]> git.karo-electronics.de Git - linux-beck.git/commitdiff
spi/atmel: add DT support
authorJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Fri, 23 Nov 2012 12:44:39 +0000 (13:44 +0100)
committerGrant Likely <grant.likely@secretlab.ca>
Mon, 17 Dec 2012 17:11:32 +0000 (17:11 +0000)
Use the newly introduce cs-gpios dt support on atmel.
We do not use the hardware cs as it's wired and has bugs and limitations.
As the controller believes that only active-low devices/systems exists.

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Documentation/devicetree/bindings/spi/spi_atmel.txt [new file with mode: 0644]
drivers/spi/spi-atmel.c

diff --git a/Documentation/devicetree/bindings/spi/spi_atmel.txt b/Documentation/devicetree/bindings/spi/spi_atmel.txt
new file mode 100644 (file)
index 0000000..07e04cd
--- /dev/null
@@ -0,0 +1,26 @@
+Atmel SPI device
+
+Required properties:
+- compatible : should be "atmel,at91rm9200-spi".
+- reg: Address and length of the register set for the device
+- interrupts: Should contain spi interrupt
+- cs-gpios: chipselects
+
+Example:
+
+spi1: spi@fffcc000 {
+       compatible = "atmel,at91rm9200-spi";
+       reg = <0xfffcc000 0x4000>;
+       interrupts = <13 4 5>;
+       #address-cells = <1>;
+       #size-cells = <0>;
+       cs-gpios = <&pioB 3 0>;
+       status = "okay";
+
+       mmc-slot@0 {
+               compatible = "mmc-spi-slot";
+               reg = <0>;
+               gpios = <&pioC 4 0>;    /* CD */
+               spi-max-frequency = <25000000>;
+       };
+};
index 75c0c4f5fdf2a6d02dbbebdf63ad45d3ebd33252..ab34497bcfeee53d9961654de6c8fda91acbe0e6 100644 (file)
@@ -20,6 +20,7 @@
 #include <linux/spi/spi.h>
 #include <linux/slab.h>
 #include <linux/platform_data/atmel.h>
+#include <linux/of.h>
 
 #include <asm/io.h>
 #include <asm/gpio.h>
@@ -768,6 +769,10 @@ static int atmel_spi_setup(struct spi_device *spi)
 
        /* chipselect must have been muxed as GPIO (e.g. in board setup) */
        npcs_pin = (unsigned int)spi->controller_data;
+
+       if (gpio_is_valid(spi->cs_gpio))
+               npcs_pin = spi->cs_gpio;
+
        asd = spi->controller_state;
        if (!asd) {
                asd = kzalloc(sizeof(struct atmel_spi_device), GFP_KERNEL);
@@ -937,8 +942,9 @@ static int atmel_spi_probe(struct platform_device *pdev)
        /* the spi->mode bits understood by this driver: */
        master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
 
+       master->dev.of_node = pdev->dev.of_node;
        master->bus_num = pdev->id;
-       master->num_chipselect = 4;
+       master->num_chipselect = master->dev.of_node ? 0 : 4;
        master->setup = atmel_spi_setup;
        master->transfer = atmel_spi_transfer;
        master->cleanup = atmel_spi_cleanup;
@@ -1064,11 +1070,20 @@ static int atmel_spi_resume(struct platform_device *pdev)
 #define        atmel_spi_resume        NULL
 #endif
 
+#if defined(CONFIG_OF)
+static const struct of_device_id atmel_spi_dt_ids[] = {
+       { .compatible = "atmel,at91rm9200-spi" },
+       { /* sentinel */ }
+};
+
+MODULE_DEVICE_TABLE(of, atmel_spi_dt_ids);
+#endif
 
 static struct platform_driver atmel_spi_driver = {
        .driver         = {
                .name   = "atmel_spi",
                .owner  = THIS_MODULE,
+               .of_match_table = of_match_ptr(atmel_spi_dt_ids),
        },
        .suspend        = atmel_spi_suspend,
        .resume         = atmel_spi_resume,