microblaze: Optimize SAVE_STATE macro

It is necessary to setup BIP and EE and clear EIP
only for unaligned exception handler. The rest of
hw exception handlers don't require it.
HW exception occured and we are not in virtual mode.
That's why we can do operations protected by EIP.
Interrupt, next hw exception or syscall can't occur.

EIP is cleared by rted.

This change speedup page_fault hw exception handler
which is critical path.

There is also necessary to save R11 content before
flag setup for unaligned exception.

Signed-off-by: Michal Simek <monstr@monstr.eu>

diff --git a/arch/microblaze/kernel/entry.S b/arch/microblaze/kernel/entry.S
index 3fee82d6e9a21aaf6170c301340110b69b3ed0f2..04265716518454c27e15cf7e1a9f8f530148c978 100644 (file)
--- a/arch/microblaze/kernel/entry.S
+++ b/arch/microblaze/kernel/entry.S
@@ -507,9 +507,6 @@ C_ENTRY(sys_rt_sigreturn_wrapper):
 #define SAVE_STATE     \
        swi     r1, r0, TOPHYS(PER_CPU(ENTRY_SP)); /* save stack */     \
        swi     r11, r0, TOPHYS(r0_ram + PTO + PT_R11); /* Save r11 */  \
-       set_bip;        /*equalize initial state for all possible entries*/\
-       clear_eip;                                                      \
-       set_ee;                                                         \
        /* See if already in kernel mode.*/                             \
        mfs     r11, rmsr;                                              \
        nop;                                                            \
@@ -569,7 +566,7 @@ C_ENTRY(full_exception_trap):
        nop
        addik   r12, r0, full_exception
        set_vms;
-       rtbd    r12, 0;
+       rted    r12, 0;
        nop;
 
 /*
@@ -583,6 +580,17 @@ C_ENTRY(full_exception_trap):
  * The assembler routine is in "arch/microblaze/kernel/hw_exception_handler.S"
  */
 C_ENTRY(unaligned_data_trap):
+       /* MS: I have to save r11 value and then restore it because
+        * set_bit, clear_eip, set_ee use r11 as temp register if MSR
+        * instructions are not used. We don't need to do if MSR instructions
+        * are used and they use r0 instead of r11.
+        * I am using ENTRY_SP which should be primary used only for stack
+        * pointer saving. */
+       swi     r11, r0, TOPHYS(PER_CPU(ENTRY_SP));
+       set_bip;        /* equalize initial state for all possible entries */
+       clear_eip;
+       set_ee;
+       lwi     r11, r0, TOPHYS(PER_CPU(ENTRY_SP));
        SAVE_STATE              /* Save registers.*/
        /* where the trap should return need -8 to adjust for rtsd r15, 8 */
        addik   r15, r0, ret_from_exc-8
@@ -625,7 +633,7 @@ C_ENTRY(page_fault_data_trap):
        nop
        addik   r12, r0, do_page_fault
        set_vms;
-       rtbd    r12, 0; /* interrupts enabled */
+       rted    r12, 0; /* interrupts enabled */
        nop;
 
 C_ENTRY(page_fault_instr_trap):
@@ -638,7 +646,7 @@ C_ENTRY(page_fault_instr_trap):
        ori     r7, r0, 0               /* parameter unsigned long error_code */
        addik   r12, r0, do_page_fault
        set_vms;
-       rtbd    r12, 0; /* interrupts enabled */
+       rted    r12, 0; /* interrupts enabled */
        nop;
 
 /* Entry point used to return from an exception.  */