600000>;
- };
-
- partition@800000 {
- label = "minirootfs";
- reg = <0x0800000 0x1000000>;
- };
-
- partition@1800000 {
- label = "jffs2";
- reg = <0x1800000 0x6800000>;
- };
- };
-
sata@80000 {
status = "okay";
nr-ports = <2>;
};
};
+&nand {
+ status = "okay";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0000000 0x180000>;
+ read-only;
+ };
+
+ partition@180000 {
+ label = "u-boot-env";
+ reg = <0x180000 0x20000>;
+ };
+
+ partition@200000 {
+ label = "uImage";
+ reg = <0x0200000 0x600000>;
+ };
+
+ partition@800000 {
+ label = "minirootfs";
+ reg = <0x0800000 0x1000000>;
+ };
+
+ partition@1800000 {
+ label = "jffs2";
+ reg = <0x1800000 0x6800000>;
+ };
+};
+
&mdio {
status = "okay";
nr-ports = <2>;
};
- nand@3000000 {
- status = "okay";
- chip-delay = <35>;
-
- partition@0 {
- label = "uboot";
- reg = <0x0000000 0x0100000>;
- read-only;
- };
- partition@100000 {
- label = "uboot_env";
- reg = <0x0100000 0x0080000>;
- };
- partition@180000 {
- label = "key_store";
- reg = <0x0180000 0x0080000>;
- };
- partition@200000 {
- label = "info";
- reg = <0x0200000 0x0080000>;
- };
- partition@280000 {
- label = "etc";
- reg = <0x0280000 0x0a00000>;
- };
- partition@c80000 {
- label = "kernel_1";
- reg = <0x0c80000 0x0a00000>;
- };
- partition@1680000 {
- label = "rootfs1";
- reg = <0x1680000 0x2fc0000>;
- };
- partition@4640000 {
- label = "kernel_2";
- reg = <0x4640000 0x0a00000>;
- };
- partition@5040000 {
- label = "rootfs2";
- reg = <0x5040000 0x2fc0000>;
- };
- };
-
pcie-controller {
status = "okay";
};
};
};
+
+&nand {
+ status = "okay";
+ chip-delay = <35>;
+
+ partition@0 {
+ label = "uboot";
+ reg = <0x0000000 0x0100000>;
+ read-only;
+ };
+ partition@100000 {
+ label = "uboot_env";
+ reg = <0x0100000 0x0080000>;
+ };
+ partition@180000 {
+ label = "key_store";
+ reg = <0x0180000 0x0080000>;
+ };
+ partition@200000 {
+ label = "info";
+ reg = <0x0200000 0x0080000>;
+ };
+ partition@280000 {
+ label = "etc";
+ reg = <0x0280000 0x0a00000>;
+ };
+ partition@c80000 {
+ label = "kernel_1";
+ reg = <0x0c80000 0x0a00000>;
+ };
+ partition@1680000 {
+ label = "rootfs1";
+ reg = <0x1680000 0x2fc0000>;
+ };
+ partition@4640000 {
+ label = "kernel_2";
+ reg = <0x4640000 0x0a00000>;
+ };
+ partition@5040000 {
+ label = "rootfs2";
+ reg = <0x5040000 0x2fc0000>;
+ };
+};
};
mbus {
- ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>;
pcie-controller {
status = "okay";
pinctrl-names = "default";
};
- nand@3000000 {
- chip-delay = <25>;
- status = "okay";
- pinctrl-0 = <&pmx_nand>;
- pinctrl-names = "default";
-
- partition@0 {
- label = "uboot";
- reg = <0x0 0x90000>;
- };
-
- partition@90000 {
- label = "env";
- reg = <0x90000 0x44000>;
- };
-
- partition@d4000 {
- label = "test";
- reg = <0xd4000 0x24000>;
- };
-
- partition@f4000 {
- label = "conf";
- reg = <0xf4000 0x400000>;
- };
-
- partition@4f4000 {
- label = "linux";
- reg = <0x4f4000 0x1d20000>;
- };
-
- partition@2214000 {
- label = "user";
- reg = <0x2214000 0x1dec000>;
- };
- };
-
sata@80000 {
nr-ports = <1>;
status = "okay";
};
};
+&nand {
+ chip-delay = <25>;
+ status = "okay";
+ pinctrl-0 = <&pmx_nand>;
+ pinctrl-names = "default";
+
+ partition@0 {
+ label = "uboot";
+ reg = <0x0 0x90000>;
+ };
+
+ partition@90000 {
+ label = "env";
+ reg = <0x90000 0x44000>;
+ };
+
+ partition@d4000 {
+ label = "test";
+ reg = <0xd4000 0x24000>;
+ };
+
+ partition@f4000 {
+ label = "conf";
+ reg = <0xf4000 0x400000>;
+ };
+
+ partition@4f4000 {
+ label = "linux";
+ reg = <0x4f4000 0x1d20000>;
+ };
+
+ partition@2214000 {
+ label = "user";
+ reg = <0x2214000 0x1dec000>;
+ };
+};
+
&mdio {
status = "okay";
pinctrl-names = "default";
status = "okay";
};
-
- nand@3000000 {
- pinctrl-0 = <&pmx_nand>;
- pinctrl-names = "default";
- status = "okay";
-
- partition@0 {
- label = "u-boot";
- reg = <0x0000000 0x100000>;
- };
-
- partition@100000 {
- label = "uImage";
- reg = <0x0100000 0x400000>;
- };
-
- partition@500000 {
- label = "root";
- reg = <0x0500000 0x1fb00000>;
- };
- };
};
regulators {
};
};
+&nand {
+ pinctrl-0 = <&pmx_nand>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0000000 0x100000>;
+ };
+
+ partition@100000 {
+ label = "uImage";
+ reg = <0x0100000 0x400000>;
+ };
+
+ partition@500000 {
+ label = "root";
+ reg = <0x0500000 0x1fb00000>;
+ };
+};
+
&mdio {
status = "okay";
pinctrl-names = "default";
};
- nand@3000000 {
- status = "okay";
- pinctrl-0 = <&pmx_nand>;
- pinctrl-names = "default";
-
- partition@0 {
- label = "u-boot";
- reg = <0x0000000 0x180000>;
- };
-
- partition@180000 {
- label = "u-boot env";
- reg = <0x0180000 0x20000>;
- };
-
- partition@200000 {
- label = "uImage";
- reg = <0x0200000 0x600000>;
- };
-
- partition@800000 {
- label = "uInitrd";
- reg = <0x0800000 0x1000000>;
- };
-
- partition@1800000 {
- label = "rootfs";
- reg = <0x1800000 0xe800000>;
- };
- };
-
sata@80000 {
status = "okay";
nr-ports = <1>;
};
};
+&nand {
+ status = "okay";
+ pinctrl-0 = <&pmx_nand>;
+ pinctrl-names = "default";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0000000 0x180000>;
+ };
+
+ partition@180000 {
+ label = "u-boot env";
+ reg = <0x0180000 0x20000>;
+ };
+
+ partition@200000 {
+ label = "uImage";
+ reg = <0x0200000 0x600000>;
+ };
+
+ partition@800000 {
+ label = "uInitrd";
+ reg = <0x0800000 0x1000000>;
+ };
+
+ partition@1800000 {
+ label = "rootfs";
+ reg = <0x1800000 0xe800000>;
+ };
+};
+
&mdio {
status = "okay";
/ {
mbus {
- ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>;
pcie-controller {
status = "okay";
compatible = "marvell,kirkwood-mbus", "simple-bus";
#address-cells = <2>;
#size-cells = <1>;
+ /* If a board file needs to change this ranges it must replace it completely */
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 /* internal-regs */
+ MBUS_ID(0x01, 0x2f) 0 0xf4000000 0x10000 /* nand flash */
+ MBUS_ID(0x03, 0x01) 0 0xf5000000 0x10000 /* crypto sram */
+ >;
controller = <&mbusc>;
pcie-mem-aperture = <0xe0000000 0x10000000>; /* 256 MiB memory space */
pcie-io-aperture = <0xf2000000 0x100000>; /* 1 MiB I/O space */
+
+ crypto@0301 {
+ compatible = "marvell,orion-crypto";
+ reg = <MBUS_ID(0xf0, 0x01) 0x30000 0x10000>,
+ <MBUS_ID(0x03, 0x01) 0 0x800>;
+ reg-names = "regs", "sram";
+ interrupts = <22>;
+ clocks = <&gate_clk 17>;
+ status = "okay";
+ };
+
+ nand: nand@012f {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ cle = <0>;
+ ale = <1>;
+ bank-width = <1>;
+ compatible = "marvell,orion-nand";
+ reg = <MBUS_ID(0x01, 0x2f) 0 0x400>;
+ chip-delay = <25>;
+ /* set partition map and/or chip-delay in board dts */
+ clocks = <&gate_clk 7>;
+ status = "disabled";
+ };
};
ocp@f1000000 {
compatible = "simple-bus";
- ranges = <0x00000000 0xf1000000 0x0100000
- 0xf4000000 0xf4000000 0x0000400
- 0xf5000000 0xf5000000 0x0000400>;
+ ranges = <0x00000000 0xf1000000 0x0100000>;
#address-cells = <1>;
#size-cells = <1>;
status = "okay";
};
- nand@3000000 {
- #address-cells = <1>;
- #size-cells = <1>;
- cle = <0>;
- ale = <1>;
- bank-width = <1>;
- compatible = "marvell,orion-nand";
- reg = <0xf4000000 0x400>;
- chip-delay = <25>;
- /* set partition map and/or chip-delay in board dts */
- clocks = <&gate_clk 7>;
- status = "disabled";
- };
-
i2c@11000 {
compatible = "marvell,mv64xxx-i2c";
reg = <0x11000 0x20>;
status = "disabled";
};
- crypto@30000 {
- compatible = "marvell,orion-crypto";
- reg = <0x30000 0x10000>,
- <0xf5000000 0x800>;
- reg-names = "regs", "sram";
- interrupts = <22>;
- clocks = <&gate_clk 17>;
- status = "okay";
- };
-
mdio: mdio-bus@72004 {
compatible = "marvell,orion-mdio";
#address-cells = <1>;
/ {
model = "TI OMAP3 BeagleBoard xM";
- compatible = "ti,omap3-beagle-xm", "ti,omap3-beagle", "ti,omap3";
+ compatible = "ti,omap3-beagle-xm", "ti,omap36xx", "ti,omap3";
cpus {
cpu@0 {
#address-cells = <1>;
#size-cells = <0>;
pinctrl-single,register-width = <16>;
- pinctrl-single,function-mask = <0x7f1f>;
+ pinctrl-single,function-mask = <0xff1f>;
};
omap3_pmx_wkup: pinmux@0x48002a00 {
#address-cells = <1>;
#size-cells = <0>;
pinctrl-single,register-width = <16>;
- pinctrl-single,function-mask = <0x7f1f>;
+ pinctrl-single,function-mask = <0xff1f>;
};
gpio1: gpio@48310000 {
/dts-v1/;
/include/ "r8a73a4.dtsi"
+#include <dt-bindings/gpio/gpio.h>
/ {
model = "APE6EVM";
reg = <0 0x40000000 0 0x40000000>;
};
+ vcc_mmc0: regulator@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "MMC0 Vcc";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+
+ vcc_sdhi0: regulator@1 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "SDHI0 Vcc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&pfc 76 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ /* Common 3.3V rail, used by several devices on APE6EVM */
+ ape6evm_fixed_3v3: regulator@2 {
+ compatible = "regulator-fixed";
+ regulator-name = "3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
lbsc {
compatible = "simple-bus";
#address-cells = <1>;
renesas,groups = "scifa0_data";
renesas,function = "scifa0";
};
+
+ mmc0_pins: mmcif {
+ renesas,groups = "mmc0_data8", "mmc0_ctrl";
+ renesas,function = "mmc0";
+ };
+
+ sdhi0_pins: sdhi0 {
+ renesas,groups = "sdhi0_data4", "sdhi0_ctrl", "sdhi0_cd";
+ renesas,function = "sdhi0";
+ };
+
+ sdhi1_pins: sdhi1 {
+ renesas,groups = "sdhi1_data4", "sdhi1_ctrl";
+ renesas,function = "sdhi1";
+ };
+};
+
+&mmcif0 {
+ vmmc-supply = <&vcc_mmc0>;
+ bus-width = <8>;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
+ status = "okay";
+};
+
+&sdhi0 {
+ vmmc-supply = <&vcc_sdhi0>;
+ bus-width = <4>;
+ toshiba,mmc-wrprotect-disable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhi0_pins>;
+ status = "okay";
+};
+
+&sdhi1 {
+ vmmc-supply = <&ape6evm_fixed_3v3>;
+ bus-width = <4>;
+ broken-cd;
+ toshiba,mmc-wrprotect-disable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhi1_pins>;
+ status = "okay";
};
reg = <0>;
clock-frequency = <1300000000>;
};
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a15";
+ reg = <1>;
+ clock-frequency = <1300000000>;
+ };
+
+ cpu2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a15";
+ reg = <2>;
+ clock-frequency = <1300000000>;
+ };
+
+ cpu3: cpu@3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a15";
+ reg = <3>;
+ clock-frequency = <1300000000>;
+ };
+
+ cpu4: cpu@4 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0x100>;
+ clock-frequency = <780000000>;
+ };
+
+ cpu5: cpu@5 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0x101>;
+ clock-frequency = <780000000>;
+ };
+
+ cpu6: cpu@6 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0x102>;
+ clock-frequency = <780000000>;
+ };
+
+ cpu7: cpu@7 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0x103>;
+ clock-frequency = <780000000>;
+ };
};
gic: interrupt-controller@f1001000 {
--- /dev/null
+/*
+ * Device Tree Source for the Koelsch board
+ *
+ * Copyright (C) 2013 Renesas Electronics Corporation
+ * Copyright (C) 2013 Renesas Solutions Corp.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/dts-v1/;
+/include/ "r8a7791.dtsi"
+
+/ {
+ model = "Koelsch";
+ compatible = "renesas,koelsch", "renesas,r8a7791";
+
+ chosen {
+ bootargs = "console=ttySC6,115200 ignore_loglevel rw root=/dev/nfs ip=dhcp";
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ reg = <0 0x40000000 0 0x80000000>;
+ };
+
+ lbsc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+};
--- /dev/null
+/*
+ * Samsung's S3C6400 SoC device tree source
+ *
+ * Copyright (c) 2013 Tomasz Figa <tomasz.figa@gmail.com>
+ *
+ * Samsung's S3C6400 SoC device nodes are listed in this file. S3C6400
+ * based board files can include this file and provide values for board specfic
+ * bindings.
+ *
+ * Note: This file does not include device nodes for all the controllers in
+ * S3C6400 SoC. As device tree coverage for S3C6400 increases, additional
+ * nodes can be added to this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include "s3c64xx.dtsi"
+
+/ {
+ compatible = "samsung,s3c6400";
+};
+
+&vic0 {
+ valid-mask = <0xfffffe1f>;
+ valid-wakeup-mask = <0x00200004>;
+};
+
+&vic1 {
+ valid-mask = <0xffffffff>;
+ valid-wakeup-mask = <0x53020000>;
+};
+
+&soc {
+ clocks: clock-controller@7e00f000 {
+ compatible = "samsung,s3c6400-clock";
+ reg = <0x7e00f000 0x1000>;
+ #clock-cells = <1>;
+ };
+};
--- /dev/null
+/*
+ * Samsung's S3C6410 based Mini6410 board device tree source
+ *
+ * Copyright (c) 2013 Tomasz Figa <tomasz.figa@gmail.com>
+ *
+ * Device tree source file for FriendlyARM Mini6410 board which is based on
+ * Samsung's S3C6410 SoC.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+#include "s3c6410.dtsi"
+
+/ {
+ model = "FriendlyARM Mini6410 board based on S3C6410";
+ compatible = "friendlyarm,mini6410", "samsung,s3c6410";
+
+ memory {
+ reg = <0x50000000 0x10000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttySAC0,115200n8 earlyprintk rootwait root=/dev/mmcblk0p1";
+ };
+
+ clocks {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fin_pll: oscillator@0 {
+ compatible = "fixed-clock";
+ reg = <0>;
+ clock-frequency = <12000000>;
+ clock-output-names = "fin_pll";
+ #clock-cells = <0>;
+ };
+
+ xusbxti: oscillator@1 {
+ compatible = "fixed-clock";
+ reg = <1>;
+ clock-output-names = "xusbxti";
+ clock-frequency = <48000000>;
+ #clock-cells = <0>;
+ };
+ };
+
+ srom-cs1@18000000 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x18000000 0x8000000>;
+ ranges;
+
+ ethernet@18000000 {
+ compatible = "davicom,dm9000";
+ reg = <0x18000000 0x2 0x18000004 0x2>;
+ interrupt-parent = <&gpn>;
+ interrupts = <7 IRQ_TYPE_LEVEL_HIGH>;
+ davicom,no-eeprom;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_keys>;
+ autorepeat;
+
+ button-k1 {
+ label = "K1";
+ gpios = <&gpn 0 GPIO_ACTIVE_LOW>;
+ linux,code = <2>;
+ debounce-interval = <20>;
+ };
+
+ button-k2 {
+ label = "K2";
+ gpios = <&gpn 1 GPIO_ACTIVE_LOW>;
+ linux,code = <3>;
+ debounce-interval = <20>;
+ };
+
+ button-k3 {
+ label = "K3";
+ gpios = <&gpn 2 GPIO_ACTIVE_LOW>;
+ linux,code = <4>;
+ debounce-interval = <20>;
+ };
+
+ button-k4 {
+ label = "K4";
+ gpios = <&gpn 3 GPIO_ACTIVE_LOW>;
+ linux,code = <5>;
+ debounce-interval = <20>;
+ };
+
+ button-k5 {
+ label = "K5";
+ gpios = <&gpn 4 GPIO_ACTIVE_LOW>;
+ linux,code = <6>;
+ debounce-interval = <20>;
+ };
+
+ button-k6 {
+ label = "K6";
+ gpios = <&gpn 5 GPIO_ACTIVE_LOW>;
+ linux,code = <7>;
+ debounce-interval = <20>;
+ };
+
+ button-k7 {
+ label = "K7";
+ gpios = <&gpl 11 GPIO_ACTIVE_LOW>;
+ linux,code = <8>;
+ debounce-interval = <20>;
+ };
+
+ button-k8 {
+ label = "K8";
+ gpios = <&gpl 12 GPIO_ACTIVE_LOW>;
+ linux,code = <9>;
+ debounce-interval = <20>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_leds>;
+
+ led-1 {
+ label = "LED1";
+ gpios = <&gpk 4 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ led-2 {
+ label = "LED2";
+ gpios = <&gpk 5 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "mmc0";
+ };
+
+ led-3 {
+ label = "LED3";
+ gpios = <&gpk 6 GPIO_ACTIVE_LOW>;
+ };
+
+ led-4 {
+ label = "LED4";
+ gpios = <&gpk 7 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ buzzer {
+ compatible = "pwm-beeper";
+ pwms = <&pwm 0 1000000 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_out>;
+ };
+};
+
+&sdhci0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd0_clk>, <&sd0_cmd>, <&sd0_cd>, <&sd0_bus4>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_data>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_data>, <&uart1_fctl>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_data>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_data>;
+ status = "okay";
+};
+
+&pwm {
+ status = "okay";
+};
+
+&pinctrl0 {
+ gpio_leds: gpio-leds {
+ samsung,pins = "gpk-4", "gpk-5", "gpk-6", "gpk-7";
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ gpio_keys: gpio-keys {
+ samsung,pins = "gpn-0", "gpn-1", "gpn-2", "gpn-3",
+ "gpn-4", "gpn-5", "gpl-11", "gpl-12";
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_bus>;
+ status = "okay";
+
+ eeprom@50 {
+ compatible = "atmel,24c08";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
+};
--- /dev/null
+/*
+ * Samsung S3C6410 based SMDK6410 board device tree source.
+ *
+ * Copyright (c) 2013 Tomasz Figa <tomasz.figa@gmail.com>
+ *
+ * Device tree source file for SAMSUNG SMDK6410 board which is based on
+ * Samsung's S3C6410 SoC.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+#include "s3c6410.dtsi"
+
+/ {
+ model = "SAMSUNG SMDK6410 board based on S3C6410";
+ compatible = "samsung,mini6410", "samsung,s3c6410";
+
+ memory {
+ reg = <0x50000000 0x8000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttySAC0,115200n8 earlyprintk rootwait root=/dev/mmcblk0p1";
+ };
+
+ clocks {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fin_pll: oscillator@0 {
+ compatible = "fixed-clock";
+ reg = <0>;
+ clock-frequency = <12000000>;
+ clock-output-names = "fin_pll";
+ #clock-cells = <0>;
+ };
+
+ xusbxti: oscillator@1 {
+ compatible = "fixed-clock";
+ reg = <1>;
+ clock-output-names = "xusbxti";
+ clock-frequency = <48000000>;
+ #clock-cells = <0>;
+ };
+ };
+
+ srom-cs1@18000000 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x18000000 0x8000000>;
+ ranges;
+
+ ethernet@18000000 {
+ compatible = "smsc,lan9115";
+ reg = <0x18000000 0x10000>;
+ interrupt-parent = <&gpn>;
+ interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
+ phy-mode = "mii";
+ reg-io-width = <4>;
+ smsc,force-internal-phy;
+ };
+ };
+};
+
+&sdhci0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd0_clk>, <&sd0_cmd>, <&sd0_cd>, <&sd0_bus4>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_data>, <&uart0_fctl>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_data>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_data>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_data>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Samsung's S3C6410 SoC device tree source
+ *
+ * Copyright (c) 2013 Tomasz Figa <tomasz.figa@gmail.com>
+ *
+ * Samsung's S3C6410 SoC device nodes are listed in this file. S3C6410
+ * based board files can include this file and provide values for board specfic
+ * bindings.
+ *
+ * Note: This file does not include device nodes for all the controllers in
+ * S3C6410 SoC. As device tree coverage for S3C6410 increases, additional
+ * nodes can be added to this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include "s3c64xx.dtsi"
+
+/ {
+ compatible = "samsung,s3c6410";
+
+ aliases {
+ i2c1 = &i2c1;
+ };
+};
+
+&vic0 {
+ valid-mask = <0xffffff7f>;
+ valid-wakeup-mask = <0x00200004>;
+};
+
+&vic1 {
+ valid-mask = <0xffffffff>;
+ valid-wakeup-mask = <0x53020000>;
+};
+
+&soc {
+ clocks: clock-controller@7e00f000 {
+ compatible = "samsung,s3c6410-clock";
+ reg = <0x7e00f000 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ i2c1: i2c@7f00f000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x7f00f000 0x1000>;
+ interrupt-parent = <&vic0>;
+ interrupts = <5>;
+ clock-names = "i2c";
+ clocks = <&clocks PCLK_IIC1>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+};
--- /dev/null
+/*
+ * Samsung's S3C64xx SoC series common device tree source
+ * - pin control-related definitions
+ *
+ * Copyright (c) 2013 Tomasz Figa <tomasz.figa@gmail.com>
+ *
+ * Samsung's S3C64xx SoCs pin banks, pin-mux and pin-config options are
+ * listed as device tree nodes in this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#define PIN_PULL_NONE 0
+#define PIN_PULL_DOWN 1
+#define PIN_PULL_UP 2
+
+&pinctrl0 {
+ /*
+ * Pin banks
+ */
+
+ gpa: gpa {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpb: gpb {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpc: gpc {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpd: gpd {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpe: gpe {
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ gpf: gpf {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpg: gpg {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gph: gph {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpi: gpi {
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ gpj: gpj {
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ gpk: gpk {
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ gpl: gpl {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpm: gpm {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpn: gpn {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpo: gpo {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpp: gpp {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpq: gpq {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ /*
+ * Pin groups
+ */
+
+ uart0_data: uart0-data {
+ samsung,pins = "gpa-0", "gpa-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ uart0_fctl: uart0-fctl {
+ samsung,pins = "gpa-2", "gpa-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ uart1_data: uart1-data {
+ samsung,pins = "gpa-4", "gpa-5";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ uart1_fctl: uart1-fctl {
+ samsung,pins = "gpa-6", "gpa-7";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ uart2_data: uart2-data {
+ samsung,pins = "gpb-0", "gpb-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ uart3_data: uart3-data {
+ samsung,pins = "gpb-2", "gpb-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ ext_dma_0: ext-dma-0 {
+ samsung,pins = "gpb-0", "gpb-1";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ ext_dma_1: ext-dma-1 {
+ samsung,pins = "gpb-2", "gpb-3";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ irda_data_0: irda-data-0 {
+ samsung,pins = "gpb-0", "gpb-1";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ irda_data_1: irda-data-1 {
+ samsung,pins = "gpb-2", "gpb-3";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ irda_sdbw: irda-sdbw {
+ samsung,pins = "gpb-4";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ i2c0_bus: i2c0-bus {
+ samsung,pins = "gpb-5", "gpb-6";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_UP>;
+ };
+
+ i2c1_bus: i2c1-bus {
+ /* S3C6410-only */
+ samsung,pins = "gpb-2", "gpb-3";
+ samsung,pin-function = <6>;
+ samsung,pin-pud = <PIN_PULL_UP>;
+ };
+
+ spi0_bus: spi0-bus {
+ samsung,pins = "gpc-0", "gpc-1", "gpc-2";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_UP>;
+ };
+
+ spi0_cs: spi0-cs {
+ samsung,pins = "gpc-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ spi1_bus: spi1-bus {
+ samsung,pins = "gpc-4", "gpc-5", "gpc-6";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_UP>;
+ };
+
+ spi1_cs: spi1-cs {
+ samsung,pins = "gpc-7";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ sd0_cmd: sd0-cmd {
+ samsung,pins = "gpg-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ sd0_clk: sd0-clk {
+ samsung,pins = "gpg-0";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ sd0_bus1: sd0-bus1 {
+ samsung,pins = "gpg-2";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ sd0_bus4: sd0-bus4 {
+ samsung,pins = "gpg-2", "gpg-3", "gpg-4", "gpg-5";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ sd0_cd: sd0-cd {
+ samsung,pins = "gpg-6";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_UP>;
+ };
+
+ sd1_cmd: sd1-cmd {
+ samsung,pins = "gph-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ sd1_clk: sd1-clk {
+ samsung,pins = "gph-0";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ sd1_bus1: sd1-bus1 {
+ samsung,pins = "gph-2";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ sd1_bus4: sd1-bus4 {
+ samsung,pins = "gph-2", "gph-3", "gph-4", "gph-5";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ sd1_bus8: sd1-bus8 {
+ samsung,pins = "gph-2", "gph-3", "gph-4", "gph-5",
+ "gph-6", "gph-7", "gph-8", "gph-9";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ sd1_cd: sd1-cd {
+ samsung,pins = "gpg-6";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_UP>;
+ };
+
+ sd2_cmd: sd2-cmd {
+ samsung,pins = "gpc-4";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ sd2_clk: sd2-clk {
+ samsung,pins = "gpc-5";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ sd2_bus1: sd2-bus1 {
+ samsung,pins = "gph-6";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ sd2_bus4: sd2-bus4 {
+ samsung,pins = "gph-6", "gph-7", "gph-8", "gph-9";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ i2s0_bus: i2s0-bus {
+ samsung,pins = "gpd-0", "gpd-2", "gpd-3", "gpd-4";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ i2s0_cdclk: i2s0-cdclk {
+ samsung,pins = "gpd-1";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ i2s1_bus: i2s1-bus {
+ samsung,pins = "gpe-0", "gpe-2", "gpe-3", "gpe-4";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ i2s1_cdclk: i2s1-cdclk {
+ samsung,pins = "gpe-1";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ i2s2_bus: i2s2-bus {
+ /* S3C6410-only */
+ samsung,pins = "gpc-4", "gpc-5", "gpc-6", "gph-6",
+ "gph-8", "gph-9";
+ samsung,pin-function = <5>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ i2s2_cdclk: i2s2-cdclk {
+ /* S3C6410-only */
+ samsung,pins = "gph-7";
+ samsung,pin-function = <5>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ pcm0_bus: pcm0-bus {
+ samsung,pins = "gpd-0", "gpd-2", "gpd-3", "gpd-4";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ pcm0_extclk: pcm0-extclk {
+ samsung,pins = "gpd-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ pcm1_bus: pcm1-bus {
+ samsung,pins = "gpe-0", "gpe-2", "gpe-3", "gpe-4";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ pcm1_extclk: pcm1-extclk {
+ samsung,pins = "gpe-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ ac97_bus_0: ac97-bus-0 {
+ samsung,pins = "gpd-0", "gpd-1", "gpd-2", "gpd-3", "gpd-4";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ ac97_bus_1: ac97-bus-1 {
+ samsung,pins = "gpe-0", "gpe-1", "gpe-2", "gpe-3", "gpe-4";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ cam_port: cam-port {
+ samsung,pins = "gpf-0", "gpf-1", "gpf-2", "gpf-4",
+ "gpf-5", "gpf-6", "gpf-7", "gpf-8",
+ "gpf-9", "gpf-10", "gpf-11", "gpf-12";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ cam_rst: cam-rst {
+ samsung,pins = "gpf-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ cam_field: cam-field {
+ /* S3C6410-only */
+ samsung,pins = "gpb-4";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ pwm_extclk: pwm-extclk {
+ samsung,pins = "gpf-13";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ pwm0_out: pwm0-out {
+ samsung,pins = "gpf-14";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ pwm1_out: pwm1-out {
+ samsung,pins = "gpf-15";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ clkout0: clkout-0 {
+ samsung,pins = "gpf-14";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_col0_0: keypad-col0-0 {
+ samsung,pins = "gph-0";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_col1_0: keypad-col1-0 {
+ samsung,pins = "gph-1";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_col2_0: keypad-col2-0 {
+ samsung,pins = "gph-2";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_col3_0: keypad-col3-0 {
+ samsung,pins = "gph-3";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_col4_0: keypad-col4-0 {
+ samsung,pins = "gph-4";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_col5_0: keypad-col5-0 {
+ samsung,pins = "gph-5";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_col6_0: keypad-col6-0 {
+ samsung,pins = "gph-6";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_col7_0: keypad-col7-0 {
+ samsung,pins = "gph-7";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_col0_1: keypad-col0-1 {
+ samsung,pins = "gpl-0";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_col1_1: keypad-col1-1 {
+ samsung,pins = "gpl-1";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_col2_1: keypad-col2-1 {
+ samsung,pins = "gpl-2";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_col3_1: keypad-col3-1 {
+ samsung,pins = "gpl-3";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_col4_1: keypad-col4-1 {
+ samsung,pins = "gpl-4";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_col5_1: keypad-col5-1 {
+ samsung,pins = "gpl-5";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_col6_1: keypad-col6-1 {
+ samsung,pins = "gpl-6";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_col7_1: keypad-col7-1 {
+ samsung,pins = "gpl-7";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_row0_0: keypad-row0-0 {
+ samsung,pins = "gpk-8";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_row1_0: keypad-row1-0 {
+ samsung,pins = "gpk-9";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_row2_0: keypad-row2-0 {
+ samsung,pins = "gpk-10";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_row3_0: keypad-row3-0 {
+ samsung,pins = "gpk-11";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_row4_0: keypad-row4-0 {
+ samsung,pins = "gpk-12";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_row5_0: keypad-row5-0 {
+ samsung,pins = "gpk-13";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_row6_0: keypad-row6-0 {
+ samsung,pins = "gpk-14";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_row7_0: keypad-row7-0 {
+ samsung,pins = "gpk-15";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_row0_1: keypad-row0-1 {
+ samsung,pins = "gpn-0";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_row1_1: keypad-row1-1 {
+ samsung,pins = "gpn-1";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_row2_1: keypad-row2-1 {
+ samsung,pins = "gpn-2";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_row3_1: keypad-row3-1 {
+ samsung,pins = "gpn-3";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_row4_1: keypad-row4-1 {
+ samsung,pins = "gpn-4";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_row5_1: keypad-row5-1 {
+ samsung,pins = "gpn-5";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_row6_1: keypad-row6-1 {
+ samsung,pins = "gpn-6";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ keypad_row7_1: keypad-row7-1 {
+ samsung,pins = "gpn-7";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ lcd_ctrl: lcd-ctrl {
+ samsung,pins = "gpj-8", "gpj-9", "gpj-10", "gpj-11";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ lcd_data16: lcd-data-width16 {
+ samsung,pins = "gpi-3", "gpi-4", "gpi-5", "gpi-6",
+ "gpi-7", "gpi-10", "gpi-11", "gpi-12",
+ "gpi-13", "gpi-14", "gpi-15", "gpj-3",
+ "gpj-4", "gpj-5", "gpj-6", "gpj-7";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ lcd_data18: lcd-data-width18 {
+ samsung,pins = "gpi-2", "gpi-3", "gpi-4", "gpi-5",
+ "gpi-6", "gpi-7", "gpi-10", "gpi-11",
+ "gpi-12", "gpi-13", "gpi-14", "gpi-15",
+ "gpj-2", "gpj-3", "gpj-4", "gpj-5",
+ "gpj-6", "gpj-7";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ lcd_data24: lcd-data-width24 {
+ samsung,pins = "gpi-0", "gpi-1", "gpi-2", "gpi-3",
+ "gpi-4", "gpi-5", "gpi-6", "gpi-7",
+ "gpi-8", "gpi-9", "gpi-10", "gpi-11",
+ "gpi-12", "gpi-13", "gpi-14", "gpi-15",
+ "gpj-0", "gpj-1", "gpj-2", "gpj-3",
+ "gpj-4", "gpj-5", "gpj-6", "gpj-7";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+
+ hsi_bus: hsi-bus {
+ samsung,pins = "gpk-0", "gpk-1", "gpk-2", "gpk-3",
+ "gpk-4", "gpk-5", "gpk-6", "gpk-7";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <PIN_PULL_NONE>;
+ };
+};
--- /dev/null
+/*
+ * Samsung's S3C64xx SoC series common device tree source
+ *
+ * Copyright (c) 2013 Tomasz Figa <tomasz.figa@gmail.com>
+ *
+ * Samsung's S3C64xx SoC series device nodes are listed in this file.
+ * Particular SoCs from S3C64xx series can include this file and provide
+ * values for SoCs specfic bindings.
+ *
+ * Note: This file does not include device nodes for all the controllers in
+ * S3C64xx SoCs. As device tree coverage for S3C64xx increases, additional
+ * nodes can be added to this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "skeleton.dtsi"
+#include <dt-bindings/clock/samsung,s3c64xx-clock.h>
+
+/ {
+ aliases {
+ i2c0 = &i2c0;
+ pinctrl0 = &pinctrl0;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,arm1176jzf-s", "arm,arm1176";
+ reg = <0x0>;
+ };
+ };
+
+ soc: soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ vic0: interrupt-controller@71200000 {
+ compatible = "arm,pl192-vic";
+ interrupt-controller;
+ reg = <0x71200000 0x1000>;
+ #interrupt-cells = <1>;
+ };
+
+ vic1: interrupt-controller@71300000 {
+ compatible = "arm,pl192-vic";
+ interrupt-controller;
+ reg = <0x71300000 0x1000>;
+ #interrupt-cells = <1>;
+ };
+
+ sdhci0: sdhci@7c200000 {
+ compatible = "samsung,s3c6410-sdhci";
+ reg = <0x7c200000 0x100>;
+ interrupt-parent = <&vic1>;
+ interrupts = <24>;
+ clock-names = "hsmmc", "mmc_busclk.0", "mmc_busclk.2";
+ clocks = <&clocks HCLK_HSMMC0>, <&clocks HCLK_HSMMC0>,
+ <&clocks SCLK_MMC0>;
+ status = "disabled";
+ };
+
+ sdhci1: sdhci@7c300000 {
+ compatible = "samsung,s3c6410-sdhci";
+ reg = <0x7c300000 0x100>;
+ interrupt-parent = <&vic1>;
+ interrupts = <25>;
+ clock-names = "hsmmc", "mmc_busclk.0", "mmc_busclk.2";
+ clocks = <&clocks HCLK_HSMMC1>, <&clocks HCLK_HSMMC1>,
+ <&clocks SCLK_MMC1>;
+ status = "disabled";
+ };
+
+ sdhci2: sdhci@7c400000 {
+ compatible = "samsung,s3c6410-sdhci";
+ reg = <0x7c400000 0x100>;
+ interrupt-parent = <&vic1>;
+ interrupts = <17>;
+ clock-names = "hsmmc", "mmc_busclk.0", "mmc_busclk.2";
+ clocks = <&clocks HCLK_HSMMC2>, <&clocks HCLK_HSMMC2>,
+ <&clocks SCLK_MMC2>;
+ status = "disabled";
+ };
+
+ watchdog: watchdog@7e004000 {
+ compatible = "samsung,s3c2410-wdt";
+ reg = <0x7e004000 0x1000>;
+ interrupt-parent = <&vic0>;
+ interrupts = <26>;
+ clock-names = "watchdog";
+ clocks = <&clocks PCLK_WDT>;
+ status = "disabled";
+ };
+
+ i2c0: i2c@7f004000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x7f004000 0x1000>;
+ interrupt-parent = <&vic1>;
+ interrupts = <18>;
+ clock-names = "i2c";
+ clocks = <&clocks PCLK_IIC0>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ uart0: serial@7f005000 {
+ compatible = "samsung,s3c6400-uart";
+ reg = <0x7f005000 0x100>;
+ interrupt-parent = <&vic1>;
+ interrupts = <5>;
+ clock-names = "uart", "clk_uart_baud2",
+ "clk_uart_baud3";
+ clocks = <&clocks PCLK_UART0>, <&clocks PCLK_UART0>,
+ <&clocks SCLK_UART>;
+ status = "disabled";
+ };
+
+ uart1: serial@7f005400 {
+ compatible = "samsung,s3c6400-uart";
+ reg = <0x7f005400 0x100>;
+ interrupt-parent = <&vic1>;
+ interrupts = <6>;
+ clock-names = "uart", "clk_uart_baud2",
+ "clk_uart_baud3";
+ clocks = <&clocks PCLK_UART1>, <&clocks PCLK_UART1>,
+ <&clocks SCLK_UART>;
+ status = "disabled";
+ };
+
+ uart2: serial@7f005800 {
+ compatible = "samsung,s3c6400-uart";
+ reg = <0x7f005800 0x100>;
+ interrupt-parent = <&vic1>;
+ interrupts = <7>;
+ clock-names = "uart", "clk_uart_baud2",
+ "clk_uart_baud3";
+ clocks = <&clocks PCLK_UART2>, <&clocks PCLK_UART2>,
+ <&clocks SCLK_UART>;
+ status = "disabled";
+ };
+
+ uart3: serial@7f005c00 {
+ compatible = "samsung,s3c6400-uart";
+ reg = <0x7f005c00 0x100>;
+ interrupt-parent = <&vic1>;
+ interrupts = <8>;
+ clock-names = "uart", "clk_uart_baud2",
+ "clk_uart_baud3";
+ clocks = <&clocks PCLK_UART3>, <&clocks PCLK_UART3>,
+ <&clocks SCLK_UART>;
+ status = "disabled";
+ };
+
+ pwm: pwm@7f006000 {
+ compatible = "samsung,s3c6400-pwm";
+ reg = <0x7f006000 0x1000>;
+ interrupt-parent = <&vic0>;
+ interrupts = <23>, <24>, <25>, <27>, <28>;
+ clock-names = "timers";
+ clocks = <&clocks PCLK_PWM>;
+ samsung,pwm-outputs = <0>, <1>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ pinctrl0: pinctrl@7f008000 {
+ compatible = "samsung,s3c64xx-pinctrl";
+ reg = <0x7f008000 0x1000>;
+ interrupt-parent = <&vic1>;
+ interrupts = <21>;
+
+ pctrl_int_map: pinctrl-interrupt-map {
+ interrupt-map = <0 &vic0 0>,
+ <1 &vic0 1>,
+ <2 &vic1 0>,
+ <3 &vic1 1>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #interrupt-cells = <1>;
+ };
+
+ wakeup-interrupt-controller {
+ compatible = "samsung,s3c64xx-wakeup-eint";
+ interrupts = <0>, <1>, <2>, <3>;
+ interrupt-parent = <&pctrl_int_map>;
+ };
+ };
+ };
+};
+
+#include "s3c64xx-pinctrl.dtsi"
*/
#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/mfd/dbx500-prcmu.h>
#include "skeleton.dtsi"
/ {
interrupts = <0 7 IRQ_TYPE_LEVEL_HIGH>;
};
+
+ clocks {
+ compatible = "stericsson,u8500-clks";
+
+ prcmu_clk: prcmu-clock {
+ #clock-cells = <1>;
+ };
+
+ prcc_pclk: prcc-periph-clock {
+ #clock-cells = <2>;
+ };
+
+ prcc_kclk: prcc-kernel-clock {
+ #clock-cells = <2>;
+ };
+
+ rtc_clk: rtc32k-clock {
+ #clock-cells = <0>;
+ };
+
+ smp_twd_clk: smp-twd-clock {
+ #clock-cells = <0>;
+ };
+ };
+
+ mtu@a03c6000 {
+ /* Nomadik System Timer */
+ compatible = "st,nomadik-mtu";
+ reg = <0xa03c6000 0x1000>;
+ interrupts = <0 4 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&prcmu_clk PRCMU_TIMCLK>, <&prcc_pclk 6 6>;
+ clock-names = "timclk", "apb_pclk";
+ };
+
timer@a0410600 {
compatible = "arm,cortex-a9-twd-timer";
reg = <0xa0410600 0x20>;
interrupts = <1 13 0x304>; /* IRQ level high per-CPU */
+
+ clocks = <&smp_twd_clk>;
};
rtc@80154000 {
compatible = "arm,rtc-pl031", "arm,primecell";
reg = <0x80154000 0x1000>;
interrupts = <0 18 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&rtc_clk>;
+ clock-names = "apb_pclk";
};
gpio0: gpio@8012e000 {
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <0>;
+
+ clocks = <&prcc_pclk 1 9>;
};
gpio1: gpio@8012e080 {
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <1>;
+
+ clocks = <&prcc_pclk 1 9>;
};
gpio2: gpio@8000e000 {
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <2>;
+
+ clocks = <&prcc_pclk 3 8>;
};
gpio3: gpio@8000e080 {
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <3>;
+
+ clocks = <&prcc_pclk 3 8>;
};
gpio4: gpio@8000e100 {
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <4>;
+
+ clocks = <&prcc_pclk 3 8>;
};
gpio5: gpio@8000e180 {
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <5>;
+
+ clocks = <&prcc_pclk 3 8>;
};
gpio6: gpio@8011e000 {
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <6>;
+
+ clocks = <&prcc_pclk 2 1>;
};
gpio7: gpio@8011e080 {
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <7>;
+
+ clocks = <&prcc_pclk 2 1>;
};
gpio8: gpio@a03fe000 {
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <8>;
+
+ clocks = <&prcc_pclk 6 1>;
};
pinctrl {
};
usb_per5@a03e0000 {
- compatible = "stericsson,db8500-musb",
- "mentor,musb";
+ compatible = "stericsson,db8500-musb";
reg = <0xa03e0000 0x10000>;
interrupts = <0 23 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "mc";
"iep_6_14", "oep_6_14",
"iep_7_15", "oep_7_15",
"iep_8", "oep_8";
+
+ clocks = <&prcc_pclk 5 0>;
};
dma: dma-controller@801C0000 {
#dma-cells = <3>;
memcpy-channels = <56 57 58 59 60>;
+
+ clocks = <&prcmu_clk PRCMU_DMACLK>;
};
prcmu: prcmu@80157000 {
reg = <0x80157450 0xC>;
};
+ cpufreq {
+ compatible = "stericsson,cpufreq-ux500";
+ clocks = <&prcmu_clk PRCMU_ARMSS>;
+ clock-names = "armss";
+ status = "disabled";
+ };
+
thermal@801573c0 {
compatible = "stericsson,db8500-thermal";
reg = <0x801573c0 0x40>;
compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
reg = <0x80004000 0x1000>;
interrupts = <0 21 IRQ_TYPE_LEVEL_HIGH>;
- arm,primecell-periphid = <0x180024>;
#address-cells = <1>;
#size-cells = <0>;
v-i2c-supply = <&db8500_vape_reg>;
clock-frequency = <400000>;
+ clocks = <&prcc_kclk 3 3>, <&prcc_pclk 3 3>;
+ clock-names = "i2cclk", "apb_pclk";
};
i2c@80122000 {
compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
reg = <0x80122000 0x1000>;
interrupts = <0 22 IRQ_TYPE_LEVEL_HIGH>;
- arm,primecell-periphid = <0x180024>;
#address-cells = <1>;
#size-cells = <0>;
v-i2c-supply = <&db8500_vape_reg>;
clock-frequency = <400000>;
+
+ clocks = <&prcc_kclk 1 2>, <&prcc_pclk 1 2>;
+ clock-names = "i2cclk", "apb_pclk";
};
i2c@80128000 {
compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
reg = <0x80128000 0x1000>;
interrupts = <0 55 IRQ_TYPE_LEVEL_HIGH>;
- arm,primecell-periphid = <0x180024>;
#address-cells = <1>;
#size-cells = <0>;
v-i2c-supply = <&db8500_vape_reg>;
clock-frequency = <400000>;
+
+ clocks = <&prcc_kclk 1 6>, <&prcc_pclk 1 6>;
+ clock-names = "i2cclk", "apb_pclk";
};
i2c@80110000 {
compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
reg = <0x80110000 0x1000>;
interrupts = <0 12 IRQ_TYPE_LEVEL_HIGH>;
- arm,primecell-periphid = <0x180024>;
#address-cells = <1>;
#size-cells = <0>;
v-i2c-supply = <&db8500_vape_reg>;
clock-frequency = <400000>;
+
+ clocks = <&prcc_kclk 2 0>, <&prcc_pclk 2 0>;
+ clock-names = "i2cclk", "apb_pclk";
};
i2c@8012a000 {
compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
reg = <0x8012a000 0x1000>;
interrupts = <0 51 IRQ_TYPE_LEVEL_HIGH>;
- arm,primecell-periphid = <0x180024>;
#address-cells = <1>;
#size-cells = <0>;
v-i2c-supply = <&db8500_vape_reg>;
clock-frequency = <400000>;
+
+ clocks = <&prcc_kclk 1 9>, <&prcc_pclk 1 9>;
+ clock-names = "i2cclk", "apb_pclk";
};
ssp@80002000 {
<&dma 13 0 0x0>; /* Logical - MemToDev */
dma-names = "rx", "tx";
+ clocks = <&prcc_kclk 1 0>, <&prcc_pclk 1 0>;
+ clock-names = "uart", "apb_pclk";
+
status = "disabled";
};
<&dma 12 0 0x0>; /* Logical - MemToDev */
dma-names = "rx", "tx";
+ clocks = <&prcc_kclk 1 1>, <&prcc_pclk 1 1>;
+ clock-names = "uart", "apb_pclk";
+
status = "disabled";
};
<&dma 11 0 0x0>; /* Logical - MemToDev */
dma-names = "rx", "tx";
+ clocks = <&prcc_kclk 3 6>, <&prcc_pclk 3 6>;
+ clock-names = "uart", "apb_pclk";
+
status = "disabled";
};
<&dma 29 0 0x0>; /* Logical - MemToDev */
dma-names = "rx", "tx";
+ clocks = <&prcc_kclk 1 5>, <&prcc_pclk 1 5>;
+ clock-names = "sdi", "apb_pclk";
+
status = "disabled";
};
<&dma 32 0 0x0>; /* Logical - MemToDev */
dma-names = "rx", "tx";
+ clocks = <&prcc_kclk 2 4>, <&prcc_pclk 2 6>;
+ clock-names = "sdi", "apb_pclk";
+
status = "disabled";
};
<&dma 28 0 0x0>; /* Logical - MemToDev */
dma-names = "rx", "tx";
+ clocks = <&prcc_kclk 3 4>, <&prcc_pclk 3 4>;
+ clock-names = "sdi", "apb_pclk";
+
status = "disabled";
};
compatible = "arm,pl18x", "arm,primecell";
reg = <0x80119000 0x1000>;
interrupts = <0 59 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&prcc_kclk 2 5>, <&prcc_pclk 2 7>;
+ clock-names = "sdi", "apb_pclk";
+
status = "disabled";
};
<&dma 42 0 0x0>; /* Logical - MemToDev */
dma-names = "rx", "tx";
+ clocks = <&prcc_kclk 2 2>, <&prcc_pclk 2 4>;
+ clock-names = "sdi", "apb_pclk";
+
status = "disabled";
};
compatible = "arm,pl18x", "arm,primecell";
reg = <0x80008000 0x1000>;
interrupts = <0 100 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&prcc_kclk 3 7>, <&prcc_pclk 3 7>;
+ clock-names = "sdi", "apb_pclk";
+
status = "disabled";
};
reg = <0x80123000 0x1000>;
interrupts = <0 31 IRQ_TYPE_LEVEL_HIGH>;
v-ape-supply = <&db8500_vape_reg>;
+
+ clocks = <&prcc_kclk 1 3>, <&prcc_pclk 1 3>;
+ clock-names = "msp", "apb_pclk";
+
status = "disabled";
};
reg = <0x80124000 0x1000>;
interrupts = <0 62 IRQ_TYPE_LEVEL_HIGH>;
v-ape-supply = <&db8500_vape_reg>;
+
+ clocks = <&prcc_kclk 1 4>, <&prcc_pclk 1 4>;
+ clock-names = "msp", "apb_pclk";
+
status = "disabled";
};
reg = <0x80117000 0x1000>;
interrupts = <0 98 IRQ_TYPE_LEVEL_HIGH>;
v-ape-supply = <&db8500_vape_reg>;
+
+ clocks = <&prcc_kclk 2 3>, <&prcc_pclk 2 5>;
+ clock-names = "msp", "apb_pclk";
+
status = "disabled";
};
reg = <0x80125000 0x1000>;
interrupts = <0 62 IRQ_TYPE_LEVEL_HIGH>;
v-ape-supply = <&db8500_vape_reg>;
+
+ clocks = <&prcc_kclk 1 10>, <&prcc_pclk 1 11>;
+ clock-names = "msp", "apb_pclk";
+
status = "disabled";
};
cpufreq-cooling {
compatible = "stericsson,db8500-cpufreq-cooling";
status = "disabled";
- };
+ };
vmmci: regulator-gpio {
compatible = "regulator-gpio";
interrupts = <0 15 IRQ_TYPE_LEVEL_HIGH>;
v-ape-supply = <&db8500_vape_reg>;
+ clocks = <&prcc_pclk 6 1>;
};
hash@a03c2000 {
reg = <0xa03c2000 0x1000>;
v-ape-supply = <&db8500_vape_reg>;
+ clocks = <&prcc_pclk 6 2>;
};
};
};
bu21013_tp@5c {
compatible = "rohm,bu21013_tp";
reg = <0x5c>;
- touch-gpio = <&gpio2 20 0x4>;
avdd-supply = <&ab8500_ldo_aux1_reg>;
rohm,touch-max-x = <384>;
bu21013_tp@5d {
compatible = "rohm,bu21013_tp";
reg = <0x5d>;
- touch-gpio = <&gpio2 20 0x4>;
avdd-supply = <&ab8500_ldo_aux1_reg>;
rohm,touch-max-x = <384>;
--- /dev/null
+/*
+ * Copyright 2012 ST-Ericsson AB
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ *
+ * Device Tree for the TVK1281618 UIB
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ soc {
+ /* Add Synaptics touch screen, TC35892 keypad etc here */
+ i2c@80004000 {
+ tc3589x@44 {
+ compatible = "tc3589x";
+ reg = <0x44>;
+ interrupt-parent = <&gpio6>;
+ interrupts = <26 IRQ_TYPE_EDGE_RISING>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ tc3589x_gpio {
+ compatible = "tc3589x-gpio";
+ interrupts = <0 IRQ_TYPE_EDGE_RISING>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+ };
+ };
+ };
+};
status = "okay";
};
- i2c@80004000 {
- tc3589x@42 {
- compatible = "tc3589x";
- reg = <0x42>;
- interrupt-parent = <&gpio6>;
- interrupts = <25 IRQ_TYPE_EDGE_RISING>;
-
- interrupt-controller;
- #interrupt-cells = <2>;
-
- tc3589x_gpio: tc3589x_gpio {
- compatible = "tc3589x-gpio";
- interrupts = <0 IRQ_TYPE_EDGE_RISING>;
-
- interrupt-controller;
- #interrupt-cells = <2>;
- gpio-controller;
- #gpio-cells = <2>;
- };
- };
- };
-
i2c@80128000 {
lp5521@33 {
compatible = "national,lp5521";
chan0 {
led-cur = /bits/ 8 <0x2f>;
max-cur = /bits/ 8 <0x5f>;
+ linux,default-trigger = "heartbeat";
};
chan1 {
led-cur = /bits/ 8 <0x2f>;
};
bh1780@29 {
compatible = "rohm,bh1780gli";
- reg = <0x33>;
+ reg = <0x29>;
};
};
};
prcmu@80157000 {
- db8500-prcmu-regulators {
- db8500_vape_reg: db8500_vape {
- regulator-name = "db8500-vape";
- };
-
- db8500_varm_reg: db8500_varm {
- regulator-name = "db8500-varm";
- };
-
- db8500_vmodem_reg: db8500_vmodem {
- regulator-name = "db8500-vmodem";
- };
-
- db8500_vpll_reg: db8500_vpll {
- regulator-name = "db8500-vpll";
- };
-
- db8500_vsmps1_reg: db8500_vsmps1 {
- regulator-name = "db8500-vsmps1";
- };
-
- db8500_vsmps2_reg: db8500_vsmps2 {
- regulator-name = "db8500-vsmps2";
- };
-
- db8500_vsmps3_reg: db8500_vsmps3 {
- regulator-name = "db8500-vsmps3";
- };
-
- db8500_vrf1_reg: db8500_vrf1 {
- regulator-name = "db8500-vrf1";
- };
-
- db8500_sva_mmdsp_reg: db8500_sva_mmdsp {
- regulator-name = "db8500-sva-mmdsp";
- };
-
- db8500_sva_mmdsp_ret_reg: db8500_sva_mmdsp_ret {
- regulator-name = "db8500-sva-mmdsp-ret";
- };
-
- db8500_sva_pipe_reg: db8500_sva_pipe {
- regulator-name = "db8500_sva_pipe";
- };
-
- db8500_sia_mmdsp_reg: db8500_sia_mmdsp {
- regulator-name = "db8500_sia_mmdsp";
- };
-
- db8500_sia_mmdsp_ret_reg: db8500_sia_mmdsp_ret {
- regulator-name = "db8500-sia-mmdsp-ret";
- };
-
- db8500_sia_pipe_reg: db8500_sia_pipe {
- regulator-name = "db8500-sia-pipe";
- };
-
- db8500_sga_reg: db8500_sga {
- regulator-name = "db8500-sga";
- };
-
- db8500_b2r2_mcde_reg: db8500_b2r2_mcde {
- regulator-name = "db8500-b2r2-mcde";
- };
-
- db8500_esram12_reg: db8500_esram12 {
- regulator-name = "db8500-esram12";
- };
-
- db8500_esram12_ret_reg: db8500_esram12_ret {
- regulator-name = "db8500-esram12-ret";
- };
-
- db8500_esram34_reg: db8500_esram34 {
- regulator-name = "db8500-esram34";
+ ab8500 {
+ ab8500-gpio {
+ compatible = "stericsson,ab8500-gpio";
};
- db8500_esram34_ret_reg: db8500_esram34_ret {
- regulator-name = "db8500-esram34-ret";
- };
- };
-
- ab8500 {
ab8500-regulators {
ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
regulator-name = "V-DISPLAY";
--- /dev/null
+/*
+ * Copyright 2012 ST-Ericsson AB
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "ste-hrefprev60.dtsi"
+#include "ste-href-stuib.dtsi"
+
+/ {
+ model = "ST-Ericsson HREF (pre-v60) and ST UIB";
+ compatible = "st-ericsson,mop500", "st-ericsson,u8500";
+
+ soc {
+ /* Reset line for the BU21013 touchscreen */
+ i2c@80110000 {
+ /* Only one of these will be used */
+ bu21013_tp@5c {
+ touch-gpio = <&gpio2 12 0x4>;
+ reset-gpio = <&tc3589x_gpio 13 0x4>;
+ };
+ bu21013_tp@5d {
+ touch-gpio = <&gpio2 12 0x4>;
+ reset-gpio = <&tc3589x_gpio 13 0x4>;
+ };
+ };
+ };
+};
--- /dev/null
+/*
+ * Copyright 2012 ST-Ericsson AB
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "ste-hrefprev60.dtsi"
+#include "ste-href-tvk1281618.dtsi"
+
+/ {
+ model = "ST-Ericsson HREF (pre-v60) and TVK1281618 UIB";
+ compatible = "st-ericsson,mop500", "st-ericsson,u8500";
+};
*
* http://www.opensource.org/licenses/gpl-license.html
* http://www.gnu.org/copyleft/gpl.html
+ *
+ * Device Tree for the HREF+ prior to the v60 variant.
*/
-/dts-v1/;
#include "ste-dbx5x0.dtsi"
#include "ste-href.dtsi"
-#include "ste-stuib.dtsi"
/ {
- model = "ST-Ericsson HREF (pre-v60) platform with Device Tree";
- compatible = "st-ericsson,mop500", "st-ericsson,u8500";
-
gpio_keys {
button@1 {
gpios = <&tc3589x_gpio 7 0x4>;
};
soc {
- prcmu@80157000 {
- ab8500@5 {
- ab8500-gpio {
- compatible = "stericsson,ab8500-gpio";
- };
- };
- };
-
i2c@80004000 {
tps61052@33 {
compatible = "tps61052";
reg = <0x33>;
};
- };
- i2c@80110000 {
- bu21013_tp@5c {
- reset-gpio = <&tc3589x_gpio 13 0x4>;
+ tc3589x@42 {
+ compatible = "tc3589x";
+ reg = <0x42>;
+ interrupt-parent = <&gpio6>;
+ interrupts = <25 IRQ_TYPE_EDGE_RISING>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ tc3589x_gpio: tc3589x_gpio {
+ compatible = "tc3589x-gpio";
+ interrupts = <0 IRQ_TYPE_EDGE_RISING>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
};
};
--- /dev/null
+/*
+ * Copyright 2012 ST-Ericsson AB
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ *
+ * Device Tree for the HREF version 60 or later with the ST UIB
+ */
+
+/dts-v1/;
+#include "ste-hrefv60plus.dtsi"
+#include "ste-href-stuib.dtsi"
+
+/ {
+ model = "ST-Ericsson HREF (v60+) and ST UIB";
+ compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500";
+
+ soc {
+ /* Reset line for the BU21013 touchscreen */
+ i2c@80110000 {
+ /* Only one of these will be used */
+ bu21013_tp@5c {
+ touch-gpio = <&gpio2 20 0x4>;
+ reset-gpio = <&gpio4 17 0x4>;
+ };
+ bu21013_tp@5d {
+ touch-gpio = <&gpio2 20 0x4>;
+ reset-gpio = <&gpio4 17 0x4>;
+ };
+ };
+ };
+};
--- /dev/null
+/*
+ * Copyright 2012 ST-Ericsson AB
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ *
+ * Device Tree for the HREF version 60 or later with the TVK1281618 UIB
+ */
+
+/dts-v1/;
+#include "ste-hrefv60plus.dtsi"
+#include "ste-href-tvk1281618.dtsi"
+
+/ {
+ model = "ST-Ericsson HREF (v60+) and TVK1281618 UIB";
+ compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500";
+};
+++ /dev/null
-/*
- * Copyright 2012 ST-Ericsson AB
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 or later at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
- */
-
-/dts-v1/;
-#include "ste-dbx5x0.dtsi"
-#include "ste-href.dtsi"
-#include "ste-stuib.dtsi"
-
-/ {
- model = "ST-Ericsson HREF (v60+) platform with Device Tree";
- compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500";
-
- gpio_keys {
- button@1 {
- gpios = <&gpio6 25 0x4>;
- };
- };
-
- soc {
- i2c@80110000 {
- bu21013_tp@0x5c {
- reset-gpio = <&gpio4 15 0x4>;
- };
- };
-
- // External Micro SD slot
- sdi0_per1@80126000 {
- arm,primecell-periphid = <0x10480180>;
- max-frequency = <100000000>;
- bus-width = <4>;
- mmc-cap-sd-highspeed;
- mmc-cap-mmc-highspeed;
- vmmc-supply = <&ab8500_ldo_aux3_reg>;
-
- cd-gpios = <&tc3589x_gpio 3 0x4>;
-
- status = "okay";
- };
-
- // WLAN SDIO channel
- sdi1_per2@80118000 {
- arm,primecell-periphid = <0x10480180>;
- max-frequency = <100000000>;
- bus-width = <4>;
-
- status = "okay";
- };
-
- // PoP:ed eMMC
- sdi2_per3@80005000 {
- arm,primecell-periphid = <0x10480180>;
- max-frequency = <100000000>;
- bus-width = <8>;
- mmc-cap-mmc-highspeed;
-
- status = "okay";
- };
-
- // On-board eMMC
- sdi4_per2@80114000 {
- arm,primecell-periphid = <0x10480180>;
- max-frequency = <100000000>;
- bus-width = <8>;
- mmc-cap-mmc-highspeed;
- vmmc-supply = <&ab8500_ldo_aux2_reg>;
-
- status = "okay";
- };
-
- prcmu@80157000 {
- db8500-prcmu-regulators {
- db8500_vape_reg: db8500_vape {
- regulator-name = "db8500-vape";
- };
-
- db8500_varm_reg: db8500_varm {
- regulator-name = "db8500-varm";
- };
-
- db8500_vmodem_reg: db8500_vmodem {
- regulator-name = "db8500-vmodem";
- };
-
- db8500_vpll_reg: db8500_vpll {
- regulator-name = "db8500-vpll";
- };
-
- db8500_vsmps1_reg: db8500_vsmps1 {
- regulator-name = "db8500-vsmps1";
- };
-
- db8500_vsmps2_reg: db8500_vsmps2 {
- regulator-name = "db8500-vsmps2";
- };
-
- db8500_vsmps3_reg: db8500_vsmps3 {
- regulator-name = "db8500-vsmps3";
- };
-
- db8500_vrf1_reg: db8500_vrf1 {
- regulator-name = "db8500-vrf1";
- };
-
- db8500_sva_mmdsp_reg: db8500_sva_mmdsp {
- regulator-name = "db8500-sva-mmdsp";
- };
-
- db8500_sva_mmdsp_ret_reg: db8500_sva_mmdsp_ret {
- regulator-name = "db8500-sva-mmdsp-ret";
- };
-
- db8500_sva_pipe_reg: db8500_sva_pipe {
- regulator-name = "db8500_sva_pipe";
- };
-
- db8500_sia_mmdsp_reg: db8500_sia_mmdsp {
- regulator-name = "db8500_sia_mmdsp";
- };
-
- db8500_sia_mmdsp_ret_reg: db8500_sia_mmdsp_ret {
- regulator-name = "db8500-sia-mmdsp-ret";
- };
-
- db8500_sia_pipe_reg: db8500_sia_pipe {
- regulator-name = "db8500-sia-pipe";
- };
-
- db8500_sga_reg: db8500_sga {
- regulator-name = "db8500-sga";
- };
-
- db8500_b2r2_mcde_reg: db8500_b2r2_mcde {
- regulator-name = "db8500-b2r2-mcde";
- };
-
- db8500_esram12_reg: db8500_esram12 {
- regulator-name = "db8500-esram12";
- };
-
- db8500_esram12_ret_reg: db8500_esram12_ret {
- regulator-name = "db8500-esram12-ret";
- };
-
- db8500_esram34_reg: db8500_esram34 {
- regulator-name = "db8500-esram34";
- };
-
- db8500_esram34_ret_reg: db8500_esram34_ret {
- regulator-name = "db8500-esram34-ret";
- };
- };
-
- ab8500 {
- ab8500-regulators {
- ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
- regulator-name = "V-DISPLAY";
- };
-
- ab8500_ldo_aux2_reg: ab8500_ldo_aux2 {
- regulator-name = "V-eMMC1";
- };
-
- ab8500_ldo_aux3_reg: ab8500_ldo_aux3 {
- regulator-name = "V-MMC-SD";
- };
-
- ab8500_ldo_intcore_reg: ab8500_ldo_intcore {
- regulator-name = "V-INTCORE";
- };
-
- ab8500_ldo_tvout_reg: ab8500_ldo_tvout {
- regulator-name = "V-TVOUT";
- };
-
- ab8500_ldo_usb_reg: ab8500_ldo_usb {
- regulator-name = "dummy";
- };
-
- ab8500_ldo_audio_reg: ab8500_ldo_audio {
- regulator-name = "V-AUD";
- };
-
- ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 {
- regulator-name = "V-AMIC1";
- };
-
- ab8500_ldo_anamic2_reg: ab8500_ldo_anamic2 {
- regulator-name = "V-AMIC2";
- };
-
- ab8500_ldo_dmic_reg: ab8500_ldo_dmic {
- regulator-name = "V-DMIC";
- };
-
- ab8500_ldo_ana_reg: ab8500_ldo_ana {
- regulator-name = "V-CSI/DSI";
- };
- };
- };
- };
- };
-};
--- /dev/null
+/*
+ * Copyright 2012 ST-Ericsson AB
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include "ste-dbx5x0.dtsi"
+#include "ste-href.dtsi"
+
+/ {
+ model = "ST-Ericsson HREF (v60+) platform with Device Tree";
+ compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500";
+
+ gpio_keys {
+ button@1 {
+ gpios = <&gpio5 25 0x4>;
+ };
+ };
+
+ soc {
+ // External Micro SD slot
+ sdi0_per1@80126000 {
+ arm,primecell-periphid = <0x10480180>;
+ max-frequency = <100000000>;
+ bus-width = <4>;
+ mmc-cap-sd-highspeed;
+ mmc-cap-mmc-highspeed;
+ vmmc-supply = <&ab8500_ldo_aux3_reg>;
+
+ cd-gpios = <&gpio2 31 0x4>; // 95
+
+ status = "okay";
+ };
+
+ // WLAN SDIO channel
+ sdi1_per2@80118000 {
+ arm,primecell-periphid = <0x10480180>;
+ max-frequency = <100000000>;
+ bus-width = <4>;
+
+ status = "okay";
+ };
+
+ // PoP:ed eMMC
+ sdi2_per3@80005000 {
+ arm,primecell-periphid = <0x10480180>;
+ max-frequency = <100000000>;
+ bus-width = <8>;
+ mmc-cap-mmc-highspeed;
+
+ status = "okay";
+ };
+
+ // On-board eMMC
+ sdi4_per2@80114000 {
+ arm,primecell-periphid = <0x10480180>;
+ max-frequency = <100000000>;
+ bus-width = <8>;
+ mmc-cap-mmc-highspeed;
+ vmmc-supply = <&ab8500_ldo_aux2_reg>;
+
+ status = "okay";
+ };
+ };
+};
reg-names = "fsmc_regs", "nand_data", "nand_addr", "nand_cmd";
clocks = <&hclksmc>;
status = "okay";
+ timings = /bits/ 8 <0 0 0 0x10 0x0a 0>;
partition@0 {
label = "X-Loader(NAND)";
pinctrl-0 = <&i2c0_default_mux>, <&i2c0_default_mode>;
stw4811@2d {
- compatible = "st,stw4811";
- reg = <0x2d>;
+ compatible = "st,stw4811";
+ reg = <0x2d>;
+ vmmc_regulator: vmmc {
+ compatible = "st,stw481x-vmmc";
+ regulator-name = "VMMC";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
};
};
cd-inverted;
pinctrl-names = "default";
pinctrl-0 = <&mmcsd_default_mux>, <&mmcsd_default_mode>;
+ vmmc-supply = <&vmmc_regulator>;
};
};
};
vdd33a-supply = <&en_3v3_reg>;
vddvario-supply = <&db8500_vape_reg>;
-
reg-shift = <1>;
reg-io-width = <2>;
smsc,force-internal-phy;
smsc,irq-active-high;
smsc,irq-push-pull;
+
+ clocks = <&prcc_pclk 3 0>;
};
};
};
prcmu@80157000 {
- db8500-prcmu-regulators {
- db8500_vape_reg: db8500_vape {
- regulator-name = "db8500-vape";
- };
-
- db8500_varm_reg: db8500_varm {
- regulator-name = "db8500-varm";
- };
-
- db8500_vmodem_reg: db8500_vmodem {
- regulator-name = "db8500-vmodem";
- };
-
- db8500_vpll_reg: db8500_vpll {
- regulator-name = "db8500-vpll";
- };
-
- db8500_vsmps1_reg: db8500_vsmps1 {
- regulator-name = "db8500-vsmps1";
- };
-
- db8500_vsmps2_reg: db8500_vsmps2 {
- regulator-name = "db8500-vsmps2";
- };
-
- db8500_vsmps3_reg: db8500_vsmps3 {
- regulator-name = "db8500-vsmps3";
- };
-
- db8500_vrf1_reg: db8500_vrf1 {
- regulator-name = "db8500-vrf1";
- };
-
- db8500_sva_mmdsp_reg: db8500_sva_mmdsp {
- regulator-name = "db8500-sva-mmdsp";
- };
-
- db8500_sva_mmdsp_ret_reg: db8500_sva_mmdsp_ret {
- regulator-name = "db8500-sva-mmdsp-ret";
- };
-
- db8500_sva_pipe_reg: db8500_sva_pipe {
- regulator-name = "db8500_sva_pipe";
- };
-
- db8500_sia_mmdsp_reg: db8500_sia_mmdsp {
- regulator-name = "db8500_sia_mmdsp";
- };
-
- db8500_sia_mmdsp_ret_reg: db8500_sia_mmdsp_ret {
- regulator-name = "db8500-sia-mmdsp-ret";
- };
-
- db8500_sia_pipe_reg: db8500_sia_pipe {
- regulator-name = "db8500-sia-pipe";
- };
-
- db8500_sga_reg: db8500_sga {
- regulator-name = "db8500-sga";
- };
-
- db8500_b2r2_mcde_reg: db8500_b2r2_mcde {
- regulator-name = "db8500-b2r2-mcde";
- };
-
- db8500_esram12_reg: db8500_esram12 {
- regulator-name = "db8500-esram12";
- };
-
- db8500_esram12_ret_reg: db8500_esram12_ret {
- regulator-name = "db8500-esram12-ret";
- };
-
- db8500_esram34_reg: db8500_esram34 {
- regulator-name = "db8500-esram34";
- };
-
- db8500_esram34_ret_reg: db8500_esram34_ret {
- regulator-name = "db8500-esram34-ret";
- };
+ cpufreq {
+ status = "okay";
};
thermal@801573c0 {
obj-$(CONFIG_ICST) += icst.o
obj-$(CONFIG_SA1111) += sa1111.o
-obj-$(CONFIG_PCI_HOST_VIA82C505) += via82c505.o
obj-$(CONFIG_DMABOUNCE) += dmabounce.o
obj-$(CONFIG_SHARP_LOCOMO) += locomo.o
obj-$(CONFIG_SHARP_PARAM) += sharpsl_param.o
+++ /dev/null
-#include <linux/kernel.h>
-#include <linux/pci.h>
-#include <linux/interrupt.h>
-#include <linux/mm.h>
-#include <linux/init.h>
-#include <linux/ioport.h>
-#include <linux/io.h>
-
-
-#include <asm/mach/pci.h>
-
-#define MAX_SLOTS 7
-
-#define CONFIG_CMD(bus, devfn, where) (0x80000000 | (bus->number << 16) | (devfn << 8) | (where & ~3))
-
-static int
-via82c505_read_config(struct pci_bus *bus, unsigned int devfn, int where,
- int size, u32 *value)
-{
- outl(CONFIG_CMD(bus,devfn,where),0xCF8);
- switch (size) {
- case 1:
- *value=inb(0xCFC + (where&3));
- break;
- case 2:
- *value=inw(0xCFC + (where&2));
- break;
- case 4:
- *value=inl(0xCFC);
- break;
- }
- return PCIBIOS_SUCCESSFUL;
-}
-
-static int
-via82c505_write_config(struct pci_bus *bus, unsigned int devfn, int where,
- int size, u32 value)
-{
- outl(CONFIG_CMD(bus,devfn,where),0xCF8);
- switch (size) {
- case 1:
- outb(value, 0xCFC + (where&3));
- break;
- case 2:
- outw(value, 0xCFC + (where&2));
- break;
- case 4:
- outl(value, 0xCFC);
- break;
- }
- return PCIBIOS_SUCCESSFUL;
-}
-
-struct pci_ops via82c505_ops = {
- .read = via82c505_read_config,
- .write = via82c505_write_config,
-};
-
-void __init via82c505_preinit(void)
-{
- printk(KERN_DEBUG "PCI: VIA 82c505\n");
- if (!request_region(0xA8,2,"via config")) {
- printk(KERN_WARNING"VIA 82c505: Unable to request region 0xA8\n");
- return;
- }
- if (!request_region(0xCF8,8,"pci config")) {
- printk(KERN_WARNING"VIA 82c505: Unable to request region 0xCF8\n");
- release_region(0xA8, 2);
- return;
- }
-
- /* Enable compatible Mode */
- outb(0x96,0xA8);
- outb(0x18,0xA9);
- outb(0x93,0xA8);
- outb(0xd0,0xA9);
-
-}
-
-int __init via82c505_setup(int nr, struct pci_sys_data *sys)
-{
- return (nr == 0);
-}
CONFIG_VIDEO_ML86V7667=y
CONFIG_SPI=y
CONFIG_SPI_SH_HSPI=y
+CONFIG_SOUND=y
+CONFIG_SND=y
+CONFIG_SND_SOC=y
+CONFIG_SND_SOC_RCAR=y
CONFIG_USB=y
CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
CONFIG_USB_EHCI_HCD=y
--- /dev/null
+CONFIG_SYSVIPC=y
+CONFIG_NO_HZ=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=16
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_EMBEDDED=y
+CONFIG_PERF_EVENTS=y
+CONFIG_SLAB=y
+# CONFIG_BLOCK is not set
+CONFIG_ARCH_SHMOBILE=y
+CONFIG_ARCH_R8A7791=y
+CONFIG_MACH_KOELSCH=y
+# CONFIG_SWP_EMULATE is not set
+CONFIG_CPU_BPREDICT_DISABLE=y
+CONFIG_PL310_ERRATA_588369=y
+CONFIG_ARM_ERRATA_754322=y
+CONFIG_SMP=y
+CONFIG_SCHED_MC=y
+CONFIG_NR_CPUS=8
+CONFIG_AEABI=y
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_ARM_APPENDED_DTB=y
+CONFIG_KEXEC=y
+CONFIG_AUTO_ZRELADDR=y
+CONFIG_VFP=y
+CONFIG_NEON=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_PM_RUNTIME=y
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_LEGACY_PTYS is not set
+CONFIG_SERIAL_SH_SCI=y
+CONFIG_SERIAL_SH_SCI_NR_UARTS=20
+CONFIG_SERIAL_SH_SCI_CONSOLE=y
+# CONFIG_HWMON is not set
+CONFIG_THERMAL=y
+CONFIG_RCAR_THERMAL=y
+# CONFIG_HID is not set
+# CONFIG_USB_SUPPORT is not set
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+# CONFIG_IOMMU_SUPPORT is not set
+# CONFIG_DNOTIFY is not set
+# CONFIG_INOTIFY_USER is not set
+CONFIG_TMPFS=y
+CONFIG_CONFIGFS_FS=y
+# CONFIG_MISC_FILESYSTEMS is not set
+# CONFIG_ENABLE_WARN_DEPRECATED is not set
+# CONFIG_ENABLE_MUST_CHECK is not set
+# CONFIG_ARM_UNWIND is not set
CONFIG_RCAR_THERMAL=y
CONFIG_REGULATOR=y
CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_DRM=y
+CONFIG_DRM_RCAR_DU=y
# CONFIG_USB_SUPPORT is not set
CONFIG_MMC=y
CONFIG_MMC_SDHI=y
CONFIG_VIDEO_RCAR_VIN=y
# CONFIG_MEDIA_SUBDRV_AUTOSELECT is not set
CONFIG_VIDEO_ADV7180=y
+CONFIG_DRM=y
+CONFIG_DRM_RCAR_DU=y
CONFIG_USB=y
CONFIG_USB_RCAR_PHY=y
CONFIG_MMC=y
+++ /dev/null
-CONFIG_EXPERIMENTAL=y
-# CONFIG_LOCALVERSION_AUTO is not set
-CONFIG_SYSVIPC=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_SYSFS_DEPRECATED_V2=y
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
-CONFIG_ARCH_SHARK=y
-CONFIG_LEDS=y
-CONFIG_LEDS_TIMER=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_FPE_NWFPE=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_LRO is not set
-# CONFIG_INET_DIAG is not set
-# CONFIG_IPV6 is not set
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-# CONFIG_STANDALONE is not set
-# CONFIG_FIRMWARE_IN_KERNEL is not set
-CONFIG_PARPORT=m
-CONFIG_PARPORT_PC=m
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_IDE=y
-CONFIG_BLK_DEV_IDECD=m
-CONFIG_SCSI=m
-CONFIG_BLK_DEV_SD=m
-CONFIG_CHR_DEV_ST=m
-CONFIG_BLK_DEV_SR=m
-CONFIG_CHR_DEV_SG=m
-CONFIG_NETDEVICES=y
-CONFIG_NET_ETHERNET=y
-CONFIG_NET_PCI=y
-CONFIG_CS89x0=y
-# CONFIG_SERIO_SERPORT is not set
-CONFIG_SERIAL_8250=y
-CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_PRINTER=m
-# CONFIG_HWMON is not set
-CONFIG_FB=y
-CONFIG_FB_CYBER2000=y
-# CONFIG_VGA_CONSOLE is not set
-CONFIG_FRAMEBUFFER_CONSOLE=y
-CONFIG_LOGO=y
-# CONFIG_LOGO_LINUX_MONO is not set
-# CONFIG_LOGO_LINUX_VGA16 is not set
-CONFIG_SOUND=m
-CONFIG_SOUND_PRIME=m
-CONFIG_SOUND_OSS=m
-CONFIG_SOUND_SB=m
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_DRV_CMOS=y
-CONFIG_EXT2_FS=y
-CONFIG_EXT3_FS=y
-CONFIG_ISO9660_FS=m
-CONFIG_JOLIET=y
-CONFIG_MSDOS_FS=m
-CONFIG_VFAT_FS=m
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_NFSD=m
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_NLS_CODEPAGE_437=m
-CONFIG_NLS_CODEPAGE_850=m
-CONFIG_NLS_ISO8859_1=m
-# CONFIG_ENABLE_MUST_CHECK is not set
-CONFIG_DEBUG_KERNEL=y
-# CONFIG_SCHED_DEBUG is not set
-# CONFIG_RCU_CPU_STALL_DETECTOR is not set
-CONFIG_DEBUG_USER=y
-CONFIG_HIGHMEM=y
# CONFIG_SWAP is not set
CONFIG_SYSVIPC=y
CONFIG_NO_HZ=y
CONFIG_NR_CPUS=2
CONFIG_PREEMPT=y
CONFIG_AEABI=y
+CONFIG_HIGHMEM=y
+CONFIG_ARM_APPENDED_DTB=y
+CONFIG_ARM_ATAG_DTB_COMPAT=y
CONFIG_CMDLINE="root=/dev/ram0 console=ttyAMA2,115200n8"
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND=y
CONFIG_WATCHDOG=y
CONFIG_MFD_STMPE=y
CONFIG_MFD_TC3589X=y
-CONFIG_REGULATOR_GPIO=y
CONFIG_REGULATOR_AB8500=y
+CONFIG_REGULATOR_GPIO=y
CONFIG_SOUND=y
CONFIG_SND=y
CONFIG_SND_SOC=y
CONFIG_USB=y
CONFIG_USB_MUSB_HDRC=y
CONFIG_USB_MUSB_UX500=y
-CONFIG_USB_PHY=y
CONFIG_AB8500_USB=y
CONFIG_USB_GADGET=y
-CONFIG_USB_GADGET_MUSB_HDRC=y
CONFIG_USB_ETH=m
CONFIG_MMC=y
CONFIG_MMC_UNSAFE_RESUME=y
CONFIG_ROOT_NFS=y
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_ISO8859_1=y
-CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_INFO=y
CONFIG_DEBUG_FS=y
+CONFIG_MAGIC_SYSRQ=y
CONFIG_DEBUG_KERNEL=y
# CONFIG_SCHED_DEBUG is not set
# CONFIG_DEBUG_PREEMPT is not set
-CONFIG_DEBUG_INFO=y
# CONFIG_FTRACE is not set
CONFIG_DEBUG_USER=y
CONFIG_CRYPTO_DEV_UX500=y
extern void dc21285_preinit(void);
extern void dc21285_postinit(void);
-extern struct pci_ops via82c505_ops;
-extern int via82c505_setup(int nr, struct pci_sys_data *);
-extern void via82c505_init(void *sysdata);
-
#endif /* __ASM_MACH_PCI_H */
+++ /dev/null
-/* You shouldn't include this file. Use linux/sched_clock.h instead.
- * Temporary file until all asm/sched_clock.h users are gone
- */
-#include <linux/sched_clock.h>
* This file contains the ARM-specific time handling details:
* reading the RTC at bootup, etc...
*/
+#include <linux/clk-provider.h>
+#include <linux/clocksource.h>
+#include <linux/errno.h>
#include <linux/export.h>
-#include <linux/kernel.h>
-#include <linux/interrupt.h>
-#include <linux/time.h>
#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/kernel.h>
+#include <linux/profile.h>
#include <linux/sched.h>
+#include <linux/sched_clock.h>
#include <linux/smp.h>
+#include <linux/time.h>
#include <linux/timex.h>
-#include <linux/errno.h>
-#include <linux/profile.h>
#include <linux/timer.h>
-#include <linux/clocksource.h>
-#include <linux/irq.h>
-#include <linux/sched_clock.h>
-#include <asm/thread_info.h>
-#include <asm/stacktrace.h>
#include <asm/mach/arch.h>
#include <asm/mach/time.h>
+#include <asm/stacktrace.h>
+#include <asm/thread_info.h>
#if defined(CONFIG_RTC_DRV_CMOS) || defined(CONFIG_RTC_DRV_CMOS_MODULE) || \
defined(CONFIG_NVRAM) || defined(CONFIG_NVRAM_MODULE)
void __init time_init(void)
{
- if (machine_desc->init_time)
+ if (machine_desc->init_time) {
machine_desc->init_time();
- else
+ } else {
+#ifdef CONFIG_COMMON_CLK
+ of_clk_init(NULL);
+#endif
clocksource_of_init();
+ }
}
endif
lib-$(CONFIG_ARCH_RPC) += ecard.o io-acorn.o floppydma.o
-lib-$(CONFIG_ARCH_SHARK) += io-shark.o
$(obj)/csumpartialcopy.o: $(obj)/csumpartialcopygeneric.S
$(obj)/csumpartialcopyuser.o: $(obj)/csumpartialcopygeneric.S
+++ /dev/null
-/*
- * linux/arch/arm/lib/io-shark.c
- *
- * by Alexander Schulz
- *
- * derived from:
- * linux/arch/arm/lib/io-ebsa.S
- * Copyright (C) 1995, 1996 Russell King
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
static const char * const bcm11351_dt_compat[] = { "brcm,bcm11351", NULL, };
DT_MACHINE_START(BCM11351_DT, "Broadcom Application Processor")
- .init_time = clocksource_of_init,
.init_machine = board_init,
.restart = bcm_kona_restart,
.dt_compat = bcm11351_dt_compat,
#include <linux/of_address.h>
#include <linux/of_platform.h>
#include <linux/clk/bcm2835.h>
-#include <linux/clocksource.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
.init_irq = bcm2835_init_irq,
.handle_irq = bcm2835_handle_irq,
.init_machine = bcm2835_init,
- .init_time = clocksource_of_init,
.restart = bcm2835_restart,
.dt_compat = bcm2835_compat
MACHINE_END
#include <linux/clockchips.h>
#include <linux/clocksource.h>
#include <linux/clk-provider.h>
+#include <linux/sched_clock.h>
#include <asm/exception.h>
#include <asm/mach/irq.h>
#include <asm/mach/map.h>
#include <asm/mach/time.h>
-#include <asm/sched_clock.h>
#include <asm/system_misc.h>
#include <mach/hardware.h>
#include <linux/mtd/partitions.h>
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
+#include <linux/platform_data/gpio-davinci.h>
+#include <linux/platform_data/mtd-davinci.h>
+#include <linux/platform_data/mtd-davinci-aemif.h>
+#include <linux/platform_data/spi-davinci.h>
+#include <linux/platform_data/usb-davinci.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
+#include <mach/common.h>
#include <mach/cp_intc.h>
#include <mach/mux.h>
-#include <linux/platform_data/mtd-davinci.h>
#include <mach/da8xx.h>
-#include <linux/platform_data/usb-davinci.h>
-#include <linux/platform_data/mtd-davinci-aemif.h>
-#include <linux/platform_data/spi-davinci.h>
#define DA830_EVM_PHY_ID ""
/*
struct davinci_soc_info *soc_info = &davinci_soc_info;
int ret;
+ ret = da830_register_gpio();
+ if (ret)
+ pr_warn("da830_evm_init: GPIO init failed: %d\n", ret);
+
ret = da830_register_edma(da830_edma_rsv);
if (ret)
pr_warning("da830_evm_init: edma registration failed: %d\n",
#include <linux/mtd/partitions.h>
#include <linux/mtd/physmap.h>
#include <linux/platform_device.h>
+#include <linux/platform_data/gpio-davinci.h>
#include <linux/platform_data/mtd-davinci.h>
#include <linux/platform_data/mtd-davinci-aemif.h>
#include <linux/platform_data/spi-davinci.h>
#include <linux/spi/flash.h>
#include <linux/wl12xx.h>
+#include <mach/common.h>
#include <mach/cp_intc.h>
#include <mach/da8xx.h>
#include <mach/mux.h>
{
int ret;
+ ret = da850_register_gpio();
+ if (ret)
+ pr_warn("%s: GPIO init failed: %d\n", __func__, ret);
+
ret = pmic_tps65070_init();
if (ret)
pr_warn("%s: TPS65070 PMIC init failed: %d\n", __func__, ret);
#include <media/tvp514x.h>
#include <linux/spi/spi.h>
#include <linux/spi/eeprom.h>
+#include <linux/platform_data/gpio-davinci.h>
+#include <linux/platform_data/i2c-davinci.h>
+#include <linux/platform_data/mtd-davinci.h>
+#include <linux/platform_data/mmc-davinci.h>
+#include <linux/platform_data/usb-davinci.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
-#include <linux/platform_data/i2c-davinci.h>
#include <mach/serial.h>
-#include <linux/platform_data/mtd-davinci.h>
-#include <linux/platform_data/mmc-davinci.h>
-#include <linux/platform_data/usb-davinci.h>
+#include <mach/common.h>
#include "davinci.h"
static __init void dm355_evm_init(void)
{
struct clk *aemif;
+ int ret;
+
+ ret = dm355_gpio_register();
+ if (ret)
+ pr_warn("%s: GPIO init failed: %d\n", __func__, ret);
gpio_request(1, "dm9000");
gpio_direction_input(1);
#include <linux/clk.h>
#include <linux/spi/spi.h>
#include <linux/spi/eeprom.h>
+#include <linux/platform_data/i2c-davinci.h>
+#include <linux/platform_data/mmc-davinci.h>
+#include <linux/platform_data/mtd-davinci.h>
+#include <linux/platform_data/usb-davinci.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
-#include <linux/platform_data/i2c-davinci.h>
+#include <mach/common.h>
#include <mach/serial.h>
-#include <linux/platform_data/mtd-davinci.h>
-#include <linux/platform_data/mmc-davinci.h>
-#include <linux/platform_data/usb-davinci.h>
#include "davinci.h"
static __init void dm355_leopard_init(void)
{
struct clk *aemif;
+ int ret;
+
+ ret = dm355_gpio_register();
+ if (ret)
+ pr_warn("%s: GPIO init failed: %d\n", __func__, ret);
gpio_request(9, "dm9000");
gpio_direction_input(9);
static __init void dm365_evm_init(void)
{
+ int ret;
+
+ ret = dm365_gpio_register();
+ if (ret)
+ pr_warn("%s: GPIO init failed: %d\n", __func__, ret);
+
evm_init_i2c();
davinci_serial_init(dm365_serial_device);
static __init void davinci_evm_init(void)
{
+ int ret;
struct clk *aemif_clk;
struct davinci_soc_info *soc_info = &davinci_soc_info;
+ ret = dm644x_gpio_register();
+ if (ret)
+ pr_warn("%s: GPIO init failed: %d\n", __func__, ret);
+
aemif_clk = clk_get(NULL, "aemif");
clk_prepare_enable(aemif_clk);
#include <linux/mtd/partitions.h>
#include <linux/clk.h>
#include <linux/export.h>
+#include <linux/platform_data/gpio-davinci.h>
+#include <linux/platform_data/i2c-davinci.h>
+#include <linux/platform_data/mtd-davinci.h>
+#include <linux/platform_data/mtd-davinci-aemif.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <mach/common.h>
+#include <mach/irqs.h>
#include <mach/serial.h>
-#include <linux/platform_data/i2c-davinci.h>
-#include <linux/platform_data/mtd-davinci.h>
#include <mach/clock.h>
#include <mach/cdce949.h>
-#include <linux/platform_data/mtd-davinci-aemif.h>
#include "davinci.h"
#include "clock.h"
static __init void evm_init(void)
{
+ int ret;
struct davinci_soc_info *soc_info = &davinci_soc_info;
+ ret = dm646x_gpio_register();
+ if (ret)
+ pr_warn("%s: GPIO init failed: %d\n", __func__, ret);
+
evm_init_i2c();
davinci_serial_init(dm646x_serial_device);
dm646x_init_mcasp0(&dm646x_evm_snd_data[0]);
#include <linux/platform_device.h>
#include <linux/gpio.h>
#include <linux/mtd/partitions.h>
+#include <linux/platform_data/gpio-davinci.h>
+#include <linux/platform_data/i2c-davinci.h>
+#include <linux/platform_data/mmc-davinci.h>
+#include <linux/platform_data/mtd-davinci.h>
+#include <linux/platform_data/usb-davinci.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <mach/common.h>
-#include <linux/platform_data/i2c-davinci.h>
#include <mach/serial.h>
#include <mach/mux.h>
-#include <linux/platform_data/mtd-davinci.h>
-#include <linux/platform_data/mmc-davinci.h>
-#include <linux/platform_data/usb-davinci.h>
#include "davinci.h"
static __init void davinci_ntosd2_init(void)
{
+ int ret;
struct clk *aemif_clk;
struct davinci_soc_info *soc_info = &davinci_soc_info;
+ ret = dm644x_gpio_register();
+ if (ret)
+ pr_warn("%s: GPIO init failed: %d\n", __func__, ret);
+
aemif_clk = clk_get(NULL, "aemif");
clk_prepare_enable(aemif_clk);
#include <linux/init.h>
#include <linux/console.h>
#include <linux/gpio.h>
+#include <linux/platform_data/gpio-davinci.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
+#include <mach/common.h>
#include <mach/cp_intc.h>
#include <mach/da8xx.h>
#include <mach/mux.h>
{
int ret;
+ ret = da850_register_gpio();
+ if (ret)
+ pr_warn("%s: GPIO init failed: %d\n", __func__, ret);
+
davinci_serial_init(da8xx_serial_device);
omapl138_hawk_config_emac();
#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/clk.h>
+#include <linux/platform_data/gpio-davinci.h>
#include <asm/mach/map.h>
#include <mach/common.h>
#include <mach/time.h>
#include <mach/da8xx.h>
-#include <mach/gpio-davinci.h>
#include "clock.h"
#include "mux.h"
},
};
+static struct davinci_gpio_platform_data da830_gpio_platform_data = {
+ .ngpio = 128,
+ .intc_irq_num = DA830_N_CP_INTC_IRQ,
+};
+
+int __init da830_register_gpio(void)
+{
+ return da8xx_register_gpio(&da830_gpio_platform_data);
+}
+
static struct davinci_timer_instance da830_timer_instance[2] = {
{
.base = DA8XX_TIMER64P0_BASE,
.intc_irq_prios = da830_default_priorities,
.intc_irq_num = DA830_N_CP_INTC_IRQ,
.timer_info = &da830_timer_info,
- .gpio_type = GPIO_TYPE_DAVINCI,
- .gpio_base = DA8XX_GPIO_BASE,
- .gpio_num = 128,
- .gpio_irq = IRQ_DA8XX_GPIO0,
.emac_pdata = &da8xx_emac_pdata,
};
#include <linux/platform_device.h>
#include <linux/cpufreq.h>
#include <linux/regulator/consumer.h>
+#include <linux/platform_data/gpio-davinci.h>
#include <asm/mach/map.h>
#include <mach/da8xx.h>
#include <mach/cpufreq.h>
#include <mach/pm.h>
-#include <mach/gpio-davinci.h>
#include "clock.h"
#include "mux.h"
return platform_device_register(&da850_vpif_capture_dev);
}
+static struct davinci_gpio_platform_data da850_gpio_platform_data = {
+ .ngpio = 144,
+ .intc_irq_num = DA850_N_CP_INTC_IRQ,
+};
+
+int __init da850_register_gpio(void)
+{
+ return da8xx_register_gpio(&da850_gpio_platform_data);
+}
+
static struct davinci_soc_info davinci_soc_info_da850 = {
.io_desc = da850_io_desc,
.io_desc_num = ARRAY_SIZE(da850_io_desc),
.intc_irq_prios = da850_default_priorities,
.intc_irq_num = DA850_N_CP_INTC_IRQ,
.timer_info = &da850_timer_info,
- .gpio_type = GPIO_TYPE_DAVINCI,
- .gpio_base = DA8XX_GPIO_BASE,
- .gpio_num = 144,
- .gpio_irq = IRQ_DA8XX_GPIO0,
.emac_pdata = &da8xx_emac_pdata,
.sram_dma = DA8XX_SHARED_RAM_BASE,
.sram_len = SZ_128K,
#define DAVINCI_SYSMOD_VIRT(x) (davinci_sysmod_base + (x))
void davinci_map_sysmod(void);
+#define DAVINCI_GPIO_BASE 0x01C67000
+int davinci_gpio_register(struct resource *res, int size, void *pdata);
+
/* DM355 base addresses */
#define DM355_ASYNC_EMIF_CONTROL_BASE 0x01e10000
#define DM355_ASYNC_EMIF_DATA_CE0_BASE 0x02000000
const struct spi_board_info *info, unsigned len);
void dm355_init_asp1(u32 evt_enable, struct snd_platform_data *pdata);
int dm355_init_video(struct vpfe_config *, struct vpbe_config *);
+int dm355_gpio_register(void);
/* DM365 function declarations */
void dm365_init(void);
void dm365_init_spi0(unsigned chipselect_mask,
const struct spi_board_info *info, unsigned len);
int dm365_init_video(struct vpfe_config *, struct vpbe_config *);
+int dm365_gpio_register(void);
/* DM644x function declarations */
void dm644x_init(void);
void dm644x_init_asp(struct snd_platform_data *pdata);
int dm644x_init_video(struct vpfe_config *, struct vpbe_config *);
+int dm644x_gpio_register(void);
/* DM646x function declarations */
void dm646x_init(void);
void dm646x_video_init(void);
void dm646x_setup_vpif(struct vpif_display_config *,
struct vpif_capture_config *);
+int dm646x_gpio_register(void);
extern struct platform_device dm365_serial_device[];
extern struct platform_device dm355_serial_device[];
return platform_device_register(&da8xx_lcdc_device);
}
+static struct resource da8xx_gpio_resources[] = {
+ { /* registers */
+ .start = DA8XX_GPIO_BASE,
+ .end = DA8XX_GPIO_BASE + SZ_4K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ { /* interrupt */
+ .start = IRQ_DA8XX_GPIO0,
+ .end = IRQ_DA8XX_GPIO8,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device da8xx_gpio_device = {
+ .name = "davinci_gpio",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(da8xx_gpio_resources),
+ .resource = da8xx_gpio_resources,
+};
+
+int __init da8xx_register_gpio(void *pdata)
+{
+ da8xx_gpio_device.dev.platform_data = pdata;
+ return platform_device_register(&da8xx_gpio_device);
+}
+
static struct resource da8xx_mmcsd0_resources[] = {
{ /* registers */
.start = DA8XX_MMCSD0_BASE,
platform_device_register(&davinci_wdt_device);
}
+static struct platform_device davinci_gpio_device = {
+ .name = "davinci_gpio",
+ .id = -1,
+};
+
+int davinci_gpio_register(struct resource *res, int size, void *pdata)
+{
+ davinci_gpio_device.resource = res;
+ davinci_gpio_device.num_resources = size;
+ davinci_gpio_device.dev.platform_data = pdata;
+ return platform_device_register(&davinci_gpio_device);
+}
+
/*-------------------------------------------------------------------------*/
/*-------------------------------------------------------------------------*/
#include <linux/serial_8250.h>
#include <linux/platform_device.h>
#include <linux/dma-mapping.h>
-
#include <linux/spi/spi.h>
+#include <linux/platform_data/edma.h>
+#include <linux/platform_data/gpio-davinci.h>
+#include <linux/platform_data/spi-davinci.h>
#include <asm/mach/map.h>
#include <mach/time.h>
#include <mach/serial.h>
#include <mach/common.h>
-#include <linux/platform_data/spi-davinci.h>
-#include <mach/gpio-davinci.h>
-#include <linux/platform_data/edma.h>
#include "davinci.h"
#include "clock.h"
},
};
+static struct resource dm355_gpio_resources[] = {
+ { /* registers */
+ .start = DAVINCI_GPIO_BASE,
+ .end = DAVINCI_GPIO_BASE + SZ_4K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ { /* interrupt */
+ .start = IRQ_DM355_GPIOBNK0,
+ .end = IRQ_DM355_GPIOBNK6,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct davinci_gpio_platform_data dm355_gpio_platform_data = {
+ .ngpio = 104,
+ .intc_irq_num = DAVINCI_N_AINTC_IRQ,
+};
+
+int __init dm355_gpio_register(void)
+{
+ return davinci_gpio_register(dm355_gpio_resources,
+ sizeof(dm355_gpio_resources),
+ &dm355_gpio_platform_data);
+}
/*----------------------------------------------------------------------*/
static struct map_desc dm355_io_desc[] = {
.intc_irq_prios = dm355_default_priorities,
.intc_irq_num = DAVINCI_N_AINTC_IRQ,
.timer_info = &dm355_timer_info,
- .gpio_type = GPIO_TYPE_DAVINCI,
- .gpio_base = DAVINCI_GPIO_BASE,
- .gpio_num = 104,
- .gpio_irq = IRQ_DM355_GPIOBNK0,
.sram_dma = 0x00010000,
.sram_len = SZ_32K,
};
#include <linux/dma-mapping.h>
#include <linux/spi/spi.h>
#include <linux/platform_data/edma.h>
+#include <linux/platform_data/gpio-davinci.h>
+#include <linux/platform_data/keyscan-davinci.h>
+#include <linux/platform_data/spi-davinci.h>
#include <asm/mach/map.h>
#include <mach/time.h>
#include <mach/serial.h>
#include <mach/common.h>
-#include <linux/platform_data/keyscan-davinci.h>
-#include <linux/platform_data/spi-davinci.h>
-#include <mach/gpio-davinci.h>
#include "davinci.h"
#include "clock.h"
platform_device_register(&dm365_spi0_device);
}
+static struct resource dm365_gpio_resources[] = {
+ { /* registers */
+ .start = DAVINCI_GPIO_BASE,
+ .end = DAVINCI_GPIO_BASE + SZ_4K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ { /* interrupt */
+ .start = IRQ_DM365_GPIO0,
+ .end = IRQ_DM365_GPIO7,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct davinci_gpio_platform_data dm365_gpio_platform_data = {
+ .ngpio = 104,
+ .intc_irq_num = DAVINCI_N_AINTC_IRQ,
+ .gpio_unbanked = 8,
+};
+
+int __init dm365_gpio_register(void)
+{
+ return davinci_gpio_register(dm365_gpio_resources,
+ sizeof(dm365_gpio_resources),
+ &dm365_gpio_platform_data);
+}
+
static struct emac_platform_data dm365_emac_pdata = {
.ctrl_reg_offset = DM365_EMAC_CNTRL_OFFSET,
.ctrl_mod_reg_offset = DM365_EMAC_CNTRL_MOD_OFFSET,
.intc_irq_prios = dm365_default_priorities,
.intc_irq_num = DAVINCI_N_AINTC_IRQ,
.timer_info = &dm365_timer_info,
- .gpio_type = GPIO_TYPE_DAVINCI,
- .gpio_base = DAVINCI_GPIO_BASE,
- .gpio_num = 104,
- .gpio_irq = IRQ_DM365_GPIO0,
- .gpio_unbanked = 8, /* really 16 ... skip muxed GPIOs */
.emac_pdata = &dm365_emac_pdata,
.sram_dma = 0x00010000,
.sram_len = SZ_32K,
#include <linux/serial_8250.h>
#include <linux/platform_device.h>
#include <linux/platform_data/edma.h>
+#include <linux/platform_data/gpio-davinci.h>
#include <asm/mach/map.h>
#include <mach/time.h>
#include <mach/serial.h>
#include <mach/common.h>
-#include <mach/gpio-davinci.h>
#include "davinci.h"
#include "clock.h"
},
};
+static struct resource dm644_gpio_resources[] = {
+ { /* registers */
+ .start = DAVINCI_GPIO_BASE,
+ .end = DAVINCI_GPIO_BASE + SZ_4K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ { /* interrupt */
+ .start = IRQ_GPIOBNK0,
+ .end = IRQ_GPIOBNK4,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct davinci_gpio_platform_data dm644_gpio_platform_data = {
+ .ngpio = 71,
+ .intc_irq_num = DAVINCI_N_AINTC_IRQ,
+};
+
+int __init dm644x_gpio_register(void)
+{
+ return davinci_gpio_register(dm644_gpio_resources,
+ sizeof(dm644_gpio_resources),
+ &dm644_gpio_platform_data);
+}
/*----------------------------------------------------------------------*/
static struct map_desc dm644x_io_desc[] = {
.intc_irq_prios = dm644x_default_priorities,
.intc_irq_num = DAVINCI_N_AINTC_IRQ,
.timer_info = &dm644x_timer_info,
- .gpio_type = GPIO_TYPE_DAVINCI,
- .gpio_base = DAVINCI_GPIO_BASE,
- .gpio_num = 71,
- .gpio_irq = IRQ_GPIOBNK0,
.emac_pdata = &dm644x_emac_pdata,
.sram_dma = 0x00008000,
.sram_len = SZ_16K,
#include <linux/serial_8250.h>
#include <linux/platform_device.h>
#include <linux/platform_data/edma.h>
+#include <linux/platform_data/gpio-davinci.h>
#include <asm/mach/map.h>
#include <mach/time.h>
#include <mach/serial.h>
#include <mach/common.h>
-#include <mach/gpio-davinci.h>
#include "davinci.h"
#include "clock.h"
.num_resources = ARRAY_SIZE(vpif_capture_resource),
};
+static struct resource dm646x_gpio_resources[] = {
+ { /* registers */
+ .start = DAVINCI_GPIO_BASE,
+ .end = DAVINCI_GPIO_BASE + SZ_4K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ { /* interrupt */
+ .start = IRQ_DM646X_GPIOBNK0,
+ .end = IRQ_DM646X_GPIOBNK2,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct davinci_gpio_platform_data dm646x_gpio_platform_data = {
+ .ngpio = 43,
+ .intc_irq_num = DAVINCI_N_AINTC_IRQ,
+};
+
+int __init dm646x_gpio_register(void)
+{
+ return davinci_gpio_register(dm646x_gpio_resources,
+ sizeof(dm646x_gpio_resources),
+ &dm646x_gpio_platform_data);
+}
/*----------------------------------------------------------------------*/
static struct map_desc dm646x_io_desc[] = {
.intc_irq_prios = dm646x_default_priorities,
.intc_irq_num = DAVINCI_N_AINTC_IRQ,
.timer_info = &dm646x_timer_info,
- .gpio_type = GPIO_TYPE_DAVINCI,
- .gpio_base = DAVINCI_GPIO_BASE,
- .gpio_num = 43, /* Only 33 usable */
- .gpio_irq = IRQ_DM646X_GPIOBNK0,
.emac_pdata = &dm646x_emac_pdata,
.sram_dma = 0x10010000,
.sram_len = SZ_32K,
int da850_register_mmcsd1(struct davinci_mmc_config *config);
void da8xx_register_mcasp(int id, struct snd_platform_data *pdata);
int da8xx_register_rtc(void);
+int da8xx_register_gpio(void *pdata);
int da850_register_cpufreq(char *async_clk);
int da8xx_register_cpuidle(void);
void __iomem *da8xx_get_mem_ctlr(void);
void da8xx_restart(enum reboot_mode mode, const char *cmd);
void da8xx_rproc_reserve_cma(void);
int da8xx_register_rproc(void);
+int da850_register_gpio(void);
+int da830_register_gpio(void);
extern struct platform_device da8xx_serial_device[];
extern struct emac_platform_data da8xx_emac_pdata;
+++ /dev/null
-/*
- * TI DaVinci GPIO Support
- *
- * Copyright (c) 2006 David Brownell
- * Copyright (c) 2007, MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#ifndef __DAVINCI_DAVINCI_GPIO_H
-#define __DAVINCI_DAVINCI_GPIO_H
-
-#include <linux/io.h>
-#include <linux/spinlock.h>
-
-#include <asm-generic/gpio.h>
-
-#include <mach/irqs.h>
-#include <mach/common.h>
-
-#define DAVINCI_GPIO_BASE 0x01C67000
-
-enum davinci_gpio_type {
- GPIO_TYPE_DAVINCI = 0,
- GPIO_TYPE_TNETV107X,
-};
-
-/*
- * basic gpio routines
- *
- * board-specific init should be done by arch/.../.../board-XXX.c (maybe
- * initializing banks together) rather than boot loaders; kexec() won't
- * go through boot loaders.
- *
- * the gpio clock will be turned on when gpios are used, and you may also
- * need to pay attention to PINMUX registers to be sure those pins are
- * used as gpios, not with other peripherals.
- *
- * On-chip GPIOs are numbered 0..(DAVINCI_N_GPIO-1). For documentation,
- * and maybe for later updates, code may write GPIO(N). These may be
- * all 1.8V signals, all 3.3V ones, or a mix of the two. A given chip
- * may not support all the GPIOs in that range.
- *
- * GPIOs can also be on external chips, numbered after the ones built-in
- * to the DaVinci chip. For now, they won't be usable as IRQ sources.
- */
-#define GPIO(X) (X) /* 0 <= X <= (DAVINCI_N_GPIO - 1) */
-
-/* Convert GPIO signal to GPIO pin number */
-#define GPIO_TO_PIN(bank, gpio) (16 * (bank) + (gpio))
-
-struct davinci_gpio_controller {
- struct gpio_chip chip;
- int irq_base;
- spinlock_t lock;
- void __iomem *regs;
- void __iomem *set_data;
- void __iomem *clr_data;
- void __iomem *in_data;
-};
-
-/* The __gpio_to_controller() and __gpio_mask() functions inline to constants
- * with constant parameters; or in outlined code they execute at runtime.
- *
- * You'd access the controller directly when reading or writing more than
- * one gpio value at a time, and to support wired logic where the value
- * being driven by the cpu need not match the value read back.
- *
- * These are NOT part of the cross-platform GPIO interface
- */
-static inline struct davinci_gpio_controller *
-__gpio_to_controller(unsigned gpio)
-{
- struct davinci_gpio_controller *ctlrs = davinci_soc_info.gpio_ctlrs;
- int index = gpio / 32;
-
- if (!ctlrs || index >= davinci_soc_info.gpio_ctlrs_num)
- return NULL;
-
- return ctlrs + index;
-}
-
-static inline u32 __gpio_mask(unsigned gpio)
-{
- return 1 << (gpio % 32);
-}
-
-#endif /* __DAVINCI_DAVINCI_GPIO_H */
+++ /dev/null
-/*
- * TI DaVinci GPIO Support
- *
- * Copyright (c) 2006 David Brownell
- * Copyright (c) 2007, MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#ifndef __DAVINCI_GPIO_H
-#define __DAVINCI_GPIO_H
-
-#include <asm-generic/gpio.h>
-
-#define __ARM_GPIOLIB_COMPLEX
-
-/* The inline versions use the static inlines in the driver header */
-#include "gpio-davinci.h"
-
-/*
- * The get/set/clear functions will inline when called with constant
- * parameters referencing built-in GPIOs, for low-overhead bitbanging.
- *
- * gpio_set_value() will inline only on traditional Davinci style controllers
- * with distinct set/clear registers.
- *
- * Otherwise, calls with variable parameters or referencing external
- * GPIOs (e.g. on GPIO expander chips) use outlined functions.
- */
-static inline void gpio_set_value(unsigned gpio, int value)
-{
- if (__builtin_constant_p(value) && gpio < davinci_soc_info.gpio_num) {
- struct davinci_gpio_controller *ctlr;
- u32 mask;
-
- ctlr = __gpio_to_controller(gpio);
-
- if (ctlr->set_data != ctlr->clr_data) {
- mask = __gpio_mask(gpio);
- if (value)
- __raw_writel(mask, ctlr->set_data);
- else
- __raw_writel(mask, ctlr->clr_data);
- return;
- }
- }
-
- __gpio_set_value(gpio, value);
-}
-
-/* Returns zero or nonzero; works for gpios configured as inputs OR
- * as outputs, at least for built-in GPIOs.
- *
- * NOTE: for built-in GPIOs, changes in reported values are synchronized
- * to the GPIO clock. This is easily seen after calling gpio_set_value()
- * and then immediately gpio_get_value(), where the gpio_get_value() will
- * return the old value until the GPIO clock ticks and the new value gets
- * latched.
- */
-static inline int gpio_get_value(unsigned gpio)
-{
- struct davinci_gpio_controller *ctlr;
-
- if (!__builtin_constant_p(gpio) || gpio >= davinci_soc_info.gpio_num)
- return __gpio_get_value(gpio);
-
- ctlr = __gpio_to_controller(gpio);
- return __gpio_mask(gpio) & __raw_readl(ctlr->in_data);
-}
-
-static inline int gpio_cansleep(unsigned gpio)
-{
- if (__builtin_constant_p(gpio) && gpio < davinci_soc_info.gpio_num)
- return 0;
- else
- return __gpio_cansleep(gpio);
-}
-
-static inline int irq_to_gpio(unsigned irq)
-{
- /* don't support the reverse mapping */
- return -ENOSYS;
-}
-
-#endif /* __DAVINCI_GPIO_H */
#include <linux/init.h>
#include <linux/clk-provider.h>
-#include <linux/clocksource.h>
-#include <linux/irqchip.h>
#include <linux/of.h>
#include <linux/of_platform.h>
-#include <linux/platform_data/usb-ehci-orion.h>
#include <asm/hardware/cache-tauros2.h>
#include <asm/mach/arch.h>
#include <mach/dove.h>
#include <mach/pm.h>
#include <plat/common.h>
-#include <plat/irq.h>
#include "common.h"
-/*
- * There are still devices that doesn't even know about DT,
- * get clock gates here and add a clock lookup.
- */
-static void __init dove_legacy_clk_init(void)
-{
- struct device_node *np = of_find_compatible_node(NULL, NULL,
- "marvell,dove-gating-clock");
- struct of_phandle_args clkspec;
-
- clkspec.np = np;
- clkspec.args_count = 1;
-
- clkspec.args[0] = CLOCK_GATING_BIT_PCIE0;
- orion_clkdev_add("0", "pcie",
- of_clk_get_from_provider(&clkspec));
-
- clkspec.args[0] = CLOCK_GATING_BIT_PCIE1;
- orion_clkdev_add("1", "pcie",
- of_clk_get_from_provider(&clkspec));
-}
-
-static void __init dove_dt_time_init(void)
-{
- of_clk_init(NULL);
- clocksource_of_init();
-}
-
-static void __init dove_dt_init_early(void)
-{
- mvebu_mbus_init("marvell,dove-mbus",
- BRIDGE_WINS_BASE, BRIDGE_WINS_SZ,
- DOVE_MC_WINS_BASE, DOVE_MC_WINS_SZ);
-}
-
static void __init dove_dt_init(void)
{
pr_info("Dove 88AP510 SoC\n");
#ifdef CONFIG_CACHE_TAUROS2
tauros2_init(0);
#endif
- dove_setup_cpu_wins();
-
- /* Setup clocks for legacy devices */
- dove_legacy_clk_init();
-
- /* Internal devices not ported to DT yet */
- dove_pcie_init(1, 1);
-
+ BUG_ON(mvebu_mbus_dt_init());
of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
}
DT_MACHINE_START(DOVE_DT, "Marvell Dove (Flattened Device Tree)")
.map_io = dove_map_io,
- .init_early = dove_dt_init_early,
- .init_time = dove_dt_time_init,
.init_machine = dove_dt_init,
.restart = dove_restart,
.dt_compat = dove_dt_board_compat,
#include <linux/export.h>
#include <linux/irqdomain.h>
#include <linux/of_address.h>
-#include <linux/clocksource.h>
-#include <linux/clk-provider.h>
#include <linux/irqchip/arm-gic.h>
#include <linux/irqchip/chained_irq.h>
iotable_init(exynos5250_iodesc, ARRAY_SIZE(exynos5250_iodesc));
}
-void __init exynos_init_time(void)
-{
- of_clk_init(NULL);
- clocksource_of_init();
-}
-
struct bus_type exynos_subsys = {
.name = "exynos-core",
.dev_name = "exynos-core",
#include <linux/of.h>
void mct_init(void __iomem *base, int irq_g0, int irq_l0, int irq_l1);
-void exynos_init_time(void);
struct map_desc;
void exynos_init_io(void);
#include <linux/of_fdt.h>
#include <linux/serial_core.h>
#include <linux/memblock.h>
-#include <linux/clocksource.h>
#include <asm/mach/arch.h>
#include <plat/mfc.h>
.init_early = exynos_firmware_init,
.init_machine = exynos4_dt_machine_init,
.init_late = exynos_init_late,
- .init_time = exynos_init_time,
.dt_compat = exynos4_dt_compat,
.restart = exynos4_restart,
.reserve = exynos4_reserve,
#include <linux/of_fdt.h>
#include <linux/memblock.h>
#include <linux/io.h>
-#include <linux/clocksource.h>
#include <asm/mach/arch.h>
#include <mach/regs-pmu.h>
.map_io = exynos_init_io,
.init_machine = exynos5_dt_machine_init,
.init_late = exynos_init_late,
- .init_time = exynos_init_time,
.dt_compat = exynos5_dt_compat,
.restart = exynos5_restart,
.reserve = exynos5_reserve,
select ARM_GIC
select ARM_TIMER_SP804
select CACHE_L2X0
- select CLKDEV_LOOKUP
select COMMON_CLK
select CPU_V7
select GENERIC_CLOCKEVENTS
#include <linux/of_platform.h>
#include <linux/of_address.h>
#include <linux/amba/bus.h>
-#include <linux/clk-provider.h>
#include <asm/cacheflush.h>
#include <asm/cputype.h>
}
}
-static void __init highbank_timer_init(void)
-{
- struct device_node *np;
-
- /* Map system registers */
- np = of_find_compatible_node(NULL, NULL, "calxeda,hb-sregs");
- sregs_base = of_iomap(np, 0);
- WARN_ON(!sregs_base);
-
- of_clk_init(NULL);
-
- clocksource_of_init();
-}
-
static void highbank_power_off(void)
{
highbank_set_pwr_shutdown();
static void __init highbank_init(void)
{
+ struct device_node *np;
+
+ /* Map system registers */
+ np = of_find_compatible_node(NULL, NULL, "calxeda,hb-sregs");
+ sregs_base = of_iomap(np, 0);
+ WARN_ON(!sregs_base);
+
pm_power_off = highbank_power_off;
highbank_pm_init();
#endif
.smp = smp_ops(highbank_smp_ops),
.init_irq = highbank_init_irq,
- .init_time = highbank_timer_init,
.init_machine = highbank_init,
.dt_compat = highbank_match,
.restart = highbank_restart,
select ARM_CPU_SUSPEND if PM
select ARM_PATCH_PHYS_VIRT
select AUTO_ZRELADDR if !ZBOOT_ROM
- select CLKDEV_LOOKUP
select CLKSRC_MMIO
+ select COMMON_CLK
select GENERIC_ALLOCATOR
select GENERIC_CLOCKEVENTS
select GENERIC_IRQ_CHIP
config SOC_IMX1
bool
select ARCH_MX1
- select COMMON_CLK
select CPU_ARM920T
select IMX_HAVE_IOMUX_V1
select MXC_AVIC
config SOC_IMX21
bool
- select COMMON_CLK
select CPU_ARM926T
select IMX_HAVE_IOMUX_V1
select MXC_AVIC
bool
select ARCH_MX25
select ARCH_MXC_IOMUX_V3
- select COMMON_CLK
select CPU_ARM926T
select MXC_AVIC
bool
select ARCH_HAS_CPUFREQ
select ARCH_HAS_OPP
- select COMMON_CLK
select CPU_ARM926T
select IMX_HAVE_IOMUX_V1
select MACH_MX27
config SOC_IMX31
bool
- select COMMON_CLK
select CPU_V6
select IMX_HAVE_PLATFORM_MXC_RNGA
select MXC_AVIC
config SOC_IMX35
bool
select ARCH_MXC_IOMUX_V3
- select COMMON_CLK
select CPU_V6K
select HAVE_EPIT
select MXC_AVIC
select ARCH_HAS_CPUFREQ
select ARCH_HAS_OPP
select ARCH_MXC_IOMUX_V3
- select COMMON_CLK
select CPU_V7
select MXC_TZIC
select ARM_ERRATA_764369 if SMP
select ARM_ERRATA_775420
select ARM_GIC
- select COMMON_CLK
select CPU_V7
select HAVE_ARM_SCU if SMP
select HAVE_ARM_TWD if SMP
#include <linux/clk.h>
#include <linux/io.h>
#include <linux/clkdev.h>
+#include <linux/clk-provider.h>
#include <linux/of.h>
#include <linux/err.h>
{
int i;
- of_clk_init(NULL);
-
clk[dummy] = imx_clk_fixed("dummy", 0);
clk[ckil] = imx_obtain_fixed_clock("ckil", rate_ckil);
clk[osc] = imx_obtain_fixed_clock("osc", rate_osc);
return 0;
}
-int __init mx53_clocks_init(unsigned long rate_ckil, unsigned long rate_osc,
- unsigned long rate_ckih1, unsigned long rate_ckih2)
+static void __init mx51_clocks_init_dt(struct device_node *np)
+{
+ mx51_clocks_init(0, 0, 0, 0);
+}
+CLK_OF_DECLARE(imx51_ccm, "fsl,imx51-ccm", mx51_clocks_init_dt);
+
+static void __init mx53_clocks_init(struct device_node *np)
{
int i;
unsigned long r;
- struct device_node *np;
clk[pll1_sw] = imx_clk_pllv2("pll1_sw", "osc", MX53_DPLL1_BASE);
clk[pll2_sw] = imx_clk_pllv2("pll2_sw", "osc", MX53_DPLL2_BASE);
pr_err("i.MX53 clk %d: register failed with %ld\n",
i, PTR_ERR(clk[i]));
- np = of_find_compatible_node(NULL, NULL, "fsl,imx53-ccm");
clk_data.clks = clk;
clk_data.clk_num = ARRAY_SIZE(clk);
of_clk_add_provider(np, of_clk_src_onecell_get, &clk_data);
- mx5_clocks_common_init(rate_ckil, rate_osc, rate_ckih1, rate_ckih2);
+ mx5_clocks_common_init(0, 0, 0, 0);
clk_register_clkdev(clk[vpu_gate], NULL, "imx53-vpu.0");
clk_register_clkdev(clk[i2c3_gate], NULL, "imx21-i2c.2");
r = clk_round_rate(clk[usboh3_per_gate], 54000000);
clk_set_rate(clk[usboh3_per_gate], r);
-
- return 0;
-}
-
-int __init mx51_clocks_init_dt(void)
-{
- return mx51_clocks_init(0, 0, 0, 0);
-}
-
-int __init mx53_clocks_init_dt(void)
-{
- return mx53_clocks_init(0, 0, 0, 0);
}
+CLK_OF_DECLARE(imx53_ccm, "fsl,imx53-ccm", mx53_clocks_init);
extern int mx35_clocks_init(void);
extern int mx51_clocks_init(unsigned long ckil, unsigned long osc,
unsigned long ckih1, unsigned long ckih2);
-extern int mx53_clocks_init(unsigned long ckil, unsigned long osc,
- unsigned long ckih1, unsigned long ckih2);
extern int mx25_clocks_init_dt(void);
extern int mx27_clocks_init_dt(void);
extern int mx31_clocks_init_dt(void);
-extern int mx51_clocks_init_dt(void);
-extern int mx53_clocks_init_dt(void);
extern struct platform_device *mxc_register_gpio(char *name, int id,
resource_size_t iobase, resource_size_t iosize, int irq, int irq_high);
extern void mxc_set_cpu_type(unsigned int type);
NULL
};
-static void __init imx51_timer_init(void)
-{
- mx51_clocks_init_dt();
-}
-
DT_MACHINE_START(IMX51_DT, "Freescale i.MX51 (Device Tree Support)")
.map_io = mx51_map_io,
.init_early = imx51_init_early,
.init_irq = mx51_init_irq,
.handle_irq = imx51_handle_irq,
- .init_time = imx51_timer_init,
.init_machine = imx51_dt_init,
.init_late = imx51_init_late,
.dt_compat = imx51_dt_board_compat,
NULL
};
-static void __init imx53_timer_init(void)
-{
- mx53_clocks_init_dt();
-}
-
DT_MACHINE_START(IMX53_DT, "Freescale i.MX53 (Device Tree Support)")
.map_io = mx53_map_io,
.init_early = imx53_init_early,
.init_irq = mx53_init_irq,
.handle_irq = imx53_handle_irq,
- .init_time = imx53_timer_init,
.init_machine = imx53_dt_init,
.init_late = imx53_init_late,
.dt_compat = imx53_dt_board_compat,
*/
#include <linux/clk.h>
-#include <linux/clk-provider.h>
#include <linux/clkdev.h>
-#include <linux/clocksource.h>
#include <linux/cpu.h>
#include <linux/delay.h>
#include <linux/export.h>
static void __init imx6q_init_machine(void)
{
+ imx_print_silicon_rev(cpu_is_imx6dl() ? "i.MX6DL" : "i.MX6Q",
+ imx6q_revision());
+
imx6q_enet_phy_init();
of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
irqchip_init();
}
-static void __init imx6q_timer_init(void)
-{
- of_clk_init(NULL);
- clocksource_of_init();
- imx_print_silicon_rev(cpu_is_imx6dl() ? "i.MX6DL" : "i.MX6Q",
- imx6q_revision());
-}
-
static const char *imx6q_dt_compat[] __initdata = {
"fsl,imx6dl",
"fsl,imx6q",
.smp = smp_ops(imx_smp_ops),
.map_io = imx6q_map_io,
.init_irq = imx6q_init_irq,
- .init_time = imx6q_timer_init,
.init_machine = imx6q_init_machine,
.init_late = imx6q_init_late,
.dt_compat = imx6q_dt_compat,
*
*/
-#include <linux/clk-provider.h>
#include <linux/irqchip.h>
#include <linux/of.h>
#include <linux/of_platform.h>
irqchip_init();
}
-static void __init imx6sl_timer_init(void)
-{
- of_clk_init(NULL);
-}
-
static const char *imx6sl_dt_compat[] __initdata = {
"fsl,imx6sl",
NULL,
DT_MACHINE_START(IMX6SL, "Freescale i.MX6 SoloLite (Device Tree)")
.map_io = debug_ll_io_init,
.init_irq = imx6sl_init_irq,
- .init_time = imx6sl_timer_init,
.init_machine = imx6sl_init_machine,
.dt_compat = imx6sl_dt_compat,
.restart = mxc_restart,
*/
#include <linux/of_platform.h>
-#include <linux/clocksource.h>
#include <linux/irqchip.h>
-#include <linux/clk-provider.h>
#include <asm/mach/arch.h>
#include <asm/hardware/cache-l2x0.h>
irqchip_init();
}
-static void __init vf610_init_time(void)
-{
- of_clk_init(NULL);
- clocksource_of_init();
-}
-
static const char *vf610_dt_compat[] __initdata = {
"fsl,vf610",
NULL,
DT_MACHINE_START(VYBRID_VF610, "Freescale Vybrid VF610 (Device Tree)")
.init_irq = vf610_init_irq,
- .init_time = vf610_init_time,
.init_machine = vf610_init_machine,
.dt_compat = vf610_dt_compat,
.restart = mxc_restart,
#include <linux/of.h>
#include <linux/of_platform.h>
#include <linux/clk-provider.h>
-#include <linux/clocksource.h>
#include <linux/dma-mapping.h>
#include <linux/irqchip.h>
#include <linux/kexec.h>
clk_prepare_enable(clk);
}
-static void __init kirkwood_dt_time_init(void)
-{
- of_clk_init(NULL);
- clocksource_of_init();
-}
-
static void __init kirkwood_dt_init_early(void)
{
mvebu_mbus_init("marvell,kirkwood-mbus",
writel(readl(CPU_CONFIG) & ~CPU_CONFIG_ERROR_PROP, CPU_CONFIG);
BUG_ON(mvebu_mbus_dt_init());
- kirkwood_setup_wins();
kirkwood_l2_init();
/* Maintainer: Jason Cooper <jason@lakedaemon.net> */
.map_io = kirkwood_map_io,
.init_early = kirkwood_dt_init_early,
- .init_time = kirkwood_dt_time_init,
.init_machine = kirkwood_dt_init,
.restart = kirkwood_restart,
.dt_compat = kirkwood_dt_board_compat,
#include <linux/clk.h>
#include <linux/clk/mxs.h>
#include <linux/clkdev.h>
-#include <linux/clocksource.h>
-#include <linux/clk-provider.h>
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/gpio.h>
soft_restart(0);
}
-static void __init mxs_timer_init(void)
-{
- if (of_machine_is_compatible("fsl,imx23"))
- mx23_clocks_init();
- else
- mx28_clocks_init();
- of_clk_init(NULL);
- clocksource_of_init();
-}
-
static const char *mxs_dt_compat[] __initdata = {
"fsl,imx28",
"fsl,imx23",
DT_MACHINE_START(MXS, "Freescale MXS (Device Tree)")
.handle_irq = icoll_handle_irq,
- .init_time = mxs_timer_init,
.init_machine = mxs_machine_init,
.init_late = mxs_pm_init,
.dt_compat = mxs_dt_compat,
#include <linux/slab.h>
#include <linux/irq.h>
#include <linux/dma-mapping.h>
-#include <linux/platform_data/clk-nomadik.h>
-#include <linux/clocksource.h>
#include <linux/of_irq.h>
#include <linux/of_gpio.h>
#include <linux/of_address.h>
#include <linux/of_platform.h>
-#include <linux/mtd/fsmc.h>
#include <linux/gpio.h>
-#include <linux/amba/mmci.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
writel(1, srcbase + 0x18);
}
-/* Initial value for SRC control register: all timers use MXTAL/8 source */
-#define SRC_CR_INIT_MASK 0x00007fff
-#define SRC_CR_INIT_VAL 0x2aaa8000
-
-static void __init cpu8815_timer_init_of(void)
-{
- struct device_node *mtu;
- void __iomem *base;
- int irq;
- u32 src_cr;
-
- /* We need this to be up now */
- nomadik_clk_init();
-
- mtu = of_find_node_by_path("/mtu@101e2000");
- if (!mtu)
- return;
- base = of_iomap(mtu, 0);
- if (WARN_ON(!base))
- return;
- irq = irq_of_parse_and_map(mtu, 0);
-
- pr_info("Remapped MTU @ %p, irq: %d\n", base, irq);
-
- /* Configure timer sources in "system reset controller" ctrl reg */
- src_cr = readl(base);
- src_cr &= SRC_CR_INIT_MASK;
- src_cr |= SRC_CR_INIT_VAL;
- writel(src_cr, base);
-
- clocksource_of_init();
-}
-
-static struct fsmc_nand_timings cpu8815_nand_timings = {
- .thiz = 0,
- .thold = 0x10,
- .twait = 0x0A,
- .tset = 0,
-};
-
-static struct fsmc_nand_platform_data cpu8815_nand_data = {
- .nand_timings = &cpu8815_nand_timings,
-};
-
/*
* The SMSC911x IRQ is connected to a GPIO pin, but the driver expects
* to simply request an IRQ passed as a resource. So the GPIO pin needs
}
device_initcall(cpu8815_eth_init);
-/*
- * TODO:
- * cannot be set from device tree, convert to a proper DT
- * binding.
- */
-static struct mmci_platform_data mmcsd_plat_data = {
- .ocr_mask = MMC_VDD_29_30,
-};
-
/*
* This GPIO pin turns on a line that is used to detect card insertion
* on this board.
}
device_initcall(cpu8815_mmcsd_init);
-
-/* These are mostly to get the right device names for the clock lookups */
-static struct of_dev_auxdata cpu8815_auxdata_lookup[] __initdata = {
- OF_DEV_AUXDATA("stericsson,fsmc-nand", NOMADIK_FSMC_BASE,
- NULL, &cpu8815_nand_data),
- OF_DEV_AUXDATA("arm,primecell", NOMADIK_SDI_BASE,
- NULL, &mmcsd_plat_data),
- { /* sentinel */ },
-};
-
static void __init cpu8815_init_of(void)
{
#ifdef CONFIG_CACHE_L2X0
/* At full speed latency must be >=2, so 0x249 in low bits */
l2x0_of_init(0x00730249, 0xfe000fff);
#endif
- of_platform_populate(NULL, of_default_bus_match_table,
- cpu8815_auxdata_lookup, NULL);
+ of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
}
static const char * cpu8815_board_compat[] = {
DT_MACHINE_START(NOMADIK_DT, "Nomadik STn8815")
.map_io = cpu8815_map_io,
- .init_time = cpu8815_timer_init_of,
.init_machine = cpu8815_init_of,
.restart = cpu8815_restart,
.dt_compat = cpu8815_board_compat,
#include <linux/of_platform.h>
#include <linux/irqchip.h>
#include <linux/irqchip/arm-vic.h>
-#include <linux/clk-provider.h>
#include <linux/clkdev.h>
#include <linux/amba/bus.h>
#include <linux/amba/clcd.h>
-#include <linux/clocksource.h>
#include <asm/mach/arch.h>
#include <asm/mach-types.h>
nspire_auxdata, NULL);
}
-static void __init nspire_init_time(void)
-{
- of_clk_init(NULL);
- clocksource_of_init();
-}
-
static void nspire_restart(char mode, const char *cmd)
{
void __iomem *base = ioremap(NSPIRE_MISC_PHYS_BASE, SZ_4K);
DT_MACHINE_START(NSPIRE, "TI-NSPIRE")
.dt_compat = nspire_dt_match,
.map_io = nspire_map_io,
- .init_time = nspire_init_time,
.init_machine = nspire_init,
.restart = nspire_restart,
MACHINE_END
select CPU_V6
select MULTI_IRQ_HANDLER
select SOC_HAS_OMAP2_SDRC
- select COMMON_CLK
config ARCH_OMAP3
bool "TI OMAP3"
select PM_OPP if PM
select PM_RUNTIME if CPU_IDLE
select SOC_HAS_OMAP2_SDRC
- select COMMON_CLK
select USB_ARCH_HAS_EHCI if USB_SUPPORT
config ARCH_OMAP4
select PM_OPP if PM
select PM_RUNTIME if CPU_IDLE
select USB_ARCH_HAS_EHCI if USB_SUPPORT
- select COMMON_CLK
select ARM_ERRATA_754322
select ARM_ERRATA_775420
select HAVE_ARM_SCU if SMP
select HAVE_ARM_TWD if LOCAL_TIMERS
select HAVE_SMP
- select COMMON_CLK
select HAVE_ARM_ARCH_TIMER
select ARM_ERRATA_798181 if SMP
select ARM_CPU_SUSPEND if PM
select CPU_V7
select MULTI_IRQ_HANDLER
- select COMMON_CLK
config SOC_AM43XX
bool "TI AM43x"
select ARCH_OMAP2PLUS
select MULTI_IRQ_HANDLER
select ARM_GIC
- select COMMON_CLK
select MACH_OMAP_GENERIC
config ARCH_OMAP2PLUS
select ARCH_HAS_HOLES_MEMORYMODEL
select ARCH_OMAP
select ARCH_REQUIRE_GPIOLIB
- select CLKDEV_LOOKUP
select CLKSRC_MMIO
+ select COMMON_CLK
select GENERIC_CLOCKEVENTS
select GENERIC_IRQ_CHIP
- select HAVE_CLK
select OMAP_DM_TIMER
select PINCTRL
select PROC_DEVICETREE if PROC_FS
.restart = omap3xxx_restart,
MACHINE_END
+static const char *omap36xx_boards_compat[] __initdata = {
+ "ti,omap36xx",
+ NULL,
+};
+
+DT_MACHINE_START(OMAP36XX_DT, "Generic OMAP36xx (Flattened Device Tree)")
+ .reserve = omap_reserve,
+ .map_io = omap3_map_io,
+ .init_early = omap3630_init_early,
+ .init_irq = omap_intc_of_init,
+ .handle_irq = omap3_intc_handle_irq,
+ .init_machine = omap_generic_init,
+ .init_late = omap3_init_late,
+ .init_time = omap3_sync32k_timer_init,
+ .dt_compat = omap36xx_boards_compat,
+ .restart = omap3xxx_restart,
+MACHINE_END
+
static const char *omap3_gp_boards_compat[] __initdata = {
"ti,omap3-beagle",
"timll,omap3-devkit8000",
.name = "lp5523:kb1",
.chan_nr = 0,
.led_current = 50,
+ .max_current = 100,
}, {
.name = "lp5523:kb2",
.chan_nr = 1,
.led_current = 50,
+ .max_current = 100,
}, {
.name = "lp5523:kb3",
.chan_nr = 2,
.led_current = 50,
+ .max_current = 100,
}, {
.name = "lp5523:kb4",
.chan_nr = 3,
.led_current = 50,
+ .max_current = 100,
}, {
.name = "lp5523:b",
.chan_nr = 4,
.led_current = 50,
+ .max_current = 100,
}, {
.name = "lp5523:g",
.chan_nr = 5,
.led_current = 50,
+ .max_current = 100,
}, {
.name = "lp5523:r",
.chan_nr = 6,
.led_current = 50,
+ .max_current = 100,
}, {
.name = "lp5523:kb5",
.chan_nr = 7,
.led_current = 50,
+ .max_current = 100,
}, {
.name = "lp5523:kb6",
.chan_nr = 8,
.led_current = 50,
+ .max_current = 100,
}
};
struct gpmc_timings t;
int ret;
- if (gpmc_onenand_data->of_node)
+ if (gpmc_onenand_data->of_node) {
gpmc_read_settings_dt(gpmc_onenand_data->of_node,
&onenand_async);
+ if (onenand_async.sync_read || onenand_async.sync_write) {
+ if (onenand_async.sync_write)
+ gpmc_onenand_data->flags |=
+ ONENAND_SYNC_READWRITE;
+ else
+ gpmc_onenand_data->flags |= ONENAND_SYNC_READ;
+ onenand_async.sync_read = false;
+ onenand_async.sync_write = false;
+ }
+ }
omap2_onenand_set_async_mode(onenand_base);
#define OMAP_PULL_UP (1 << 4)
#define OMAP_ALTELECTRICALSEL (1 << 5)
-/* 34xx specific mux bit defines */
+/* omap3/4/5 specific mux bit defines */
#define OMAP_INPUT_EN (1 << 8)
#define OMAP_OFF_EN (1 << 9)
#define OMAP_OFFOUT_EN (1 << 10)
#define OMAP_OFF_PULL_EN (1 << 12)
#define OMAP_OFF_PULL_UP (1 << 13)
#define OMAP_WAKEUP_EN (1 << 14)
-
-/* 44xx specific mux bit defines */
#define OMAP_WAKEUP_EVENT (1 << 15)
/* Active pin states */
#endif /* CONFIG_HAVE_ARM_TWD */
#endif /* CONFIG_ARCH_OMAP4 */
-#ifdef CONFIG_SOC_OMAP5
+#if defined(CONFIG_SOC_OMAP5) || defined(CONFIG_SOC_DRA7XX)
void __init omap5_realtime_timer_init(void)
{
omap4_sync32k_timer_init();
clocksource_of_init();
}
-#endif /* CONFIG_SOC_OMAP5 */
+#endif /* CONFIG_SOC_OMAP5 || CONFIG_SOC_DRA7XX */
/**
* omap_timer_init - build and register timer device with an
* Licensed under GPLv2 or later.
*/
-#include <linux/clocksource.h>
#include <linux/init.h>
#include <linux/kernel.h>
#include <asm/sizes.h>
sirfsoc_pm_init();
}
-static __init void sirfsoc_init_time(void)
-{
- /* initialize clocking early, we want to set the OS timer */
- sirfsoc_of_clk_init();
- clocksource_of_init();
-}
-
static __init void sirfsoc_map_io(void)
{
sirfsoc_map_lluart();
DT_MACHINE_START(ATLAS6_DT, "Generic ATLAS6 (Flattened Device Tree)")
/* Maintainer: Barry Song <baohua.song@csr.com> */
.map_io = sirfsoc_map_io,
- .init_time = sirfsoc_init_time,
.init_late = sirfsoc_init_late,
.dt_compat = atlas6_dt_match,
.restart = sirfsoc_restart,
DT_MACHINE_START(PRIMA2_DT, "Generic PRIMA2 (Flattened Device Tree)")
/* Maintainer: Barry Song <baohua.song@csr.com> */
.map_io = sirfsoc_map_io,
- .init_time = sirfsoc_init_time,
.dma_zone_size = SZ_256M,
.init_late = sirfsoc_init_late,
.dt_compat = prima2_dt_match,
/* Maintainer: Barry Song <baohua.song@csr.com> */
.smp = smp_ops(sirfsoc_smp_ops),
.map_io = sirfsoc_map_io,
- .init_time = sirfsoc_init_time,
.init_late = sirfsoc_init_late,
.dt_compat = marco_dt_match,
.restart = sirfsoc_restart,
extern void sirfsoc_cpu_die(unsigned int cpu);
extern void __init sirfsoc_of_irq_init(void);
-extern void __init sirfsoc_of_clk_init(void);
extern void sirfsoc_restart(enum reboot_mode, const char *);
extern asmlinkage void __exception_irq_entry sirfsoc_handle_irq(struct pt_regs *regs);
#include <linux/init.h>
#include <linux/of_platform.h>
#include <linux/irqchip.h>
-#include <linux/dw_apb_timer.h>
-#include <linux/clk-provider.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/hardware/cache-l2x0.h>
-static void __init rockchip_timer_init(void)
-{
- of_clk_init(NULL);
- clocksource_of_init();
-}
-
static void __init rockchip_dt_init(void)
{
l2x0_of_init(0, ~0UL);
DT_MACHINE_START(ROCKCHIP_DT, "Rockchip Cortex-A9 (Device Tree)")
.init_machine = rockchip_dt_init,
- .init_time = rockchip_timer_init,
.dt_compat = rockchip_board_dt_compat,
MACHINE_END
select SAMSUNG_GPIO_EXTRA128
help
Machine support for the Wolfson Cragganmore S3C6410 variant.
+
+config MACH_S3C64XX_DT
+ bool "Samsung S3C6400/S3C6410 machine using Device Tree"
+ select CLKSRC_OF
+ select CPU_S3C6400
+ select CPU_S3C6410
+ select PINCTRL
+ select PINCTRL_S3C64XX
+ select USE_OF
+ help
+ Machine support for Samsung S3C6400/S3C6410 machines with Device Tree
+ enabled.
+ Select this if a fdt blob is available for your S3C64XX SoC based
+ board.
+ Note: This is under development and not all peripherals can be
+ supported with this machine file.
obj-$(CONFIG_MACH_SMDK6400) += mach-smdk6400.o
obj-$(CONFIG_MACH_SMDK6410) += mach-smdk6410.o
obj-$(CONFIG_MACH_WLF_CRAGG_6410) += mach-crag6410.o mach-crag6410-module.o
+obj-$(CONFIG_MACH_S3C64XX_DT) += mach-s3c64xx-dt.o
* published by the Free Software Foundation.
*/
+/*
+ * NOTE: Code in this file is not used when booting with Device Tree support.
+ */
+
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/module.h>
static __init int s3c64xx_dev_init(void)
{
+ /* Not applicable when using DT. */
+ if (of_have_populated_dt())
+ return 0;
+
subsys_system_register(&s3c64xx_subsys, NULL);
return device_register(&s3c64xx_dev);
}
{
int irq;
+ /* On DT-enabled systems EINTs are handled by pinctrl-s3c64xx driver. */
+ if (of_have_populated_dt())
+ return -ENODEV;
+
for (irq = IRQ_EINT(0); irq <= IRQ_EINT(27); irq++) {
irq_set_chip_and_handler(irq, &s3c_irq_eint, handle_level_irq);
irq_set_chip_data(irq, (void *)eint_irq_to_bit(irq));
* published by the Free Software Foundation.
*/
+/*
+ * NOTE: Code in this file is not used when booting with Device Tree support.
+ */
+
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/interrupt.h>
#include <linux/err.h>
#include <linux/io.h>
#include <linux/amba/pl080.h>
+#include <linux/of.h>
#include <mach/dma.h>
#include <mach/map.h>
{
int ret;
+ /* This driver is not supported when booting with device tree. */
+ if (of_have_populated_dt())
+ return -ENODEV;
+
printk(KERN_INFO "%s: Registering DMA channels\n", __func__);
dma_pool = dma_pool_create("DMA-LLI", NULL, sizeof(struct pl080s_lli), 16, 0);
* published by the Free Software Foundation.
*/
+/*
+ * NOTE: Code in this file is not used when booting with Device Tree support.
+ */
+
#include <linux/kernel.h>
#include <linux/syscore_ops.h>
#include <linux/interrupt.h>
#include <linux/serial_core.h>
#include <linux/irq.h>
#include <linux/io.h>
+#include <linux/of.h>
#include <mach/map.h>
static __init int s3c64xx_syscore_init(void)
{
+ /* Appropriate drivers (pinctrl, uart) handle this when using DT. */
+ if (of_have_populated_dt())
+ return 0;
+
register_syscore_ops(&s3c64xx_irq_syscore_ops);
return 0;
--- /dev/null
+/*
+ * Samsung's S3C64XX flattened device tree enabled machine
+ *
+ * Copyright (c) 2013 Tomasz Figa <tomasz.figa@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/clk-provider.h>
+#include <linux/irqchip.h>
+#include <linux/of_platform.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/system_misc.h>
+
+#include <plat/cpu.h>
+#include <plat/watchdog-reset.h>
+
+#include <mach/map.h>
+
+#include "common.h"
+
+/*
+ * IO mapping for shared system controller IP.
+ *
+ * FIXME: Make remaining drivers use dynamic mapping.
+ */
+static struct map_desc s3c64xx_dt_iodesc[] __initdata = {
+ {
+ .virtual = (unsigned long)S3C_VA_SYS,
+ .pfn = __phys_to_pfn(S3C64XX_PA_SYSCON),
+ .length = SZ_4K,
+ .type = MT_DEVICE,
+ },
+};
+
+static void __init s3c64xx_dt_map_io(void)
+{
+ debug_ll_io_init();
+ iotable_init(s3c64xx_dt_iodesc, ARRAY_SIZE(s3c64xx_dt_iodesc));
+
+ s3c64xx_init_cpu();
+
+ if (!soc_is_s3c64xx())
+ panic("SoC is not S3C64xx!");
+}
+
+static void __init s3c64xx_dt_init_irq(void)
+{
+ of_clk_init(NULL);
+ samsung_wdt_reset_of_init();
+ irqchip_init();
+};
+
+static void __init s3c64xx_dt_init_machine(void)
+{
+ of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
+}
+
+static void s3c64xx_dt_restart(enum reboot_mode mode, const char *cmd)
+{
+ if (mode != REBOOT_SOFT)
+ samsung_wdt_reset();
+
+ /* if all else fails, or mode was for soft, jump to 0 */
+ soft_restart(0);
+}
+
+static char const *s3c64xx_dt_compat[] __initdata = {
+ "samsung,s3c6400",
+ "samsung,s3c6410",
+ NULL
+};
+
+DT_MACHINE_START(S3C6400_DT, "Samsung S3C64xx (Flattened Device Tree)")
+ /* Maintainer: Tomasz Figa <tomasz.figa@gmail.com> */
+ .dt_compat = s3c64xx_dt_compat,
+ .map_io = s3c64xx_dt_map_io,
+ .init_irq = s3c64xx_dt_init_irq,
+ .init_machine = s3c64xx_dt_init_machine,
+ .restart = s3c64xx_dt_restart,
+MACHINE_END
* published by the Free Software Foundation.
*/
+/*
+ * NOTE: Code in this file is not used when booting with Device Tree support.
+ */
+
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/interrupt.h>
#include <linux/device.h>
#include <linux/serial_core.h>
#include <linux/platform_device.h>
+#include <linux/of.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
static int __init s3c6400_core_init(void)
{
+ /* Not applicable when using DT. */
+ if (of_have_populated_dt())
+ return 0;
+
return subsys_system_register(&s3c6400_subsys, NULL);
}
* published by the Free Software Foundation.
*/
+/*
+ * NOTE: Code in this file is not used when booting with Device Tree support.
+ */
+
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/interrupt.h>
#include <linux/device.h>
#include <linux/serial_core.h>
#include <linux/platform_device.h>
+#include <linux/of.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
static int __init s3c6410_core_init(void)
{
+ /* Not applicable when using DT. */
+ if (of_have_populated_dt())
+ return 0;
+
return subsys_system_register(&s3c6410_subsys, NULL);
}
+++ /dev/null
-#
-# Makefile for the linux kernel.
-#
-
-# Object file lists.
-
-obj-y := core.o dma.o irq.o pci.o leds.o
-obj-m :=
-obj-n :=
-obj- :=
+++ /dev/null
- zreladdr-y += 0x08008000
-
+++ /dev/null
-/*
- * linux/arch/arm/mach-shark/arch.c
- *
- * Architecture specific stuff.
- */
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-#include <linux/sched.h>
-#include <linux/serial_8250.h>
-#include <linux/io.h>
-#include <linux/cpu.h>
-#include <linux/reboot.h>
-
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/param.h>
-#include <asm/system_misc.h>
-
-#include <asm/mach/map.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-
-#define ROMCARD_SIZE 0x08000000
-#define ROMCARD_START 0x10000000
-
-static void shark_restart(enum reboot_mode mode, const char *cmd)
-{
- short temp;
- /* Reset the Machine via pc[3] of the sequoia chipset */
- outw(0x09,0x24);
- temp=inw(0x26);
- temp = temp | (1<<3) | (1<<10);
- outw(0x09,0x24);
- outw(temp,0x26);
-}
-
-static struct plat_serial8250_port serial_platform_data[] = {
- {
- .iobase = 0x3f8,
- .irq = 4,
- .uartclk = 1843200,
- .regshift = 0,
- .iotype = UPIO_PORT,
- .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
- },
- {
- .iobase = 0x2f8,
- .irq = 3,
- .uartclk = 1843200,
- .regshift = 0,
- .iotype = UPIO_PORT,
- .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
- },
- { },
-};
-
-static struct platform_device serial_device = {
- .name = "serial8250",
- .id = PLAT8250_DEV_PLATFORM,
- .dev = {
- .platform_data = serial_platform_data,
- },
-};
-
-static struct resource rtc_resources[] = {
- [0] = {
- .start = 0x70,
- .end = 0x73,
- .flags = IORESOURCE_IO,
- },
- [1] = {
- .start = IRQ_ISA_RTC_ALARM,
- .end = IRQ_ISA_RTC_ALARM,
- .flags = IORESOURCE_IRQ,
- }
-};
-
-static struct platform_device rtc_device = {
- .name = "rtc_cmos",
- .id = -1,
- .resource = rtc_resources,
- .num_resources = ARRAY_SIZE(rtc_resources),
-};
-
-static int __init shark_init(void)
-{
- int ret;
-
- if (machine_is_shark())
- {
- ret = platform_device_register(&rtc_device);
- if (ret) printk(KERN_ERR "Unable to register RTC device: %d\n", ret);
- ret = platform_device_register(&serial_device);
- if (ret) printk(KERN_ERR "Unable to register Serial device: %d\n", ret);
- }
- return 0;
-}
-
-arch_initcall(shark_init);
-
-extern void shark_init_irq(void);
-
-#define IRQ_TIMER 0
-#define HZ_TIME ((1193180 + HZ/2) / HZ)
-
-static irqreturn_t
-shark_timer_interrupt(int irq, void *dev_id)
-{
- timer_tick();
- return IRQ_HANDLED;
-}
-
-static struct irqaction shark_timer_irq = {
- .name = "Shark Timer Tick",
- .flags = IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL,
- .handler = shark_timer_interrupt,
-};
-
-/*
- * Set up timer interrupt, and return the current time in seconds.
- */
-static void __init shark_timer_init(void)
-{
- outb(0x34, 0x43); /* binary, mode 0, LSB/MSB, Ch 0 */
- outb(HZ_TIME & 0xff, 0x40); /* LSB of count */
- outb(HZ_TIME >> 8, 0x40);
-
- setup_irq(IRQ_TIMER, &shark_timer_irq);
-}
-
-static void shark_init_early(void)
-{
- cpu_idle_poll_ctrl(true);
-}
-
-MACHINE_START(SHARK, "Shark")
- /* Maintainer: Alexander Schulz */
- .atag_offset = 0x3000,
- .init_early = shark_init_early,
- .init_irq = shark_init_irq,
- .init_time = shark_timer_init,
- .dma_zone_size = SZ_4M,
- .restart = shark_restart,
-MACHINE_END
+++ /dev/null
-/*
- * linux/arch/arm/mach-shark/dma.c
- *
- * by Alexander Schulz
- *
- * derived from:
- * arch/arm/kernel/dma-ebsa285.c
- * Copyright (C) 1998 Phil Blundell
- */
-
-#include <linux/init.h>
-
-#include <asm/dma.h>
-#include <asm/mach/dma.h>
-
-static int __init shark_dma_init(void)
-{
-#ifdef CONFIG_ISA_DMA
- isa_init_dma();
-#endif
- return 0;
-}
-core_initcall(shark_dma_init);
+++ /dev/null
-/* arch/arm/mach-shark/include/mach/debug-macro.S
- *
- * Debugging macro include header
- *
- * Copyright (C) 1994-1999 Russell King
- * Moved from linux/arch/arm/kernel/debug.S by Ben Dooks
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
-*/
-
- .macro addruart, rp, rv, tmp
- mov \rp, #0x3f8
- orr \rv, \rp, #0xfe000000
- orr \rv, \rv, #0x00e00000
- orr \rp, \rp, #0x40000000
- .endm
-
- .macro senduart,rd,rx
- strb \rd, [\rx]
- .endm
-
- .macro waituart,rd,rx
- .endm
-
- .macro busyuart,rd,rx
- mov \rd, #0
-1001: add \rd, \rd, #1
- teq \rd, #0x10000
- bne 1001b
- .endm
-
+++ /dev/null
-/*
- * arch/arm/mach-shark/include/mach/entry-macro.S
- *
- * Low-level IRQ helper macros for Shark platform
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
- .macro get_irqnr_preamble, base, tmp
- mov \base, #0xfe000000
- orr \base, \base, #0x00e00000
- .endm
-
- .macro get_irqnr_and_base, irqnr, irqstat, base, tmp
-
- mov \irqstat, #0x0C
- strb \irqstat, [\base, #0x20] @outb(0x0C, 0x20) /* Poll command */
- ldrb \irqnr, [\base, #0x20] @irq = inb(0x20) & 7
- and \irqstat, \irqnr, #0x80
- teq \irqstat, #0
- beq 43f
- and \irqnr, \irqnr, #7
- teq \irqnr, #2
- bne 44f
-43: mov \irqstat, #0x0C
- strb \irqstat, [\base, #0xa0] @outb(0x0C, 0xA0) /* Poll command */
- ldrb \irqnr, [\base, #0xa0] @irq = (inb(0xA0) & 7) + 8
- and \irqstat, \irqnr, #0x80
- teq \irqstat, #0
- beq 44f
- and \irqnr, \irqnr, #7
- add \irqnr, \irqnr, #8
-44: teq \irqstat, #0
- .endm
-
+++ /dev/null
-/*
- * arch/arm/mach-shark/include/mach/framebuffer.h
- *
- * by Alexander Schulz
- *
- */
-
-#ifndef __ASM_ARCH_FRAMEBUFFER_H
-#define __ASM_ARCH_FRAMEBUFFER_H
-
-/* defines for the Framebuffer */
-#define FB_START 0x06000000
-#define FB_SIZE 0x01000000
-
-#endif
-
+++ /dev/null
-/*
- * arch/arm/mach-shark/include/mach/hardware.h
- *
- * by Alexander Schulz
- *
- * derived from:
- * arch/arm/mach-ebsa110/include/mach/hardware.h
- * Copyright (C) 1996-1999 Russell King.
- */
-#ifndef __ASM_ARCH_HARDWARE_H
-#define __ASM_ARCH_HARDWARE_H
-
-#define UNCACHEABLE_ADDR 0xdf010000
-
-#endif
-
+++ /dev/null
-/*
- * arch/arm/mach-shark/include/mach/irqs.h
- *
- * by Alexander Schulz
- */
-
-#define NR_IRQS 16
-
-#define IRQ_ISA_KEYBOARD 1
-#define IRQ_ISA_RTC_ALARM 8
-#define I8042_KBD_IRQ 1
-#define I8042_AUX_IRQ 12
-#define IRQ_HARDDISK 14
+++ /dev/null
-/*
- * arch/arm/mach-shark/include/mach/isa-dma.h
- *
- * by Alexander Schulz
- */
-#ifndef __ASM_ARCH_DMA_H
-#define __ASM_ARCH_DMA_H
-
-#define MAX_DMA_CHANNELS 8
-#define DMA_ISA_CASCADE 4
-
-#endif /* _ASM_ARCH_DMA_H */
-
+++ /dev/null
-/*
- * arch/arm/mach-shark/include/mach/memory.h
- *
- * by Alexander Schulz
- *
- * derived from:
- * arch/arm/mach-ebsa110/include/mach/memory.h
- * Copyright (c) 1996-1999 Russell King.
- */
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-#include <asm/sizes.h>
-
-/*
- * Physical DRAM offset.
- */
-#define PLAT_PHYS_OFFSET UL(0x08000000)
-
-/*
- * Cache flushing area
- */
-#define FLUSH_BASE_PHYS 0x80000000
-#define FLUSH_BASE 0xdf000000
-
-#endif
+++ /dev/null
-/*
- * arch/arm/mach-shark/include/mach/timex.h
- *
- * by Alexander Schulz
- */
-
-#define CLOCK_TICK_RATE 1193180
+++ /dev/null
-/*
- * arch/arm/mach-shark/include/mach/uncompress.h
- * by Alexander Schulz
- *
- * derived from:
- * arch/arm/mach-footbridge/include/mach/uncompress.h
- * Copyright (C) 1996,1997,1998 Russell King
- */
-
-#define SERIAL_BASE ((volatile unsigned char *)0x400003f8)
-
-static inline void putc(int c)
-{
- volatile int t;
-
- SERIAL_BASE[0] = c;
- t=0x10000;
- while (t--);
-}
-
-static inline void flush(void)
-{
-}
-
-#ifdef DEBUG
-static void putn(unsigned long z)
-{
- int i;
- char x;
-
- putc('0');
- putc('x');
- for (i=0;i<8;i++) {
- x='0'+((z>>((7-i)*4))&0xf);
- if (x>'9') x=x-'0'+'A'-10;
- putc(x);
- }
-}
-
-static void putr()
-{
- putc('\n');
- putc('\r');
-}
-#endif
-
-/*
- * nothing to do
- */
-#define arch_decomp_setup()
+++ /dev/null
-/*
- * linux/arch/arm/mach-shark/irq.c
- *
- * by Alexander Schulz
- *
- * derived from linux/arch/ppc/kernel/i8259.c and:
- * arch/arm/mach-ebsa110/include/mach/irq.h
- * Copyright (C) 1996-1998 Russell King
- */
-
-#include <linux/init.h>
-#include <linux/fs.h>
-#include <linux/interrupt.h>
-#include <linux/io.h>
-
-#include <asm/irq.h>
-#include <asm/mach/irq.h>
-
-/*
- * 8259A PIC functions to handle ISA devices:
- */
-
-/*
- * This contains the irq mask for both 8259A irq controllers,
- * Let through the cascade-interrupt no. 2 (ff-(1<<2)==fb)
- */
-static unsigned char cached_irq_mask[2] = { 0xfb, 0xff };
-
-/*
- * These have to be protected by the irq controller spinlock
- * before being called.
- */
-static void shark_disable_8259A_irq(struct irq_data *d)
-{
- unsigned int mask;
- if (d->irq<8) {
- mask = 1 << d->irq;
- cached_irq_mask[0] |= mask;
- outb(cached_irq_mask[1],0xA1);
- } else {
- mask = 1 << (d->irq-8);
- cached_irq_mask[1] |= mask;
- outb(cached_irq_mask[0],0x21);
- }
-}
-
-static void shark_enable_8259A_irq(struct irq_data *d)
-{
- unsigned int mask;
- if (d->irq<8) {
- mask = ~(1 << d->irq);
- cached_irq_mask[0] &= mask;
- outb(cached_irq_mask[0],0x21);
- } else {
- mask = ~(1 << (d->irq-8));
- cached_irq_mask[1] &= mask;
- outb(cached_irq_mask[1],0xA1);
- }
-}
-
-static void shark_ack_8259A_irq(struct irq_data *d){}
-
-static irqreturn_t bogus_int(int irq, void *dev_id)
-{
- printk("Got interrupt %i!\n",irq);
- return IRQ_NONE;
-}
-
-static struct irqaction cascade;
-
-static struct irq_chip fb_chip = {
- .name = "XT-PIC",
- .irq_ack = shark_ack_8259A_irq,
- .irq_mask = shark_disable_8259A_irq,
- .irq_unmask = shark_enable_8259A_irq,
-};
-
-void __init shark_init_irq(void)
-{
- int irq;
-
- for (irq = 0; irq < NR_IRQS; irq++) {
- irq_set_chip_and_handler(irq, &fb_chip, handle_edge_irq);
- set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
- }
-
- /* init master interrupt controller */
- outb(0x11, 0x20); /* Start init sequence, edge triggered (level: 0x19)*/
- outb(0x00, 0x21); /* Vector base */
- outb(0x04, 0x21); /* Cascade (slave) on IRQ2 */
- outb(0x03, 0x21); /* Select 8086 mode , auto eoi*/
- outb(0x0A, 0x20);
- /* init slave interrupt controller */
- outb(0x11, 0xA0); /* Start init sequence, edge triggered */
- outb(0x08, 0xA1); /* Vector base */
- outb(0x02, 0xA1); /* Cascade (slave) on IRQ2 */
- outb(0x03, 0xA1); /* Select 8086 mode, auto eoi */
- outb(0x0A, 0xA0);
- outb(cached_irq_mask[1],0xA1);
- outb(cached_irq_mask[0],0x21);
- //request_region(0x20,0x2,"pic1");
- //request_region(0xA0,0x2,"pic2");
-
- cascade.handler = bogus_int;
- cascade.name = "cascade";
- setup_irq(2,&cascade);
-}
-
+++ /dev/null
-/*
- * DIGITAL Shark LED control routines.
- *
- * Driver for the 3 user LEDs found on the Shark
- * Based on Versatile and RealView machine LED code
- *
- * License terms: GNU General Public License (GPL) version 2
- * Author: Bryan Wu <bryan.wu@canonical.com>
- */
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/io.h>
-#include <linux/ioport.h>
-#include <linux/slab.h>
-#include <linux/leds.h>
-
-#include <asm/mach-types.h>
-
-#if defined(CONFIG_NEW_LEDS) && defined(CONFIG_LEDS_CLASS)
-struct shark_led {
- struct led_classdev cdev;
- u8 mask;
-};
-
-/*
- * The triggers lines up below will only be used if the
- * LED triggers are compiled in.
- */
-static const struct {
- const char *name;
- const char *trigger;
-} shark_leds[] = {
- { "shark:amber0", "default-on", }, /* Bit 5 */
- { "shark:green", "heartbeat", }, /* Bit 6 */
- { "shark:amber1", "cpu0" }, /* Bit 7 */
-};
-
-static u16 led_reg_read(void)
-{
- outw(0x09, 0x24);
- return inw(0x26);
-}
-
-static void led_reg_write(u16 value)
-{
- outw(0x09, 0x24);
- outw(value, 0x26);
-}
-
-static void shark_led_set(struct led_classdev *cdev,
- enum led_brightness b)
-{
- struct shark_led *led = container_of(cdev,
- struct shark_led, cdev);
- u16 reg = led_reg_read();
-
- if (b != LED_OFF)
- reg |= led->mask;
- else
- reg &= ~led->mask;
-
- led_reg_write(reg);
-}
-
-static enum led_brightness shark_led_get(struct led_classdev *cdev)
-{
- struct shark_led *led = container_of(cdev,
- struct shark_led, cdev);
- u16 reg = led_reg_read();
-
- return (reg & led->mask) ? LED_FULL : LED_OFF;
-}
-
-static int __init shark_leds_init(void)
-{
- int i;
- u16 reg;
-
- if (!machine_is_shark())
- return -ENODEV;
-
- for (i = 0; i < ARRAY_SIZE(shark_leds); i++) {
- struct shark_led *led;
-
- led = kzalloc(sizeof(*led), GFP_KERNEL);
- if (!led)
- break;
-
- led->cdev.name = shark_leds[i].name;
- led->cdev.brightness_set = shark_led_set;
- led->cdev.brightness_get = shark_led_get;
- led->cdev.default_trigger = shark_leds[i].trigger;
-
- /* Count in 5 bits offset */
- led->mask = BIT(i + 5);
-
- if (led_classdev_register(NULL, &led->cdev) < 0) {
- kfree(led);
- break;
- }
- }
-
- /* Make LEDs independent of power-state */
- request_region(0x24, 4, "led_reg");
- reg = led_reg_read();
- reg |= 1 << 10;
- led_reg_write(reg);
-
- return 0;
-}
-
-/*
- * Since we may have triggers on any subsystem, defer registration
- * until after subsystem_init.
- */
-fs_initcall(shark_leds_init);
-#endif
+++ /dev/null
-/*
- * linux/arch/arm/mach-shark/pci.c
- *
- * PCI bios-type initialisation for PCI machines
- *
- * Bits taken from various places.
- */
-#include <linux/kernel.h>
-#include <linux/pci.h>
-#include <linux/init.h>
-#include <linux/io.h>
-#include <video/vga.h>
-
-#include <asm/irq.h>
-#include <asm/mach/pci.h>
-#include <asm/mach-types.h>
-
-#define IO_START 0x40000000
-
-static int __init shark_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
-{
- if (dev->bus->number == 0)
- if (dev->devfn == 0)
- return 255;
- else
- return 11;
- else
- return 255;
-}
-
-extern void __init via82c505_preinit(void);
-
-static struct hw_pci shark_pci __initdata = {
- .setup = via82c505_setup,
- .map_irq = shark_map_irq,
- .nr_controllers = 1,
- .ops = &via82c505_ops,
- .preinit = via82c505_preinit,
-};
-
-static int __init shark_pci_init(void)
-{
- if (!machine_is_shark())
- return -ENODEV;
-
- pcibios_min_io = 0x6000;
- pcibios_min_mem = 0x50000000;
- vga_base = 0xe8000000;
-
- pci_ioremap_io(0, IO_START);
-
- pci_common_init(&shark_pci);
-
- return 0;
-}
-
-subsys_initcall(shark_pci_init);
select RENESAS_INTC_IRQPIN
select REGULATOR_FIXED_VOLTAGE if REGULATOR
select USE_OF
+ select SND_SOC_AK4554 if SND_SIMPLE_CARD
+ select SND_SOC_AK4642 if SND_SIMPLE_CARD
config MACH_BOCKW_REFERENCE
bool "BOCK-W - Reference Device Tree Implementation"
This is intended to aid developers
+config MACH_KOELSCH
+ bool "Koelsch board"
+ depends on ARCH_R8A7791
+ select USE_OF
+
config MACH_KZM9D
bool "KZM9D board"
depends on ARCH_EMEV2
obj-$(CONFIG_MACH_LAGER_REFERENCE) += board-lager-reference.o
obj-$(CONFIG_MACH_ARMADILLO800EVA) += board-armadillo800eva.o
obj-$(CONFIG_MACH_ARMADILLO800EVA_REFERENCE) += board-armadillo800eva-reference.o
+obj-$(CONFIG_MACH_KOELSCH) += board-koelsch.o
obj-$(CONFIG_MACH_KZM9D) += board-kzm9d.o
obj-$(CONFIG_MACH_KZM9D_REFERENCE) += board-kzm9d-reference.o
obj-$(CONFIG_MACH_KZM9G) += board-kzm9g.o
loadaddr-$(CONFIG_MACH_ARMADILLO800EVA_REFERENCE) += 0x40008000
loadaddr-$(CONFIG_MACH_BOCKW) += 0x60008000
loadaddr-$(CONFIG_MACH_BOCKW_REFERENCE) += 0x60008000
+loadaddr-$(CONFIG_MACH_KOELSCH) += 0x40008000
loadaddr-$(CONFIG_MACH_KZM9D) += 0x40008000
loadaddr-$(CONFIG_MACH_KZM9D_REFERENCE) += 0x40008000
loadaddr-$(CONFIG_MACH_KZM9G) += 0x41008000
GPIO_KEY(KEY_VOLUMEDOWN, 329, "S21"),
};
-static struct __initdata gpio_keys_platform_data ape6evm_keys_pdata = {
+static struct gpio_keys_platform_data ape6evm_keys_pdata __initdata = {
.buttons = gpio_buttons,
.nbuttons = ARRAY_SIZE(gpio_buttons),
};
};
/*
- * On APE6EVM power is supplied to MMCIF by a tps80032 regulator. For now we
- * model a VDD supply to MMCIF, using a fixed 3.3V regulator. Also use the
- * static power supply for SDHI0 and SDHI1, whereas SDHI0's VccQ is also
- * supplied by the same tps80032 regulator and thus can also be adjusted
- * dynamically.
+ * MMC0 power supplies:
+ * Both Vcc and VccQ to eMMC on APE6EVM are supplied by a tps80032 voltage
+ * regulator. Until support for it is added to this file we simulate the
+ * Vcc supply by a fixed always-on regulator
*/
-static struct regulator_consumer_supply fixed3v3_power_consumers[] =
+static struct regulator_consumer_supply vcc_mmc0_consumers[] =
{
REGULATOR_SUPPLY("vmmc", "sh_mmcif.0"),
+};
+
+/*
+ * SDHI0 power supplies:
+ * Vcc to SDHI0 on APE6EVM is supplied by a GPIO-switchable regulator. VccQ is
+ * provided by the same tps80032 regulator as both MMC0 voltages - see comment
+ * above
+ */
+static struct regulator_consumer_supply vcc_sdhi0_consumers[] =
+{
REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"),
+};
+
+static struct regulator_init_data vcc_sdhi0_init_data = {
+ .constraints = {
+ .valid_ops_mask = REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(vcc_sdhi0_consumers),
+ .consumer_supplies = vcc_sdhi0_consumers,
+};
+
+static const struct fixed_voltage_config vcc_sdhi0_info __initconst = {
+ .supply_name = "SDHI0 Vcc",
+ .microvolts = 3300000,
+ .gpio = 76,
+ .enable_high = 1,
+ .init_data = &vcc_sdhi0_init_data,
+};
+
+/*
+ * SDHI1 power supplies:
+ * Vcc and VccQ to SDHI1 on APE6EVM are both fixed at 3.3V
+ */
+static struct regulator_consumer_supply vcc_sdhi1_consumers[] =
+{
REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.1"),
};
/* MMCIF */
static const struct sh_mmcif_plat_data mmcif0_pdata __initconst = {
.caps = MMC_CAP_8_BIT_DATA | MMC_CAP_NONREMOVABLE,
+ .ccs_unsupported = true,
};
static const struct resource mmcif0_resources[] __initconst = {
platform_device_register_resndata(&platform_bus, "smsc911x", -1,
lan9220_res, ARRAY_SIZE(lan9220_res),
&lan9220_data, sizeof(lan9220_data));
- regulator_register_always_on(1, "fixed-3.3V", fixed3v3_power_consumers,
- ARRAY_SIZE(fixed3v3_power_consumers), 3300000);
+
+ regulator_register_always_on(1, "MMC0 Vcc", vcc_mmc0_consumers,
+ ARRAY_SIZE(vcc_mmc0_consumers), 2800000);
platform_device_register_resndata(&platform_bus, "sh_mmcif", 0,
mmcif0_resources, ARRAY_SIZE(mmcif0_resources),
&mmcif0_pdata, sizeof(mmcif0_pdata));
+ platform_device_register_data(&platform_bus, "reg-fixed-voltage", 2,
+ &vcc_sdhi0_info, sizeof(vcc_sdhi0_info));
platform_device_register_resndata(&platform_bus, "sh_mobile_sdhi", 0,
sdhi0_resources, ARRAY_SIZE(sdhi0_resources),
&sdhi0_pdata, sizeof(sdhi0_pdata));
+ regulator_register_always_on(3, "SDHI1 Vcc", vcc_sdhi1_consumers,
+ ARRAY_SIZE(vcc_sdhi1_consumers), 3300000);
platform_device_register_resndata(&platform_bus, "sh_mobile_sdhi", 1,
sdhi1_resources, ARRAY_SIZE(sdhi1_resources),
&sdhi1_pdata, sizeof(sdhi1_pdata));
.caps = MMC_CAP_4_BIT_DATA |
MMC_CAP_8_BIT_DATA |
MMC_CAP_NONREMOVABLE,
+ .ccs_unsupported = true,
.slave_id_tx = SHDMA_SLAVE_MMCIF_TX,
.slave_id_rx = SHDMA_SLAVE_MMCIF_RX,
};
#include <linux/smsc911x.h>
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
+#include <linux/usb/renesas_usbhs.h>
#include <media/soc_camera.h>
#include <mach/common.h>
#include <mach/irqs.h>
#include <mach/r8a7778.h>
#include <asm/mach/arch.h>
+#include <sound/rcar_snd.h>
+#include <sound/simple_card.h>
+
+#define FPGA 0x18200000
+#define IRQ0MR 0x30
+#define COMCTLR 0x101c
+static void __iomem *fpga;
/*
* CN9(Upper side) SCIF/RCAN selection
* SW19 (MMC) 1 pin
*/
+/*
+ * SSI settings
+ *
+ * SW45: 1-4 side (SSI5 out, ROUT/LOUT CN19 Mid)
+ * SW46: 1101 (SSI6 Recorde)
+ * SW47: 1110 (SSI5 Playback)
+ * SW48: 11 (Recorde power)
+ * SW49: 1 (SSI slave mode)
+ * SW50: 1111 (SSI7, SSI8)
+ * SW51: 1111 (SSI3, SSI4)
+ * SW54: 1pin (ak4554 FPGA control)
+ * SW55: 1 (CLKB is 24.5760MHz)
+ * SW60: 1pin (ak4554 FPGA control)
+ * SW61: 3pin (use X11 clock)
+ * SW78: 3-6 (ak4642 connects I2C0)
+ *
+ * You can use sound as
+ *
+ * hw0: CN19: SSI56-AK4643
+ * hw1: CN21: SSI3-AK4554(playback)
+ * hw2: CN21: SSI4-AK4554(capture)
+ * hw3: CN20: SSI7-AK4554(playback)
+ * hw4: CN20: SSI8-AK4554(capture)
+ *
+ * this command is required when playback on hw0.
+ *
+ * # amixer set "LINEOUT Mixer DACL" on
+ */
+
+/*
+ * USB
+ *
+ * USB1 (CN29) can be Host/Function
+ *
+ * Host Func
+ * SW98 1 2
+ * SW99 1 3
+ */
+
/* Dummy supplies, where voltage doesn't matter */
static struct regulator_consumer_supply dummy_supplies[] = {
REGULATOR_SUPPLY("vddvario", "smsc911x"),
DEFINE_RES_IRQ(irq_pin(0)), /* IRQ 0 */
};
+#if IS_ENABLED(CONFIG_USB_RENESAS_USBHS_UDC)
+/*
+ * When USB1 is Func
+ */
+static int usbhsf_get_id(struct platform_device *pdev)
+{
+ return USBHS_GADGET;
+}
+
+#define SUSPMODE 0x102
+static int usbhsf_power_ctrl(struct platform_device *pdev,
+ void __iomem *base, int enable)
+{
+ enable = !!enable;
+
+ r8a7778_usb_phy_power(enable);
+
+ iowrite16(enable << 14, base + SUSPMODE);
+
+ return 0;
+}
+
+static struct resource usbhsf_resources[] __initdata = {
+ DEFINE_RES_MEM(0xffe60000, 0x110),
+ DEFINE_RES_IRQ(gic_iid(0x4f)),
+};
+
+static struct renesas_usbhs_platform_info usbhs_info __initdata = {
+ .platform_callback = {
+ .get_id = usbhsf_get_id,
+ .power_ctrl = usbhsf_power_ctrl,
+ },
+ .driver_param = {
+ .buswait_bwait = 4,
+ },
+};
+
+#define USB_PHY_SETTING {.port1_func = 1, .ovc_pin[1].active_high = 1,}
+#define USB1_DEVICE "renesas_usbhs"
+#define ADD_USB_FUNC_DEVICE_IF_POSSIBLE() \
+ platform_device_register_resndata( \
+ &platform_bus, "renesas_usbhs", -1, \
+ usbhsf_resources, \
+ ARRAY_SIZE(usbhsf_resources), \
+ &usbhs_info, sizeof(struct renesas_usbhs_platform_info))
+
+#else
+/*
+ * When USB1 is Host
+ */
+#define USB_PHY_SETTING { }
+#define USB1_DEVICE "ehci-platform"
+#define ADD_USB_FUNC_DEVICE_IF_POSSIBLE()
+
+#endif
+
/* USB */
static struct resource usb_phy_resources[] __initdata = {
DEFINE_RES_MEM(0xffe70800, 0x100),
DEFINE_RES_MEM(0xffe76000, 0x100),
};
-static struct rcar_phy_platform_data usb_phy_platform_data __initdata;
+static struct rcar_phy_platform_data usb_phy_platform_data __initdata =
+ USB_PHY_SETTING;
+
/* SDHI */
static struct sh_mobile_sdhi_info sdhi0_info __initdata = {
DEFINE_RES_IRQ(gic_iid(0x77)),
};
+/* Ether */
+static struct resource ether_resources[] __initdata = {
+ DEFINE_RES_MEM(0xfde00000, 0x400),
+ DEFINE_RES_IRQ(gic_iid(0x89)),
+};
+
static struct sh_eth_plat_data ether_platform_data __initdata = {
.phy = 0x01,
.edmac_endian = EDMAC_LITTLE_ENDIAN,
static struct i2c_board_info i2c0_devices[] = {
{
I2C_BOARD_INFO("rx8581", 0x51),
- },
+ }, {
+ I2C_BOARD_INFO("ak4643", 0x12),
+ }
};
/* HSPI*/
MMC_CAP_NEEDS_POLL,
};
-static struct rcar_vin_platform_data vin_platform_data __initdata = {
- .flags = RCAR_VIN_BT656,
-};
-
/* In the default configuration both decoders reside on I2C bus 0 */
#define BOCKW_CAMERA(idx) \
static struct i2c_board_info camera##idx##_info = { \
BOCKW_CAMERA(0);
BOCKW_CAMERA(1);
+/* Sound */
+static struct resource rsnd_resources[] __initdata = {
+ [RSND_GEN1_SRU] = DEFINE_RES_MEM(0xffd90000, 0x1000),
+ [RSND_GEN1_SSI] = DEFINE_RES_MEM(0xffd91000, 0x1240),
+ [RSND_GEN1_ADG] = DEFINE_RES_MEM(0xfffe0000, 0x24),
+};
+
+static struct rsnd_ssi_platform_info rsnd_ssi[] = {
+ RSND_SSI_UNUSED, /* SSI 0 */
+ RSND_SSI_UNUSED, /* SSI 1 */
+ RSND_SSI_UNUSED, /* SSI 2 */
+ RSND_SSI_SET(1, 0, gic_iid(0x85), RSND_SSI_PLAY),
+ RSND_SSI_SET(2, 0, gic_iid(0x85), RSND_SSI_CLK_PIN_SHARE | RSND_SSI_CLK_FROM_ADG),
+ RSND_SSI_SET(0, 0, gic_iid(0x86), RSND_SSI_PLAY),
+ RSND_SSI_SET(0, 0, gic_iid(0x86), 0),
+ RSND_SSI_SET(3, 0, gic_iid(0x86), RSND_SSI_PLAY),
+ RSND_SSI_SET(4, 0, gic_iid(0x86), RSND_SSI_CLK_PIN_SHARE | RSND_SSI_CLK_FROM_ADG),
+};
+
+static struct rsnd_scu_platform_info rsnd_scu[9] = {
+ /* no member at this point */
+};
+
+enum {
+ AK4554_34 = 0,
+ AK4643_56,
+ AK4554_78,
+ SOUND_MAX,
+};
+
+static int rsnd_codec_power(int id, int enable)
+{
+ static int sound_user[SOUND_MAX] = {0, 0, 0};
+ int *usr = NULL;
+ u32 bit;
+
+ switch (id) {
+ case 3:
+ case 4:
+ usr = sound_user + AK4554_34;
+ bit = (1 << 10);
+ break;
+ case 5:
+ case 6:
+ usr = sound_user + AK4643_56;
+ bit = (1 << 6);
+ break;
+ case 7:
+ case 8:
+ usr = sound_user + AK4554_78;
+ bit = (1 << 7);
+ break;
+ }
+
+ if (!usr)
+ return -EIO;
+
+ if (enable) {
+ if (*usr == 0) {
+ u32 val = ioread16(fpga + COMCTLR);
+ val &= ~bit;
+ iowrite16(val, fpga + COMCTLR);
+ }
+
+ (*usr)++;
+ } else {
+ if (*usr == 0)
+ return 0;
+
+ (*usr)--;
+
+ if (*usr == 0) {
+ u32 val = ioread16(fpga + COMCTLR);
+ val |= bit;
+ iowrite16(val, fpga + COMCTLR);
+ }
+ }
+
+ return 0;
+}
+
+static int rsnd_start(int id)
+{
+ return rsnd_codec_power(id, 1);
+}
+
+static int rsnd_stop(int id)
+{
+ return rsnd_codec_power(id, 0);
+}
+
+static struct rcar_snd_info rsnd_info = {
+ .flags = RSND_GEN1,
+ .ssi_info = rsnd_ssi,
+ .ssi_info_nr = ARRAY_SIZE(rsnd_ssi),
+ .scu_info = rsnd_scu,
+ .scu_info_nr = ARRAY_SIZE(rsnd_scu),
+ .start = rsnd_start,
+ .stop = rsnd_stop,
+};
+
+static struct asoc_simple_card_info rsnd_card_info[] = {
+ /* SSI5, SSI6 */
+ {
+ .name = "AK4643",
+ .card = "SSI56-AK4643",
+ .codec = "ak4642-codec.0-0012",
+ .platform = "rcar_sound",
+ .daifmt = SND_SOC_DAIFMT_LEFT_J,
+ .cpu_dai = {
+ .name = "rsnd-dai.0",
+ .fmt = SND_SOC_DAIFMT_CBS_CFS,
+ },
+ .codec_dai = {
+ .name = "ak4642-hifi",
+ .fmt = SND_SOC_DAIFMT_CBM_CFM,
+ .sysclk = 11289600,
+ },
+ },
+ /* SSI3 */
+ {
+ .name = "AK4554",
+ .card = "SSI3-AK4554(playback)",
+ .codec = "ak4554-adc-dac.0",
+ .platform = "rcar_sound",
+ .cpu_dai = {
+ .name = "rsnd-dai.1",
+ .fmt = SND_SOC_DAIFMT_CBM_CFM |
+ SND_SOC_DAIFMT_RIGHT_J,
+ },
+ .codec_dai = {
+ .name = "ak4554-hifi",
+ },
+ },
+ /* SSI4 */
+ {
+ .name = "AK4554",
+ .card = "SSI4-AK4554(capture)",
+ .codec = "ak4554-adc-dac.0",
+ .platform = "rcar_sound",
+ .cpu_dai = {
+ .name = "rsnd-dai.2",
+ .fmt = SND_SOC_DAIFMT_CBM_CFM |
+ SND_SOC_DAIFMT_LEFT_J,
+ },
+ .codec_dai = {
+ .name = "ak4554-hifi",
+ },
+ },
+ /* SSI7 */
+ {
+ .name = "AK4554",
+ .card = "SSI7-AK4554(playback)",
+ .codec = "ak4554-adc-dac.1",
+ .platform = "rcar_sound",
+ .cpu_dai = {
+ .name = "rsnd-dai.3",
+ .fmt = SND_SOC_DAIFMT_CBM_CFM |
+ SND_SOC_DAIFMT_RIGHT_J,
+ },
+ .codec_dai = {
+ .name = "ak4554-hifi",
+ },
+ },
+ /* SSI8 */
+ {
+ .name = "AK4554",
+ .card = "SSI8-AK4554(capture)",
+ .codec = "ak4554-adc-dac.1",
+ .platform = "rcar_sound",
+ .cpu_dai = {
+ .name = "rsnd-dai.4",
+ .fmt = SND_SOC_DAIFMT_CBM_CFM |
+ SND_SOC_DAIFMT_LEFT_J,
+ },
+ .codec_dai = {
+ .name = "ak4554-hifi",
+ },
+ }
+};
+
+/* VIN */
+static struct rcar_vin_platform_data vin_platform_data __initdata = {
+ .flags = RCAR_VIN_BT656,
+};
+
+#define R8A7778_VIN(idx) \
+static struct resource vin##idx##_resources[] __initdata = { \
+ DEFINE_RES_MEM(0xffc50000 + 0x1000 * (idx), 0x1000), \
+ DEFINE_RES_IRQ(gic_iid(0x5a)), \
+}; \
+ \
+static struct platform_device_info vin##idx##_info __initdata = { \
+ .parent = &platform_bus, \
+ .name = "r8a7778-vin", \
+ .id = idx, \
+ .res = vin##idx##_resources, \
+ .num_res = ARRAY_SIZE(vin##idx##_resources), \
+ .dma_mask = DMA_BIT_MASK(32), \
+ .data = &vin_platform_data, \
+ .size_data = sizeof(vin_platform_data), \
+}
+R8A7778_VIN(0);
+R8A7778_VIN(1);
+
static const struct pinctrl_map bockw_pinctrl_map[] = {
+ /* AUDIO */
+ PIN_MAP_MUX_GROUP_DEFAULT("rcar_sound", "pfc-r8a7778",
+ "audio_clk_a", "audio_clk"),
+ PIN_MAP_MUX_GROUP_DEFAULT("rcar_sound", "pfc-r8a7778",
+ "audio_clk_b", "audio_clk"),
+ PIN_MAP_MUX_GROUP_DEFAULT("rcar_sound", "pfc-r8a7778",
+ "ssi34_ctrl", "ssi"),
+ PIN_MAP_MUX_GROUP_DEFAULT("rcar_sound", "pfc-r8a7778",
+ "ssi3_data", "ssi"),
+ PIN_MAP_MUX_GROUP_DEFAULT("rcar_sound", "pfc-r8a7778",
+ "ssi4_data", "ssi"),
+ PIN_MAP_MUX_GROUP_DEFAULT("rcar_sound", "pfc-r8a7778",
+ "ssi5_ctrl", "ssi"),
+ PIN_MAP_MUX_GROUP_DEFAULT("rcar_sound", "pfc-r8a7778",
+ "ssi5_data", "ssi"),
+ PIN_MAP_MUX_GROUP_DEFAULT("rcar_sound", "pfc-r8a7778",
+ "ssi6_ctrl", "ssi"),
+ PIN_MAP_MUX_GROUP_DEFAULT("rcar_sound", "pfc-r8a7778",
+ "ssi6_data", "ssi"),
+ PIN_MAP_MUX_GROUP_DEFAULT("rcar_sound", "pfc-r8a7778",
+ "ssi78_ctrl", "ssi"),
+ PIN_MAP_MUX_GROUP_DEFAULT("rcar_sound", "pfc-r8a7778",
+ "ssi7_data", "ssi"),
+ PIN_MAP_MUX_GROUP_DEFAULT("rcar_sound", "pfc-r8a7778",
+ "ssi8_data", "ssi"),
/* Ether */
PIN_MAP_MUX_GROUP_DEFAULT("r8a777x-ether", "pfc-r8a7778",
"ether_rmii", "ether"),
/* USB */
PIN_MAP_MUX_GROUP_DEFAULT("ehci-platform", "pfc-r8a7778",
"usb0", "usb0"),
- PIN_MAP_MUX_GROUP_DEFAULT("ehci-platform", "pfc-r8a7778",
+ PIN_MAP_MUX_GROUP_DEFAULT(USB1_DEVICE, "pfc-r8a7778",
"usb1", "usb1"),
/* SDHI0 */
PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-r8a7778",
"vin1_data8", "vin1"),
};
-#define FPGA 0x18200000
-#define IRQ0MR 0x30
#define PFC 0xfffc0000
#define PUPR4 0x110
static void __init bockw_init(void)
{
void __iomem *base;
+ struct clk *clk;
+ int i;
r8a7778_clock_init();
r8a7778_init_irq_extpin(1);
r8a7778_add_standard_devices();
- r8a7778_add_ether_device(ðer_platform_data);
- r8a7778_add_vin_device(0, &vin_platform_data);
+
+ platform_device_register_resndata(&platform_bus, "r8a777x-ether", -1,
+ ether_resources,
+ ARRAY_SIZE(ether_resources),
+ ðer_platform_data,
+ sizeof(ether_platform_data));
+
+ platform_device_register_full(&vin0_info);
/* VIN1 has a pin conflict with Ether */
if (!IS_ENABLED(CONFIG_SH_ETH))
- r8a7778_add_vin_device(1, &vin_platform_data);
+ platform_device_register_full(&vin1_info);
platform_device_register_data(&platform_bus, "soc-camera-pdrv", 0,
&iclink0_ml86v7667,
sizeof(iclink0_ml86v7667));
/* for SMSC */
- base = ioremap_nocache(FPGA, SZ_1M);
- if (base) {
+ fpga = ioremap_nocache(FPGA, SZ_1M);
+ if (fpga) {
/*
* CAUTION
*
* it should be cared in the future
* Now, it is assuming IRQ0 was used only from SMSC.
*/
- u16 val = ioread16(base + IRQ0MR);
+ u16 val = ioread16(fpga + IRQ0MR);
val &= ~(1 << 4); /* enable SMSC911x */
- iowrite16(val, base + IRQ0MR);
- iounmap(base);
+ iowrite16(val, fpga + IRQ0MR);
regulator_register_fixed(0, dummy_supplies,
ARRAY_SIZE(dummy_supplies));
sdhi0_resources, ARRAY_SIZE(sdhi0_resources),
&sdhi0_info, sizeof(struct sh_mobile_sdhi_info));
}
+
+ /* for Audio */
+ clk = clk_get(NULL, "audio_clk_b");
+ clk_set_rate(clk, 24576000);
+ clk_put(clk);
+ rsnd_codec_power(5, 1); /* enable ak4642 */
+
+ platform_device_register_simple(
+ "ak4554-adc-dac", 0, NULL, 0);
+
+ platform_device_register_simple(
+ "ak4554-adc-dac", 1, NULL, 0);
+
+ platform_device_register_resndata(
+ &platform_bus, "rcar_sound", -1,
+ rsnd_resources, ARRAY_SIZE(rsnd_resources),
+ &rsnd_info, sizeof(rsnd_info));
+
+ for (i = 0; i < ARRAY_SIZE(rsnd_card_info); i++) {
+ struct platform_device_info cardinfo = {
+ .parent = &platform_bus,
+ .name = "asoc-simple-card",
+ .id = i,
+ .data = &rsnd_card_info[i],
+ .size_data = sizeof(struct asoc_simple_card_info),
+ .dma_mask = ~0,
+ };
+
+ platform_device_register_full(&cardinfo);
+ }
+}
+
+static void __init bockw_init_late(void)
+{
+ r8a7778_init_late();
+ ADD_USB_FUNC_DEVICE_IF_POSSIBLE();
}
static const char *bockw_boards_compat_dt[] __initdata = {
.init_irq = r8a7778_init_irq_dt,
.init_machine = bockw_init,
.dt_compat = bockw_boards_compat_dt,
- .init_late = r8a7778_init_late,
+ .init_late = bockw_init_late,
MACHINE_END
--- /dev/null
+/*
+ * Koelsch board support
+ *
+ * Copyright (C) 2013 Renesas Electronics Corporation
+ * Copyright (C) 2013 Renesas Solutions Corp.
+ * Copyright (C) 2013 Magnus Damm
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <mach/common.h>
+#include <mach/r8a7791.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+
+static void __init koelsch_add_standard_devices(void)
+{
+ r8a7791_clock_init();
+ r8a7791_add_dt_devices();
+}
+
+static const char * const koelsch_boards_compat_dt[] __initconst = {
+ "renesas,koelsch",
+ NULL,
+};
+
+DT_MACHINE_START(KOELSCH_DT, "koelsch")
+ .init_early = r8a7791_init_early,
+ .init_machine = koelsch_add_standard_devices,
+ .dt_compat = koelsch_boards_compat_dt,
+MACHINE_END
static struct sh_mmcif_plat_data sh_mmcif_platdata = {
.ocr = MMC_VDD_165_195,
.caps = MMC_CAP_8_BIT_DATA | MMC_CAP_NONREMOVABLE,
+ .ccs_unsupported = true,
.slave_id_tx = SHDMA_SLAVE_MMCIF_TX,
.slave_id_rx = SHDMA_SLAVE_MMCIF_RX,
};
#include <linux/mmc/sh_mmcif.h>
#include <linux/pinctrl/machine.h>
#include <linux/platform_data/gpio-rcar.h>
+#include <linux/platform_data/rcar-du.h>
#include <linux/platform_device.h>
#include <linux/phy.h>
#include <linux/regulator/fixed.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
+/* DU */
+static struct rcar_du_encoder_data lager_du_encoders[] = {
+ {
+ .type = RCAR_DU_ENCODER_VGA,
+ .output = RCAR_DU_OUTPUT_DPAD0,
+ }, {
+ .type = RCAR_DU_ENCODER_NONE,
+ .output = RCAR_DU_OUTPUT_LVDS1,
+ .connector.lvds.panel = {
+ .width_mm = 210,
+ .height_mm = 158,
+ .mode = {
+ .clock = 65000,
+ .hdisplay = 1024,
+ .hsync_start = 1048,
+ .hsync_end = 1184,
+ .htotal = 1344,
+ .vdisplay = 768,
+ .vsync_start = 771,
+ .vsync_end = 777,
+ .vtotal = 806,
+ .flags = 0,
+ },
+ },
+ },
+};
+
+static const struct rcar_du_platform_data lager_du_pdata __initconst = {
+ .encoders = lager_du_encoders,
+ .num_encoders = ARRAY_SIZE(lager_du_encoders),
+};
+
+static const struct resource du_resources[] __initconst = {
+ DEFINE_RES_MEM(0xfeb00000, 0x70000),
+ DEFINE_RES_MEM_NAMED(0xfeb90000, 0x1c, "lvds.0"),
+ DEFINE_RES_MEM_NAMED(0xfeb94000, 0x1c, "lvds.1"),
+ DEFINE_RES_IRQ(gic_spi(256)),
+ DEFINE_RES_IRQ(gic_spi(268)),
+ DEFINE_RES_IRQ(gic_spi(269)),
+};
+
+static void __init lager_add_du_device(void)
+{
+ struct platform_device_info info = {
+ .name = "rcar-du-r8a7790",
+ .id = -1,
+ .res = du_resources,
+ .num_res = ARRAY_SIZE(du_resources),
+ .data = &lager_du_pdata,
+ .size_data = sizeof(lager_du_pdata),
+ .dma_mask = DMA_BIT_MASK(32),
+ };
+
+ platform_device_register_full(&info);
+}
+
/* LEDS */
static struct gpio_led lager_leds[] = {
{
},
};
-static __initdata struct gpio_led_platform_data lager_leds_pdata = {
+static const struct gpio_led_platform_data lager_leds_pdata __initconst = {
.leds = lager_leds,
.num_leds = ARRAY_SIZE(lager_leds),
};
GPIO_KEY(KEY_1, RCAR_GP_PIN(1, 14), "SW2-pin1"),
};
-static __initdata struct gpio_keys_platform_data lager_keys_pdata = {
+static const struct gpio_keys_platform_data lager_keys_pdata __initconst = {
.buttons = gpio_buttons,
.nbuttons = ARRAY_SIZE(gpio_buttons),
};
};
/* MMCIF */
-static struct sh_mmcif_plat_data mmcif1_pdata __initdata = {
+static const struct sh_mmcif_plat_data mmcif1_pdata __initconst = {
.caps = MMC_CAP_8_BIT_DATA | MMC_CAP_NONREMOVABLE,
+ .clk_ctrl2_present = true,
+ .ccs_unsupported = true,
};
-static struct resource mmcif1_resources[] __initdata = {
+static const struct resource mmcif1_resources[] __initconst = {
DEFINE_RES_MEM_NAMED(0xee220000, 0x80, "MMCIF1"),
DEFINE_RES_IRQ(gic_spi(170)),
};
/* Ether */
-static struct sh_eth_plat_data ether_pdata __initdata = {
+static const struct sh_eth_plat_data ether_pdata __initconst = {
.phy = 0x1,
.edmac_endian = EDMAC_LITTLE_ENDIAN,
.phy_interface = PHY_INTERFACE_MODE_RMII,
.ether_link_active_low = 1,
};
-static struct resource ether_resources[] __initdata = {
+static const struct resource ether_resources[] __initconst = {
DEFINE_RES_MEM(0xee700000, 0x400),
DEFINE_RES_IRQ(gic_spi(162)),
};
static const struct pinctrl_map lager_pinctrl_map[] = {
+ /* DU (CN10: ARGB0, CN13: LVDS) */
+ PIN_MAP_MUX_GROUP_DEFAULT("rcar-du-r8a7790", "pfc-r8a7790",
+ "du_rgb666", "du"),
+ PIN_MAP_MUX_GROUP_DEFAULT("rcar-du-r8a7790", "pfc-r8a7790",
+ "du_sync_1", "du"),
+ PIN_MAP_MUX_GROUP_DEFAULT("rcar-du-r8a7790", "pfc-r8a7790",
+ "du_clk_out_0", "du"),
/* SCIF0 (CN19: DEBUG SERIAL0) */
PIN_MAP_MUX_GROUP_DEFAULT("sh-sci.6", "pfc-r8a7790",
"scif0_data", "scif0"),
ether_resources,
ARRAY_SIZE(ether_resources),
ðer_pdata, sizeof(ether_pdata));
+
+ lager_add_du_device();
}
/*
phy_register_fixup_for_id("r8a7790-ether-ff:01", lager_ksz8041_fixup);
}
-static const char *lager_boards_compat_dt[] __initdata = {
+static const char * const lager_boards_compat_dt[] __initconst = {
"renesas,lager",
NULL,
};
#include <linux/dma-mapping.h>
#include <linux/pinctrl/machine.h>
#include <linux/platform_data/gpio-rcar.h>
+#include <linux/platform_data/rcar-du.h>
#include <linux/platform_data/usb-rcar-phy.h>
#include <linux/regulator/fixed.h>
#include <linux/regulator/machine.h>
.num_resources = ARRAY_SIZE(hspi_resources),
};
+/*
+ * DU
+ *
+ * The panel only specifies the [hv]display and [hv]total values. The position
+ * and width of the sync pulses don't matter, they're copied from VESA timings.
+ */
+static struct rcar_du_encoder_data du_encoders[] = {
+ {
+ .type = RCAR_DU_ENCODER_VGA,
+ .output = RCAR_DU_OUTPUT_DPAD0,
+ }, {
+ .type = RCAR_DU_ENCODER_LVDS,
+ .output = RCAR_DU_OUTPUT_DPAD1,
+ .connector.lvds.panel = {
+ .width_mm = 210,
+ .height_mm = 158,
+ .mode = {
+ .clock = 65000,
+ .hdisplay = 1024,
+ .hsync_start = 1048,
+ .hsync_end = 1184,
+ .htotal = 1344,
+ .vdisplay = 768,
+ .vsync_start = 771,
+ .vsync_end = 777,
+ .vtotal = 806,
+ .flags = 0,
+ },
+ },
+ },
+};
+
+static const struct rcar_du_platform_data du_pdata __initconst = {
+ .encoders = du_encoders,
+ .num_encoders = ARRAY_SIZE(du_encoders),
+};
+
+static const struct resource du_resources[] __initconst = {
+ DEFINE_RES_MEM(0xfff80000, 0x40000),
+ DEFINE_RES_IRQ(gic_iid(0x3f)),
+};
+
+static void __init marzen_add_du_device(void)
+{
+ struct platform_device_info info = {
+ .name = "rcar-du-r8a7779",
+ .id = -1,
+ .res = du_resources,
+ .num_res = ARRAY_SIZE(du_resources),
+ .data = &du_pdata,
+ .size_data = sizeof(du_pdata),
+ .dma_mask = DMA_BIT_MASK(32),
+ };
+
+ platform_device_register_full(&info);
+}
+
/* LEDS */
static struct gpio_led marzen_leds[] = {
{
};
static const struct pinctrl_map marzen_pinctrl_map[] = {
+ /* DU (CN10: ARGB0, CN13: LVDS) */
+ PIN_MAP_MUX_GROUP_DEFAULT("rcar-du-r8a7779", "pfc-r8a7779",
+ "du0_rgb888", "du0"),
+ PIN_MAP_MUX_GROUP_DEFAULT("rcar-du-r8a7779", "pfc-r8a7779",
+ "du0_sync_1", "du0"),
+ PIN_MAP_MUX_GROUP_DEFAULT("rcar-du-r8a7779", "pfc-r8a7779",
+ "du0_clk_out_0", "du0"),
+ PIN_MAP_MUX_GROUP_DEFAULT("rcar-du-r8a7779", "pfc-r8a7779",
+ "du1_rgb666", "du1"),
+ PIN_MAP_MUX_GROUP_DEFAULT("rcar-du-r8a7779", "pfc-r8a7779",
+ "du1_sync_1", "du1"),
+ PIN_MAP_MUX_GROUP_DEFAULT("rcar-du-r8a7779", "pfc-r8a7779",
+ "du1_clk_out", "du1"),
/* HSPI0 */
PIN_MAP_MUX_GROUP_DEFAULT("sh-hspi.0", "pfc-r8a7779",
"hspi0", "hspi0"),
r8a7779_add_vin_device(1, &vin_platform_data);
r8a7779_add_vin_device(3, &vin_platform_data);
platform_add_devices(marzen_devices, ARRAY_SIZE(marzen_devices));
+ marzen_add_du_device();
}
static const char *marzen_boards_compat_dt[] __initdata = {
extern void r8a7778_add_standard_devices(void);
extern void r8a7778_add_standard_devices_dt(void);
-extern void r8a7778_add_ether_device(struct sh_eth_plat_data *pdata);
-extern void r8a7778_add_vin_device(int id,
- struct rcar_vin_platform_data *pdata);
extern void r8a7778_add_dt_devices(void);
extern void r8a7778_init_late(void);
USB_PLATFORM_INFO(ehci);
USB_PLATFORM_INFO(ohci);
-/* Ether */
-static struct resource ether_resources[] __initdata = {
- DEFINE_RES_MEM(0xfde00000, 0x400),
- DEFINE_RES_IRQ(gic_iid(0x89)),
-};
-
-void __init r8a7778_add_ether_device(struct sh_eth_plat_data *pdata)
-{
- platform_device_register_resndata(&platform_bus, "r8a777x-ether", -1,
- ether_resources,
- ARRAY_SIZE(ether_resources),
- pdata, sizeof(*pdata));
-}
-
/* PFC/GPIO */
static struct resource pfc_resources[] __initdata = {
DEFINE_RES_MEM(0xfffc0000, 0x118),
DEFINE_RES_IRQ(gic_iid(0x75)),
};
-void __init r8a7778_register_hspi(int id)
+static void __init r8a7778_register_hspi(int id)
{
BUG_ON(id < 0 || id > 2);
hspi_resources + (2 * id), 2);
}
-/* VIN */
-#define R8A7778_VIN(idx) \
-static struct resource vin##idx##_resources[] __initdata = { \
- DEFINE_RES_MEM(0xffc50000 + 0x1000 * (idx), 0x1000), \
- DEFINE_RES_IRQ(gic_iid(0x5a)), \
-}; \
- \
-static struct platform_device_info vin##idx##_info __initdata = { \
- .parent = &platform_bus, \
- .name = "r8a7778-vin", \
- .id = idx, \
- .res = vin##idx##_resources, \
- .num_res = ARRAY_SIZE(vin##idx##_resources), \
- .dma_mask = DMA_BIT_MASK(32), \
-}
-
-R8A7778_VIN(0);
-R8A7778_VIN(1);
-
-static struct platform_device_info *vin_info_table[] __initdata = {
- &vin0_info,
- &vin1_info,
-};
-
-void __init r8a7778_add_vin_device(int id, struct rcar_vin_platform_data *pdata)
-{
- BUG_ON(id < 0 || id > 1);
-
- vin_info_table[id]->data = pdata;
- vin_info_table[id]->size_data = sizeof(*pdata);
-
- platform_device_register_full(vin_info_table[id]);
-}
-
void __init r8a7778_add_dt_devices(void)
{
int i;
select ARM_AMBA
select ARM_GIC
select CACHE_L2X0
- select CLKDEV_LOOKUP
select COMMON_CLK
select CPU_V7
select DW_APB_TIMER_OF
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
-#include <linux/clk-provider.h>
#include <linux/irqchip.h>
#include <linux/of_address.h>
#include <linux/of_irq.h>
{
l2x0_of_init(0, ~0UL);
of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
- of_clk_init(NULL);
socfpga_init_clocks();
}
default PLAT_SPEAR_SINGLE
select ARCH_REQUIRE_GPIOLIB
select ARM_AMBA
- select CLKDEV_LOOKUP
select CLKSRC_MMIO
select COMMON_CLK
select GENERIC_CLOCKEVENTS
- select HAVE_CLK
if PLAT_SPEAR
* published by the Free Software Foundation.
*/
-#include <linux/clk-provider.h>
-#include <linux/clocksource.h>
#include <linux/irq.h>
+#include <linux/of_platform.h>
#include <asm/hardware/cache-l2x0.h>
#include <asm/mach/arch.h>
l2x0_of_init(aux_ctrl, L2X0_AUX_CTRL_MASK);
}
-static void __init stih41x_timer_init(void)
+static void __init stih41x_machine_init(void)
{
- of_clk_init(NULL);
- clocksource_of_init();
stih41x_l2x0_init();
+ of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
}
static const char *stih41x_dt_match[] __initdata = {
};
DT_MACHINE_START(STM, "STiH415/416 SoC with Flattened Device Tree")
- .init_time = stih41x_timer_init,
+ .init_machine = stih41x_machine_init,
.smp = smp_ops(sti_smp_ops),
.dt_compat = stih41x_dt_match,
MACHINE_END
* warranty of any kind, whether express or implied.
*/
-#include <linux/clocksource.h>
#include <linux/delay.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/io.h>
#include <linux/reboot.h>
-#include <linux/clk/sunxi.h>
-
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/system_misc.h>
arm_pm_restart = of_id->data;
}
-static void __init sunxi_timer_init(void)
-{
- sunxi_init_clocks();
- clocksource_of_init();
-}
-
static void __init sunxi_dt_init(void)
{
sunxi_setup_restart();
DT_MACHINE_START(SUNXI_DT, "Allwinner A1X (Device Tree)")
.init_machine = sunxi_dt_init,
- .init_time = sunxi_timer_init,
.dt_compat = sunxi_board_dt_compat,
MACHINE_END
select ARCH_HAS_CPUFREQ
select ARCH_REQUIRE_GPIOLIB
select ARM_GIC
- select CLKDEV_LOOKUP
select CLKSRC_MMIO
select CLKSRC_OF
select COMMON_CLK
select GENERIC_CLOCKEVENTS
select HAVE_ARM_SCU if SMP
select HAVE_ARM_TWD if SMP
- select HAVE_CLK
select HAVE_SMP
select MIGHT_HAVE_CACHE_L2X0
select MIGHT_HAVE_PCI
#include <linux/delay.h>
#include <linux/reboot.h>
#include <linux/irqchip.h>
-#include <linux/clk-provider.h>
#include <asm/hardware/cache-l2x0.h>
#ifdef CONFIG_OF
void __init tegra_dt_init_irq(void)
{
- of_clk_init(NULL);
- tegra_pmc_init();
+ tegra_pmc_init_irq();
tegra_init_irq();
irqchip_init();
tegra_legacy_irq_syscore_init();
{ }
};
-static void __init tegra_pmc_parse_dt(void)
+void __init tegra_pmc_init_irq(void)
{
struct device_node *np;
- u32 prop;
- enum tegra_suspend_mode suspend_mode;
- u32 core_good_time[2] = {0, 0};
- u32 lp0_vec[2] = {0, 0};
+ u32 val;
np = of_find_matching_node(NULL, matches);
BUG_ON(!np);
tegra_pmc_invert_interrupt = of_property_read_bool(np,
"nvidia,invert-interrupt");
+
+ val = tegra_pmc_readl(PMC_CTRL);
+ if (tegra_pmc_invert_interrupt)
+ val |= PMC_CTRL_INTR_LOW;
+ else
+ val &= ~PMC_CTRL_INTR_LOW;
+ tegra_pmc_writel(val, PMC_CTRL);
+}
+
+void __init tegra_pmc_init(void)
+{
+ struct device_node *np;
+ u32 prop;
+ enum tegra_suspend_mode suspend_mode;
+ u32 core_good_time[2] = {0, 0};
+ u32 lp0_vec[2] = {0, 0};
+
+ np = of_find_matching_node(NULL, matches);
+ BUG_ON(!np);
+
tegra_pclk = of_clk_get_by_name(np, "pclk");
WARN_ON(IS_ERR(tegra_pclk));
pmc_pm_data.suspend_mode = suspend_mode;
}
-
-void __init tegra_pmc_init(void)
-{
- u32 val;
-
- tegra_pmc_parse_dt();
-
- val = tegra_pmc_readl(PMC_CTRL);
- if (tegra_pmc_invert_interrupt)
- val |= PMC_CTRL_INTR_LOW;
- else
- val &= ~PMC_CTRL_INTR_LOW;
- tegra_pmc_writel(val, PMC_CTRL);
-}
int tegra_pmc_cpu_power_on(int cpuid);
int tegra_pmc_cpu_remove_clamping(int cpuid);
+void tegra_pmc_init_irq(void);
void tegra_pmc_init(void);
#endif
*
*/
-#include <linux/clocksource.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include "common.h"
#include "fuse.h"
#include "iomap.h"
+#include "pmc.h"
static void __init tegra_dt_init(void)
{
struct soc_device *soc_dev;
struct device *parent = NULL;
+ tegra_pmc_init();
+
tegra_clocks_apply_init_table();
soc_dev_attr = kzalloc(sizeof(*soc_dev_attr), GFP_KERNEL);
.smp = smp_ops(tegra_smp_ops),
.init_early = tegra_init_early,
.init_irq = tegra_dt_init_irq,
- .init_time = clocksource_of_init,
.init_machine = tegra_dt_init,
.init_late = tegra_dt_init_late,
.restart = tegra_assert_system_reset,
select ARM_AMBA
select ARM_PATCH_PHYS_VIRT
select ARM_VIC
- select CLKDEV_LOOKUP
select CLKSRC_MMIO
select CLKSRC_OF
select COMMON_CLK
config ARCH_U8500
bool "ST-Ericsson U8500 Series" if ARCH_MULTI_V7
depends on MMU
+ select AB8500_CORE
+ select ABX500_CORE
select ARCH_HAS_CPUFREQ
select ARCH_REQUIRE_GPIOLIB
select ARM_AMBA
- select CLKDEV_LOOKUP
+ select ARM_ERRATA_754322
+ select ARM_ERRATA_764369 if SMP
+ select ARM_GIC
+ select CACHE_L2X0
+ select CLKSRC_NOMADIK_MTU
+ select COMMON_CLK
select CPU_V7
select GENERIC_CLOCKEVENTS
select HAVE_ARM_SCU if SMP
select HAVE_ARM_TWD if SMP
select HAVE_SMP
select MIGHT_HAVE_CACHE_L2X0
+ select PINCTRL
+ select PINCTRL_ABX500
+ select PINCTRL_NOMADIK
+ select PL310_ERRATA_753970 if CACHE_PL310
help
Support for ST-Ericsson's Ux500 architecture
if ARCH_U8500
-config UX500_SOC_COMMON
- bool
- default y
- select ABX500_CORE
- select AB8500_CORE
- select ARM_ERRATA_754322
- select ARM_ERRATA_764369 if SMP
- select ARM_GIC
- select CACHE_L2X0
- select CLKSRC_NOMADIK_MTU
- select COMMON_CLK
- select PINCTRL
- select PINCTRL_NOMADIK
- select PINCTRL_ABX500
- select PL310_ERRATA_753970 if CACHE_PL310
-
config UX500_SOC_DB8500
bool
select CPU_FREQ_TABLE if CPU_FREQ
# Makefile for the linux kernel, U8500 machine.
#
-obj-y := cpu.o devices.o devices-common.o \
- id.o usb.o timer.o pm.o
+obj-y := cpu.o devices.o id.o timer.o pm.o
obj-$(CONFIG_CACHE_L2X0) += cache-l2x0.o
obj-$(CONFIG_UX500_SOC_DB8500) += cpu-db8500.o devices-db8500.o
obj-$(CONFIG_MACH_MOP500) += board-mop500.o board-mop500-sdi.o \
board-mop500-regulators.o \
- board-mop500-uib.o board-mop500-stuib.o \
- board-mop500-u8500uib.o \
board-mop500-pins.o \
board-mop500-audio.o
obj-$(CONFIG_SMP) += platsmp.o headsmp.o
.phy_channel = 1,
};
-static struct platform_device *db8500_add_msp_i2s(struct device *parent,
- int id,
- resource_size_t base, int irq,
- struct msp_i2s_platform_data *pdata)
-{
- struct platform_device *pdev;
- struct resource res[] = {
- DEFINE_RES_MEM(base, SZ_4K),
- DEFINE_RES_IRQ(irq),
- };
-
- pr_info("Register platform-device 'ux500-msp-i2s', id %d, irq %d\n",
- id, irq);
- pdev = platform_device_register_resndata(parent, "ux500-msp-i2s", id,
- res, ARRAY_SIZE(res),
- pdata, sizeof(*pdata));
- if (!pdev) {
- pr_err("Failed to register platform-device 'ux500-msp-i2s.%d'!\n",
- id);
- return NULL;
- }
-
- return pdev;
-}
-
-/* Platform device for ASoC MOP500 machine */
-static struct platform_device snd_soc_mop500 = {
- .name = "snd-soc-mop500",
- .id = 0,
- .dev = {
- .platform_data = NULL,
- },
-};
-
struct msp_i2s_platform_data msp2_platform_data = {
.id = MSP_I2S_2,
.msp_i2s_dma_rx = &msp2_dma_rx,
.msp_i2s_dma_rx = &msp1_dma_rx,
.msp_i2s_dma_tx = NULL,
};
-
-void mop500_audio_init(struct device *parent)
-{
- pr_info("%s: Register platform-device 'snd-soc-mop500'.\n", __func__);
- platform_device_register(&snd_soc_mop500);
-
- pr_info("Initialize MSP I2S-devices.\n");
- db8500_add_msp_i2s(parent, 0, U8500_MSP0_BASE, IRQ_DB8500_MSP0,
- &msp0_platform_data);
- db8500_add_msp_i2s(parent, 1, U8500_MSP1_BASE, IRQ_DB8500_MSP1,
- &msp1_platform_data);
- db8500_add_msp_i2s(parent, 2, U8500_MSP2_BASE, IRQ_DB8500_MSP2,
- &msp2_platform_data);
- db8500_add_msp_i2s(parent, 3, U8500_MSP3_BASE, IRQ_DB8500_MSP1,
- &msp3_platform_data);
-}
#endif
};
-static void sdi0_configure(struct device *parent)
-{
- /* Add the device, force v2 to subrevision 1 */
- db8500_add_sdi0(parent, &mop500_sdi0_data, U8500_SDI_V2_PERIPHID);
-}
-
-void mop500_sdi_tc35892_init(struct device *parent)
-{
- mop500_sdi0_data.gpio_cd = GPIO_SDMMC_CD;
- sdi0_configure(parent);
-}
-
/*
* SDI1 (SDIO WLAN)
*/
.dma_tx_param = &mop500_sdi4_dma_cfg_tx,
#endif
};
-
-void __init mop500_sdi_init(struct device *parent)
-{
- /* PoP:ed eMMC */
- db8500_add_sdi2(parent, &mop500_sdi2_data, U8500_SDI_V2_PERIPHID);
- /* On-board eMMC */
- db8500_add_sdi4(parent, &mop500_sdi4_data, U8500_SDI_V2_PERIPHID);
-
- /*
- * On boards with the TC35892 GPIO expander, sdi0 will finally
- * be added when the TC35892 initializes and calls
- * mop500_sdi_tc35892_init() above.
- */
-}
-
-void __init snowball_sdi_init(struct device *parent)
-{
- /* On Snowball MMC_CAP_SD_HIGHSPEED isn't supported (Hardware issue?) */
- mop500_sdi0_data.capabilities &= ~MMC_CAP_SD_HIGHSPEED;
- /* On-board eMMC */
- db8500_add_sdi4(parent, &mop500_sdi4_data, U8500_SDI_V2_PERIPHID);
- /* External Micro SD slot */
- mop500_sdi0_data.gpio_cd = SNOWBALL_SDMMC_CD_GPIO;
- mop500_sdi0_data.cd_invert = true;
- sdi0_configure(parent);
-}
-
-void __init hrefv60_sdi_init(struct device *parent)
-{
- /* PoP:ed eMMC */
- db8500_add_sdi2(parent, &mop500_sdi2_data, U8500_SDI_V2_PERIPHID);
- /* On-board eMMC */
- db8500_add_sdi4(parent, &mop500_sdi4_data, U8500_SDI_V2_PERIPHID);
- /* External Micro SD slot */
- mop500_sdi0_data.gpio_cd = HREFV60_SDMMC_CD_GPIO;
- sdi0_configure(parent);
- /* WLAN SDIO channel */
- db8500_add_sdi1(parent, &mop500_sdi1_data, U8500_SDI_V2_PERIPHID);
-}
+++ /dev/null
-/*
- * Copyright (C) ST-Ericsson SA 2010
- *
- * License terms: GNU General Public License (GPL), version 2
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mfd/stmpe.h>
-#include <linux/input/bu21013.h>
-#include <linux/gpio.h>
-#include <linux/interrupt.h>
-#include <linux/i2c.h>
-#include <linux/input/matrix_keypad.h>
-#include <asm/mach-types.h>
-
-#include "board-mop500.h"
-
-/* STMPE/SKE keypad use this key layout */
-static const unsigned int mop500_keymap[] = {
- KEY(2, 5, KEY_END),
- KEY(4, 1, KEY_POWER),
- KEY(3, 5, KEY_VOLUMEDOWN),
- KEY(1, 3, KEY_3),
- KEY(5, 2, KEY_RIGHT),
- KEY(5, 0, KEY_9),
-
- KEY(0, 5, KEY_MENU),
- KEY(7, 6, KEY_ENTER),
- KEY(4, 5, KEY_0),
- KEY(6, 7, KEY_2),
- KEY(3, 4, KEY_UP),
- KEY(3, 3, KEY_DOWN),
-
- KEY(6, 4, KEY_SEND),
- KEY(6, 2, KEY_BACK),
- KEY(4, 2, KEY_VOLUMEUP),
- KEY(5, 5, KEY_1),
- KEY(4, 3, KEY_LEFT),
- KEY(3, 2, KEY_7),
-};
-
-static const struct matrix_keymap_data mop500_keymap_data = {
- .keymap = mop500_keymap,
- .keymap_size = ARRAY_SIZE(mop500_keymap),
-};
-/*
- * STMPE1601
- */
-static struct stmpe_keypad_platform_data stmpe1601_keypad_data = {
- .debounce_ms = 64,
- .scan_count = 8,
- .no_autorepeat = true,
- .keymap_data = &mop500_keymap_data,
-};
-
-static struct stmpe_platform_data stmpe1601_data = {
- .id = 1,
- .blocks = STMPE_BLOCK_KEYPAD,
- .irq_trigger = IRQF_TRIGGER_FALLING,
- .irq_base = MOP500_STMPE1601_IRQ(0),
- .keypad = &stmpe1601_keypad_data,
- .autosleep = true,
- .autosleep_timeout = 1024,
-};
-
-static struct i2c_board_info __initdata mop500_i2c0_devices_stuib[] = {
- {
- I2C_BOARD_INFO("stmpe1601", 0x40),
- .irq = NOMADIK_GPIO_TO_IRQ(218),
- .platform_data = &stmpe1601_data,
- .flags = I2C_CLIENT_WAKE,
- },
-};
-
-/*
- * BU21013 ROHM touchscreen interface on the STUIBs
- */
-
-#define TOUCH_GPIO_PIN 84
-
-#define TOUCH_XMAX 384
-#define TOUCH_YMAX 704
-
-#define PRCMU_CLOCK_OCR 0x1CC
-#define TSC_EXT_CLOCK_9_6MHZ 0x840000
-
-static struct bu21013_platform_device tsc_plat_device = {
- .touch_pin = TOUCH_GPIO_PIN,
- .touch_x_max = TOUCH_XMAX,
- .touch_y_max = TOUCH_YMAX,
- .ext_clk = false,
- .x_flip = false,
- .y_flip = true,
-};
-
-static struct i2c_board_info __initdata u8500_i2c3_devices_stuib[] = {
- {
- I2C_BOARD_INFO("bu21013_tp", 0x5C),
- .platform_data = &tsc_plat_device,
- },
- {
- I2C_BOARD_INFO("bu21013_tp", 0x5D),
- .platform_data = &tsc_plat_device,
- },
-};
-
-void __init mop500_stuib_init(void)
-{
- if (machine_is_hrefv60())
- tsc_plat_device.cs_pin = HREFV60_TOUCH_RST_GPIO;
- else
- tsc_plat_device.cs_pin = GPIO_BU21013_CS;
-
- mop500_uib_i2c_add(0, mop500_i2c0_devices_stuib,
- ARRAY_SIZE(mop500_i2c0_devices_stuib));
-
- mop500_uib_i2c_add(3, u8500_i2c3_devices_stuib,
- ARRAY_SIZE(u8500_i2c3_devices_stuib));
-}
+++ /dev/null
-/*
- * Copyright (C) ST-Ericsson SA 2010
- *
- * Board data for the U8500 UIB, also known as the New UIB
- * License terms: GNU General Public License (GPL), version 2
- */
-#include <linux/gpio.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/i2c.h>
-#include <linux/interrupt.h>
-#include <linux/mfd/tc3589x.h>
-#include <linux/input/matrix_keypad.h>
-
-#include "irqs.h"
-
-#include "board-mop500.h"
-
-static struct i2c_board_info __initdata mop500_i2c3_devices_u8500[] = {
- {
- I2C_BOARD_INFO("synaptics_rmi4_i2c", 0x4B),
- .irq = NOMADIK_GPIO_TO_IRQ(84),
- },
-};
-
-/*
- * TC35893
- */
-static const unsigned int u8500_keymap[] = {
- KEY(3, 1, KEY_END),
- KEY(4, 1, KEY_POWER),
- KEY(6, 4, KEY_VOLUMEDOWN),
- KEY(4, 2, KEY_EMAIL),
- KEY(3, 3, KEY_RIGHT),
- KEY(2, 5, KEY_BACKSPACE),
-
- KEY(6, 7, KEY_MENU),
- KEY(5, 0, KEY_ENTER),
- KEY(4, 3, KEY_0),
- KEY(3, 4, KEY_DOT),
- KEY(5, 2, KEY_UP),
- KEY(3, 5, KEY_DOWN),
-
- KEY(4, 5, KEY_SEND),
- KEY(0, 5, KEY_BACK),
- KEY(6, 2, KEY_VOLUMEUP),
- KEY(1, 3, KEY_SPACE),
- KEY(7, 6, KEY_LEFT),
- KEY(5, 5, KEY_SEARCH),
-};
-
-static struct matrix_keymap_data u8500_keymap_data = {
- .keymap = u8500_keymap,
- .keymap_size = ARRAY_SIZE(u8500_keymap),
-};
-
-static struct tc3589x_keypad_platform_data tc35893_data = {
- .krow = TC_KPD_ROWS,
- .kcol = TC_KPD_COLUMNS,
- .debounce_period = TC_KPD_DEBOUNCE_PERIOD,
- .settle_time = TC_KPD_SETTLE_TIME,
- .irqtype = IRQF_TRIGGER_FALLING,
- .enable_wakeup = true,
- .keymap_data = &u8500_keymap_data,
- .no_autorepeat = true,
-};
-
-static struct tc3589x_platform_data tc3589x_keypad_data = {
- .block = TC3589x_BLOCK_KEYPAD,
- .keypad = &tc35893_data,
- .irq_base = MOP500_EGPIO_IRQ_BASE,
-};
-
-static struct i2c_board_info __initdata mop500_i2c0_devices_u8500[] = {
- {
- I2C_BOARD_INFO("tc3589x", 0x44),
- .platform_data = &tc3589x_keypad_data,
- .irq = NOMADIK_GPIO_TO_IRQ(218),
- .flags = I2C_CLIENT_WAKE,
- },
-};
-
-
-void __init mop500_u8500uib_init(void)
-{
- mop500_uib_i2c_add(3, mop500_i2c3_devices_u8500,
- ARRAY_SIZE(mop500_i2c3_devices_u8500));
-
- mop500_uib_i2c_add(0, mop500_i2c0_devices_u8500,
- ARRAY_SIZE(mop500_i2c0_devices_u8500));
-
-}
+++ /dev/null
-/*
- * Copyright (C) ST-Ericsson SA 2010
- *
- * Author: Rabin Vincent <rabin.vincent@stericsson.com> for ST-Ericsson
- * License terms: GNU General Public License (GPL), version 2
- */
-
-#define pr_fmt(fmt) "mop500-uib: " fmt
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/i2c.h>
-
-#include "board-mop500.h"
-#include "id.h"
-
-enum mop500_uib {
- STUIB,
- U8500UIB,
-};
-
-struct uib {
- const char *name;
- const char *option;
- void (*init)(void);
-};
-
-static struct uib __initdata mop500_uibs[] = {
- [STUIB] = {
- .name = "ST-UIB",
- .option = "stuib",
- .init = mop500_stuib_init,
- },
- [U8500UIB] = {
- .name = "U8500-UIB",
- .option = "u8500uib",
- .init = mop500_u8500uib_init,
- },
-};
-
-static struct uib *mop500_uib;
-
-static int __init mop500_uib_setup(char *str)
-{
- int i;
-
- for (i = 0; i < ARRAY_SIZE(mop500_uibs); i++) {
- struct uib *uib = &mop500_uibs[i];
-
- if (!strcmp(str, uib->option)) {
- mop500_uib = uib;
- break;
- }
- }
-
- if (i == ARRAY_SIZE(mop500_uibs))
- pr_err("invalid uib= option (%s)\n", str);
-
- return 1;
-}
-__setup("uib=", mop500_uib_setup);
-
-/*
- * The UIBs are detected after the I2C host controllers are registered, so
- * i2c_register_board_info() can't be used.
- */
-void mop500_uib_i2c_add(int busnum, struct i2c_board_info *info,
- unsigned n)
-{
- struct i2c_adapter *adap;
- struct i2c_client *client;
- int i;
-
- adap = i2c_get_adapter(busnum);
- if (!adap) {
- pr_err("failed to get adapter i2c%d\n", busnum);
- return;
- }
-
- for (i = 0; i < n; i++) {
- client = i2c_new_device(adap, &info[i]);
- if (!client)
- pr_err("failed to register %s to i2c%d\n",
- info[i].type, busnum);
- }
-
- i2c_put_adapter(adap);
-}
-
-static void __init __mop500_uib_init(struct uib *uib, const char *why)
-{
- pr_info("%s (%s)\n", uib->name, why);
- uib->init();
-}
-
-/*
- * Detect the UIB attached based on the presence or absence of i2c devices.
- */
-int __init mop500_uib_init(void)
-{
- struct uib *uib = mop500_uib;
- struct i2c_adapter *i2c0;
- int ret;
-
- if (!cpu_is_u8500_family())
- return -ENODEV;
-
- if (uib) {
- __mop500_uib_init(uib, "from uib= boot argument");
- return 0;
- }
-
- i2c0 = i2c_get_adapter(0);
- if (!i2c0) {
- __mop500_uib_init(&mop500_uibs[STUIB],
- "fallback, could not get i2c0");
- return -ENODEV;
- }
-
- /* U8500-UIB has the TC35893 at 0x44 on I2C0, the ST-UIB doesn't. */
- ret = i2c_smbus_xfer(i2c0, 0x44, 0, I2C_SMBUS_WRITE, 0,
- I2C_SMBUS_QUICK, NULL);
- i2c_put_adapter(i2c0);
-
- if (ret == 0)
- uib = &mop500_uibs[U8500UIB];
- else
- uib = &mop500_uibs[STUIB];
-
- __mop500_uib_init(uib, "detected");
-
- return 0;
-}
#include <linux/platform_device.h>
#include <linux/clk.h>
#include <linux/io.h>
-#include <linux/i2c.h>
-#include <linux/platform_data/i2c-nomadik.h>
#include <linux/platform_data/db8500_thermal.h>
-#include <linux/gpio.h>
#include <linux/amba/bus.h>
#include <linux/amba/pl022.h>
-#include <linux/amba/serial.h>
-#include <linux/spi/spi.h>
#include <linux/mfd/abx500/ab8500.h>
#include <linux/regulator/ab8500.h>
#include <linux/regulator/fixed.h>
#include <linux/regulator/driver.h>
-#include <linux/regulator/gpio-regulator.h>
-#include <linux/mfd/tc3589x.h>
#include <linux/mfd/tps6105x.h>
-#include <linux/mfd/abx500/ab8500-gpio.h>
-#include <linux/mfd/abx500/ab8500-codec.h>
#include <linux/platform_data/leds-lp55xx.h>
#include <linux/input.h>
-#include <linux/smsc911x.h>
-#include <linux/gpio_keys.h>
#include <linux/delay.h>
#include <linux/leds.h>
#include <linux/pinctrl/consumer.h>
#include "setup.h"
#include "devices.h"
#include "irqs.h"
-#include <linux/platform_data/crypto-ux500.h>
#include "ste-dma40-db8500.h"
#include "db8500-regs.h"
#include "board-mop500.h"
#include "board-mop500-regulators.h"
-static struct gpio_led snowball_led_array[] = {
- {
- .name = "user_led",
- .default_trigger = "heartbeat",
- .gpio = 142,
- },
-};
-
-static struct gpio_led_platform_data snowball_led_data = {
- .leds = snowball_led_array,
- .num_leds = ARRAY_SIZE(snowball_led_array),
-};
-
-static struct platform_device snowball_led_dev = {
- .name = "leds-gpio",
- .dev = {
- .platform_data = &snowball_led_data,
- },
-};
-
-static struct fixed_voltage_config snowball_gpio_en_3v3_data = {
- .supply_name = "EN-3V3",
- .gpio = SNOWBALL_EN_3V3_ETH_GPIO,
- .microvolts = 3300000,
- .enable_high = 1,
- .init_data = &gpio_en_3v3_regulator,
- .startup_delay = 5000, /* 1200us */
-};
-
-static struct platform_device snowball_gpio_en_3v3_regulator_dev = {
- .name = "reg-fixed-voltage",
- .id = 1,
- .dev = {
- .platform_data = &snowball_gpio_en_3v3_data,
- },
-};
-
-/* Dynamically populated. */
-static struct gpio sdi0_reg_gpios[] = {
- { 0, GPIOF_OUT_INIT_LOW, "mmci_vsel" },
-};
-
-static struct gpio_regulator_state sdi0_reg_states[] = {
- { .value = 2900000, .gpios = (0 << 0) },
- { .value = 1800000, .gpios = (1 << 0) },
-};
-
-static struct gpio_regulator_config sdi0_reg_info = {
- .supply_name = "ext-mmc-level-shifter",
- .gpios = sdi0_reg_gpios,
- .nr_gpios = ARRAY_SIZE(sdi0_reg_gpios),
- .states = sdi0_reg_states,
- .nr_states = ARRAY_SIZE(sdi0_reg_states),
- .type = REGULATOR_VOLTAGE,
- .enable_high = 1,
- .enabled_at_boot = 0,
- .init_data = &sdi0_reg_init_data,
- .startup_delay = 100,
-};
-
-static struct platform_device sdi0_regulator = {
- .name = "gpio-regulator",
- .id = -1,
- .dev = {
- .platform_data = &sdi0_reg_info,
- },
-};
-
-static struct abx500_gpio_platform_data ab8500_gpio_pdata = {
- .gpio_base = MOP500_AB8500_PIN_GPIO(1),
-};
-
-/* ab8500-codec */
-static struct ab8500_codec_platform_data ab8500_codec_pdata = {
- .amics = {
- .mic1_type = AMIC_TYPE_DIFFERENTIAL,
- .mic2_type = AMIC_TYPE_DIFFERENTIAL,
- .mic1a_micbias = AMIC_MICBIAS_VAMIC1,
- .mic1b_micbias = AMIC_MICBIAS_VAMIC1,
- .mic2_micbias = AMIC_MICBIAS_VAMIC2
- },
- .ear_cmv = EAR_CMV_0_95V
-};
-
-static struct gpio_keys_button snowball_key_array[] = {
- {
- .gpio = 32,
- .type = EV_KEY,
- .code = KEY_1,
- .desc = "userpb",
- .active_low = 1,
- .debounce_interval = 50,
- .wakeup = 1,
- },
- {
- .gpio = 151,
- .type = EV_KEY,
- .code = KEY_2,
- .desc = "extkb1",
- .active_low = 1,
- .debounce_interval = 50,
- .wakeup = 1,
- },
- {
- .gpio = 152,
- .type = EV_KEY,
- .code = KEY_3,
- .desc = "extkb2",
- .active_low = 1,
- .debounce_interval = 50,
- .wakeup = 1,
- },
- {
- .gpio = 161,
- .type = EV_KEY,
- .code = KEY_4,
- .desc = "extkb3",
- .active_low = 1,
- .debounce_interval = 50,
- .wakeup = 1,
- },
- {
- .gpio = 162,
- .type = EV_KEY,
- .code = KEY_5,
- .desc = "extkb4",
- .active_low = 1,
- .debounce_interval = 50,
- .wakeup = 1,
- },
-};
-
-static struct gpio_keys_platform_data snowball_key_data = {
- .buttons = snowball_key_array,
- .nbuttons = ARRAY_SIZE(snowball_key_array),
-};
-
-static struct platform_device snowball_key_dev = {
- .name = "gpio-keys",
- .id = -1,
- .dev = {
- .platform_data = &snowball_key_data,
- }
-};
-
-static struct smsc911x_platform_config snowball_sbnet_cfg = {
- .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_HIGH,
- .irq_type = SMSC911X_IRQ_TYPE_PUSH_PULL,
- .flags = SMSC911X_USE_16BIT | SMSC911X_FORCE_INTERNAL_PHY,
- .shift = 1,
-};
-
-static struct resource sbnet_res[] = {
- {
- .name = "smsc911x-memory",
- .start = (0x5000 << 16),
- .end = (0x5000 << 16) + 0xffff,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = NOMADIK_GPIO_TO_IRQ(140),
- .end = NOMADIK_GPIO_TO_IRQ(140),
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
- },
-};
-
-static struct platform_device snowball_sbnet_dev = {
- .name = "smsc911x",
- .num_resources = ARRAY_SIZE(sbnet_res),
- .resource = sbnet_res,
- .dev = {
- .platform_data = &snowball_sbnet_cfg,
- },
-};
-
struct ab8500_platform_data ab8500_platdata = {
.irq_base = MOP500_AB8500_IRQ_BASE,
.regulator = &ab8500_regulator_plat_data,
- .gpio = &ab8500_gpio_pdata,
- .codec = &ab8500_codec_pdata,
-};
-
-static struct platform_device u8500_cpufreq_cooling_device = {
- .name = "db8500-cpufreq-cooling",
-};
-
-/*
- * TPS61052
- */
-
-static struct tps6105x_platform_data mop500_tps61052_data = {
- .mode = TPS6105X_MODE_VOLTAGE,
- .regulator_data = &tps61052_regulator,
-};
-
-/*
- * TC35892
- */
-
-static void mop500_tc35892_init(struct tc3589x *tc3589x, unsigned int base)
-{
- struct device *parent = NULL;
-#if 0
- /* FIXME: Is the sdi actually part of tc3589x? */
- parent = tc3589x->dev;
-#endif
- mop500_sdi_tc35892_init(parent);
-}
-
-static struct tc3589x_gpio_platform_data mop500_tc35892_gpio_data = {
- .gpio_base = MOP500_EGPIO(0),
- .setup = mop500_tc35892_init,
-};
-
-static struct tc3589x_platform_data mop500_tc35892_data = {
- .block = TC3589x_BLOCK_GPIO,
- .gpio = &mop500_tc35892_gpio_data,
- .irq_base = MOP500_EGPIO_IRQ_BASE,
-};
-
-static struct lp55xx_led_config lp5521_pri_led[] = {
- [0] = {
- .chan_nr = 0,
- .led_current = 0x2f,
- .max_current = 0x5f,
- },
- [1] = {
- .chan_nr = 1,
- .led_current = 0x2f,
- .max_current = 0x5f,
- },
- [2] = {
- .chan_nr = 2,
- .led_current = 0x2f,
- .max_current = 0x5f,
- },
-};
-
-static struct lp55xx_platform_data __initdata lp5521_pri_data = {
- .label = "lp5521_pri",
- .led_config = &lp5521_pri_led[0],
- .num_channels = 3,
- .clock_mode = LP55XX_CLOCK_EXT,
-};
-
-static struct lp55xx_led_config lp5521_sec_led[] = {
- [0] = {
- .chan_nr = 0,
- .led_current = 0x2f,
- .max_current = 0x5f,
- },
- [1] = {
- .chan_nr = 1,
- .led_current = 0x2f,
- .max_current = 0x5f,
- },
- [2] = {
- .chan_nr = 2,
- .led_current = 0x2f,
- .max_current = 0x5f,
- },
-};
-
-static struct lp55xx_platform_data __initdata lp5521_sec_data = {
- .label = "lp5521_sec",
- .led_config = &lp5521_sec_led[0],
- .num_channels = 3,
- .clock_mode = LP55XX_CLOCK_EXT,
-};
-
-/* I2C0 devices only available on the first HREF/MOP500 */
-static struct i2c_board_info __initdata mop500_i2c0_devices[] = {
- {
- I2C_BOARD_INFO("tc3589x", 0x42),
- .irq = NOMADIK_GPIO_TO_IRQ(217),
- .platform_data = &mop500_tc35892_data,
- },
- {
- I2C_BOARD_INFO("tps61052", 0x33),
- .platform_data = &mop500_tps61052_data,
- },
-};
-
-static struct i2c_board_info __initdata mop500_i2c2_devices[] = {
- {
- /* lp5521 LED driver, 1st device */
- I2C_BOARD_INFO("lp5521", 0x33),
- .platform_data = &lp5521_pri_data,
- },
- {
- /* lp5521 LED driver, 2st device */
- I2C_BOARD_INFO("lp5521", 0x34),
- .platform_data = &lp5521_sec_data,
- },
- {
- /* Light sensor Rohm BH1780GLI */
- I2C_BOARD_INFO("bh1780", 0x29),
- },
-};
-
-static int __init mop500_i2c_board_init(void)
-{
- if (machine_is_u8500())
- mop500_uib_i2c_add(0, mop500_i2c0_devices,
- ARRAY_SIZE(mop500_i2c0_devices));
- mop500_uib_i2c_add(2, mop500_i2c2_devices,
- ARRAY_SIZE(mop500_i2c2_devices));
- return 0;
-}
-device_initcall(mop500_i2c_board_init);
-
-static void __init mop500_i2c_init(struct device *parent)
-{
- db8500_add_i2c0(parent, NULL);
- db8500_add_i2c1(parent, NULL);
- db8500_add_i2c2(parent, NULL);
- db8500_add_i2c3(parent, NULL);
-}
-
-static struct gpio_keys_button mop500_gpio_keys[] = {
- {
- .desc = "SFH7741 Proximity Sensor",
- .type = EV_SW,
- .code = SW_FRONT_PROXIMITY,
- .active_low = 0,
- .can_disable = 1,
- }
-};
-
-static struct regulator *prox_regulator;
-static int mop500_prox_activate(struct device *dev);
-static void mop500_prox_deactivate(struct device *dev);
-
-static struct gpio_keys_platform_data mop500_gpio_keys_data = {
- .buttons = mop500_gpio_keys,
- .nbuttons = ARRAY_SIZE(mop500_gpio_keys),
- .enable = mop500_prox_activate,
- .disable = mop500_prox_deactivate,
-};
-
-static struct platform_device mop500_gpio_keys_device = {
- .name = "gpio-keys",
- .id = 0,
- .dev = {
- .platform_data = &mop500_gpio_keys_data,
- },
-};
-
-static int mop500_prox_activate(struct device *dev)
-{
- prox_regulator = regulator_get(&mop500_gpio_keys_device.dev,
- "vcc");
- if (IS_ERR(prox_regulator)) {
- dev_err(&mop500_gpio_keys_device.dev,
- "no regulator\n");
- return PTR_ERR(prox_regulator);
- }
-
- return regulator_enable(prox_regulator);
-}
-
-static void mop500_prox_deactivate(struct device *dev)
-{
- regulator_disable(prox_regulator);
- regulator_put(prox_regulator);
-}
-
-static struct cryp_platform_data u8500_cryp1_platform_data = {
- .mem_to_engine = {
- .dir = DMA_MEM_TO_DEV,
- .dev_type = DB8500_DMA_DEV48_CAC1,
- .mode = STEDMA40_MODE_LOGICAL,
- },
- .engine_to_mem = {
- .dir = DMA_DEV_TO_MEM,
- .dev_type = DB8500_DMA_DEV48_CAC1,
- .mode = STEDMA40_MODE_LOGICAL,
- }
-};
-
-static struct stedma40_chan_cfg u8500_hash_dma_cfg_tx = {
- .dir = DMA_MEM_TO_DEV,
- .dev_type = DB8500_DMA_DEV50_HAC1_TX,
- .mode = STEDMA40_MODE_LOGICAL,
-};
-
-static struct hash_platform_data u8500_hash1_platform_data = {
- .mem_to_engine = &u8500_hash_dma_cfg_tx,
- .dma_filter = stedma40_filter,
-};
-
-/* add any platform devices here - TODO */
-static struct platform_device *mop500_platform_devs[] __initdata = {
- &mop500_gpio_keys_device,
- &sdi0_regulator,
};
#ifdef CONFIG_STE_DMA40
*/
.num_chipselect = 5,
};
-
-static void __init mop500_spi_init(struct device *parent)
-{
- db8500_add_ssp0(parent, &ssp0_plat);
-}
-
-#ifdef CONFIG_STE_DMA40
-static struct stedma40_chan_cfg uart0_dma_cfg_rx = {
- .mode = STEDMA40_MODE_LOGICAL,
- .dir = DMA_DEV_TO_MEM,
- .dev_type = DB8500_DMA_DEV13_UART0,
-};
-
-static struct stedma40_chan_cfg uart0_dma_cfg_tx = {
- .mode = STEDMA40_MODE_LOGICAL,
- .dir = DMA_MEM_TO_DEV,
- .dev_type = DB8500_DMA_DEV13_UART0,
-};
-
-static struct stedma40_chan_cfg uart1_dma_cfg_rx = {
- .mode = STEDMA40_MODE_LOGICAL,
- .dir = DMA_DEV_TO_MEM,
- .dev_type = DB8500_DMA_DEV12_UART1,
-};
-
-static struct stedma40_chan_cfg uart1_dma_cfg_tx = {
- .mode = STEDMA40_MODE_LOGICAL,
- .dir = DMA_MEM_TO_DEV,
- .dev_type = DB8500_DMA_DEV12_UART1,
-};
-
-static struct stedma40_chan_cfg uart2_dma_cfg_rx = {
- .mode = STEDMA40_MODE_LOGICAL,
- .dir = DMA_DEV_TO_MEM,
- .dev_type = DB8500_DMA_DEV11_UART2,
-};
-
-static struct stedma40_chan_cfg uart2_dma_cfg_tx = {
- .mode = STEDMA40_MODE_LOGICAL,
- .dir = DMA_MEM_TO_DEV,
- .dev_type = DB8500_DMA_DEV11_UART2,
-};
-#endif
-
-struct amba_pl011_data uart0_plat = {
-#ifdef CONFIG_STE_DMA40
- .dma_filter = stedma40_filter,
- .dma_rx_param = &uart0_dma_cfg_rx,
- .dma_tx_param = &uart0_dma_cfg_tx,
-#endif
-};
-
-struct amba_pl011_data uart1_plat = {
-#ifdef CONFIG_STE_DMA40
- .dma_filter = stedma40_filter,
- .dma_rx_param = &uart1_dma_cfg_rx,
- .dma_tx_param = &uart1_dma_cfg_tx,
-#endif
-};
-
-struct amba_pl011_data uart2_plat = {
-#ifdef CONFIG_STE_DMA40
- .dma_filter = stedma40_filter,
- .dma_rx_param = &uart2_dma_cfg_rx,
- .dma_tx_param = &uart2_dma_cfg_tx,
-#endif
-};
-
-static void __init mop500_uart_init(struct device *parent)
-{
- db8500_add_uart0(parent, &uart0_plat);
- db8500_add_uart1(parent, &uart1_plat);
- db8500_add_uart2(parent, &uart2_plat);
-}
-
-static void __init u8500_cryp1_hash1_init(struct device *parent)
-{
- db8500_add_cryp1(parent, &u8500_cryp1_platform_data);
- db8500_add_hash1(parent, &u8500_hash1_platform_data);
-}
-
-static struct platform_device *snowball_platform_devs[] __initdata = {
- &snowball_led_dev,
- &snowball_key_dev,
- &snowball_sbnet_dev,
- &snowball_gpio_en_3v3_regulator_dev,
- &u8500_cpufreq_cooling_device,
- &sdi0_regulator,
-};
-
-static void __init mop500_init_machine(void)
-{
- struct device *parent = NULL;
- int i;
-
- platform_device_register(&db8500_prcmu_device);
- mop500_gpio_keys[0].gpio = GPIO_PROX_SENSOR;
-
- sdi0_reg_info.enable_gpio = GPIO_SDMMC_EN;
- sdi0_reg_info.gpios[0].gpio = GPIO_SDMMC_1V8_3V_SEL;
-
- mop500_pinmaps_init();
- parent = u8500_init_devices();
-
- for (i = 0; i < ARRAY_SIZE(mop500_platform_devs); i++)
- mop500_platform_devs[i]->dev.parent = parent;
-
- platform_add_devices(mop500_platform_devs,
- ARRAY_SIZE(mop500_platform_devs));
-
- mop500_i2c_init(parent);
- mop500_sdi_init(parent);
- mop500_spi_init(parent);
- mop500_audio_init(parent);
- mop500_uart_init(parent);
- u8500_cryp1_hash1_init(parent);
-
- /* This board has full regulator constraints */
- regulator_has_full_constraints();
-}
-
-
-static void __init snowball_init_machine(void)
-{
- struct device *parent = NULL;
- int i;
-
- platform_device_register(&db8500_prcmu_device);
-
- sdi0_reg_info.enable_gpio = SNOWBALL_SDMMC_EN_GPIO;
- sdi0_reg_info.gpios[0].gpio = SNOWBALL_SDMMC_1V8_3V_GPIO;
-
- snowball_pinmaps_init();
- parent = u8500_init_devices();
-
- for (i = 0; i < ARRAY_SIZE(snowball_platform_devs); i++)
- snowball_platform_devs[i]->dev.parent = parent;
-
- platform_add_devices(snowball_platform_devs,
- ARRAY_SIZE(snowball_platform_devs));
-
- mop500_i2c_init(parent);
- snowball_sdi_init(parent);
- mop500_spi_init(parent);
- mop500_audio_init(parent);
- mop500_uart_init(parent);
-
- u8500_cryp1_hash1_init(parent);
-
- /* This board has full regulator constraints */
- regulator_has_full_constraints();
-}
-
-static void __init hrefv60_init_machine(void)
-{
- struct device *parent = NULL;
- int i;
-
- platform_device_register(&db8500_prcmu_device);
- /*
- * The HREFv60 board removed a GPIO expander and routed
- * all these GPIO pins to the internal GPIO controller
- * instead.
- */
- mop500_gpio_keys[0].gpio = HREFV60_PROX_SENSE_GPIO;
-
- sdi0_reg_info.enable_gpio = HREFV60_SDMMC_EN_GPIO;
- sdi0_reg_info.gpios[0].gpio = HREFV60_SDMMC_1V8_3V_GPIO;
-
- hrefv60_pinmaps_init();
- parent = u8500_init_devices();
-
- for (i = 0; i < ARRAY_SIZE(mop500_platform_devs); i++)
- mop500_platform_devs[i]->dev.parent = parent;
-
- platform_add_devices(mop500_platform_devs,
- ARRAY_SIZE(mop500_platform_devs));
-
- mop500_i2c_init(parent);
- hrefv60_sdi_init(parent);
- mop500_spi_init(parent);
- mop500_audio_init(parent);
- mop500_uart_init(parent);
-
- /* This board has full regulator constraints */
- regulator_has_full_constraints();
-}
-
-MACHINE_START(U8500, "ST-Ericsson MOP500 platform")
- /* Maintainer: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> */
- .atag_offset = 0x100,
- .smp = smp_ops(ux500_smp_ops),
- .map_io = u8500_map_io,
- .init_irq = ux500_init_irq,
- /* we re-use nomadik timer here */
- .init_time = ux500_timer_init,
- .init_machine = mop500_init_machine,
- .init_late = ux500_init_late,
- .restart = ux500_restart,
-MACHINE_END
-
-MACHINE_START(U8520, "ST-Ericsson U8520 Platform HREFP520")
- .atag_offset = 0x100,
- .map_io = u8500_map_io,
- .init_irq = ux500_init_irq,
- .init_time = ux500_timer_init,
- .init_machine = mop500_init_machine,
- .init_late = ux500_init_late,
- .restart = ux500_restart,
-MACHINE_END
-
-MACHINE_START(HREFV60, "ST-Ericsson U8500 Platform HREFv60+")
- .atag_offset = 0x100,
- .smp = smp_ops(ux500_smp_ops),
- .map_io = u8500_map_io,
- .init_irq = ux500_init_irq,
- .init_time = ux500_timer_init,
- .init_machine = hrefv60_init_machine,
- .init_late = ux500_init_late,
- .restart = ux500_restart,
-MACHINE_END
-
-MACHINE_START(SNOWBALL, "Calao Systems Snowball platform")
- .atag_offset = 0x100,
- .smp = smp_ops(ux500_smp_ops),
- .map_io = u8500_map_io,
- .init_irq = ux500_init_irq,
- /* we re-use nomadik timer here */
- .init_time = ux500_timer_init,
- .init_machine = snowball_init_machine,
- .init_late = NULL,
- .restart = ux500_restart,
-MACHINE_END
#define SNOWBALL_EN_3V3_ETH_GPIO MOP500_AB8500_PIN_GPIO(26) /* GPIO26 */
struct device;
-struct i2c_board_info;
extern struct mmci_platform_data mop500_sdi0_data;
extern struct mmci_platform_data mop500_sdi1_data;
extern struct mmci_platform_data mop500_sdi2_data;
extern struct msp_i2s_platform_data msp1_platform_data;
extern struct msp_i2s_platform_data msp2_platform_data;
extern struct msp_i2s_platform_data msp3_platform_data;
-extern struct arm_pmu_platdata db8500_pmu_platdata;
-extern struct amba_pl011_data uart0_plat;
-extern struct amba_pl011_data uart1_plat;
-extern struct amba_pl011_data uart2_plat;
extern struct pl022_ssp_controller ssp0_plat;
-extern struct stedma40_platform_data dma40_plat_data;
-extern void mop500_sdi_init(struct device *parent);
-extern void snowball_sdi_init(struct device *parent);
-extern void hrefv60_sdi_init(struct device *parent);
-extern void mop500_sdi_tc35892_init(struct device *parent);
-void __init mop500_u8500uib_init(void);
-void __init mop500_stuib_init(void);
void __init mop500_pinmaps_init(void);
void __init snowball_pinmaps_init(void);
void __init hrefv60_pinmaps_init(void);
-void mop500_audio_init(struct device *parent);
-int __init mop500_uib_init(void);
-void mop500_uib_i2c_add(int busnum, struct i2c_board_info *info,
- unsigned n);
#endif
#include "irqs.h"
#include "devices-db8500.h"
-#include "ste-dma40-db8500.h"
#include "db8500-regs.h"
#include "board-mop500.h"
#include "id.h"
iotable_init(u8500_io_desc, ARRAY_SIZE(u8500_io_desc));
}
-static struct resource db8500_pmu_resources[] = {
- [0] = {
- .start = IRQ_DB8500_PMU,
- .end = IRQ_DB8500_PMU,
- .flags = IORESOURCE_IRQ,
- },
-};
-
/*
* The PMU IRQ lines of two cores are wired together into a single interrupt.
* Bounce the interrupt to the other core if it's not ours.
.handle_irq = db8500_pmu_handler,
};
-static struct platform_device db8500_pmu_device = {
- .name = "arm-pmu",
- .id = -1,
- .num_resources = ARRAY_SIZE(db8500_pmu_resources),
- .resource = db8500_pmu_resources,
- .dev.platform_data = &db8500_pmu_platdata,
-};
-
-static struct platform_device *platform_devs[] __initdata = {
- &u8500_dma40_device,
- &db8500_pmu_device,
-};
-
-static resource_size_t __initdata db8500_gpio_base[] = {
- U8500_GPIOBANK0_BASE,
- U8500_GPIOBANK1_BASE,
- U8500_GPIOBANK2_BASE,
- U8500_GPIOBANK3_BASE,
- U8500_GPIOBANK4_BASE,
- U8500_GPIOBANK5_BASE,
- U8500_GPIOBANK6_BASE,
- U8500_GPIOBANK7_BASE,
- U8500_GPIOBANK8_BASE,
-};
-
-static void __init db8500_add_gpios(struct device *parent)
-{
- struct nmk_gpio_platform_data pdata = {
- .supports_sleepmode = true,
- };
-
- dbx500_add_gpios(parent, db8500_gpio_base,
- ARRAY_SIZE(db8500_gpio_base),
- IRQ_DB8500_GPIO0, &pdata);
- dbx500_add_pinctrl(parent, "pinctrl-db8500", U8500_PRCMU_BASE);
-}
-
-static int usb_db8500_dma_cfg[] = {
- DB8500_DMA_DEV38_USB_OTG_IEP_AND_OEP_1_9,
- DB8500_DMA_DEV37_USB_OTG_IEP_AND_OEP_2_10,
- DB8500_DMA_DEV36_USB_OTG_IEP_AND_OEP_3_11,
- DB8500_DMA_DEV19_USB_OTG_IEP_AND_OEP_4_12,
- DB8500_DMA_DEV18_USB_OTG_IEP_AND_OEP_5_13,
- DB8500_DMA_DEV17_USB_OTG_IEP_AND_OEP_6_14,
- DB8500_DMA_DEV16_USB_OTG_IEP_AND_OEP_7_15,
- DB8500_DMA_DEV39_USB_OTG_IEP_AND_OEP_8
-};
-
static const char *db8500_read_soc_id(void)
{
void __iomem *uid = __io_address(U8500_BB_UID_BASE);
return ux500_soc_device_init(soc_id);
}
-/*
- * This function is called from the board init
- */
-struct device * __init u8500_init_devices(void)
-{
- struct device *parent;
- int i;
-
- parent = db8500_soc_device_init();
-
- db8500_add_rtc(parent);
- db8500_add_gpios(parent);
- db8500_add_usb(parent, usb_db8500_dma_cfg, usb_db8500_dma_cfg);
-
- for (i = 0; i < ARRAY_SIZE(platform_devs); i++)
- platform_devs[i]->dev.parent = parent;
-
- platform_add_devices(platform_devs, ARRAY_SIZE(platform_devs));
-
- return parent;
-}
-
#ifdef CONFIG_MACH_UX500_DT
static struct of_dev_auxdata u8500_auxdata_lookup[] __initdata = {
/* Requires call-back bindings. */
OF_DEV_AUXDATA("arm,cortex-a9-pmu", 0, "arm-pmu", &db8500_pmu_platdata),
/* Requires DMA bindings. */
- OF_DEV_AUXDATA("arm,pl011", 0x80120000, "uart0", NULL),
- OF_DEV_AUXDATA("arm,pl011", 0x80121000, "uart1", NULL),
- OF_DEV_AUXDATA("arm,pl011", 0x80007000, "uart2", NULL),
- OF_DEV_AUXDATA("arm,pl022", 0x80002000, "ssp0", &ssp0_plat),
- OF_DEV_AUXDATA("arm,pl18x", 0x80126000, "sdi0", NULL),
- OF_DEV_AUXDATA("arm,pl18x", 0x80118000, "sdi1", NULL),
- OF_DEV_AUXDATA("arm,pl18x", 0x80005000, "sdi2", NULL),
- OF_DEV_AUXDATA("arm,pl18x", 0x80114000, "sdi4", NULL),
- /* Requires clock name bindings. */
- OF_DEV_AUXDATA("st,nomadik-gpio", 0x8012e000, "gpio.0", NULL),
- OF_DEV_AUXDATA("st,nomadik-gpio", 0x8012e080, "gpio.1", NULL),
- OF_DEV_AUXDATA("st,nomadik-gpio", 0x8000e000, "gpio.2", NULL),
- OF_DEV_AUXDATA("st,nomadik-gpio", 0x8000e080, "gpio.3", NULL),
- OF_DEV_AUXDATA("st,nomadik-gpio", 0x8000e100, "gpio.4", NULL),
- OF_DEV_AUXDATA("st,nomadik-gpio", 0x8000e180, "gpio.5", NULL),
- OF_DEV_AUXDATA("st,nomadik-gpio", 0x8011e000, "gpio.6", NULL),
- OF_DEV_AUXDATA("st,nomadik-gpio", 0x8011e080, "gpio.7", NULL),
- OF_DEV_AUXDATA("st,nomadik-gpio", 0xa03fe000, "gpio.8", NULL),
- OF_DEV_AUXDATA("st,nomadik-i2c", 0x80004000, "nmk-i2c.0", NULL),
- OF_DEV_AUXDATA("st,nomadik-i2c", 0x80122000, "nmk-i2c.1", NULL),
- OF_DEV_AUXDATA("st,nomadik-i2c", 0x80128000, "nmk-i2c.2", NULL),
- OF_DEV_AUXDATA("st,nomadik-i2c", 0x80110000, "nmk-i2c.3", NULL),
- OF_DEV_AUXDATA("st,nomadik-i2c", 0x8012a000, "nmk-i2c.4", NULL),
- OF_DEV_AUXDATA("stericsson,db8500-musb", 0xa03e0000, "musb-ux500.0", NULL),
+ OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80123000,
+ "ux500-msp-i2s.0", &msp0_platform_data),
+ OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80124000,
+ "ux500-msp-i2s.1", &msp1_platform_data),
+ OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80117000,
+ "ux500-msp-i2s.2", &msp2_platform_data),
+ OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80125000,
+ "ux500-msp-i2s.3", &msp3_platform_data),
+ /* Requires non-DT:able platform data. */
OF_DEV_AUXDATA("stericsson,db8500-prcmu", 0x80157000, "db8500-prcmu",
&db8500_prcmu_pdata),
- OF_DEV_AUXDATA("smsc,lan9115", 0x50000000, "smsc911x.0", NULL),
OF_DEV_AUXDATA("stericsson,ux500-cryp", 0xa03cb000, "cryp1", NULL),
OF_DEV_AUXDATA("stericsson,ux500-hash", 0xa03c2000, "hash1", NULL),
OF_DEV_AUXDATA("stericsson,snd-soc-mop500", 0, "snd-soc-mop500.0",
/* Requires device name bindings. */
OF_DEV_AUXDATA("stericsson,db8500-pinctrl", U8500_PRCMU_BASE,
"pinctrl-db8500", NULL),
- /* Requires clock name and DMA bindings. */
- OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80123000,
- "ux500-msp-i2s.0", &msp0_platform_data),
- OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80124000,
- "ux500-msp-i2s.1", &msp1_platform_data),
- OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80117000,
- "ux500-msp-i2s.2", &msp2_platform_data),
- OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80125000,
- "ux500-msp-i2s.3", &msp3_platform_data),
- /* Requires clock name bindings and channel address lookup table. */
- OF_DEV_AUXDATA("stericsson,db8500-dma40", 0x801C0000, "dma40.0", NULL),
{},
};
if (cpu_is_u8500_family()) {
prcmu_early_init(U8500_PRCMU_BASE, SZ_8K - 1);
ux500_pm_init(U8500_PRCMU_BASE, SZ_8K - 1);
- u8500_clk_init(U8500_CLKRST1_BASE, U8500_CLKRST2_BASE,
- U8500_CLKRST3_BASE, U8500_CLKRST5_BASE,
- U8500_CLKRST6_BASE);
+
+ if (of_have_populated_dt())
+ u8500_of_clk_init(U8500_CLKRST1_BASE,
+ U8500_CLKRST2_BASE,
+ U8500_CLKRST3_BASE,
+ U8500_CLKRST5_BASE,
+ U8500_CLKRST6_BASE);
+ else
+ u8500_clk_init(U8500_CLKRST1_BASE, U8500_CLKRST2_BASE,
+ U8500_CLKRST3_BASE, U8500_CLKRST5_BASE,
+ U8500_CLKRST6_BASE);
} else if (cpu_is_u9540()) {
prcmu_early_init(U8500_PRCMU_BASE, SZ_8K - 1);
ux500_pm_init(U8500_PRCMU_BASE, SZ_8K - 1);
}
}
-void __init ux500_init_late(void)
-{
- mop500_uib_init();
-}
-
static const char * __init ux500_get_machine(void)
{
return kasprintf(GFP_KERNEL, "DB%4x", dbx500_partnumber());
+++ /dev/null
-/*
- * Copyright (C) ST-Ericsson SA 2010
- *
- * Author: Rabin Vincent <rabin.vincent@stericsson.com> for ST-Ericsson
- * License terms: GNU General Public License (GPL), version 2.
- */
-
-#include <linux/kernel.h>
-#include <linux/dma-mapping.h>
-#include <linux/err.h>
-#include <linux/irq.h>
-#include <linux/slab.h>
-#include <linux/platform_device.h>
-#include <linux/platform_data/pinctrl-nomadik.h>
-
-#include "irqs.h"
-
-#include "devices-common.h"
-
-static struct platform_device *
-dbx500_add_gpio(struct device *parent, int id, resource_size_t addr, int irq,
- struct nmk_gpio_platform_data *pdata)
-{
- struct resource resources[] = {
- {
- .start = addr,
- .end = addr + 127,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = irq,
- .end = irq,
- .flags = IORESOURCE_IRQ,
- }
- };
-
- return platform_device_register_resndata(
- parent,
- "gpio",
- id,
- resources,
- ARRAY_SIZE(resources),
- pdata,
- sizeof(*pdata));
-}
-
-void dbx500_add_gpios(struct device *parent, resource_size_t *base, int num,
- int irq, struct nmk_gpio_platform_data *pdata)
-{
- int first = 0;
- int i;
-
- for (i = 0; i < num; i++, first += 32, irq++) {
- pdata->first_gpio = first;
- pdata->first_irq = NOMADIK_GPIO_TO_IRQ(first);
- pdata->num_gpio = 32;
-
- dbx500_add_gpio(parent, i, base[i], irq, pdata);
- }
-}
+++ /dev/null
-/*
- * Copyright (C) ST-Ericsson SA 2010
- *
- * Author: Rabin Vincent <rabin.vincent@stericsson.com> for ST-Ericsson
- * License terms: GNU General Public License (GPL), version 2.
- */
-
-#ifndef __DEVICES_COMMON_H
-#define __DEVICES_COMMON_H
-
-#include <linux/platform_device.h>
-#include <linux/dma-mapping.h>
-#include <linux/sys_soc.h>
-#include <linux/amba/bus.h>
-#include <linux/platform_data/i2c-nomadik.h>
-#include <linux/platform_data/crypto-ux500.h>
-
-struct spi_master_cntlr;
-
-static inline struct amba_device *
-dbx500_add_msp_spi(struct device *parent, const char *name,
- resource_size_t base, int irq,
- struct spi_master_cntlr *pdata)
-{
- return amba_ahb_device_add(parent, name, base, SZ_4K, irq, 0,
- pdata, 0);
-}
-
-static inline struct amba_device *
-dbx500_add_spi(struct device *parent, const char *name, resource_size_t base,
- int irq, struct spi_master_cntlr *pdata,
- u32 periphid)
-{
- return amba_ahb_device_add(parent, name, base, SZ_4K, irq, 0,
- pdata, periphid);
-}
-
-struct mmci_platform_data;
-
-static inline struct amba_device *
-dbx500_add_sdi(struct device *parent, const char *name, resource_size_t base,
- int irq, struct mmci_platform_data *pdata, u32 periphid)
-{
- return amba_ahb_device_add(parent, name, base, SZ_4K, irq, 0,
- pdata, periphid);
-}
-
-struct amba_pl011_data;
-
-static inline struct amba_device *
-dbx500_add_uart(struct device *parent, const char *name, resource_size_t base,
- int irq, struct amba_pl011_data *pdata)
-{
- return amba_ahb_device_add(parent, name, base, SZ_4K, irq, 0, pdata, 0);
-}
-
-struct nmk_i2c_controller;
-
-static inline struct amba_device *
-dbx500_add_i2c(struct device *parent, int id, resource_size_t base, int irq,
- struct nmk_i2c_controller *data)
-{
- /* Conjure a name similar to what the platform device used to have */
- char name[16];
-
- snprintf(name, sizeof(name), "nmk-i2c.%d", id);
- return amba_apb_device_add(parent, name, base, SZ_4K, irq, 0, data, 0);
-}
-
-static inline struct amba_device *
-dbx500_add_rtc(struct device *parent, resource_size_t base, int irq)
-{
- return amba_apb_device_add(parent, "rtc-pl031", base, SZ_4K, irq,
- 0, NULL, 0);
-}
-
-struct cryp_platform_data;
-
-static inline struct platform_device *
-dbx500_add_cryp1(struct device *parent, int id, resource_size_t base, int irq,
- struct cryp_platform_data *pdata)
-{
- struct resource res[] = {
- DEFINE_RES_MEM(base, SZ_4K),
- DEFINE_RES_IRQ(irq),
- };
-
- struct platform_device_info pdevinfo = {
- .parent = parent,
- .name = "cryp1",
- .id = id,
- .res = res,
- .num_res = ARRAY_SIZE(res),
- .data = pdata,
- .size_data = sizeof(*pdata),
- .dma_mask = DMA_BIT_MASK(32),
- };
-
- return platform_device_register_full(&pdevinfo);
-}
-
-struct hash_platform_data;
-
-static inline struct platform_device *
-dbx500_add_hash1(struct device *parent, int id, resource_size_t base,
- struct hash_platform_data *pdata)
-{
- struct resource res[] = {
- DEFINE_RES_MEM(base, SZ_4K),
- };
-
- struct platform_device_info pdevinfo = {
- .parent = parent,
- .name = "hash1",
- .id = id,
- .res = res,
- .num_res = ARRAY_SIZE(res),
- .data = pdata,
- .size_data = sizeof(*pdata),
- .dma_mask = DMA_BIT_MASK(32),
- };
-
- return platform_device_register_full(&pdevinfo);
-}
-
-struct nmk_gpio_platform_data;
-
-void dbx500_add_gpios(struct device *parent, resource_size_t *base, int num,
- int irq, struct nmk_gpio_platform_data *pdata);
-
-static inline void
-dbx500_add_pinctrl(struct device *parent, const char *name,
- resource_size_t base)
-{
- struct resource res[] = {
- DEFINE_RES_MEM(base, SZ_8K),
- };
- struct platform_device_info pdevinfo = {
- .parent = parent,
- .name = name,
- .id = -1,
- .res = res,
- .num_res = ARRAY_SIZE(res),
- };
-
- platform_device_register_full(&pdevinfo);
-}
-
-#endif
#include <linux/platform_device.h>
#include <linux/interrupt.h>
#include <linux/io.h>
-#include <linux/gpio.h>
#include <linux/amba/bus.h>
#include <linux/amba/pl022.h>
-#include <linux/platform_data/dma-ste-dma40.h>
#include <linux/mfd/dbx500-prcmu.h>
#include "setup.h"
#include "db8500-regs.h"
#include "devices-db8500.h"
-#include "ste-dma40-db8500.h"
-
-static struct resource dma40_resources[] = {
- [0] = {
- .start = U8500_DMA_BASE,
- .end = U8500_DMA_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- .name = "base",
- },
- [1] = {
- .start = U8500_DMA_LCPA_BASE,
- .end = U8500_DMA_LCPA_BASE + 2 * SZ_1K - 1,
- .flags = IORESOURCE_MEM,
- .name = "lcpa",
- },
- [2] = {
- .start = IRQ_DB8500_DMA,
- .end = IRQ_DB8500_DMA,
- .flags = IORESOURCE_IRQ,
- }
-};
-
-struct stedma40_platform_data dma40_plat_data = {
- .disabled_channels = {-1},
-};
-
-struct platform_device u8500_dma40_device = {
- .dev = {
- .platform_data = &dma40_plat_data,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .name = "dma40",
- .id = 0,
- .num_resources = ARRAY_SIZE(dma40_resources),
- .resource = dma40_resources
-};
-
-struct resource keypad_resources[] = {
- [0] = {
- .start = U8500_SKE_BASE,
- .end = U8500_SKE_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = IRQ_DB8500_KB,
- .end = IRQ_DB8500_KB,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-struct platform_device u8500_ske_keypad_device = {
- .name = "nmk-ske-keypad",
- .id = -1,
- .num_resources = ARRAY_SIZE(keypad_resources),
- .resource = keypad_resources,
-};
struct prcmu_pdata db8500_prcmu_pdata = {
.ab_platdata = &ab8500_platdata,
.version_offset = DB8500_PRCMU_FW_VERSION_OFFSET,
.legacy_offset = DB8500_PRCMU_LEGACY_OFFSET,
};
-
-static struct resource db8500_prcmu_res[] = {
- {
- .name = "prcmu",
- .start = U8500_PRCMU_BASE,
- .end = U8500_PRCMU_BASE + SZ_8K - 1,
- .flags = IORESOURCE_MEM,
- },
- {
- .name = "prcmu-tcdm",
- .start = U8500_PRCMU_TCDM_BASE,
- .end = U8500_PRCMU_TCDM_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
- {
- .name = "irq",
- .start = IRQ_DB8500_PRCMU1,
- .end = IRQ_DB8500_PRCMU1,
- .flags = IORESOURCE_IRQ,
- },
- {
- .name = "prcmu-tcpm",
- .start = U8500_PRCMU_TCPM_BASE,
- .end = U8500_PRCMU_TCPM_BASE + SZ_32K - 1,
- .flags = IORESOURCE_MEM,
- },
-};
-
-struct platform_device db8500_prcmu_device = {
- .name = "db8500-prcmu",
- .resource = db8500_prcmu_res,
- .num_resources = ARRAY_SIZE(db8500_prcmu_res),
- .dev = {
- .platform_data = &db8500_prcmu_pdata,
- },
-};
#ifndef __DEVICES_DB8500_H
#define __DEVICES_DB8500_H
-#include <linux/platform_data/usb-musb-ux500.h>
#include "irqs.h"
#include "db8500-regs.h"
-#include "devices-common.h"
-struct ske_keypad_platform_data;
-struct pl022_ssp_controller;
struct platform_device;
extern struct ab8500_platform_data ab8500_platdata;
extern struct prcmu_pdata db8500_prcmu_pdata;
-extern struct platform_device db8500_prcmu_device;
-static inline struct platform_device *
-db8500_add_ske_keypad(struct device *parent,
- struct ske_keypad_platform_data *pdata,
- size_t size)
-{
- struct resource resources[] = {
- DEFINE_RES_MEM(U8500_SKE_BASE, SZ_4K),
- DEFINE_RES_IRQ(IRQ_DB8500_KB),
- };
-
- return platform_device_register_resndata(parent, "nmk-ske-keypad", -1,
- resources, 2, pdata, size);
-}
-
-static inline struct amba_device *
-db8500_add_ssp(struct device *parent, const char *name, resource_size_t base,
- int irq, struct pl022_ssp_controller *pdata)
-{
- return amba_ahb_device_add(parent, name, base, SZ_4K, irq, 0, pdata, 0);
-}
-
-#define db8500_add_i2c0(parent, pdata) \
- dbx500_add_i2c(parent, 0, U8500_I2C0_BASE, IRQ_DB8500_I2C0, pdata)
-#define db8500_add_i2c1(parent, pdata) \
- dbx500_add_i2c(parent, 1, U8500_I2C1_BASE, IRQ_DB8500_I2C1, pdata)
-#define db8500_add_i2c2(parent, pdata) \
- dbx500_add_i2c(parent, 2, U8500_I2C2_BASE, IRQ_DB8500_I2C2, pdata)
-#define db8500_add_i2c3(parent, pdata) \
- dbx500_add_i2c(parent, 3, U8500_I2C3_BASE, IRQ_DB8500_I2C3, pdata)
-#define db8500_add_i2c4(parent, pdata) \
- dbx500_add_i2c(parent, 4, U8500_I2C4_BASE, IRQ_DB8500_I2C4, pdata)
-
-#define db8500_add_msp0_spi(parent, pdata) \
- dbx500_add_msp_spi(parent, "msp0", U8500_MSP0_BASE, \
- IRQ_DB8500_MSP0, pdata)
-#define db8500_add_msp1_spi(parent, pdata) \
- dbx500_add_msp_spi(parent, "msp1", U8500_MSP1_BASE, \
- IRQ_DB8500_MSP1, pdata)
-#define db8500_add_msp2_spi(parent, pdata) \
- dbx500_add_msp_spi(parent, "msp2", U8500_MSP2_BASE, \
- IRQ_DB8500_MSP2, pdata)
-#define db8500_add_msp3_spi(parent, pdata) \
- dbx500_add_msp_spi(parent, "msp3", U8500_MSP3_BASE, \
- IRQ_DB8500_MSP1, pdata)
-
-#define db8500_add_rtc(parent) \
- dbx500_add_rtc(parent, U8500_RTC_BASE, IRQ_DB8500_RTC);
-
-#define db8500_add_usb(parent, rx_cfg, tx_cfg) \
- ux500_add_usb(parent, U8500_USBOTG_BASE, \
- IRQ_DB8500_USBOTG, rx_cfg, tx_cfg)
-
-#define db8500_add_sdi0(parent, pdata, pid) \
- dbx500_add_sdi(parent, "sdi0", U8500_SDI0_BASE, \
- IRQ_DB8500_SDMMC0, pdata, pid)
-#define db8500_add_sdi1(parent, pdata, pid) \
- dbx500_add_sdi(parent, "sdi1", U8500_SDI1_BASE, \
- IRQ_DB8500_SDMMC1, pdata, pid)
-#define db8500_add_sdi2(parent, pdata, pid) \
- dbx500_add_sdi(parent, "sdi2", U8500_SDI2_BASE, \
- IRQ_DB8500_SDMMC2, pdata, pid)
-#define db8500_add_sdi3(parent, pdata, pid) \
- dbx500_add_sdi(parent, "sdi3", U8500_SDI3_BASE, \
- IRQ_DB8500_SDMMC3, pdata, pid)
-#define db8500_add_sdi4(parent, pdata, pid) \
- dbx500_add_sdi(parent, "sdi4", U8500_SDI4_BASE, \
- IRQ_DB8500_SDMMC4, pdata, pid)
-#define db8500_add_sdi5(parent, pdata, pid) \
- dbx500_add_sdi(parent, "sdi5", U8500_SDI5_BASE, \
- IRQ_DB8500_SDMMC5, pdata, pid)
-
-#define db8500_add_ssp0(parent, pdata) \
- db8500_add_ssp(parent, "ssp0", U8500_SSP0_BASE, \
- IRQ_DB8500_SSP0, pdata)
-#define db8500_add_ssp1(parent, pdata) \
- db8500_add_ssp(parent, "ssp1", U8500_SSP1_BASE, \
- IRQ_DB8500_SSP1, pdata)
-
-#define db8500_add_spi0(parent, pdata) \
- dbx500_add_spi(parent, "spi0", U8500_SPI0_BASE, \
- IRQ_DB8500_SPI0, pdata, 0)
-#define db8500_add_spi1(parent, pdata) \
- dbx500_add_spi(parent, "spi1", U8500_SPI1_BASE, \
- IRQ_DB8500_SPI1, pdata, 0)
-#define db8500_add_spi2(parent, pdata) \
- dbx500_add_spi(parent, "spi2", U8500_SPI2_BASE, \
- IRQ_DB8500_SPI2, pdata, 0)
-#define db8500_add_spi3(parent, pdata) \
- dbx500_add_spi(parent, "spi3", U8500_SPI3_BASE, \
- IRQ_DB8500_SPI3, pdata, 0)
-
-#define db8500_add_uart0(parent, pdata) \
- dbx500_add_uart(parent, "uart0", U8500_UART0_BASE, \
- IRQ_DB8500_UART0, pdata)
-#define db8500_add_uart1(parent, pdata) \
- dbx500_add_uart(parent, "uart1", U8500_UART1_BASE, \
- IRQ_DB8500_UART1, pdata)
-#define db8500_add_uart2(parent, pdata) \
- dbx500_add_uart(parent, "uart2", U8500_UART2_BASE, \
- IRQ_DB8500_UART2, pdata)
-
-#define db8500_add_cryp1(parent, pdata) \
- dbx500_add_cryp1(parent, -1, U8500_CRYP1_BASE, IRQ_DB8500_CRYP1, pdata)
-#define db8500_add_hash1(parent, pdata) \
- dbx500_add_hash1(parent, -1, U8500_HASH1_BASE, pdata)
#endif
struct platform_device;
struct amba_device;
-extern struct platform_device u8500_gpio_devs[];
-
extern struct amba_device ux500_pl031_device;
-extern struct platform_device ux500_hash1_device;
-extern struct platform_device ux500_cryp1_device;
-
-extern struct platform_device u8500_dma40_device;
-extern struct platform_device ux500_ske_keypad_device;
-
#endif
extern struct device * __init u8500_init_devices(void);
extern void __init ux500_init_irq(void);
-extern void __init ux500_init_late(void);
extern struct device *ux500_soc_device_init(const char *soc_id);
* sched_clock with higher rating then MTU since is always-on.
*
*/
-
- nmdk_timer_init(mtu_timer_base, IRQ_MTU0);
+ if (!of_have_populated_dt())
+ nmdk_timer_init(mtu_timer_base, IRQ_MTU0);
clksrc_dbx500_prcmu_init(prcmu_timer_base);
ux500_twd_init();
}
+++ /dev/null
-/*
- * Copyright (C) ST-Ericsson SA 2011
- *
- * Author: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
- * License terms: GNU General Public License (GPL) version 2
- */
-#include <linux/platform_device.h>
-#include <linux/usb/musb.h>
-#include <linux/dma-mapping.h>
-#include <linux/platform_data/usb-musb-ux500.h>
-#include <linux/platform_data/dma-ste-dma40.h>
-
-#include "db8500-regs.h"
-
-#define MUSB_DMA40_RX_CH { \
- .mode = STEDMA40_MODE_LOGICAL, \
- .dir = DMA_DEV_TO_MEM, \
- }
-
-#define MUSB_DMA40_TX_CH { \
- .mode = STEDMA40_MODE_LOGICAL, \
- .dir = DMA_MEM_TO_DEV, \
- }
-
-static struct stedma40_chan_cfg musb_dma_rx_ch[UX500_MUSB_DMA_NUM_RX_TX_CHANNELS]
- = {
- MUSB_DMA40_RX_CH,
- MUSB_DMA40_RX_CH,
- MUSB_DMA40_RX_CH,
- MUSB_DMA40_RX_CH,
- MUSB_DMA40_RX_CH,
- MUSB_DMA40_RX_CH,
- MUSB_DMA40_RX_CH,
- MUSB_DMA40_RX_CH
-};
-
-static struct stedma40_chan_cfg musb_dma_tx_ch[UX500_MUSB_DMA_NUM_RX_TX_CHANNELS]
- = {
- MUSB_DMA40_TX_CH,
- MUSB_DMA40_TX_CH,
- MUSB_DMA40_TX_CH,
- MUSB_DMA40_TX_CH,
- MUSB_DMA40_TX_CH,
- MUSB_DMA40_TX_CH,
- MUSB_DMA40_TX_CH,
- MUSB_DMA40_TX_CH,
-};
-
-static void *ux500_dma_rx_param_array[UX500_MUSB_DMA_NUM_RX_TX_CHANNELS] = {
- &musb_dma_rx_ch[0],
- &musb_dma_rx_ch[1],
- &musb_dma_rx_ch[2],
- &musb_dma_rx_ch[3],
- &musb_dma_rx_ch[4],
- &musb_dma_rx_ch[5],
- &musb_dma_rx_ch[6],
- &musb_dma_rx_ch[7]
-};
-
-static void *ux500_dma_tx_param_array[UX500_MUSB_DMA_NUM_RX_TX_CHANNELS] = {
- &musb_dma_tx_ch[0],
- &musb_dma_tx_ch[1],
- &musb_dma_tx_ch[2],
- &musb_dma_tx_ch[3],
- &musb_dma_tx_ch[4],
- &musb_dma_tx_ch[5],
- &musb_dma_tx_ch[6],
- &musb_dma_tx_ch[7]
-};
-
-static struct ux500_musb_board_data musb_board_data = {
- .dma_rx_param_array = ux500_dma_rx_param_array,
- .dma_tx_param_array = ux500_dma_tx_param_array,
- .dma_filter = stedma40_filter,
-};
-
-static struct musb_hdrc_platform_data musb_platform_data = {
- .mode = MUSB_OTG,
- .board_data = &musb_board_data,
-};
-
-static struct resource usb_resources[] = {
- [0] = {
- .name = "usb-mem",
- .flags = IORESOURCE_MEM,
- },
-
- [1] = {
- .name = "mc", /* hard-coded in musb */
- .flags = IORESOURCE_IRQ,
- },
-};
-
-struct platform_device ux500_musb_device = {
- .name = "musb-ux500",
- .id = 0,
- .dev = {
- .platform_data = &musb_platform_data,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .num_resources = ARRAY_SIZE(usb_resources),
- .resource = usb_resources,
-};
-
-static inline void ux500_usb_dma_update_rx_ch_config(int *dev_type)
-{
- u32 idx;
-
- for (idx = 0; idx < UX500_MUSB_DMA_NUM_RX_TX_CHANNELS; idx++)
- musb_dma_rx_ch[idx].dev_type = dev_type[idx];
-}
-
-static inline void ux500_usb_dma_update_tx_ch_config(int *dev_type)
-{
- u32 idx;
-
- for (idx = 0; idx < UX500_MUSB_DMA_NUM_RX_TX_CHANNELS; idx++)
- musb_dma_tx_ch[idx].dev_type = dev_type[idx];
-}
-
-void ux500_add_usb(struct device *parent, resource_size_t base, int irq,
- int *dma_rx_cfg, int *dma_tx_cfg)
-{
- ux500_musb_device.resource[0].start = base;
- ux500_musb_device.resource[0].end = base + SZ_64K - 1;
- ux500_musb_device.resource[1].start = irq;
- ux500_musb_device.resource[1].end = irq;
-
- ux500_usb_dma_update_rx_ch_config(dma_rx_cfg);
- ux500_usb_dma_update_tx_ch_config(dma_tx_cfg);
-
- ux500_musb_device.dev.parent = parent;
-
- platform_device_register(&ux500_musb_device);
-}
select ARM_AMBA
select ARM_GIC
select ARM_TIMER_SP804
- select CLKDEV_LOOKUP
select COMMON_CLK
select COMMON_CLK_VERSATILE
select CPU_V7
select GENERIC_CLOCKEVENTS
select HAVE_ARM_SCU if SMP
select HAVE_ARM_TWD if SMP
- select HAVE_CLK
select HAVE_PATA_PLATFORM
select HAVE_SMP
select ICST
/*
* Versatile Express V2M Motherboard Support
*/
-#include <linux/clocksource.h>
#include <linux/device.h>
#include <linux/amba/bus.h>
#include <linux/amba/mmci.h>
#include <linux/io.h>
-#include <linux/clocksource.h>
#include <linux/smp.h>
#include <linux/init.h>
#include <linux/of_address.h>
#include <linux/regulator/fixed.h>
#include <linux/regulator/machine.h>
#include <linux/vexpress.h>
-#include <linux/clk-provider.h>
#include <linux/clkdev.h>
#include <asm/mach-types.h>
pr_warning("vexpress: DT HBI (%x) is not matching "
"hardware (%x)!\n", dt_hbi, hbi);
}
-}
-
-static void __init v2m_dt_timer_init(void)
-{
- of_clk_init(NULL);
- clocksource_of_init();
-
- versatile_sched_clock_init(vexpress_get_24mhz_clock_base(),
- 24000000);
+ versatile_sched_clock_init(vexpress_get_24mhz_clock_base(), 24000000);
}
static const struct of_device_id v2m_dt_bus_match[] __initconst = {
.smp_init = smp_init_ops(vexpress_smp_init_ops),
.map_io = v2m_dt_map_io,
.init_early = v2m_dt_init_early,
- .init_time = v2m_dt_timer_init,
.init_machine = v2m_dt_init,
MACHINE_END
select CLKDEV_LOOKUP
select CLKSRC_OF
select GENERIC_CLOCKEVENTS
- select HAVE_CLK
select VT8500_TIMER
select PINCTRL
help
+++ /dev/null
-/* linux/arch/arm/mach-vt8500/dt_common.h
- *
- * Copyright (C) 2012 Tony Prisk <linux@prisktech.co.nz>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- */
-
-#ifndef __ARCH_ARM_MACH_VT8500_DT_COMMON_H
-#define __ARCH_ARM_MACH_VT8500_DT_COMMON_H
-
-#include <linux/of.h>
-
-/* defined in drivers/clk/clk-vt8500.c */
-void __init vtwm_clk_init(void __iomem *pmc_base);
-
-#endif
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
-#include <linux/clocksource.h>
#include <linux/io.h>
#include <linux/pm.h>
#include <linux/reboot.h>
#include <linux/of_irq.h>
#include <linux/of_platform.h>
-#include "common.h"
-
#define LEGACY_GPIO_BASE 0xD8110000
#define LEGACY_PMC_BASE 0xD8130000
else
pr_err("%s: PMC Hibernation register could not be remapped, not enabling power off!\n", __func__);
- vtwm_clk_init(pmc_base);
-
of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
}
.dt_compat = vt8500_dt_compat,
.map_io = vt8500_map_io,
.init_machine = vt8500_init,
- .init_time = clocksource_of_init,
.restart = vt8500_restart,
MACHINE_END
* published by the Free Software Foundation.
*/
+/*
+ * NOTE: Code in this file is not used on S3C64xx when booting with
+ * Device Tree support.
+ */
+
#include <linux/init.h>
#include <linux/module.h>
#include <linux/interrupt.h>
#include <linux/ioport.h>
#include <linux/serial_core.h>
#include <linux/platform_device.h>
+#include <linux/of.h>
#include <mach/hardware.h>
// do the correct init for cpu
- if (cpu == NULL)
+ if (cpu == NULL) {
+ /* Not needed when booting with device tree. */
+ if (of_have_populated_dt())
+ return 0;
panic("s3c_arch_init: NULL cpu\n");
+ }
ret = (cpu->init)();
if (ret != 0)
config BLK_DEV_HD
bool "Very old hard disk (MFM/RLL/IDE) driver"
depends on HAVE_IDE
- depends on !ARM || ARCH_RPC || ARCH_SHARK || BROKEN
+ depends on !ARM || ARCH_RPC || BROKEN
help
This is a very old hard disk driver that lacks the enhanced
functionality of the newer ones.
#include <linux/clk-provider.h>
#include <linux/clkdev.h>
#include <linux/clk/bcm2835.h>
-#include <linux/clk-provider.h>
#include <linux/of.h>
-static const struct of_device_id clk_match[] __initconst = {
- { .compatible = "fixed-clock", .data = of_fixed_clk_setup, },
- { }
-};
-
/*
* These are fixed clocks. They're probably not all root clocks and it may
* be possible to turn them on and off but until this is mapped out better
ret = clk_register_clkdev(clk, NULL, "20215000.uart");
if (ret)
pr_err("uart1_pclk alias not registered\n");
-
- of_clk_init(clk_match);
}
#include <linux/clk-provider.h>
#include <linux/io.h>
#include <linux/of.h>
-
-extern void __iomem *sregs_base;
+#include <linux/of_address.h>
#define HB_PLL_LOCK_500 0x20000000
#define HB_PLL_LOCK 0x10000000
const char *clk_name = node->name;
const char *parent_name;
struct clk_init_data init;
+ struct device_node *srnp;
int rc;
rc = of_property_read_u32(node, "reg", ®);
if (WARN_ON(!hb_clk))
return NULL;
- hb_clk->reg = sregs_base + reg;
+ /* Map system registers */
+ srnp = of_find_compatible_node(NULL, NULL, "calxeda,hb-sregs");
+ hb_clk->reg = of_iomap(srnp, 0);
+ BUG_ON(!hb_clk->reg);
+ hb_clk->reg += reg;
of_property_read_string(node, "clock-output-names", &clk_name);
*/
#define SRC_CR 0x00U
+#define SRC_CR_T0_ENSEL BIT(15)
+#define SRC_CR_T1_ENSEL BIT(17)
+#define SRC_CR_T2_ENSEL BIT(19)
+#define SRC_CR_T3_ENSEL BIT(21)
+#define SRC_CR_T4_ENSEL BIT(23)
+#define SRC_CR_T5_ENSEL BIT(25)
+#define SRC_CR_T6_ENSEL BIT(27)
+#define SRC_CR_T7_ENSEL BIT(29)
#define SRC_XTALCR 0x0CU
#define SRC_XTALCR_XTALTIMEN BIT(20)
#define SRC_XTALCR_SXTALDIS BIT(19)
/* Base address of the SRC */
static void __iomem *src_base;
+static int nomadik_clk_reboot_handler(struct notifier_block *this,
+ unsigned long code,
+ void *unused)
+{
+ u32 val;
+
+ /* The main chrystal need to be enabled for reboot to work */
+ val = readl(src_base + SRC_XTALCR);
+ val &= ~SRC_XTALCR_MXTALOVER;
+ val |= SRC_XTALCR_MXTALEN;
+ pr_crit("force-enabling MXTALO\n");
+ writel(val, src_base + SRC_XTALCR);
+ return NOTIFY_OK;
+}
+
+static struct notifier_block nomadik_clk_reboot_notifier = {
+ .notifier_call = nomadik_clk_reboot_handler,
+};
+
+static const struct of_device_id nomadik_src_match[] __initconst = {
+ { .compatible = "stericsson,nomadik-src" },
+ { /* sentinel */ }
+};
+
+static void __init nomadik_src_init(void)
+{
+ struct device_node *np;
+ u32 val;
+
+ np = of_find_matching_node(NULL, nomadik_src_match);
+ if (!np) {
+ pr_crit("no matching node for SRC, aborting clock init\n");
+ return;
+ }
+ src_base = of_iomap(np, 0);
+ if (!src_base) {
+ pr_err("%s: must have src parent node with REGS (%s)\n",
+ __func__, np->name);
+ return;
+ }
+
+ /* Set all timers to use the 2.4 MHz TIMCLK */
+ val = readl(src_base + SRC_CR);
+ val |= SRC_CR_T0_ENSEL;
+ val |= SRC_CR_T1_ENSEL;
+ val |= SRC_CR_T2_ENSEL;
+ val |= SRC_CR_T3_ENSEL;
+ val |= SRC_CR_T4_ENSEL;
+ val |= SRC_CR_T5_ENSEL;
+ val |= SRC_CR_T6_ENSEL;
+ val |= SRC_CR_T7_ENSEL;
+ writel(val, src_base + SRC_CR);
+
+ val = readl(src_base + SRC_XTALCR);
+ pr_info("SXTALO is %s\n",
+ (val & SRC_XTALCR_SXTALDIS) ? "disabled" : "enabled");
+ pr_info("MXTAL is %s\n",
+ (val & SRC_XTALCR_MXTALSTAT) ? "enabled" : "disabled");
+ if (of_property_read_bool(np, "disable-sxtalo")) {
+ /* The machine uses an external oscillator circuit */
+ val |= SRC_XTALCR_SXTALDIS;
+ pr_info("disabling SXTALO\n");
+ }
+ if (of_property_read_bool(np, "disable-mxtalo")) {
+ /* Disable this too: also run by external oscillator */
+ val |= SRC_XTALCR_MXTALOVER;
+ val &= ~SRC_XTALCR_MXTALEN;
+ pr_info("disabling MXTALO\n");
+ }
+ writel(val, src_base + SRC_XTALCR);
+ register_reboot_notifier(&nomadik_clk_reboot_notifier);
+}
+
/**
* struct clk_pll1 - Nomadik PLL1 clock
* @hw: corresponding clock hardware entry
const char *parent_name;
u32 pll_id;
+ if (!src_base)
+ nomadik_src_init();
+
if (of_property_read_u32(np, "pll-id", &pll_id)) {
pr_err("%s: PLL \"%s\" missing pll-id property\n",
__func__, clk_name);
if (!IS_ERR(clk))
of_clk_add_provider(np, of_clk_src_simple_get, clk);
}
+CLK_OF_DECLARE(nomadik_pll_clk,
+ "st,nomadik-pll-clock", of_nomadik_pll_setup);
static void __init of_nomadik_hclk_setup(struct device_node *np)
{
const char *clk_name = np->name;
const char *parent_name;
+ if (!src_base)
+ nomadik_src_init();
+
parent_name = of_clk_get_parent_name(np, 0);
/*
* The HCLK divides PLL1 with 1 (passthru), 2, 3 or 4.
if (!IS_ERR(clk))
of_clk_add_provider(np, of_clk_src_simple_get, clk);
}
+CLK_OF_DECLARE(nomadik_hclk_clk,
+ "st,nomadik-hclk-clock", of_nomadik_hclk_setup);
static void __init of_nomadik_src_clk_setup(struct device_node *np)
{
const char *parent_name;
u32 clk_id;
+ if (!src_base)
+ nomadik_src_init();
+
if (of_property_read_u32(np, "clock-id", &clk_id)) {
pr_err("%s: SRC clock \"%s\" missing clock-id property\n",
__func__, clk_name);
if (!IS_ERR(clk))
of_clk_add_provider(np, of_clk_src_simple_get, clk);
}
-
-static const struct of_device_id nomadik_src_match[] __initconst = {
- { .compatible = "stericsson,nomadik-src" },
- { /* sentinel */ }
-};
-
-static const struct of_device_id nomadik_src_clk_match[] __initconst = {
- {
- .compatible = "fixed-clock",
- .data = of_fixed_clk_setup,
- },
- {
- .compatible = "fixed-factor-clock",
- .data = of_fixed_factor_clk_setup,
- },
- {
- .compatible = "st,nomadik-pll-clock",
- .data = of_nomadik_pll_setup,
- },
- {
- .compatible = "st,nomadik-hclk-clock",
- .data = of_nomadik_hclk_setup,
- },
- {
- .compatible = "st,nomadik-src-clock",
- .data = of_nomadik_src_clk_setup,
- },
- { /* sentinel */ }
-};
-
-static int nomadik_clk_reboot_handler(struct notifier_block *this,
- unsigned long code,
- void *unused)
-{
- u32 val;
-
- /* The main chrystal need to be enabled for reboot to work */
- val = readl(src_base + SRC_XTALCR);
- val &= ~SRC_XTALCR_MXTALOVER;
- val |= SRC_XTALCR_MXTALEN;
- pr_crit("force-enabling MXTALO\n");
- writel(val, src_base + SRC_XTALCR);
- return NOTIFY_OK;
-}
-
-static struct notifier_block nomadik_clk_reboot_notifier = {
- .notifier_call = nomadik_clk_reboot_handler,
-};
-
-void __init nomadik_clk_init(void)
-{
- struct device_node *np;
- u32 val;
-
- np = of_find_matching_node(NULL, nomadik_src_match);
- if (!np) {
- pr_crit("no matching node for SRC, aborting clock init\n");
- return;
- }
- src_base = of_iomap(np, 0);
- if (!src_base) {
- pr_err("%s: must have src parent node with REGS (%s)\n",
- __func__, np->name);
- return;
- }
- val = readl(src_base + SRC_XTALCR);
- pr_info("SXTALO is %s\n",
- (val & SRC_XTALCR_SXTALDIS) ? "disabled" : "enabled");
- pr_info("MXTAL is %s\n",
- (val & SRC_XTALCR_MXTALSTAT) ? "enabled" : "disabled");
- if (of_property_read_bool(np, "disable-sxtalo")) {
- /* The machine uses an external oscillator circuit */
- val |= SRC_XTALCR_SXTALDIS;
- pr_info("disabling SXTALO\n");
- }
- if (of_property_read_bool(np, "disable-mxtalo")) {
- /* Disable this too: also run by external oscillator */
- val |= SRC_XTALCR_MXTALOVER;
- val &= ~SRC_XTALCR_MXTALEN;
- pr_info("disabling MXTALO\n");
- }
- writel(val, src_base + SRC_XTALCR);
- register_reboot_notifier(&nomadik_clk_reboot_notifier);
-
- of_clk_init(nomadik_src_clk_match);
-}
+CLK_OF_DECLARE(nomadik_src_clk,
+ "st,nomadik-src-clock", of_nomadik_src_clk_setup);
},
};
-static struct of_device_id clkc_ids[] = {
- { .compatible = "sirf,prima2-clkc" },
- {},
-};
-
-static struct of_device_id rsc_ids[] = {
- { .compatible = "sirf,prima2-rsc" },
- {},
-};
-
enum prima2_clk_index {
/* 0 1 2 3 4 5 6 7 8 9 */
rtc, osc, pll1, pll2, pll3, mem, sys, security, dsp, gps,
static struct clk *prima2_clks[maxclk];
static struct clk_onecell_data clk_data;
-void __init sirfsoc_of_clk_init(void)
+static void __init sirfsoc_clk_init(struct device_node *np)
{
- struct device_node *np;
+ struct device_node *rscnp;
int i;
- np = of_find_matching_node(NULL, rsc_ids);
- if (!np)
- panic("unable to find compatible rsc node in dtb\n");
-
- sirfsoc_rsc_vbase = of_iomap(np, 0);
+ rscnp = of_find_compatible_node(NULL, NULL, "sirf,prima2-rsc");
+ sirfsoc_rsc_vbase = of_iomap(rscnp, 0);
if (!sirfsoc_rsc_vbase)
panic("unable to map rsc registers\n");
-
- of_node_put(np);
-
- np = of_find_matching_node(NULL, clkc_ids);
- if (!np)
- return;
+ of_node_put(rscnp);
sirfsoc_clk_vbase = of_iomap(np, 0);
if (!sirfsoc_clk_vbase)
of_clk_add_provider(np, of_clk_src_onecell_get, &clk_data);
}
+CLK_OF_DECLARE(sirfsoc_clk, "sirf,prima2-clkc", sirfsoc_clk_init);
#include <linux/io.h>
#include <linux/of.h>
+#include <linux/of_address.h>
#include <linux/slab.h>
#include <linux/bitops.h>
#include <linux/clkdev.h>
#include <linux/clk-provider.h>
+#define LEGACY_PMC_BASE 0xD8130000
+
/* All clocks share the same lock as none can be changed concurrently */
static DEFINE_SPINLOCK(_lock);
static void __iomem *pmc_base;
+static __init void vtwm_set_pmc_base(void)
+{
+ struct device_node *np =
+ of_find_compatible_node(NULL, NULL, "via,vt8500-pmc");
+
+ if (np)
+ pmc_base = of_iomap(np, 0);
+ else
+ pmc_base = ioremap(LEGACY_PMC_BASE, 0x1000);
+ of_node_put(np);
+
+ if (!pmc_base)
+ pr_err("%s:of_iomap(pmc) failed\n", __func__);
+}
+
#define to_clk_device(_hw) container_of(_hw, struct clk_device, hw)
#define VT8500_PMC_BUSY_MASK 0x18
int rc;
int clk_init_flags = 0;
+ if (!pmc_base)
+ vtwm_set_pmc_base();
+
dev_clk = kzalloc(sizeof(*dev_clk), GFP_KERNEL);
if (WARN_ON(!dev_clk))
return;
struct clk_init_data init;
int rc;
+ if (!pmc_base)
+ vtwm_set_pmc_base();
+
rc = of_property_read_u32(node, "reg", ®);
if (WARN_ON(rc))
return;
vtwm_pll_clk_init(node, PLL_TYPE_WM8850);
}
CLK_OF_DECLARE(wm8850_pll, "wm,wm8850-pll-clock", wm8850_pll_init);
-
-void __init vtwm_clk_init(void __iomem *base)
-{
- if (!base)
- return;
-
- pmc_base = base;
-
- of_clk_init(NULL);
-}
#include <linux/clk.h>
#include <linux/clk/mxs.h>
#include <linux/clkdev.h>
+#include <linux/clk-provider.h>
#include <linux/err.h>
#include <linux/init.h>
#include <linux/io.h>
cpu, hbus, xbus, emi, uart,
};
-int __init mx23_clocks_init(void)
+static void __init mx23_clocks_init(struct device_node *np)
{
- struct device_node *np;
+ struct device_node *dcnp;
u32 i;
- np = of_find_compatible_node(NULL, NULL, "fsl,imx23-digctl");
- digctrl = of_iomap(np, 0);
+ dcnp = of_find_compatible_node(NULL, NULL, "fsl,imx23-digctl");
+ digctrl = of_iomap(dcnp, 0);
WARN_ON(!digctrl);
+ of_node_put(dcnp);
- np = of_find_compatible_node(NULL, NULL, "fsl,imx23-clkctrl");
clkctrl = of_iomap(np, 0);
WARN_ON(!clkctrl);
if (IS_ERR(clks[i])) {
pr_err("i.MX23 clk %d: register failed with %ld\n",
i, PTR_ERR(clks[i]));
- return PTR_ERR(clks[i]);
+ return;
}
clk_data.clks = clks;
for (i = 0; i < ARRAY_SIZE(clks_init_on); i++)
clk_prepare_enable(clks[clks_init_on[i]]);
- return 0;
}
+CLK_OF_DECLARE(imx23_clkctrl, "fsl,imx23-clkctrl", mx23_clocks_init);
#include <linux/clk.h>
#include <linux/clk/mxs.h>
#include <linux/clkdev.h>
+#include <linux/clk-provider.h>
#include <linux/err.h>
#include <linux/init.h>
#include <linux/io.h>
cpu, hbus, xbus, emi, uart,
};
-int __init mx28_clocks_init(void)
+static void __init mx28_clocks_init(struct device_node *np)
{
- struct device_node *np;
+ struct device_node *dcnp;
u32 i;
- np = of_find_compatible_node(NULL, NULL, "fsl,imx28-digctl");
- digctrl = of_iomap(np, 0);
+ dcnp = of_find_compatible_node(NULL, NULL, "fsl,imx28-digctl");
+ digctrl = of_iomap(dcnp, 0);
WARN_ON(!digctrl);
+ of_node_put(dcnp);
- np = of_find_compatible_node(NULL, NULL, "fsl,imx28-clkctrl");
clkctrl = of_iomap(np, 0);
WARN_ON(!clkctrl);
if (IS_ERR(clks[i])) {
pr_err("i.MX28 clk %d: register failed with %ld\n",
i, PTR_ERR(clks[i]));
- return PTR_ERR(clks[i]);
+ return;
}
clk_data.clks = clks;
for (i = 0; i < ARRAY_SIZE(clks_init_on); i++)
clk_prepare_enable(clks[clks_init_on[i]]);
-
- return 0;
}
+CLK_OF_DECLARE(imx28_clkctrl, "fsl,imx28-clkctrl", mx28_clocks_init);
#include <linux/clk-provider.h>
#include <linux/clkdev.h>
-#include <linux/clk/sunxi.h>
#include <linux/of.h>
#include <linux/of_address.h>
}
}
-void __init sunxi_init_clocks(void)
+static void __init sunxi_init_clocks(struct device_node *np)
{
- /* Register all the simple and basic clocks on DT */
- of_clk_init(NULL);
-
/* Register factor clocks */
of_sunxi_table_clock_setup(clk_factors_match, sunxi_factors_clk_setup);
/* Register gate clocks */
of_sunxi_table_clock_setup(clk_gates_match, sunxi_gates_clk_setup);
}
+CLK_OF_DECLARE(sun4i_a10_clk_init, "allwinner,sun4i-a10", sunxi_init_clocks);
+CLK_OF_DECLARE(sun5i_a10s_clk_init, "allwinner,sun5i-a10s", sunxi_init_clocks);
+CLK_OF_DECLARE(sun5i_a13_clk_init, "allwinner,sun5i-a13", sunxi_init_clocks);
+CLK_OF_DECLARE(sun6i_a31_clk_init, "allwinner,sun6i-a31", sunxi_init_clocks);
+CLK_OF_DECLARE(sun7i_a20_clk_init, "allwinner,sun7i-a20", sunxi_init_clocks);
obj-y += clk-sysctrl.o
# Clock definitions
+obj-y += u8500_of_clk.o
obj-y += u8500_clk.o
obj-y += u9540_clk.o
obj-y += u8540_clk.o
--- /dev/null
+/*
+ * Clock definitions for u8500 platform.
+ *
+ * Copyright (C) 2012 ST-Ericsson SA
+ * Author: Ulf Hansson <ulf.hansson@linaro.org>
+ *
+ * License terms: GNU General Public License (GPL) version 2
+ */
+
+#include <linux/of.h>
+#include <linux/clk.h>
+#include <linux/clkdev.h>
+#include <linux/clk-provider.h>
+#include <linux/mfd/dbx500-prcmu.h>
+#include <linux/platform_data/clk-ux500.h>
+#include "clk.h"
+
+#define PRCC_NUM_PERIPH_CLUSTERS 6
+#define PRCC_PERIPHS_PER_CLUSTER 32
+
+static struct clk *prcmu_clk[PRCMU_NUM_CLKS];
+static struct clk *prcc_pclk[(PRCC_NUM_PERIPH_CLUSTERS + 1) * PRCC_PERIPHS_PER_CLUSTER];
+static struct clk *prcc_kclk[(PRCC_NUM_PERIPH_CLUSTERS + 1) * PRCC_PERIPHS_PER_CLUSTER];
+
+#define PRCC_SHOW(clk, base, bit) \
+ clk[(base * PRCC_PERIPHS_PER_CLUSTER) + bit]
+#define PRCC_PCLK_STORE(clk, base, bit) \
+ prcc_pclk[(base * PRCC_PERIPHS_PER_CLUSTER) + bit] = clk
+#define PRCC_KCLK_STORE(clk, base, bit) \
+ prcc_kclk[(base * PRCC_PERIPHS_PER_CLUSTER) + bit] = clk
+
+struct clk *ux500_twocell_get(struct of_phandle_args *clkspec, void *data)
+{
+ struct clk **clk_data = data;
+ unsigned int base, bit;
+
+ if (clkspec->args_count != 2)
+ return ERR_PTR(-EINVAL);
+
+ base = clkspec->args[0];
+ bit = clkspec->args[1];
+
+ if (base != 1 && base != 2 && base != 3 && base != 5 && base != 6) {
+ pr_err("%s: invalid PRCC base %d\n", __func__, base);
+ return ERR_PTR(-EINVAL);
+ }
+
+ return PRCC_SHOW(clk_data, base, bit);
+}
+
+static const struct of_device_id u8500_clk_of_match[] = {
+ { .compatible = "stericsson,u8500-clks", },
+ { },
+};
+
+void u8500_of_clk_init(u32 clkrst1_base, u32 clkrst2_base, u32 clkrst3_base,
+ u32 clkrst5_base, u32 clkrst6_base)
+{
+ struct prcmu_fw_version *fw_version;
+ struct device_node *np = NULL;
+ struct device_node *child = NULL;
+ const char *sgaclk_parent = NULL;
+ struct clk *clk, *rtc_clk, *twd_clk;
+
+ if (of_have_populated_dt())
+ np = of_find_matching_node(NULL, u8500_clk_of_match);
+ if (!np) {
+ pr_err("Either DT or U8500 Clock node not found\n");
+ return;
+ }
+
+ /* Clock sources */
+ clk = clk_reg_prcmu_gate("soc0_pll", NULL, PRCMU_PLLSOC0,
+ CLK_IS_ROOT|CLK_IGNORE_UNUSED);
+ prcmu_clk[PRCMU_PLLSOC0] = clk;
+
+ clk = clk_reg_prcmu_gate("soc1_pll", NULL, PRCMU_PLLSOC1,
+ CLK_IS_ROOT|CLK_IGNORE_UNUSED);
+ prcmu_clk[PRCMU_PLLSOC1] = clk;
+
+ clk = clk_reg_prcmu_gate("ddr_pll", NULL, PRCMU_PLLDDR,
+ CLK_IS_ROOT|CLK_IGNORE_UNUSED);
+ prcmu_clk[PRCMU_PLLDDR] = clk;
+
+ /* FIXME: Add sys, ulp and int clocks here. */
+
+ rtc_clk = clk_register_fixed_rate(NULL, "rtc32k", "NULL",
+ CLK_IS_ROOT|CLK_IGNORE_UNUSED,
+ 32768);
+
+ /* PRCMU clocks */
+ fw_version = prcmu_get_fw_version();
+ if (fw_version != NULL) {
+ switch (fw_version->project) {
+ case PRCMU_FW_PROJECT_U8500_C2:
+ case PRCMU_FW_PROJECT_U8520:
+ case PRCMU_FW_PROJECT_U8420:
+ sgaclk_parent = "soc0_pll";
+ break;
+ default:
+ break;
+ }
+ }
+
+ if (sgaclk_parent)
+ clk = clk_reg_prcmu_gate("sgclk", sgaclk_parent,
+ PRCMU_SGACLK, 0);
+ else
+ clk = clk_reg_prcmu_gate("sgclk", NULL,
+ PRCMU_SGACLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_SGACLK] = clk;
+
+ clk = clk_reg_prcmu_gate("uartclk", NULL, PRCMU_UARTCLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_UARTCLK] = clk;
+
+ clk = clk_reg_prcmu_gate("msp02clk", NULL, PRCMU_MSP02CLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_MSP02CLK] = clk;
+
+ clk = clk_reg_prcmu_gate("msp1clk", NULL, PRCMU_MSP1CLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_MSP1CLK] = clk;
+
+ clk = clk_reg_prcmu_gate("i2cclk", NULL, PRCMU_I2CCLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_I2CCLK] = clk;
+
+ clk = clk_reg_prcmu_gate("slimclk", NULL, PRCMU_SLIMCLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_SLIMCLK] = clk;
+
+ clk = clk_reg_prcmu_gate("per1clk", NULL, PRCMU_PER1CLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_PER1CLK] = clk;
+
+ clk = clk_reg_prcmu_gate("per2clk", NULL, PRCMU_PER2CLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_PER2CLK] = clk;
+
+ clk = clk_reg_prcmu_gate("per3clk", NULL, PRCMU_PER3CLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_PER3CLK] = clk;
+
+ clk = clk_reg_prcmu_gate("per5clk", NULL, PRCMU_PER5CLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_PER5CLK] = clk;
+
+ clk = clk_reg_prcmu_gate("per6clk", NULL, PRCMU_PER6CLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_PER6CLK] = clk;
+
+ clk = clk_reg_prcmu_gate("per7clk", NULL, PRCMU_PER7CLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_PER7CLK] = clk;
+
+ clk = clk_reg_prcmu_scalable("lcdclk", NULL, PRCMU_LCDCLK, 0,
+ CLK_IS_ROOT|CLK_SET_RATE_GATE);
+ prcmu_clk[PRCMU_LCDCLK] = clk;
+
+ clk = clk_reg_prcmu_opp_gate("bmlclk", NULL, PRCMU_BMLCLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_BMLCLK] = clk;
+
+ clk = clk_reg_prcmu_scalable("hsitxclk", NULL, PRCMU_HSITXCLK, 0,
+ CLK_IS_ROOT|CLK_SET_RATE_GATE);
+ prcmu_clk[PRCMU_HSITXCLK] = clk;
+
+ clk = clk_reg_prcmu_scalable("hsirxclk", NULL, PRCMU_HSIRXCLK, 0,
+ CLK_IS_ROOT|CLK_SET_RATE_GATE);
+ prcmu_clk[PRCMU_HSIRXCLK] = clk;
+
+ clk = clk_reg_prcmu_scalable("hdmiclk", NULL, PRCMU_HDMICLK, 0,
+ CLK_IS_ROOT|CLK_SET_RATE_GATE);
+ prcmu_clk[PRCMU_HDMICLK] = clk;
+
+ clk = clk_reg_prcmu_gate("apeatclk", NULL, PRCMU_APEATCLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_APEATCLK] = clk;
+
+ clk = clk_reg_prcmu_gate("apetraceclk", NULL, PRCMU_APETRACECLK,
+ CLK_IS_ROOT);
+ prcmu_clk[PRCMU_APETRACECLK] = clk;
+
+ clk = clk_reg_prcmu_gate("mcdeclk", NULL, PRCMU_MCDECLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_MCDECLK] = clk;
+
+ clk = clk_reg_prcmu_opp_gate("ipi2cclk", NULL, PRCMU_IPI2CCLK,
+ CLK_IS_ROOT);
+ prcmu_clk[PRCMU_IPI2CCLK] = clk;
+
+ clk = clk_reg_prcmu_gate("dsialtclk", NULL, PRCMU_DSIALTCLK,
+ CLK_IS_ROOT);
+ prcmu_clk[PRCMU_DSIALTCLK] = clk;
+
+ clk = clk_reg_prcmu_gate("dmaclk", NULL, PRCMU_DMACLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_DMACLK] = clk;
+
+ clk = clk_reg_prcmu_gate("b2r2clk", NULL, PRCMU_B2R2CLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_B2R2CLK] = clk;
+
+ clk = clk_reg_prcmu_scalable("tvclk", NULL, PRCMU_TVCLK, 0,
+ CLK_IS_ROOT|CLK_SET_RATE_GATE);
+ prcmu_clk[PRCMU_TVCLK] = clk;
+
+ clk = clk_reg_prcmu_gate("sspclk", NULL, PRCMU_SSPCLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_SSPCLK] = clk;
+
+ clk = clk_reg_prcmu_gate("rngclk", NULL, PRCMU_RNGCLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_RNGCLK] = clk;
+
+ clk = clk_reg_prcmu_gate("uiccclk", NULL, PRCMU_UICCCLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_UICCCLK] = clk;
+
+ clk = clk_reg_prcmu_gate("timclk", NULL, PRCMU_TIMCLK, CLK_IS_ROOT);
+ prcmu_clk[PRCMU_TIMCLK] = clk;
+
+ clk = clk_reg_prcmu_opp_volt_scalable("sdmmcclk", NULL, PRCMU_SDMMCCLK,
+ 100000000,
+ CLK_IS_ROOT|CLK_SET_RATE_GATE);
+ prcmu_clk[PRCMU_SDMMCCLK] = clk;
+
+ clk = clk_reg_prcmu_scalable("dsi_pll", "hdmiclk",
+ PRCMU_PLLDSI, 0, CLK_SET_RATE_GATE);
+ prcmu_clk[PRCMU_PLLDSI] = clk;
+
+ clk = clk_reg_prcmu_scalable("dsi0clk", "dsi_pll",
+ PRCMU_DSI0CLK, 0, CLK_SET_RATE_GATE);
+ prcmu_clk[PRCMU_DSI0CLK] = clk;
+
+ clk = clk_reg_prcmu_scalable("dsi1clk", "dsi_pll",
+ PRCMU_DSI1CLK, 0, CLK_SET_RATE_GATE);
+ prcmu_clk[PRCMU_DSI1CLK] = clk;
+
+ clk = clk_reg_prcmu_scalable("dsi0escclk", "tvclk",
+ PRCMU_DSI0ESCCLK, 0, CLK_SET_RATE_GATE);
+ prcmu_clk[PRCMU_DSI0ESCCLK] = clk;
+
+ clk = clk_reg_prcmu_scalable("dsi1escclk", "tvclk",
+ PRCMU_DSI1ESCCLK, 0, CLK_SET_RATE_GATE);
+ prcmu_clk[PRCMU_DSI1ESCCLK] = clk;
+
+ clk = clk_reg_prcmu_scalable("dsi2escclk", "tvclk",
+ PRCMU_DSI2ESCCLK, 0, CLK_SET_RATE_GATE);
+ prcmu_clk[PRCMU_DSI2ESCCLK] = clk;
+
+ clk = clk_reg_prcmu_scalable_rate("armss", NULL,
+ PRCMU_ARMSS, 0, CLK_IS_ROOT|CLK_IGNORE_UNUSED);
+ prcmu_clk[PRCMU_ARMSS] = clk;
+
+ twd_clk = clk_register_fixed_factor(NULL, "smp_twd", "armss",
+ CLK_IGNORE_UNUSED, 1, 2);
+
+ /*
+ * FIXME: Add special handled PRCMU clocks here:
+ * 1. clkout0yuv, use PRCMU as parent + need regulator + pinctrl.
+ * 2. ab9540_clkout1yuv, see clkout0yuv
+ */
+
+ /* PRCC P-clocks */
+ clk = clk_reg_prcc_pclk("p1_pclk0", "per1clk", clkrst1_base,
+ BIT(0), 0);
+ PRCC_PCLK_STORE(clk, 1, 0);
+
+ clk = clk_reg_prcc_pclk("p1_pclk1", "per1clk", clkrst1_base,
+ BIT(1), 0);
+ PRCC_PCLK_STORE(clk, 1, 1);
+
+ clk = clk_reg_prcc_pclk("p1_pclk2", "per1clk", clkrst1_base,
+ BIT(2), 0);
+ PRCC_PCLK_STORE(clk, 1, 2);
+
+ clk = clk_reg_prcc_pclk("p1_pclk3", "per1clk", clkrst1_base,
+ BIT(3), 0);
+ PRCC_PCLK_STORE(clk, 1, 3);
+
+ clk = clk_reg_prcc_pclk("p1_pclk4", "per1clk", clkrst1_base,
+ BIT(4), 0);
+ PRCC_PCLK_STORE(clk, 1, 4);
+
+ clk = clk_reg_prcc_pclk("p1_pclk5", "per1clk", clkrst1_base,
+ BIT(5), 0);
+ PRCC_PCLK_STORE(clk, 1, 5);
+
+ clk = clk_reg_prcc_pclk("p1_pclk6", "per1clk", clkrst1_base,
+ BIT(6), 0);
+ PRCC_PCLK_STORE(clk, 1, 6);
+
+ clk = clk_reg_prcc_pclk("p1_pclk7", "per1clk", clkrst1_base,
+ BIT(7), 0);
+ PRCC_PCLK_STORE(clk, 1, 7);
+
+ clk = clk_reg_prcc_pclk("p1_pclk8", "per1clk", clkrst1_base,
+ BIT(8), 0);
+ PRCC_PCLK_STORE(clk, 1, 8);
+
+ clk = clk_reg_prcc_pclk("p1_pclk9", "per1clk", clkrst1_base,
+ BIT(9), 0);
+ PRCC_PCLK_STORE(clk, 1, 9);
+
+ clk = clk_reg_prcc_pclk("p1_pclk10", "per1clk", clkrst1_base,
+ BIT(10), 0);
+ PRCC_PCLK_STORE(clk, 1, 10);
+
+ clk = clk_reg_prcc_pclk("p1_pclk11", "per1clk", clkrst1_base,
+ BIT(11), 0);
+ PRCC_PCLK_STORE(clk, 1, 11);
+
+ clk = clk_reg_prcc_pclk("p2_pclk0", "per2clk", clkrst2_base,
+ BIT(0), 0);
+ PRCC_PCLK_STORE(clk, 2, 0);
+
+ clk = clk_reg_prcc_pclk("p2_pclk1", "per2clk", clkrst2_base,
+ BIT(1), 0);
+ PRCC_PCLK_STORE(clk, 2, 1);
+
+ clk = clk_reg_prcc_pclk("p2_pclk2", "per2clk", clkrst2_base,
+ BIT(2), 0);
+ PRCC_PCLK_STORE(clk, 2, 2);
+
+ clk = clk_reg_prcc_pclk("p2_pclk3", "per2clk", clkrst2_base,
+ BIT(3), 0);
+ PRCC_PCLK_STORE(clk, 2, 3);
+
+ clk = clk_reg_prcc_pclk("p2_pclk4", "per2clk", clkrst2_base,
+ BIT(4), 0);
+ PRCC_PCLK_STORE(clk, 2, 4);
+
+ clk = clk_reg_prcc_pclk("p2_pclk5", "per2clk", clkrst2_base,
+ BIT(5), 0);
+ PRCC_PCLK_STORE(clk, 2, 5);
+
+ clk = clk_reg_prcc_pclk("p2_pclk6", "per2clk", clkrst2_base,
+ BIT(6), 0);
+ PRCC_PCLK_STORE(clk, 2, 6);
+
+ clk = clk_reg_prcc_pclk("p2_pclk7", "per2clk", clkrst2_base,
+ BIT(7), 0);
+ PRCC_PCLK_STORE(clk, 2, 7);
+
+ clk = clk_reg_prcc_pclk("p2_pclk8", "per2clk", clkrst2_base,
+ BIT(8), 0);
+ PRCC_PCLK_STORE(clk, 2, 8);
+
+ clk = clk_reg_prcc_pclk("p2_pclk9", "per2clk", clkrst2_base,
+ BIT(9), 0);
+ PRCC_PCLK_STORE(clk, 2, 9);
+
+ clk = clk_reg_prcc_pclk("p2_pclk10", "per2clk", clkrst2_base,
+ BIT(10), 0);
+ PRCC_PCLK_STORE(clk, 2, 10);
+
+ clk = clk_reg_prcc_pclk("p2_pclk11", "per2clk", clkrst2_base,
+ BIT(11), 0);
+ PRCC_PCLK_STORE(clk, 2, 1);
+
+ clk = clk_reg_prcc_pclk("p2_pclk12", "per2clk", clkrst2_base,
+ BIT(12), 0);
+ PRCC_PCLK_STORE(clk, 2, 12);
+
+ clk = clk_reg_prcc_pclk("p3_pclk0", "per3clk", clkrst3_base,
+ BIT(0), 0);
+ PRCC_PCLK_STORE(clk, 3, 0);
+
+ clk = clk_reg_prcc_pclk("p3_pclk1", "per3clk", clkrst3_base,
+ BIT(1), 0);
+ PRCC_PCLK_STORE(clk, 3, 1);
+
+ clk = clk_reg_prcc_pclk("p3_pclk2", "per3clk", clkrst3_base,
+ BIT(2), 0);
+ PRCC_PCLK_STORE(clk, 3, 2);
+
+ clk = clk_reg_prcc_pclk("p3_pclk3", "per3clk", clkrst3_base,
+ BIT(3), 0);
+ PRCC_PCLK_STORE(clk, 3, 3);
+
+ clk = clk_reg_prcc_pclk("p3_pclk4", "per3clk", clkrst3_base,
+ BIT(4), 0);
+ PRCC_PCLK_STORE(clk, 3, 4);
+
+ clk = clk_reg_prcc_pclk("p3_pclk5", "per3clk", clkrst3_base,
+ BIT(5), 0);
+ PRCC_PCLK_STORE(clk, 3, 5);
+
+ clk = clk_reg_prcc_pclk("p3_pclk6", "per3clk", clkrst3_base,
+ BIT(6), 0);
+ PRCC_PCLK_STORE(clk, 3, 6);
+
+ clk = clk_reg_prcc_pclk("p3_pclk7", "per3clk", clkrst3_base,
+ BIT(7), 0);
+ PRCC_PCLK_STORE(clk, 3, 7);
+
+ clk = clk_reg_prcc_pclk("p3_pclk8", "per3clk", clkrst3_base,
+ BIT(8), 0);
+ PRCC_PCLK_STORE(clk, 3, 8);
+
+ clk = clk_reg_prcc_pclk("p5_pclk0", "per5clk", clkrst5_base,
+ BIT(0), 0);
+ PRCC_PCLK_STORE(clk, 5, 0);
+
+ clk = clk_reg_prcc_pclk("p5_pclk1", "per5clk", clkrst5_base,
+ BIT(1), 0);
+ PRCC_PCLK_STORE(clk, 5, 1);
+
+ clk = clk_reg_prcc_pclk("p6_pclk0", "per6clk", clkrst6_base,
+ BIT(0), 0);
+ PRCC_PCLK_STORE(clk, 6, 0);
+
+ clk = clk_reg_prcc_pclk("p6_pclk1", "per6clk", clkrst6_base,
+ BIT(1), 0);
+ PRCC_PCLK_STORE(clk, 6, 1);
+
+ clk = clk_reg_prcc_pclk("p6_pclk2", "per6clk", clkrst6_base,
+ BIT(2), 0);
+ PRCC_PCLK_STORE(clk, 6, 2);
+
+ clk = clk_reg_prcc_pclk("p6_pclk3", "per6clk", clkrst6_base,
+ BIT(3), 0);
+ PRCC_PCLK_STORE(clk, 6, 3);
+
+ clk = clk_reg_prcc_pclk("p6_pclk4", "per6clk", clkrst6_base,
+ BIT(4), 0);
+ PRCC_PCLK_STORE(clk, 6, 4);
+
+ clk = clk_reg_prcc_pclk("p6_pclk5", "per6clk", clkrst6_base,
+ BIT(5), 0);
+ PRCC_PCLK_STORE(clk, 6, 5);
+
+ clk = clk_reg_prcc_pclk("p6_pclk6", "per6clk", clkrst6_base,
+ BIT(6), 0);
+ PRCC_PCLK_STORE(clk, 6, 6);
+
+ clk = clk_reg_prcc_pclk("p6_pclk7", "per6clk", clkrst6_base,
+ BIT(7), 0);
+ PRCC_PCLK_STORE(clk, 6, 7);
+
+ /* PRCC K-clocks
+ *
+ * FIXME: Some drivers requires PERPIH[n| to be automatically enabled
+ * by enabling just the K-clock, even if it is not a valid parent to
+ * the K-clock. Until drivers get fixed we might need some kind of
+ * "parent muxed join".
+ */
+
+ /* Periph1 */
+ clk = clk_reg_prcc_kclk("p1_uart0_kclk", "uartclk",
+ clkrst1_base, BIT(0), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 1, 0);
+
+ clk = clk_reg_prcc_kclk("p1_uart1_kclk", "uartclk",
+ clkrst1_base, BIT(1), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 1, 1);
+
+ clk = clk_reg_prcc_kclk("p1_i2c1_kclk", "i2cclk",
+ clkrst1_base, BIT(2), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 1, 2);
+
+ clk = clk_reg_prcc_kclk("p1_msp0_kclk", "msp02clk",
+ clkrst1_base, BIT(3), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 1, 3);
+
+ clk = clk_reg_prcc_kclk("p1_msp1_kclk", "msp1clk",
+ clkrst1_base, BIT(4), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 1, 4);
+
+ clk = clk_reg_prcc_kclk("p1_sdi0_kclk", "sdmmcclk",
+ clkrst1_base, BIT(5), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 1, 5);
+
+ clk = clk_reg_prcc_kclk("p1_i2c2_kclk", "i2cclk",
+ clkrst1_base, BIT(6), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 1, 6);
+
+ clk = clk_reg_prcc_kclk("p1_slimbus0_kclk", "slimclk",
+ clkrst1_base, BIT(8), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 1, 8);
+
+ clk = clk_reg_prcc_kclk("p1_i2c4_kclk", "i2cclk",
+ clkrst1_base, BIT(9), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 1, 9);
+
+ clk = clk_reg_prcc_kclk("p1_msp3_kclk", "msp1clk",
+ clkrst1_base, BIT(10), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 1, 10);
+
+ /* Periph2 */
+ clk = clk_reg_prcc_kclk("p2_i2c3_kclk", "i2cclk",
+ clkrst2_base, BIT(0), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 2, 0);
+
+ clk = clk_reg_prcc_kclk("p2_sdi4_kclk", "sdmmcclk",
+ clkrst2_base, BIT(2), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 2, 2);
+
+ clk = clk_reg_prcc_kclk("p2_msp2_kclk", "msp02clk",
+ clkrst2_base, BIT(3), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 2, 3);
+
+ clk = clk_reg_prcc_kclk("p2_sdi1_kclk", "sdmmcclk",
+ clkrst2_base, BIT(4), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 2, 4);
+
+ clk = clk_reg_prcc_kclk("p2_sdi3_kclk", "sdmmcclk",
+ clkrst2_base, BIT(5), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 2, 5);
+
+ /* Note that rate is received from parent. */
+ clk = clk_reg_prcc_kclk("p2_ssirx_kclk", "hsirxclk",
+ clkrst2_base, BIT(6),
+ CLK_SET_RATE_GATE|CLK_SET_RATE_PARENT);
+ PRCC_KCLK_STORE(clk, 2, 6);
+
+ clk = clk_reg_prcc_kclk("p2_ssitx_kclk", "hsitxclk",
+ clkrst2_base, BIT(7),
+ CLK_SET_RATE_GATE|CLK_SET_RATE_PARENT);
+ PRCC_KCLK_STORE(clk, 2, 7);
+
+ /* Periph3 */
+ clk = clk_reg_prcc_kclk("p3_ssp0_kclk", "sspclk",
+ clkrst3_base, BIT(1), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 3, 1);
+
+ clk = clk_reg_prcc_kclk("p3_ssp1_kclk", "sspclk",
+ clkrst3_base, BIT(2), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 3, 2);
+
+ clk = clk_reg_prcc_kclk("p3_i2c0_kclk", "i2cclk",
+ clkrst3_base, BIT(3), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 3, 3);
+
+ clk = clk_reg_prcc_kclk("p3_sdi2_kclk", "sdmmcclk",
+ clkrst3_base, BIT(4), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 3, 4);
+
+ clk = clk_reg_prcc_kclk("p3_ske_kclk", "rtc32k",
+ clkrst3_base, BIT(5), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 3, 5);
+
+ clk = clk_reg_prcc_kclk("p3_uart2_kclk", "uartclk",
+ clkrst3_base, BIT(6), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 3, 6);
+
+ clk = clk_reg_prcc_kclk("p3_sdi5_kclk", "sdmmcclk",
+ clkrst3_base, BIT(7), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 3, 7);
+
+ /* Periph6 */
+ clk = clk_reg_prcc_kclk("p3_rng_kclk", "rngclk",
+ clkrst6_base, BIT(0), CLK_SET_RATE_GATE);
+ PRCC_KCLK_STORE(clk, 6, 0);
+
+ for_each_child_of_node(np, child) {
+ static struct clk_onecell_data clk_data;
+
+ if (!of_node_cmp(child->name, "prcmu-clock")) {
+ clk_data.clks = prcmu_clk;
+ clk_data.clk_num = ARRAY_SIZE(prcmu_clk);
+ of_clk_add_provider(child, of_clk_src_onecell_get, &clk_data);
+ }
+ if (!of_node_cmp(child->name, "prcc-periph-clock"))
+ of_clk_add_provider(child, ux500_twocell_get, prcc_pclk);
+
+ if (!of_node_cmp(child->name, "prcc-kernel-clock"))
+ of_clk_add_provider(child, ux500_twocell_get, prcc_kclk);
+
+ if (!of_node_cmp(child->name, "rtc32k-clock"))
+ of_clk_add_provider(child, of_clk_src_simple_get, rtc_clk);
+
+ if (!of_node_cmp(child->name, "smp-twd-clock"))
+ of_clk_add_provider(child, of_clk_src_simple_get, twd_clk);
+ }
+}
clk_register_clkdev(clk, NULL, "lcd");
clk_register_clkdev(clk, "lcd", "mcde");
- clk = clk_reg_prcmu_opp_gate("bmlclk", NULL, PRCMU_BML8580CLK,
+ clk = clk_reg_prcmu_opp_gate("bmlclk", NULL, PRCMU_BMLCLK,
CLK_IS_ROOT);
clk_register_clkdev(clk, NULL, "bml");
#include <linux/clk.h>
#include <linux/err.h>
#include <linux/io.h>
-
-#include <asm/mach/irq.h>
+#include <linux/irq.h>
+#include <linux/platform_device.h>
+#include <linux/platform_data/gpio-davinci.h>
struct davinci_gpio_regs {
u32 dir;
u32 intstat;
};
+#define BINTEN 0x8 /* GPIO Interrupt Per-Bank Enable Register */
+
#define chip2controller(chip) \
container_of(chip, struct davinci_gpio_controller, chip)
-static struct davinci_gpio_controller chips[DIV_ROUND_UP(DAVINCI_N_GPIO, 32)];
static void __iomem *gpio_base;
-static struct davinci_gpio_regs __iomem __init *gpio2regs(unsigned gpio)
+static struct davinci_gpio_regs __iomem *gpio2regs(unsigned gpio)
{
void __iomem *ptr;
return g;
}
-static int __init davinci_gpio_irq_setup(void);
+static int davinci_gpio_irq_setup(struct platform_device *pdev);
/*--------------------------------------------------------------------------*/
__raw_writel((1 << offset), value ? &g->set_data : &g->clr_data);
}
-static int __init davinci_gpio_setup(void)
+static int davinci_gpio_probe(struct platform_device *pdev)
{
int i, base;
unsigned ngpio;
- struct davinci_soc_info *soc_info = &davinci_soc_info;
- struct davinci_gpio_regs *regs;
-
- if (soc_info->gpio_type != GPIO_TYPE_DAVINCI)
- return 0;
+ struct davinci_gpio_controller *chips;
+ struct davinci_gpio_platform_data *pdata;
+ struct davinci_gpio_regs __iomem *regs;
+ struct device *dev = &pdev->dev;
+ struct resource *res;
+
+ pdata = dev->platform_data;
+ if (!pdata) {
+ dev_err(dev, "No platform data found\n");
+ return -EINVAL;
+ }
/*
* The gpio banks conceptually expose a segmented bitmap,
* and "ngpio" is one more than the largest zero-based
* bit index that's valid.
*/
- ngpio = soc_info->gpio_num;
+ ngpio = pdata->ngpio;
if (ngpio == 0) {
- pr_err("GPIO setup: how many GPIOs?\n");
+ dev_err(dev, "How many GPIOs?\n");
return -EINVAL;
}
if (WARN_ON(DAVINCI_N_GPIO < ngpio))
ngpio = DAVINCI_N_GPIO;
- gpio_base = ioremap(soc_info->gpio_base, SZ_4K);
- if (WARN_ON(!gpio_base))
+ chips = devm_kzalloc(dev,
+ ngpio * sizeof(struct davinci_gpio_controller),
+ GFP_KERNEL);
+ if (!chips) {
+ dev_err(dev, "Memory allocation failed\n");
return -ENOMEM;
+ }
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ dev_err(dev, "Invalid memory resource\n");
+ return -EBUSY;
+ }
+
+ gpio_base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(gpio_base))
+ return PTR_ERR(gpio_base);
for (i = 0, base = 0; base < ngpio; i++, base += 32) {
chips[i].chip.label = "DaVinci";
gpiochip_add(&chips[i].chip);
}
- soc_info->gpio_ctlrs = chips;
- soc_info->gpio_ctlrs_num = DIV_ROUND_UP(ngpio, 32);
-
- davinci_gpio_irq_setup();
+ platform_set_drvdata(pdev, chips);
+ davinci_gpio_irq_setup(pdev);
return 0;
}
-pure_initcall(davinci_gpio_setup);
/*--------------------------------------------------------------------------*/
/*
static int gpio_to_irq_unbanked(struct gpio_chip *chip, unsigned offset)
{
- struct davinci_soc_info *soc_info = &davinci_soc_info;
+ struct davinci_gpio_controller *d = chip2controller(chip);
- /* NOTE: we assume for now that only irqs in the first gpio_chip
+ /*
+ * NOTE: we assume for now that only irqs in the first gpio_chip
* can provide direct-mapped IRQs to AINTC (up to 32 GPIOs).
*/
- if (offset < soc_info->gpio_unbanked)
- return soc_info->gpio_irq + offset;
+ if (offset < d->irq_base)
+ return d->gpio_irq + offset;
else
return -ENODEV;
}
{
struct davinci_gpio_controller *d;
struct davinci_gpio_regs __iomem *g;
- struct davinci_soc_info *soc_info = &davinci_soc_info;
u32 mask;
d = (struct davinci_gpio_controller *)data->handler_data;
g = (struct davinci_gpio_regs __iomem *)d->regs;
- mask = __gpio_mask(data->irq - soc_info->gpio_irq);
+ mask = __gpio_mask(data->irq - d->gpio_irq);
if (trigger & ~(IRQ_TYPE_EDGE_FALLING | IRQ_TYPE_EDGE_RISING))
return -EINVAL;
* (dm6446) can be set appropriately for GPIOV33 pins.
*/
-static int __init davinci_gpio_irq_setup(void)
+static int davinci_gpio_irq_setup(struct platform_device *pdev)
{
unsigned gpio, irq, bank;
struct clk *clk;
u32 binten = 0;
unsigned ngpio, bank_irq;
- struct davinci_soc_info *soc_info = &davinci_soc_info;
- struct davinci_gpio_regs __iomem *g;
+ struct device *dev = &pdev->dev;
+ struct resource *res;
+ struct davinci_gpio_controller *chips = platform_get_drvdata(pdev);
+ struct davinci_gpio_platform_data *pdata = dev->platform_data;
+ struct davinci_gpio_regs __iomem *g;
- ngpio = soc_info->gpio_num;
+ ngpio = pdata->ngpio;
+ res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+ if (!res) {
+ dev_err(dev, "Invalid IRQ resource\n");
+ return -EBUSY;
+ }
- bank_irq = soc_info->gpio_irq;
- if (bank_irq == 0) {
- printk(KERN_ERR "Don't know first GPIO bank IRQ.\n");
- return -EINVAL;
+ bank_irq = res->start;
+
+ if (!bank_irq) {
+ dev_err(dev, "Invalid IRQ resource\n");
+ return -ENODEV;
}
- clk = clk_get(NULL, "gpio");
+ clk = devm_clk_get(dev, "gpio");
if (IS_ERR(clk)) {
printk(KERN_ERR "Error %ld getting gpio clock?\n",
PTR_ERR(clk));
}
clk_prepare_enable(clk);
- /* Arrange gpio_to_irq() support, handling either direct IRQs or
+ /*
+ * Arrange gpio_to_irq() support, handling either direct IRQs or
* banked IRQs. Having GPIOs in the first GPIO bank use direct
* IRQs, while the others use banked IRQs, would need some setup
* tweaks to recognize hardware which can do that.
*/
for (gpio = 0, bank = 0; gpio < ngpio; bank++, gpio += 32) {
chips[bank].chip.to_irq = gpio_to_irq_banked;
- chips[bank].irq_base = soc_info->gpio_unbanked
+ chips[bank].irq_base = pdata->gpio_unbanked
? -EINVAL
- : (soc_info->intc_irq_num + gpio);
+ : (pdata->intc_irq_num + gpio);
}
/*
* controller only handling trigger modes. We currently assume no
* IRQ mux conflicts; gpio_irq_type_unbanked() is only for GPIOs.
*/
- if (soc_info->gpio_unbanked) {
+ if (pdata->gpio_unbanked) {
static struct irq_chip_type gpio_unbanked;
/* pass "bank 0" GPIO IRQs to AINTC */
__raw_writel(~0, &g->set_rising);
/* set the direct IRQs up to use that irqchip */
- for (gpio = 0; gpio < soc_info->gpio_unbanked; gpio++, irq++) {
+ for (gpio = 0; gpio < pdata->gpio_unbanked; gpio++, irq++) {
irq_set_chip(irq, &gpio_unbanked.chip);
irq_set_handler_data(irq, &chips[gpio / 32]);
irq_set_status_flags(irq, IRQ_TYPE_EDGE_BOTH);
}
done:
- /* BINTEN -- per-bank interrupt enable. genirq would also let these
+ /*
+ * BINTEN -- per-bank interrupt enable. genirq would also let these
* bits be set/cleared dynamically.
*/
- __raw_writel(binten, gpio_base + 0x08);
+ __raw_writel(binten, gpio_base + BINTEN);
printk(KERN_INFO "DaVinci: %d gpio irqs\n", irq - gpio_to_irq(0));
return 0;
}
+
+static struct platform_driver davinci_gpio_driver = {
+ .probe = davinci_gpio_probe,
+ .driver = {
+ .name = "davinci_gpio",
+ .owner = THIS_MODULE,
+ },
+};
+
+/**
+ * GPIO driver registration needs to be done before machine_init functions
+ * access GPIO. Hence davinci_gpio_drv_reg() is a postcore_initcall.
+ */
+static int __init davinci_gpio_drv_reg(void)
+{
+ return platform_driver_register(&davinci_gpio_driver);
+}
+postcore_initcall(davinci_gpio_drv_reg);
int i, nr_chips;
int group = 0;
-#if defined(CONFIG_PINCTRL_EXYNOS) || defined(CONFIG_PINCTRL_EXYNOS5440)
/*
- * This gpio driver includes support for device tree support and there
- * are platforms using it. In order to maintain compatibility with those
- * platforms, and to allow non-dt Exynos4210 platforms to use this
- * gpiolib support, a check is added to find out if there is a active
- * pin-controller driver support available. If it is available, this
- * gpiolib support is ignored and the gpiolib support available in
- * pin-controller driver is used. This is a temporary check and will go
- * away when all of the Exynos4210 platforms have switched to using
- * device tree and the pin-ctrl driver.
- */
- struct device_node *pctrl_np;
- static const struct of_device_id exynos_pinctrl_ids[] = {
- { .compatible = "samsung,s3c2412-pinctrl", },
- { .compatible = "samsung,s3c2416-pinctrl", },
- { .compatible = "samsung,s3c2440-pinctrl", },
- { .compatible = "samsung,s3c2450-pinctrl", },
- { .compatible = "samsung,exynos4210-pinctrl", },
- { .compatible = "samsung,exynos4x12-pinctrl", },
- { .compatible = "samsung,exynos5250-pinctrl", },
- { .compatible = "samsung,exynos5440-pinctrl", },
- { }
- };
- for_each_matching_node(pctrl_np, exynos_pinctrl_ids)
- if (pctrl_np && of_device_is_available(pctrl_np))
- return -ENODEV;
-#endif
+ * Currently there are two drivers that can provide GPIO support for
+ * Samsung SoCs. For device tree enabled platforms, the new
+ * pinctrl-samsung driver is used, providing both GPIO and pin control
+ * interfaces. For legacy (non-DT) platforms this driver is used.
+ */
+ if (of_have_populated_dt())
+ return -ENODEV;
samsung_gpiolib_set_cfg(samsung_gpio_cfgs, ARRAY_SIZE(samsung_gpio_cfgs));
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/gpio.h>
+#include <linux/platform_data/gpio-davinci.h>
#include <mach/common.h>
#include <mach/tnetv107x.h>
config IDE_GENERIC
tristate "generic/default IDE chipset support"
- depends on ALPHA || X86 || IA64 || M32R || MIPS || ARCH_RPC || ARCH_SHARK
- default ARM && (ARCH_RPC || ARCH_SHARK)
+ depends on ALPHA || X86 || IA64 || M32R || MIPS || ARCH_RPC
+ default ARM && ARCH_RPC
help
This is the generic IDE driver. This driver attaches to the
fixed legacy ports (e.g. on PCs 0x1f0/0x170, 0x1e8/0x168 and
config SERIO_I8042
tristate "i8042 PC Keyboard controller" if EXPERT || !X86
default y
- depends on !PARISC && (!ARM || ARCH_SHARK || FOOTBRIDGE_HOST) && \
+ depends on !PARISC && (!ARM || FOOTBRIDGE_HOST) && \
(!SUPERH || SH_CAYMAN) && !M68K && !BLACKFIN && !S390 && \
!ARC
help
#include <linux/io.h>
#include <linux/of_address.h>
#include <linux/of_irq.h>
+#include <linux/of_pci.h>
#include <linux/irqdomain.h>
+#include <linux/slab.h>
+#include <linux/msi.h>
#include <asm/mach/arch.h>
#include <asm/exception.h>
#include <asm/smp_plat.h>
#define IPI_DOORBELL_START (0)
#define IPI_DOORBELL_END (8)
#define IPI_DOORBELL_MASK 0xFF
+#define PCI_MSI_DOORBELL_START (16)
+#define PCI_MSI_DOORBELL_NR (16)
+#define PCI_MSI_DOORBELL_END (32)
+#define PCI_MSI_DOORBELL_MASK 0xFFFF0000
static DEFINE_RAW_SPINLOCK(irq_controller_lock);
static void __iomem *per_cpu_int_base;
static void __iomem *main_int_base;
static struct irq_domain *armada_370_xp_mpic_domain;
+#ifdef CONFIG_PCI_MSI
+static struct irq_domain *armada_370_xp_msi_domain;
+static DECLARE_BITMAP(msi_used, PCI_MSI_DOORBELL_NR);
+static DEFINE_MUTEX(msi_used_lock);
+static phys_addr_t msi_doorbell_addr;
+#endif
/*
* In SMP mode:
ARMADA_370_XP_INT_CLEAR_MASK_OFFS);
}
+#ifdef CONFIG_PCI_MSI
+
+static int armada_370_xp_alloc_msi(void)
+{
+ int hwirq;
+
+ mutex_lock(&msi_used_lock);
+ hwirq = find_first_zero_bit(&msi_used, PCI_MSI_DOORBELL_NR);
+ if (hwirq >= PCI_MSI_DOORBELL_NR)
+ hwirq = -ENOSPC;
+ else
+ set_bit(hwirq, msi_used);
+ mutex_unlock(&msi_used_lock);
+
+ return hwirq;
+}
+
+static void armada_370_xp_free_msi(int hwirq)
+{
+ mutex_lock(&msi_used_lock);
+ if (!test_bit(hwirq, msi_used))
+ pr_err("trying to free unused MSI#%d\n", hwirq);
+ else
+ clear_bit(hwirq, msi_used);
+ mutex_unlock(&msi_used_lock);
+}
+
+static int armada_370_xp_setup_msi_irq(struct msi_chip *chip,
+ struct pci_dev *pdev,
+ struct msi_desc *desc)
+{
+ struct msi_msg msg;
+ irq_hw_number_t hwirq;
+ int virq;
+
+ hwirq = armada_370_xp_alloc_msi();
+ if (hwirq < 0)
+ return hwirq;
+
+ virq = irq_create_mapping(armada_370_xp_msi_domain, hwirq);
+ if (!virq) {
+ armada_370_xp_free_msi(hwirq);
+ return -EINVAL;
+ }
+
+ irq_set_msi_desc(virq, desc);
+
+ msg.address_lo = msi_doorbell_addr;
+ msg.address_hi = 0;
+ msg.data = 0xf00 | (hwirq + 16);
+
+ write_msi_msg(virq, &msg);
+ return 0;
+}
+
+static void armada_370_xp_teardown_msi_irq(struct msi_chip *chip,
+ unsigned int irq)
+{
+ struct irq_data *d = irq_get_irq_data(irq);
+ irq_dispose_mapping(irq);
+ armada_370_xp_free_msi(d->hwirq);
+}
+
+static struct irq_chip armada_370_xp_msi_irq_chip = {
+ .name = "armada_370_xp_msi_irq",
+ .irq_enable = unmask_msi_irq,
+ .irq_disable = mask_msi_irq,
+ .irq_mask = mask_msi_irq,
+ .irq_unmask = unmask_msi_irq,
+};
+
+static int armada_370_xp_msi_map(struct irq_domain *domain, unsigned int virq,
+ irq_hw_number_t hw)
+{
+ irq_set_chip_and_handler(virq, &armada_370_xp_msi_irq_chip,
+ handle_simple_irq);
+ set_irq_flags(virq, IRQF_VALID);
+
+ return 0;
+}
+
+static const struct irq_domain_ops armada_370_xp_msi_irq_ops = {
+ .map = armada_370_xp_msi_map,
+};
+
+static int armada_370_xp_msi_init(struct device_node *node,
+ phys_addr_t main_int_phys_base)
+{
+ struct msi_chip *msi_chip;
+ u32 reg;
+ int ret;
+
+ msi_doorbell_addr = main_int_phys_base +
+ ARMADA_370_XP_SW_TRIG_INT_OFFS;
+
+ msi_chip = kzalloc(sizeof(*msi_chip), GFP_KERNEL);
+ if (!msi_chip)
+ return -ENOMEM;
+
+ msi_chip->setup_irq = armada_370_xp_setup_msi_irq;
+ msi_chip->teardown_irq = armada_370_xp_teardown_msi_irq;
+ msi_chip->of_node = node;
+
+ armada_370_xp_msi_domain =
+ irq_domain_add_linear(NULL, PCI_MSI_DOORBELL_NR,
+ &armada_370_xp_msi_irq_ops,
+ NULL);
+ if (!armada_370_xp_msi_domain) {
+ kfree(msi_chip);
+ return -ENOMEM;
+ }
+
+ ret = of_pci_msi_chip_add(msi_chip);
+ if (ret < 0) {
+ irq_domain_remove(armada_370_xp_msi_domain);
+ kfree(msi_chip);
+ return ret;
+ }
+
+ reg = readl(per_cpu_int_base + ARMADA_370_XP_IN_DRBEL_MSK_OFFS)
+ | PCI_MSI_DOORBELL_MASK;
+
+ writel(reg, per_cpu_int_base +
+ ARMADA_370_XP_IN_DRBEL_MSK_OFFS);
+
+ /* Unmask IPI interrupt */
+ writel(1, per_cpu_int_base + ARMADA_370_XP_INT_CLEAR_MASK_OFFS);
+
+ return 0;
+}
+#else
+static inline int armada_370_xp_msi_init(struct device_node *node,
+ phys_addr_t main_int_phys_base)
+{
+ return 0;
+}
+#endif
+
#ifdef CONFIG_SMP
static int armada_xp_set_affinity(struct irq_data *d,
const struct cpumask *mask_val, bool force)
if (irqnr > 1022)
break;
- if (irqnr > 0) {
+ if (irqnr > 1) {
irqnr = irq_find_mapping(armada_370_xp_mpic_domain,
irqnr);
handle_IRQ(irqnr, regs);
continue;
}
+
+#ifdef CONFIG_PCI_MSI
+ /* MSI handling */
+ if (irqnr == 1) {
+ u32 msimask, msinr;
+
+ msimask = readl_relaxed(per_cpu_int_base +
+ ARMADA_370_XP_IN_DRBEL_CAUSE_OFFS)
+ & PCI_MSI_DOORBELL_MASK;
+
+ writel(~PCI_MSI_DOORBELL_MASK, per_cpu_int_base +
+ ARMADA_370_XP_IN_DRBEL_CAUSE_OFFS);
+
+ for (msinr = PCI_MSI_DOORBELL_START;
+ msinr < PCI_MSI_DOORBELL_END; msinr++) {
+ int irq;
+
+ if (!(msimask & BIT(msinr)))
+ continue;
+
+ irq = irq_find_mapping(armada_370_xp_msi_domain,
+ msinr - 16);
+ handle_IRQ(irq, regs);
+ }
+ }
+#endif
+
#ifdef CONFIG_SMP
/* IPI Handling */
if (irqnr == 0) {
static int __init armada_370_xp_mpic_of_init(struct device_node *node,
struct device_node *parent)
{
+ struct resource main_int_res, per_cpu_int_res;
u32 control;
- main_int_base = of_iomap(node, 0);
- per_cpu_int_base = of_iomap(node, 1);
+ BUG_ON(of_address_to_resource(node, 0, &main_int_res));
+ BUG_ON(of_address_to_resource(node, 1, &per_cpu_int_res));
+
+ BUG_ON(!request_mem_region(main_int_res.start,
+ resource_size(&main_int_res),
+ node->full_name));
+ BUG_ON(!request_mem_region(per_cpu_int_res.start,
+ resource_size(&per_cpu_int_res),
+ node->full_name));
+ main_int_base = ioremap(main_int_res.start,
+ resource_size(&main_int_res));
BUG_ON(!main_int_base);
+
+ per_cpu_int_base = ioremap(per_cpu_int_res.start,
+ resource_size(&per_cpu_int_res));
BUG_ON(!per_cpu_int_base);
control = readl(main_int_base + ARMADA_370_XP_INT_CONTROL);
irq_domain_add_linear(node, (control >> 2) & 0x3ff,
&armada_370_xp_mpic_irq_ops, NULL);
- if (!armada_370_xp_mpic_domain)
- panic("Unable to add Armada_370_Xp MPIC irq domain (DT)\n");
+ BUG_ON(!armada_370_xp_mpic_domain);
irq_set_default_host(armada_370_xp_mpic_domain);
#endif
+ armada_370_xp_msi_init(node, main_int_res.start);
+
set_handle_irq(armada_370_xp_handle_irq);
return 0;
int __init vic_of_init(struct device_node *node, struct device_node *parent)
{
void __iomem *regs;
+ u32 interrupt_mask = ~0;
+ u32 wakeup_mask = ~0;
if (WARN(parent, "non-root VICs are not supported"))
return -EINVAL;
if (WARN_ON(!regs))
return -EIO;
+ of_property_read_u32(node, "valid-mask", &interrupt_mask);
+ of_property_read_u32(node, "valid-wakeup-mask", &wakeup_mask);
+
/*
* Passing 0 as first IRQ makes the simple domain allocate descriptors
*/
- __vic_init(regs, 0, ~0, ~0, node);
+ __vic_init(regs, 0, interrupt_mask, wakeup_mask, node);
return 0;
}
CLK_MGT_ENTRY(PER6CLK, PLL_DIV, true),
CLK_MGT_ENTRY(PER7CLK, PLL_DIV, true),
CLK_MGT_ENTRY(LCDCLK, PLL_FIX, true),
- CLK_MGT_ENTRY(BML8580CLK, PLL_DIV, true),
CLK_MGT_ENTRY(BMLCLK, PLL_DIV, true),
CLK_MGT_ENTRY(HSITXCLK, PLL_DIV, true),
CLK_MGT_ENTRY(HSIRXCLK, PLL_DIV, true),
#define PRCM_PER7CLK_MGT (0x040)
#define PRCM_LCDCLK_MGT (0x044)
#define PRCM_BMLCLK_MGT (0x04C)
-#define PRCM_BML8580CLK_MGT (0x108)
#define PRCM_HSITXCLK_MGT (0x050)
#define PRCM_HSIRXCLK_MGT (0x054)
#define PRCM_HDMICLK_MGT (0x058)
config PCI_MVEBU
bool "Marvell EBU PCIe controller"
- depends on ARCH_MVEBU || ARCH_KIRKWOOD
+ depends on ARCH_MVEBU || ARCH_DOVE || ARCH_KIRKWOOD
depends on OF
config PCIE_DW
#include <linux/kernel.h>
#include <linux/pci.h>
#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/gpio.h>
#include <linux/module.h>
#include <linux/mbus.h>
+#include <linux/msi.h>
#include <linux/slab.h>
#include <linux/platform_device.h>
#include <linux/of_address.h>
-#include <linux/of_pci.h>
#include <linux/of_irq.h>
+#include <linux/of_gpio.h>
+#include <linux/of_pci.h>
#include <linux/of_platform.h>
/*
struct mvebu_pcie {
struct platform_device *pdev;
struct mvebu_pcie_port *ports;
+ struct msi_chip *msi;
struct resource io;
struct resource realio;
struct resource mem;
unsigned int io_target;
unsigned int io_attr;
struct clk *clk;
+ int reset_gpio;
+ int reset_active_low;
+ char *reset_name;
struct mvebu_sw_pci_bridge bridge;
struct device_node *dn;
struct mvebu_pcie *pcie;
* BAR[0,2] -> disabled, BAR[1] -> covers all DRAM banks
* WIN[0-3] -> DRAM bank[0-3]
*/
-static void __init mvebu_pcie_setup_wins(struct mvebu_pcie_port *port)
+static void mvebu_pcie_setup_wins(struct mvebu_pcie_port *port)
{
const struct mbus_dram_target_info *dram;
u32 size;
port->base + PCIE_BAR_CTRL_OFF(1));
}
-static void __init mvebu_pcie_setup_hw(struct mvebu_pcie_port *port)
+static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port)
{
u16 cmd;
u32 mask;
.write = mvebu_pcie_wr_conf,
};
-static int __init mvebu_pcie_setup(int nr, struct pci_sys_data *sys)
+static int mvebu_pcie_setup(int nr, struct pci_sys_data *sys)
{
struct mvebu_pcie *pcie = sys_to_pcie(sys);
int i;
return 1;
}
-static int __init mvebu_pcie_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+static int mvebu_pcie_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
{
struct of_irq oirq;
int ret;
return bus;
}
+void mvebu_pcie_add_bus(struct pci_bus *bus)
+{
+ struct mvebu_pcie *pcie = sys_to_pcie(bus->sysdata);
+ bus->msi = pcie->msi;
+}
+
resource_size_t mvebu_pcie_align_resource(struct pci_dev *dev,
const struct resource *res,
resource_size_t start,
return start;
}
-static void __init mvebu_pcie_enable(struct mvebu_pcie *pcie)
+static void mvebu_pcie_enable(struct mvebu_pcie *pcie)
{
struct hw_pci hw;
hw.map_irq = mvebu_pcie_map_irq;
hw.ops = &mvebu_pcie_ops;
hw.align_resource = mvebu_pcie_align_resource;
+ hw.add_bus = mvebu_pcie_add_bus;
pci_common_init(&hw);
}
* <...> property for one that matches the given port/lane. Once
* found, maps it.
*/
-static void __iomem * __init
-mvebu_pcie_map_registers(struct platform_device *pdev,
- struct device_node *np,
- struct mvebu_pcie_port *port)
+static void __iomem *mvebu_pcie_map_registers(struct platform_device *pdev,
+ struct device_node *np, struct mvebu_pcie_port *port)
{
struct resource regs;
int ret = 0;
return -ENOENT;
}
-static int __init mvebu_pcie_probe(struct platform_device *pdev)
+static void mvebu_pcie_msi_enable(struct mvebu_pcie *pcie)
+{
+ struct device_node *msi_node;
+
+ msi_node = of_parse_phandle(pcie->pdev->dev.of_node,
+ "msi-parent", 0);
+ if (!msi_node)
+ return;
+
+ pcie->msi = of_pci_find_msi_chip_by_node(msi_node);
+
+ if (pcie->msi)
+ pcie->msi->dev = &pcie->pdev->dev;
+}
+
+static int mvebu_pcie_probe(struct platform_device *pdev)
{
struct mvebu_pcie *pcie;
struct device_node *np = pdev->dev.of_node;
return -ENOMEM;
pcie->pdev = pdev;
+ platform_set_drvdata(pdev, pcie);
/* Get the PCIe memory and I/O aperture */
mvebu_mbus_get_pcie_mem_aperture(&pcie->mem);
return ret;
}
+ i = 0;
for_each_child_of_node(pdev->dev.of_node, child) {
if (!of_device_is_available(child))
continue;
- pcie->nports++;
+ i++;
}
- pcie->ports = devm_kzalloc(&pdev->dev, pcie->nports *
+ pcie->ports = devm_kzalloc(&pdev->dev, i *
sizeof(struct mvebu_pcie_port),
GFP_KERNEL);
if (!pcie->ports)
i = 0;
for_each_child_of_node(pdev->dev.of_node, child) {
struct mvebu_pcie_port *port = &pcie->ports[i];
+ enum of_gpio_flags flags;
if (!of_device_is_available(child))
continue;
continue;
}
+ port->reset_gpio = of_get_named_gpio_flags(child,
+ "reset-gpios", 0, &flags);
+ if (gpio_is_valid(port->reset_gpio)) {
+ u32 reset_udelay = 20000;
+
+ port->reset_active_low = flags & OF_GPIO_ACTIVE_LOW;
+ port->reset_name = kasprintf(GFP_KERNEL,
+ "pcie%d.%d-reset", port->port, port->lane);
+ of_property_read_u32(child, "reset-delay-us",
+ &reset_udelay);
+
+ ret = devm_gpio_request_one(&pdev->dev,
+ port->reset_gpio, GPIOF_DIR_OUT, port->reset_name);
+ if (ret) {
+ if (ret == -EPROBE_DEFER)
+ return ret;
+ continue;
+ }
+
+ gpio_set_value(port->reset_gpio,
+ (port->reset_active_low) ? 1 : 0);
+ msleep(reset_udelay/1000);
+ }
+
+ port->clk = of_clk_get_by_name(child, NULL);
+ if (IS_ERR(port->clk)) {
+ dev_err(&pdev->dev, "PCIe%d.%d: cannot get clock\n",
+ port->port, port->lane);
+ continue;
+ }
+
+ ret = clk_prepare_enable(port->clk);
+ if (ret)
+ continue;
+
port->base = mvebu_pcie_map_registers(pdev, child, port);
if (IS_ERR(port->base)) {
dev_err(&pdev->dev, "PCIe%d.%d: cannot map registers\n",
port->port, port->lane);
port->base = NULL;
+ clk_disable_unprepare(port->clk);
continue;
}
port->port, port->lane);
}
- port->clk = of_clk_get_by_name(child, NULL);
- if (IS_ERR(port->clk)) {
- dev_err(&pdev->dev, "PCIe%d.%d: cannot get clock\n",
- port->port, port->lane);
- iounmap(port->base);
- port->haslink = 0;
- continue;
- }
-
port->dn = child;
-
- clk_prepare_enable(port->clk);
spin_lock_init(&port->conf_lock);
-
mvebu_sw_pci_bridge_init(port);
-
i++;
}
+ pcie->nports = i;
+ mvebu_pcie_msi_enable(pcie);
mvebu_pcie_enable(pcie);
return 0;
static const struct of_device_id mvebu_pcie_of_match_table[] = {
{ .compatible = "marvell,armada-xp-pcie", },
{ .compatible = "marvell,armada-370-pcie", },
+ { .compatible = "marvell,dove-pcie", },
{ .compatible = "marvell,kirkwood-pcie", },
{},
};
.name = "mvebu-pcie",
.of_match_table =
of_match_ptr(mvebu_pcie_of_match_table),
+ /* driver unloading/unbinding currently not supported */
+ .suppress_bind_attrs = true,
},
+ .probe = mvebu_pcie_probe,
};
-
-static int __init mvebu_pcie_init(void)
-{
- return platform_driver_probe(&mvebu_pcie_driver,
- mvebu_pcie_probe);
-}
-
-subsys_initcall(mvebu_pcie_init);
+module_platform_driver(mvebu_pcie_driver);
MODULE_AUTHOR("Thomas Petazzoni <thomas.petazzoni@free-electrons.com>");
MODULE_DESCRIPTION("Marvell EBU PCIe driver");
goto err1;
}
- clk = clk_get(&pdev->dev, "usb");
+ clk = clk_get(&pdev->dev, NULL);
if (IS_ERR(clk)) {
dev_err(&pdev->dev, "failed to get clock\n");
ret = PTR_ERR(clk);
cyber2000fb_set_par(&cfb->fb);
}
-#ifdef CONFIG_ARCH_SHARK
-
-#include <mach/framebuffer.h>
-
-static int cyberpro_vl_probe(void)
-{
- struct cfb_info *cfb;
- int err = -ENOMEM;
-
- if (!request_mem_region(FB_START, FB_SIZE, "CyberPro2010"))
- return err;
-
- cfb = cyberpro_alloc_fb_info(ID_CYBERPRO_2010, "CyberPro2010");
- if (!cfb)
- goto failed_release;
-
- cfb->irq = -1;
- cfb->region = ioremap(FB_START, FB_SIZE);
- if (!cfb->region)
- goto failed_ioremap;
-
- cfb->regs = cfb->region + MMIO_OFFSET;
- cfb->fb.device = NULL;
- cfb->fb.fix.mmio_start = FB_START + MMIO_OFFSET;
- cfb->fb.fix.smem_start = FB_START;
-
- /*
- * Bring up the hardware. This is expected to enable access
- * to the linear memory region, and allow access to the memory
- * mapped registers. Also, mem_ctl1 and mem_ctl2 must be
- * initialised.
- */
- cyber2000fb_writeb(0x18, 0x46e8, cfb);
- cyber2000fb_writeb(0x01, 0x102, cfb);
- cyber2000fb_writeb(0x08, 0x46e8, cfb);
- cyber2000fb_writeb(EXT_BIU_MISC, 0x3ce, cfb);
- cyber2000fb_writeb(EXT_BIU_MISC_LIN_ENABLE, 0x3cf, cfb);
-
- cfb->mclk_mult = 0xdb;
- cfb->mclk_div = 0x54;
-
- err = cyberpro_common_probe(cfb);
- if (err)
- goto failed;
-
- if (int_cfb_info == NULL)
- int_cfb_info = cfb;
-
- return 0;
-
-failed:
- iounmap(cfb->region);
-failed_ioremap:
- cyberpro_free_fb_info(cfb);
-failed_release:
- release_mem_region(FB_START, FB_SIZE);
-
- return err;
-}
-#endif /* CONFIG_ARCH_SHARK */
-
/*
* PCI specific support.
*/
cyber2000fb_setup(option);
#endif
-#ifdef CONFIG_ARCH_SHARK
- err = cyberpro_vl_probe();
- if (!err)
- ret = 0;
-#endif
-#ifdef CONFIG_PCI
err = pci_register_driver(&cyberpro_driver);
if (!err)
ret = 0;
-#endif
return ret ? err : 0;
}
module_init(cyber2000fb_init);
-#ifndef CONFIG_ARCH_SHARK
static void __exit cyberpro_exit(void)
{
pci_unregister_driver(&cyberpro_driver);
}
module_exit(cyberpro_exit);
-#endif
MODULE_AUTHOR("Russell King");
MODULE_DESCRIPTION("CyberPro 2000, 2010 and 5000 framebuffer driver");
--- /dev/null
+/*
+ * This header provides constants for the PRCMU bindings.
+ *
+ */
+
+#ifndef _DT_BINDINGS_MFD_PRCMU_H
+#define _DT_BINDINGS_MFD_PRCMU_H
+
+/*
+ * Clock identifiers.
+ */
+#define ARMCLK 0
+#define PRCMU_ACLK 1
+#define PRCMU_SVAMMCSPCLK 2
+#define PRCMU_SDMMCHCLK 2 /* DBx540 only. */
+#define PRCMU_SIACLK 3
+#define PRCMU_SIAMMDSPCLK 3 /* DBx540 only. */
+#define PRCMU_SGACLK 4
+#define PRCMU_UARTCLK 5
+#define PRCMU_MSP02CLK 6
+#define PRCMU_MSP1CLK 7
+#define PRCMU_I2CCLK 8
+#define PRCMU_SDMMCCLK 9
+#define PRCMU_SLIMCLK 10
+#define PRCMU_CAMCLK 10 /* DBx540 only. */
+#define PRCMU_PER1CLK 11
+#define PRCMU_PER2CLK 12
+#define PRCMU_PER3CLK 13
+#define PRCMU_PER5CLK 14
+#define PRCMU_PER6CLK 15
+#define PRCMU_PER7CLK 16
+#define PRCMU_LCDCLK 17
+#define PRCMU_BMLCLK 18
+#define PRCMU_HSITXCLK 19
+#define PRCMU_HSIRXCLK 20
+#define PRCMU_HDMICLK 21
+#define PRCMU_APEATCLK 22
+#define PRCMU_APETRACECLK 23
+#define PRCMU_MCDECLK 24
+#define PRCMU_IPI2CCLK 25
+#define PRCMU_DSIALTCLK 26
+#define PRCMU_DMACLK 27
+#define PRCMU_B2R2CLK 28
+#define PRCMU_TVCLK 29
+#define SPARE_UNIPROCLK 30
+#define PRCMU_SSPCLK 31
+#define PRCMU_RNGCLK 32
+#define PRCMU_UICCCLK 33
+#define PRCMU_G1CLK 34 /* DBx540 only. */
+#define PRCMU_HVACLK 35 /* DBx540 only. */
+#define PRCMU_SPARE1CLK 36
+#define PRCMU_SPARE2CLK 37
+
+#define PRCMU_NUM_REG_CLOCKS 38
+
+#define PRCMU_RTCCLK PRCMU_NUM_REG_CLOCKS
+#define PRCMU_SYSCLK 39
+#define PRCMU_CDCLK 40
+#define PRCMU_TIMCLK 41
+#define PRCMU_PLLSOC0 42
+#define PRCMU_PLLSOC1 43
+#define PRCMU_ARMSS 44
+#define PRCMU_PLLDDR 45
+
+/* DSI Clocks */
+#define PRCMU_PLLDSI 46
+#define PRCMU_DSI0CLK 47
+#define PRCMU_DSI1CLK 48
+#define PRCMU_DSI0ESCCLK 49
+#define PRCMU_DSI1ESCCLK 50
+#define PRCMU_DSI2ESCCLK 51
+
+/* LCD DSI PLL - Ux540 only */
+#define PRCMU_PLLDSI_LCD 52
+#define PRCMU_DSI0CLK_LCD 53
+#define PRCMU_DSI1CLK_LCD 54
+#define PRCMU_DSI0ESCCLK_LCD 55
+#define PRCMU_DSI1ESCCLK_LCD 56
+#define PRCMU_DSI2ESCCLK_LCD 57
+
+#define PRCMU_NUM_CLKS 58
+
+#endif
#define PULL_UP (1 << 4)
#define ALTELECTRICALSEL (1 << 5)
-/* 34xx specific mux bit defines */
+/* omap3/4/5 specific mux bit defines */
#define INPUT_EN (1 << 8)
#define OFF_EN (1 << 9)
#define OFFOUT_EN (1 << 10)
#define OFF_PULL_EN (1 << 12)
#define OFF_PULL_UP (1 << 13)
#define WAKEUP_EN (1 << 14)
-
-/* 44xx specific mux bit defines */
#define WAKEUP_EVENT (1 << 15)
/* Active pin states */
#ifndef __LINUX_CLK_MXS_H
#define __LINUX_CLK_MXS_H
-int mx23_clocks_init(void);
-int mx28_clocks_init(void);
int mxs_saif_clkmux_select(unsigned int clkmux);
#endif
+++ /dev/null
-/*
- * Copyright 2012 Maxime Ripard
- *
- * Maxime Ripard <maxime.ripard@free-electrons.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#ifndef __LINUX_CLK_SUNXI_H_
-#define __LINUX_CLK_SUNXI_H_
-
-void __init sunxi_init_clocks(void);
-
-#endif
#include <linux/notifier.h>
#include <linux/err.h>
+#include <dt-bindings/mfd/dbx500-prcmu.h> /* For clock identifiers */
+
/* Offset for the firmware version within the TCPM */
#define DB8500_PRCMU_FW_VERSION_OFFSET 0xA4
#define DBX540_PRCMU_FW_VERSION_OFFSET 0xA8
#define PRCMU_CLKSRC_ARMCLKFIX 0x46
#define PRCMU_CLKSRC_HDMICLK 0x47
-/*
- * Clock identifiers.
- */
-enum prcmu_clock {
- PRCMU_SGACLK,
- PRCMU_UARTCLK,
- PRCMU_MSP02CLK,
- PRCMU_MSP1CLK,
- PRCMU_I2CCLK,
- PRCMU_SDMMCCLK,
- PRCMU_SPARE1CLK,
- PRCMU_SLIMCLK,
- PRCMU_PER1CLK,
- PRCMU_PER2CLK,
- PRCMU_PER3CLK,
- PRCMU_PER5CLK,
- PRCMU_PER6CLK,
- PRCMU_PER7CLK,
- PRCMU_LCDCLK,
- PRCMU_BMLCLK,
- PRCMU_HSITXCLK,
- PRCMU_HSIRXCLK,
- PRCMU_HDMICLK,
- PRCMU_APEATCLK,
- PRCMU_APETRACECLK,
- PRCMU_MCDECLK,
- PRCMU_IPI2CCLK,
- PRCMU_DSIALTCLK,
- PRCMU_DMACLK,
- PRCMU_B2R2CLK,
- PRCMU_TVCLK,
- PRCMU_SSPCLK,
- PRCMU_RNGCLK,
- PRCMU_UICCCLK,
- PRCMU_PWMCLK,
- PRCMU_IRDACLK,
- PRCMU_IRRCCLK,
- PRCMU_SIACLK,
- PRCMU_SVACLK,
- PRCMU_ACLK,
- PRCMU_HVACLK, /* Ux540 only */
- PRCMU_G1CLK, /* Ux540 only */
- PRCMU_SDMMCHCLK,
- PRCMU_CAMCLK,
- PRCMU_BML8580CLK,
- PRCMU_NUM_REG_CLOCKS,
- PRCMU_SYSCLK = PRCMU_NUM_REG_CLOCKS,
- PRCMU_CDCLK,
- PRCMU_TIMCLK,
- PRCMU_PLLSOC0,
- PRCMU_PLLSOC1,
- PRCMU_ARMSS,
- PRCMU_PLLDDR,
- PRCMU_PLLDSI,
- PRCMU_DSI0CLK,
- PRCMU_DSI1CLK,
- PRCMU_DSI0ESCCLK,
- PRCMU_DSI1ESCCLK,
- PRCMU_DSI2ESCCLK,
- /* LCD DSI PLL - Ux540 only */
- PRCMU_PLLDSI_LCD,
- PRCMU_DSI0CLK_LCD,
- PRCMU_DSI1CLK_LCD,
- PRCMU_DSI0ESCCLK_LCD,
- PRCMU_DSI1ESCCLK_LCD,
- PRCMU_DSI2ESCCLK_LCD,
-};
-
/**
* enum prcmu_wdog_id - PRCMU watchdog IDs
* @PRCMU_WDOG_ALL: use all timers
+++ /dev/null
-/* Minimal platform data header */
-void nomadik_clk_init(void);
#ifndef __CLK_UX500_H
#define __CLK_UX500_H
+void u8500_of_clk_init(u32 clkrst1_base, u32 clkrst2_base, u32 clkrst3_base,
+ u32 clkrst5_base, u32 clkrst6_base);
+
void u8500_clk_init(u32 clkrst1_base, u32 clkrst2_base, u32 clkrst3_base,
u32 clkrst5_base, u32 clkrst6_base);
void u9540_clk_init(u32 clkrst1_base, u32 clkrst2_base, u32 clkrst3_base,
--- /dev/null
+/*
+ * DaVinci GPIO Platform Related Defines
+ *
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __DAVINCI_GPIO_PLATFORM_H
+#define __DAVINCI_GPIO_PLATFORM_H
+
+#include <linux/io.h>
+#include <linux/spinlock.h>
+
+#include <asm-generic/gpio.h>
+
+enum davinci_gpio_type {
+ GPIO_TYPE_TNETV107X = 0,
+};
+
+struct davinci_gpio_platform_data {
+ u32 ngpio;
+ u32 gpio_unbanked;
+ u32 intc_irq_num;
+};
+
+
+struct davinci_gpio_controller {
+ struct gpio_chip chip;
+ int irq_base;
+ /* Serialize access to GPIO registers */
+ spinlock_t lock;
+ void __iomem *regs;
+ void __iomem *set_data;
+ void __iomem *clr_data;
+ void __iomem *in_data;
+ int gpio_unbanked;
+ unsigned gpio_irq;
+};
+
+/*
+ * basic gpio routines
+ */
+#define GPIO(X) (X) /* 0 <= X <= (DAVINCI_N_GPIO - 1) */
+
+/* Convert GPIO signal to GPIO pin number */
+#define GPIO_TO_PIN(bank, gpio) (16 * (bank) + (gpio))
+
+static inline u32 __gpio_mask(unsigned gpio)
+{
+ return 1 << (gpio % 32);
+}
+#endif
projects / karo-tx-linux.git / commitdiff