i2c-i801: Remove verbose debugging messages

Dumping the register values before and after every transaction was
useful during driver development but now it's only spamming the log.

Signed-off-by: Jean Delvare <khali@linux-fr.org>

diff --git a/drivers/i2c/busses/i2c-i801.c b/drivers/i2c/busses/i2c-i801.c
index 9717ffe12921fc5ffdf16d4035160a93d1eaecab..965905fb5d56220992d4f97a7e248916fe1e1b2f 100644 (file)
--- a/drivers/i2c/busses/i2c-i801.c
+++ b/drivers/i2c/busses/i2c-i801.c
@@ -138,11 +138,6 @@ static int i801_transaction(int xact)
        int result = 0;
        int timeout = 0;
 
-       dev_dbg(&I801_dev->dev, "Transaction (pre): CNT=%02x, CMD=%02x, "
-               "ADD=%02x, DAT0=%02x, DAT1=%02x\n", inb_p(SMBHSTCNT),
-               inb_p(SMBHSTCMD), inb_p(SMBHSTADD), inb_p(SMBHSTDAT0),
-               inb_p(SMBHSTDAT1));
-
        /* Make sure the SMBus host is ready to start transmitting */
        /* 0x1f = Failed, Bus_Err, Dev_Err, Intr, Host_Busy */
        if ((temp = (0x1f & inb_p(SMBHSTSTS))) != 0x00) {
@@ -202,10 +197,6 @@ static int i801_transaction(int xact)
                dev_dbg(&I801_dev->dev, "Failed reset at end of transaction "
                        "(%02x)\n", temp);
        }
-       dev_dbg(&I801_dev->dev, "Transaction (post): CNT=%02x, CMD=%02x, "
-               "ADD=%02x, DAT0=%02x, DAT1=%02x\n", inb_p(SMBHSTCNT),
-               inb_p(SMBHSTCMD), inb_p(SMBHSTADD), inb_p(SMBHSTDAT0),
-               inb_p(SMBHSTDAT1));
        return result;
 }
 
@@ -293,11 +284,6 @@ static int i801_block_transaction_byte_by_byte(union i2c_smbus_data *data,
                }
                outb_p(smbcmd | ENABLE_INT9, SMBHSTCNT);
 
-               dev_dbg(&I801_dev->dev, "Block (pre %d): CNT=%02x, CMD=%02x, "
-                       "ADD=%02x, DAT0=%02x, DAT1=%02x, BLKDAT=%02x\n", i,
-                       inb_p(SMBHSTCNT), inb_p(SMBHSTCMD), inb_p(SMBHSTADD),
-                       inb_p(SMBHSTDAT0), inb_p(SMBHSTDAT1), inb_p(SMBBLKDAT));
-
                /* Make sure the SMBus host is ready to start transmitting */
                temp = inb_p(SMBHSTSTS);
                if (i == 1) {
@@ -381,10 +367,6 @@ static int i801_block_transaction_byte_by_byte(union i2c_smbus_data *data,
                                "Bad status (%02x) at end of transaction\n",
                                temp);
                }
-               dev_dbg(&I801_dev->dev, "Block (post %d): CNT=%02x, CMD=%02x, "
-                       "ADD=%02x, DAT0=%02x, DAT1=%02x, BLKDAT=%02x\n", i,
-                       inb_p(SMBHSTCNT), inb_p(SMBHSTCMD), inb_p(SMBHSTADD),
-                       inb_p(SMBHSTDAT0), inb_p(SMBHSTDAT1), inb_p(SMBBLKDAT));
 
                if (result < 0)
                        return result;