min_addr=nn[KMG] [KNL,BOOT,ia64] All physical memory below this
physical address is ignored.
+ mini2440= [ARM,HW,KNL]
+ Format:[0..2][b][c][t]
+ Default: "0tb"
+ MINI2440 configuration specification:
+ 0 - The attached screen is the 3.5" TFT
+ 1 - The attached screen is the 7" TFT
+ 2 - The VGA Shield is attached (1024x768)
+ Leaving out the screen size parameter will not load
+ the TFT driver, and the framebuffer will be left
+ unconfigured.
+ b - Enable backlight. The TFT backlight pin will be
+ linked to the kernel VESA blanking code and a GPIO
+ LED. This parameter is not necessary when using the
+ VGA shield.
+ c - Enable the s3c camera interface.
+ t - Reserved for enabling touchscreen support. The
+ touchscreen support is not enabled in the mainstream
+ kernel as of 2.6.30, a preliminary port can be found
+ in the "bleeding edge" mini2440 support kernel at
+ http://repo.or.cz/w/linux-2.6/mini2440.git
+
mminit_loglevel=
[KNL] When CONFIG_DEBUG_MEMORY_INIT is set, this
parameter allows control of the logging verbosity for
L: openezx-devel@lists.openezx.org (subscribers-only)
W: http://www.openezx.org/
S: Maintained
+T: topgit git://git.openezx.org/openezx.git
+F: arch/arm/mach-pxa/ezx.c
ARM/FARADAY FA526 PORT
P: Paulius Zaleckas
M: philipp.zabel@gmail.com
S: Maintained
+ARM/MIOA701 MACHINE SUPPORT
+P: Robert Jarzmik
+M: robert.jarzmik@free.fr
+L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
+F: arch/arm/mach-pxa/mioa701.c
+S: Maintained
+
ARM/NEC MOBILEPRO 900/c MACHINE SUPPORT
P: Michael Petchkovsky
M: mkpetch@internode.on.net
S: Maintained
+ARM/OPENMOKO NEO FREERUNNER (GTA02) MACHINE SUPPORT
+P: Nelson Castillo
+M: arhuaco@freaks-unidos.net
+L: openmoko-kernel@lists.openmoko.org (subscribers-only)
+W: http://wiki.openmoko.org/wiki/Neo_FreeRunner
+S: Supported
+
ARM/TOSA MACHINE SUPPORT
P: Dmitry Eremin-Solenikov
M: dbaryshkov@gmail.com
W: http://hackndev.com
S: Maintained
+ARM/PALM TREO 680 SUPPORT
+P: Tomas Cech
+M: sleep_walker@suse.cz
+W: http://hackndev.com
+S: Maintained
+
ARM/PALMZ72 SUPPORT
P: Sergey Lapin
M: slapin@ossfans.org
menu "CPU Power Management"
-if (ARCH_SA1100 || ARCH_INTEGRATOR || ARCH_OMAP || ARCH_PXA)
+if (ARCH_SA1100 || ARCH_INTEGRATOR || ARCH_OMAP || ARCH_PXA || ARCH_S3C64XX)
source "drivers/cpufreq/Kconfig"
default y
select CPU_FREQ_DEFAULT_GOV_USERSPACE
+config CPU_FREQ_S3C64XX
+ bool "CPUfreq support for Samsung S3C64XX CPUs"
+ depends on CPU_FREQ && CPU_S3C6410
+
endif
source "drivers/cpuidle/Kconfig"
b __armv4_mmu_cache_off
b __armv5tej_mmu_cache_flush
+#ifdef CONFIG_CPU_FEROCEON_OLD_ID
+ /* this conflicts with the standard ARMv5TE entry */
+ .long 0x41009260 @ Old Feroceon
+ .long 0xff00fff0
+ b __armv4_mmu_cache_on
+ b __armv4_mmu_cache_off
+ b __armv5tej_mmu_cache_flush
+#endif
+
.word 0x66015261 @ FA526
.word 0xff01fff1
b __fa526_cache_on
u32 val;
spin_lock(&irq_controller_lock);
- irq_desc[irq].cpu = cpu;
+ irq_desc[irq].node = cpu;
val = readl(reg) & ~(0xff << shift);
val |= 1 << (cpu + shift);
writel(val, reg);
{
struct vic_device *v = vic_from_irq(irq);
unsigned int off = irq & 31;
+ u32 bit = 1 << off;
if (!v)
return -EINVAL;
+ if (!(bit & v->resume_sources))
+ return -EINVAL;
+
if (on)
- v->resume_irqs |= 1 << off;
+ v->resume_irqs |= bit;
else
- v->resume_irqs &= ~(1 << off);
+ v->resume_irqs &= ~bit;
return 0;
}
--- /dev/null
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.30-rc6
+# Wed May 20 12:29:51 2009
+#
+CONFIG_ARM=y
+CONFIG_HAVE_PWM=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+CONFIG_GENERIC_GPIO=y
+# CONFIG_GENERIC_TIME is not set
+# CONFIG_GENERIC_CLOCKEVENTS is not set
+CONFIG_MMU=y
+CONFIG_NO_IOPORT=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_LOCKDEP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+# CONFIG_ARCH_HAS_ILOG2_U32 is not set
+# CONFIG_ARCH_HAS_ILOG2_U64 is not set
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
+CONFIG_VECTORS_BASE=0xffff0000
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_POSIX_MQUEUE_SYSCTL=y
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_AUDIT is not set
+
+#
+# RCU Subsystem
+#
+CONFIG_CLASSIC_RCU=y
+# CONFIG_TREE_RCU is not set
+# CONFIG_PREEMPT_RCU is not set
+# CONFIG_TREE_RCU_TRACE is not set
+# CONFIG_PREEMPT_RCU_TRACE is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=17
+# CONFIG_GROUP_SCHED is not set
+# CONFIG_CGROUPS is not set
+# CONFIG_SYSFS_DEPRECATED_V2 is not set
+CONFIG_RELAY=y
+CONFIG_NAMESPACES=y
+CONFIG_UTS_NS=y
+CONFIG_IPC_NS=y
+# CONFIG_USER_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_NET_NS is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_RD_GZIP=y
+CONFIG_RD_BZIP2=y
+CONFIG_RD_LZMA=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL=y
+CONFIG_ANON_INODES=y
+# CONFIG_EMBEDDED is not set
+CONFIG_UID16=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_AIO=y
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLUB_DEBUG=y
+# CONFIG_COMPAT_BRK is not set
+# CONFIG_SLAB is not set
+CONFIG_SLUB=y
+# CONFIG_SLOB is not set
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_KPROBES is not set
+CONFIG_HAVE_KPROBES=y
+CONFIG_HAVE_KRETPROBES=y
+CONFIG_HAVE_CLK=y
+# CONFIG_SLOW_WORK is not set
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_SLABINFO=y
+CONFIG_RT_MUTEXES=y
+CONFIG_BASE_SMALL=0
+CONFIG_MODULES=y
+CONFIG_MODULE_FORCE_LOAD=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_BLOCK=y
+CONFIG_LBD=y
+# CONFIG_BLK_DEV_BSG is not set
+CONFIG_BLK_DEV_INTEGRITY=y
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+CONFIG_FREEZER=y
+
+#
+# System Type
+#
+# CONFIG_ARCH_AAEC2000 is not set
+# CONFIG_ARCH_INTEGRATOR is not set
+# CONFIG_ARCH_REALVIEW is not set
+# CONFIG_ARCH_VERSATILE is not set
+# CONFIG_ARCH_AT91 is not set
+# CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_EBSA110 is not set
+# CONFIG_ARCH_EP93XX is not set
+# CONFIG_ARCH_GEMINI is not set
+# CONFIG_ARCH_FOOTBRIDGE is not set
+# CONFIG_ARCH_NETX is not set
+# CONFIG_ARCH_H720X is not set
+# CONFIG_ARCH_IMX is not set
+# CONFIG_ARCH_IOP13XX is not set
+# CONFIG_ARCH_IOP32X is not set
+# CONFIG_ARCH_IOP33X is not set
+# CONFIG_ARCH_IXP23XX is not set
+# CONFIG_ARCH_IXP2000 is not set
+# CONFIG_ARCH_IXP4XX is not set
+# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_KIRKWOOD is not set
+# CONFIG_ARCH_KS8695 is not set
+# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_LOKI is not set
+# CONFIG_ARCH_MV78XX0 is not set
+# CONFIG_ARCH_MXC is not set
+# CONFIG_ARCH_ORION5X is not set
+# CONFIG_ARCH_PNX4008 is not set
+# CONFIG_ARCH_PXA is not set
+# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_RPC is not set
+# CONFIG_ARCH_SA1100 is not set
+CONFIG_ARCH_S3C2410=y
+# CONFIG_ARCH_S3C64XX is not set
+# CONFIG_ARCH_SHARK is not set
+# CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_DAVINCI is not set
+# CONFIG_ARCH_OMAP is not set
+# CONFIG_ARCH_MSM is not set
+# CONFIG_ARCH_W90X900 is not set
+CONFIG_PLAT_S3C24XX=y
+CONFIG_S3C2410_CLOCK=y
+CONFIG_CPU_S3C244X=y
+CONFIG_S3C24XX_PWM=y
+CONFIG_S3C24XX_GPIO_EXTRA=0
+CONFIG_S3C2410_DMA=y
+# CONFIG_S3C2410_DMA_DEBUG is not set
+CONFIG_S3C24XX_ADC=y
+CONFIG_PLAT_S3C=y
+CONFIG_CPU_LLSERIAL_S3C2440_ONLY=y
+CONFIG_CPU_LLSERIAL_S3C2440=y
+
+#
+# Boot options
+#
+# CONFIG_S3C_BOOT_WATCHDOG is not set
+# CONFIG_S3C_BOOT_ERROR_RESET is not set
+CONFIG_S3C_BOOT_UART_FORCE_FIFO=y
+
+#
+# Power management
+#
+# CONFIG_S3C2410_PM_DEBUG is not set
+# CONFIG_S3C2410_PM_CHECK is not set
+CONFIG_S3C_LOWLEVEL_UART_PORT=0
+CONFIG_S3C_GPIO_SPACE=0
+
+#
+# S3C2400 Machines
+#
+CONFIG_S3C2410_PM=y
+CONFIG_S3C2410_GPIO=y
+
+#
+# S3C2410 Machines
+#
+# CONFIG_ARCH_SMDK2410 is not set
+# CONFIG_ARCH_H1940 is not set
+# CONFIG_MACH_N30 is not set
+# CONFIG_ARCH_BAST is not set
+# CONFIG_MACH_OTOM is not set
+# CONFIG_MACH_AML_M5900 is not set
+# CONFIG_MACH_TCT_HAMMER is not set
+# CONFIG_MACH_VR1000 is not set
+# CONFIG_MACH_QT2410 is not set
+
+#
+# S3C2412 Machines
+#
+# CONFIG_MACH_JIVE is not set
+# CONFIG_MACH_SMDK2413 is not set
+# CONFIG_MACH_SMDK2412 is not set
+# CONFIG_MACH_VSTMS is not set
+CONFIG_CPU_S3C2440=y
+CONFIG_S3C2440_DMA=y
+
+#
+# S3C2440 Machines
+#
+# CONFIG_MACH_ANUBIS is not set
+# CONFIG_MACH_OSIRIS is not set
+# CONFIG_MACH_RX3715 is not set
+# CONFIG_ARCH_S3C2440 is not set
+# CONFIG_MACH_NEXCODER_2440 is not set
+# CONFIG_MACH_AT2440EVB is not set
+CONFIG_MACH_MINI2440=y
+
+#
+# S3C2442 Machines
+#
+
+#
+# S3C2443 Machines
+#
+# CONFIG_MACH_SMDK2443 is not set
+
+#
+# Processor Type
+#
+CONFIG_CPU_32=y
+CONFIG_CPU_ARM920T=y
+CONFIG_CPU_32v4T=y
+CONFIG_CPU_ABRT_EV4T=y
+CONFIG_CPU_PABRT_NOIFAR=y
+CONFIG_CPU_CACHE_V4WT=y
+CONFIG_CPU_CACHE_VIVT=y
+CONFIG_CPU_COPY_V4WB=y
+CONFIG_CPU_TLB_V4WBI=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+
+#
+# Processor Features
+#
+CONFIG_ARM_THUMB=y
+# CONFIG_CPU_ICACHE_DISABLE is not set
+# CONFIG_CPU_DCACHE_DISABLE is not set
+# CONFIG_CPU_DCACHE_WRITETHROUGH is not set
+# CONFIG_OUTER_CACHE is not set
+
+#
+# Bus support
+#
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCCARD is not set
+
+#
+# Kernel Features
+#
+CONFIG_VMSPLIT_3G=y
+# CONFIG_VMSPLIT_2G is not set
+# CONFIG_VMSPLIT_1G is not set
+CONFIG_PAGE_OFFSET=0xC0000000
+# CONFIG_PREEMPT is not set
+CONFIG_HZ=200
+CONFIG_AEABI=y
+# CONFIG_OABI_COMPAT is not set
+CONFIG_ARCH_FLATMEM_HAS_HOLES=y
+# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
+# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
+# CONFIG_HIGHMEM is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_SPLIT_PTLOCK_CPUS=4096
+# CONFIG_PHYS_ADDR_T_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=0
+CONFIG_VIRT_TO_BUS=y
+CONFIG_UNEVICTABLE_LRU=y
+CONFIG_HAVE_MLOCK=y
+CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_ALIGNMENT_TRAP=y
+
+#
+# Boot options
+#
+CONFIG_ZBOOT_ROM_TEXT=0
+CONFIG_ZBOOT_ROM_BSS=0
+CONFIG_CMDLINE=""
+# CONFIG_XIP_KERNEL is not set
+CONFIG_KEXEC=y
+CONFIG_ATAGS_PROC=y
+
+#
+# CPU Power Management
+#
+CONFIG_CPU_IDLE=y
+CONFIG_CPU_IDLE_GOV_LADDER=y
+
+#
+# Floating point emulation
+#
+
+#
+# At least one emulation must be selected
+#
+
+#
+# Userspace binary formats
+#
+CONFIG_BINFMT_ELF=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_HAVE_AOUT=y
+CONFIG_BINFMT_AOUT=m
+CONFIG_BINFMT_MISC=m
+
+#
+# Power management options
+#
+CONFIG_PM=y
+# CONFIG_PM_DEBUG is not set
+CONFIG_PM_SLEEP=y
+CONFIG_SUSPEND=y
+CONFIG_SUSPEND_FREEZER=y
+CONFIG_APM_EMULATION=y
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+CONFIG_PACKET_MMAP=y
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+CONFIG_XFRM_USER=m
+# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_XFRM_STATISTICS is not set
+CONFIG_NET_KEY=m
+# CONFIG_NET_KEY_MIGRATE is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_ASK_IP_FIB_HASH=y
+# CONFIG_IP_FIB_TRIE is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_MULTIPLE_TABLES=y
+CONFIG_IP_ROUTE_MULTIPATH=y
+CONFIG_IP_ROUTE_VERBOSE=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+CONFIG_IP_MROUTE=y
+CONFIG_IP_PIMSM_V1=y
+CONFIG_IP_PIMSM_V2=y
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+CONFIG_INET_DIAG=m
+CONFIG_INET_TCP_DIAG=m
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_NETWORK_SECMARK is not set
+CONFIG_NETFILTER=y
+# CONFIG_NETFILTER_DEBUG is not set
+CONFIG_NETFILTER_ADVANCED=y
+CONFIG_BRIDGE_NETFILTER=y
+
+#
+# Core Netfilter Configuration
+#
+# CONFIG_NETFILTER_NETLINK_QUEUE is not set
+# CONFIG_NETFILTER_NETLINK_LOG is not set
+# CONFIG_NF_CONNTRACK is not set
+# CONFIG_NETFILTER_XTABLES is not set
+# CONFIG_IP_VS is not set
+
+#
+# IP: Netfilter Configuration
+#
+# CONFIG_NF_DEFRAG_IPV4 is not set
+# CONFIG_IP_NF_QUEUE is not set
+# CONFIG_IP_NF_IPTABLES is not set
+# CONFIG_IP_NF_ARPTABLES is not set
+# CONFIG_BRIDGE_NF_EBTABLES is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+CONFIG_STP=m
+CONFIG_GARP=m
+CONFIG_BRIDGE=m
+# CONFIG_NET_DSA is not set
+CONFIG_VLAN_8021Q=m
+CONFIG_VLAN_8021Q_GVRP=y
+# CONFIG_DECNET is not set
+CONFIG_LLC=m
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_PHONET is not set
+# CONFIG_NET_SCHED is not set
+# CONFIG_DCB is not set
+
+#
+# Network testing
+#
+CONFIG_NET_PKTGEN=m
+# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
+# CONFIG_IRDA is not set
+CONFIG_BT=m
+CONFIG_BT_L2CAP=m
+CONFIG_BT_SCO=m
+CONFIG_BT_RFCOMM=m
+CONFIG_BT_RFCOMM_TTY=y
+CONFIG_BT_BNEP=m
+CONFIG_BT_BNEP_MC_FILTER=y
+CONFIG_BT_BNEP_PROTO_FILTER=y
+CONFIG_BT_HIDP=m
+
+#
+# Bluetooth device drivers
+#
+CONFIG_BT_HCIBTUSB=m
+CONFIG_BT_HCIBTSDIO=m
+CONFIG_BT_HCIUART=m
+CONFIG_BT_HCIUART_H4=y
+CONFIG_BT_HCIUART_BCSP=y
+CONFIG_BT_HCIUART_LL=y
+CONFIG_BT_HCIBCM203X=m
+CONFIG_BT_HCIBPA10X=m
+CONFIG_BT_HCIBFUSB=m
+CONFIG_BT_HCIVHCI=m
+# CONFIG_AF_RXRPC is not set
+CONFIG_FIB_RULES=y
+CONFIG_WIRELESS=y
+CONFIG_CFG80211=m
+CONFIG_CFG80211_REG_DEBUG=y
+CONFIG_WIRELESS_OLD_REGULATORY=y
+CONFIG_WIRELESS_EXT=y
+CONFIG_WIRELESS_EXT_SYSFS=y
+CONFIG_LIB80211=m
+CONFIG_LIB80211_CRYPT_WEP=m
+CONFIG_LIB80211_CRYPT_CCMP=m
+CONFIG_LIB80211_CRYPT_TKIP=m
+# CONFIG_LIB80211_DEBUG is not set
+CONFIG_MAC80211=m
+
+#
+# Rate control algorithm selection
+#
+CONFIG_MAC80211_RC_MINSTREL=y
+# CONFIG_MAC80211_RC_DEFAULT_PID is not set
+CONFIG_MAC80211_RC_DEFAULT_MINSTREL=y
+CONFIG_MAC80211_RC_DEFAULT="minstrel"
+CONFIG_MAC80211_MESH=y
+CONFIG_MAC80211_LEDS=y
+# CONFIG_MAC80211_DEBUGFS is not set
+# CONFIG_MAC80211_DEBUG_MENU is not set
+# CONFIG_WIMAX is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+CONFIG_FW_LOADER=y
+# CONFIG_FIRMWARE_IN_KERNEL is not set
+CONFIG_EXTRA_FIRMWARE=""
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+CONFIG_CONNECTOR=m
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+CONFIG_MTD_CONCAT=y
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_TESTS is not set
+# CONFIG_MTD_REDBOOT_PARTS is not set
+CONFIG_MTD_CMDLINE_PARTS=y
+# CONFIG_MTD_AFS_PARTS is not set
+# CONFIG_MTD_AR7_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_FTL=y
+CONFIG_NFTL=y
+CONFIG_NFTL_RW=y
+CONFIG_INFTL=y
+CONFIG_RFD_FTL=y
+# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+CONFIG_MTD_JEDECPROBE=y
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_CFI_STAA=y
+CONFIG_MTD_CFI_UTIL=y
+CONFIG_MTD_RAM=y
+CONFIG_MTD_ROM=y
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+# CONFIG_MTD_ARM_INTEGRATOR is not set
+# CONFIG_MTD_IMPA7 is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_DATAFLASH is not set
+# CONFIG_MTD_M25P80 is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_VERIFY_WRITE=y
+# CONFIG_MTD_NAND_ECC_SMC is not set
+# CONFIG_MTD_NAND_MUSEUM_IDS is not set
+# CONFIG_MTD_NAND_GPIO is not set
+CONFIG_MTD_NAND_IDS=y
+CONFIG_MTD_NAND_S3C2410=y
+# CONFIG_MTD_NAND_S3C2410_DEBUG is not set
+# CONFIG_MTD_NAND_S3C2410_HWECC is not set
+# CONFIG_MTD_NAND_S3C2410_CLKSTOP is not set
+# CONFIG_MTD_NAND_DISKONCHIP is not set
+# CONFIG_MTD_NAND_NANDSIM is not set
+CONFIG_MTD_NAND_PLATFORM=y
+# CONFIG_MTD_ALAUDA is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# LPDDR flash memory drivers
+#
+CONFIG_MTD_LPDDR=y
+CONFIG_MTD_QINFO_PROBE=y
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+# CONFIG_PARPORT is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=m
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+CONFIG_BLK_DEV_NBD=m
+# CONFIG_BLK_DEV_UB is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=65536
+# CONFIG_BLK_DEV_XIP is not set
+CONFIG_CDROM_PKTCDVD=m
+CONFIG_CDROM_PKTCDVD_BUFFERS=8
+# CONFIG_CDROM_PKTCDVD_WCACHE is not set
+# CONFIG_ATA_OVER_ETH is not set
+CONFIG_MISC_DEVICES=y
+# CONFIG_ICS932S401 is not set
+# CONFIG_ENCLOSURE_SERVICES is not set
+# CONFIG_ISL29003 is not set
+# CONFIG_C2PORT is not set
+
+#
+# EEPROM support
+#
+CONFIG_EEPROM_AT24=y
+# CONFIG_EEPROM_AT25 is not set
+# CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_93CX6 is not set
+CONFIG_HAVE_IDE=y
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+CONFIG_SCSI=m
+CONFIG_SCSI_DMA=y
+# CONFIG_SCSI_TGT is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_SCSI_PROC_FS is not set
+
+#
+# SCSI support type (disk, tape, CD-ROM)
+#
+CONFIG_BLK_DEV_SD=m
+# CONFIG_CHR_DEV_ST is not set
+# CONFIG_CHR_DEV_OSST is not set
+# CONFIG_BLK_DEV_SR is not set
+CONFIG_CHR_DEV_SG=m
+# CONFIG_CHR_DEV_SCH is not set
+
+#
+# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
+#
+# CONFIG_SCSI_MULTI_LUN is not set
+# CONFIG_SCSI_CONSTANTS is not set
+# CONFIG_SCSI_LOGGING is not set
+# CONFIG_SCSI_SCAN_ASYNC is not set
+CONFIG_SCSI_WAIT_SCAN=m
+
+#
+# SCSI Transports
+#
+# CONFIG_SCSI_SPI_ATTRS is not set
+# CONFIG_SCSI_FC_ATTRS is not set
+# CONFIG_SCSI_ISCSI_ATTRS is not set
+# CONFIG_SCSI_SAS_LIBSAS is not set
+# CONFIG_SCSI_SRP_ATTRS is not set
+# CONFIG_SCSI_LOWLEVEL is not set
+# CONFIG_SCSI_DH is not set
+# CONFIG_SCSI_OSD_INITIATOR is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+CONFIG_NETDEVICES=y
+CONFIG_COMPAT_NET_DEV_OPS=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+CONFIG_TUN=m
+# CONFIG_VETH is not set
+# CONFIG_PHYLIB is not set
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_AX88796 is not set
+# CONFIG_SMC91X is not set
+CONFIG_DM9000=y
+CONFIG_DM9000_DEBUGLEVEL=4
+# CONFIG_DM9000_FORCE_SIMPLE_PHY_POLL is not set
+# CONFIG_ENC28J60 is not set
+# CONFIG_ETHOC is not set
+# CONFIG_SMC911X is not set
+# CONFIG_SMSC911X is not set
+# CONFIG_DNET is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
+# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
+# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
+# CONFIG_B44 is not set
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+CONFIG_WLAN_80211=y
+CONFIG_LIBERTAS=m
+# CONFIG_LIBERTAS_USB is not set
+CONFIG_LIBERTAS_SDIO=m
+# CONFIG_LIBERTAS_SPI is not set
+# CONFIG_LIBERTAS_DEBUG is not set
+# CONFIG_LIBERTAS_THINFIRM is not set
+# CONFIG_AT76C50X_USB is not set
+# CONFIG_USB_ZD1201 is not set
+# CONFIG_USB_NET_RNDIS_WLAN is not set
+# CONFIG_RTL8187 is not set
+# CONFIG_MAC80211_HWSIM is not set
+# CONFIG_P54_COMMON is not set
+# CONFIG_AR9170_USB is not set
+CONFIG_HOSTAP=m
+CONFIG_HOSTAP_FIRMWARE=y
+CONFIG_HOSTAP_FIRMWARE_NVRAM=y
+# CONFIG_B43 is not set
+# CONFIG_B43LEGACY is not set
+CONFIG_ZD1211RW=m
+CONFIG_ZD1211RW_DEBUG=y
+# CONFIG_RT2X00 is not set
+
+#
+# Enable WiMAX (Networking options) to see the WiMAX drivers
+#
+
+#
+# USB Network Adapters
+#
+# CONFIG_USB_CATC is not set
+# CONFIG_USB_KAWETH is not set
+# CONFIG_USB_PEGASUS is not set
+# CONFIG_USB_RTL8150 is not set
+# CONFIG_USB_USBNET is not set
+# CONFIG_WAN is not set
+CONFIG_PPP=m
+CONFIG_PPP_MULTILINK=y
+CONFIG_PPP_FILTER=y
+CONFIG_PPP_ASYNC=m
+CONFIG_PPP_SYNC_TTY=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_MPPE=m
+# CONFIG_PPPOE is not set
+# CONFIG_PPPOL2TP is not set
+# CONFIG_SLIP is not set
+CONFIG_SLHC=m
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+CONFIG_INPUT_FF_MEMLESS=y
+# CONFIG_INPUT_POLLDEV is not set
+
+#
+# Userland interfaces
+#
+CONFIG_INPUT_MOUSEDEV=y
+CONFIG_INPUT_MOUSEDEV_PSAUX=y
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
+# CONFIG_INPUT_JOYDEV is not set
+CONFIG_INPUT_EVDEV=y
+CONFIG_INPUT_EVBUG=m
+
+#
+# Input Device Drivers
+#
+CONFIG_INPUT_KEYBOARD=y
+# CONFIG_KEYBOARD_ATKBD is not set
+# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_KEYBOARD_LKKBD is not set
+# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_STOWAWAY is not set
+CONFIG_KEYBOARD_GPIO=y
+CONFIG_INPUT_MOUSE=y
+CONFIG_MOUSE_PS2=y
+CONFIG_MOUSE_PS2_ALPS=y
+CONFIG_MOUSE_PS2_LOGIPS2PP=y
+CONFIG_MOUSE_PS2_SYNAPTICS=y
+CONFIG_MOUSE_PS2_TRACKPOINT=y
+# CONFIG_MOUSE_PS2_ELANTECH is not set
+# CONFIG_MOUSE_PS2_TOUCHKIT is not set
+# CONFIG_MOUSE_SERIAL is not set
+# CONFIG_MOUSE_APPLETOUCH is not set
+# CONFIG_MOUSE_BCM5974 is not set
+# CONFIG_MOUSE_VSXXXAA is not set
+# CONFIG_MOUSE_GPIO is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+# CONFIG_TOUCHSCREEN_ADS7846 is not set
+# CONFIG_TOUCHSCREEN_AD7877 is not set
+# CONFIG_TOUCHSCREEN_AD7879_I2C is not set
+# CONFIG_TOUCHSCREEN_AD7879_SPI is not set
+# CONFIG_TOUCHSCREEN_AD7879 is not set
+# CONFIG_TOUCHSCREEN_FUJITSU is not set
+# CONFIG_TOUCHSCREEN_GUNZE is not set
+# CONFIG_TOUCHSCREEN_ELO is not set
+# CONFIG_TOUCHSCREEN_WACOM_W8001 is not set
+# CONFIG_TOUCHSCREEN_MTOUCH is not set
+# CONFIG_TOUCHSCREEN_INEXIO is not set
+# CONFIG_TOUCHSCREEN_MK712 is not set
+# CONFIG_TOUCHSCREEN_PENMOUNT is not set
+# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set
+# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
+# CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set
+# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set
+# CONFIG_TOUCHSCREEN_TSC2007 is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+CONFIG_SERIO=y
+CONFIG_SERIO_SERPORT=y
+CONFIG_SERIO_LIBPS2=y
+CONFIG_SERIO_RAW=y
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
+CONFIG_VT_CONSOLE=y
+CONFIG_HW_CONSOLE=y
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_DEVKMEM=y
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+CONFIG_SERIAL_SAMSUNG=y
+CONFIG_SERIAL_SAMSUNG_UARTS=3
+CONFIG_SERIAL_SAMSUNG_CONSOLE=y
+CONFIG_SERIAL_S3C2440=y
+# CONFIG_SERIAL_MAX3100 is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_UNIX98_PTYS=y
+# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=128
+CONFIG_IPMI_HANDLER=m
+# CONFIG_IPMI_PANIC_EVENT is not set
+CONFIG_IPMI_DEVICE_INTERFACE=m
+CONFIG_IPMI_SI=m
+CONFIG_IPMI_WATCHDOG=m
+CONFIG_IPMI_POWEROFF=m
+CONFIG_HW_RANDOM=y
+# CONFIG_HW_RANDOM_TIMERIOMEM is not set
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_HELPER_AUTO=y
+CONFIG_I2C_ALGOBIT=y
+
+#
+# I2C Hardware Bus support
+#
+
+#
+# I2C system bus drivers (mostly embedded / system-on-chip)
+#
+# CONFIG_I2C_GPIO is not set
+# CONFIG_I2C_OCORES is not set
+CONFIG_I2C_S3C2410=y
+CONFIG_I2C_SIMTEC=y
+
+#
+# External I2C/SMBus adapter drivers
+#
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_TAOS_EVM is not set
+# CONFIG_I2C_TINY_USB is not set
+
+#
+# Other I2C/SMBus bus drivers
+#
+# CONFIG_I2C_PCA_PLATFORM is not set
+# CONFIG_I2C_STUB is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_DS1682 is not set
+# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_PCF8575 is not set
+# CONFIG_SENSORS_PCA9539 is not set
+# CONFIG_SENSORS_MAX6875 is not set
+CONFIG_SENSORS_TSL2550=m
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+CONFIG_SPI=y
+# CONFIG_SPI_DEBUG is not set
+CONFIG_SPI_MASTER=y
+
+#
+# SPI Master Controller Drivers
+#
+CONFIG_SPI_BITBANG=y
+# CONFIG_SPI_GPIO is not set
+CONFIG_SPI_S3C24XX=y
+# CONFIG_SPI_S3C24XX_GPIO is not set
+
+#
+# SPI Protocol Masters
+#
+CONFIG_SPI_SPIDEV=y
+# CONFIG_SPI_TLE62X0 is not set
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_GPIOLIB=y
+# CONFIG_DEBUG_GPIO is not set
+CONFIG_GPIO_SYSFS=y
+
+#
+# Memory mapped GPIO expanders:
+#
+
+#
+# I2C GPIO expanders:
+#
+# CONFIG_GPIO_MAX732X is not set
+# CONFIG_GPIO_PCA953X is not set
+# CONFIG_GPIO_PCF857X is not set
+
+#
+# PCI GPIO expanders:
+#
+
+#
+# SPI GPIO expanders:
+#
+# CONFIG_GPIO_MAX7301 is not set
+# CONFIG_GPIO_MCP23S08 is not set
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+CONFIG_HWMON=y
+# CONFIG_HWMON_VID is not set
+# CONFIG_SENSORS_AD7414 is not set
+# CONFIG_SENSORS_AD7418 is not set
+# CONFIG_SENSORS_ADCXX is not set
+# CONFIG_SENSORS_ADM1021 is not set
+# CONFIG_SENSORS_ADM1025 is not set
+# CONFIG_SENSORS_ADM1026 is not set
+# CONFIG_SENSORS_ADM1029 is not set
+# CONFIG_SENSORS_ADM1031 is not set
+# CONFIG_SENSORS_ADM9240 is not set
+# CONFIG_SENSORS_ADT7462 is not set
+# CONFIG_SENSORS_ADT7470 is not set
+# CONFIG_SENSORS_ADT7473 is not set
+# CONFIG_SENSORS_ADT7475 is not set
+# CONFIG_SENSORS_ATXP1 is not set
+# CONFIG_SENSORS_DS1621 is not set
+# CONFIG_SENSORS_F71805F is not set
+# CONFIG_SENSORS_F71882FG is not set
+# CONFIG_SENSORS_F75375S is not set
+# CONFIG_SENSORS_G760A is not set
+# CONFIG_SENSORS_GL518SM is not set
+# CONFIG_SENSORS_GL520SM is not set
+# CONFIG_SENSORS_IBMAEM is not set
+# CONFIG_SENSORS_IBMPEX is not set
+# CONFIG_SENSORS_IT87 is not set
+# CONFIG_SENSORS_LM63 is not set
+# CONFIG_SENSORS_LM70 is not set
+CONFIG_SENSORS_LM75=y
+# CONFIG_SENSORS_LM77 is not set
+# CONFIG_SENSORS_LM78 is not set
+# CONFIG_SENSORS_LM80 is not set
+# CONFIG_SENSORS_LM83 is not set
+# CONFIG_SENSORS_LM85 is not set
+# CONFIG_SENSORS_LM87 is not set
+# CONFIG_SENSORS_LM90 is not set
+# CONFIG_SENSORS_LM92 is not set
+# CONFIG_SENSORS_LM93 is not set
+# CONFIG_SENSORS_LTC4215 is not set
+# CONFIG_SENSORS_LTC4245 is not set
+# CONFIG_SENSORS_LM95241 is not set
+# CONFIG_SENSORS_MAX1111 is not set
+# CONFIG_SENSORS_MAX1619 is not set
+# CONFIG_SENSORS_MAX6650 is not set
+# CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_PCF8591 is not set
+# CONFIG_SENSORS_SHT15 is not set
+# CONFIG_SENSORS_DME1737 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+# CONFIG_SENSORS_SMSC47M192 is not set
+# CONFIG_SENSORS_SMSC47B397 is not set
+# CONFIG_SENSORS_ADS7828 is not set
+# CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_SENSORS_W83781D is not set
+# CONFIG_SENSORS_W83791D is not set
+# CONFIG_SENSORS_W83792D is not set
+# CONFIG_SENSORS_W83793 is not set
+# CONFIG_SENSORS_W83L785TS is not set
+# CONFIG_SENSORS_W83L786NG is not set
+# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
+# CONFIG_SENSORS_LIS3_SPI is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+CONFIG_THERMAL=m
+# CONFIG_THERMAL_HWMON is not set
+CONFIG_WATCHDOG=y
+# CONFIG_WATCHDOG_NOWAYOUT is not set
+
+#
+# Watchdog Device Drivers
+#
+# CONFIG_SOFT_WATCHDOG is not set
+CONFIG_S3C2410_WATCHDOG=y
+
+#
+# USB-based Watchdog Cards
+#
+# CONFIG_USBPCWATCHDOG is not set
+CONFIG_SSB_POSSIBLE=y
+
+#
+# Sonics Silicon Backplane
+#
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_CORE is not set
+# CONFIG_MFD_SM501 is not set
+# CONFIG_MFD_ASIC3 is not set
+# CONFIG_HTC_EGPIO is not set
+# CONFIG_HTC_PASIC3 is not set
+# CONFIG_TPS65010 is not set
+# CONFIG_TWL4030_CORE is not set
+# CONFIG_MFD_TMIO is not set
+# CONFIG_MFD_T7L66XB is not set
+# CONFIG_MFD_TC6387XB is not set
+# CONFIG_MFD_TC6393XB is not set
+# CONFIG_PMIC_DA903X is not set
+# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM8350_I2C is not set
+# CONFIG_MFD_PCF50633 is not set
+
+#
+# Multimedia devices
+#
+
+#
+# Multimedia core support
+#
+CONFIG_VIDEO_DEV=m
+CONFIG_VIDEO_V4L2_COMMON=m
+CONFIG_VIDEO_ALLOW_V4L1=y
+CONFIG_VIDEO_V4L1_COMPAT=y
+CONFIG_DVB_CORE=m
+CONFIG_VIDEO_MEDIA=m
+
+#
+# Multimedia drivers
+#
+# CONFIG_MEDIA_ATTACH is not set
+CONFIG_MEDIA_TUNER=m
+# CONFIG_MEDIA_TUNER_CUSTOMISE is not set
+CONFIG_MEDIA_TUNER_SIMPLE=m
+CONFIG_MEDIA_TUNER_TDA8290=m
+CONFIG_MEDIA_TUNER_TDA9887=m
+CONFIG_MEDIA_TUNER_TEA5761=m
+CONFIG_MEDIA_TUNER_TEA5767=m
+CONFIG_MEDIA_TUNER_MT20XX=m
+CONFIG_MEDIA_TUNER_XC2028=m
+CONFIG_MEDIA_TUNER_XC5000=m
+CONFIG_MEDIA_TUNER_MC44S803=m
+CONFIG_VIDEO_V4L2=m
+CONFIG_VIDEO_V4L1=m
+CONFIG_VIDEOBUF_GEN=m
+CONFIG_VIDEO_CAPTURE_DRIVERS=y
+# CONFIG_VIDEO_ADV_DEBUG is not set
+# CONFIG_VIDEO_FIXED_MINOR_RANGES is not set
+CONFIG_VIDEO_HELPER_CHIPS_AUTO=y
+# CONFIG_VIDEO_VIVI is not set
+# CONFIG_VIDEO_CPIA is not set
+# CONFIG_VIDEO_CPIA2 is not set
+# CONFIG_VIDEO_SAA5246A is not set
+# CONFIG_VIDEO_SAA5249 is not set
+# CONFIG_VIDEO_AU0828 is not set
+CONFIG_SOC_CAMERA=m
+# CONFIG_SOC_CAMERA_MT9M001 is not set
+# CONFIG_SOC_CAMERA_MT9M111 is not set
+# CONFIG_SOC_CAMERA_MT9T031 is not set
+# CONFIG_SOC_CAMERA_MT9V022 is not set
+# CONFIG_SOC_CAMERA_TW9910 is not set
+CONFIG_SOC_CAMERA_PLATFORM=m
+# CONFIG_SOC_CAMERA_OV772X is not set
+# CONFIG_VIDEO_SH_MOBILE_CEU is not set
+CONFIG_V4L_USB_DRIVERS=y
+# CONFIG_USB_VIDEO_CLASS is not set
+CONFIG_USB_VIDEO_CLASS_INPUT_EVDEV=y
+CONFIG_USB_GSPCA=m
+# CONFIG_USB_M5602 is not set
+# CONFIG_USB_STV06XX is not set
+# CONFIG_USB_GSPCA_CONEX is not set
+# CONFIG_USB_GSPCA_ETOMS is not set
+# CONFIG_USB_GSPCA_FINEPIX is not set
+# CONFIG_USB_GSPCA_MARS is not set
+# CONFIG_USB_GSPCA_MR97310A is not set
+# CONFIG_USB_GSPCA_OV519 is not set
+# CONFIG_USB_GSPCA_OV534 is not set
+# CONFIG_USB_GSPCA_PAC207 is not set
+# CONFIG_USB_GSPCA_PAC7311 is not set
+# CONFIG_USB_GSPCA_SONIXB is not set
+# CONFIG_USB_GSPCA_SONIXJ is not set
+# CONFIG_USB_GSPCA_SPCA500 is not set
+# CONFIG_USB_GSPCA_SPCA501 is not set
+# CONFIG_USB_GSPCA_SPCA505 is not set
+# CONFIG_USB_GSPCA_SPCA506 is not set
+# CONFIG_USB_GSPCA_SPCA508 is not set
+# CONFIG_USB_GSPCA_SPCA561 is not set
+# CONFIG_USB_GSPCA_SQ905 is not set
+# CONFIG_USB_GSPCA_SQ905C is not set
+# CONFIG_USB_GSPCA_STK014 is not set
+# CONFIG_USB_GSPCA_SUNPLUS is not set
+# CONFIG_USB_GSPCA_T613 is not set
+# CONFIG_USB_GSPCA_TV8532 is not set
+# CONFIG_USB_GSPCA_VC032X is not set
+CONFIG_USB_GSPCA_ZC3XX=m
+# CONFIG_VIDEO_PVRUSB2 is not set
+# CONFIG_VIDEO_HDPVR is not set
+# CONFIG_VIDEO_EM28XX is not set
+# CONFIG_VIDEO_CX231XX is not set
+# CONFIG_VIDEO_USBVISION is not set
+# CONFIG_USB_VICAM is not set
+# CONFIG_USB_IBMCAM is not set
+# CONFIG_USB_KONICAWC is not set
+# CONFIG_USB_QUICKCAM_MESSENGER is not set
+# CONFIG_USB_ET61X251 is not set
+# CONFIG_VIDEO_OVCAMCHIP is not set
+# CONFIG_USB_OV511 is not set
+# CONFIG_USB_SE401 is not set
+# CONFIG_USB_SN9C102 is not set
+# CONFIG_USB_STV680 is not set
+# CONFIG_USB_ZC0301 is not set
+# CONFIG_USB_PWC is not set
+# CONFIG_USB_PWC_INPUT_EVDEV is not set
+# CONFIG_USB_ZR364XX is not set
+# CONFIG_USB_STKWEBCAM is not set
+# CONFIG_USB_S2255 is not set
+CONFIG_RADIO_ADAPTERS=y
+# CONFIG_USB_DSBR is not set
+# CONFIG_USB_SI470X is not set
+# CONFIG_USB_MR800 is not set
+# CONFIG_RADIO_TEA5764 is not set
+# CONFIG_DVB_DYNAMIC_MINORS is not set
+CONFIG_DVB_CAPTURE_DRIVERS=y
+# CONFIG_TTPCI_EEPROM is not set
+
+#
+# Supported USB Adapters
+#
+# CONFIG_DVB_USB is not set
+# CONFIG_DVB_SIANO_SMS1XXX is not set
+
+#
+# Supported FlexCopII (B2C2) Adapters
+#
+# CONFIG_DVB_B2C2_FLEXCOP is not set
+
+#
+# Supported DVB Frontends
+#
+# CONFIG_DVB_FE_CUSTOMISE is not set
+# CONFIG_DAB is not set
+
+#
+# Graphics support
+#
+# CONFIG_VGASTATE is not set
+CONFIG_VIDEO_OUTPUT_CONTROL=y
+CONFIG_FB=y
+CONFIG_FIRMWARE_EDID=y
+# CONFIG_FB_DDC is not set
+# CONFIG_FB_BOOT_VESA_SUPPORT is not set
+CONFIG_FB_CFB_FILLRECT=y
+CONFIG_FB_CFB_COPYAREA=y
+CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_FOREIGN_ENDIAN is not set
+# CONFIG_FB_SYS_FOPS is not set
+# CONFIG_FB_SVGALIB is not set
+# CONFIG_FB_MACMODES is not set
+# CONFIG_FB_BACKLIGHT is not set
+CONFIG_FB_MODE_HELPERS=y
+CONFIG_FB_TILEBLITTING=y
+
+#
+# Frame buffer hardware drivers
+#
+# CONFIG_FB_UVESA is not set
+# CONFIG_FB_S1D13XXX is not set
+CONFIG_FB_S3C2410=y
+# CONFIG_FB_S3C2410_DEBUG is not set
+# CONFIG_FB_VIRTUAL is not set
+# CONFIG_FB_METRONOME is not set
+# CONFIG_FB_MB862XX is not set
+# CONFIG_FB_BROADSHEET is not set
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+CONFIG_LCD_CLASS_DEVICE=y
+# CONFIG_LCD_LTV350QV is not set
+# CONFIG_LCD_ILI9320 is not set
+# CONFIG_LCD_TDO24M is not set
+# CONFIG_LCD_VGG2432A4 is not set
+CONFIG_LCD_PLATFORM=y
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+# CONFIG_BACKLIGHT_GENERIC is not set
+CONFIG_BACKLIGHT_PWM=y
+
+#
+# Display device support
+#
+CONFIG_DISPLAY_SUPPORT=y
+
+#
+# Display hardware drivers
+#
+
+#
+# Console display driver support
+#
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_DUMMY_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
+CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
+CONFIG_FONTS=y
+CONFIG_FONT_8x8=y
+# CONFIG_FONT_8x16 is not set
+# CONFIG_FONT_6x11 is not set
+# CONFIG_FONT_7x14 is not set
+# CONFIG_FONT_PEARL_8x8 is not set
+# CONFIG_FONT_ACORN_8x8 is not set
+CONFIG_FONT_MINI_4x6=y
+# CONFIG_FONT_SUN8x16 is not set
+# CONFIG_FONT_SUN12x22 is not set
+# CONFIG_FONT_10x18 is not set
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_MONO is not set
+# CONFIG_LOGO_LINUX_VGA16 is not set
+CONFIG_LOGO_LINUX_CLUT224=y
+CONFIG_SOUND=y
+CONFIG_SOUND_OSS_CORE=y
+CONFIG_SND=y
+CONFIG_SND_TIMER=y
+CONFIG_SND_PCM=y
+CONFIG_SND_HWDEP=m
+CONFIG_SND_RAWMIDI=m
+CONFIG_SND_JACK=y
+CONFIG_SND_SEQUENCER=m
+CONFIG_SND_SEQ_DUMMY=m
+CONFIG_SND_OSSEMUL=y
+CONFIG_SND_MIXER_OSS=m
+CONFIG_SND_PCM_OSS=m
+CONFIG_SND_PCM_OSS_PLUGINS=y
+CONFIG_SND_SEQUENCER_OSS=y
+CONFIG_SND_DYNAMIC_MINORS=y
+CONFIG_SND_SUPPORT_OLD_API=y
+CONFIG_SND_VERBOSE_PROCFS=y
+# CONFIG_SND_VERBOSE_PRINTK is not set
+# CONFIG_SND_DEBUG is not set
+# CONFIG_SND_DRIVERS is not set
+# CONFIG_SND_ARM is not set
+# CONFIG_SND_SPI is not set
+CONFIG_SND_USB=y
+CONFIG_SND_USB_AUDIO=m
+CONFIG_SND_USB_CAIAQ=m
+CONFIG_SND_USB_CAIAQ_INPUT=y
+CONFIG_SND_SOC=y
+CONFIG_SND_S3C24XX_SOC=y
+CONFIG_SND_S3C24XX_SOC_I2S=y
+# CONFIG_SND_S3C24XX_SOC_LN2440SBC_ALC650 is not set
+CONFIG_SND_S3C24XX_SOC_S3C24XX_UDA134X=y
+CONFIG_SND_SOC_I2C_AND_SPI=y
+# CONFIG_SND_SOC_ALL_CODECS is not set
+CONFIG_SND_SOC_L3=y
+CONFIG_SND_SOC_UDA134X=y
+# CONFIG_SOUND_PRIME is not set
+CONFIG_HID_SUPPORT=y
+CONFIG_HID=y
+# CONFIG_HID_DEBUG is not set
+CONFIG_HIDRAW=y
+
+#
+# USB Input Devices
+#
+CONFIG_USB_HID=y
+CONFIG_HID_PID=y
+CONFIG_USB_HIDDEV=y
+
+#
+# Special HID drivers
+#
+CONFIG_HID_A4TECH=y
+CONFIG_HID_APPLE=y
+CONFIG_HID_BELKIN=y
+CONFIG_HID_CHERRY=y
+CONFIG_HID_CHICONY=y
+CONFIG_HID_CYPRESS=y
+# CONFIG_DRAGONRISE_FF is not set
+CONFIG_HID_EZKEY=y
+CONFIG_HID_KYE=y
+CONFIG_HID_GYRATION=y
+CONFIG_HID_KENSINGTON=y
+CONFIG_HID_LOGITECH=y
+# CONFIG_LOGITECH_FF is not set
+# CONFIG_LOGIRUMBLEPAD2_FF is not set
+CONFIG_HID_MICROSOFT=y
+CONFIG_HID_MONTEREY=y
+CONFIG_HID_NTRIG=y
+CONFIG_HID_PANTHERLORD=y
+# CONFIG_PANTHERLORD_FF is not set
+CONFIG_HID_PETALYNX=y
+CONFIG_HID_SAMSUNG=y
+CONFIG_HID_SONY=y
+CONFIG_HID_SUNPLUS=y
+# CONFIG_GREENASIA_FF is not set
+CONFIG_HID_TOPSEED=y
+# CONFIG_THRUSTMASTER_FF is not set
+# CONFIG_ZEROPLUS_FF is not set
+CONFIG_USB_SUPPORT=y
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+# CONFIG_USB_ARCH_HAS_EHCI is not set
+CONFIG_USB=y
+# CONFIG_USB_DEBUG is not set
+# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set
+
+#
+# Miscellaneous USB options
+#
+CONFIG_USB_DEVICEFS=y
+# CONFIG_USB_DEVICE_CLASS is not set
+# CONFIG_USB_DYNAMIC_MINORS is not set
+# CONFIG_USB_SUSPEND is not set
+# CONFIG_USB_OTG is not set
+# CONFIG_USB_MON is not set
+# CONFIG_USB_WUSB is not set
+# CONFIG_USB_WUSB_CBAF is not set
+
+#
+# USB Host Controller Drivers
+#
+# CONFIG_USB_C67X00_HCD is not set
+# CONFIG_USB_OXU210HP_HCD is not set
+# CONFIG_USB_ISP116X_HCD is not set
+# CONFIG_USB_ISP1760_HCD is not set
+CONFIG_USB_OHCI_HCD=y
+# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
+# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
+CONFIG_USB_OHCI_LITTLE_ENDIAN=y
+# CONFIG_USB_SL811_HCD is not set
+# CONFIG_USB_R8A66597_HCD is not set
+# CONFIG_USB_HWA_HCD is not set
+# CONFIG_USB_MUSB_HDRC is not set
+# CONFIG_USB_GADGET_MUSB_HDRC is not set
+
+#
+# USB Device Class drivers
+#
+CONFIG_USB_ACM=m
+# CONFIG_USB_PRINTER is not set
+CONFIG_USB_WDM=m
+# CONFIG_USB_TMC is not set
+
+#
+# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may
+#
+
+#
+# also be needed; see USB_STORAGE Help for more info
+#
+CONFIG_USB_STORAGE=m
+# CONFIG_USB_STORAGE_DEBUG is not set
+CONFIG_USB_STORAGE_DATAFAB=m
+# CONFIG_USB_STORAGE_FREECOM is not set
+CONFIG_USB_STORAGE_ISD200=m
+CONFIG_USB_STORAGE_USBAT=m
+CONFIG_USB_STORAGE_SDDR09=m
+CONFIG_USB_STORAGE_SDDR55=m
+CONFIG_USB_STORAGE_JUMPSHOT=m
+CONFIG_USB_STORAGE_ALAUDA=m
+# CONFIG_USB_STORAGE_ONETOUCH is not set
+# CONFIG_USB_STORAGE_KARMA is not set
+# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
+CONFIG_USB_LIBUSUAL=y
+
+#
+# USB Imaging devices
+#
+# CONFIG_USB_MDC800 is not set
+# CONFIG_USB_MICROTEK is not set
+
+#
+# USB port drivers
+#
+CONFIG_USB_SERIAL=m
+# CONFIG_USB_EZUSB is not set
+# CONFIG_USB_SERIAL_GENERIC is not set
+# CONFIG_USB_SERIAL_AIRCABLE is not set
+# CONFIG_USB_SERIAL_ARK3116 is not set
+# CONFIG_USB_SERIAL_BELKIN is not set
+# CONFIG_USB_SERIAL_CH341 is not set
+# CONFIG_USB_SERIAL_WHITEHEAT is not set
+# CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set
+CONFIG_USB_SERIAL_CP210X=m
+# CONFIG_USB_SERIAL_CYPRESS_M8 is not set
+# CONFIG_USB_SERIAL_EMPEG is not set
+CONFIG_USB_SERIAL_FTDI_SIO=m
+# CONFIG_USB_SERIAL_FUNSOFT is not set
+# CONFIG_USB_SERIAL_VISOR is not set
+# CONFIG_USB_SERIAL_IPAQ is not set
+# CONFIG_USB_SERIAL_IR is not set
+# CONFIG_USB_SERIAL_EDGEPORT is not set
+# CONFIG_USB_SERIAL_EDGEPORT_TI is not set
+# CONFIG_USB_SERIAL_GARMIN is not set
+# CONFIG_USB_SERIAL_IPW is not set
+# CONFIG_USB_SERIAL_IUU is not set
+# CONFIG_USB_SERIAL_KEYSPAN_PDA is not set
+# CONFIG_USB_SERIAL_KEYSPAN is not set
+# CONFIG_USB_SERIAL_KLSI is not set
+# CONFIG_USB_SERIAL_KOBIL_SCT is not set
+# CONFIG_USB_SERIAL_MCT_U232 is not set
+# CONFIG_USB_SERIAL_MOS7720 is not set
+# CONFIG_USB_SERIAL_MOS7840 is not set
+# CONFIG_USB_SERIAL_MOTOROLA is not set
+# CONFIG_USB_SERIAL_NAVMAN is not set
+# CONFIG_USB_SERIAL_PL2303 is not set
+# CONFIG_USB_SERIAL_OTI6858 is not set
+# CONFIG_USB_SERIAL_QUALCOMM is not set
+CONFIG_USB_SERIAL_SPCP8X5=m
+# CONFIG_USB_SERIAL_HP4X is not set
+# CONFIG_USB_SERIAL_SAFE is not set
+# CONFIG_USB_SERIAL_SIEMENS_MPI is not set
+# CONFIG_USB_SERIAL_SIERRAWIRELESS is not set
+# CONFIG_USB_SERIAL_SYMBOL is not set
+# CONFIG_USB_SERIAL_TI is not set
+# CONFIG_USB_SERIAL_CYBERJACK is not set
+# CONFIG_USB_SERIAL_XIRCOM is not set
+# CONFIG_USB_SERIAL_OPTION is not set
+# CONFIG_USB_SERIAL_OMNINET is not set
+# CONFIG_USB_SERIAL_OPTICON is not set
+# CONFIG_USB_SERIAL_DEBUG is not set
+
+#
+# USB Miscellaneous drivers
+#
+# CONFIG_USB_EMI62 is not set
+# CONFIG_USB_EMI26 is not set
+# CONFIG_USB_ADUTUX is not set
+# CONFIG_USB_SEVSEG is not set
+# CONFIG_USB_RIO500 is not set
+# CONFIG_USB_LEGOTOWER is not set
+# CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
+# CONFIG_USB_LED is not set
+# CONFIG_USB_CYPRESS_CY7C63 is not set
+# CONFIG_USB_CYTHERM is not set
+# CONFIG_USB_IDMOUSE is not set
+# CONFIG_USB_FTDI_ELAN is not set
+# CONFIG_USB_APPLEDISPLAY is not set
+# CONFIG_USB_LD is not set
+# CONFIG_USB_TRANCEVIBRATOR is not set
+# CONFIG_USB_IOWARRIOR is not set
+# CONFIG_USB_TEST is not set
+# CONFIG_USB_ISIGHTFW is not set
+# CONFIG_USB_VST is not set
+CONFIG_USB_GADGET=y
+# CONFIG_USB_GADGET_DEBUG is not set
+# CONFIG_USB_GADGET_DEBUG_FILES is not set
+# CONFIG_USB_GADGET_DEBUG_FS is not set
+CONFIG_USB_GADGET_VBUS_DRAW=2
+CONFIG_USB_GADGET_SELECTED=y
+# CONFIG_USB_GADGET_AT91 is not set
+# CONFIG_USB_GADGET_ATMEL_USBA is not set
+# CONFIG_USB_GADGET_FSL_USB2 is not set
+# CONFIG_USB_GADGET_LH7A40X is not set
+# CONFIG_USB_GADGET_OMAP is not set
+# CONFIG_USB_GADGET_PXA25X is not set
+# CONFIG_USB_GADGET_PXA27X is not set
+CONFIG_USB_GADGET_S3C2410=y
+CONFIG_USB_S3C2410=y
+# CONFIG_USB_S3C2410_DEBUG is not set
+# CONFIG_USB_GADGET_IMX is not set
+# CONFIG_USB_GADGET_M66592 is not set
+# CONFIG_USB_GADGET_AMD5536UDC is not set
+# CONFIG_USB_GADGET_FSL_QE is not set
+# CONFIG_USB_GADGET_CI13XXX is not set
+# CONFIG_USB_GADGET_NET2280 is not set
+# CONFIG_USB_GADGET_GOKU is not set
+# CONFIG_USB_GADGET_DUMMY_HCD is not set
+# CONFIG_USB_GADGET_DUALSPEED is not set
+CONFIG_USB_ZERO=m
+CONFIG_USB_ETH=m
+CONFIG_USB_ETH_RNDIS=y
+CONFIG_USB_GADGETFS=m
+CONFIG_USB_FILE_STORAGE=m
+# CONFIG_USB_FILE_STORAGE_TEST is not set
+CONFIG_USB_G_SERIAL=m
+# CONFIG_USB_MIDI_GADGET is not set
+# CONFIG_USB_G_PRINTER is not set
+CONFIG_USB_CDC_COMPOSITE=m
+
+#
+# OTG and related infrastructure
+#
+# CONFIG_USB_GPIO_VBUS is not set
+# CONFIG_NOP_USB_XCEIV is not set
+CONFIG_MMC=y
+# CONFIG_MMC_DEBUG is not set
+# CONFIG_MMC_UNSAFE_RESUME is not set
+
+#
+# MMC/SD/SDIO Card Drivers
+#
+CONFIG_MMC_BLOCK=y
+CONFIG_MMC_BLOCK_BOUNCE=y
+CONFIG_SDIO_UART=y
+# CONFIG_MMC_TEST is not set
+
+#
+# MMC/SD/SDIO Host Controller Drivers
+#
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SPI=y
+CONFIG_MMC_S3C=y
+# CONFIG_MEMSTICK is not set
+# CONFIG_ACCESSIBILITY is not set
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+
+#
+# LED drivers
+#
+CONFIG_LEDS_S3C24XX=y
+# CONFIG_LEDS_PCA9532 is not set
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_GPIO_PLATFORM=y
+# CONFIG_LEDS_LP5521 is not set
+# CONFIG_LEDS_PCA955X is not set
+# CONFIG_LEDS_DAC124S085 is not set
+# CONFIG_LEDS_PWM is not set
+# CONFIG_LEDS_BD2802 is not set
+
+#
+# LED Triggers
+#
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_BACKLIGHT=y
+CONFIG_LEDS_TRIGGER_GPIO=y
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
+
+#
+# iptables trigger is under Netfilter config (LED target)
+#
+CONFIG_RTC_LIB=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_HCTOSYS=y
+CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
+# CONFIG_RTC_DEBUG is not set
+
+#
+# RTC interfaces
+#
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
+CONFIG_RTC_INTF_DEV_UIE_EMUL=y
+# CONFIG_RTC_DRV_TEST is not set
+
+#
+# I2C RTC drivers
+#
+# CONFIG_RTC_DRV_DS1307 is not set
+# CONFIG_RTC_DRV_DS1374 is not set
+# CONFIG_RTC_DRV_DS1672 is not set
+# CONFIG_RTC_DRV_MAX6900 is not set
+# CONFIG_RTC_DRV_RS5C372 is not set
+# CONFIG_RTC_DRV_ISL1208 is not set
+# CONFIG_RTC_DRV_X1205 is not set
+# CONFIG_RTC_DRV_PCF8563 is not set
+# CONFIG_RTC_DRV_PCF8583 is not set
+# CONFIG_RTC_DRV_M41T80 is not set
+# CONFIG_RTC_DRV_S35390A is not set
+# CONFIG_RTC_DRV_FM3130 is not set
+# CONFIG_RTC_DRV_RX8581 is not set
+
+#
+# SPI RTC drivers
+#
+# CONFIG_RTC_DRV_M41T94 is not set
+# CONFIG_RTC_DRV_DS1305 is not set
+# CONFIG_RTC_DRV_DS1390 is not set
+# CONFIG_RTC_DRV_MAX6902 is not set
+# CONFIG_RTC_DRV_R9701 is not set
+# CONFIG_RTC_DRV_RS5C348 is not set
+# CONFIG_RTC_DRV_DS3234 is not set
+
+#
+# Platform RTC drivers
+#
+# CONFIG_RTC_DRV_CMOS is not set
+# CONFIG_RTC_DRV_DS1286 is not set
+# CONFIG_RTC_DRV_DS1511 is not set
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_M48T35 is not set
+# CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_BQ4802 is not set
+# CONFIG_RTC_DRV_V3020 is not set
+
+#
+# on-CPU RTC drivers
+#
+CONFIG_RTC_DRV_S3C=y
+CONFIG_DMADEVICES=y
+
+#
+# DMA Devices
+#
+# CONFIG_AUXDISPLAY is not set
+# CONFIG_REGULATOR is not set
+# CONFIG_UIO is not set
+# CONFIG_STAGING is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=m
+CONFIG_EXT2_FS_XATTR=y
+CONFIG_EXT2_FS_POSIX_ACL=y
+CONFIG_EXT2_FS_SECURITY=y
+# CONFIG_EXT2_FS_XIP is not set
+CONFIG_EXT3_FS=y
+# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
+CONFIG_EXT3_FS_XATTR=y
+CONFIG_EXT3_FS_POSIX_ACL=y
+CONFIG_EXT3_FS_SECURITY=y
+# CONFIG_EXT4_FS is not set
+CONFIG_JBD=y
+# CONFIG_JBD_DEBUG is not set
+CONFIG_FS_MBCACHE=y
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+CONFIG_FS_POSIX_ACL=y
+CONFIG_FILE_LOCKING=y
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_BTRFS_FS is not set
+CONFIG_DNOTIFY=y
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+CONFIG_AUTOFS_FS=y
+CONFIG_AUTOFS4_FS=y
+# CONFIG_FUSE_FS is not set
+CONFIG_GENERIC_ACL=y
+
+#
+# Caches
+#
+# CONFIG_FSCACHE is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+CONFIG_FAT_FS=y
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_CODEPAGE=437
+CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+# CONFIG_HUGETLB_PAGE is not set
+CONFIG_CONFIGFS_FS=m
+CONFIG_MISC_FILESYSTEMS=y
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_ECRYPT_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+# CONFIG_JFFS2_FS_WBUF_VERIFY is not set
+# CONFIG_JFFS2_SUMMARY is not set
+# CONFIG_JFFS2_FS_XATTR is not set
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_ZLIB=y
+# CONFIG_JFFS2_LZO is not set
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
+CONFIG_CRAMFS=y
+# CONFIG_SQUASHFS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+CONFIG_ROMFS_FS=y
+# CONFIG_ROMFS_BACKED_BY_BLOCK is not set
+# CONFIG_ROMFS_BACKED_BY_MTD is not set
+CONFIG_ROMFS_BACKED_BY_BOTH=y
+CONFIG_ROMFS_ON_BLOCK=y
+CONFIG_ROMFS_ON_MTD=y
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+# CONFIG_NILFS2_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFS_V4=y
+CONFIG_ROOT_NFS=y
+# CONFIG_NFSD is not set
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_ACL_SUPPORT=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+CONFIG_SUNRPC_GSS=y
+CONFIG_RPCSEC_GSS_KRB5=y
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+CONFIG_MSDOS_PARTITION=y
+CONFIG_BSD_DISKLABEL=y
+CONFIG_MINIX_SUBPARTITION=y
+CONFIG_SOLARIS_X86_PARTITION=y
+CONFIG_UNIXWARE_DISKLABEL=y
+CONFIG_LDM_PARTITION=y
+# CONFIG_LDM_DEBUG is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
+CONFIG_EFI_PARTITION=y
+# CONFIG_SYSV68_PARTITION is not set
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="cp437"
+CONFIG_NLS_CODEPAGE_437=m
+CONFIG_NLS_CODEPAGE_737=m
+CONFIG_NLS_CODEPAGE_775=m
+CONFIG_NLS_CODEPAGE_850=m
+CONFIG_NLS_CODEPAGE_852=m
+CONFIG_NLS_CODEPAGE_855=m
+CONFIG_NLS_CODEPAGE_857=m
+CONFIG_NLS_CODEPAGE_860=m
+CONFIG_NLS_CODEPAGE_861=m
+CONFIG_NLS_CODEPAGE_862=m
+CONFIG_NLS_CODEPAGE_863=m
+CONFIG_NLS_CODEPAGE_864=m
+CONFIG_NLS_CODEPAGE_865=m
+CONFIG_NLS_CODEPAGE_866=m
+CONFIG_NLS_CODEPAGE_869=m
+CONFIG_NLS_CODEPAGE_936=m
+CONFIG_NLS_CODEPAGE_950=m
+CONFIG_NLS_CODEPAGE_932=m
+CONFIG_NLS_CODEPAGE_949=m
+CONFIG_NLS_CODEPAGE_874=m
+CONFIG_NLS_ISO8859_8=m
+CONFIG_NLS_CODEPAGE_1250=m
+CONFIG_NLS_CODEPAGE_1251=m
+CONFIG_NLS_ASCII=m
+CONFIG_NLS_ISO8859_1=m
+CONFIG_NLS_ISO8859_2=m
+CONFIG_NLS_ISO8859_3=m
+CONFIG_NLS_ISO8859_4=m
+CONFIG_NLS_ISO8859_5=m
+CONFIG_NLS_ISO8859_6=m
+CONFIG_NLS_ISO8859_7=m
+CONFIG_NLS_ISO8859_9=m
+CONFIG_NLS_ISO8859_13=m
+CONFIG_NLS_ISO8859_14=m
+CONFIG_NLS_ISO8859_15=m
+CONFIG_NLS_KOI8_R=m
+CONFIG_NLS_KOI8_U=m
+CONFIG_NLS_UTF8=m
+# CONFIG_DLM is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+# CONFIG_ENABLE_WARN_DEPRECATED is not set
+# CONFIG_ENABLE_MUST_CHECK is not set
+CONFIG_FRAME_WARN=1024
+# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_UNUSED_SYMBOLS is not set
+CONFIG_DEBUG_FS=y
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
+CONFIG_DETECT_HUNG_TASK=y
+# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
+CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_OBJECTS is not set
+# CONFIG_SLUB_DEBUG_ON is not set
+# CONFIG_SLUB_STATS is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+CONFIG_DEBUG_BUGVERBOSE=y
+CONFIG_DEBUG_INFO=y
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_WRITECOUNT is not set
+CONFIG_DEBUG_MEMORY_INIT=y
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_RCU_CPU_STALL_DETECTOR is not set
+# CONFIG_BACKTRACE_SELF_TEST is not set
+# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_LATENCYTOP is not set
+CONFIG_SYSCTL_SYSCALL_CHECK=y
+# CONFIG_PAGE_POISONING is not set
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_TRACING_SUPPORT=y
+
+#
+# Tracers
+#
+# CONFIG_FUNCTION_TRACER is not set
+# CONFIG_SCHED_TRACER is not set
+# CONFIG_CONTEXT_SWITCH_TRACER is not set
+# CONFIG_EVENT_TRACER is not set
+# CONFIG_BOOT_TRACER is not set
+# CONFIG_TRACE_BRANCH_PROFILING is not set
+# CONFIG_STACK_TRACER is not set
+# CONFIG_KMEMTRACE is not set
+# CONFIG_WORKQUEUE_TRACER is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_DYNAMIC_DEBUG is not set
+# CONFIG_SAMPLES is not set
+CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_KGDB is not set
+CONFIG_ARM_UNWIND=y
+CONFIG_DEBUG_USER=y
+# CONFIG_DEBUG_ERRORS is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_LL is not set
+CONFIG_DEBUG_S3C_UART=0
+
+#
+# Security options
+#
+CONFIG_KEYS=y
+# CONFIG_KEYS_DEBUG_PROC_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITYFS is not set
+CONFIG_SECURITY_FILE_CAPABILITIES=y
+CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
+CONFIG_CRYPTO_FIPS=y
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_ALGAPI2=y
+CONFIG_CRYPTO_AEAD=m
+CONFIG_CRYPTO_AEAD2=y
+CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_BLKCIPHER2=y
+CONFIG_CRYPTO_HASH=y
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_RNG=m
+CONFIG_CRYPTO_RNG2=y
+CONFIG_CRYPTO_PCOMP=y
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_MANAGER2=y
+CONFIG_CRYPTO_GF128MUL=m
+CONFIG_CRYPTO_NULL=m
+CONFIG_CRYPTO_WORKQUEUE=y
+CONFIG_CRYPTO_CRYPTD=m
+CONFIG_CRYPTO_AUTHENC=m
+CONFIG_CRYPTO_TEST=m
+
+#
+# Authenticated Encryption with Associated Data
+#
+CONFIG_CRYPTO_CCM=m
+CONFIG_CRYPTO_GCM=m
+CONFIG_CRYPTO_SEQIV=m
+
+#
+# Block modes
+#
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_CTR=m
+CONFIG_CRYPTO_CTS=m
+CONFIG_CRYPTO_ECB=y
+CONFIG_CRYPTO_LRW=m
+CONFIG_CRYPTO_PCBC=m
+CONFIG_CRYPTO_XTS=m
+
+#
+# Hash modes
+#
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_XCBC=m
+
+#
+# Digest
+#
+CONFIG_CRYPTO_CRC32C=m
+CONFIG_CRYPTO_MD4=m
+CONFIG_CRYPTO_MD5=y
+CONFIG_CRYPTO_MICHAEL_MIC=y
+CONFIG_CRYPTO_RMD128=m
+CONFIG_CRYPTO_RMD160=m
+CONFIG_CRYPTO_RMD256=m
+CONFIG_CRYPTO_RMD320=m
+CONFIG_CRYPTO_SHA1=m
+CONFIG_CRYPTO_SHA256=m
+CONFIG_CRYPTO_SHA512=m
+CONFIG_CRYPTO_TGR192=m
+CONFIG_CRYPTO_WP512=m
+
+#
+# Ciphers
+#
+CONFIG_CRYPTO_AES=y
+CONFIG_CRYPTO_ANUBIS=m
+CONFIG_CRYPTO_ARC4=y
+CONFIG_CRYPTO_BLOWFISH=m
+CONFIG_CRYPTO_CAMELLIA=m
+CONFIG_CRYPTO_CAST5=m
+CONFIG_CRYPTO_CAST6=m
+CONFIG_CRYPTO_DES=y
+CONFIG_CRYPTO_FCRYPT=m
+CONFIG_CRYPTO_KHAZAD=m
+CONFIG_CRYPTO_SALSA20=m
+CONFIG_CRYPTO_SEED=m
+CONFIG_CRYPTO_SERPENT=m
+CONFIG_CRYPTO_TEA=m
+CONFIG_CRYPTO_TWOFISH=m
+CONFIG_CRYPTO_TWOFISH_COMMON=m
+
+#
+# Compression
+#
+CONFIG_CRYPTO_DEFLATE=m
+CONFIG_CRYPTO_ZLIB=m
+CONFIG_CRYPTO_LZO=m
+
+#
+# Random Number Generation
+#
+CONFIG_CRYPTO_ANSI_CPRNG=m
+CONFIG_CRYPTO_HW=y
+# CONFIG_BINARY_PRINTF is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+CONFIG_GENERIC_FIND_LAST_BIT=y
+CONFIG_CRC_CCITT=m
+CONFIG_CRC16=m
+CONFIG_CRC_T10DIF=y
+CONFIG_CRC_ITU_T=y
+CONFIG_CRC32=y
+CONFIG_CRC7=y
+CONFIG_LIBCRC32C=m
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_LZO_COMPRESS=m
+CONFIG_LZO_DECOMPRESS=m
+CONFIG_DECOMPRESS_GZIP=y
+CONFIG_DECOMPRESS_BZIP2=y
+CONFIG_DECOMPRESS_LZMA=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_DMA=y
+CONFIG_NLATTR=y
#define __NR_inotify_init1 (__NR_SYSCALL_BASE+360)
#define __NR_preadv (__NR_SYSCALL_BASE+361)
#define __NR_pwritev (__NR_SYSCALL_BASE+362)
+#define __NR_rt_tgsigqueueinfo (__NR_SYSCALL_BASE+363)
+#define __NR_perf_counter_open (__NR_SYSCALL_BASE+364)
/*
* The following SWIs are ARM private.
/* 360 */ CALL(sys_inotify_init1)
CALL(sys_preadv)
CALL(sys_pwritev)
+ CALL(sys_rt_tgsigqueueinfo)
+ CALL(sys_perf_counter_open)
#ifndef syscalls_counted
.equ syscalls_padding, ((NR_syscalls + 3) & ~3) - NR_syscalls
#define syscalls_counted
#ifdef CONFIG_SMP
cpumask_setall(bad_irq_desc.affinity);
- bad_irq_desc.cpu = smp_processor_id();
+ bad_irq_desc.node = smp_processor_id();
#endif
init_arch_irq();
}
static void route_irq(struct irq_desc *desc, unsigned int irq, unsigned int cpu)
{
- pr_debug("IRQ%u: moving from cpu%u to cpu%u\n", irq, desc->cpu, cpu);
+ pr_debug("IRQ%u: moving from cpu%u to cpu%u\n", irq, desc->node, cpu);
spin_lock_irq(&desc->lock);
desc->chip->set_affinity(irq, cpumask_of(cpu));
for (i = 0; i < NR_IRQS; i++) {
struct irq_desc *desc = irq_desc + i;
- if (desc->cpu == cpu) {
+ if (desc->node == cpu) {
unsigned int newcpu = cpumask_any_and(desc->affinity,
cpu_online_mask);
if (newcpu >= nr_cpu_ids) {
/*
* Function pointers to optional machine specific functions
*/
-void (*pm_idle)(void);
-EXPORT_SYMBOL(pm_idle);
-
void (*pm_power_off)(void);
EXPORT_SYMBOL(pm_power_off);
*/
static void default_idle(void)
{
- if (hlt_counter)
- cpu_relax();
- else {
- local_irq_disable();
- if (!need_resched())
- arch_idle();
- local_irq_enable();
- }
+ if (!need_resched())
+ arch_idle();
+ local_irq_enable();
}
+void (*pm_idle)(void) = default_idle;
+EXPORT_SYMBOL(pm_idle);
+
/*
- * The idle thread. We try to conserve power, while trying to keep
- * overall latency low. The architecture specific idle is passed
- * a value to indicate the level of "idleness" of the system.
+ * The idle thread, has rather strange semantics for calling pm_idle,
+ * but this is what x86 does and we need to do the same, so that
+ * things like cpuidle get called in the same way. The only difference
+ * is that we always respect 'hlt_counter' to prevent low power idle.
*/
void cpu_idle(void)
{
/* endless idle loop with no priority at all */
while (1) {
- void (*idle)(void) = pm_idle;
-
+ tick_nohz_stop_sched_tick(1);
+ leds_event(led_idle_start);
+ while (!need_resched()) {
#ifdef CONFIG_HOTPLUG_CPU
- if (cpu_is_offline(smp_processor_id())) {
- leds_event(led_idle_start);
- cpu_die();
- }
+ if (cpu_is_offline(smp_processor_id()))
+ cpu_die();
#endif
- if (!idle)
- idle = default_idle;
- leds_event(led_idle_start);
- tick_nohz_stop_sched_tick(1);
- while (!need_resched())
- idle();
+ local_irq_disable();
+ if (hlt_counter) {
+ local_irq_enable();
+ cpu_relax();
+ } else {
+ stop_critical_timings();
+ pm_idle();
+ start_critical_timings();
+ /*
+ * This will eventually be removed - pm_idle
+ * functions should always return with IRQs
+ * enabled.
+ */
+ WARN_ON(irqs_disabled());
+ local_irq_enable();
+ }
+ }
leds_event(led_idle_end);
tick_nohz_restart_sched_tick();
preempt_enable_no_resched();
" .size kernel_thread_helper, . - kernel_thread_helper\n"
" .previous");
+#ifdef CONFIG_ARM_UNWIND
+extern void kernel_thread_exit(long code);
+asm( ".section .text\n"
+" .align\n"
+" .type kernel_thread_exit, #function\n"
+"kernel_thread_exit:\n"
+" .fnstart\n"
+" .cantunwind\n"
+" bl do_exit\n"
+" nop\n"
+" .fnend\n"
+" .size kernel_thread_exit, . - kernel_thread_exit\n"
+" .previous");
+#else
+#define kernel_thread_exit do_exit
+#endif
+
/*
* Create a kernel thread.
*/
regs.ARM_r1 = (unsigned long)arg;
regs.ARM_r2 = (unsigned long)fn;
- regs.ARM_r3 = (unsigned long)do_exit;
+ regs.ARM_r3 = (unsigned long)kernel_thread_exit;
regs.ARM_pc = (unsigned long)kernel_thread_helper;
regs.ARM_cpsr = SVC_MODE | PSR_ENDSTATE;
ctrl->vrs[14] = *vsp++;
ctrl->vrs[SP] = (unsigned long)vsp;
} else if (insn == 0xb0) {
- ctrl->vrs[PC] = ctrl->vrs[LR];
+ if (ctrl->vrs[PC] == 0)
+ ctrl->vrs[PC] = ctrl->vrs[LR];
/* no further processing */
ctrl->entries = 0;
} else if (insn == 0xb1) {
}
while (ctrl.entries > 0) {
- int urc;
-
- if (ctrl.vrs[SP] < low || ctrl.vrs[SP] >= high)
- return -URC_FAILURE;
- urc = unwind_exec_insn(&ctrl);
+ int urc = unwind_exec_insn(&ctrl);
if (urc < 0)
return urc;
+ if (ctrl.vrs[SP] < low || ctrl.vrs[SP] >= high)
+ return -URC_FAILURE;
}
if (ctrl.vrs[PC] == 0)
ctrl.vrs[PC] = ctrl.vrs[LR];
+ /* check for infinite loop */
+ if (frame->pc == ctrl.vrs[PC])
+ return -URC_FAILURE;
+
frame->fp = ctrl.vrs[FP];
frame->sp = ctrl.vrs[SP];
frame->lr = ctrl.vrs[LR];
void unwind_backtrace(struct pt_regs *regs, struct task_struct *tsk)
{
struct stackframe frame;
- unsigned long high, low;
register unsigned long current_sp asm ("sp");
pr_debug("%s(regs = %p tsk = %p)\n", __func__, regs, tsk);
frame.pc = thread_saved_pc(tsk);
}
- low = frame.sp & ~(THREAD_SIZE - 1);
- high = low + THREAD_SIZE;
-
while (1) {
int urc;
unsigned long where = frame.pc;
*(.exitcall.exit)
*(.ARM.exidx.exit.text)
*(.ARM.extab.exit.text)
+#ifndef CONFIG_HOTPLUG_CPU
+ *(.ARM.exidx.cpuexit.text)
+ *(.ARM.extab.cpuexit.text)
+#endif
+#ifndef CONFIG_HOTPLUG
+ *(.ARM.exidx.devexit.text)
+ *(.ARM.extab.devexit.text)
+#endif
#ifndef CONFIG_MMU
*(.fixup)
*(__ex_table)
udelay(1);
}
- if (i < MAX_CLOCK_ENABLE_WAIT)
+ if (i <= MAX_CLOCK_ENABLE_WAIT)
pr_debug("Clock %s stable after %d loops\n", name, i);
else
printk(KERN_ERR "Clock %s didn't enable in %d tries\n",
#define MIN_SDRC_DLL_LOCK_FREQ 83000000
+#define CYCLES_PER_MHZ 1000000
+
+/* Scale factor for fixed-point arith in omap3_core_dpll_m2_set_rate() */
+#define SDRC_MPURATE_SCALE 8
+
+/* 2^SDRC_MPURATE_BASE_SHIFT: MPU MHz that SDRC_MPURATE_LOOPS is defined for */
+#define SDRC_MPURATE_BASE_SHIFT 9
+
+/*
+ * SDRC_MPURATE_LOOPS: Number of MPU loops to execute at
+ * 2^MPURATE_BASE_SHIFT MHz for SDRC to stabilize
+ */
+#define SDRC_MPURATE_LOOPS 96
+
/**
* omap3_dpll_recalc - recalculate DPLL rate
* @clk: DPLL struct clk
{
u32 new_div = 0;
u32 unlock_dll = 0;
- unsigned long validrate, sdrcrate;
+ u32 c;
+ unsigned long validrate, sdrcrate, mpurate;
struct omap_sdrc_params *sp;
if (!clk || !rate)
if (clk != &dpll3_m2_ck)
return -EINVAL;
- if (rate == clk->rate)
- return 0;
-
validrate = omap2_clksel_round_rate_div(clk, rate, &new_div);
if (validrate != rate)
return -EINVAL;
sdrcrate = sdrc_ick.rate;
if (rate > clk->rate)
- sdrcrate <<= ((rate / clk->rate) - 1);
+ sdrcrate <<= ((rate / clk->rate) >> 1);
else
- sdrcrate >>= ((clk->rate / rate) - 1);
+ sdrcrate >>= ((clk->rate / rate) >> 1);
sp = omap2_sdrc_get_params(sdrcrate);
if (!sp)
unlock_dll = 1;
}
+ /*
+ * XXX This only needs to be done when the CPU frequency changes
+ */
+ mpurate = arm_fck.rate / CYCLES_PER_MHZ;
+ c = (mpurate << SDRC_MPURATE_SCALE) >> SDRC_MPURATE_BASE_SHIFT;
+ c += 1; /* for safety */
+ c *= SDRC_MPURATE_LOOPS;
+ c >>= SDRC_MPURATE_SCALE;
+ if (c == 0)
+ c = 1;
+
pr_debug("clock: changing CORE DPLL rate from %lu to %lu\n", clk->rate,
validrate);
pr_debug("clock: SDRC timing params used: %08x %08x %08x\n",
sp->rfr_ctrl, sp->actim_ctrla, sp->actim_ctrlb);
- /* REVISIT: SRAM code doesn't support other M2 divisors yet */
- WARN_ON(new_div != 1 && new_div != 2);
-
- /* REVISIT: Add SDRC_MR changing to this code also */
omap3_configure_core_dpll(sp->rfr_ctrl, sp->actim_ctrla,
- sp->actim_ctrlb, new_div, unlock_dll);
+ sp->actim_ctrlb, new_div, unlock_dll, c,
+ sp->mr, rate > clk->rate);
return 0;
}
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/io.h>
+#include <linux/clk.h>
#include <asm/tlb.h>
omapfb_reserve_sdram();
}
+/*
+ * omap2_init_reprogram_sdrc - reprogram SDRC timing parameters
+ *
+ * Sets the CORE DPLL3 M2 divider to the same value that it's at
+ * currently. This has the effect of setting the SDRC SDRAM AC timing
+ * registers to the values currently defined by the kernel. Currently
+ * only defined for OMAP3; will return 0 if called on OMAP2. Returns
+ * -EINVAL if the dpll3_m2_ck cannot be found, 0 if called on OMAP2,
+ * or passes along the return value of clk_set_rate().
+ */
+static int __init _omap2_init_reprogram_sdrc(void)
+{
+ struct clk *dpll3_m2_ck;
+ int v = -EINVAL;
+ long rate;
+
+ if (!cpu_is_omap34xx())
+ return 0;
+
+ dpll3_m2_ck = clk_get(NULL, "dpll3_m2_ck");
+ if (!dpll3_m2_ck)
+ return -EINVAL;
+
+ rate = clk_get_rate(dpll3_m2_ck);
+ pr_info("Reprogramming SDRC clock to %ld Hz\n", rate);
+ v = clk_set_rate(dpll3_m2_ck, rate);
+ if (v)
+ pr_err("dpll3_m2_clk rate change failed: %d\n", v);
+
+ clk_put(dpll3_m2_ck);
+
+ return v;
+}
+
void __init omap2_init_common_hw(struct omap_sdrc_params *sp)
{
omap2_mux_init();
clkdm_init(clockdomains_omap, clkdm_pwrdm_autodeps);
omap2_clk_init();
omap2_sdrc_init(sp);
+ _omap2_init_reprogram_sdrc();
#endif
gpmc_init();
}
(c++ < PWRDM_TRANSITION_BAILOUT))
udelay(1);
- if (c >= PWRDM_TRANSITION_BAILOUT) {
+ if (c > PWRDM_TRANSITION_BAILOUT) {
printk(KERN_ERR "powerdomain: waited too long for "
"powerdomain %s to complete transition\n", pwrdm->name);
return -EAGAIN;
*
* Omap3 specific functions that need to be run in internal SRAM
*
- * (C) Copyright 2007
- * Texas Instruments Inc.
- * Rajendra Nayak <rnayak@ti.com>
+ * Copyright (C) 2004, 2007, 2008 Texas Instruments, Inc.
+ * Copyright (C) 2008 Nokia Corporation
*
- * (C) Copyright 2004
- * Texas Instruments, <www.ti.com>
+ * Rajendra Nayak <rnayak@ti.com>
* Richard Woodruff <r-woodruff2@ti.com>
+ * Paul Walmsley
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
.text
+/* r4 parameters */
+#define SDRC_NO_UNLOCK_DLL 0x0
+#define SDRC_UNLOCK_DLL 0x1
+
+/* SDRC_DLLA_CTRL bit settings */
+#define FIXEDDELAY_SHIFT 24
+#define FIXEDDELAY_MASK (0xff << FIXEDDELAY_SHIFT)
+#define DLLIDLE_MASK 0x4
+
+/*
+ * SDRC_DLLA_CTRL default values: TI hardware team indicates that
+ * FIXEDDELAY should be initialized to 0xf. This apparently was
+ * empirically determined during process testing, so no derivation
+ * was provided.
+ */
+#define FIXEDDELAY_DEFAULT (0x0f << FIXEDDELAY_SHIFT)
+
+/* SDRC_DLLA_STATUS bit settings */
+#define LOCKSTATUS_MASK 0x4
+
+/* SDRC_POWER bit settings */
+#define SRFRONIDLEREQ_MASK 0x40
+#define PWDENA_MASK 0x4
+
+/* CM_IDLEST1_CORE bit settings */
+#define ST_SDRC_MASK 0x2
+
+/* CM_ICLKEN1_CORE bit settings */
+#define EN_SDRC_MASK 0x2
+
+/* CM_CLKSEL1_PLL bit settings */
+#define CORE_DPLL_CLKOUT_DIV_SHIFT 0x1b
+
/*
- * Change frequency of core dpll
- * r0 = sdrc_rfr_ctrl r1 = sdrc_actim_ctrla r2 = sdrc_actim_ctrlb r3 = M2
- * r4 = Unlock SDRC DLL? (1 = yes, 0 = no) -- only unlock DLL for
+ * omap3_sram_configure_core_dpll - change DPLL3 M2 divider
+ * r0 = new SDRC_RFR_CTRL register contents
+ * r1 = new SDRC_ACTIM_CTRLA register contents
+ * r2 = new SDRC_ACTIM_CTRLB register contents
+ * r3 = new M2 divider setting (only 1 and 2 supported right now)
+ * r4 = unlock SDRC DLL? (1 = yes, 0 = no). Only unlock DLL for
* SDRC rates < 83MHz
+ * r5 = number of MPU cycles to wait for SDRC to stabilize after
+ * reprogramming the SDRC when switching to a slower MPU speed
+ * r6 = new SDRC_MR_0 register value
+ * r7 = increasing SDRC rate? (1 = yes, 0 = no)
+ *
*/
ENTRY(omap3_sram_configure_core_dpll)
stmfd sp!, {r1-r12, lr} @ store regs to stack
ldr r4, [sp, #52] @ pull extra args off the stack
+ ldr r5, [sp, #56] @ load extra args from the stack
+ ldr r6, [sp, #60] @ load extra args from the stack
+ ldr r7, [sp, #64] @ load extra args from the stack
dsb @ flush buffered writes to interconnect
- cmp r3, #0x2
- blne configure_sdrc
- cmp r4, #0x1
+ cmp r7, #1 @ if increasing SDRC clk rate,
+ bleq configure_sdrc @ program the SDRC regs early (for RFR)
+ cmp r4, #SDRC_UNLOCK_DLL @ set the intended DLL state
bleq unlock_dll
blne lock_dll
- bl sdram_in_selfrefresh @ put the SDRAM in self refresh
- bl configure_core_dpll
- bl enable_sdrc
- cmp r4, #0x1
+ bl sdram_in_selfrefresh @ put SDRAM in self refresh, idle SDRC
+ bl configure_core_dpll @ change the DPLL3 M2 divider
+ bl enable_sdrc @ take SDRC out of idle
+ cmp r4, #SDRC_UNLOCK_DLL @ wait for DLL status to change
bleq wait_dll_unlock
blne wait_dll_lock
- cmp r3, #0x1
- blne configure_sdrc
+ cmp r7, #1 @ if increasing SDRC clk rate,
+ beq return_to_sdram @ return to SDRAM code, otherwise,
+ bl configure_sdrc @ reprogram SDRC regs now
+ mov r12, r5
+ bl wait_clk_stable @ wait for SDRC to stabilize
+return_to_sdram:
isb @ prevent speculative exec past here
mov r0, #0 @ return value
ldmfd sp!, {r1-r12, pc} @ restore regs and return
unlock_dll:
ldr r11, omap3_sdrc_dlla_ctrl
ldr r12, [r11]
- orr r12, r12, #0x4
+ and r12, r12, #FIXEDDELAY_MASK
+ orr r12, r12, #FIXEDDELAY_DEFAULT
+ orr r12, r12, #DLLIDLE_MASK
str r12, [r11] @ (no OCP barrier needed)
bx lr
lock_dll:
ldr r11, omap3_sdrc_dlla_ctrl
ldr r12, [r11]
- bic r12, r12, #0x4
+ bic r12, r12, #DLLIDLE_MASK
str r12, [r11] @ (no OCP barrier needed)
bx lr
sdram_in_selfrefresh:
ldr r11, omap3_sdrc_power @ read the SDRC_POWER register
ldr r12, [r11] @ read the contents of SDRC_POWER
mov r9, r12 @ keep a copy of SDRC_POWER bits
- orr r12, r12, #0x40 @ enable self refresh on idle req
- bic r12, r12, #0x4 @ clear PWDENA
+ orr r12, r12, #SRFRONIDLEREQ_MASK @ enable self refresh on idle
+ bic r12, r12, #PWDENA_MASK @ clear PWDENA
str r12, [r11] @ write back to SDRC_POWER register
ldr r12, [r11] @ posted-write barrier for SDRC
+idle_sdrc:
ldr r11, omap3_cm_iclken1_core @ read the CM_ICLKEN1_CORE reg
ldr r12, [r11]
- bic r12, r12, #0x2 @ disable iclk bit for SDRC
+ bic r12, r12, #EN_SDRC_MASK @ disable iclk bit for SDRC
str r12, [r11]
wait_sdrc_idle:
ldr r11, omap3_cm_idlest1_core
ldr r12, [r11]
- and r12, r12, #0x2 @ check for SDRC idle
- cmp r12, #2
+ and r12, r12, #ST_SDRC_MASK @ check for SDRC idle
+ cmp r12, #ST_SDRC_MASK
bne wait_sdrc_idle
bx lr
configure_core_dpll:
ldr r12, [r11]
ldr r10, core_m2_mask_val @ modify m2 for core dpll
and r12, r12, r10
- orr r12, r12, r3, lsl #0x1B @ r3 contains the M2 val
+ orr r12, r12, r3, lsl #CORE_DPLL_CLKOUT_DIV_SHIFT
str r12, [r11]
ldr r12, [r11] @ posted-write barrier for CM
- mov r12, #0x800 @ wait for the clock to stabilise
- cmp r3, #2
- bne wait_clk_stable
bx lr
wait_clk_stable:
subs r12, r12, #1
bne wait_clk_stable
- nop
- nop
- nop
- nop
- nop
- nop
- nop
- nop
- nop
- nop
bx lr
enable_sdrc:
ldr r11, omap3_cm_iclken1_core
ldr r12, [r11]
- orr r12, r12, #0x2 @ enable iclk bit for SDRC
+ orr r12, r12, #EN_SDRC_MASK @ enable iclk bit for SDRC
str r12, [r11]
wait_sdrc_idle1:
ldr r11, omap3_cm_idlest1_core
ldr r12, [r11]
- and r12, r12, #0x2
+ and r12, r12, #ST_SDRC_MASK
cmp r12, #0
bne wait_sdrc_idle1
restore_sdrc_power_val:
wait_dll_lock:
ldr r11, omap3_sdrc_dlla_status
ldr r12, [r11]
- and r12, r12, #0x4
- cmp r12, #0x4
+ and r12, r12, #LOCKSTATUS_MASK
+ cmp r12, #LOCKSTATUS_MASK
bne wait_dll_lock
bx lr
wait_dll_unlock:
ldr r11, omap3_sdrc_dlla_status
ldr r12, [r11]
- and r12, r12, #0x4
+ and r12, r12, #LOCKSTATUS_MASK
cmp r12, #0x0
bne wait_dll_unlock
bx lr
str r1, [r11]
ldr r11, omap3_sdrc_actim_ctrlb
str r2, [r11]
- ldr r2, [r11] @ posted-write barrier for SDRC
+ ldr r11, omap3_sdrc_mr_0
+ str r6, [r11]
+ ldr r6, [r11] @ posted-write barrier for SDRC
bx lr
omap3_sdrc_power:
.word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_A_0)
omap3_sdrc_actim_ctrlb:
.word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_B_0)
+omap3_sdrc_mr_0:
+ .word OMAP34XX_SDRC_REGADDR(SDRC_MR_0)
omap3_sdrc_dlla_status:
.word OMAP34XX_SDRC_REGADDR(SDRC_DLLA_STATUS)
omap3_sdrc_dlla_ctrl:
int __init orion5x_setup_sram_win(void)
{
- return setup_cpu_win(win_alloc_count, ORION5X_SRAM_PHYS_BASE,
+ return setup_cpu_win(win_alloc_count++, ORION5X_SRAM_PHYS_BASE,
ORION5X_SRAM_SIZE, TARGET_SRAM, ATTR_SRAM, -1);
}
.resource = orion5x_crypto_res,
};
-int __init orion5x_crypto_init(void)
+static int __init orion5x_crypto_init(void)
{
int ret;
disable_hlt();
}
+ /*
+ * The 5082/5181l/5182/6082/6082l/6183 have crypto
+ * while 5180n/5181/5281 don't have crypto.
+ */
+ if ((dev == MV88F5181_DEV_ID && rev >= MV88F5181L_REV_A0) ||
+ dev == MV88F5182_DEV_ID || dev == MV88F6183_DEV_ID)
+ orion5x_crypto_init();
+
/*
* Register watchdog driver
*/
void orion5x_uart0_init(void);
void orion5x_uart1_init(void);
void orion5x_xor_init(void);
-int orion5x_crypto_init(void);
/*
* PCIe/PCI functions.
Say Y here if you intend to run this kernel on Palm Zire 72
handheld computer.
+config MACH_TREO680
+ bool "Palm Treo 680"
+ default y
+ depends on ARCH_PXA_PALM
+ select PXA27x
+ select IWMMXT
+ help
+ Say Y here if you intend to run this kernel on Palm Treo 680
+ smartphone.
+
config MACH_PALMLD
bool "Palm LifeDrive"
default y
obj-$(CONFIG_MACH_PALMTX) += palmtx.o
obj-$(CONFIG_MACH_PALMLD) += palmld.o
obj-$(CONFIG_MACH_PALMZ72) += palmz72.o
+obj-$(CONFIG_MACH_TREO680) += treo680.o
obj-$(CONFIG_ARCH_VIPER) += viper.o
ifeq ($(CONFIG_MACH_ZYLONITE),y)
#include <linux/pm.h>
#include <linux/gpio.h>
#include <linux/backlight.h>
+#include <linux/i2c.h>
#include <linux/io.h>
#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
&sharpsl_rom_device,
};
+static struct i2c_board_info __initdata corgi_i2c_devices[] = {
+ { I2C_BOARD_INFO("wm8731", 0x1b) },
+};
+
static void corgi_poweroff(void)
{
if (!machine_is_corgi())
pxa_set_mci_info(&corgi_mci_platform_data);
pxa_set_ficp_info(&corgi_ficp_platform_data);
pxa_set_i2c_info(NULL);
+ i2c_register_board_info(0, ARRAY_AND_SIZE(corgi_i2c_devices));
platform_scoop_config = &corgi_pcmcia_config;
#include <linux/apm-emulation.h>
#include <linux/i2c.h>
#include <linux/i2c/pca953x.h>
+#include <linux/regulator/userspace-consumer.h>
#include <media/soc_camera.h>
.rx_threshold = 1,
.tx_threshold = 1,
.timeout = 1000,
+ .gpio_cs = 14,
};
static unsigned long em_x270_libertas_pin_config[] = {
struct libertas_spi_platform_data em_x270_libertas_pdata = {
.use_dummy_writes = 1,
- .gpio_cs = 14,
.setup = em_x270_libertas_setup,
.teardown = em_x270_libertas_teardown,
};
static inline void em_x270_init_spi(void) {}
#endif
-#if defined(CONFIG_SND_PXA2XX_AC97) || defined(CONFIG_SND_PXA2XX_AC97_MODULE)
+#if defined(CONFIG_SND_PXA2XX_LIB_AC97)
+static pxa2xx_audio_ops_t em_x270_ac97_info = {
+ .reset_gpio = 113,
+};
+
static void __init em_x270_init_ac97(void)
{
- pxa_set_ac97_info(NULL);
+ pxa_set_ac97_info(&em_x270_ac97_info);
}
#else
static inline void em_x270_init_ac97(void) {}
static inline void em_x270_init_camera(void) {}
#endif
+static struct regulator_bulk_data em_x270_gps_consumer_supply = {
+ .supply = "vcc gps",
+};
+
+static struct regulator_userspace_consumer_data em_x270_gps_consumer_data = {
+ .name = "vcc gps",
+ .num_supplies = 1,
+ .supplies = &em_x270_gps_consumer_supply,
+};
+
+static struct platform_device em_x270_gps_userspace_consumer = {
+ .name = "reg-userspace-consumer",
+ .id = 0,
+ .dev = {
+ .platform_data = &em_x270_gps_consumer_data,
+ },
+};
+
+static struct regulator_bulk_data em_x270_gprs_consumer_supply = {
+ .supply = "vcc gprs",
+};
+
+static struct regulator_userspace_consumer_data em_x270_gprs_consumer_data = {
+ .name = "vcc gprs",
+ .num_supplies = 1,
+ .supplies = &em_x270_gprs_consumer_supply
+};
+
+static struct platform_device em_x270_gprs_userspace_consumer = {
+ .name = "reg-userspace-consumer",
+ .id = 1,
+ .dev = {
+ .platform_data = &em_x270_gprs_consumer_data,
+ }
+};
+
+static struct platform_device *em_x270_userspace_consumers[] = {
+ &em_x270_gps_userspace_consumer,
+ &em_x270_gprs_userspace_consumer,
+};
+
+static void __init em_x270_userspace_consumers_init(void)
+{
+ platform_add_devices(ARRAY_AND_SIZE(em_x270_userspace_consumers));
+}
+
/* DA9030 related initializations */
#define REGULATOR_CONSUMER(_name, _dev, _supply) \
static struct regulator_consumer_supply _name##_consumers[] = { \
}, \
}
-REGULATOR_CONSUMER(ldo3, NULL, "vcc gps");
+REGULATOR_CONSUMER(ldo3, &em_x270_gps_userspace_consumer.dev, "vcc gps");
REGULATOR_CONSUMER(ldo5, NULL, "vcc cam");
REGULATOR_CONSUMER(ldo10, &pxa_device_mci.dev, "vcc sdio");
REGULATOR_CONSUMER(ldo12, NULL, "vcc usb");
-REGULATOR_CONSUMER(ldo19, NULL, "vcc gprs");
+REGULATOR_CONSUMER(ldo19, &em_x270_gprs_userspace_consumer.dev, "vcc gprs");
#define REGULATOR_INIT(_ldo, _min_uV, _max_uV, _ops_mask) \
static struct regulator_init_data _ldo##_data = { \
.enabled = 0, \
}, \
.valid_ops_mask = _ops_mask, \
+ .apply_uV = 1, \
}, \
.num_consumer_supplies = ARRAY_SIZE(_ldo##_consumers), \
.consumer_supplies = _ldo##_consumers, \
em_x270_init_spi();
em_x270_init_i2c();
em_x270_init_camera();
+ em_x270_userspace_consumers_init();
}
MACHINE_START(EM_X270, "Compulab EM-X270")
#include <linux/pwm_backlight.h>
#include <linux/regulator/bq24022.h>
#include <linux/regulator/machine.h>
+#include <linux/regulator/max1586.h>
#include <linux/spi/ads7846.h>
#include <linux/spi/spi.h>
#include <linux/usb/gpio_vbus.h>
},
};
+/*
+ * Maxim MAX1587A on PI2C
+ */
+
+static struct regulator_consumer_supply max1587a_consumer = {
+ .supply = "vcc_core",
+};
+
+static struct regulator_init_data max1587a_v3_info = {
+ .constraints = {
+ .name = "vcc_core range",
+ .min_uV = 900000,
+ .max_uV = 1705000,
+ .always_on = 1,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &max1587a_consumer,
+};
+
+static struct max1586_subdev_data max1587a_subdev = {
+ .name = "vcc_core",
+ .id = MAX1586_V3,
+ .platform_data = &max1587a_v3_info,
+};
+
+static struct max1586_platform_data max1587a_info = {
+ .num_subdevs = 1,
+ .subdevs = &max1587a_subdev,
+ .v3_gain = MAX1586_GAIN_R24_3k32, /* 730..1550 mV */
+};
+
+static struct i2c_board_info __initdata pi2c_board_info[] = {
+ {
+ I2C_BOARD_INFO("max1586", 0x14),
+ .platform_data = &max1587a_info,
+ },
+};
+
/*
* PCMCIA
*/
pxa_set_ficp_info(&ficp_info);
pxa27x_set_i2c_power_info(NULL);
pxa_set_i2c_info(NULL);
+ i2c_register_board_info(1, ARRAY_AND_SIZE(pi2c_board_info));
pxa2xx_set_spi_info(2, &pxa_ssp2_master_info);
spi_register_board_info(ARRAY_AND_SIZE(tsc2046_board_info));
/* SD/MMC */
#define GPIO_NR_PALMZ72_SD_DETECT_N 14
#define GPIO_NR_PALMZ72_SD_POWER_N 98
-#define GPIO_NR_PALMZ72_SD_RO 115
+#define GPIO_NR_PALMZ72_SD_RO 115
/* Touchscreen */
#define GPIO_NR_PALMZ72_WM9712_IRQ 27
/* USB */
#define GPIO_NR_PALMZ72_USB_DETECT_N 15
-#define GPIO_NR_PALMZ72_USB_POWER 95
-#define GPIO_NR_PALMZ72_USB_PULLUP 12
+#define GPIO_NR_PALMZ72_USB_PULLUP 95
/* LCD/Backlight */
#define GPIO_NR_PALMZ72_BL_POWER 20
--- /dev/null
+/*
+ * GPIOs and interrupts for Palm Treo 680 smartphone
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#ifndef _INCLUDE_TREO680_H_
+#define _INCLUDE_TREO680_H_
+
+/* GPIOs */
+#define GPIO_NR_TREO680_POWER_DETECT 0
+#define GPIO_NR_TREO680_AMP_EN 27
+#define GPIO_NR_TREO680_KEYB_BL 24
+#define GPIO_NR_TREO680_VIBRATE_EN 44
+#define GPIO_NR_TREO680_GREEN_LED 20
+#define GPIO_NR_TREO680_RED_LED 79
+#define GPIO_NR_TREO680_SD_DETECT_N 113
+#define GPIO_NR_TREO680_SD_READONLY 33
+#define GPIO_NR_TREO680_EP_DETECT_N 116
+#define GPIO_NR_TREO680_SD_POWER 42
+#define GPIO_NR_TREO680_USB_DETECT 1
+#define GPIO_NR_TREO680_USB_PULLUP 114
+#define GPIO_NR_TREO680_GSM_POWER 40
+#define GPIO_NR_TREO680_GSM_RESET 87
+#define GPIO_NR_TREO680_GSM_WAKE 57
+#define GPIO_NR_TREO680_GSM_HOST_WAKE 14
+#define GPIO_NR_TREO680_GSM_TRIGGER 10
+#define GPIO_NR_TREO680_BT_EN 43
+#define GPIO_NR_TREO680_IR_EN 115
+#define GPIO_NR_TREO680_IR_TXD 47
+#define GPIO_NR_TREO680_BL_POWER 38
+#define GPIO_NR_TREO680_LCD_POWER 25
+
+/* Various addresses */
+#define TREO680_PHYS_RAM_START 0xa0000000
+#define TREO680_PHYS_IO_START 0x40000000
+#define TREO680_STR_BASE 0xa2000000
+
+/* BACKLIGHT */
+#define TREO680_MAX_INTENSITY 254
+#define TREO680_DEFAULT_INTENSITY 160
+#define TREO680_LIMIT_MASK 0x7F
+#define TREO680_PRESCALER 63
+#define TREO680_PERIOD_NS 3500
+
+#endif
#include <linux/wm97xx_batt.h>
#include <linux/mtd/physmap.h>
#include <linux/usb/gpio_vbus.h>
+#include <linux/regulator/max1586.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
.batt_name = "mioa701_battery",
};
+/*
+ * Voltage regulation
+ */
+static struct regulator_consumer_supply max1586_consumers[] = {
+ {
+ .supply = "vcc_core",
+ }
+};
+
+static struct regulator_init_data max1586_v3_info = {
+ .constraints = {
+ .name = "vcc_core range",
+ .min_uV = 1000000,
+ .max_uV = 1705000,
+ .always_on = 1,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(max1586_consumers),
+ .consumer_supplies = max1586_consumers,
+};
+
+static struct max1586_subdev_data max1586_subdevs[] = {
+ { .name = "vcc_core", .id = MAX1586_V3,
+ .platform_data = &max1586_v3_info },
+};
+
+static struct max1586_platform_data max1586_info = {
+ .subdevs = max1586_subdevs,
+ .num_subdevs = ARRAY_SIZE(max1586_subdevs),
+ .v3_gain = MAX1586_GAIN_NO_R24, /* 700..1475 mV */
+};
+
/*
* Camera interface
*/
.mclk_10khz = 5000,
};
+static struct i2c_board_info __initdata mioa701_pi2c_devices[] = {
+ {
+ I2C_BOARD_INFO("max1586", 0x14),
+ .platform_data = &max1586_info,
+ },
+};
+
static struct soc_camera_link iclink = {
.bus_id = 0, /* Must match id in pxa27x_device_camera in device.c */
};
platform_add_devices(devices, ARRAY_SIZE(devices));
gsm_init();
+ i2c_register_board_info(1, ARRAY_AND_SIZE(mioa701_pi2c_devices));
pxa_set_i2c_info(&i2c_pdata);
+ pxa27x_set_i2c_power_info(NULL);
pxa_set_camera_info(&mioa701_pxacamera_platform_data);
i2c_register_board_info(0, ARRAY_AND_SIZE(mioa701_i2c_devices));
}
#include <linux/pda_power.h>
#include <linux/pwm_backlight.h>
#include <linux/gpio.h>
+#include <linux/wm97xx_batt.h>
#include <linux/power_supply.h>
+#include <linux/usb/gpio_vbus.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <mach/irda.h>
#include <mach/pxa27x_keypad.h>
#include <mach/udc.h>
+#include <mach/palmasoc.h>
+
#include <mach/pm.h>
#include "generic.h"
GPIO29_AC97_SDATA_IN_0,
GPIO30_AC97_SDATA_OUT,
GPIO31_AC97_SYNC,
+ GPIO89_AC97_SYSCLK,
+ GPIO113_AC97_nRESET,
/* IrDA */
GPIO49_GPIO, /* ir disable */
/* USB */
GPIO15_GPIO, /* usb detect */
- GPIO12_GPIO, /* usb pullup */
- GPIO95_GPIO, /* usb power */
+ GPIO95_GPIO, /* usb pullup */
/* Matrix keypad */
GPIO100_KP_MKIN_0 | WAKEUP_ON_LEVEL_HIGH,
}
};
+/******************************************************************************
+ * UDC
+ ******************************************************************************/
+static struct gpio_vbus_mach_info palmz72_udc_info = {
+ .gpio_vbus = GPIO_NR_PALMZ72_USB_DETECT_N,
+ .gpio_pullup = GPIO_NR_PALMZ72_USB_PULLUP,
+};
+
+static struct platform_device palmz72_gpio_vbus = {
+ .name = "gpio-vbus",
+ .id = -1,
+ .dev = {
+ .platform_data = &palmz72_udc_info,
+ },
+};
+
/******************************************************************************
* Power supply
******************************************************************************/
},
};
+/******************************************************************************
+ * WM97xx battery
+ ******************************************************************************/
+static struct wm97xx_batt_info wm97xx_batt_pdata = {
+ .batt_aux = WM97XX_AUX_ID3,
+ .temp_aux = WM97XX_AUX_ID2,
+ .charge_gpio = -1,
+ .max_voltage = PALMZ72_BAT_MAX_VOLTAGE,
+ .min_voltage = PALMZ72_BAT_MIN_VOLTAGE,
+ .batt_mult = 1000,
+ .batt_div = 414,
+ .temp_mult = 1,
+ .temp_div = 1,
+ .batt_tech = POWER_SUPPLY_TECHNOLOGY_LIPO,
+ .batt_name = "main-batt",
+};
+
+/******************************************************************************
+ * aSoC audio
+ ******************************************************************************/
+static struct platform_device palmz72_asoc = {
+ .name = "palm27x-asoc",
+ .id = -1,
+};
+
/******************************************************************************
* Framebuffer
******************************************************************************/
static struct platform_device *devices[] __initdata = {
&palmz72_backlight,
&palmz72_leds,
+ &palmz72_asoc,
&power_supply,
+ &palmz72_gpio_vbus,
};
+/* setup udc GPIOs initial state */
+static void __init palmz72_udc_init(void)
+{
+ if (!gpio_request(GPIO_NR_PALMZ72_USB_PULLUP, "USB Pullup")) {
+ gpio_direction_output(GPIO_NR_PALMZ72_USB_PULLUP, 0);
+ gpio_free(GPIO_NR_PALMZ72_USB_PULLUP);
+ }
+}
+
static void __init palmz72_init(void)
{
pxa2xx_mfp_config(ARRAY_AND_SIZE(palmz72_pin_config));
+
set_pxa_fb_info(&palmz72_lcd_screen);
pxa_set_mci_info(&palmz72_mci_platform_data);
+ palmz72_udc_init();
pxa_set_ac97_info(NULL);
pxa_set_ficp_info(&palmz72_ficp_platform_data);
pxa_set_keypad_info(&palmz72_keypad_platform_data);
+ wm97xx_bat_set_pdata(&wm97xx_batt_pdata);
+
platform_add_devices(devices, ARRAY_SIZE(devices));
}
#include <linux/delay.h>
#include <linux/mtd/physmap.h>
#include <linux/gpio.h>
+#include <linux/i2c.h>
#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
#include <linux/mtd/sharpsl.h>
&sharpsl_rom_device,
};
+static struct i2c_board_info __initdata poodle_i2c_devices[] = {
+ { I2C_BOARD_INFO("wm8731", 0x1b) },
+};
+
static void poodle_poweroff(void)
{
arm_machine_restart('h', NULL);
pxa_set_mci_info(&poodle_mci_platform_data);
pxa_set_ficp_info(&poodle_ficp_platform_data);
pxa_set_i2c_info(NULL);
+ i2c_register_board_info(0, ARRAY_AND_SIZE(poodle_i2c_devices));
poodle_init_spi();
}
--- /dev/null
+/*
+ * Hardware definitions for Palm Treo 680
+ *
+ * Author: Tomas Cech <sleep_walker@suse.cz>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * (find more info at www.hackndev.com)
+ *
+ */
+
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/irq.h>
+#include <linux/gpio_keys.h>
+#include <linux/input.h>
+#include <linux/pda_power.h>
+#include <linux/pwm_backlight.h>
+#include <linux/gpio.h>
+#include <linux/wm97xx_batt.h>
+#include <linux/power_supply.h>
+#include <linux/sysdev.h>
+#include <linux/w1-gpio.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include <mach/pxa27x.h>
+#include <mach/pxa27x-udc.h>
+#include <mach/audio.h>
+#include <mach/treo680.h>
+#include <mach/mmc.h>
+#include <mach/pxafb.h>
+#include <mach/irda.h>
+#include <mach/pxa27x_keypad.h>
+#include <mach/udc.h>
+#include <mach/ohci.h>
+#include <mach/pxa2xx-regs.h>
+#include <mach/palmasoc.h>
+#include <mach/camera.h>
+
+#include <sound/pxa2xx-lib.h>
+
+#include "generic.h"
+#include "devices.h"
+
+/******************************************************************************
+ * Pin configuration
+ ******************************************************************************/
+static unsigned long treo680_pin_config[] __initdata = {
+ /* MMC */
+ GPIO32_MMC_CLK,
+ GPIO92_MMC_DAT_0,
+ GPIO109_MMC_DAT_1,
+ GPIO110_MMC_DAT_2,
+ GPIO111_MMC_DAT_3,
+ GPIO112_MMC_CMD,
+ GPIO33_GPIO, /* SD read only */
+ GPIO113_GPIO, /* SD detect */
+
+ /* AC97 */
+ GPIO28_AC97_BITCLK,
+ GPIO29_AC97_SDATA_IN_0,
+ GPIO30_AC97_SDATA_OUT,
+ GPIO31_AC97_SYNC,
+ GPIO89_AC97_SYSCLK,
+ GPIO95_AC97_nRESET,
+
+ /* IrDA */
+ GPIO46_FICP_RXD,
+ GPIO47_FICP_TXD,
+
+ /* PWM */
+ GPIO16_PWM0_OUT,
+
+ /* USB */
+ GPIO1_GPIO | WAKEUP_ON_EDGE_BOTH, /* usb detect */
+
+ /* MATRIX KEYPAD */
+ GPIO100_KP_MKIN_0 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO101_KP_MKIN_1,
+ GPIO102_KP_MKIN_2,
+ GPIO97_KP_MKIN_3,
+ GPIO98_KP_MKIN_4,
+ GPIO99_KP_MKIN_5,
+ GPIO91_KP_MKIN_6,
+ GPIO13_KP_MKIN_7,
+ GPIO103_KP_MKOUT_0 | MFP_LPM_DRIVE_HIGH,
+ GPIO104_KP_MKOUT_1,
+ GPIO105_KP_MKOUT_2,
+ GPIO106_KP_MKOUT_3,
+ GPIO107_KP_MKOUT_4,
+ GPIO108_KP_MKOUT_5,
+ GPIO96_KP_MKOUT_6,
+ GPIO93_KP_DKIN_0 | WAKEUP_ON_LEVEL_HIGH, /* Hotsync button */
+
+ /* LCD */
+ GPIO58_LCD_LDD_0,
+ GPIO59_LCD_LDD_1,
+ GPIO60_LCD_LDD_2,
+ GPIO61_LCD_LDD_3,
+ GPIO62_LCD_LDD_4,
+ GPIO63_LCD_LDD_5,
+ GPIO64_LCD_LDD_6,
+ GPIO65_LCD_LDD_7,
+ GPIO66_LCD_LDD_8,
+ GPIO67_LCD_LDD_9,
+ GPIO68_LCD_LDD_10,
+ GPIO69_LCD_LDD_11,
+ GPIO70_LCD_LDD_12,
+ GPIO71_LCD_LDD_13,
+ GPIO72_LCD_LDD_14,
+ GPIO73_LCD_LDD_15,
+ GPIO74_LCD_FCLK,
+ GPIO75_LCD_LCLK,
+ GPIO76_LCD_PCLK,
+
+ /* Quick Capture Interface */
+ GPIO84_CIF_FV,
+ GPIO85_CIF_LV,
+ GPIO53_CIF_MCLK,
+ GPIO54_CIF_PCLK,
+ GPIO81_CIF_DD_0,
+ GPIO55_CIF_DD_1,
+ GPIO51_CIF_DD_2,
+ GPIO50_CIF_DD_3,
+ GPIO52_CIF_DD_4,
+ GPIO48_CIF_DD_5,
+ GPIO17_CIF_DD_6,
+ GPIO12_CIF_DD_7,
+
+ /* I2C */
+ GPIO117_I2C_SCL,
+ GPIO118_I2C_SDA,
+
+ /* GSM */
+ GPIO14_GPIO | WAKEUP_ON_EDGE_BOTH, /* GSM host wake up */
+ GPIO34_FFUART_RXD,
+ GPIO35_FFUART_CTS,
+ GPIO39_FFUART_TXD,
+ GPIO41_FFUART_RTS,
+
+ /* MISC. */
+ GPIO0_GPIO | WAKEUP_ON_EDGE_BOTH, /* external power detect */
+ GPIO15_GPIO | WAKEUP_ON_EDGE_BOTH, /* silent switch */
+ GPIO116_GPIO, /* headphone detect */
+ GPIO11_GPIO | WAKEUP_ON_EDGE_BOTH, /* bluetooth host wake up */
+};
+
+/******************************************************************************
+ * SD/MMC card controller
+ ******************************************************************************/
+static int treo680_mci_init(struct device *dev,
+ irq_handler_t treo680_detect_int, void *data)
+{
+ int err = 0;
+
+ /* Setup an interrupt for detecting card insert/remove events */
+ err = gpio_request(GPIO_NR_TREO680_SD_DETECT_N, "SD IRQ");
+
+ if (err)
+ goto err;
+
+ err = gpio_direction_input(GPIO_NR_TREO680_SD_DETECT_N);
+ if (err)
+ goto err2;
+
+ err = request_irq(gpio_to_irq(GPIO_NR_TREO680_SD_DETECT_N),
+ treo680_detect_int, IRQF_DISABLED | IRQF_SAMPLE_RANDOM |
+ IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
+ "SD/MMC card detect", data);
+
+ if (err) {
+ dev_err(dev, "%s: cannot request SD/MMC card detect IRQ\n",
+ __func__);
+ goto err2;
+ }
+
+ err = gpio_request(GPIO_NR_TREO680_SD_POWER, "SD_POWER");
+ if (err)
+ goto err3;
+
+ err = gpio_direction_output(GPIO_NR_TREO680_SD_POWER, 1);
+ if (err)
+ goto err4;
+
+ err = gpio_request(GPIO_NR_TREO680_SD_READONLY, "SD_READONLY");
+ if (err)
+ goto err4;
+
+ err = gpio_direction_input(GPIO_NR_TREO680_SD_READONLY);
+ if (err)
+ goto err5;
+
+ return 0;
+
+err5:
+ gpio_free(GPIO_NR_TREO680_SD_READONLY);
+err4:
+ gpio_free(GPIO_NR_TREO680_SD_POWER);
+err3:
+ free_irq(gpio_to_irq(GPIO_NR_TREO680_SD_DETECT_N), data);
+err2:
+ gpio_free(GPIO_NR_TREO680_SD_DETECT_N);
+err:
+ return err;
+}
+
+static void treo680_mci_exit(struct device *dev, void *data)
+{
+ gpio_free(GPIO_NR_TREO680_SD_READONLY);
+ gpio_free(GPIO_NR_TREO680_SD_POWER);
+ free_irq(gpio_to_irq(GPIO_NR_TREO680_SD_DETECT_N), data);
+ gpio_free(GPIO_NR_TREO680_SD_DETECT_N);
+}
+
+static void treo680_mci_power(struct device *dev, unsigned int vdd)
+{
+ struct pxamci_platform_data *p_d = dev->platform_data;
+ gpio_set_value(GPIO_NR_TREO680_SD_POWER, p_d->ocr_mask & (1 << vdd));
+}
+
+static int treo680_mci_get_ro(struct device *dev)
+{
+ return gpio_get_value(GPIO_NR_TREO680_SD_READONLY);
+}
+
+static struct pxamci_platform_data treo680_mci_platform_data = {
+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
+ .setpower = treo680_mci_power,
+ .get_ro = treo680_mci_get_ro,
+ .init = treo680_mci_init,
+ .exit = treo680_mci_exit,
+};
+
+/******************************************************************************
+ * GPIO keyboard
+ ******************************************************************************/
+static unsigned int treo680_matrix_keys[] = {
+ KEY(0, 0, KEY_F8), /* Red/Off/Power */
+ KEY(0, 1, KEY_LEFT),
+ KEY(0, 2, KEY_LEFTCTRL), /* Alternate */
+ KEY(0, 3, KEY_L),
+ KEY(0, 4, KEY_A),
+ KEY(0, 5, KEY_Q),
+ KEY(0, 6, KEY_P),
+
+ KEY(1, 0, KEY_RIGHTCTRL), /* Menu */
+ KEY(1, 1, KEY_RIGHT),
+ KEY(1, 2, KEY_LEFTSHIFT), /* Left shift */
+ KEY(1, 3, KEY_Z),
+ KEY(1, 4, KEY_S),
+ KEY(1, 5, KEY_W),
+
+ KEY(2, 0, KEY_F1), /* Phone */
+ KEY(2, 1, KEY_UP),
+ KEY(2, 2, KEY_0),
+ KEY(2, 3, KEY_X),
+ KEY(2, 4, KEY_D),
+ KEY(2, 5, KEY_E),
+
+ KEY(3, 0, KEY_F10), /* Calendar */
+ KEY(3, 1, KEY_DOWN),
+ KEY(3, 2, KEY_SPACE),
+ KEY(3, 3, KEY_C),
+ KEY(3, 4, KEY_F),
+ KEY(3, 5, KEY_R),
+
+ KEY(4, 0, KEY_F12), /* Mail */
+ KEY(4, 1, KEY_KPENTER),
+ KEY(4, 2, KEY_RIGHTALT), /* Alt */
+ KEY(4, 3, KEY_V),
+ KEY(4, 4, KEY_G),
+ KEY(4, 5, KEY_T),
+
+ KEY(5, 0, KEY_F9), /* Home */
+ KEY(5, 1, KEY_PAGEUP), /* Side up */
+ KEY(5, 2, KEY_DOT),
+ KEY(5, 3, KEY_B),
+ KEY(5, 4, KEY_H),
+ KEY(5, 5, KEY_Y),
+
+ KEY(6, 0, KEY_TAB), /* Side Activate */
+ KEY(6, 1, KEY_PAGEDOWN), /* Side down */
+ KEY(6, 2, KEY_ENTER),
+ KEY(6, 3, KEY_N),
+ KEY(6, 4, KEY_J),
+ KEY(6, 5, KEY_U),
+
+ KEY(7, 0, KEY_F6), /* Green/Call */
+ KEY(7, 1, KEY_O),
+ KEY(7, 2, KEY_BACKSPACE),
+ KEY(7, 3, KEY_M),
+ KEY(7, 4, KEY_K),
+ KEY(7, 5, KEY_I),
+};
+
+static struct pxa27x_keypad_platform_data treo680_keypad_platform_data = {
+ .matrix_key_rows = 8,
+ .matrix_key_cols = 7,
+ .matrix_key_map = treo680_matrix_keys,
+ .matrix_key_map_size = ARRAY_SIZE(treo680_matrix_keys),
+ .direct_key_map = { KEY_CONNECT },
+ .direct_key_num = 1,
+
+ .debounce_interval = 30,
+};
+
+/******************************************************************************
+ * aSoC audio
+ ******************************************************************************/
+
+static pxa2xx_audio_ops_t treo680_ac97_pdata = {
+ .reset_gpio = 95,
+};
+
+/******************************************************************************
+ * Backlight
+ ******************************************************************************/
+static int treo680_backlight_init(struct device *dev)
+{
+ int ret;
+
+ ret = gpio_request(GPIO_NR_TREO680_BL_POWER, "BL POWER");
+ if (ret)
+ goto err;
+ ret = gpio_direction_output(GPIO_NR_TREO680_BL_POWER, 0);
+ if (ret)
+ goto err2;
+ ret = gpio_request(GPIO_NR_TREO680_LCD_POWER, "LCD POWER");
+ if (ret)
+ goto err2;
+ ret = gpio_direction_output(GPIO_NR_TREO680_LCD_POWER, 0);
+ if (ret)
+ goto err3;
+
+ return 0;
+err3:
+ gpio_free(GPIO_NR_TREO680_LCD_POWER);
+err2:
+ gpio_free(GPIO_NR_TREO680_BL_POWER);
+err:
+ return ret;
+}
+
+static int treo680_backlight_notify(int brightness)
+{
+ gpio_set_value(GPIO_NR_TREO680_BL_POWER, brightness);
+ return TREO680_MAX_INTENSITY - brightness;
+};
+
+static void treo680_backlight_exit(struct device *dev)
+{
+ gpio_free(GPIO_NR_TREO680_BL_POWER);
+ gpio_free(GPIO_NR_TREO680_LCD_POWER);
+}
+
+static struct platform_pwm_backlight_data treo680_backlight_data = {
+ .pwm_id = 0,
+ .max_brightness = TREO680_MAX_INTENSITY,
+ .dft_brightness = TREO680_DEFAULT_INTENSITY,
+ .pwm_period_ns = TREO680_PERIOD_NS,
+ .init = treo680_backlight_init,
+ .notify = treo680_backlight_notify,
+ .exit = treo680_backlight_exit,
+};
+
+static struct platform_device treo680_backlight = {
+ .name = "pwm-backlight",
+ .dev = {
+ .parent = &pxa27x_device_pwm0.dev,
+ .platform_data = &treo680_backlight_data,
+ },
+};
+
+/******************************************************************************
+ * IrDA
+ ******************************************************************************/
+static void treo680_transceiver_mode(struct device *dev, int mode)
+{
+ gpio_set_value(GPIO_NR_TREO680_IR_EN, mode & IR_OFF);
+ pxa2xx_transceiver_mode(dev, mode);
+}
+
+static int treo680_irda_startup(struct device *dev)
+{
+ int err;
+
+ err = gpio_request(GPIO_NR_TREO680_IR_EN, "Ir port disable");
+ if (err)
+ goto err1;
+
+ err = gpio_direction_output(GPIO_NR_TREO680_IR_EN, 1);
+ if (err)
+ goto err2;
+
+ return 0;
+
+err2:
+ dev_err(dev, "treo680_irda: cannot change IR gpio direction\n");
+ gpio_free(GPIO_NR_TREO680_IR_EN);
+err1:
+ dev_err(dev, "treo680_irda: cannot allocate IR gpio\n");
+ return err;
+}
+
+static void treo680_irda_shutdown(struct device *dev)
+{
+ gpio_free(GPIO_NR_TREO680_AMP_EN);
+}
+
+static struct pxaficp_platform_data treo680_ficp_info = {
+ .transceiver_cap = IR_FIRMODE | IR_SIRMODE | IR_OFF,
+ .startup = treo680_irda_startup,
+ .shutdown = treo680_irda_shutdown,
+ .transceiver_mode = treo680_transceiver_mode,
+};
+
+/******************************************************************************
+ * UDC
+ ******************************************************************************/
+static struct pxa2xx_udc_mach_info treo680_udc_info __initdata = {
+ .gpio_vbus = GPIO_NR_TREO680_USB_DETECT,
+ .gpio_vbus_inverted = 1,
+ .gpio_pullup = GPIO_NR_TREO680_USB_PULLUP,
+};
+
+
+/******************************************************************************
+ * USB host
+ ******************************************************************************/
+static struct pxaohci_platform_data treo680_ohci_info = {
+ .port_mode = PMM_PERPORT_MODE,
+ .flags = ENABLE_PORT1 | ENABLE_PORT3,
+ .power_budget = 0,
+};
+
+/******************************************************************************
+ * Power supply
+ ******************************************************************************/
+static int power_supply_init(struct device *dev)
+{
+ int ret;
+
+ ret = gpio_request(GPIO_NR_TREO680_POWER_DETECT, "CABLE_STATE_AC");
+ if (ret)
+ goto err1;
+ ret = gpio_direction_input(GPIO_NR_TREO680_POWER_DETECT);
+ if (ret)
+ goto err2;
+
+ return 0;
+
+err2:
+ gpio_free(GPIO_NR_TREO680_POWER_DETECT);
+err1:
+ return ret;
+}
+
+static int treo680_is_ac_online(void)
+{
+ return gpio_get_value(GPIO_NR_TREO680_POWER_DETECT);
+}
+
+static void power_supply_exit(struct device *dev)
+{
+ gpio_free(GPIO_NR_TREO680_POWER_DETECT);
+}
+
+static char *treo680_supplicants[] = {
+ "main-battery",
+};
+
+static struct pda_power_pdata power_supply_info = {
+ .init = power_supply_init,
+ .is_ac_online = treo680_is_ac_online,
+ .exit = power_supply_exit,
+ .supplied_to = treo680_supplicants,
+ .num_supplicants = ARRAY_SIZE(treo680_supplicants),
+};
+
+static struct platform_device power_supply = {
+ .name = "pda-power",
+ .id = -1,
+ .dev = {
+ .platform_data = &power_supply_info,
+ },
+};
+
+/******************************************************************************
+ * Vibra and LEDs
+ ******************************************************************************/
+static struct gpio_led gpio_leds[] = {
+ {
+ .name = "treo680:vibra:vibra",
+ .default_trigger = "none",
+ .gpio = GPIO_NR_TREO680_VIBRATE_EN,
+ },
+ {
+ .name = "treo680:green:led",
+ .default_trigger = "mmc0",
+ .gpio = GPIO_NR_TREO680_GREEN_LED,
+ },
+ {
+ .name = "treo680:keybbl:keybbl",
+ .default_trigger = "none",
+ .gpio = GPIO_NR_TREO680_KEYB_BL,
+ },
+};
+
+static struct gpio_led_platform_data gpio_led_info = {
+ .leds = gpio_leds,
+ .num_leds = ARRAY_SIZE(gpio_leds),
+};
+
+static struct platform_device treo680_leds = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev = {
+ .platform_data = &gpio_led_info,
+ }
+};
+
+
+/******************************************************************************
+ * Framebuffer
+ ******************************************************************************/
+/* TODO: add support for 324x324 */
+static struct pxafb_mode_info treo680_lcd_modes[] = {
+{
+ .pixclock = 86538,
+ .xres = 320,
+ .yres = 320,
+ .bpp = 16,
+
+ .left_margin = 20,
+ .right_margin = 8,
+ .upper_margin = 8,
+ .lower_margin = 5,
+
+ .hsync_len = 4,
+ .vsync_len = 1,
+},
+};
+
+static struct pxafb_mach_info treo680_lcd_screen = {
+ .modes = treo680_lcd_modes,
+ .num_modes = ARRAY_SIZE(treo680_lcd_modes),
+ .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL,
+};
+
+/******************************************************************************
+ * Power management - standby
+ ******************************************************************************/
+static void __init treo680_pm_init(void)
+{
+ static u32 resume[] = {
+ 0xe3a00101, /* mov r0, #0x40000000 */
+ 0xe380060f, /* orr r0, r0, #0x00f00000 */
+ 0xe590f008, /* ldr pc, [r0, #0x08] */
+ };
+
+ /* this is where the bootloader jumps */
+ memcpy(phys_to_virt(TREO680_STR_BASE), resume, sizeof(resume));
+}
+
+/******************************************************************************
+ * Machine init
+ ******************************************************************************/
+static struct platform_device *devices[] __initdata = {
+ &treo680_backlight,
+ &treo680_leds,
+ &power_supply,
+};
+
+/* setup udc GPIOs initial state */
+static void __init treo680_udc_init(void)
+{
+ if (!gpio_request(GPIO_NR_TREO680_USB_PULLUP, "UDC Vbus")) {
+ gpio_direction_output(GPIO_NR_TREO680_USB_PULLUP, 1);
+ gpio_free(GPIO_NR_TREO680_USB_PULLUP);
+ }
+}
+
+static void __init treo680_init(void)
+{
+ treo680_pm_init();
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(treo680_pin_config));
+ pxa_set_keypad_info(&treo680_keypad_platform_data);
+ set_pxa_fb_info(&treo680_lcd_screen);
+ pxa_set_mci_info(&treo680_mci_platform_data);
+ treo680_udc_init();
+ pxa_set_udc_info(&treo680_udc_info);
+ pxa_set_ac97_info(&treo680_ac97_pdata);
+ pxa_set_ficp_info(&treo680_ficp_info);
+ pxa_set_ohci_info(&treo680_ohci_info);
+
+ platform_add_devices(devices, ARRAY_SIZE(devices));
+}
+
+MACHINE_START(TREO680, "Palm Treo 680")
+ .phys_io = TREO680_PHYS_IO_START,
+ .io_pg_offst = io_p2v(0x40000000),
+ .boot_params = 0xa0000100,
+ .map_io = pxa_map_io,
+ .init_irq = pxa27x_init_irq,
+ .timer = &pxa_timer,
+ .init_machine = treo680_init,
+MACHINE_END
#include <asm/irq.h>
#include <asm/leds.h>
#include <asm/mach-types.h>
+#include <asm/smp_twd.h>
#include <asm/hardware/gic.h>
#include <asm/hardware/cache-l2x0.h>
#include <linux/timer.h>
#include <linux/init.h>
#include <linux/device.h>
-#include <linux/gpio.h>
#include <linux/io.h>
#include <asm/mach/arch.h>
help
Say Y here if you are using the AT2440EVB development board
+config MACH_MINI2440
+ bool "MINI2440 development board"
+ select CPU_S3C2440
+ select EEPROM_AT24
+ select LEDS_TRIGGER_BACKLIGHT
+ select SND_S3C24XX_SOC_S3C24XX_UDA134X
+ help
+ Say Y here to select support for the MINI2440. Is a 10cm x 10cm board
+ available via various sources. It can come with a 3.5" or 7" touch LCD.
+
endmenu
obj-$(CONFIG_ARCH_S3C2440) += mach-smdk2440.o
obj-$(CONFIG_MACH_NEXCODER_2440) += mach-nexcoder.o
obj-$(CONFIG_MACH_AT2440EVB) += mach-at2440evb.o
+obj-$(CONFIG_MACH_MINI2440) += mach-mini2440.o
--- /dev/null
+/* linux/arch/arm/mach-s3c2440/mach-mini2440.c
+ *
+ * Copyright (c) 2008 Ramax Lo <ramaxlo@gmail.com>
+ * Based on mach-anubis.c by Ben Dooks <ben@simtec.co.uk>
+ * and modifications by SBZ <sbz@spgui.org> and
+ * Weibing <http://weibing.blogbus.com> and
+ * Michel Pollet <buserror@gmail.com>
+ *
+ * For product information, visit http://code.google.com/p/mini2440/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/timer.h>
+#include <linux/init.h>
+#include <linux/gpio.h>
+#include <linux/input.h>
+#include <linux/io.h>
+#include <linux/serial_core.h>
+#include <linux/dm9000.h>
+#include <linux/i2c/at24.h>
+#include <linux/platform_device.h>
+#include <linux/gpio_keys.h>
+#include <linux/i2c.h>
+#include <linux/mmc/host.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include <mach/hardware.h>
+#include <mach/fb.h>
+#include <asm/mach-types.h>
+
+#include <plat/regs-serial.h>
+#include <mach/regs-gpio.h>
+#include <mach/leds-gpio.h>
+#include <mach/regs-mem.h>
+#include <mach/regs-lcd.h>
+#include <mach/irqs.h>
+#include <plat/nand.h>
+#include <plat/iic.h>
+#include <plat/mci.h>
+#include <plat/udc.h>
+
+#include <plat/regs-serial.h>
+
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/nand_ecc.h>
+#include <linux/mtd/partitions.h>
+
+#include <plat/clock.h>
+#include <plat/devs.h>
+#include <plat/cpu.h>
+
+#include <sound/s3c24xx_uda134x.h>
+
+#define MACH_MINI2440_DM9K_BASE (S3C2410_CS4 + 0x300)
+
+static struct map_desc mini2440_iodesc[] __initdata = {
+ /* nothing to declare, move along */
+};
+
+#define UCON S3C2410_UCON_DEFAULT
+#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB
+#define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE
+
+
+static struct s3c2410_uartcfg mini2440_uartcfgs[] __initdata = {
+ [0] = {
+ .hwport = 0,
+ .flags = 0,
+ .ucon = UCON,
+ .ulcon = ULCON,
+ .ufcon = UFCON,
+ },
+ [1] = {
+ .hwport = 1,
+ .flags = 0,
+ .ucon = UCON,
+ .ulcon = ULCON,
+ .ufcon = UFCON,
+ },
+ [2] = {
+ .hwport = 2,
+ .flags = 0,
+ .ucon = UCON,
+ .ulcon = ULCON,
+ .ufcon = UFCON,
+ },
+};
+
+/* USB device UDC support */
+
+static void mini2440_udc_pullup(enum s3c2410_udc_cmd_e cmd)
+{
+ pr_debug("udc: pullup(%d)\n", cmd);
+
+ switch (cmd) {
+ case S3C2410_UDC_P_ENABLE :
+ s3c2410_gpio_setpin(S3C2410_GPC(5), 1);
+ break;
+ case S3C2410_UDC_P_DISABLE :
+ s3c2410_gpio_setpin(S3C2410_GPC(5), 0);
+ break;
+ case S3C2410_UDC_P_RESET :
+ break;
+ default:
+ break;
+ }
+}
+
+static struct s3c2410_udc_mach_info mini2440_udc_cfg __initdata = {
+ .udc_command = mini2440_udc_pullup,
+};
+
+
+/* LCD timing and setup */
+
+/*
+ * This macro simplifies the table bellow
+ */
+#define _LCD_DECLARE(_clock,_xres,margin_left,margin_right,hsync, \
+ _yres,margin_top,margin_bottom,vsync, refresh) \
+ .width = _xres, \
+ .xres = _xres, \
+ .height = _yres, \
+ .yres = _yres, \
+ .left_margin = margin_left, \
+ .right_margin = margin_right, \
+ .upper_margin = margin_top, \
+ .lower_margin = margin_bottom, \
+ .hsync_len = hsync, \
+ .vsync_len = vsync, \
+ .pixclock = ((_clock*100000000000LL) / \
+ ((refresh) * \
+ (hsync + margin_left + _xres + margin_right) * \
+ (vsync + margin_top + _yres + margin_bottom))), \
+ .bpp = 16,\
+ .type = (S3C2410_LCDCON1_TFT16BPP |\
+ S3C2410_LCDCON1_TFT)
+
+struct s3c2410fb_display mini2440_lcd_cfg[] __initdata = {
+ [0] = { /* mini2440 + 3.5" TFT + touchscreen */
+ _LCD_DECLARE(
+ 7, /* The 3.5 is quite fast */
+ 240, 21, 38, 6, /* x timing */
+ 320, 4, 4, 2, /* y timing */
+ 60), /* refresh rate */
+ .lcdcon5 = (S3C2410_LCDCON5_FRM565 |
+ S3C2410_LCDCON5_INVVLINE |
+ S3C2410_LCDCON5_INVVFRAME |
+ S3C2410_LCDCON5_INVVDEN |
+ S3C2410_LCDCON5_PWREN),
+ },
+ [1] = { /* mini2440 + 7" TFT + touchscreen */
+ _LCD_DECLARE(
+ 10, /* the 7" runs slower */
+ 800, 40, 40, 48, /* x timing */
+ 480, 29, 3, 3, /* y timing */
+ 50), /* refresh rate */
+ .lcdcon5 = (S3C2410_LCDCON5_FRM565 |
+ S3C2410_LCDCON5_INVVLINE |
+ S3C2410_LCDCON5_INVVFRAME |
+ S3C2410_LCDCON5_PWREN),
+ },
+ /* The VGA shield can outout at several resolutions. All share
+ * the same timings, however, anything smaller than 1024x768
+ * will only be displayed in the top left corner of a 1024x768
+ * XGA output unless you add optional dip switches to the shield.
+ * Therefore timings for other resolutions have been ommited here.
+ */
+ [2] = {
+ _LCD_DECLARE(
+ 10,
+ 1024, 1, 2, 2, /* y timing */
+ 768, 200, 16, 16, /* x timing */
+ 24), /* refresh rate, maximum stable,
+ tested with the FPGA shield */
+ .lcdcon5 = (S3C2410_LCDCON5_FRM565 |
+ S3C2410_LCDCON5_HWSWP),
+ },
+};
+
+/* todo - put into gpio header */
+
+#define S3C2410_GPCCON_MASK(x) (3 << ((x) * 2))
+#define S3C2410_GPDCON_MASK(x) (3 << ((x) * 2))
+
+struct s3c2410fb_mach_info mini2440_fb_info __initdata = {
+ .displays = &mini2440_lcd_cfg[0], /* not constant! see init */
+ .num_displays = 1,
+ .default_display = 0,
+
+ /* Enable VD[2..7], VD[10..15], VD[18..23] and VCLK, syncs, VDEN
+ * and disable the pull down resistors on pins we are using for LCD
+ * data. */
+
+ .gpcup = (0xf << 1) | (0x3f << 10),
+
+ .gpccon = (S3C2410_GPC1_VCLK | S3C2410_GPC2_VLINE |
+ S3C2410_GPC3_VFRAME | S3C2410_GPC4_VM |
+ S3C2410_GPC10_VD2 | S3C2410_GPC11_VD3 |
+ S3C2410_GPC12_VD4 | S3C2410_GPC13_VD5 |
+ S3C2410_GPC14_VD6 | S3C2410_GPC15_VD7),
+
+ .gpccon_mask = (S3C2410_GPCCON_MASK(1) | S3C2410_GPCCON_MASK(2) |
+ S3C2410_GPCCON_MASK(3) | S3C2410_GPCCON_MASK(4) |
+ S3C2410_GPCCON_MASK(10) | S3C2410_GPCCON_MASK(11) |
+ S3C2410_GPCCON_MASK(12) | S3C2410_GPCCON_MASK(13) |
+ S3C2410_GPCCON_MASK(14) | S3C2410_GPCCON_MASK(15)),
+
+ .gpdup = (0x3f << 2) | (0x3f << 10),
+
+ .gpdcon = (S3C2410_GPD2_VD10 | S3C2410_GPD3_VD11 |
+ S3C2410_GPD4_VD12 | S3C2410_GPD5_VD13 |
+ S3C2410_GPD6_VD14 | S3C2410_GPD7_VD15 |
+ S3C2410_GPD10_VD18 | S3C2410_GPD11_VD19 |
+ S3C2410_GPD12_VD20 | S3C2410_GPD13_VD21 |
+ S3C2410_GPD14_VD22 | S3C2410_GPD15_VD23),
+
+ .gpdcon_mask = (S3C2410_GPDCON_MASK(2) | S3C2410_GPDCON_MASK(3) |
+ S3C2410_GPDCON_MASK(4) | S3C2410_GPDCON_MASK(5) |
+ S3C2410_GPDCON_MASK(6) | S3C2410_GPDCON_MASK(7) |
+ S3C2410_GPDCON_MASK(10) | S3C2410_GPDCON_MASK(11)|
+ S3C2410_GPDCON_MASK(12) | S3C2410_GPDCON_MASK(13)|
+ S3C2410_GPDCON_MASK(14) | S3C2410_GPDCON_MASK(15)),
+};
+
+/* MMC/SD */
+
+static struct s3c24xx_mci_pdata mini2440_mmc_cfg __initdata = {
+ .gpio_detect = S3C2410_GPG(8),
+ .gpio_wprotect = S3C2410_GPH(8),
+ .set_power = NULL,
+ .ocr_avail = MMC_VDD_32_33|MMC_VDD_33_34,
+};
+
+/* NAND Flash on MINI2440 board */
+
+static struct mtd_partition mini2440_default_nand_part[] __initdata = {
+ [0] = {
+ .name = "u-boot",
+ .size = SZ_256K,
+ .offset = 0,
+ },
+ [1] = {
+ .name = "u-boot-env",
+ .size = SZ_128K,
+ .offset = SZ_256K,
+ },
+ [2] = {
+ .name = "kernel",
+ /* 5 megabytes, for a kernel with no modules
+ * or a uImage with a ramdisk attached */
+ .size = 0x00500000,
+ .offset = SZ_256K + SZ_128K,
+ },
+ [3] = {
+ .name = "root",
+ .offset = SZ_256K + SZ_128K + 0x00500000,
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+static struct s3c2410_nand_set mini2440_nand_sets[] __initdata = {
+ [0] = {
+ .name = "nand",
+ .nr_chips = 1,
+ .nr_partitions = ARRAY_SIZE(mini2440_default_nand_part),
+ .partitions = mini2440_default_nand_part,
+ },
+};
+
+static struct s3c2410_platform_nand mini2440_nand_info __initdata = {
+ .tacls = 0,
+ .twrph0 = 25,
+ .twrph1 = 15,
+ .nr_sets = ARRAY_SIZE(mini2440_nand_sets),
+ .sets = mini2440_nand_sets,
+ .ignore_unset_ecc = 1,
+};
+
+/* DM9000AEP 10/100 ethernet controller */
+
+static struct resource mini2440_dm9k_resource[] __initdata = {
+ [0] = {
+ .start = MACH_MINI2440_DM9K_BASE,
+ .end = MACH_MINI2440_DM9K_BASE + 3,
+ .flags = IORESOURCE_MEM
+ },
+ [1] = {
+ .start = MACH_MINI2440_DM9K_BASE + 4,
+ .end = MACH_MINI2440_DM9K_BASE + 7,
+ .flags = IORESOURCE_MEM
+ },
+ [2] = {
+ .start = IRQ_EINT7,
+ .end = IRQ_EINT7,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
+ }
+};
+
+/*
+ * The DM9000 has no eeprom, and it's MAC address is set by
+ * the bootloader before starting the kernel.
+ */
+static struct dm9000_plat_data mini2440_dm9k_pdata __initdata = {
+ .flags = (DM9000_PLATF_16BITONLY | DM9000_PLATF_NO_EEPROM),
+};
+
+static struct platform_device mini2440_device_eth __initdata = {
+ .name = "dm9000",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(mini2440_dm9k_resource),
+ .resource = mini2440_dm9k_resource,
+ .dev = {
+ .platform_data = &mini2440_dm9k_pdata,
+ },
+};
+
+/* CON5
+ * +--+ /-----\
+ * | | | |
+ * | | | BAT |
+ * | | \_____/
+ * | |
+ * | | +----+ +----+
+ * | | | K5 | | K1 |
+ * | | +----+ +----+
+ * | | +----+ +----+
+ * | | | K4 | | K2 |
+ * | | +----+ +----+
+ * | | +----+ +----+
+ * | | | K6 | | K3 |
+ * | | +----+ +----+
+ * .....
+ */
+static struct gpio_keys_button mini2440_buttons[] __initdata = {
+ {
+ .gpio = S3C2410_GPG(0), /* K1 */
+ .code = KEY_F1,
+ .desc = "Button 1",
+ .active_low = 1,
+ },
+ {
+ .gpio = S3C2410_GPG(3), /* K2 */
+ .code = KEY_F2,
+ .desc = "Button 2",
+ .active_low = 1,
+ },
+ {
+ .gpio = S3C2410_GPG(5), /* K3 */
+ .code = KEY_F3,
+ .desc = "Button 3",
+ .active_low = 1,
+ },
+ {
+ .gpio = S3C2410_GPG(6), /* K4 */
+ .code = KEY_POWER,
+ .desc = "Power",
+ .active_low = 1,
+ },
+ {
+ .gpio = S3C2410_GPG(7), /* K5 */
+ .code = KEY_F5,
+ .desc = "Button 5",
+ .active_low = 1,
+ },
+#if 0
+ /* this pin is also known as TCLK1 and seems to already
+ * marked as "in use" somehow in the kernel -- possibly wrongly */
+ {
+ .gpio = S3C2410_GPG(11), /* K6 */
+ .code = KEY_F6,
+ .desc = "Button 6",
+ .active_low = 1,
+ },
+#endif
+};
+
+static struct gpio_keys_platform_data mini2440_button_data __initdata = {
+ .buttons = mini2440_buttons,
+ .nbuttons = ARRAY_SIZE(mini2440_buttons),
+};
+
+static struct platform_device mini2440_button_device __initdata = {
+ .name = "gpio-keys",
+ .id = -1,
+ .dev = {
+ .platform_data = &mini2440_button_data,
+ }
+};
+
+/* LEDS */
+
+static struct s3c24xx_led_platdata mini2440_led1_pdata __initdata = {
+ .name = "led1",
+ .gpio = S3C2410_GPB(5),
+ .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE,
+ .def_trigger = "heartbeat",
+};
+
+static struct s3c24xx_led_platdata mini2440_led2_pdata __initdata = {
+ .name = "led2",
+ .gpio = S3C2410_GPB(6),
+ .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE,
+ .def_trigger = "nand-disk",
+};
+
+static struct s3c24xx_led_platdata mini2440_led3_pdata __initdata = {
+ .name = "led3",
+ .gpio = S3C2410_GPB(7),
+ .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE,
+ .def_trigger = "mmc0",
+};
+
+static struct s3c24xx_led_platdata mini2440_led4_pdata __initdata = {
+ .name = "led4",
+ .gpio = S3C2410_GPB(8),
+ .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE,
+ .def_trigger = "",
+};
+
+static struct s3c24xx_led_platdata mini2440_led_backlight_pdata __initdata = {
+ .name = "backlight",
+ .gpio = S3C2410_GPG(4),
+ .def_trigger = "backlight",
+};
+
+static struct platform_device mini2440_led1 __initdata = {
+ .name = "s3c24xx_led",
+ .id = 1,
+ .dev = {
+ .platform_data = &mini2440_led1_pdata,
+ },
+};
+
+static struct platform_device mini2440_led2 __initdata = {
+ .name = "s3c24xx_led",
+ .id = 2,
+ .dev = {
+ .platform_data = &mini2440_led2_pdata,
+ },
+};
+
+static struct platform_device mini2440_led3 __initdata = {
+ .name = "s3c24xx_led",
+ .id = 3,
+ .dev = {
+ .platform_data = &mini2440_led3_pdata,
+ },
+};
+
+static struct platform_device mini2440_led4 __initdata = {
+ .name = "s3c24xx_led",
+ .id = 4,
+ .dev = {
+ .platform_data = &mini2440_led4_pdata,
+ },
+};
+
+static struct platform_device mini2440_led_backlight __initdata = {
+ .name = "s3c24xx_led",
+ .id = 5,
+ .dev = {
+ .platform_data = &mini2440_led_backlight_pdata,
+ },
+};
+
+/* AUDIO */
+
+static struct s3c24xx_uda134x_platform_data mini2440_audio_pins __initdata = {
+ .l3_clk = S3C2410_GPB(4),
+ .l3_mode = S3C2410_GPB(2),
+ .l3_data = S3C2410_GPB(3),
+ .model = UDA134X_UDA1341
+};
+
+static struct platform_device mini2440_audio __initdata = {
+ .name = "s3c24xx_uda134x",
+ .id = 0,
+ .dev = {
+ .platform_data = &mini2440_audio_pins,
+ },
+};
+
+/*
+ * I2C devices
+ */
+static struct at24_platform_data at24c08 = {
+ .byte_len = SZ_8K / 8,
+ .page_size = 16,
+};
+
+static struct i2c_board_info mini2440_i2c_devs[] __initdata = {
+ {
+ I2C_BOARD_INFO("24c08", 0x50),
+ .platform_data = &at24c08,
+ },
+};
+
+static struct platform_device *mini2440_devices[] __initdata = {
+ &s3c_device_usb,
+ &s3c_device_wdt,
+/* &s3c_device_adc,*/ /* ADC doesn't like living with touchscreen ! */
+ &s3c_device_i2c0,
+ &s3c_device_rtc,
+ &s3c_device_usbgadget,
+ &mini2440_device_eth,
+ &mini2440_led1,
+ &mini2440_led2,
+ &mini2440_led3,
+ &mini2440_led4,
+ &mini2440_button_device,
+ &s3c_device_nand,
+ &s3c_device_sdi,
+ &s3c_device_iis,
+ &mini2440_audio,
+/* &s3c_device_timer[0],*/ /* buzzer pwm, no API for it */
+ /* remaining devices are optional */
+};
+
+static void __init mini2440_map_io(void)
+{
+ s3c24xx_init_io(mini2440_iodesc, ARRAY_SIZE(mini2440_iodesc));
+ s3c24xx_init_clocks(12000000);
+ s3c24xx_init_uarts(mini2440_uartcfgs, ARRAY_SIZE(mini2440_uartcfgs));
+
+ s3c_device_nand.dev.platform_data = &mini2440_nand_info;
+ s3c_device_sdi.dev.platform_data = &mini2440_mmc_cfg;
+}
+
+/*
+ * mini2440_features string
+ *
+ * t = Touchscreen present
+ * b = backlight control
+ * c = camera [TODO]
+ * 0-9 LCD configuration
+ *
+ */
+static char mini2440_features_str[12] __initdata = "0tb";
+
+static int __init mini2440_features_setup(char *str)
+{
+ if (str)
+ strlcpy(mini2440_features_str, str, sizeof(mini2440_features_str));
+ return 1;
+}
+
+__setup("mini2440=", mini2440_features_setup);
+
+#define FEATURE_SCREEN (1 << 0)
+#define FEATURE_BACKLIGHT (1 << 1)
+#define FEATURE_TOUCH (1 << 2)
+#define FEATURE_CAMERA (1 << 3)
+
+struct mini2440_features_t {
+ int count;
+ int done;
+ int lcd_index;
+ struct platform_device *optional[8];
+};
+
+static void mini2440_parse_features(
+ struct mini2440_features_t * features,
+ const char * features_str )
+{
+ const char * fp = features_str;
+
+ features->count = 0;
+ features->done = 0;
+ features->lcd_index = -1;
+
+ while (*fp) {
+ char f = *fp++;
+
+ switch (f) {
+ case '0'...'9': /* tft screen */
+ if (features->done & FEATURE_SCREEN) {
+ printk(KERN_INFO "MINI2440: '%c' ignored, "
+ "screen type already set\n", f);
+ } else {
+ int li = f - '0';
+ if (li >= ARRAY_SIZE(mini2440_lcd_cfg))
+ printk(KERN_INFO "MINI2440: "
+ "'%c' out of range LCD mode\n", f);
+ else {
+ features->optional[features->count++] =
+ &s3c_device_lcd;
+ features->lcd_index = li;
+ }
+ }
+ features->done |= FEATURE_SCREEN;
+ break;
+ case 'b':
+ if (features->done & FEATURE_BACKLIGHT)
+ printk(KERN_INFO "MINI2440: '%c' ignored, "
+ "backlight already set\n", f);
+ else {
+ features->optional[features->count++] =
+ &mini2440_led_backlight;
+ }
+ features->done |= FEATURE_BACKLIGHT;
+ break;
+ case 't':
+ printk(KERN_INFO "MINI2440: '%c' ignored, "
+ "touchscreen not compiled in\n", f);
+ break;
+ case 'c':
+ if (features->done & FEATURE_CAMERA)
+ printk(KERN_INFO "MINI2440: '%c' ignored, "
+ "camera already registered\n", f);
+ else
+ features->optional[features->count++] =
+ &s3c_device_camif;
+ features->done |= FEATURE_CAMERA;
+ break;
+ }
+ }
+}
+
+static void __init mini2440_init(void)
+{
+ struct mini2440_features_t features = { 0 };
+ int i;
+
+ printk(KERN_INFO "MINI2440: Option string mini2440=%s\n",
+ mini2440_features_str);
+
+ /* Parse the feature string */
+ mini2440_parse_features(&features, mini2440_features_str);
+
+ /* turn LCD on */
+ s3c2410_gpio_cfgpin(S3C2410_GPC(0), S3C2410_GPC0_LEND);
+
+ /* Turn the backlight early on */
+ s3c2410_gpio_setpin(S3C2410_GPG(4), 1);
+ s3c2410_gpio_cfgpin(S3C2410_GPG(4), S3C2410_GPIO_OUTPUT);
+
+ /* remove pullup on optional PWM backlight -- unused on 3.5 and 7"s */
+ s3c2410_gpio_pullup(S3C2410_GPB(1), 0);
+ s3c2410_gpio_setpin(S3C2410_GPB(1), 0);
+ s3c2410_gpio_cfgpin(S3C2410_GPB(1), S3C2410_GPIO_INPUT);
+
+ /* Make sure the D+ pullup pin is output */
+ s3c2410_gpio_cfgpin(S3C2410_GPC(5), S3C2410_GPIO_OUTPUT);
+
+ /* mark the key as input, without pullups (there is one on the board) */
+ for (i = 0; i < ARRAY_SIZE(mini2440_buttons); i++) {
+ s3c2410_gpio_pullup(mini2440_buttons[i].gpio, 0);
+ s3c2410_gpio_cfgpin(mini2440_buttons[i].gpio,
+ S3C2410_GPIO_INPUT);
+ }
+ if (features.lcd_index != -1) {
+ int li;
+
+ mini2440_fb_info.displays =
+ &mini2440_lcd_cfg[features.lcd_index];
+
+ printk(KERN_INFO "MINI2440: LCD");
+ for (li = 0; li < ARRAY_SIZE(mini2440_lcd_cfg); li++)
+ if (li == features.lcd_index)
+ printk(" [%d:%dx%d]", li,
+ mini2440_lcd_cfg[li].width,
+ mini2440_lcd_cfg[li].height);
+ else
+ printk(" %d:%dx%d", li,
+ mini2440_lcd_cfg[li].width,
+ mini2440_lcd_cfg[li].height);
+ printk("\n");
+ s3c24xx_fb_set_platdata(&mini2440_fb_info);
+ }
+ s3c24xx_udc_set_platdata(&mini2440_udc_cfg);
+ s3c_i2c0_set_platdata(NULL);
+ i2c_register_board_info(0, mini2440_i2c_devs,
+ ARRAY_SIZE(mini2440_i2c_devs));
+
+ platform_add_devices(mini2440_devices, ARRAY_SIZE(mini2440_devices));
+
+ if (features.count) /* the optional features */
+ platform_add_devices(features.optional, features.count);
+
+}
+
+
+MACHINE_START(MINI2440, "MINI2440")
+ /* Maintainer: Michel Pollet <buserror@gmail.com> */
+ .phys_io = S3C2410_PA_UART,
+ .io_pg_offst = (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc,
+ .boot_params = S3C2410_SDRAM_PA + 0x100,
+ .map_io = mini2440_map_io,
+ .init_machine = mini2440_init,
+ .init_irq = s3c24xx_init_irq,
+ .timer = &s3c24xx_timer,
+MACHINE_END
depends on ARCH_S3C2440
select CPU_S3C2442
+config MACH_NEO1973_GTA02
+ bool "Openmoko GTA02 / Freerunner phone"
+ select CPU_S3C2442
+ select MFD_PCF50633
+ select PCF50633_GPIO
+ select I2C
+ select POWER_SUPPLY
+ select MACH_NEO1973
+ select S3C2410_PWM
+ help
+ Say Y here if you are using the Openmoko GTA02 / Freerunner GSM Phone
+
endmenu
obj-$(CONFIG_CPU_S3C2442) += s3c2442.o
obj-$(CONFIG_CPU_S3C2442) += clock.o
+obj-$(CONFIG_MACH_NEO1973_GTA02) += mach-gta02.o
+
# Machine support
--- /dev/null
+#ifndef _GTA02_H
+#define _GTA02_H
+
+#include <mach/regs-gpio.h>
+
+/* Different hardware revisions, passed in ATAG_REVISION by u-boot */
+#define GTA02v1_SYSTEM_REV 0x00000310
+#define GTA02v2_SYSTEM_REV 0x00000320
+#define GTA02v3_SYSTEM_REV 0x00000330
+#define GTA02v4_SYSTEM_REV 0x00000340
+#define GTA02v5_SYSTEM_REV 0x00000350
+/* since A7 is basically same as A6, we use A6 PCB ID */
+#define GTA02v6_SYSTEM_REV 0x00000360
+
+#define GTA02_GPIO_n3DL_GSM S3C2410_GPA(13) /* v1 + v2 + v3 only */
+
+#define GTA02_GPIO_PWR_LED1 S3C2410_GPB(0)
+#define GTA02_GPIO_PWR_LED2 S3C2410_GPB(1)
+#define GTA02_GPIO_AUX_LED S3C2410_GPB(2)
+#define GTA02_GPIO_VIBRATOR_ON S3C2410_GPB(3)
+#define GTA02_GPIO_MODEM_RST S3C2410_GPB(5)
+#define GTA02_GPIO_BT_EN S3C2410_GPB(6)
+#define GTA02_GPIO_MODEM_ON S3C2410_GPB(7)
+#define GTA02_GPIO_EXTINT8 S3C2410_GPB(8)
+#define GTA02_GPIO_USB_PULLUP S3C2410_GPB(9)
+
+#define GTA02_GPIO_PIO5 S3C2410_GPC(5) /* v3 + v4 only */
+
+#define GTA02v3_GPIO_nG1_CS S3C2410_GPD(12) /* v3 + v4 only */
+#define GTA02v3_GPIO_nG2_CS S3C2410_GPD(13) /* v3 + v4 only */
+#define GTA02v5_GPIO_HDQ S3C2410_GPD(14) /* v5 + */
+
+#define GTA02_GPIO_nG1_INT S3C2410_GPF(0)
+#define GTA02_GPIO_IO1 S3C2410_GPF(1)
+#define GTA02_GPIO_PIO_2 S3C2410_GPF(2) /* v2 + v3 + v4 only */
+#define GTA02_GPIO_JACK_INSERT S3C2410_GPF(4)
+#define GTA02_GPIO_WLAN_GPIO1 S3C2410_GPF(5) /* v2 + v3 + v4 only */
+#define GTA02_GPIO_AUX_KEY S3C2410_GPF(6)
+#define GTA02_GPIO_HOLD_KEY S3C2410_GPF(7)
+
+#define GTA02_GPIO_3D_IRQ S3C2410_GPG(4)
+#define GTA02v2_GPIO_nG2_INT S3C2410_GPG(8) /* v2 + v3 + v4 only */
+#define GTA02v3_GPIO_nUSB_OC S3C2410_GPG(9) /* v3 + v4 only */
+#define GTA02v3_GPIO_nUSB_FLT S3C2410_GPG(10) /* v3 + v4 only */
+#define GTA02v3_GPIO_nGSM_OC S3C2410_GPG(11) /* v3 + v4 only */
+
+#define GTA02_GPIO_AMP_SHUT S3C2440_GPJ1 /* v2 + v3 + v4 only */
+#define GTA02v1_GPIO_WLAN_GPIO10 S3C2440_GPJ2
+#define GTA02_GPIO_HP_IN S3C2440_GPJ2 /* v2 + v3 + v4 only */
+#define GTA02_GPIO_INT0 S3C2440_GPJ3 /* v2 + v3 + v4 only */
+#define GTA02_GPIO_nGSM_EN S3C2440_GPJ4
+#define GTA02_GPIO_3D_RESET S3C2440_GPJ5
+#define GTA02_GPIO_nDL_GSM S3C2440_GPJ6 /* v4 + v5 only */
+#define GTA02_GPIO_WLAN_GPIO0 S3C2440_GPJ7
+#define GTA02v1_GPIO_BAT_ID S3C2440_GPJ8
+#define GTA02_GPIO_KEEPACT S3C2440_GPJ8
+#define GTA02v1_GPIO_HP_IN S3C2440_GPJ10
+#define GTA02_CHIP_PWD S3C2440_GPJ11 /* v2 + v3 + v4 only */
+#define GTA02_GPIO_nWLAN_RESET S3C2440_GPJ12 /* v2 + v3 + v4 only */
+
+#define GTA02_IRQ_GSENSOR_1 IRQ_EINT0
+#define GTA02_IRQ_MODEM IRQ_EINT1
+#define GTA02_IRQ_PIO_2 IRQ_EINT2 /* v2 + v3 + v4 only */
+#define GTA02_IRQ_nJACK_INSERT IRQ_EINT4
+#define GTA02_IRQ_WLAN_GPIO1 IRQ_EINT5
+#define GTA02_IRQ_AUX IRQ_EINT6
+#define GTA02_IRQ_nHOLD IRQ_EINT7
+#define GTA02_IRQ_PCF50633 IRQ_EINT9
+#define GTA02_IRQ_3D IRQ_EINT12
+#define GTA02_IRQ_GSENSOR_2 IRQ_EINT16 /* v2 + v3 + v4 only */
+#define GTA02v3_IRQ_nUSB_OC IRQ_EINT17 /* v3 + v4 only */
+#define GTA02v3_IRQ_nUSB_FLT IRQ_EINT18 /* v3 + v4 only */
+#define GTA02v3_IRQ_nGSM_OC IRQ_EINT19 /* v3 + v4 only */
+
+/* returns 00 000 on GTA02 A5 and earlier, A6 returns 01 001 */
+#define GTA02_PCB_ID1_0 S3C2410_GPC(13)
+#define GTA02_PCB_ID1_1 S3C2410_GPC(15)
+#define GTA02_PCB_ID1_2 S3C2410_GPD(0)
+#define GTA02_PCB_ID2_0 S3C2410_GPD(3)
+#define GTA02_PCB_ID2_1 S3C2410_GPD(4)
+
+int gta02_get_pcb_revision(void);
+
+#endif /* _GTA02_H */
--- /dev/null
+/*
+ * linux/arch/arm/mach-s3c2442/mach-gta02.c
+ *
+ * S3C2442 Machine Support for Openmoko GTA02 / FreeRunner.
+ *
+ * Copyright (C) 2006-2009 by Openmoko, Inc.
+ * Authors: Harald Welte <laforge@openmoko.org>
+ * Andy Green <andy@openmoko.org>
+ * Werner Almesberger <werner@openmoko.org>
+ * All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/delay.h>
+#include <linux/timer.h>
+#include <linux/init.h>
+#include <linux/gpio.h>
+#include <linux/workqueue.h>
+#include <linux/platform_device.h>
+#include <linux/serial_core.h>
+#include <linux/spi/spi.h>
+
+#include <linux/mmc/host.h>
+
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/nand_ecc.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+#include <linux/io.h>
+
+#include <linux/i2c.h>
+#include <linux/backlight.h>
+#include <linux/regulator/machine.h>
+
+#include <linux/mfd/pcf50633/core.h>
+#include <linux/mfd/pcf50633/mbc.h>
+#include <linux/mfd/pcf50633/adc.h>
+#include <linux/mfd/pcf50633/gpio.h>
+#include <linux/mfd/pcf50633/pmic.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+
+#include <mach/regs-irq.h>
+#include <mach/regs-gpio.h>
+#include <mach/regs-gpioj.h>
+#include <mach/fb.h>
+
+#include <mach/spi.h>
+#include <mach/spi-gpio.h>
+#include <plat/usb-control.h>
+#include <mach/regs-mem.h>
+#include <mach/hardware.h>
+
+#include <mach/gta02.h>
+
+#include <plat/regs-serial.h>
+#include <plat/nand.h>
+#include <plat/devs.h>
+#include <plat/cpu.h>
+#include <plat/pm.h>
+#include <plat/udc.h>
+#include <plat/gpio-cfg.h>
+#include <plat/iic.h>
+
+static struct pcf50633 *gta02_pcf;
+
+/*
+ * This gets called every 1ms when we paniced.
+ */
+
+static long gta02_panic_blink(long count)
+{
+ long delay = 0;
+ static long last_blink;
+ static char led;
+
+ /* Fast blink: 200ms period. */
+ if (count - last_blink < 100)
+ return 0;
+
+ led ^= 1;
+ gpio_direction_output(GTA02_GPIO_AUX_LED, led);
+
+ last_blink = count;
+
+ return delay;
+}
+
+
+static struct map_desc gta02_iodesc[] __initdata = {
+ {
+ .virtual = 0xe0000000,
+ .pfn = __phys_to_pfn(S3C2410_CS3 + 0x01000000),
+ .length = SZ_1M,
+ .type = MT_DEVICE
+ },
+};
+
+#define UCON (S3C2410_UCON_DEFAULT | S3C2443_UCON_RXERR_IRQEN)
+#define ULCON (S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB)
+#define UFCON (S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE)
+
+static struct s3c2410_uartcfg gta02_uartcfgs[] = {
+ [0] = {
+ .hwport = 0,
+ .flags = 0,
+ .ucon = UCON,
+ .ulcon = ULCON,
+ .ufcon = UFCON,
+ },
+ [1] = {
+ .hwport = 1,
+ .flags = 0,
+ .ucon = UCON,
+ .ulcon = ULCON,
+ .ufcon = UFCON,
+ },
+ [2] = {
+ .hwport = 2,
+ .flags = 0,
+ .ucon = UCON,
+ .ulcon = ULCON,
+ .ufcon = UFCON,
+ },
+};
+
+#ifdef CONFIG_CHARGER_PCF50633
+/*
+ * On GTA02 the 1A charger features a 48K resistor to 0V on the ID pin.
+ * We use this to recognize that we can pull 1A from the USB socket.
+ *
+ * These constants are the measured pcf50633 ADC levels with the 1A
+ * charger / 48K resistor, and with no pulldown resistor.
+ */
+
+#define ADC_NOM_CHG_DETECT_1A 6
+#define ADC_NOM_CHG_DETECT_USB 43
+
+static void
+gta02_configure_pmu_for_charger(struct pcf50633 *pcf, void *unused, int res)
+{
+ int ma;
+
+ /* Interpret charger type */
+ if (res < ((ADC_NOM_CHG_DETECT_USB + ADC_NOM_CHG_DETECT_1A) / 2)) {
+
+ /*
+ * Sanity - stop GPO driving out now that we have a 1A charger
+ * GPO controls USB Host power generation on GTA02
+ */
+ pcf50633_gpio_set(pcf, PCF50633_GPO, 0);
+
+ ma = 1000;
+ } else
+ ma = 100;
+
+ pcf50633_mbc_usb_curlim_set(pcf, ma);
+}
+
+static struct delayed_work gta02_charger_work;
+static int gta02_usb_vbus_draw;
+
+static void gta02_charger_worker(struct work_struct *work)
+{
+ if (gta02_usb_vbus_draw) {
+ pcf50633_mbc_usb_curlim_set(gta02_pcf, gta02_usb_vbus_draw);
+ return;
+ }
+
+#ifdef CONFIG_PCF50633_ADC
+ pcf50633_adc_async_read(gta02_pcf,
+ PCF50633_ADCC1_MUX_ADCIN1,
+ PCF50633_ADCC1_AVERAGE_16,
+ gta02_configure_pmu_for_charger,
+ NULL);
+#else
+ /*
+ * If the PCF50633 ADC is disabled we fallback to a
+ * 100mA limit for safety.
+ */
+ pcf50633_mbc_usb_curlim_set(pcf, 100);
+#endif
+}
+
+#define GTA02_CHARGER_CONFIGURE_TIMEOUT ((3000 * HZ) / 1000)
+
+static void gta02_pmu_event_callback(struct pcf50633 *pcf, int irq)
+{
+ if (irq == PCF50633_IRQ_USBINS) {
+ schedule_delayed_work(>a02_charger_work,
+ GTA02_CHARGER_CONFIGURE_TIMEOUT);
+
+ return;
+ }
+
+ if (irq == PCF50633_IRQ_USBREM) {
+ cancel_delayed_work_sync(>a02_charger_work);
+ gta02_usb_vbus_draw = 0;
+ }
+}
+
+static void gta02_udc_vbus_draw(unsigned int ma)
+{
+ if (!gta02_pcf)
+ return;
+
+ gta02_usb_vbus_draw = ma;
+
+ schedule_delayed_work(>a02_charger_work,
+ GTA02_CHARGER_CONFIGURE_TIMEOUT);
+}
+#else /* !CONFIG_CHARGER_PCF50633 */
+#define gta02_pmu_event_callback NULL
+#define gta02_udc_vbus_draw NULL
+#endif
+
+/*
+ * This is called when pc50633 is probed, unfortunately quite late in the
+ * day since it is an I2C bus device. Here we can belatedly define some
+ * platform devices with the advantage that we can mark the pcf50633 as the
+ * parent. This makes them get suspended and resumed with their parent
+ * the pcf50633 still around.
+ */
+
+static void gta02_pmu_attach_child_devices(struct pcf50633 *pcf);
+
+
+static char *gta02_batteries[] = {
+ "battery",
+};
+
+struct pcf50633_platform_data gta02_pcf_pdata = {
+ .resumers = {
+ [0] = PCF50633_INT1_USBINS |
+ PCF50633_INT1_USBREM |
+ PCF50633_INT1_ALARM,
+ [1] = PCF50633_INT2_ONKEYF,
+ [2] = PCF50633_INT3_ONKEY1S,
+ [3] = PCF50633_INT4_LOWSYS |
+ PCF50633_INT4_LOWBAT |
+ PCF50633_INT4_HIGHTMP,
+ },
+
+ .batteries = gta02_batteries,
+ .num_batteries = ARRAY_SIZE(gta02_batteries),
+ .reg_init_data = {
+ [PCF50633_REGULATOR_AUTO] = {
+ .constraints = {
+ .min_uV = 3300000,
+ .max_uV = 3300000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL,
+ .always_on = 1,
+ .apply_uV = 1,
+ .state_mem = {
+ .enabled = 1,
+ },
+ },
+ },
+ [PCF50633_REGULATOR_DOWN1] = {
+ .constraints = {
+ .min_uV = 1300000,
+ .max_uV = 1600000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL,
+ .always_on = 1,
+ .apply_uV = 1,
+ },
+ },
+ [PCF50633_REGULATOR_DOWN2] = {
+ .constraints = {
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL,
+ .apply_uV = 1,
+ .always_on = 1,
+ .state_mem = {
+ .enabled = 1,
+ },
+ },
+ },
+ [PCF50633_REGULATOR_HCLDO] = {
+ .constraints = {
+ .min_uV = 2000000,
+ .max_uV = 3300000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
+ .always_on = 1,
+ },
+ },
+ [PCF50633_REGULATOR_LDO1] = {
+ .constraints = {
+ .min_uV = 3300000,
+ .max_uV = 3300000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL,
+ .apply_uV = 1,
+ .state_mem = {
+ .enabled = 0,
+ },
+ },
+ },
+ [PCF50633_REGULATOR_LDO2] = {
+ .constraints = {
+ .min_uV = 3300000,
+ .max_uV = 3300000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL,
+ .apply_uV = 1,
+ },
+ },
+ [PCF50633_REGULATOR_LDO3] = {
+ .constraints = {
+ .min_uV = 3000000,
+ .max_uV = 3000000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL,
+ .apply_uV = 1,
+ },
+ },
+ [PCF50633_REGULATOR_LDO4] = {
+ .constraints = {
+ .min_uV = 3200000,
+ .max_uV = 3200000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL,
+ .apply_uV = 1,
+ },
+ },
+ [PCF50633_REGULATOR_LDO5] = {
+ .constraints = {
+ .min_uV = 3000000,
+ .max_uV = 3000000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL,
+ .apply_uV = 1,
+ .state_mem = {
+ .enabled = 1,
+ },
+ },
+ },
+ [PCF50633_REGULATOR_LDO6] = {
+ .constraints = {
+ .min_uV = 3000000,
+ .max_uV = 3000000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL,
+ },
+ },
+ [PCF50633_REGULATOR_MEMLDO] = {
+ .constraints = {
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL,
+ .state_mem = {
+ .enabled = 1,
+ },
+ },
+ },
+
+ },
+ .probe_done = gta02_pmu_attach_child_devices,
+ .mbc_event_callback = gta02_pmu_event_callback,
+};
+
+
+/* NOR Flash. */
+
+#define GTA02_FLASH_BASE 0x18000000 /* GCS3 */
+#define GTA02_FLASH_SIZE 0x200000 /* 2MBytes */
+
+static struct physmap_flash_data gta02_nor_flash_data = {
+ .width = 2,
+};
+
+static struct resource gta02_nor_flash_resource = {
+ .start = GTA02_FLASH_BASE,
+ .end = GTA02_FLASH_BASE + GTA02_FLASH_SIZE - 1,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device gta02_nor_flash = {
+ .name = "physmap-flash",
+ .id = 0,
+ .dev = {
+ .platform_data = >a02_nor_flash_data,
+ },
+ .resource = >a02_nor_flash_resource,
+ .num_resources = 1,
+};
+
+
+struct platform_device s3c24xx_pwm_device = {
+ .name = "s3c24xx_pwm",
+ .num_resources = 0,
+};
+
+static struct i2c_board_info gta02_i2c_devs[] __initdata = {
+ {
+ I2C_BOARD_INFO("pcf50633", 0x73),
+ .irq = GTA02_IRQ_PCF50633,
+ .platform_data = >a02_pcf_pdata,
+ },
+ {
+ I2C_BOARD_INFO("wm8753", 0x1a),
+ },
+};
+
+static struct s3c2410_nand_set gta02_nand_sets[] = {
+ [0] = {
+ /*
+ * This name is also hard-coded in the boot loaders, so
+ * changing it would would require all users to upgrade
+ * their boot loaders, some of which are stored in a NOR
+ * that is considered to be immutable.
+ */
+ .name = "neo1973-nand",
+ .nr_chips = 1,
+ .use_bbt = 1,
+ .force_soft_ecc = 1,
+ },
+};
+
+/*
+ * Choose a set of timings derived from S3C@2442B MCP54
+ * data sheet (K5D2G13ACM-D075 MCP Memory).
+ */
+
+static struct s3c2410_platform_nand gta02_nand_info = {
+ .tacls = 0,
+ .twrph0 = 25,
+ .twrph1 = 15,
+ .nr_sets = ARRAY_SIZE(gta02_nand_sets),
+ .sets = gta02_nand_sets,
+};
+
+
+static void gta02_udc_command(enum s3c2410_udc_cmd_e cmd)
+{
+ switch (cmd) {
+ case S3C2410_UDC_P_ENABLE:
+ pr_debug("%s S3C2410_UDC_P_ENABLE\n", __func__);
+ gpio_direction_output(GTA02_GPIO_USB_PULLUP, 1);
+ break;
+ case S3C2410_UDC_P_DISABLE:
+ pr_debug("%s S3C2410_UDC_P_DISABLE\n", __func__);
+ gpio_direction_output(GTA02_GPIO_USB_PULLUP, 0);
+ break;
+ case S3C2410_UDC_P_RESET:
+ pr_debug("%s S3C2410_UDC_P_RESET\n", __func__);
+ /* FIXME: Do something here. */
+ }
+}
+
+/* Get PMU to set USB current limit accordingly. */
+static struct s3c2410_udc_mach_info gta02_udc_cfg = {
+ .vbus_draw = gta02_udc_vbus_draw,
+ .udc_command = gta02_udc_command,
+
+};
+
+
+
+static void gta02_bl_set_intensity(int intensity)
+{
+ struct pcf50633 *pcf = gta02_pcf;
+ int old_intensity = pcf50633_reg_read(pcf, PCF50633_REG_LEDOUT);
+
+ /* We map 8-bit intensity to 6-bit intensity in hardware. */
+ intensity >>= 2;
+
+ /*
+ * This can happen during, eg, print of panic on blanked console,
+ * but we can't service i2c without interrupts active, so abort.
+ */
+ if (in_atomic()) {
+ printk(KERN_ERR "gta02_bl_set_intensity called while atomic\n");
+ return;
+ }
+
+ old_intensity = pcf50633_reg_read(pcf, PCF50633_REG_LEDOUT);
+ if (intensity == old_intensity)
+ return;
+
+ /* We can't do this anywhere else. */
+ pcf50633_reg_write(pcf, PCF50633_REG_LEDDIM, 5);
+
+ if (!(pcf50633_reg_read(pcf, PCF50633_REG_LEDENA) & 3))
+ old_intensity = 0;
+
+ /*
+ * The PCF50633 cannot handle LEDOUT = 0 (datasheet p60)
+ * if seen, you have to re-enable the LED unit.
+ */
+ if (!intensity || !old_intensity)
+ pcf50633_reg_write(pcf, PCF50633_REG_LEDENA, 0);
+
+ /* Illegal to set LEDOUT to 0. */
+ if (!intensity)
+ pcf50633_reg_set_bit_mask(pcf, PCF50633_REG_LEDOUT, 0x3f, 2);
+ else
+ pcf50633_reg_set_bit_mask(pcf, PCF50633_REG_LEDOUT, 0x3f,
+ intensity);
+
+ if (intensity)
+ pcf50633_reg_write(pcf, PCF50633_REG_LEDENA, 2);
+
+}
+
+static struct generic_bl_info gta02_bl_info = {
+ .name = "gta02-bl",
+ .max_intensity = 0xff,
+ .default_intensity = 0xff,
+ .set_bl_intensity = gta02_bl_set_intensity,
+};
+
+static struct platform_device gta02_bl_dev = {
+ .name = "generic-bl",
+ .id = 1,
+ .dev = {
+ .platform_data = >a02_bl_info,
+ },
+};
+
+
+
+/* USB */
+static struct s3c2410_hcd_info gta02_usb_info = {
+ .port[0] = {
+ .flags = S3C_HCDFLG_USED,
+ },
+ .port[1] = {
+ .flags = 0,
+ },
+};
+
+
+static void __init gta02_map_io(void)
+{
+ s3c24xx_init_io(gta02_iodesc, ARRAY_SIZE(gta02_iodesc));
+ s3c24xx_init_clocks(12000000);
+ s3c24xx_init_uarts(gta02_uartcfgs, ARRAY_SIZE(gta02_uartcfgs));
+}
+
+
+/* These are the guys that don't need to be children of PMU. */
+
+static struct platform_device *gta02_devices[] __initdata = {
+ &s3c_device_usb,
+ &s3c_device_wdt,
+ &s3c_device_sdi,
+ &s3c_device_usbgadget,
+ &s3c_device_nand,
+ >a02_nor_flash,
+ &s3c24xx_pwm_device,
+ &s3c_device_iis,
+ &s3c_device_i2c0,
+};
+
+/* These guys DO need to be children of PMU. */
+
+static struct platform_device *gta02_devices_pmu_children[] = {
+ >a02_bl_dev,
+};
+
+
+/*
+ * This is called when pc50633 is probed, quite late in the day since it is an
+ * I2C bus device. Here we can define platform devices with the advantage that
+ * we can mark the pcf50633 as the parent. This makes them get suspended and
+ * resumed with their parent the pcf50633 still around. All devices whose
+ * operation depends on something from pcf50633 must have this relationship
+ * made explicit like this, or suspend and resume will become an unreliable
+ * hellworld.
+ */
+
+static void gta02_pmu_attach_child_devices(struct pcf50633 *pcf)
+{
+ int n;
+
+ /* Grab a copy of the now probed PMU pointer. */
+ gta02_pcf = pcf;
+
+ for (n = 0; n < ARRAY_SIZE(gta02_devices_pmu_children); n++)
+ gta02_devices_pmu_children[n]->dev.parent = pcf->dev;
+
+ platform_add_devices(gta02_devices_pmu_children,
+ ARRAY_SIZE(gta02_devices_pmu_children));
+}
+
+static void gta02_poweroff(void)
+{
+ pcf50633_reg_set_bit_mask(gta02_pcf, PCF50633_REG_OOCSHDWN, 1, 1);
+}
+
+static void __init gta02_machine_init(void)
+{
+ /* Set the panic callback to make AUX LED blink at ~5Hz. */
+ panic_blink = gta02_panic_blink;
+
+ s3c_pm_init();
+
+#ifdef CONFIG_CHARGER_PCF50633
+ INIT_DELAYED_WORK(>a02_charger_work, gta02_charger_worker);
+#endif
+
+ s3c_device_usb.dev.platform_data = >a02_usb_info;
+ s3c_device_nand.dev.platform_data = >a02_nand_info;
+
+ s3c24xx_udc_set_platdata(>a02_udc_cfg);
+ s3c_i2c0_set_platdata(NULL);
+
+ i2c_register_board_info(0, gta02_i2c_devs, ARRAY_SIZE(gta02_i2c_devs));
+
+ platform_add_devices(gta02_devices, ARRAY_SIZE(gta02_devices));
+ pm_power_off = gta02_poweroff;
+}
+
+
+MACHINE_START(NEO1973_GTA02, "GTA02")
+ /* Maintainer: Nelson Castillo <arhuaco@freaks-unidos.net> */
+ .phys_io = S3C2410_PA_UART,
+ .io_pg_offst = (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc,
+ .boot_params = S3C2410_SDRAM_PA + 0x100,
+ .map_io = gta02_map_io,
+ .init_irq = s3c24xx_init_irq,
+ .init_machine = gta02_machine_init,
+ .timer = &s3c24xx_timer,
+MACHINE_END
#define SHIFT_ASR 0x40
#define SHIFT_RORRRX 0x60
+#define BAD_INSTR 0xdeadc0de
+
+/* Thumb-2 32 bit format per ARMv7 DDI0406A A6.3, either f800h,e800h,f800h */
+#define IS_T32(hi16) \
+ (((hi16) & 0xe000) == 0xe000 && ((hi16) & 0x1800))
+
static unsigned long ai_user;
static unsigned long ai_sys;
static unsigned long ai_skipped;
struct pt_regs *regs)
{
unsigned int rd = RD_BITS(instr);
-
- if (((rd & 1) == 1) || (rd == 14))
+ unsigned int rd2;
+ int load;
+
+ if ((instr & 0xfe000000) == 0xe8000000) {
+ /* ARMv7 Thumb-2 32-bit LDRD/STRD */
+ rd2 = (instr >> 8) & 0xf;
+ load = !!(LDST_L_BIT(instr));
+ } else if (((rd & 1) == 1) || (rd == 14))
goto bad;
+ else {
+ load = ((instr & 0xf0) == 0xd0);
+ rd2 = rd + 1;
+ }
ai_dword += 1;
if (user_mode(regs))
goto user;
- if ((instr & 0xf0) == 0xd0) {
+ if (load) {
unsigned long val;
get32_unaligned_check(val, addr);
regs->uregs[rd] = val;
get32_unaligned_check(val, addr + 4);
- regs->uregs[rd + 1] = val;
+ regs->uregs[rd2] = val;
} else {
put32_unaligned_check(regs->uregs[rd], addr);
- put32_unaligned_check(regs->uregs[rd + 1], addr + 4);
+ put32_unaligned_check(regs->uregs[rd2], addr + 4);
}
return TYPE_LDST;
user:
- if ((instr & 0xf0) == 0xd0) {
+ if (load) {
unsigned long val;
get32t_unaligned_check(val, addr);
regs->uregs[rd] = val;
get32t_unaligned_check(val, addr + 4);
- regs->uregs[rd + 1] = val;
+ regs->uregs[rd2] = val;
} else {
put32t_unaligned_check(regs->uregs[rd], addr);
- put32t_unaligned_check(regs->uregs[rd + 1], addr + 4);
+ put32t_unaligned_check(regs->uregs[rd2], addr + 4);
}
return TYPE_LDST;
/* Else fall through for illegal instruction case */
default:
- return 0xdeadc0de;
+ return BAD_INSTR;
+ }
+}
+
+/*
+ * Convert Thumb-2 32 bit LDM, STM, LDRD, STRD to equivalent instruction
+ * handlable by ARM alignment handler, also find the corresponding handler,
+ * so that we can reuse ARM userland alignment fault fixups for Thumb.
+ *
+ * @pinstr: original Thumb-2 instruction; returns new handlable instruction
+ * @regs: register context.
+ * @poffset: return offset from faulted addr for later writeback
+ *
+ * NOTES:
+ * 1. Comments below refer to ARMv7 DDI0406A Thumb Instruction sections.
+ * 2. Register name Rt from ARMv7 is same as Rd from ARMv6 (Rd is Rt)
+ */
+static void *
+do_alignment_t32_to_handler(unsigned long *pinstr, struct pt_regs *regs,
+ union offset_union *poffset)
+{
+ unsigned long instr = *pinstr;
+ u16 tinst1 = (instr >> 16) & 0xffff;
+ u16 tinst2 = instr & 0xffff;
+ poffset->un = 0;
+
+ switch (tinst1 & 0xffe0) {
+ /* A6.3.5 Load/Store multiple */
+ case 0xe880: /* STM/STMIA/STMEA,LDM/LDMIA, PUSH/POP T2 */
+ case 0xe8a0: /* ...above writeback version */
+ case 0xe900: /* STMDB/STMFD, LDMDB/LDMEA */
+ case 0xe920: /* ...above writeback version */
+ /* no need offset decision since handler calculates it */
+ return do_alignment_ldmstm;
+
+ case 0xf840: /* POP/PUSH T3 (single register) */
+ if (RN_BITS(instr) == 13 && (tinst2 & 0x09ff) == 0x0904) {
+ u32 L = !!(LDST_L_BIT(instr));
+ const u32 subset[2] = {
+ 0xe92d0000, /* STMDB sp!,{registers} */
+ 0xe8bd0000, /* LDMIA sp!,{registers} */
+ };
+ *pinstr = subset[L] | (1<<RD_BITS(instr));
+ return do_alignment_ldmstm;
+ }
+ /* Else fall through for illegal instruction case */
+ break;
+
+ /* A6.3.6 Load/store double, STRD/LDRD(immed, lit, reg) */
+ case 0xe860:
+ case 0xe960:
+ case 0xe8e0:
+ case 0xe9e0:
+ poffset->un = (tinst2 & 0xff) << 2;
+ case 0xe940:
+ case 0xe9c0:
+ return do_alignment_ldrdstrd;
+
+ /*
+ * No need to handle load/store instructions up to word size
+ * since ARMv6 and later CPUs can perform unaligned accesses.
+ */
+ default:
+ break;
}
+ return NULL;
}
static int
mm_segment_t fs;
unsigned int fault;
u16 tinstr = 0;
+ int isize = 4;
+ int thumb2_32b = 0;
instrptr = instruction_pointer(regs);
set_fs(KERNEL_DS);
if (thumb_mode(regs)) {
fault = __get_user(tinstr, (u16 *)(instrptr & ~1));
- if (!(fault))
- instr = thumb2arm(tinstr);
+ if (!fault) {
+ if (cpu_architecture() >= CPU_ARCH_ARMv7 &&
+ IS_T32(tinstr)) {
+ /* Thumb-2 32-bit */
+ u16 tinst2 = 0;
+ fault = __get_user(tinst2, (u16 *)(instrptr+2));
+ instr = (tinstr << 16) | tinst2;
+ thumb2_32b = 1;
+ } else {
+ isize = 2;
+ instr = thumb2arm(tinstr);
+ }
+ }
} else
fault = __get_user(instr, (u32 *)instrptr);
set_fs(fs);
fixup:
- regs->ARM_pc += thumb_mode(regs) ? 2 : 4;
+ regs->ARM_pc += isize;
switch (CODING_BITS(instr)) {
case 0x00000000: /* 3.13.4 load/store instruction extensions */
handler = do_alignment_ldrstr;
break;
- case 0x08000000: /* ldm or stm */
- handler = do_alignment_ldmstm;
+ case 0x08000000: /* ldm or stm, or thumb-2 32bit instruction */
+ if (thumb2_32b)
+ handler = do_alignment_t32_to_handler(&instr, regs, &offset);
+ else
+ handler = do_alignment_ldmstm;
break;
default:
goto bad;
}
+ if (!handler)
+ goto bad;
type = handler(addr, instr, regs);
- if (type == TYPE_ERROR || type == TYPE_FAULT)
+ if (type == TYPE_ERROR || type == TYPE_FAULT) {
+ regs->ARM_pc -= isize;
goto bad_or_fault;
+ }
if (type == TYPE_LDST)
do_alignment_finish_ldst(addr, instr, regs, offset);
bad_or_fault:
if (type == TYPE_ERROR)
goto bad;
- regs->ARM_pc -= thumb_mode(regs) ? 2 : 4;
/*
* We got a fault - fix it up, or die.
*/
*/
printk(KERN_ERR "Alignment trap: not handling instruction "
"%0*lx at [<%08lx>]\n",
- thumb_mode(regs) ? 4 : 8,
- thumb_mode(regs) ? tinstr : instr, instrptr);
+ isize << 1,
+ isize == 2 ? tinstr : instr, instrptr);
ai_skipped += 1;
return 1;
printk("Alignment trap: %s (%d) PC=0x%08lx Instr=0x%0*lx "
"Address=0x%08lx FSR 0x%03x\n", current->comm,
task_pid_nr(current), instrptr,
- thumb_mode(regs) ? 4 : 8,
- thumb_mode(regs) ? tinstr : instr,
+ isize << 1,
+ isize == 2 ? tinstr : instr,
addr, fsr);
if (ai_usermode & UM_FIXUP)
BOOTMEM_EXCLUSIVE);
}
+ if (machine_is_treo680()) {
+ reserve_bootmem_node(pgdat, 0xa0000000, 0x1000,
+ BOOTMEM_EXCLUSIVE);
+ reserve_bootmem_node(pgdat, 0xa2000000, 0x1000,
+ BOOTMEM_EXCLUSIVE);
+ }
+
if (machine_is_palmt5())
reserve_bootmem_node(pgdat, 0xa0200000, 0x1000,
BOOTMEM_EXCLUSIVE);
extern u32 omap3_configure_core_dpll(u32 sdrc_rfr_ctrl,
u32 sdrc_actim_ctrla,
u32 sdrc_actim_ctrlb, u32 m2,
- u32 unlock_dll);
+ u32 unlock_dll, u32 f, u32 sdrc_mr,
+ u32 inc);
/* Do not use these */
extern void omap1_sram_reprogram_clock(u32 ckctl, u32 dpllctl);
extern u32 omap3_sram_configure_core_dpll(u32 sdrc_rfr_ctrl,
u32 sdrc_actim_ctrla,
u32 sdrc_actim_ctrlb, u32 m2,
- u32 unlock_dll);
+ u32 unlock_dll, u32 f, u32 sdrc_mr,
+ u32 inc);
extern unsigned long omap3_sram_configure_core_dpll_sz;
#endif
static u32 (*_omap3_sram_configure_core_dpll)(u32 sdrc_rfr_ctrl,
u32 sdrc_actim_ctrla,
u32 sdrc_actim_ctrlb,
- u32 m2, u32 unlock_dll);
+ u32 m2, u32 unlock_dll,
+ u32 f, u32 sdrc_mr, u32 inc);
u32 omap3_configure_core_dpll(u32 sdrc_rfr_ctrl, u32 sdrc_actim_ctrla,
- u32 sdrc_actim_ctrlb, u32 m2, u32 unlock_dll)
+ u32 sdrc_actim_ctrlb, u32 m2, u32 unlock_dll,
+ u32 f, u32 sdrc_mr, u32 inc)
{
BUG_ON(!_omap3_sram_configure_core_dpll);
return _omap3_sram_configure_core_dpll(sdrc_rfr_ctrl,
sdrc_actim_ctrla,
sdrc_actim_ctrlb, m2,
- unlock_dll);
+ unlock_dll, f, sdrc_mr, inc);
}
/* REVISIT: Should this be same as omap34xx_sram_init() after off-idle? */
obj-$(CONFIG_S3C_DEV_HSMMC1) += dev-hsmmc1.o
obj-y += dev-i2c0.o
obj-$(CONFIG_S3C_DEV_I2C1) += dev-i2c1.o
+obj-$(CONFIG_SND_S3C24XX_SOC) += dev-audio.o
obj-$(CONFIG_S3C_DEV_FB) += dev-fb.o
obj-$(CONFIG_S3C_DEV_USB_HOST) += dev-usb.o
obj-$(CONFIG_S3C_DEV_USB_HSOTG) += dev-usb-hsotg.o
--- /dev/null
+/* linux/arch/arm/plat-s3c/dev-audio.c
+ *
+ * Copyright 2009 Wolfson Microelectronics
+ * Mark Brown <broonie@opensource.wolfsonmicro.com>
+ *
+
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/string.h>
+#include <linux/platform_device.h>
+
+#include <mach/irqs.h>
+#include <mach/map.h>
+
+#include <plat/devs.h>
+
+
+static struct resource s3c64xx_iis0_resource[] = {
+ [0] = {
+ .start = S3C64XX_PA_IIS0,
+ .end = S3C64XX_PA_IIS0 + 0x100 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+struct platform_device s3c64xx_device_iis0 = {
+ .name = "s3c64xx-iis",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(s3c64xx_iis0_resource),
+ .resource = s3c64xx_iis0_resource,
+};
+EXPORT_SYMBOL(s3c64xx_device_iis0);
+
+static struct resource s3c64xx_iis1_resource[] = {
+ [0] = {
+ .start = S3C64XX_PA_IIS1,
+ .end = S3C64XX_PA_IIS1 + 0x100 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+struct platform_device s3c64xx_device_iis1 = {
+ .name = "s3c64xx-iis",
+ .id = 1,
+ .num_resources = ARRAY_SIZE(s3c64xx_iis1_resource),
+ .resource = s3c64xx_iis1_resource,
+};
+EXPORT_SYMBOL(s3c64xx_device_iis1);
+
+static struct resource s3c64xx_iisv4_resource[] = {
+ [0] = {
+ .start = S3C64XX_PA_IISV4,
+ .end = S3C64XX_PA_IISV4 + 0x100 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+struct platform_device s3c64xx_device_iisv4 = {
+ .name = "s3c64xx-iis-v4",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(s3c64xx_iisv4_resource),
+ .resource = s3c64xx_iisv4_resource,
+};
+EXPORT_SYMBOL(s3c64xx_device_iisv4);
unsigned int shift = (off & 7) * 4;
u32 con;
- if (off < 8 && chip->chip.ngpio >= 8)
+ if (off < 8 && chip->chip.ngpio > 8)
reg -= 4;
if (s3c_gpio_is_cfg_special(cfg)) {
extern struct platform_device s3c_device_timer[];
+extern struct platform_device s3c64xx_device_iis0;
+extern struct platform_device s3c64xx_device_iis1;
+extern struct platform_device s3c64xx_device_iisv4;
+
extern struct platform_device s3c_device_fb;
extern struct platform_device s3c_device_usb;
extern struct platform_device s3c_device_lcd;
extern struct platform_device s3c_device_wdt;
extern struct platform_device s3c_device_i2c0;
extern struct platform_device s3c_device_i2c1;
-extern struct platform_device s3c_device_iis;
extern struct platform_device s3c_device_rtc;
extern struct platform_device s3c_device_adc;
extern struct platform_device s3c_device_sdi;
obj-$(CONFIG_CPU_S3C6400_INIT) += s3c6400-init.o
obj-$(CONFIG_CPU_S3C6400_CLOCK) += s3c6400-clock.o
+obj-$(CONFIG_CPU_FREQ_S3C64XX) += cpufreq.o
# PM support
.id = -1,
.parent = &clk_h,
.enable = s3c64xx_hclk_ctrl,
- .ctrlbit = S3C_CLKCON_SCLK_UHOST,
+ .ctrlbit = S3C_CLKCON_HCLK_UHOST,
}, {
.name = "hsmmc",
.id = 0,
--- /dev/null
+/* linux/arch/arm/plat-s3c64xx/cpufreq.c
+ *
+ * Copyright 2009 Wolfson Microelectronics plc
+ *
+ * S3C64xx CPUfreq Support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/cpufreq.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/regulator/consumer.h>
+
+static struct clk *armclk;
+static struct regulator *vddarm;
+
+#ifdef CONFIG_CPU_S3C6410
+struct s3c64xx_dvfs {
+ unsigned int vddarm_min;
+ unsigned int vddarm_max;
+};
+
+static struct s3c64xx_dvfs s3c64xx_dvfs_table[] = {
+ [0] = { 1000000, 1000000 },
+ [1] = { 1000000, 1050000 },
+ [2] = { 1050000, 1100000 },
+ [3] = { 1050000, 1150000 },
+ [4] = { 1250000, 1350000 },
+};
+
+static struct cpufreq_frequency_table s3c64xx_freq_table[] = {
+ { 0, 66000 },
+ { 0, 133000 },
+ { 1, 222000 },
+ { 1, 266000 },
+ { 2, 333000 },
+ { 2, 400000 },
+ { 3, 532000 },
+ { 3, 533000 },
+ { 4, 667000 },
+ { 0, CPUFREQ_TABLE_END },
+};
+#endif
+
+static int s3c64xx_cpufreq_verify_speed(struct cpufreq_policy *policy)
+{
+ if (policy->cpu != 0)
+ return -EINVAL;
+
+ return cpufreq_frequency_table_verify(policy, s3c64xx_freq_table);
+}
+
+static unsigned int s3c64xx_cpufreq_get_speed(unsigned int cpu)
+{
+ if (cpu != 0)
+ return 0;
+
+ return clk_get_rate(armclk) / 1000;
+}
+
+static int s3c64xx_cpufreq_set_target(struct cpufreq_policy *policy,
+ unsigned int target_freq,
+ unsigned int relation)
+{
+ int ret;
+ unsigned int i;
+ struct cpufreq_freqs freqs;
+ struct s3c64xx_dvfs *dvfs;
+
+ ret = cpufreq_frequency_table_target(policy, s3c64xx_freq_table,
+ target_freq, relation, &i);
+ if (ret != 0)
+ return ret;
+
+ freqs.cpu = 0;
+ freqs.old = clk_get_rate(armclk) / 1000;
+ freqs.new = s3c64xx_freq_table[i].frequency;
+ freqs.flags = 0;
+ dvfs = &s3c64xx_dvfs_table[s3c64xx_freq_table[i].index];
+
+ if (freqs.old == freqs.new)
+ return 0;
+
+ pr_debug("cpufreq: Transition %d-%dkHz\n", freqs.old, freqs.new);
+
+ cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE);
+
+#ifdef CONFIG_REGULATOR
+ if (vddarm && freqs.new > freqs.old) {
+ ret = regulator_set_voltage(vddarm,
+ dvfs->vddarm_min,
+ dvfs->vddarm_max);
+ if (ret != 0) {
+ pr_err("cpufreq: Failed to set VDDARM for %dkHz: %d\n",
+ freqs.new, ret);
+ goto err;
+ }
+ }
+#endif
+
+ ret = clk_set_rate(armclk, freqs.new * 1000);
+ if (ret < 0) {
+ pr_err("cpufreq: Failed to set rate %dkHz: %d\n",
+ freqs.new, ret);
+ goto err;
+ }
+
+#ifdef CONFIG_REGULATOR
+ if (vddarm && freqs.new < freqs.old) {
+ ret = regulator_set_voltage(vddarm,
+ dvfs->vddarm_min,
+ dvfs->vddarm_max);
+ if (ret != 0) {
+ pr_err("cpufreq: Failed to set VDDARM for %dkHz: %d\n",
+ freqs.new, ret);
+ goto err_clk;
+ }
+ }
+#endif
+
+ cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE);
+
+ pr_debug("cpufreq: Set actual frequency %lukHz\n",
+ clk_get_rate(armclk) / 1000);
+
+ return 0;
+
+err_clk:
+ if (clk_set_rate(armclk, freqs.old * 1000) < 0)
+ pr_err("Failed to restore original clock rate\n");
+err:
+ cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE);
+
+ return ret;
+}
+
+#ifdef CONFIG_REGULATOR
+static void __init s3c64xx_cpufreq_constrain_voltages(void)
+{
+ int count, v, i, found;
+ struct cpufreq_frequency_table *freq;
+ struct s3c64xx_dvfs *dvfs;
+
+ count = regulator_count_voltages(vddarm);
+ if (count < 0) {
+ pr_err("cpufreq: Unable to check supported voltages\n");
+ return;
+ }
+
+ freq = s3c64xx_freq_table;
+ while (freq->frequency != CPUFREQ_TABLE_END) {
+ if (freq->frequency == CPUFREQ_ENTRY_INVALID)
+ continue;
+
+ dvfs = &s3c64xx_dvfs_table[freq->index];
+ found = 0;
+
+ for (i = 0; i < count; i++) {
+ v = regulator_list_voltage(vddarm, i);
+ if (v >= dvfs->vddarm_min && v <= dvfs->vddarm_max)
+ found = 1;
+ }
+
+ if (!found) {
+ pr_debug("cpufreq: %dkHz unsupported by regulator\n",
+ freq->frequency);
+ freq->frequency = CPUFREQ_ENTRY_INVALID;
+ }
+
+ freq++;
+ }
+}
+#endif
+
+static int __init s3c64xx_cpufreq_driver_init(struct cpufreq_policy *policy)
+{
+ int ret;
+ struct cpufreq_frequency_table *freq;
+
+ if (policy->cpu != 0)
+ return -EINVAL;
+
+ if (s3c64xx_freq_table == NULL) {
+ pr_err("cpufreq: No frequency information for this CPU\n");
+ return -ENODEV;
+ }
+
+ armclk = clk_get(NULL, "armclk");
+ if (IS_ERR(armclk)) {
+ pr_err("cpufreq: Unable to obtain ARMCLK: %ld\n",
+ PTR_ERR(armclk));
+ return PTR_ERR(armclk);
+ }
+
+#ifdef CONFIG_REGULATOR
+ vddarm = regulator_get(NULL, "vddarm");
+ if (IS_ERR(vddarm)) {
+ ret = PTR_ERR(vddarm);
+ pr_err("cpufreq: Failed to obtain VDDARM: %d\n", ret);
+ pr_err("cpufreq: Only frequency scaling available\n");
+ vddarm = NULL;
+ } else {
+ s3c64xx_cpufreq_constrain_voltages();
+ }
+#endif
+
+ freq = s3c64xx_freq_table;
+ while (freq->frequency != CPUFREQ_TABLE_END) {
+ unsigned long r;
+
+ /* Check for frequencies we can generate */
+ r = clk_round_rate(armclk, freq->frequency * 1000);
+ r /= 1000;
+ if (r != freq->frequency)
+ freq->frequency = CPUFREQ_ENTRY_INVALID;
+
+ /* If we have no regulator then assume startup
+ * frequency is the maximum we can support. */
+ if (!vddarm && freq->frequency > s3c64xx_cpufreq_get_speed(0))
+ freq->frequency = CPUFREQ_ENTRY_INVALID;
+
+ freq++;
+ }
+
+ policy->cur = clk_get_rate(armclk) / 1000;
+
+ /* Pick a conservative guess in ns: we'll need ~1 I2C/SPI
+ * write plus clock reprogramming. */
+ policy->cpuinfo.transition_latency = 2 * 1000 * 1000;
+
+ ret = cpufreq_frequency_table_cpuinfo(policy, s3c64xx_freq_table);
+ if (ret != 0) {
+ pr_err("cpufreq: Failed to configure frequency table: %d\n",
+ ret);
+ regulator_put(vddarm);
+ clk_put(armclk);
+ }
+
+ return ret;
+}
+
+static struct cpufreq_driver s3c64xx_cpufreq_driver = {
+ .owner = THIS_MODULE,
+ .flags = 0,
+ .verify = s3c64xx_cpufreq_verify_speed,
+ .target = s3c64xx_cpufreq_set_target,
+ .get = s3c64xx_cpufreq_get_speed,
+ .init = s3c64xx_cpufreq_driver_init,
+ .name = "s3c",
+};
+
+static int __init s3c64xx_cpufreq_init(void)
+{
+ return cpufreq_register_driver(&s3c64xx_cpufreq_driver);
+}
+module_init(s3c64xx_cpufreq_init);
.get_pull = s3c_gpio_getpull_updown,
};
+int s3c64xx_gpio2int_gpn(struct gpio_chip *chip, unsigned pin)
+{
+ return IRQ_EINT(0) + pin;
+}
+
static struct s3c_gpio_chip gpio_2bit[] = {
{
.base = S3C64XX_GPF_BASE,
.base = S3C64XX_GPN(0),
.ngpio = S3C64XX_GPIO_N_NR,
.label = "GPN",
+ .to_irq = s3c64xx_gpio2int_gpn,
},
}, {
.base = S3C64XX_GPO_BASE,
#define S3C6400_CLKDIV2_SPI0_SHIFT (0)
/* HCLK GATE Registers */
-#define S3C_CLKCON_HCLK_BUS (1<<30)
-#define S3C_CLKCON_HCLK_SECUR (1<<29)
-#define S3C_CLKCON_HCLK_SDMA1 (1<<28)
-#define S3C_CLKCON_HCLK_SDMA2 (1<<27)
-#define S3C_CLKCON_HCLK_UHOST (1<<26)
+#define S3C_CLKCON_HCLK_3DSE (1<<31)
+#define S3C_CLKCON_HCLK_UHOST (1<<29)
+#define S3C_CLKCON_HCLK_SECUR (1<<28)
+#define S3C_CLKCON_HCLK_SDMA1 (1<<27)
+#define S3C_CLKCON_HCLK_SDMA0 (1<<26)
#define S3C_CLKCON_HCLK_IROM (1<<25)
#define S3C_CLKCON_HCLK_DDR1 (1<<24)
#define S3C_CLKCON_HCLK_DDR0 (1<<23)
#
# http://www.arm.linux.org.uk/developer/machines/?action=new
#
-# Last update: Fri May 29 10:14:20 2009
+# Last update: Sat Jun 20 22:28:39 2009
#
# machine_is_xxx CONFIG_xxxx MACH_TYPE_xxx number
#
h6044 MACH_H6044 H6044 1458
app MACH_APP APP 1459
tct_hammer MACH_TCT_HAMMER TCT_HAMMER 1460
-herald MACH_HERMES HERMES 1461
+herald MACH_HERALD HERALD 1461
artemis MACH_ARTEMIS ARTEMIS 1462
htctitan MACH_HTCTITAN HTCTITAN 1463
qranium MACH_QRANIUM QRANIUM 1464
omap3_wl_ff MACH_OMAP3_WL_FF OMAP3_WL_FF 2258
simcom MACH_SIMCOM SIMCOM 2259
mcwebio MACH_MCWEBIO MCWEBIO 2260
+omap3_phrazer MACH_OMAP3_PHRAZER OMAP3_PHRAZER 2261
+darwin MACH_DARWIN DARWIN 2262
+oratiscomu MACH_ORATISCOMU ORATISCOMU 2263
+rtsbc20 MACH_RTSBC20 RTSBC20 2264
+i780 MACH_I780 I780 2265
+gemini324 MACH_GEMINI324 GEMINI324 2266
+oratislan MACH_ORATISLAN ORATISLAN 2267
+oratisalog MACH_ORATISALOG ORATISALOG 2268
+oratismadi MACH_ORATISMADI ORATISMADI 2269
+oratisot16 MACH_ORATISOT16 ORATISOT16 2270
+oratisdesk MACH_ORATISDESK ORATISDESK 2271
+v2p_ca9 MACH_V2P_CA9 V2P_CA9 2272
+sintexo MACH_SINTEXO SINTEXO 2273
+cm3389 MACH_CM3389 CM3389 2274
+omap3_cio MACH_OMAP3_CIO OMAP3_CIO 2275
+sgh_i900 MACH_SGH_I900 SGH_I900 2276
+bst100 MACH_BST100 BST100 2277
+passion MACH_PASSION PASSION 2278
+indesign_at91sam MACH_INDESIGN_AT91SAM INDESIGN_AT91SAM 2279
+c4_badger MACH_C4_BADGER C4_BADGER 2280
+c4_viper MACH_C4_VIPER C4_VIPER 2281
+d2net MACH_D2NET D2NET 2282
+bigdisk MACH_BIGDISK BIGDISK 2283
+notalvision MACH_NOTALVISION NOTALVISION 2284
+omap3_kboc MACH_OMAP3_KBOC OMAP3_KBOC 2285
+cyclone MACH_CYCLONE CYCLONE 2286
+ninja MACH_NINJA NINJA 2287
+at91sam9g20ek_2mmc MACH_AT91SAM9G20EK_2MMC AT91SAM9G20EK_2MMC 2288
+bcmring MACH_BCMRING BCMRING 2289
+resol_dl2 MACH_RESOL_DL2 RESOL_DL2 2290
+ifosw MACH_IFOSW IFOSW 2291
+htcrhodium MACH_HTCRHODIUM HTCRHODIUM 2292
+htctopaz MACH_HTCTOPAZ HTCTOPAZ 2293
+matrix504 MACH_MATRIX504 MATRIX504 2294
+mrfsa MACH_MRFSA MRFSA 2295
.codec_dev = &soc_codec_dev_wm8731,
};
-/*
- * FIXME: This is a temporary bodge to avoid cross-tree merge issues.
- * New drivers should register the wm8731 I2C device in the machine
- * setup code (under arch/arm for ARM systems).
- */
-static int wm8731_i2c_register(void)
-{
- struct i2c_board_info info;
- struct i2c_adapter *adapter;
- struct i2c_client *client;
-
- memset(&info, 0, sizeof(struct i2c_board_info));
- info.addr = 0x1b;
- strlcpy(info.type, "wm8731", I2C_NAME_SIZE);
-
- adapter = i2c_get_adapter(0);
- if (!adapter) {
- printk(KERN_ERR "can't get i2c adapter 0\n");
- return -ENODEV;
- }
-
- client = i2c_new_device(adapter, &info);
- i2c_put_adapter(adapter);
- if (!client) {
- printk(KERN_ERR "can't add i2c device at 0x%x\n",
- (unsigned int)info.addr);
- return -ENODEV;
- }
-
- return 0;
-}
-
static struct platform_device *corgi_snd_device;
static int __init corgi_init(void)
machine_is_husky()))
return -ENODEV;
- ret = wm8731_i2c_register();
- if (ret != 0)
- return ret;
-
corgi_snd_device = platform_device_alloc("soc-audio", -1);
if (!corgi_snd_device)
return -ENOMEM;
.num_links = 1,
};
-/*
- * FIXME: This is a temporary bodge to avoid cross-tree merge issues.
- * New drivers should register the wm8731 I2C device in the machine
- * setup code (under arch/arm for ARM systems).
- */
-static int wm8731_i2c_register(void)
-{
- struct i2c_board_info info;
- struct i2c_adapter *adapter;
- struct i2c_client *client;
-
- memset(&info, 0, sizeof(struct i2c_board_info));
- info.addr = 0x1b;
- strlcpy(info.type, "wm8731", I2C_NAME_SIZE);
-
- adapter = i2c_get_adapter(0);
- if (!adapter) {
- printk(KERN_ERR "can't get i2c adapter 0\n");
- return -ENODEV;
- }
-
- client = i2c_new_device(adapter, &info);
- i2c_put_adapter(adapter);
- if (!client) {
- printk(KERN_ERR "can't add i2c device at 0x%x\n",
- (unsigned int)info.addr);
- return -ENODEV;
- }
-
- return 0;
-}
-
/* poodle audio subsystem */
static struct snd_soc_device poodle_snd_devdata = {
.card = &snd_soc_poodle,
if (!machine_is_poodle())
return -ENODEV;
- ret = wm8731_i2c_register();
- if (ret != 0)
- return ret;
-
locomo_gpio_set_dir(&poodle_locomo_device.dev,
POODLE_LOCOMO_GPIO_AMP_ON, 0);
/* should we mute HP at startup - burning power ?*/
projects / karo-tx-linux.git / commitdiff