- compatible: Should be "atmel,<chip>-aic"
- interrupt-controller: Identifies the node as an interrupt controller.
- interrupt-parent: For single AIC system, it is an empty property.
-- #interrupt-cells: The number of cells to define the interrupts. It sould be 2.
+- #interrupt-cells: The number of cells to define the interrupts. It sould be 3.
The first cell is the IRQ number (aka "Peripheral IDentifier" on datasheet).
The second cell is used to specify flags:
bits[3:0] trigger type and level flags:
8 = active low level-sensitive.
Valid combinations are 1, 2, 3, 4, 8.
Default flag for internal sources should be set to 4 (active high).
+ The third cell is used to specify the irq priority from 0 (lowest) to 7
+ (highest).
- reg: Should contain AIC registers location and length
+- atmel,external-irqs: u32 array of external irqs.
Examples:
/*
compatible = "atmel,at91rm9200-aic";
interrupt-controller;
interrupt-parent;
- #interrupt-cells = <2>;
+ #interrupt-cells = <3>;
reg = <0xfffff000 0x200>;
};
dma: dma-controller@ffffec00 {
compatible = "atmel,at91sam9g45-dma";
reg = <0xffffec00 0x200>;
- interrupts = <21 4>;
+ interrupts = <21 4 5>;
};
ranges;
aic: interrupt-controller@fffff000 {
- #interrupt-cells = <2>;
+ #interrupt-cells = <3>;
compatible = "atmel,at91rm9200-aic";
interrupt-controller;
reg = <0xfffff000 0x200>;
+ atmel,external-irqs = <29 30 31>;
};
ramc0: ramc@ffffea00 {
pit: timer@fffffd30 {
compatible = "atmel,at91sam9260-pit";
reg = <0xfffffd30 0xf>;
- interrupts = <1 4>;
+ interrupts = <1 4 7>;
};
tcb0: timer@fffa0000 {
compatible = "atmel,at91rm9200-tcb";
reg = <0xfffa0000 0x100>;
- interrupts = <17 4 18 4 19 4>;
+ interrupts = <17 4 0 18 4 0 19 4 0>;
};
tcb1: timer@fffdc000 {
compatible = "atmel,at91rm9200-tcb";
reg = <0xfffdc000 0x100>;
- interrupts = <26 4 27 4 28 4>;
+ interrupts = <26 4 0 27 4 0 28 4 0>;
};
pioA: gpio@fffff400 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff400 0x100>;
- interrupts = <2 4>;
+ interrupts = <2 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
pioB: gpio@fffff600 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff600 0x100>;
- interrupts = <3 4>;
+ interrupts = <3 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
pioC: gpio@fffff800 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff800 0x100>;
- interrupts = <4 4>;
+ interrupts = <4 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
dbgu: serial@fffff200 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffff200 0x200>;
- interrupts = <1 4>;
+ interrupts = <1 4 7>;
status = "disabled";
};
usart0: serial@fffb0000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffb0000 0x200>;
- interrupts = <6 4>;
+ interrupts = <6 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";
usart1: serial@fffb4000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffb4000 0x200>;
- interrupts = <7 4>;
+ interrupts = <7 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";
usart2: serial@fffb8000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffb8000 0x200>;
- interrupts = <8 4>;
+ interrupts = <8 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";
usart3: serial@fffd0000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffd0000 0x200>;
- interrupts = <23 4>;
+ interrupts = <23 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";
usart4: serial@fffd4000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffd4000 0x200>;
- interrupts = <24 4>;
+ interrupts = <24 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";
usart5: serial@fffd8000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffd8000 0x200>;
- interrupts = <25 4>;
+ interrupts = <25 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";
macb0: ethernet@fffc4000 {
compatible = "cdns,at32ap7000-macb", "cdns,macb";
reg = <0xfffc4000 0x100>;
- interrupts = <21 4>;
+ interrupts = <21 4 3>;
status = "disabled";
};
usb1: gadget@fffa4000 {
compatible = "atmel,at91rm9200-udc";
reg = <0xfffa4000 0x4000>;
- interrupts = <10 4>;
+ interrupts = <10 4 2>;
status = "disabled";
};
adc0: adc@fffe0000 {
compatible = "atmel,at91sam9260-adc";
reg = <0xfffe0000 0x100>;
- interrupts = <5 4>;
+ interrupts = <5 4 0>;
atmel,adc-use-external-triggers;
atmel,adc-channels-used = <0xf>;
atmel,adc-vref = <3300>;
usb0: ohci@00500000 {
compatible = "atmel,at91rm9200-ohci", "usb-ohci";
reg = <0x00500000 0x100000>;
- interrupts = <20 4>;
+ interrupts = <20 4 2>;
status = "disabled";
};
};
ranges;
aic: interrupt-controller@fffff000 {
- #interrupt-cells = <2>;
+ #interrupt-cells = <3>;
compatible = "atmel,at91rm9200-aic";
interrupt-controller;
reg = <0xfffff000 0x200>;
+ atmel,external-irqs = <30 31>;
};
pmc: pmc@fffffc00 {
pit: timer@fffffd30 {
compatible = "atmel,at91sam9260-pit";
reg = <0xfffffd30 0xf>;
- interrupts = <1 4>;
+ interrupts = <1 4 7>;
};
tcb0: timer@fff7c000 {
compatible = "atmel,at91rm9200-tcb";
reg = <0xfff7c000 0x100>;
- interrupts = <19 4>;
+ interrupts = <19 4 0>;
};
rstc@fffffd00 {
pioA: gpio@fffff200 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff200 0x100>;
- interrupts = <2 4>;
+ interrupts = <2 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
pioB: gpio@fffff400 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff400 0x100>;
- interrupts = <3 4>;
+ interrupts = <3 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
pioC: gpio@fffff600 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff600 0x100>;
- interrupts = <4 4>;
+ interrupts = <4 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
pioD: gpio@fffff800 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff800 0x100>;
- interrupts = <4 4>;
+ interrupts = <4 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
pioE: gpio@fffffa00 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffffa00 0x100>;
- interrupts = <4 4>;
+ interrupts = <4 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
dbgu: serial@ffffee00 {
compatible = "atmel,at91sam9260-usart";
reg = <0xffffee00 0x200>;
- interrupts = <1 4>;
+ interrupts = <1 4 7>;
status = "disabled";
};
usart0: serial@fff8c000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfff8c000 0x200>;
- interrupts = <7 4>;
+ interrupts = <7 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";
usart1: serial@fff90000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfff90000 0x200>;
- interrupts = <8 4>;
+ interrupts = <8 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";
usart2: serial@fff94000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfff94000 0x200>;
- interrupts = <9 4>;
+ interrupts = <9 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";
macb0: ethernet@fffbc000 {
compatible = "cdns,at32ap7000-macb", "cdns,macb";
reg = <0xfffbc000 0x100>;
- interrupts = <21 4>;
+ interrupts = <21 4 3>;
status = "disabled";
};
usb1: gadget@fff78000 {
compatible = "atmel,at91rm9200-udc";
reg = <0xfff78000 0x4000>;
- interrupts = <24 4>;
+ interrupts = <24 4 2>;
status = "disabled";
};
};
usb0: ohci@00a00000 {
compatible = "atmel,at91rm9200-ohci", "usb-ohci";
reg = <0x00a00000 0x100000>;
- interrupts = <29 4>;
+ interrupts = <29 4 2>;
status = "disabled";
};
};
ranges;
aic: interrupt-controller@fffff000 {
- #interrupt-cells = <2>;
+ #interrupt-cells = <3>;
compatible = "atmel,at91rm9200-aic";
interrupt-controller;
reg = <0xfffff000 0x200>;
+ atmel,external-irqs = <31>;
};
ramc0: ramc@ffffe400 {
pit: timer@fffffd30 {
compatible = "atmel,at91sam9260-pit";
reg = <0xfffffd30 0xf>;
- interrupts = <1 4>;
+ interrupts = <1 4 7>;
};
tcb0: timer@fff7c000 {
compatible = "atmel,at91rm9200-tcb";
reg = <0xfff7c000 0x100>;
- interrupts = <18 4>;
+ interrupts = <18 4 0>;
};
tcb1: timer@fffd4000 {
compatible = "atmel,at91rm9200-tcb";
reg = <0xfffd4000 0x100>;
- interrupts = <18 4>;
+ interrupts = <18 4 0>;
};
dma: dma-controller@ffffec00 {
compatible = "atmel,at91sam9g45-dma";
reg = <0xffffec00 0x200>;
- interrupts = <21 4>;
+ interrupts = <21 4 0>;
};
pioA: gpio@fffff200 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff200 0x100>;
- interrupts = <2 4>;
+ interrupts = <2 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
pioB: gpio@fffff400 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff400 0x100>;
- interrupts = <3 4>;
+ interrupts = <3 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
pioC: gpio@fffff600 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff600 0x100>;
- interrupts = <4 4>;
+ interrupts = <4 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
pioD: gpio@fffff800 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff800 0x100>;
- interrupts = <5 4>;
+ interrupts = <5 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
pioE: gpio@fffffa00 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffffa00 0x100>;
- interrupts = <5 4>;
+ interrupts = <5 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
dbgu: serial@ffffee00 {
compatible = "atmel,at91sam9260-usart";
reg = <0xffffee00 0x200>;
- interrupts = <1 4>;
+ interrupts = <1 4 7>;
status = "disabled";
};
usart0: serial@fff8c000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfff8c000 0x200>;
- interrupts = <7 4>;
+ interrupts = <7 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";
usart1: serial@fff90000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfff90000 0x200>;
- interrupts = <8 4>;
+ interrupts = <8 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";
usart2: serial@fff94000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfff94000 0x200>;
- interrupts = <9 4>;
+ interrupts = <9 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";
usart3: serial@fff98000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfff98000 0x200>;
- interrupts = <10 4>;
+ interrupts = <10 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";
macb0: ethernet@fffbc000 {
compatible = "cdns,at32ap7000-macb", "cdns,macb";
reg = <0xfffbc000 0x100>;
- interrupts = <25 4>;
+ interrupts = <25 4 3>;
status = "disabled";
};
adc0: adc@fffb0000 {
compatible = "atmel,at91sam9260-adc";
reg = <0xfffb0000 0x100>;
- interrupts = <20 4>;
+ interrupts = <20 4 0>;
atmel,adc-use-external-triggers;
atmel,adc-channels-used = <0xff>;
atmel,adc-vref = <3300>;
usb0: ohci@00700000 {
compatible = "atmel,at91rm9200-ohci", "usb-ohci";
reg = <0x00700000 0x100000>;
- interrupts = <22 4>;
+ interrupts = <22 4 2>;
status = "disabled";
};
usb1: ehci@00800000 {
compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
reg = <0x00800000 0x100000>;
- interrupts = <22 4>;
+ interrupts = <22 4 2>;
status = "disabled";
};
};
ranges;
aic: interrupt-controller@fffff000 {
- #interrupt-cells = <2>;
+ #interrupt-cells = <3>;
compatible = "atmel,at91rm9200-aic";
interrupt-controller;
reg = <0xfffff000 0x200>;
pit: timer@fffffe30 {
compatible = "atmel,at91sam9260-pit";
reg = <0xfffffe30 0xf>;
- interrupts = <1 4>;
+ interrupts = <1 4 7>;
};
shdwc@fffffe10 {
tcb0: timer@f8008000 {
compatible = "atmel,at91sam9x5-tcb";
reg = <0xf8008000 0x100>;
- interrupts = <17 4>;
+ interrupts = <17 4 0>;
};
tcb1: timer@f800c000 {
compatible = "atmel,at91sam9x5-tcb";
reg = <0xf800c000 0x100>;
- interrupts = <17 4>;
+ interrupts = <17 4 0>;
};
dma: dma-controller@ffffec00 {
compatible = "atmel,at91sam9g45-dma";
reg = <0xffffec00 0x200>;
- interrupts = <20 4>;
+ interrupts = <20 4 0>;
};
pioA: gpio@fffff400 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff400 0x100>;
- interrupts = <2 4>;
+ interrupts = <2 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
pioB: gpio@fffff600 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff600 0x100>;
- interrupts = <2 4>;
+ interrupts = <2 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
pioC: gpio@fffff800 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff800 0x100>;
- interrupts = <3 4>;
+ interrupts = <3 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
pioD: gpio@fffffa00 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffffa00 0x100>;
- interrupts = <3 4>;
+ interrupts = <3 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
dbgu: serial@fffff200 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffff200 0x200>;
- interrupts = <1 4>;
+ interrupts = <1 4 7>;
status = "disabled";
};
usart0: serial@f801c000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf801c000 0x4000>;
- interrupts = <5 4>;
+ interrupts = <5 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";
usart1: serial@f8020000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8020000 0x4000>;
- interrupts = <6 4>;
+ interrupts = <6 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";
usart2: serial@f8024000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8024000 0x4000>;
- interrupts = <7 4>;
+ interrupts = <7 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";
usart3: serial@f8028000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8028000 0x4000>;
- interrupts = <8 4>;
+ interrupts = <8 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";
usb0: ohci@00500000 {
compatible = "atmel,at91rm9200-ohci", "usb-ohci";
reg = <0x00500000 0x00100000>;
- interrupts = <22 4>;
+ interrupts = <22 4 2>;
status = "disabled";
};
};
ranges;
aic: interrupt-controller@fffff000 {
- #interrupt-cells = <2>;
+ #interrupt-cells = <3>;
compatible = "atmel,at91rm9200-aic";
interrupt-controller;
reg = <0xfffff000 0x200>;
+ atmel,external-irqs = <31>;
};
ramc0: ramc@ffffe800 {
pit: timer@fffffe30 {
compatible = "atmel,at91sam9260-pit";
reg = <0xfffffe30 0xf>;
- interrupts = <1 4>;
+ interrupts = <1 4 7>;
};
tcb0: timer@f8008000 {
compatible = "atmel,at91sam9x5-tcb";
reg = <0xf8008000 0x100>;
- interrupts = <17 4>;
+ interrupts = <17 4 0>;
};
tcb1: timer@f800c000 {
compatible = "atmel,at91sam9x5-tcb";
reg = <0xf800c000 0x100>;
- interrupts = <17 4>;
+ interrupts = <17 4 0>;
};
dma0: dma-controller@ffffec00 {
compatible = "atmel,at91sam9g45-dma";
reg = <0xffffec00 0x200>;
- interrupts = <20 4>;
+ interrupts = <20 4 0>;
};
dma1: dma-controller@ffffee00 {
compatible = "atmel,at91sam9g45-dma";
reg = <0xffffee00 0x200>;
- interrupts = <21 4>;
+ interrupts = <21 4 0>;
};
pioA: gpio@fffff400 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff400 0x100>;
- interrupts = <2 4>;
+ interrupts = <2 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
pioB: gpio@fffff600 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff600 0x100>;
- interrupts = <2 4>;
+ interrupts = <2 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
pioC: gpio@fffff800 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff800 0x100>;
- interrupts = <3 4>;
+ interrupts = <3 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
pioD: gpio@fffffa00 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffffa00 0x100>;
- interrupts = <3 4>;
+ interrupts = <3 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
dbgu: serial@fffff200 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffff200 0x200>;
- interrupts = <1 4>;
+ interrupts = <1 4 7>;
status = "disabled";
};
usart0: serial@f801c000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf801c000 0x200>;
- interrupts = <5 4>;
+ interrupts = <5 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";
usart1: serial@f8020000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8020000 0x200>;
- interrupts = <6 4>;
+ interrupts = <6 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";
usart2: serial@f8024000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8024000 0x200>;
- interrupts = <7 4>;
+ interrupts = <7 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";
macb0: ethernet@f802c000 {
compatible = "cdns,at32ap7000-macb", "cdns,macb";
reg = <0xf802c000 0x100>;
- interrupts = <24 4>;
+ interrupts = <24 4 3>;
status = "disabled";
};
macb1: ethernet@f8030000 {
compatible = "cdns,at32ap7000-macb", "cdns,macb";
reg = <0xf8030000 0x100>;
- interrupts = <27 4>;
+ interrupts = <27 4 3>;
status = "disabled";
};
adc0: adc@f804c000 {
compatible = "atmel,at91sam9260-adc";
reg = <0xf804c000 0x100>;
- interrupts = <19 4>;
+ interrupts = <19 4 0>;
atmel,adc-use-external;
atmel,adc-channels-used = <0xffff>;
atmel,adc-vref = <3300>;
usb0: ohci@00600000 {
compatible = "atmel,at91rm9200-ohci", "usb-ohci";
reg = <0x00600000 0x100000>;
- interrupts = <22 4>;
+ interrupts = <22 4 2>;
status = "disabled";
};
usb1: ehci@00700000 {
compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
reg = <0x00700000 0x100000>;
- interrupts = <22 4>;
+ interrupts = <22 4 2>;
status = "disabled";
};
};
#include <asm/mach/irq.h>
#include <asm/mach/time.h>
-/*
- * No architecture-specific irq_finish function defined in arm/arch/irqs.h.
- */
-#ifndef irq_finish
-#define irq_finish(irq) do { } while (0)
-#endif
-
unsigned long irq_err_count;
int arch_show_interrupts(struct seq_file *p, int prec)
generic_handle_irq(irq);
}
- /* AT91 specific workaround */
- irq_finish(irq);
-
irq_exit();
set_irq_regs(old_regs);
}
config SOC_AT91SAM9
bool
select CPU_ARM926T
+ select MULTI_IRQ_HANDLER
+ select SPARSE_IRQ
select AT91_SAM9_TIME
select AT91_SAM9_SMC
config SOC_AT91RM9200
bool "AT91RM9200"
select CPU_ARM920T
+ select MULTI_IRQ_HANDLER
+ select SPARSE_IRQ
select GENERIC_CLOCKEVENTS
select HAVE_AT91_DBGU0
config ARCH_AT91X40
bool "AT91x40"
depends on !MMU
+ select MULTI_IRQ_HANDLER
+ select SPARSE_IRQ
select ARCH_USES_GETTIMEOFFSET
endchoice
#include <asm/mach/map.h>
#include <asm/system_misc.h>
#include <mach/at91rm9200.h>
+#include <mach/at91_aic.h>
#include <mach/at91_pmc.h>
#include <mach/at91_st.h>
#include <mach/cpu.h>
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91RM9200_ID_UHP,
- .end = AT91RM9200_ID_UHP,
+ .start = NR_IRQS_LEGACY + AT91RM9200_ID_UHP,
+ .end = NR_IRQS_LEGACY + AT91RM9200_ID_UHP,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91RM9200_ID_UDP,
- .end = AT91RM9200_ID_UDP,
+ .start = NR_IRQS_LEGACY + AT91RM9200_ID_UDP,
+ .end = NR_IRQS_LEGACY + AT91RM9200_ID_UDP,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91RM9200_ID_EMAC,
- .end = AT91RM9200_ID_EMAC,
+ .start = NR_IRQS_LEGACY + AT91RM9200_ID_EMAC,
+ .end = NR_IRQS_LEGACY + AT91RM9200_ID_EMAC,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91RM9200_ID_MCI,
- .end = AT91RM9200_ID_MCI,
+ .start = NR_IRQS_LEGACY + AT91RM9200_ID_MCI,
+ .end = NR_IRQS_LEGACY + AT91RM9200_ID_MCI,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91RM9200_ID_TWI,
- .end = AT91RM9200_ID_TWI,
+ .start = NR_IRQS_LEGACY + AT91RM9200_ID_TWI,
+ .end = NR_IRQS_LEGACY + AT91RM9200_ID_TWI,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91RM9200_ID_SPI,
- .end = AT91RM9200_ID_SPI,
+ .start = NR_IRQS_LEGACY + AT91RM9200_ID_SPI,
+ .end = NR_IRQS_LEGACY + AT91RM9200_ID_SPI,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91RM9200_ID_TC0,
- .end = AT91RM9200_ID_TC0,
+ .start = NR_IRQS_LEGACY + AT91RM9200_ID_TC0,
+ .end = NR_IRQS_LEGACY + AT91RM9200_ID_TC0,
.flags = IORESOURCE_IRQ,
},
[2] = {
- .start = AT91RM9200_ID_TC1,
- .end = AT91RM9200_ID_TC1,
+ .start = NR_IRQS_LEGACY + AT91RM9200_ID_TC1,
+ .end = NR_IRQS_LEGACY + AT91RM9200_ID_TC1,
.flags = IORESOURCE_IRQ,
},
[3] = {
- .start = AT91RM9200_ID_TC2,
- .end = AT91RM9200_ID_TC2,
+ .start = NR_IRQS_LEGACY + AT91RM9200_ID_TC2,
+ .end = NR_IRQS_LEGACY + AT91RM9200_ID_TC2,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91RM9200_ID_TC3,
- .end = AT91RM9200_ID_TC3,
+ .start = NR_IRQS_LEGACY + AT91RM9200_ID_TC3,
+ .end = NR_IRQS_LEGACY + AT91RM9200_ID_TC3,
.flags = IORESOURCE_IRQ,
},
[2] = {
- .start = AT91RM9200_ID_TC4,
- .end = AT91RM9200_ID_TC4,
+ .start = NR_IRQS_LEGACY + AT91RM9200_ID_TC4,
+ .end = NR_IRQS_LEGACY + AT91RM9200_ID_TC4,
.flags = IORESOURCE_IRQ,
},
[3] = {
- .start = AT91RM9200_ID_TC5,
- .end = AT91RM9200_ID_TC5,
+ .start = NR_IRQS_LEGACY + AT91RM9200_ID_TC5,
+ .end = NR_IRQS_LEGACY + AT91RM9200_ID_TC5,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91_ID_SYS,
- .end = AT91_ID_SYS,
+ .start = NR_IRQS_LEGACY + AT91_ID_SYS,
+ .end = NR_IRQS_LEGACY + AT91_ID_SYS,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91RM9200_ID_SSC0,
- .end = AT91RM9200_ID_SSC0,
+ .start = NR_IRQS_LEGACY + AT91RM9200_ID_SSC0,
+ .end = NR_IRQS_LEGACY + AT91RM9200_ID_SSC0,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91RM9200_ID_SSC1,
- .end = AT91RM9200_ID_SSC1,
+ .start = NR_IRQS_LEGACY + AT91RM9200_ID_SSC1,
+ .end = NR_IRQS_LEGACY + AT91RM9200_ID_SSC1,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91RM9200_ID_SSC2,
- .end = AT91RM9200_ID_SSC2,
+ .start = NR_IRQS_LEGACY + AT91RM9200_ID_SSC2,
+ .end = NR_IRQS_LEGACY + AT91RM9200_ID_SSC2,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91_ID_SYS,
- .end = AT91_ID_SYS,
+ .start = NR_IRQS_LEGACY + AT91_ID_SYS,
+ .end = NR_IRQS_LEGACY + AT91_ID_SYS,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91RM9200_ID_US0,
- .end = AT91RM9200_ID_US0,
+ .start = NR_IRQS_LEGACY + AT91RM9200_ID_US0,
+ .end = NR_IRQS_LEGACY + AT91RM9200_ID_US0,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91RM9200_ID_US1,
- .end = AT91RM9200_ID_US1,
+ .start = NR_IRQS_LEGACY + AT91RM9200_ID_US1,
+ .end = NR_IRQS_LEGACY + AT91RM9200_ID_US1,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91RM9200_ID_US2,
- .end = AT91RM9200_ID_US2,
+ .start = NR_IRQS_LEGACY + AT91RM9200_ID_US2,
+ .end = NR_IRQS_LEGACY + AT91RM9200_ID_US2,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91RM9200_ID_US3,
- .end = AT91RM9200_ID_US3,
+ .start = NR_IRQS_LEGACY + AT91RM9200_ID_US3,
+ .end = NR_IRQS_LEGACY + AT91RM9200_ID_US3,
.flags = IORESOURCE_IRQ,
},
};
#include <mach/cpu.h>
#include <mach/at91_dbgu.h>
#include <mach/at91sam9260.h>
+#include <mach/at91_aic.h>
#include <mach/at91_pmc.h>
#include <mach/at91_rstc.h>
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9260_ID_UHP,
- .end = AT91SAM9260_ID_UHP,
+ .start = NR_IRQS_LEGACY + AT91SAM9260_ID_UHP,
+ .end = NR_IRQS_LEGACY + AT91SAM9260_ID_UHP,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9260_ID_UDP,
- .end = AT91SAM9260_ID_UDP,
+ .start = NR_IRQS_LEGACY + AT91SAM9260_ID_UDP,
+ .end = NR_IRQS_LEGACY + AT91SAM9260_ID_UDP,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9260_ID_EMAC,
- .end = AT91SAM9260_ID_EMAC,
+ .start = NR_IRQS_LEGACY + AT91SAM9260_ID_EMAC,
+ .end = NR_IRQS_LEGACY + AT91SAM9260_ID_EMAC,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9260_ID_MCI,
- .end = AT91SAM9260_ID_MCI,
+ .start = NR_IRQS_LEGACY + AT91SAM9260_ID_MCI,
+ .end = NR_IRQS_LEGACY + AT91SAM9260_ID_MCI,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9260_ID_MCI,
- .end = AT91SAM9260_ID_MCI,
+ .start = NR_IRQS_LEGACY + AT91SAM9260_ID_MCI,
+ .end = NR_IRQS_LEGACY + AT91SAM9260_ID_MCI,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9260_ID_TWI,
- .end = AT91SAM9260_ID_TWI,
+ .start = NR_IRQS_LEGACY + AT91SAM9260_ID_TWI,
+ .end = NR_IRQS_LEGACY + AT91SAM9260_ID_TWI,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9260_ID_SPI0,
- .end = AT91SAM9260_ID_SPI0,
+ .start = NR_IRQS_LEGACY + AT91SAM9260_ID_SPI0,
+ .end = NR_IRQS_LEGACY + AT91SAM9260_ID_SPI0,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9260_ID_SPI1,
- .end = AT91SAM9260_ID_SPI1,
+ .start = NR_IRQS_LEGACY + AT91SAM9260_ID_SPI1,
+ .end = NR_IRQS_LEGACY + AT91SAM9260_ID_SPI1,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9260_ID_TC0,
- .end = AT91SAM9260_ID_TC0,
+ .start = NR_IRQS_LEGACY + AT91SAM9260_ID_TC0,
+ .end = NR_IRQS_LEGACY + AT91SAM9260_ID_TC0,
.flags = IORESOURCE_IRQ,
},
[2] = {
- .start = AT91SAM9260_ID_TC1,
- .end = AT91SAM9260_ID_TC1,
+ .start = NR_IRQS_LEGACY + AT91SAM9260_ID_TC1,
+ .end = NR_IRQS_LEGACY + AT91SAM9260_ID_TC1,
.flags = IORESOURCE_IRQ,
},
[3] = {
- .start = AT91SAM9260_ID_TC2,
- .end = AT91SAM9260_ID_TC2,
+ .start = NR_IRQS_LEGACY + AT91SAM9260_ID_TC2,
+ .end = NR_IRQS_LEGACY + AT91SAM9260_ID_TC2,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9260_ID_TC3,
- .end = AT91SAM9260_ID_TC3,
+ .start = NR_IRQS_LEGACY + AT91SAM9260_ID_TC3,
+ .end = NR_IRQS_LEGACY + AT91SAM9260_ID_TC3,
.flags = IORESOURCE_IRQ,
},
[2] = {
- .start = AT91SAM9260_ID_TC4,
- .end = AT91SAM9260_ID_TC4,
+ .start = NR_IRQS_LEGACY + AT91SAM9260_ID_TC4,
+ .end = NR_IRQS_LEGACY + AT91SAM9260_ID_TC4,
.flags = IORESOURCE_IRQ,
},
[3] = {
- .start = AT91SAM9260_ID_TC5,
- .end = AT91SAM9260_ID_TC5,
+ .start = NR_IRQS_LEGACY + AT91SAM9260_ID_TC5,
+ .end = NR_IRQS_LEGACY + AT91SAM9260_ID_TC5,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9260_ID_SSC,
- .end = AT91SAM9260_ID_SSC,
+ .start = NR_IRQS_LEGACY + AT91SAM9260_ID_SSC,
+ .end = NR_IRQS_LEGACY + AT91SAM9260_ID_SSC,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91_ID_SYS,
- .end = AT91_ID_SYS,
+ .start = NR_IRQS_LEGACY + AT91_ID_SYS,
+ .end = NR_IRQS_LEGACY + AT91_ID_SYS,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9260_ID_US0,
- .end = AT91SAM9260_ID_US0,
+ .start = NR_IRQS_LEGACY + AT91SAM9260_ID_US0,
+ .end = NR_IRQS_LEGACY + AT91SAM9260_ID_US0,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9260_ID_US1,
- .end = AT91SAM9260_ID_US1,
+ .start = NR_IRQS_LEGACY + AT91SAM9260_ID_US1,
+ .end = NR_IRQS_LEGACY + AT91SAM9260_ID_US1,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9260_ID_US2,
- .end = AT91SAM9260_ID_US2,
+ .start = NR_IRQS_LEGACY + AT91SAM9260_ID_US2,
+ .end = NR_IRQS_LEGACY + AT91SAM9260_ID_US2,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9260_ID_US3,
- .end = AT91SAM9260_ID_US3,
+ .start = NR_IRQS_LEGACY + AT91SAM9260_ID_US3,
+ .end = NR_IRQS_LEGACY + AT91SAM9260_ID_US3,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9260_ID_US4,
- .end = AT91SAM9260_ID_US4,
+ .start = NR_IRQS_LEGACY + AT91SAM9260_ID_US4,
+ .end = NR_IRQS_LEGACY + AT91SAM9260_ID_US4,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9260_ID_US5,
- .end = AT91SAM9260_ID_US5,
+ .start = NR_IRQS_LEGACY + AT91SAM9260_ID_US5,
+ .end = NR_IRQS_LEGACY + AT91SAM9260_ID_US5,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9260_ID_ADC,
- .end = AT91SAM9260_ID_ADC,
+ .start = NR_IRQS_LEGACY + AT91SAM9260_ID_ADC,
+ .end = NR_IRQS_LEGACY + AT91SAM9260_ID_ADC,
.flags = IORESOURCE_IRQ,
},
};
#include <asm/system_misc.h>
#include <mach/cpu.h>
#include <mach/at91sam9261.h>
+#include <mach/at91_aic.h>
#include <mach/at91_pmc.h>
#include <mach/at91_rstc.h>
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9261_ID_UHP,
- .end = AT91SAM9261_ID_UHP,
+ .start = NR_IRQS_LEGACY + AT91SAM9261_ID_UHP,
+ .end = NR_IRQS_LEGACY + AT91SAM9261_ID_UHP,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9261_ID_UDP,
- .end = AT91SAM9261_ID_UDP,
+ .start = NR_IRQS_LEGACY + AT91SAM9261_ID_UDP,
+ .end = NR_IRQS_LEGACY + AT91SAM9261_ID_UDP,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9261_ID_MCI,
- .end = AT91SAM9261_ID_MCI,
+ .start = NR_IRQS_LEGACY + AT91SAM9261_ID_MCI,
+ .end = NR_IRQS_LEGACY + AT91SAM9261_ID_MCI,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9261_ID_TWI,
- .end = AT91SAM9261_ID_TWI,
+ .start = NR_IRQS_LEGACY + AT91SAM9261_ID_TWI,
+ .end = NR_IRQS_LEGACY + AT91SAM9261_ID_TWI,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9261_ID_SPI0,
- .end = AT91SAM9261_ID_SPI0,
+ .start = NR_IRQS_LEGACY + AT91SAM9261_ID_SPI0,
+ .end = NR_IRQS_LEGACY + AT91SAM9261_ID_SPI0,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9261_ID_SPI1,
- .end = AT91SAM9261_ID_SPI1,
+ .start = NR_IRQS_LEGACY + AT91SAM9261_ID_SPI1,
+ .end = NR_IRQS_LEGACY + AT91SAM9261_ID_SPI1,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9261_ID_LCDC,
- .end = AT91SAM9261_ID_LCDC,
+ .start = NR_IRQS_LEGACY + AT91SAM9261_ID_LCDC,
+ .end = NR_IRQS_LEGACY + AT91SAM9261_ID_LCDC,
.flags = IORESOURCE_IRQ,
},
#if defined(CONFIG_FB_INTSRAM)
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9261_ID_TC0,
- .end = AT91SAM9261_ID_TC0,
+ .start = NR_IRQS_LEGACY + AT91SAM9261_ID_TC0,
+ .end = NR_IRQS_LEGACY + AT91SAM9261_ID_TC0,
.flags = IORESOURCE_IRQ,
},
[2] = {
- .start = AT91SAM9261_ID_TC1,
- .end = AT91SAM9261_ID_TC1,
+ .start = NR_IRQS_LEGACY + AT91SAM9261_ID_TC1,
+ .end = NR_IRQS_LEGACY + AT91SAM9261_ID_TC1,
.flags = IORESOURCE_IRQ,
},
[3] = {
- .start = AT91SAM9261_ID_TC2,
- .end = AT91SAM9261_ID_TC2,
+ .start = NR_IRQS_LEGACY + AT91SAM9261_ID_TC2,
+ .end = NR_IRQS_LEGACY + AT91SAM9261_ID_TC2,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9261_ID_SSC0,
- .end = AT91SAM9261_ID_SSC0,
+ .start = NR_IRQS_LEGACY + AT91SAM9261_ID_SSC0,
+ .end = NR_IRQS_LEGACY + AT91SAM9261_ID_SSC0,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9261_ID_SSC1,
- .end = AT91SAM9261_ID_SSC1,
+ .start = NR_IRQS_LEGACY + AT91SAM9261_ID_SSC1,
+ .end = NR_IRQS_LEGACY + AT91SAM9261_ID_SSC1,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9261_ID_SSC2,
- .end = AT91SAM9261_ID_SSC2,
+ .start = NR_IRQS_LEGACY + AT91SAM9261_ID_SSC2,
+ .end = NR_IRQS_LEGACY + AT91SAM9261_ID_SSC2,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91_ID_SYS,
- .end = AT91_ID_SYS,
+ .start = NR_IRQS_LEGACY + AT91_ID_SYS,
+ .end = NR_IRQS_LEGACY + AT91_ID_SYS,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9261_ID_US0,
- .end = AT91SAM9261_ID_US0,
+ .start = NR_IRQS_LEGACY + AT91SAM9261_ID_US0,
+ .end = NR_IRQS_LEGACY + AT91SAM9261_ID_US0,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9261_ID_US1,
- .end = AT91SAM9261_ID_US1,
+ .start = NR_IRQS_LEGACY + AT91SAM9261_ID_US1,
+ .end = NR_IRQS_LEGACY + AT91SAM9261_ID_US1,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9261_ID_US2,
- .end = AT91SAM9261_ID_US2,
+ .start = NR_IRQS_LEGACY + AT91SAM9261_ID_US2,
+ .end = NR_IRQS_LEGACY + AT91SAM9261_ID_US2,
.flags = IORESOURCE_IRQ,
},
};
#include <asm/mach/map.h>
#include <asm/system_misc.h>
#include <mach/at91sam9263.h>
+#include <mach/at91_aic.h>
#include <mach/at91_pmc.h>
#include <mach/at91_rstc.h>
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9263_ID_UHP,
- .end = AT91SAM9263_ID_UHP,
+ .start = NR_IRQS_LEGACY + AT91SAM9263_ID_UHP,
+ .end = NR_IRQS_LEGACY + AT91SAM9263_ID_UHP,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9263_ID_UDP,
- .end = AT91SAM9263_ID_UDP,
+ .start = NR_IRQS_LEGACY + AT91SAM9263_ID_UDP,
+ .end = NR_IRQS_LEGACY + AT91SAM9263_ID_UDP,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9263_ID_EMAC,
- .end = AT91SAM9263_ID_EMAC,
+ .start = NR_IRQS_LEGACY + AT91SAM9263_ID_EMAC,
+ .end = NR_IRQS_LEGACY + AT91SAM9263_ID_EMAC,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9263_ID_MCI0,
- .end = AT91SAM9263_ID_MCI0,
+ .start = NR_IRQS_LEGACY + AT91SAM9263_ID_MCI0,
+ .end = NR_IRQS_LEGACY + AT91SAM9263_ID_MCI0,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9263_ID_MCI1,
- .end = AT91SAM9263_ID_MCI1,
+ .start = NR_IRQS_LEGACY + AT91SAM9263_ID_MCI1,
+ .end = NR_IRQS_LEGACY + AT91SAM9263_ID_MCI1,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9263_ID_TWI,
- .end = AT91SAM9263_ID_TWI,
+ .start = NR_IRQS_LEGACY + AT91SAM9263_ID_TWI,
+ .end = NR_IRQS_LEGACY + AT91SAM9263_ID_TWI,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9263_ID_SPI0,
- .end = AT91SAM9263_ID_SPI0,
+ .start = NR_IRQS_LEGACY + AT91SAM9263_ID_SPI0,
+ .end = NR_IRQS_LEGACY + AT91SAM9263_ID_SPI0,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9263_ID_SPI1,
- .end = AT91SAM9263_ID_SPI1,
+ .start = NR_IRQS_LEGACY + AT91SAM9263_ID_SPI1,
+ .end = NR_IRQS_LEGACY + AT91SAM9263_ID_SPI1,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9263_ID_AC97C,
- .end = AT91SAM9263_ID_AC97C,
+ .start = NR_IRQS_LEGACY + AT91SAM9263_ID_AC97C,
+ .end = NR_IRQS_LEGACY + AT91SAM9263_ID_AC97C,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9263_ID_CAN,
- .end = AT91SAM9263_ID_CAN,
+ .start = NR_IRQS_LEGACY + AT91SAM9263_ID_CAN,
+ .end = NR_IRQS_LEGACY + AT91SAM9263_ID_CAN,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9263_ID_LCDC,
- .end = AT91SAM9263_ID_LCDC,
+ .start = NR_IRQS_LEGACY + AT91SAM9263_ID_LCDC,
+ .end = NR_IRQS_LEGACY + AT91SAM9263_ID_LCDC,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9263_ID_ISI,
- .end = AT91SAM9263_ID_ISI,
+ .start = NR_IRQS_LEGACY + AT91SAM9263_ID_ISI,
+ .end = NR_IRQS_LEGACY + AT91SAM9263_ID_ISI,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9263_ID_TCB,
- .end = AT91SAM9263_ID_TCB,
+ .start = NR_IRQS_LEGACY + AT91SAM9263_ID_TCB,
+ .end = NR_IRQS_LEGACY + AT91SAM9263_ID_TCB,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9263_ID_PWMC,
- .end = AT91SAM9263_ID_PWMC,
+ .start = NR_IRQS_LEGACY + AT91SAM9263_ID_PWMC,
+ .end = NR_IRQS_LEGACY + AT91SAM9263_ID_PWMC,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9263_ID_SSC0,
- .end = AT91SAM9263_ID_SSC0,
+ .start = NR_IRQS_LEGACY + AT91SAM9263_ID_SSC0,
+ .end = NR_IRQS_LEGACY + AT91SAM9263_ID_SSC0,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9263_ID_SSC1,
- .end = AT91SAM9263_ID_SSC1,
+ .start = NR_IRQS_LEGACY + AT91SAM9263_ID_SSC1,
+ .end = NR_IRQS_LEGACY + AT91SAM9263_ID_SSC1,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91_ID_SYS,
- .end = AT91_ID_SYS,
+ .start = NR_IRQS_LEGACY + AT91_ID_SYS,
+ .end = NR_IRQS_LEGACY + AT91_ID_SYS,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9263_ID_US0,
- .end = AT91SAM9263_ID_US0,
+ .start = NR_IRQS_LEGACY + AT91SAM9263_ID_US0,
+ .end = NR_IRQS_LEGACY + AT91SAM9263_ID_US0,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9263_ID_US1,
- .end = AT91SAM9263_ID_US1,
+ .start = NR_IRQS_LEGACY + AT91SAM9263_ID_US1,
+ .end = NR_IRQS_LEGACY + AT91SAM9263_ID_US1,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9263_ID_US2,
- .end = AT91SAM9263_ID_US2,
+ .start = NR_IRQS_LEGACY + AT91SAM9263_ID_US2,
+ .end = NR_IRQS_LEGACY + AT91SAM9263_ID_US2,
.flags = IORESOURCE_IRQ,
},
};
.name = "at91_tick",
.flags = IRQF_SHARED | IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL,
.handler = at91sam926x_pit_interrupt,
- .irq = AT91_ID_SYS,
+ .irq = NR_IRQS_LEGACY + AT91_ID_SYS,
};
static void at91sam926x_pit_reset(void)
#include <asm/mach/map.h>
#include <asm/system_misc.h>
#include <mach/at91sam9g45.h>
+#include <mach/at91_aic.h>
#include <mach/at91_pmc.h>
#include <mach/cpu.h>
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9G45_ID_DMA,
- .end = AT91SAM9G45_ID_DMA,
+ .start = NR_IRQS_LEGACY + AT91SAM9G45_ID_DMA,
+ .end = NR_IRQS_LEGACY + AT91SAM9G45_ID_DMA,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9G45_ID_UHPHS,
- .end = AT91SAM9G45_ID_UHPHS,
+ .start = NR_IRQS_LEGACY + AT91SAM9G45_ID_UHPHS,
+ .end = NR_IRQS_LEGACY + AT91SAM9G45_ID_UHPHS,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9G45_ID_UHPHS,
- .end = AT91SAM9G45_ID_UHPHS,
+ .start = NR_IRQS_LEGACY + AT91SAM9G45_ID_UHPHS,
+ .end = NR_IRQS_LEGACY + AT91SAM9G45_ID_UHPHS,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[2] = {
- .start = AT91SAM9G45_ID_UDPHS,
- .end = AT91SAM9G45_ID_UDPHS,
+ .start = NR_IRQS_LEGACY + AT91SAM9G45_ID_UDPHS,
+ .end = NR_IRQS_LEGACY + AT91SAM9G45_ID_UDPHS,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9G45_ID_EMAC,
- .end = AT91SAM9G45_ID_EMAC,
+ .start = NR_IRQS_LEGACY + AT91SAM9G45_ID_EMAC,
+ .end = NR_IRQS_LEGACY + AT91SAM9G45_ID_EMAC,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9G45_ID_MCI0,
- .end = AT91SAM9G45_ID_MCI0,
+ .start = NR_IRQS_LEGACY + AT91SAM9G45_ID_MCI0,
+ .end = NR_IRQS_LEGACY + AT91SAM9G45_ID_MCI0,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9G45_ID_MCI1,
- .end = AT91SAM9G45_ID_MCI1,
+ .start = NR_IRQS_LEGACY + AT91SAM9G45_ID_MCI1,
+ .end = NR_IRQS_LEGACY + AT91SAM9G45_ID_MCI1,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9G45_ID_TWI0,
- .end = AT91SAM9G45_ID_TWI0,
+ .start = NR_IRQS_LEGACY + AT91SAM9G45_ID_TWI0,
+ .end = NR_IRQS_LEGACY + AT91SAM9G45_ID_TWI0,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9G45_ID_TWI1,
- .end = AT91SAM9G45_ID_TWI1,
+ .start = NR_IRQS_LEGACY + AT91SAM9G45_ID_TWI1,
+ .end = NR_IRQS_LEGACY + AT91SAM9G45_ID_TWI1,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9G45_ID_SPI0,
- .end = AT91SAM9G45_ID_SPI0,
+ .start = NR_IRQS_LEGACY + AT91SAM9G45_ID_SPI0,
+ .end = NR_IRQS_LEGACY + AT91SAM9G45_ID_SPI0,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9G45_ID_SPI1,
- .end = AT91SAM9G45_ID_SPI1,
+ .start = NR_IRQS_LEGACY + AT91SAM9G45_ID_SPI1,
+ .end = NR_IRQS_LEGACY + AT91SAM9G45_ID_SPI1,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9G45_ID_AC97C,
- .end = AT91SAM9G45_ID_AC97C,
+ .start = NR_IRQS_LEGACY + AT91SAM9G45_ID_AC97C,
+ .end = NR_IRQS_LEGACY + AT91SAM9G45_ID_AC97C,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9G45_ID_ISI,
- .end = AT91SAM9G45_ID_ISI,
+ .start = NR_IRQS_LEGACY + AT91SAM9G45_ID_ISI,
+ .end = NR_IRQS_LEGACY + AT91SAM9G45_ID_ISI,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9G45_ID_LCDC,
- .end = AT91SAM9G45_ID_LCDC,
+ .start = NR_IRQS_LEGACY + AT91SAM9G45_ID_LCDC,
+ .end = NR_IRQS_LEGACY + AT91SAM9G45_ID_LCDC,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9G45_ID_TCB,
- .end = AT91SAM9G45_ID_TCB,
+ .start = NR_IRQS_LEGACY + AT91SAM9G45_ID_TCB,
+ .end = NR_IRQS_LEGACY + AT91SAM9G45_ID_TCB,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9G45_ID_TCB,
- .end = AT91SAM9G45_ID_TCB,
+ .start = NR_IRQS_LEGACY + AT91SAM9G45_ID_TCB,
+ .end = NR_IRQS_LEGACY + AT91SAM9G45_ID_TCB,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91_ID_SYS,
- .end = AT91_ID_SYS,
+ .start = NR_IRQS_LEGACY + AT91_ID_SYS,
+ .end = NR_IRQS_LEGACY + AT91_ID_SYS,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9G45_ID_TSC,
- .end = AT91SAM9G45_ID_TSC,
+ .start = NR_IRQS_LEGACY + AT91SAM9G45_ID_TSC,
+ .end = NR_IRQS_LEGACY + AT91SAM9G45_ID_TSC,
.flags = IORESOURCE_IRQ,
}
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9G45_ID_TSC,
- .end = AT91SAM9G45_ID_TSC,
+ .start = NR_IRQS_LEGACY + AT91SAM9G45_ID_TSC,
+ .end = NR_IRQS_LEGACY + AT91SAM9G45_ID_TSC,
.flags = IORESOURCE_IRQ,
}
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9G45_ID_PWMC,
- .end = AT91SAM9G45_ID_PWMC,
+ .start = NR_IRQS_LEGACY + AT91SAM9G45_ID_PWMC,
+ .end = NR_IRQS_LEGACY + AT91SAM9G45_ID_PWMC,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9G45_ID_SSC0,
- .end = AT91SAM9G45_ID_SSC0,
+ .start = NR_IRQS_LEGACY + AT91SAM9G45_ID_SSC0,
+ .end = NR_IRQS_LEGACY + AT91SAM9G45_ID_SSC0,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9G45_ID_SSC1,
- .end = AT91SAM9G45_ID_SSC1,
+ .start = NR_IRQS_LEGACY + AT91SAM9G45_ID_SSC1,
+ .end = NR_IRQS_LEGACY + AT91SAM9G45_ID_SSC1,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91_ID_SYS,
- .end = AT91_ID_SYS,
+ .start = NR_IRQS_LEGACY + AT91_ID_SYS,
+ .end = NR_IRQS_LEGACY + AT91_ID_SYS,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9G45_ID_US0,
- .end = AT91SAM9G45_ID_US0,
+ .start = NR_IRQS_LEGACY + AT91SAM9G45_ID_US0,
+ .end = NR_IRQS_LEGACY + AT91SAM9G45_ID_US0,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9G45_ID_US1,
- .end = AT91SAM9G45_ID_US1,
+ .start = NR_IRQS_LEGACY + AT91SAM9G45_ID_US1,
+ .end = NR_IRQS_LEGACY + AT91SAM9G45_ID_US1,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9G45_ID_US2,
- .end = AT91SAM9G45_ID_US2,
+ .start = NR_IRQS_LEGACY + AT91SAM9G45_ID_US2,
+ .end = NR_IRQS_LEGACY + AT91SAM9G45_ID_US2,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9G45_ID_US3,
- .end = AT91SAM9G45_ID_US3,
+ .start = NR_IRQS_LEGACY + AT91SAM9G45_ID_US3,
+ .end = NR_IRQS_LEGACY + AT91SAM9G45_ID_US3,
.flags = IORESOURCE_IRQ,
},
};
#include <mach/cpu.h>
#include <mach/at91_dbgu.h>
#include <mach/at91sam9rl.h>
+#include <mach/at91_aic.h>
#include <mach/at91_pmc.h>
#include <mach/at91_rstc.h>
.flags = IORESOURCE_MEM,
},
[2] = {
- .start = AT91SAM9RL_ID_DMA,
- .end = AT91SAM9RL_ID_DMA,
+ .start = NR_IRQS_LEGACY + AT91SAM9RL_ID_DMA,
+ .end = NR_IRQS_LEGACY + AT91SAM9RL_ID_DMA,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[2] = {
- .start = AT91SAM9RL_ID_UDPHS,
- .end = AT91SAM9RL_ID_UDPHS,
+ .start = NR_IRQS_LEGACY + AT91SAM9RL_ID_UDPHS,
+ .end = NR_IRQS_LEGACY + AT91SAM9RL_ID_UDPHS,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9RL_ID_MCI,
- .end = AT91SAM9RL_ID_MCI,
+ .start = NR_IRQS_LEGACY + AT91SAM9RL_ID_MCI,
+ .end = NR_IRQS_LEGACY + AT91SAM9RL_ID_MCI,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9RL_ID_TWI0,
- .end = AT91SAM9RL_ID_TWI0,
+ .start = NR_IRQS_LEGACY + AT91SAM9RL_ID_TWI0,
+ .end = NR_IRQS_LEGACY + AT91SAM9RL_ID_TWI0,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9RL_ID_SPI,
- .end = AT91SAM9RL_ID_SPI,
+ .start = NR_IRQS_LEGACY + AT91SAM9RL_ID_SPI,
+ .end = NR_IRQS_LEGACY + AT91SAM9RL_ID_SPI,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9RL_ID_AC97C,
- .end = AT91SAM9RL_ID_AC97C,
+ .start = NR_IRQS_LEGACY + AT91SAM9RL_ID_AC97C,
+ .end = NR_IRQS_LEGACY + AT91SAM9RL_ID_AC97C,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9RL_ID_LCDC,
- .end = AT91SAM9RL_ID_LCDC,
+ .start = NR_IRQS_LEGACY + AT91SAM9RL_ID_LCDC,
+ .end = NR_IRQS_LEGACY + AT91SAM9RL_ID_LCDC,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9RL_ID_TC0,
- .end = AT91SAM9RL_ID_TC0,
+ .start = NR_IRQS_LEGACY + AT91SAM9RL_ID_TC0,
+ .end = NR_IRQS_LEGACY + AT91SAM9RL_ID_TC0,
.flags = IORESOURCE_IRQ,
},
[2] = {
- .start = AT91SAM9RL_ID_TC1,
- .end = AT91SAM9RL_ID_TC1,
+ .start = NR_IRQS_LEGACY + AT91SAM9RL_ID_TC1,
+ .end = NR_IRQS_LEGACY + AT91SAM9RL_ID_TC1,
.flags = IORESOURCE_IRQ,
},
[3] = {
- .start = AT91SAM9RL_ID_TC2,
- .end = AT91SAM9RL_ID_TC2,
+ .start = NR_IRQS_LEGACY + AT91SAM9RL_ID_TC2,
+ .end = NR_IRQS_LEGACY + AT91SAM9RL_ID_TC2,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9RL_ID_TSC,
- .end = AT91SAM9RL_ID_TSC,
+ .start = NR_IRQS_LEGACY + AT91SAM9RL_ID_TSC,
+ .end = NR_IRQS_LEGACY + AT91SAM9RL_ID_TSC,
.flags = IORESOURCE_IRQ,
}
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9RL_ID_PWMC,
- .end = AT91SAM9RL_ID_PWMC,
+ .start = NR_IRQS_LEGACY + AT91SAM9RL_ID_PWMC,
+ .end = NR_IRQS_LEGACY + AT91SAM9RL_ID_PWMC,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9RL_ID_SSC0,
- .end = AT91SAM9RL_ID_SSC0,
+ .start = NR_IRQS_LEGACY + AT91SAM9RL_ID_SSC0,
+ .end = NR_IRQS_LEGACY + AT91SAM9RL_ID_SSC0,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9RL_ID_SSC1,
- .end = AT91SAM9RL_ID_SSC1,
+ .start = NR_IRQS_LEGACY + AT91SAM9RL_ID_SSC1,
+ .end = NR_IRQS_LEGACY + AT91SAM9RL_ID_SSC1,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91_ID_SYS,
- .end = AT91_ID_SYS,
+ .start = NR_IRQS_LEGACY + AT91_ID_SYS,
+ .end = NR_IRQS_LEGACY + AT91_ID_SYS,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9RL_ID_US0,
- .end = AT91SAM9RL_ID_US0,
+ .start = NR_IRQS_LEGACY + AT91SAM9RL_ID_US0,
+ .end = NR_IRQS_LEGACY + AT91SAM9RL_ID_US0,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9RL_ID_US1,
- .end = AT91SAM9RL_ID_US1,
+ .start = NR_IRQS_LEGACY + AT91SAM9RL_ID_US1,
+ .end = NR_IRQS_LEGACY + AT91SAM9RL_ID_US1,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9RL_ID_US2,
- .end = AT91SAM9RL_ID_US2,
+ .start = NR_IRQS_LEGACY + AT91SAM9RL_ID_US2,
+ .end = NR_IRQS_LEGACY + AT91SAM9RL_ID_US2,
.flags = IORESOURCE_IRQ,
},
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AT91SAM9RL_ID_US3,
- .end = AT91SAM9RL_ID_US3,
+ .start = NR_IRQS_LEGACY + AT91SAM9RL_ID_US3,
+ .end = NR_IRQS_LEGACY + AT91SAM9RL_ID_US3,
.flags = IORESOURCE_IRQ,
},
};
void __init at91sam9x5_initialize(void)
{
- at91_extern_irq = (1 << AT91SAM9X5_ID_IRQ0);
-
/* Register GPIO subsystem (using DT) */
at91_gpio_init(NULL, 0);
}
/* --------------------------------------------------------------------
* Interrupt initialization
* -------------------------------------------------------------------- */
-/*
- * The default interrupt priority levels (0 = lowest, 7 = highest).
- */
-static unsigned int at91sam9x5_default_irq_priority[NR_AIC_IRQS] __initdata = {
- 7, /* Advanced Interrupt Controller (FIQ) */
- 7, /* System Peripherals */
- 1, /* Parallel IO Controller A and B */
- 1, /* Parallel IO Controller C and D */
- 4, /* Soft Modem */
- 5, /* USART 0 */
- 5, /* USART 1 */
- 5, /* USART 2 */
- 5, /* USART 3 */
- 6, /* Two-Wire Interface 0 */
- 6, /* Two-Wire Interface 1 */
- 6, /* Two-Wire Interface 2 */
- 0, /* Multimedia Card Interface 0 */
- 5, /* Serial Peripheral Interface 0 */
- 5, /* Serial Peripheral Interface 1 */
- 5, /* UART 0 */
- 5, /* UART 1 */
- 0, /* Timer Counter 0, 1, 2, 3, 4 and 5 */
- 0, /* Pulse Width Modulation Controller */
- 0, /* ADC Controller */
- 0, /* DMA Controller 0 */
- 0, /* DMA Controller 1 */
- 2, /* USB Host High Speed port */
- 2, /* USB Device High speed port */
- 3, /* Ethernet MAC 0 */
- 3, /* LDC Controller or Image Sensor Interface */
- 0, /* Multimedia Card Interface 1 */
- 3, /* Ethernet MAC 1 */
- 4, /* Synchronous Serial Interface */
- 4, /* CAN Controller 0 */
- 4, /* CAN Controller 1 */
- 0, /* Advanced Interrupt Controller (IRQ0) */
-};
struct at91_init_soc __initdata at91sam9x5_soc = {
.map_io = at91sam9x5_map_io,
- .default_irq_priority = at91sam9x5_default_irq_priority,
.register_clocks = at91sam9x5_register_clocks,
.init = at91sam9x5_initialize,
};
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/irq.h>
+#include <linux/io.h>
#include <asm/proc-fns.h>
#include <asm/system_misc.h>
#include <asm/mach/arch.h>
#include <mach/at91x40.h>
+#include <mach/at91_aic.h>
#include <mach/at91_st.h>
#include <mach/timex.h>
#include "generic.h"
#include <mach/board.h>
#include <mach/cpu.h>
+#include <mach/at91_aic.h>
#include "generic.h"
/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
.timer = &at91rm9200_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = onearm_init_early,
.init_irq = at91_init_irq_default,
.init_machine = onearm_board_init,
#include <asm/mach/irq.h>
#include <mach/board.h>
+#include <mach/at91_aic.h>
#include "generic.h"
/* Maintainer: Sergey Lapin <slapin@ossfans.org> */
.timer = &at91sam926x_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = afeb9260_init_early,
.init_irq = at91_init_irq_default,
.init_machine = afeb9260_board_init,
#include <asm/mach/irq.h>
#include <mach/board.h>
+#include <mach/at91_aic.h>
#include <mach/at91sam9_smc.h>
#include "sam9_smc.h"
/* Maintainer: KwikByte */
.timer = &at91sam926x_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = cam60_init_early,
.init_irq = at91_init_irq_default,
.init_machine = cam60_board_init,
#include <mach/hardware.h>
#include <mach/board.h>
+#include <mach/at91_aic.h>
#include "generic.h"
/* Maintainer: Conitec Datasystems */
.timer = &at91rm9200_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = carmeva_init_early,
.init_irq = at91_init_irq_default,
.init_machine = carmeva_board_init,
#include <mach/hardware.h>
#include <mach/board.h>
+#include <mach/at91_aic.h>
#include <mach/at91sam9_smc.h>
#include <mach/at91sam9260_matrix.h>
#include <mach/at91_matrix.h>
/* Maintainer: Eric Benard - EUKREA Electromatique */
.timer = &at91sam926x_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = cpu9krea_init_early,
.init_irq = at91_init_irq_default,
.init_machine = cpu9krea_board_init,
#include <asm/mach/irq.h>
#include <mach/board.h>
+#include <mach/at91_aic.h>
#include <mach/at91rm9200_mc.h>
#include <mach/at91_ramc.h>
#include <mach/cpu.h>
/* Maintainer: Eric Benard - EUKREA Electromatique */
.timer = &at91rm9200_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = cpuat91_init_early,
.init_irq = at91_init_irq_default,
.init_machine = cpuat91_board_init,
#include <mach/hardware.h>
#include <mach/board.h>
+#include <mach/at91_aic.h>
#include "generic.h"
/* Maintainer: Bill Gatliff */
.timer = &at91rm9200_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = csb337_init_early,
.init_irq = at91_init_irq_default,
.init_machine = csb337_board_init,
#include <mach/hardware.h>
#include <mach/board.h>
+#include <mach/at91_aic.h>
#include "generic.h"
/* Maintainer: Bill Gatliff */
.timer = &at91rm9200_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = csb637_init_early,
.init_irq = at91_init_irq_default,
.init_machine = csb637_board_init,
#include <linux/of_platform.h>
#include <mach/board.h>
+#include <mach/at91_aic.h>
#include <asm/setup.h>
#include <asm/irq.h>
/* Maintainer: Atmel */
.timer = &at91sam926x_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = at91_dt_initialize,
.init_irq = at91_dt_init_irq,
.init_machine = at91_dt_device_init,
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <mach/board.h>
+#include <mach/at91_aic.h>
#include "generic.h"
static void __init at91eb01_init_irq(void)
MACHINE_START(AT91EB01, "Atmel AT91 EB01")
/* Maintainer: Greg Ungerer <gerg@snapgear.com> */
.timer = &at91x40_timer,
+ .handle_irq = at91_aic_handle_irq,
.init_early = at91eb01_init_early,
.init_irq = at91eb01_init_irq,
MACHINE_END
#include <asm/mach/irq.h>
#include <mach/board.h>
+#include <mach/at91_aic.h>
#include "generic.h"
MACHINE_START(ATEB9200, "Embest ATEB9200")
.timer = &at91rm9200_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = eb9200_init_early,
.init_irq = at91_init_irq_default,
.init_machine = eb9200_board_init,
#include <mach/board.h>
#include <mach/cpu.h>
+#include <mach/at91_aic.h>
#include "generic.h"
/* Maintainer: emQbit.com */
.timer = &at91rm9200_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = ecb_at91init_early,
.init_irq = at91_init_irq_default,
.init_machine = ecb_at91board_init,
#include <asm/mach/map.h>
#include <mach/board.h>
+#include <mach/at91_aic.h>
#include <mach/at91rm9200_mc.h>
#include <mach/at91_ramc.h>
#include <mach/cpu.h>
/* Maintainer: Sascha Hauer */
.timer = &at91rm9200_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = eco920_init_early,
.init_irq = at91_init_irq_default,
.init_machine = eco920_board_init,
#include <mach/hardware.h>
#include <mach/board.h>
+#include <mach/at91_aic.h>
#include "generic.h"
/* Maintainer: Maxim Osipov */
.timer = &at91sam926x_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = flexibity_init_early,
.init_irq = at91_init_irq_default,
.init_machine = flexibity_board_init,
#include <asm/mach/irq.h>
#include <mach/board.h>
+#include <mach/at91_aic.h>
#include <mach/at91sam9_smc.h>
#include "sam9_smc.h"
/* Maintainer: Sergio Tanzilli */
.timer = &at91sam926x_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = foxg20_init_early,
.init_irq = at91_init_irq_default,
.init_machine = foxg20_board_init,
#include <asm/mach/arch.h>
#include <mach/board.h>
+#include <mach/at91_aic.h>
#include <mach/at91sam9_smc.h>
#include <mach/gsia18s.h>
#include <mach/stamp9g20.h>
MACHINE_START(GSIA18S, "GS_IA18_S")
.timer = &at91sam926x_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = gsia18s_init_early,
.init_irq = at91_init_irq_default,
.init_machine = gsia18s_board_init,
#include <asm/mach/irq.h>
#include <mach/board.h>
+#include <mach/at91_aic.h>
#include <mach/cpu.h>
#include "generic.h"
/* Maintainer: Sergei Sharonov */
.timer = &at91rm9200_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = kafa_init_early,
.init_irq = at91_init_irq_default,
.init_machine = kafa_board_init,
#include <mach/board.h>
#include <mach/cpu.h>
+#include <mach/at91_aic.h>
#include <mach/at91rm9200_mc.h>
#include <mach/at91_ramc.h>
/* Maintainer: KwikByte, Inc. */
.timer = &at91rm9200_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = kb9202_init_early,
.init_irq = at91_init_irq_default,
.init_machine = kb9202_board_init,
#include <mach/hardware.h>
#include <mach/board.h>
+#include <mach/at91_aic.h>
#include <mach/at91sam9_smc.h>
#include "sam9_smc.h"
/* Maintainer: ADENEO */
.timer = &at91sam926x_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = neocore926_init_early,
.init_irq = at91_init_irq_default,
.init_machine = neocore926_board_init,
#include <asm/mach/arch.h>
#include <mach/board.h>
+#include <mach/at91_aic.h>
#include <mach/at91sam9_smc.h>
#include <mach/stamp9g20.h>
/* Maintainer: pgsellmann@portner-elektronik.at */
.timer = &at91sam926x_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = pcontrol_g20_init_early,
.init_irq = at91_init_irq_default,
.init_machine = pcontrol_g20_board_init,
#include <asm/mach/irq.h>
#include <mach/board.h>
+#include <mach/at91_aic.h>
#include <mach/at91rm9200_mc.h>
#include <mach/at91_ramc.h>
/* Maintainer: Kleinhenz Elektronik GmbH */
.timer = &at91rm9200_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = picotux200_init_early,
.init_irq = at91_init_irq_default,
.init_machine = picotux200_board_init,
#include <mach/hardware.h>
#include <mach/board.h>
+#include <mach/at91_aic.h>
#include <mach/at91sam9_smc.h>
#include <mach/at91_shdwc.h>
/* Maintainer: calao-systems */
.timer = &at91sam926x_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = ek_init_early,
.init_irq = at91_init_irq_default,
.init_machine = ek_board_init,
#include <mach/hardware.h>
#include <mach/board.h>
+#include <mach/at91_aic.h>
#include <mach/at91rm9200_mc.h>
#include <mach/at91_ramc.h>
/* Maintainer: SAN People/Atmel */
.timer = &at91rm9200_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = dk_init_early,
.init_irq = at91_init_irq_default,
.init_machine = dk_board_init,
#include <mach/hardware.h>
#include <mach/board.h>
+#include <mach/at91_aic.h>
#include <mach/at91rm9200_mc.h>
#include <mach/at91_ramc.h>
/* Maintainer: SAN People/Atmel */
.timer = &at91rm9200_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = ek_init_early,
.init_irq = at91_init_irq_default,
.init_machine = ek_board_init,
#include <mach/hardware.h>
#include <mach/board.h>
+#include <mach/at91_aic.h>
#include <linux/gpio.h>
/* Maintainer: Josef Holzmayr <holzmayr@rsi-elektrotechnik.de> */
.timer = &at91rm9200_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = rsi_ews_init_early,
.init_irq = at91_init_irq_default,
.init_machine = rsi_ews_board_init,
#include <asm/mach/irq.h>
#include <mach/board.h>
+#include <mach/at91_aic.h>
#include <mach/at91sam9_smc.h>
#include "sam9_smc.h"
/* Maintainer: Olimex */
.timer = &at91sam926x_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = ek_init_early,
.init_irq = at91_init_irq_default,
.init_machine = ek_board_init,
#include <mach/hardware.h>
#include <mach/board.h>
+#include <mach/at91_aic.h>
#include <mach/at91sam9_smc.h>
#include <mach/at91_shdwc.h>
#include <mach/system_rev.h>
/* Maintainer: Atmel */
.timer = &at91sam926x_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = ek_init_early,
.init_irq = at91_init_irq_default,
.init_machine = ek_board_init,
#include <mach/hardware.h>
#include <mach/board.h>
+#include <mach/at91_aic.h>
#include <mach/at91sam9_smc.h>
#include <mach/at91_shdwc.h>
#include <mach/system_rev.h>
/* Maintainer: Atmel */
.timer = &at91sam926x_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = ek_init_early,
.init_irq = at91_init_irq_default,
.init_machine = ek_board_init,
#include <mach/hardware.h>
#include <mach/board.h>
+#include <mach/at91_aic.h>
#include <mach/at91sam9_smc.h>
#include <mach/at91_shdwc.h>
#include <mach/system_rev.h>
/* Maintainer: Atmel */
.timer = &at91sam926x_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = ek_init_early,
.init_irq = at91_init_irq_default,
.init_machine = ek_board_init,
#include <asm/mach/irq.h>
#include <mach/board.h>
+#include <mach/at91_aic.h>
#include <mach/at91sam9_smc.h>
#include <mach/system_rev.h>
/* Maintainer: Atmel */
.timer = &at91sam926x_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = ek_init_early,
.init_irq = at91_init_irq_default,
.init_machine = ek_board_init,
/* Maintainer: Atmel */
.timer = &at91sam926x_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = ek_init_early,
.init_irq = at91_init_irq_default,
.init_machine = ek_board_init,
#include <asm/mach/irq.h>
#include <mach/board.h>
+#include <mach/at91_aic.h>
#include <mach/at91sam9_smc.h>
#include <mach/at91_shdwc.h>
#include <mach/system_rev.h>
/* Maintainer: Atmel */
.timer = &at91sam926x_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = ek_init_early,
.init_irq = at91_init_irq_default,
.init_machine = ek_board_init,
#include <mach/hardware.h>
#include <mach/board.h>
+#include <mach/at91_aic.h>
#include <mach/at91sam9_smc.h>
#include <mach/at91_shdwc.h>
/* Maintainer: Atmel */
.timer = &at91sam926x_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = ek_init_early,
.init_irq = at91_init_irq_default,
.init_machine = ek_board_init,
#include <mach/hardware.h>
#include <mach/board.h>
+#include <mach/at91_aic.h>
#include <mach/at91sam9_smc.h>
#include "sam9_smc.h"
MACHINE_START(SNAPPER_9260, "Bluewater Systems Snapper 9260/9G20 module")
.timer = &at91sam926x_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = snapper9260_init_early,
.init_irq = at91_init_irq_default,
.init_machine = snapper9260_board_init,
#include <asm/mach/arch.h>
#include <mach/board.h>
+#include <mach/at91_aic.h>
#include <mach/at91sam9_smc.h>
#include "sam9_smc.h"
/* Maintainer: taskit GmbH */
.timer = &at91sam926x_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = stamp9g20_init_early,
.init_irq = at91_init_irq_default,
.init_machine = portuxg20_board_init,
/* Maintainer: taskit GmbH */
.timer = &at91sam926x_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = stamp9g20_init_early,
.init_irq = at91_init_irq_default,
.init_machine = stamp9g20evb_board_init,
#include <mach/hardware.h>
#include <mach/board.h>
+#include <mach/at91_aic.h>
#include <mach/at91sam9_smc.h>
#include <mach/at91_shdwc.h>
/* Maintainer: calao-systems */
.timer = &at91sam926x_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = ek_init_early,
.init_irq = at91_init_irq_default,
.init_machine = ek_board_init,
/* Maintainer: calao-systems */
.timer = &at91sam926x_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = ek_init_early,
.init_irq = at91_init_irq_default,
.init_machine = ek_board_init,
/* Maintainer: Jean-Christophe PLAGNIOL-VILLARD */
.timer = &at91sam926x_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = ek_init_early,
.init_irq = at91_init_irq_default,
.init_machine = ek_board_init,
#include <mach/hardware.h>
#include <mach/board.h>
+#include <mach/at91_aic.h>
#include <mach/at91rm9200_mc.h>
#include <mach/at91_ramc.h>
#include <mach/cpu.h>
/* Maintainer: S.Birtles */
.timer = &at91rm9200_timer,
.map_io = at91_map_io,
+ .handle_irq = at91_aic_handle_irq,
.init_early = yl9200_init_early,
.init_irq = at91_init_irq_default,
.init_machine = yl9200_board_init,
extern void __init at91_aic_init(unsigned int priority[]);
extern int __init at91_aic_of_init(struct device_node *node,
struct device_node *parent);
+extern int __init at91_aic5_of_init(struct device_node *node,
+ struct device_node *parent);
/* Timer */
#include <linux/of_irq.h>
#include <linux/of_gpio.h>
+#include <asm/mach/irq.h>
+
#include <mach/hardware.h>
#include <mach/at91_pio.h>
static void gpio_irq_handler(unsigned irq, struct irq_desc *desc)
{
+ struct irq_chip *chip = irq_desc_get_chip(desc);
struct irq_data *idata = irq_desc_get_irq_data(desc);
- struct irq_chip *chip = irq_data_get_irq_chip(idata);
struct at91_gpio_chip *at91_gpio = irq_data_get_irq_chip_data(idata);
void __iomem *pio = at91_gpio->regbase;
unsigned long isr;
int n;
- /* temporarily mask (level sensitive) parent IRQ */
- chip->irq_ack(idata);
+ chained_irq_enter(chip, desc);
for (;;) {
/* Reading ISR acks pending (edge triggered) GPIO interrupts.
* When there none are pending, we're finished unless we need
n = find_next_bit(&isr, BITS_PER_LONG, n + 1);
}
}
- chip->irq_unmask(idata);
+ chained_irq_exit(chip, desc);
/* now it may re-trigger */
}
__raw_readl(at91_aic_base + field)
#define at91_aic_write(field, value) \
- __raw_writel(value, at91_aic_base + field);
+ __raw_writel(value, at91_aic_base + field)
#else
.extern at91_aic_base
#endif
+/* Number of irq lines managed by AIC */
+#define NR_AIC_IRQS 32
+#define NR_AIC5_IRQS 128
+
+#define AT91_AIC5_SSR 0x0 /* Source Select Register [AIC5] */
+#define AT91_AIC5_INTSEL_MSK (0x7f << 0) /* Interrupt Line Selection Mask */
+
+#define AT91_AIC_IRQ_MIN_PRIORITY 0
+#define AT91_AIC_IRQ_MAX_PRIORITY 7
+
#define AT91_AIC_SMR(n) ((n) * 4) /* Source Mode Registers 0-31 */
+#define AT91_AIC5_SMR 0x4 /* Source Mode Register [AIC5] */
#define AT91_AIC_PRIOR (7 << 0) /* Priority Level */
#define AT91_AIC_SRCTYPE (3 << 5) /* Interrupt Source Type */
#define AT91_AIC_SRCTYPE_LOW (0 << 5)
#define AT91_AIC_SRCTYPE_RISING (3 << 5)
#define AT91_AIC_SVR(n) (0x80 + ((n) * 4)) /* Source Vector Registers 0-31 */
+#define AT91_AIC5_SVR 0x8 /* Source Vector Register [AIC5] */
#define AT91_AIC_IVR 0x100 /* Interrupt Vector Register */
+#define AT91_AIC5_IVR 0x10 /* Interrupt Vector Register [AIC5] */
#define AT91_AIC_FVR 0x104 /* Fast Interrupt Vector Register */
+#define AT91_AIC5_FVR 0x14 /* Fast Interrupt Vector Register [AIC5] */
#define AT91_AIC_ISR 0x108 /* Interrupt Status Register */
+#define AT91_AIC5_ISR 0x18 /* Interrupt Status Register [AIC5] */
#define AT91_AIC_IRQID (0x1f << 0) /* Current Interrupt Identifier */
#define AT91_AIC_IPR 0x10c /* Interrupt Pending Register */
+#define AT91_AIC5_IPR0 0x20 /* Interrupt Pending Register 0 [AIC5] */
+#define AT91_AIC5_IPR1 0x24 /* Interrupt Pending Register 1 [AIC5] */
+#define AT91_AIC5_IPR2 0x28 /* Interrupt Pending Register 2 [AIC5] */
+#define AT91_AIC5_IPR3 0x2c /* Interrupt Pending Register 3 [AIC5] */
#define AT91_AIC_IMR 0x110 /* Interrupt Mask Register */
+#define AT91_AIC5_IMR 0x30 /* Interrupt Mask Register [AIC5] */
#define AT91_AIC_CISR 0x114 /* Core Interrupt Status Register */
+#define AT91_AIC5_CISR 0x34 /* Core Interrupt Status Register [AIC5] */
#define AT91_AIC_NFIQ (1 << 0) /* nFIQ Status */
#define AT91_AIC_NIRQ (1 << 1) /* nIRQ Status */
#define AT91_AIC_IECR 0x120 /* Interrupt Enable Command Register */
+#define AT91_AIC5_IECR 0x40 /* Interrupt Enable Command Register [AIC5] */
#define AT91_AIC_IDCR 0x124 /* Interrupt Disable Command Register */
+#define AT91_AIC5_IDCR 0x44 /* Interrupt Disable Command Register [AIC5] */
#define AT91_AIC_ICCR 0x128 /* Interrupt Clear Command Register */
+#define AT91_AIC5_ICCR 0x48 /* Interrupt Clear Command Register [AIC5] */
#define AT91_AIC_ISCR 0x12c /* Interrupt Set Command Register */
+#define AT91_AIC5_ISCR 0x4c /* Interrupt Set Command Register [AIC5] */
#define AT91_AIC_EOICR 0x130 /* End of Interrupt Command Register */
+#define AT91_AIC5_EOICR 0x38 /* End of Interrupt Command Register [AIC5] */
#define AT91_AIC_SPU 0x134 /* Spurious Interrupt Vector Register */
+#define AT91_AIC5_SPU 0x3c /* Spurious Interrupt Vector Register [AIC5] */
#define AT91_AIC_DCR 0x138 /* Debug Control Register */
+#define AT91_AIC5_DCR 0x6c /* Debug Control Register [AIC5] */
#define AT91_AIC_DCR_PROT (1 << 0) /* Protection Mode */
#define AT91_AIC_DCR_GMSK (1 << 1) /* General Mask */
#define AT91_AIC_FFER 0x140 /* Fast Forcing Enable Register [SAM9 only] */
+#define AT91_AIC5_FFER 0x50 /* Fast Forcing Enable Register [AIC5] */
#define AT91_AIC_FFDR 0x144 /* Fast Forcing Disable Register [SAM9 only] */
+#define AT91_AIC5_FFDR 0x54 /* Fast Forcing Disable Register [AIC5] */
#define AT91_AIC_FFSR 0x148 /* Fast Forcing Status Register [SAM9 only] */
+#define AT91_AIC5_FFSR 0x58 /* Fast Forcing Status Register [AIC5] */
+
+void at91_aic_handle_irq(struct pt_regs *regs);
+void at91_aic5_handle_irq(struct pt_regs *regs);
#endif
+++ /dev/null
-/*
- * arch/arm/mach-at91/include/mach/at91_spi.h
- *
- * Copyright (C) 2005 Ivan Kokshaysky
- * Copyright (C) SAN People
- *
- * Serial Peripheral Interface (SPI) registers.
- * Based on AT91RM9200 datasheet revision E.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#ifndef AT91_SPI_H
-#define AT91_SPI_H
-
-#define AT91_SPI_CR 0x00 /* Control Register */
-#define AT91_SPI_SPIEN (1 << 0) /* SPI Enable */
-#define AT91_SPI_SPIDIS (1 << 1) /* SPI Disable */
-#define AT91_SPI_SWRST (1 << 7) /* SPI Software Reset */
-#define AT91_SPI_LASTXFER (1 << 24) /* Last Transfer [SAM9261 only] */
-
-#define AT91_SPI_MR 0x04 /* Mode Register */
-#define AT91_SPI_MSTR (1 << 0) /* Master/Slave Mode */
-#define AT91_SPI_PS (1 << 1) /* Peripheral Select */
-#define AT91_SPI_PS_FIXED (0 << 1)
-#define AT91_SPI_PS_VARIABLE (1 << 1)
-#define AT91_SPI_PCSDEC (1 << 2) /* Chip Select Decode */
-#define AT91_SPI_DIV32 (1 << 3) /* Clock Selection [AT91RM9200 only] */
-#define AT91_SPI_MODFDIS (1 << 4) /* Mode Fault Detection */
-#define AT91_SPI_LLB (1 << 7) /* Local Loopback Enable */
-#define AT91_SPI_PCS (0xf << 16) /* Peripheral Chip Select */
-#define AT91_SPI_DLYBCS (0xff << 24) /* Delay Between Chip Selects */
-
-#define AT91_SPI_RDR 0x08 /* Receive Data Register */
-#define AT91_SPI_RD (0xffff << 0) /* Receive Data */
-#define AT91_SPI_PCS (0xf << 16) /* Peripheral Chip Select */
-
-#define AT91_SPI_TDR 0x0c /* Transmit Data Register */
-#define AT91_SPI_TD (0xffff << 0) /* Transmit Data */
-#define AT91_SPI_PCS (0xf << 16) /* Peripheral Chip Select */
-#define AT91_SPI_LASTXFER (1 << 24) /* Last Transfer [SAM9261 only] */
-
-#define AT91_SPI_SR 0x10 /* Status Register */
-#define AT91_SPI_RDRF (1 << 0) /* Receive Data Register Full */
-#define AT91_SPI_TDRE (1 << 1) /* Transmit Data Register Full */
-#define AT91_SPI_MODF (1 << 2) /* Mode Fault Error */
-#define AT91_SPI_OVRES (1 << 3) /* Overrun Error Status */
-#define AT91_SPI_ENDRX (1 << 4) /* End of RX buffer */
-#define AT91_SPI_ENDTX (1 << 5) /* End of TX buffer */
-#define AT91_SPI_RXBUFF (1 << 6) /* RX Buffer Full */
-#define AT91_SPI_TXBUFE (1 << 7) /* TX Buffer Empty */
-#define AT91_SPI_NSSR (1 << 8) /* NSS Rising [SAM9261 only] */
-#define AT91_SPI_TXEMPTY (1 << 9) /* Transmission Register Empty [SAM9261 only] */
-#define AT91_SPI_SPIENS (1 << 16) /* SPI Enable Status */
-
-#define AT91_SPI_IER 0x14 /* Interrupt Enable Register */
-#define AT91_SPI_IDR 0x18 /* Interrupt Disable Register */
-#define AT91_SPI_IMR 0x1c /* Interrupt Mask Register */
-
-#define AT91_SPI_CSR(n) (0x30 + ((n) * 4)) /* Chip Select Registers 0-3 */
-#define AT91_SPI_CPOL (1 << 0) /* Clock Polarity */
-#define AT91_SPI_NCPHA (1 << 1) /* Clock Phase */
-#define AT91_SPI_CSAAT (1 << 3) /* Chip Select Active After Transfer [SAM9261 only] */
-#define AT91_SPI_BITS (0xf << 4) /* Bits Per Transfer */
-#define AT91_SPI_BITS_8 (0 << 4)
-#define AT91_SPI_BITS_9 (1 << 4)
-#define AT91_SPI_BITS_10 (2 << 4)
-#define AT91_SPI_BITS_11 (3 << 4)
-#define AT91_SPI_BITS_12 (4 << 4)
-#define AT91_SPI_BITS_13 (5 << 4)
-#define AT91_SPI_BITS_14 (6 << 4)
-#define AT91_SPI_BITS_15 (7 << 4)
-#define AT91_SPI_BITS_16 (8 << 4)
-#define AT91_SPI_SCBR (0xff << 8) /* Serial Clock Baud Rate */
-#define AT91_SPI_DLYBS (0xff << 16) /* Delay before SPCK */
-#define AT91_SPI_DLYBCT (0xff << 24) /* Delay between Consecutive Transfers */
-
-#endif
+++ /dev/null
-/*
- * arch/arm/mach-at91/include/mach/at91_ssc.h
- *
- * Copyright (C) SAN People
- *
- * Serial Synchronous Controller (SSC) registers.
- * Based on AT91RM9200 datasheet revision E.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#ifndef AT91_SSC_H
-#define AT91_SSC_H
-
-#define AT91_SSC_CR 0x00 /* Control Register */
-#define AT91_SSC_RXEN (1 << 0) /* Receive Enable */
-#define AT91_SSC_RXDIS (1 << 1) /* Receive Disable */
-#define AT91_SSC_TXEN (1 << 8) /* Transmit Enable */
-#define AT91_SSC_TXDIS (1 << 9) /* Transmit Disable */
-#define AT91_SSC_SWRST (1 << 15) /* Software Reset */
-
-#define AT91_SSC_CMR 0x04 /* Clock Mode Register */
-#define AT91_SSC_CMR_DIV (0xfff << 0) /* Clock Divider */
-
-#define AT91_SSC_RCMR 0x10 /* Receive Clock Mode Register */
-#define AT91_SSC_CKS (3 << 0) /* Clock Selection */
-#define AT91_SSC_CKS_DIV (0 << 0)
-#define AT91_SSC_CKS_CLOCK (1 << 0)
-#define AT91_SSC_CKS_PIN (2 << 0)
-#define AT91_SSC_CKO (7 << 2) /* Clock Output Mode Selection */
-#define AT91_SSC_CKO_NONE (0 << 2)
-#define AT91_SSC_CKO_CONTINUOUS (1 << 2)
-#define AT91_SSC_CKI (1 << 5) /* Clock Inversion */
-#define AT91_SSC_CKI_FALLING (0 << 5)
-#define AT91_SSC_CK_RISING (1 << 5)
-#define AT91_SSC_CKG (1 << 6) /* Receive Clock Gating Selection [AT91SAM9261 only] */
-#define AT91_SSC_CKG_NONE (0 << 6)
-#define AT91_SSC_CKG_RFLOW (1 << 6)
-#define AT91_SSC_CKG_RFHIGH (2 << 6)
-#define AT91_SSC_START (0xf << 8) /* Start Selection */
-#define AT91_SSC_START_CONTINUOUS (0 << 8)
-#define AT91_SSC_START_TX_RX (1 << 8)
-#define AT91_SSC_START_LOW_RF (2 << 8)
-#define AT91_SSC_START_HIGH_RF (3 << 8)
-#define AT91_SSC_START_FALLING_RF (4 << 8)
-#define AT91_SSC_START_RISING_RF (5 << 8)
-#define AT91_SSC_START_LEVEL_RF (6 << 8)
-#define AT91_SSC_START_EDGE_RF (7 << 8)
-#define AT91_SSC_STOP (1 << 12) /* Receive Stop Selection [AT91SAM9261 only] */
-#define AT91_SSC_STTDLY (0xff << 16) /* Start Delay */
-#define AT91_SSC_PERIOD (0xff << 24) /* Period Divider Selection */
-
-#define AT91_SSC_RFMR 0x14 /* Receive Frame Mode Register */
-#define AT91_SSC_DATALEN (0x1f << 0) /* Data Length */
-#define AT91_SSC_LOOP (1 << 5) /* Loop Mode */
-#define AT91_SSC_MSBF (1 << 7) /* Most Significant Bit First */
-#define AT91_SSC_DATNB (0xf << 8) /* Data Number per Frame */
-#define AT91_SSC_FSLEN (0xf << 16) /* Frame Sync Length */
-#define AT91_SSC_FSOS (7 << 20) /* Frame Sync Output Selection */
-#define AT91_SSC_FSOS_NONE (0 << 20)
-#define AT91_SSC_FSOS_NEGATIVE (1 << 20)
-#define AT91_SSC_FSOS_POSITIVE (2 << 20)
-#define AT91_SSC_FSOS_LOW (3 << 20)
-#define AT91_SSC_FSOS_HIGH (4 << 20)
-#define AT91_SSC_FSOS_TOGGLE (5 << 20)
-#define AT91_SSC_FSEDGE (1 << 24) /* Frame Sync Edge Detection */
-#define AT91_SSC_FSEDGE_POSITIVE (0 << 24)
-#define AT91_SSC_FSEDGE_NEGATIVE (1 << 24)
-
-#define AT91_SSC_TCMR 0x18 /* Transmit Clock Mode Register */
-#define AT91_SSC_TFMR 0x1c /* Transmit Fram Mode Register */
-#define AT91_SSC_DATDEF (1 << 5) /* Data Default Value */
-#define AT91_SSC_FSDEN (1 << 23) /* Frame Sync Data Enable */
-
-#define AT91_SSC_RHR 0x20 /* Receive Holding Register */
-#define AT91_SSC_THR 0x24 /* Transmit Holding Register */
-#define AT91_SSC_RSHR 0x30 /* Receive Sync Holding Register */
-#define AT91_SSC_TSHR 0x34 /* Transmit Sync Holding Register */
-
-#define AT91_SSC_RC0R 0x38 /* Receive Compare 0 Register [AT91SAM9261 only] */
-#define AT91_SSC_RC1R 0x3c /* Receive Compare 1 Register [AT91SAM9261 only] */
-
-#define AT91_SSC_SR 0x40 /* Status Register */
-#define AT91_SSC_TXRDY (1 << 0) /* Transmit Ready */
-#define AT91_SSC_TXEMPTY (1 << 1) /* Transmit Empty */
-#define AT91_SSC_ENDTX (1 << 2) /* End of Transmission */
-#define AT91_SSC_TXBUFE (1 << 3) /* Transmit Buffer Empty */
-#define AT91_SSC_RXRDY (1 << 4) /* Receive Ready */
-#define AT91_SSC_OVRUN (1 << 5) /* Receive Overrun */
-#define AT91_SSC_ENDRX (1 << 6) /* End of Reception */
-#define AT91_SSC_RXBUFF (1 << 7) /* Receive Buffer Full */
-#define AT91_SSC_CP0 (1 << 8) /* Compare 0 [AT91SAM9261 only] */
-#define AT91_SSC_CP1 (1 << 9) /* Compare 1 [AT91SAM9261 only] */
-#define AT91_SSC_TXSYN (1 << 10) /* Transmit Sync */
-#define AT91_SSC_RXSYN (1 << 11) /* Receive Sync */
-#define AT91_SSC_TXENA (1 << 16) /* Transmit Enable */
-#define AT91_SSC_RXENA (1 << 17) /* Receive Enable */
-
-#define AT91_SSC_IER 0x44 /* Interrupt Enable Register */
-#define AT91_SSC_IDR 0x48 /* Interrupt Disable Register */
-#define AT91_SSC_IMR 0x4c /* Interrupt Mask Register */
-
-#endif
+++ /dev/null
-/*
- * arch/arm/mach-at91/include/mach/entry-macro.S
- *
- * Copyright (C) 2003-2005 SAN People
- *
- * Low-level IRQ helper macros for AT91RM9200 platforms
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <mach/hardware.h>
-#include <mach/at91_aic.h>
-
- .macro get_irqnr_preamble, base, tmp
- ldr \base, =at91_aic_base @ base virtual address of AIC peripheral
- ldr \base, [\base]
- .endm
-
- .macro get_irqnr_and_base, irqnr, irqstat, base, tmp
- ldr \irqnr, [\base, #AT91_AIC_IVR] @ read IRQ vector register: de-asserts nIRQ to processor (and clears interrupt)
- ldr \irqstat, [\base, #AT91_AIC_ISR] @ read interrupt source number
- teq \irqstat, #0 @ ISR is 0 when no current interrupt, or spurious interrupt
- streq \tmp, [\base, #AT91_AIC_EOICR] @ not going to be handled further, then ACK it now.
- .endm
-
+++ /dev/null
-/*
- * arch/arm/mach-at91/include/mach/irqs.h
- *
- * Copyright (C) 2004 SAN People
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-
-#ifndef __ASM_ARCH_IRQS_H
-#define __ASM_ARCH_IRQS_H
-
-#include <linux/io.h>
-#include <mach/at91_aic.h>
-
-#define NR_AIC_IRQS 32
-
-
-/*
- * Acknowledge interrupt with AIC after interrupt has been handled.
- * (by kernel/irq.c)
- */
-#define irq_finish(irq) do { at91_aic_write(AT91_AIC_EOICR, 0); } while (0)
-
-
-/*
- * IRQ interrupt symbols are the AT91xxx_ID_* symbols
- * for IRQs handled directly through the AIC, or else the AT91_PIN_*
- * symbols in gpio.h for ones handled indirectly as GPIOs.
- * We make provision for 5 banks of GPIO.
- */
-#define NR_IRQS (NR_AIC_IRQS + (5 * 32))
-
-/* FIQ is AIC source 0. */
-#define FIQ_START AT91_ID_FIQ
-
-#endif
#include <linux/init.h>
#include <linux/module.h>
#include <linux/mm.h>
+#include <linux/bitmap.h>
#include <linux/types.h>
#include <linux/irq.h>
#include <linux/of.h>
#include <linux/of_irq.h>
#include <linux/irqdomain.h>
#include <linux/err.h>
+#include <linux/slab.h>
#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/setup.h>
+#include <asm/exception.h>
#include <asm/mach/arch.h>
#include <asm/mach/irq.h>
#include <asm/mach/map.h>
+#include <mach/at91_aic.h>
+
void __iomem *at91_aic_base;
static struct irq_domain *at91_aic_domain;
static struct device_node *at91_aic_np;
+static unsigned int n_irqs = NR_AIC_IRQS;
+static unsigned long at91_aic_caps = 0;
+
+/* AIC5 introduces a Source Select Register */
+#define AT91_AIC_CAP_AIC5 (1 << 0)
+#define has_aic5() (at91_aic_caps & AT91_AIC_CAP_AIC5)
+
+#ifdef CONFIG_PM
+
+static unsigned long *wakeups;
+static unsigned long *backups;
+
+#define set_backup(bit) set_bit(bit, backups)
+#define clear_backup(bit) clear_bit(bit, backups)
+
+static int at91_aic_pm_init(void)
+{
+ backups = kzalloc(BITS_TO_LONGS(n_irqs) * sizeof(*backups), GFP_KERNEL);
+ if (!backups)
+ return -ENOMEM;
+
+ wakeups = kzalloc(BITS_TO_LONGS(n_irqs) * sizeof(*backups), GFP_KERNEL);
+ if (!wakeups) {
+ kfree(backups);
+ return -ENOMEM;
+ }
+
+ return 0;
+}
+
+static int at91_aic_set_wake(struct irq_data *d, unsigned value)
+{
+ if (unlikely(d->hwirq >= n_irqs))
+ return -EINVAL;
+
+ if (value)
+ set_bit(d->hwirq, wakeups);
+ else
+ clear_bit(d->hwirq, wakeups);
+
+ return 0;
+}
+
+void at91_irq_suspend(void)
+{
+ int i = 0, bit;
+
+ if (has_aic5()) {
+ /* disable enabled irqs */
+ while ((bit = find_next_bit(backups, n_irqs, i)) < n_irqs) {
+ at91_aic_write(AT91_AIC5_SSR,
+ bit & AT91_AIC5_INTSEL_MSK);
+ at91_aic_write(AT91_AIC5_IDCR, 1);
+ i = bit;
+ }
+ /* enable wakeup irqs */
+ i = 0;
+ while ((bit = find_next_bit(wakeups, n_irqs, i)) < n_irqs) {
+ at91_aic_write(AT91_AIC5_SSR,
+ bit & AT91_AIC5_INTSEL_MSK);
+ at91_aic_write(AT91_AIC5_IECR, 1);
+ i = bit;
+ }
+ } else {
+ at91_aic_write(AT91_AIC_IDCR, *backups);
+ at91_aic_write(AT91_AIC_IECR, *wakeups);
+ }
+}
+
+void at91_irq_resume(void)
+{
+ int i = 0, bit;
+
+ if (has_aic5()) {
+ /* disable wakeup irqs */
+ while ((bit = find_next_bit(wakeups, n_irqs, i)) < n_irqs) {
+ at91_aic_write(AT91_AIC5_SSR,
+ bit & AT91_AIC5_INTSEL_MSK);
+ at91_aic_write(AT91_AIC5_IDCR, 1);
+ i = bit;
+ }
+ /* enable irqs disabled for suspend */
+ i = 0;
+ while ((bit = find_next_bit(backups, n_irqs, i)) < n_irqs) {
+ at91_aic_write(AT91_AIC5_SSR,
+ bit & AT91_AIC5_INTSEL_MSK);
+ at91_aic_write(AT91_AIC5_IECR, 1);
+ i = bit;
+ }
+ } else {
+ at91_aic_write(AT91_AIC_IDCR, *wakeups);
+ at91_aic_write(AT91_AIC_IECR, *backups);
+ }
+}
+
+#else
+static inline int at91_aic_pm_init(void)
+{
+ return 0;
+}
+
+#define set_backup(bit)
+#define clear_backup(bit)
+#define at91_aic_set_wake NULL
+
+#endif /* CONFIG_PM */
+
+asmlinkage void __exception_irq_entry
+at91_aic_handle_irq(struct pt_regs *regs)
+{
+ u32 irqnr;
+ u32 irqstat;
+
+ irqnr = at91_aic_read(AT91_AIC_IVR);
+ irqstat = at91_aic_read(AT91_AIC_ISR);
+
+ /*
+ * ISR value is 0 when there is no current interrupt or when there is
+ * a spurious interrupt
+ */
+ if (!irqstat)
+ at91_aic_write(AT91_AIC_EOICR, 0);
+ else
+ handle_IRQ(irqnr, regs);
+}
+
+asmlinkage void __exception_irq_entry
+at91_aic5_handle_irq(struct pt_regs *regs)
+{
+ u32 irqnr;
+ u32 irqstat;
+
+ irqnr = at91_aic_read(AT91_AIC5_IVR);
+ irqstat = at91_aic_read(AT91_AIC5_ISR);
+
+ if (!irqstat)
+ at91_aic_write(AT91_AIC5_EOICR, 0);
+ else
+ handle_IRQ(irqnr, regs);
+}
static void at91_aic_mask_irq(struct irq_data *d)
{
/* Disable interrupt on AIC */
at91_aic_write(AT91_AIC_IDCR, 1 << d->hwirq);
+ /* Update ISR cache */
+ clear_backup(d->hwirq);
+}
+
+static void __maybe_unused at91_aic5_mask_irq(struct irq_data *d)
+{
+ /* Disable interrupt on AIC5 */
+ at91_aic_write(AT91_AIC5_SSR, d->hwirq & AT91_AIC5_INTSEL_MSK);
+ at91_aic_write(AT91_AIC5_IDCR, 1);
+ /* Update ISR cache */
+ clear_backup(d->hwirq);
}
static void at91_aic_unmask_irq(struct irq_data *d)
{
/* Enable interrupt on AIC */
at91_aic_write(AT91_AIC_IECR, 1 << d->hwirq);
+ /* Update ISR cache */
+ set_backup(d->hwirq);
+}
+
+static void __maybe_unused at91_aic5_unmask_irq(struct irq_data *d)
+{
+ /* Enable interrupt on AIC5 */
+ at91_aic_write(AT91_AIC5_SSR, d->hwirq & AT91_AIC5_INTSEL_MSK);
+ at91_aic_write(AT91_AIC5_IECR, 1);
+ /* Update ISR cache */
+ set_backup(d->hwirq);
}
-unsigned int at91_extern_irq;
+static void at91_aic_eoi(struct irq_data *d)
+{
+ /*
+ * Mark end-of-interrupt on AIC, the controller doesn't care about
+ * the value written. Moreover it's a write-only register.
+ */
+ at91_aic_write(AT91_AIC_EOICR, 0);
+}
+
+static void __maybe_unused at91_aic5_eoi(struct irq_data *d)
+{
+ at91_aic_write(AT91_AIC5_EOICR, 0);
+}
-#define is_extern_irq(hwirq) ((1 << (hwirq)) & at91_extern_irq)
+unsigned long *at91_extern_irq;
-static int at91_aic_set_type(struct irq_data *d, unsigned type)
+#define is_extern_irq(hwirq) test_bit(hwirq, at91_extern_irq)
+
+static int at91_aic_compute_srctype(struct irq_data *d, unsigned type)
{
- unsigned int smr, srctype;
+ int srctype;
switch (type) {
case IRQ_TYPE_LEVEL_HIGH:
if ((d->hwirq == AT91_ID_FIQ) || is_extern_irq(d->hwirq)) /* only supported on external interrupts */
srctype = AT91_AIC_SRCTYPE_LOW;
else
- return -EINVAL;
+ srctype = -EINVAL;
break;
case IRQ_TYPE_EDGE_FALLING:
if ((d->hwirq == AT91_ID_FIQ) || is_extern_irq(d->hwirq)) /* only supported on external interrupts */
srctype = AT91_AIC_SRCTYPE_FALLING;
else
- return -EINVAL;
+ srctype = -EINVAL;
break;
default:
- return -EINVAL;
+ srctype = -EINVAL;
}
- smr = at91_aic_read(AT91_AIC_SMR(d->hwirq)) & ~AT91_AIC_SRCTYPE;
- at91_aic_write(AT91_AIC_SMR(d->hwirq), smr | srctype);
- return 0;
+ return srctype;
}
-#ifdef CONFIG_PM
-
-static u32 wakeups;
-static u32 backups;
-
-static int at91_aic_set_wake(struct irq_data *d, unsigned value)
+static int at91_aic_set_type(struct irq_data *d, unsigned type)
{
- if (unlikely(d->hwirq >= NR_AIC_IRQS))
- return -EINVAL;
-
- if (value)
- wakeups |= (1 << d->hwirq);
- else
- wakeups &= ~(1 << d->hwirq);
+ unsigned int smr;
+ int srctype;
+
+ srctype = at91_aic_compute_srctype(d, type);
+ if (srctype < 0)
+ return srctype;
+
+ if (has_aic5()) {
+ at91_aic_write(AT91_AIC5_SSR,
+ d->hwirq & AT91_AIC5_INTSEL_MSK);
+ smr = at91_aic_read(AT91_AIC5_SMR) & ~AT91_AIC_SRCTYPE;
+ at91_aic_write(AT91_AIC5_SMR, smr | srctype);
+ } else {
+ smr = at91_aic_read(AT91_AIC_SMR(d->hwirq))
+ & ~AT91_AIC_SRCTYPE;
+ at91_aic_write(AT91_AIC_SMR(d->hwirq), smr | srctype);
+ }
return 0;
}
-void at91_irq_suspend(void)
-{
- backups = at91_aic_read(AT91_AIC_IMR);
- at91_aic_write(AT91_AIC_IDCR, backups);
- at91_aic_write(AT91_AIC_IECR, wakeups);
-}
-
-void at91_irq_resume(void)
-{
- at91_aic_write(AT91_AIC_IDCR, wakeups);
- at91_aic_write(AT91_AIC_IECR, backups);
-}
-
-#else
-#define at91_aic_set_wake NULL
-#endif
-
static struct irq_chip at91_aic_chip = {
.name = "AIC",
- .irq_ack = at91_aic_mask_irq,
.irq_mask = at91_aic_mask_irq,
.irq_unmask = at91_aic_unmask_irq,
.irq_set_type = at91_aic_set_type,
.irq_set_wake = at91_aic_set_wake,
+ .irq_eoi = at91_aic_eoi,
};
static void __init at91_aic_hw_init(unsigned int spu_vector)
at91_aic_write(AT91_AIC_ICCR, 0xFFFFFFFF);
}
+static void __init __maybe_unused at91_aic5_hw_init(unsigned int spu_vector)
+{
+ int i;
+
+ /*
+ * Perform 8 End Of Interrupt Command to make sure AIC
+ * will not Lock out nIRQ
+ */
+ for (i = 0; i < 8; i++)
+ at91_aic_write(AT91_AIC5_EOICR, 0);
+
+ /*
+ * Spurious Interrupt ID in Spurious Vector Register.
+ * When there is no current interrupt, the IRQ Vector Register
+ * reads the value stored in AIC_SPU
+ */
+ at91_aic_write(AT91_AIC5_SPU, spu_vector);
+
+ /* No debugging in AIC: Debug (Protect) Control Register */
+ at91_aic_write(AT91_AIC5_DCR, 0);
+
+ /* Disable and clear all interrupts initially */
+ for (i = 0; i < n_irqs; i++) {
+ at91_aic_write(AT91_AIC5_SSR, i & AT91_AIC5_INTSEL_MSK);
+ at91_aic_write(AT91_AIC5_IDCR, 1);
+ at91_aic_write(AT91_AIC5_ICCR, 1);
+ }
+}
+
#if defined(CONFIG_OF)
+static unsigned int *at91_aic_irq_priorities;
+
static int at91_aic_irq_map(struct irq_domain *h, unsigned int virq,
irq_hw_number_t hw)
{
/* Put virq number in Source Vector Register */
at91_aic_write(AT91_AIC_SVR(hw), virq);
- /* Active Low interrupt, without priority */
- at91_aic_write(AT91_AIC_SMR(hw), AT91_AIC_SRCTYPE_LOW);
+ /* Active Low interrupt, with priority */
+ at91_aic_write(AT91_AIC_SMR(hw),
+ AT91_AIC_SRCTYPE_LOW | at91_aic_irq_priorities[hw]);
- irq_set_chip_and_handler(virq, &at91_aic_chip, handle_level_irq);
+ irq_set_chip_and_handler(virq, &at91_aic_chip, handle_fasteoi_irq);
set_irq_flags(virq, IRQF_VALID | IRQF_PROBE);
return 0;
}
+static int at91_aic5_irq_map(struct irq_domain *h, unsigned int virq,
+ irq_hw_number_t hw)
+{
+ at91_aic_write(AT91_AIC5_SSR, hw & AT91_AIC5_INTSEL_MSK);
+
+ /* Put virq number in Source Vector Register */
+ at91_aic_write(AT91_AIC5_SVR, virq);
+
+ /* Active Low interrupt, with priority */
+ at91_aic_write(AT91_AIC5_SMR,
+ AT91_AIC_SRCTYPE_LOW | at91_aic_irq_priorities[hw]);
+
+ irq_set_chip_and_handler(virq, &at91_aic_chip, handle_fasteoi_irq);
+ set_irq_flags(virq, IRQF_VALID | IRQF_PROBE);
+
+ return 0;
+}
+
+static int at91_aic_irq_domain_xlate(struct irq_domain *d, struct device_node *ctrlr,
+ const u32 *intspec, unsigned int intsize,
+ irq_hw_number_t *out_hwirq, unsigned int *out_type)
+{
+ if (WARN_ON(intsize < 3))
+ return -EINVAL;
+ if (WARN_ON(intspec[0] >= n_irqs))
+ return -EINVAL;
+ if (WARN_ON((intspec[2] < AT91_AIC_IRQ_MIN_PRIORITY)
+ || (intspec[2] > AT91_AIC_IRQ_MAX_PRIORITY)))
+ return -EINVAL;
+
+ *out_hwirq = intspec[0];
+ *out_type = intspec[1] & IRQ_TYPE_SENSE_MASK;
+ at91_aic_irq_priorities[*out_hwirq] = intspec[2];
+
+ return 0;
+}
+
static struct irq_domain_ops at91_aic_irq_ops = {
.map = at91_aic_irq_map,
- .xlate = irq_domain_xlate_twocell,
+ .xlate = at91_aic_irq_domain_xlate,
};
-int __init at91_aic_of_init(struct device_node *node,
- struct device_node *parent)
+int __init at91_aic_of_common_init(struct device_node *node,
+ struct device_node *parent)
{
+ struct property *prop;
+ const __be32 *p;
+ u32 val;
+
+ at91_extern_irq = kzalloc(BITS_TO_LONGS(n_irqs)
+ * sizeof(*at91_extern_irq), GFP_KERNEL);
+ if (!at91_extern_irq)
+ return -ENOMEM;
+
+ if (at91_aic_pm_init()) {
+ kfree(at91_extern_irq);
+ return -ENOMEM;
+ }
+
+ at91_aic_irq_priorities = kzalloc(n_irqs
+ * sizeof(*at91_aic_irq_priorities),
+ GFP_KERNEL);
+ if (!at91_aic_irq_priorities)
+ return -ENOMEM;
+
at91_aic_base = of_iomap(node, 0);
at91_aic_np = node;
- at91_aic_domain = irq_domain_add_linear(at91_aic_np, NR_AIC_IRQS,
+ at91_aic_domain = irq_domain_add_linear(at91_aic_np, n_irqs,
&at91_aic_irq_ops, NULL);
if (!at91_aic_domain)
panic("Unable to add AIC irq domain (DT)\n");
+ of_property_for_each_u32(node, "atmel,external-irqs", prop, p, val) {
+ if (val >= n_irqs)
+ pr_warn("AIC: external irq %d >= %d skip it\n",
+ val, n_irqs);
+ else
+ set_bit(val, at91_extern_irq);
+ }
+
irq_set_default_host(at91_aic_domain);
- at91_aic_hw_init(NR_AIC_IRQS);
+ return 0;
+}
+
+int __init at91_aic_of_init(struct device_node *node,
+ struct device_node *parent)
+{
+ int err;
+
+ err = at91_aic_of_common_init(node, parent);
+ if (err)
+ return err;
+
+ at91_aic_hw_init(n_irqs);
+
+ return 0;
+}
+
+int __init at91_aic5_of_init(struct device_node *node,
+ struct device_node *parent)
+{
+ int err;
+
+ at91_aic_caps |= AT91_AIC_CAP_AIC5;
+ n_irqs = NR_AIC5_IRQS;
+ at91_aic_chip.irq_ack = at91_aic5_mask_irq;
+ at91_aic_chip.irq_mask = at91_aic5_mask_irq;
+ at91_aic_chip.irq_unmask = at91_aic5_unmask_irq;
+ at91_aic_chip.irq_eoi = at91_aic5_eoi;
+ at91_aic_irq_ops.map = at91_aic5_irq_map;
+
+ err = at91_aic_of_common_init(node, parent);
+ if (err)
+ return err;
+
+ at91_aic5_hw_init(n_irqs);
return 0;
}
/*
* Initialize the AIC interrupt controller.
*/
-void __init at91_aic_init(unsigned int priority[NR_AIC_IRQS])
+void __init at91_aic_init(unsigned int *priority)
{
unsigned int i;
int irq_base;
+ if (at91_aic_pm_init())
+ panic("Unable to allocate bit maps\n");
+
at91_aic_base = ioremap(AT91_AIC, 512);
if (!at91_aic_base)
panic("Unable to ioremap AIC registers\n");
/* Add irq domain for AIC */
- irq_base = irq_alloc_descs(-1, 0, NR_AIC_IRQS, 0);
+ irq_base = irq_alloc_descs(-1, 0, n_irqs, 0);
if (irq_base < 0) {
WARN(1, "Cannot allocate irq_descs, assuming pre-allocated\n");
irq_base = 0;
}
- at91_aic_domain = irq_domain_add_legacy(at91_aic_np, NR_AIC_IRQS,
+ at91_aic_domain = irq_domain_add_legacy(at91_aic_np, n_irqs,
irq_base, 0,
&irq_domain_simple_ops, NULL);
* The IVR is used by macro get_irqnr_and_base to read and verify.
* The irq number is NR_AIC_IRQS when a spurious interrupt has occurred.
*/
- for (i = 0; i < NR_AIC_IRQS; i++) {
+ for (i = 0; i < n_irqs; i++) {
/* Put hardware irq number in Source Vector Register: */
- at91_aic_write(AT91_AIC_SVR(i), i);
+ at91_aic_write(AT91_AIC_SVR(i), NR_IRQS_LEGACY + i);
/* Active Low interrupt, with the specified priority */
at91_aic_write(AT91_AIC_SMR(i), AT91_AIC_SRCTYPE_LOW | priority[i]);
-
- irq_set_chip_and_handler(i, &at91_aic_chip, handle_level_irq);
+ irq_set_chip_and_handler(NR_IRQS_LEGACY + i, &at91_aic_chip, handle_fasteoi_irq);
set_irq_flags(i, IRQF_VALID | IRQF_PROBE);
}
- at91_aic_hw_init(NR_AIC_IRQS);
+ at91_aic_hw_init(n_irqs);
}
#include <asm/mach/time.h>
#include <asm/mach/irq.h>
+#include <mach/at91_aic.h>
#include <mach/at91_pmc.h>
#include <mach/cpu.h>
#include <plat/board-ams-delta.h>
#include <plat/keypad.h>
#include <plat/mux.h>
-#include <plat/usb.h>
#include <plat/board.h>
#include <mach/hardware.h>
#include <mach/ams-delta-fiq.h>
#include <mach/camera.h>
+#include <mach/usb.h>
#include "iomap.h"
#include "common.h"
#include <asm/mach/map.h>
#include <plat/mux.h>
-#include <plat/usb.h>
#include <plat/board.h>
+
+#include <mach/usb.h>
+
#include "common.h"
/* assume no Mini-AB port */
#include <plat/dma.h>
#include <plat/tc.h>
#include <plat/irda.h>
-#include <plat/usb.h>
#include <plat/keypad.h>
#include <plat/flash.h>
#include <mach/hardware.h>
+#include <mach/usb.h>
#include "common.h"
#include "board-h2.h"
#include <plat/mux.h>
#include <plat/tc.h>
-#include <plat/usb.h>
#include <plat/keypad.h>
#include <plat/dma.h>
#include <plat/flash.h>
#include <mach/hardware.h>
#include <mach/irqs.h>
+#include <mach/usb.h>
#include "common.h"
#include "board-h3.h"
#include <plat/omap7xx.h>
#include <plat/board.h>
#include <plat/keypad.h>
-#include <plat/usb.h>
#include <plat/mmc.h>
#include <mach/irqs.h>
+#include <mach/usb.h>
#include "common.h"
#include <plat/flash.h>
#include <plat/fpga.h>
#include <plat/tc.h>
-#include <plat/usb.h>
#include <plat/keypad.h>
#include <plat/mmc.h>
#include <mach/hardware.h>
+#include <mach/usb.h>
#include "iomap.h"
#include "common.h"
#include <asm/mach/map.h>
#include <plat/mux.h>
-#include <plat/usb.h>
#include <plat/board.h>
#include <plat/keypad.h>
#include <plat/lcd_mipid.h>
#include <plat/clock.h>
#include <mach/hardware.h>
+#include <mach/usb.h>
#include "common.h"
#include <asm/mach/map.h>
#include <plat/flash.h>
-#include <plat/usb.h>
#include <plat/mux.h>
#include <plat/tc.h>
#include <mach/hardware.h>
+#include <mach/usb.h>
#include "common.h"
#include <plat/flash.h>
#include <plat/mux.h>
-#include <plat/usb.h>
#include <plat/tc.h>
#include <plat/dma.h>
#include <plat/board.h>
#include <plat/keypad.h>
#include <mach/hardware.h>
+#include <mach/usb.h>
#include "common.h"
#include <plat/led.h>
#include <plat/flash.h>
#include <plat/mux.h>
-#include <plat/usb.h>
#include <plat/dma.h>
#include <plat/tc.h>
#include <plat/board.h>
#include <plat/keypad.h>
#include <mach/hardware.h>
+#include <mach/usb.h>
#include "common.h"
#include <plat/flash.h>
#include <plat/mux.h>
-#include <plat/usb.h>
#include <plat/dma.h>
#include <plat/tc.h>
#include <plat/board.h>
#include <plat/keypad.h>
#include <mach/hardware.h>
+#include <mach/usb.h>
#include "common.h"
#include <plat/mux.h>
#include <plat/dma.h>
#include <plat/irda.h>
-#include <plat/usb.h>
#include <plat/tc.h>
#include <plat/board.h>
#include <plat/keypad.h>
#include <plat/board-sx1.h>
#include <mach/hardware.h>
+#include <mach/usb.h>
#include "common.h"
#include <plat/flash.h>
#include <plat/mux.h>
#include <plat/tc.h>
-#include <plat/usb.h>
+#include <plat/board.h>
#include <mach/hardware.h>
+#include <mach/usb.h>
#include "common.h"
#include <plat/clock.h>
#include <plat/cpu.h>
#include <plat/clkdev_omap.h>
+#include <plat/board.h>
#include <plat/sram.h> /* for omap_sram_reprogram_clock() */
-#include <plat/usb.h> /* for OTG_BASE */
#include <mach/hardware.h>
+#include <mach/usb.h> /* for OTG_BASE */
#include "iomap.h"
#include "clock.h"
--- /dev/null
+/*
+ * FIXME correct answer depends on hmc_mode,
+ * as does (on omap1) any nonzero value for config->otg port number
+ */
+#ifdef CONFIG_USB_GADGET_OMAP
+#define is_usb0_device(config) 1
+#else
+#define is_usb0_device(config) 0
+#endif
+
+struct omap_usb_config {
+ /* Configure drivers according to the connectors on your board:
+ * - "A" connector (rectagular)
+ * ... for host/OHCI use, set "register_host".
+ * - "B" connector (squarish) or "Mini-B"
+ * ... for device/gadget use, set "register_dev".
+ * - "Mini-AB" connector (very similar to Mini-B)
+ * ... for OTG use as device OR host, initialize "otg"
+ */
+ unsigned register_host:1;
+ unsigned register_dev:1;
+ u8 otg; /* port number, 1-based: usb1 == 2 */
+
+ u8 hmc_mode;
+
+ /* implicitly true if otg: host supports remote wakeup? */
+ u8 rwc;
+
+ /* signaling pins used to talk to transceiver on usbN:
+ * 0 == usbN unused
+ * 2 == usb0-only, using internal transceiver
+ * 3 == 3 wire bidirectional
+ * 4 == 4 wire bidirectional
+ * 6 == 6 wire unidirectional (or TLL)
+ */
+ u8 pins[3];
+
+ struct platform_device *udc_device;
+ struct platform_device *ohci_device;
+ struct platform_device *otg_device;
+
+ u32 (*usb0_init)(unsigned nwires, unsigned is_device);
+ u32 (*usb1_init)(unsigned nwires);
+ u32 (*usb2_init)(unsigned nwires, unsigned alt_pingroup);
+
+ int (*ocpi_enable)(void);
+};
+
+void omap_otg_init(struct omap_usb_config *config);
+
+#if defined(CONFIG_USB) || defined(CONFIG_USB_MODULE)
+void omap1_usb_init(struct omap_usb_config *pdata);
+#else
+static inline void omap1_usb_init(struct omap_usb_config *pdata)
+{
+}
+#endif
+
+#define OMAP1_OTG_BASE 0xfffb0400
+#define OMAP1_UDC_BASE 0xfffb4000
+#define OMAP1_OHCI_BASE 0xfffba000
+
+#define OMAP2_OHCI_BASE 0x4805e000
+#define OMAP2_UDC_BASE 0x4805e200
+#define OMAP2_OTG_BASE 0x4805e300
+#define OTG_BASE OMAP1_OTG_BASE
+#define UDC_BASE OMAP1_UDC_BASE
+#define OMAP_OHCI_BASE OMAP1_OHCI_BASE
+
+/*
+ * OTG and transceiver registers, for OMAPs starting with ARM926
+ */
+#define OTG_REV (OTG_BASE + 0x00)
+#define OTG_SYSCON_1 (OTG_BASE + 0x04)
+# define USB2_TRX_MODE(w) (((w)>>24)&0x07)
+# define USB1_TRX_MODE(w) (((w)>>20)&0x07)
+# define USB0_TRX_MODE(w) (((w)>>16)&0x07)
+# define OTG_IDLE_EN (1 << 15)
+# define HST_IDLE_EN (1 << 14)
+# define DEV_IDLE_EN (1 << 13)
+# define OTG_RESET_DONE (1 << 2)
+# define OTG_SOFT_RESET (1 << 1)
+#define OTG_SYSCON_2 (OTG_BASE + 0x08)
+# define OTG_EN (1 << 31)
+# define USBX_SYNCHRO (1 << 30)
+# define OTG_MST16 (1 << 29)
+# define SRP_GPDATA (1 << 28)
+# define SRP_GPDVBUS (1 << 27)
+# define SRP_GPUVBUS(w) (((w)>>24)&0x07)
+# define A_WAIT_VRISE(w) (((w)>>20)&0x07)
+# define B_ASE_BRST(w) (((w)>>16)&0x07)
+# define SRP_DPW (1 << 14)
+# define SRP_DATA (1 << 13)
+# define SRP_VBUS (1 << 12)
+# define OTG_PADEN (1 << 10)
+# define HMC_PADEN (1 << 9)
+# define UHOST_EN (1 << 8)
+# define HMC_TLLSPEED (1 << 7)
+# define HMC_TLLATTACH (1 << 6)
+# define OTG_HMC(w) (((w)>>0)&0x3f)
+#define OTG_CTRL (OTG_BASE + 0x0c)
+# define OTG_USB2_EN (1 << 29)
+# define OTG_USB2_DP (1 << 28)
+# define OTG_USB2_DM (1 << 27)
+# define OTG_USB1_EN (1 << 26)
+# define OTG_USB1_DP (1 << 25)
+# define OTG_USB1_DM (1 << 24)
+# define OTG_USB0_EN (1 << 23)
+# define OTG_USB0_DP (1 << 22)
+# define OTG_USB0_DM (1 << 21)
+# define OTG_ASESSVLD (1 << 20)
+# define OTG_BSESSEND (1 << 19)
+# define OTG_BSESSVLD (1 << 18)
+# define OTG_VBUSVLD (1 << 17)
+# define OTG_ID (1 << 16)
+# define OTG_DRIVER_SEL (1 << 15)
+# define OTG_A_SETB_HNPEN (1 << 12)
+# define OTG_A_BUSREQ (1 << 11)
+# define OTG_B_HNPEN (1 << 9)
+# define OTG_B_BUSREQ (1 << 8)
+# define OTG_BUSDROP (1 << 7)
+# define OTG_PULLDOWN (1 << 5)
+# define OTG_PULLUP (1 << 4)
+# define OTG_DRV_VBUS (1 << 3)
+# define OTG_PD_VBUS (1 << 2)
+# define OTG_PU_VBUS (1 << 1)
+# define OTG_PU_ID (1 << 0)
+#define OTG_IRQ_EN (OTG_BASE + 0x10) /* 16-bit */
+# define DRIVER_SWITCH (1 << 15)
+# define A_VBUS_ERR (1 << 13)
+# define A_REQ_TMROUT (1 << 12)
+# define A_SRP_DETECT (1 << 11)
+# define B_HNP_FAIL (1 << 10)
+# define B_SRP_TMROUT (1 << 9)
+# define B_SRP_DONE (1 << 8)
+# define B_SRP_STARTED (1 << 7)
+# define OPRT_CHG (1 << 0)
+#define OTG_IRQ_SRC (OTG_BASE + 0x14) /* 16-bit */
+ // same bits as in IRQ_EN
+#define OTG_OUTCTRL (OTG_BASE + 0x18) /* 16-bit */
+# define OTGVPD (1 << 14)
+# define OTGVPU (1 << 13)
+# define OTGPUID (1 << 12)
+# define USB2VDR (1 << 10)
+# define USB2PDEN (1 << 9)
+# define USB2PUEN (1 << 8)
+# define USB1VDR (1 << 6)
+# define USB1PDEN (1 << 5)
+# define USB1PUEN (1 << 4)
+# define USB0VDR (1 << 2)
+# define USB0PDEN (1 << 1)
+# define USB0PUEN (1 << 0)
+#define OTG_TEST (OTG_BASE + 0x20) /* 16-bit */
+#define OTG_VENDOR_CODE (OTG_BASE + 0xfc) /* 16-bit */
+
+/*-------------------------------------------------------------------------*/
+
+/* OMAP1 */
+#define USB_TRANSCEIVER_CTRL (0xfffe1000 + 0x0064)
+# define CONF_USB2_UNI_R (1 << 8)
+# define CONF_USB1_UNI_R (1 << 7)
+# define CONF_USB_PORT0_R(x) (((x)>>4)&0x7)
+# define CONF_USB0_ISOLATE_R (1 << 3)
+# define CONF_USB_PWRDN_DM_R (1 << 2)
+# define CONF_USB_PWRDN_DP_R (1 << 1)
#include <asm/irq.h>
#include <plat/mux.h>
-#include <plat/usb.h>
+
+#include <mach/usb.h>
#include "common.h"
#define INT_USB_IRQ_HGEN INT_USB_HHC_1
#define INT_USB_IRQ_OTG IH2_BASE + 8
+#ifdef CONFIG_ARCH_OMAP_OTG
+
+void __init
+omap_otg_init(struct omap_usb_config *config)
+{
+ u32 syscon;
+ int alt_pingroup = 0;
+
+ /* NOTE: no bus or clock setup (yet?) */
+
+ syscon = omap_readl(OTG_SYSCON_1) & 0xffff;
+ if (!(syscon & OTG_RESET_DONE))
+ pr_debug("USB resets not complete?\n");
+
+ //omap_writew(0, OTG_IRQ_EN);
+
+ /* pin muxing and transceiver pinouts */
+ if (config->pins[0] > 2) /* alt pingroup 2 */
+ alt_pingroup = 1;
+ syscon |= config->usb0_init(config->pins[0], is_usb0_device(config));
+ syscon |= config->usb1_init(config->pins[1]);
+ syscon |= config->usb2_init(config->pins[2], alt_pingroup);
+ pr_debug("OTG_SYSCON_1 = %08x\n", omap_readl(OTG_SYSCON_1));
+ omap_writel(syscon, OTG_SYSCON_1);
+
+ syscon = config->hmc_mode;
+ syscon |= USBX_SYNCHRO | (4 << 16) /* B_ASE0_BRST */;
+#ifdef CONFIG_USB_OTG
+ if (config->otg)
+ syscon |= OTG_EN;
+#endif
+ if (cpu_class_is_omap1())
+ pr_debug("USB_TRANSCEIVER_CTRL = %03x\n",
+ omap_readl(USB_TRANSCEIVER_CTRL));
+ pr_debug("OTG_SYSCON_2 = %08x\n", omap_readl(OTG_SYSCON_2));
+ omap_writel(syscon, OTG_SYSCON_2);
+
+ printk("USB: hmc %d", config->hmc_mode);
+ if (!alt_pingroup)
+ printk(", usb2 alt %d wires", config->pins[2]);
+ else if (config->pins[0])
+ printk(", usb0 %d wires%s", config->pins[0],
+ is_usb0_device(config) ? " (dev)" : "");
+ if (config->pins[1])
+ printk(", usb1 %d wires", config->pins[1]);
+ if (!alt_pingroup && config->pins[2])
+ printk(", usb2 %d wires", config->pins[2]);
+ if (config->otg)
+ printk(", Mini-AB on usb%d", config->otg - 1);
+ printk("\n");
+
+ if (cpu_class_is_omap1()) {
+ u16 w;
+
+ /* leave USB clocks/controllers off until needed */
+ w = omap_readw(ULPD_SOFT_REQ);
+ w &= ~SOFT_USB_CLK_REQ;
+ omap_writew(w, ULPD_SOFT_REQ);
+
+ w = omap_readw(ULPD_CLOCK_CTRL);
+ w &= ~USB_MCLK_EN;
+ w |= DIS_USB_PVCI_CLK;
+ omap_writew(w, ULPD_CLOCK_CTRL);
+ }
+ syscon = omap_readl(OTG_SYSCON_1);
+ syscon |= HST_IDLE_EN|DEV_IDLE_EN|OTG_IDLE_EN;
+
+#ifdef CONFIG_USB_GADGET_OMAP
+ if (config->otg || config->register_dev) {
+ struct platform_device *udc_device = config->udc_device;
+ int status;
+
+ syscon &= ~DEV_IDLE_EN;
+ udc_device->dev.platform_data = config;
+ status = platform_device_register(udc_device);
+ if (status)
+ pr_debug("can't register UDC device, %d\n", status);
+ }
+#endif
+
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+ if (config->otg || config->register_host) {
+ struct platform_device *ohci_device = config->ohci_device;
+ int status;
+
+ syscon &= ~HST_IDLE_EN;
+ ohci_device->dev.platform_data = config;
+ status = platform_device_register(ohci_device);
+ if (status)
+ pr_debug("can't register OHCI device, %d\n", status);
+ }
+#endif
+
+#ifdef CONFIG_USB_OTG
+ if (config->otg) {
+ struct platform_device *otg_device = config->otg_device;
+ int status;
+
+ syscon &= ~OTG_IDLE_EN;
+ otg_device->dev.platform_data = config;
+ status = platform_device_register(otg_device);
+ if (status)
+ pr_debug("can't register OTG device, %d\n", status);
+ }
+#endif
+ pr_debug("OTG_SYSCON_1 = %08x\n", omap_readl(OTG_SYSCON_1));
+ omap_writel(syscon, OTG_SYSCON_1);
+}
+
+#else
+void omap_otg_init(struct omap_usb_config *config) {}
+#endif
+
#ifdef CONFIG_USB_GADGET_OMAP
static struct resource udc_resources[] = {
depends on ARCH_OMAP2
default y
select OMAP_DM_TIMER
- select ARCH_OMAP_OTG
config SOC_OMAP2430
bool "OMAP2430 support"
depends on ARCH_OMAP2
default y
- select ARCH_OMAP_OTG
config SOC_OMAP3430
bool "OMAP3430 support"
depends on ARCH_OMAP3
default y
- select ARCH_OMAP_OTG
config SOC_TI81XX
bool "TI81XX support"
# PRCM clockdomain control
clockdomain-common += clockdomain.o
-clockdomain-common += clockdomains_common_data.o
obj-$(CONFIG_ARCH_OMAP2) += $(clockdomain-common)
obj-$(CONFIG_ARCH_OMAP2) += clockdomain2xxx_3xxx.o
obj-$(CONFIG_ARCH_OMAP2) += clockdomains2xxx_3xxx_data.o
omap-hsmmc-$(CONFIG_MMC_OMAP_HS) := hsmmc.o
obj-y += $(omap-hsmmc-m) $(omap-hsmmc-y)
-
-usbfs-$(CONFIG_ARCH_OMAP_OTG) := usb-fs.o
-obj-y += $(usbfs-m) $(usbfs-y)
obj-y += usb-musb.o
obj-y += omap_phy_internal.o
{} /* Terminator */
};
-static struct omap_usb_config sdp2430_usb_config __initdata = {
- .otg = 1,
-#ifdef CONFIG_USB_GADGET_OMAP
- .hmc_mode = 0x0,
-#elif defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
- .hmc_mode = 0x1,
-#endif
- .pins[0] = 3,
-};
-
#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
{ .reg_offset = OMAP_MUX_TERMINATOR },
omap_serial_init();
omap_sdrc_init(NULL, NULL);
omap_hsmmc_init(mmc);
- omap2_usbfs_init(&sdp2430_usb_config);
omap_mux_init_signal("usb0hs_stp", OMAP_PULL_ENA | OMAP_PULL_UP);
usb_musb_init(NULL);
#include <asm/mach/flash.h>
#include <plat/led.h>
-#include <plat/usb.h>
#include <plat/board.h>
#include "common.h"
#include <plat/gpmc.h>
clk_put(gpmc_fck);
}
-static struct omap_usb_config apollon_usb_config __initdata = {
- .register_dev = 1,
- .hmc_mode = 0x14, /* 0:dev 1:host1 2:disable */
-
- .pins[0] = 6,
-};
-
static struct panel_generic_dpi_data apollon_panel_data = {
.name = "apollon",
};
gpio_request_array(apollon_gpio_leds, ARRAY_SIZE(apollon_gpio_leds));
}
-static void __init apollon_usb_init(void)
-{
- /* USB device */
- /* DEVICE_SUSPEND */
- omap_mux_init_signal("mcbsp2_clkx.gpio_12", 0);
- gpio_request_one(12, GPIOF_OUT_INIT_LOW, "USB suspend");
- omap2_usbfs_init(&apollon_usb_config);
-}
-
#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
{ .reg_offset = OMAP_MUX_TERMINATOR },
apollon_init_smc91x();
apollon_led_init();
apollon_flash_init();
- apollon_usb_init();
/* REVISIT: where's the correct place */
omap_mux_init_signal("sys_nirq", OMAP_PULL_ENA | OMAP_PULL_UP);
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <plat/usb.h>
#include <plat/board.h>
#include "common.h"
#include <plat/menelaus.h>
h4_flash_resource.end = base + SZ_64M - 1;
}
-static struct omap_usb_config h4_usb_config __initdata = {
- /* S1.10 OFF -- usb "download port"
- * usb0 switched to Mini-B port and isp1105 transceiver;
- * S2.POS3 = ON, S2.POS4 = OFF ... to enable battery charging
- */
- .register_dev = 1,
- .pins[0] = 3,
-/* .hmc_mode = 0x14,*/ /* 0:dev 1:host 2:disable */
- .hmc_mode = 0x00, /* 0:dev|otg 1:disable 2:disable */
-};
-
static struct at24_platform_data m24c01 = {
.byte_len = SZ_1K / 8,
.page_size = 16,
ARRAY_SIZE(h4_i2c_board_info));
platform_add_devices(h4_devices, ARRAY_SIZE(h4_devices));
- omap2_usbfs_init(&h4_usb_config);
omap_serial_init();
omap_sdrc_init(NULL, NULL);
h4_init_flash();
CLK(NULL, "osc_ck", &osc_ck, CK_242X),
CLK(NULL, "sys_ck", &sys_ck, CK_242X),
CLK(NULL, "alt_ck", &alt_ck, CK_242X),
- CLK("omap-mcbsp.1", "pad_fck", &mcbsp_clks, CK_242X),
- CLK("omap-mcbsp.2", "pad_fck", &mcbsp_clks, CK_242X),
CLK(NULL, "mcbsp_clks", &mcbsp_clks, CK_242X),
/* internal analog sources */
CLK(NULL, "dpll_ck", &dpll_ck, CK_242X),
/* internal prcm root sources */
CLK(NULL, "func_54m_ck", &func_54m_ck, CK_242X),
CLK(NULL, "core_ck", &core_ck, CK_242X),
- CLK("omap-mcbsp.1", "prcm_fck", &func_96m_ck, CK_242X),
- CLK("omap-mcbsp.2", "prcm_fck", &func_96m_ck, CK_242X),
CLK(NULL, "func_96m_ck", &func_96m_ck, CK_242X),
CLK(NULL, "func_48m_ck", &func_48m_ck, CK_242X),
CLK(NULL, "func_12m_ck", &func_12m_ck, CK_242X),
CLK(NULL, "osc_ck", &osc_ck, CK_243X),
CLK(NULL, "sys_ck", &sys_ck, CK_243X),
CLK(NULL, "alt_ck", &alt_ck, CK_243X),
- CLK("omap-mcbsp.1", "pad_fck", &mcbsp_clks, CK_243X),
- CLK("omap-mcbsp.2", "pad_fck", &mcbsp_clks, CK_243X),
- CLK("omap-mcbsp.3", "pad_fck", &mcbsp_clks, CK_243X),
- CLK("omap-mcbsp.4", "pad_fck", &mcbsp_clks, CK_243X),
- CLK("omap-mcbsp.5", "pad_fck", &mcbsp_clks, CK_243X),
CLK(NULL, "mcbsp_clks", &mcbsp_clks, CK_243X),
/* internal analog sources */
CLK(NULL, "dpll_ck", &dpll_ck, CK_243X),
/* internal prcm root sources */
CLK(NULL, "func_54m_ck", &func_54m_ck, CK_243X),
CLK(NULL, "core_ck", &core_ck, CK_243X),
- CLK("omap-mcbsp.1", "prcm_fck", &func_96m_ck, CK_243X),
- CLK("omap-mcbsp.2", "prcm_fck", &func_96m_ck, CK_243X),
- CLK("omap-mcbsp.3", "prcm_fck", &func_96m_ck, CK_243X),
- CLK("omap-mcbsp.4", "prcm_fck", &func_96m_ck, CK_243X),
- CLK("omap-mcbsp.5", "prcm_fck", &func_96m_ck, CK_243X),
CLK(NULL, "func_96m_ck", &func_96m_ck, CK_243X),
CLK(NULL, "func_48m_ck", &func_48m_ck, CK_243X),
CLK(NULL, "func_12m_ck", &func_12m_ck, CK_243X),
CLK(NULL, "osc_sys_ck", &osc_sys_ck, CK_3XXX),
CLK(NULL, "sys_ck", &sys_ck, CK_3XXX),
CLK(NULL, "sys_altclk", &sys_altclk, CK_3XXX),
- CLK("omap-mcbsp.1", "pad_fck", &mcbsp_clks, CK_3XXX),
- CLK("omap-mcbsp.2", "pad_fck", &mcbsp_clks, CK_3XXX),
- CLK("omap-mcbsp.3", "pad_fck", &mcbsp_clks, CK_3XXX),
- CLK("omap-mcbsp.4", "pad_fck", &mcbsp_clks, CK_3XXX),
- CLK("omap-mcbsp.5", "pad_fck", &mcbsp_clks, CK_3XXX),
CLK(NULL, "mcbsp_clks", &mcbsp_clks, CK_3XXX),
CLK(NULL, "sys_clkout1", &sys_clkout1, CK_3XXX),
CLK(NULL, "dpll1_ck", &dpll1_ck, CK_3XXX),
CLK(NULL, "ts_fck", &ts_fck, CK_3430ES2PLUS | CK_AM35XX | CK_36XX),
CLK(NULL, "usbtll_fck", &usbtll_fck, CK_3430ES2PLUS | CK_AM35XX | CK_36XX),
CLK("usbhs_omap", "usbtll_fck", &usbtll_fck, CK_3430ES2PLUS | CK_AM35XX | CK_36XX),
- CLK("omap-mcbsp.1", "prcm_fck", &core_96m_fck, CK_3XXX),
- CLK("omap-mcbsp.5", "prcm_fck", &core_96m_fck, CK_3XXX),
CLK(NULL, "core_96m_fck", &core_96m_fck, CK_3XXX),
CLK(NULL, "mmchs3_fck", &mmchs3_fck, CK_3430ES2PLUS | CK_AM35XX | CK_36XX),
CLK(NULL, "mmchs2_fck", &mmchs2_fck, CK_3XXX),
CLK(NULL, "omap_32ksync_ick", &omap_32ksync_ick, CK_3XXX),
CLK(NULL, "gpt12_ick", &gpt12_ick, CK_3XXX),
CLK(NULL, "gpt1_ick", &gpt1_ick, CK_3XXX),
- CLK("omap-mcbsp.2", "prcm_fck", &per_96m_fck, CK_3XXX),
- CLK("omap-mcbsp.3", "prcm_fck", &per_96m_fck, CK_3XXX),
- CLK("omap-mcbsp.4", "prcm_fck", &per_96m_fck, CK_3XXX),
CLK(NULL, "per_96m_fck", &per_96m_fck, CK_3XXX),
CLK(NULL, "per_48m_fck", &per_48m_fck, CK_3XXX),
CLK(NULL, "uart3_fck", &uart3_fck, CK_3XXX),
extern struct clkdm_dep gfx_24xx_wkdeps[];
extern struct clkdm_dep dsp_24xx_wkdeps[];
extern struct clockdomain wkup_common_clkdm;
-extern struct clockdomain prm_common_clkdm;
-extern struct clockdomain cm_common_clkdm;
#endif
static struct clockdomain *clockdomains_omap242x[] __initdata = {
&wkup_common_clkdm,
- &cm_common_clkdm,
- &prm_common_clkdm,
&mpu_2420_clkdm,
&iva1_2420_clkdm,
&dsp_2420_clkdm,
static struct clockdomain *clockdomains_omap243x[] __initdata = {
&wkup_common_clkdm,
- &cm_common_clkdm,
- &prm_common_clkdm,
&mpu_2430_clkdm,
&mdm_clkdm,
&dsp_2430_clkdm,
static struct clockdomain *clockdomains_omap3430_common[] __initdata = {
&wkup_common_clkdm,
- &cm_common_clkdm,
- &prm_common_clkdm,
&mpu_3xxx_clkdm,
&neon_clkdm,
&iva2_clkdm,
&l4_wkup_44xx_clkdm,
&emu_sys_44xx_clkdm,
&l3_dma_44xx_clkdm,
- &prm_common_clkdm,
- &cm_common_clkdm,
NULL
};
+++ /dev/null
-/*
- * OMAP2+-common clockdomain data
- *
- * Copyright (C) 2008-2012 Texas Instruments, Inc.
- * Copyright (C) 2008-2010 Nokia Corporation
- *
- * Paul Walmsley, Jouni Högander
- */
-
-#include <linux/kernel.h>
-#include <linux/io.h>
-
-#include "clockdomain.h"
-
-/* These are implicit clockdomains - they are never defined as such in TRM */
-struct clockdomain prm_common_clkdm = {
- .name = "prm_clkdm",
- .pwrdm = { .name = "wkup_pwrdm" },
-};
-
-struct clockdomain cm_common_clkdm = {
- .name = "cm_clkdm",
- .pwrdm = { .name = "core_pwrdm" },
-};
#endif
+/**
+ * omap_ctrl_write_dsp_boot_addr - set boot address for a remote processor
+ * @bootaddr: physical address of the boot loader
+ *
+ * Set boot address for the boot loader of a supported processor
+ * when a power ON sequence occurs.
+ */
+void omap_ctrl_write_dsp_boot_addr(u32 bootaddr)
+{
+ u32 offset = cpu_is_omap243x() ? OMAP243X_CONTROL_IVA2_BOOTADDR :
+ cpu_is_omap34xx() ? OMAP343X_CONTROL_IVA2_BOOTADDR :
+ cpu_is_omap44xx() ? OMAP4_CTRL_MODULE_CORE_DSP_BOOTADDR :
+ 0;
+
+ if (!offset) {
+ pr_err("%s: unsupported omap type\n", __func__);
+ return;
+ }
+
+ omap_ctrl_writel(bootaddr, offset);
+}
+
+/**
+ * omap_ctrl_write_dsp_boot_mode - set boot mode for a remote processor
+ * @bootmode: 8-bit value to pass to some boot code
+ *
+ * Sets boot mode for the boot loader of a supported processor
+ * when a power ON sequence occurs.
+ */
+void omap_ctrl_write_dsp_boot_mode(u8 bootmode)
+{
+ u32 offset = cpu_is_omap243x() ? OMAP243X_CONTROL_IVA2_BOOTMOD :
+ cpu_is_omap34xx() ? OMAP343X_CONTROL_IVA2_BOOTMOD :
+ 0;
+
+ if (!offset) {
+ pr_err("%s: unsupported omap type\n", __func__);
+ return;
+ }
+
+ omap_ctrl_writel(bootmode, offset);
+}
+
#if defined(CONFIG_ARCH_OMAP3) && defined(CONFIG_PM)
/*
* Clears the scratchpad contents in case of cold boot-
extern void omap3_control_save_context(void);
extern void omap3_control_restore_context(void);
extern void omap3_ctrl_write_boot_mode(u8 bootmode);
+extern void omap_ctrl_write_dsp_boot_addr(u32 bootaddr);
+extern void omap_ctrl_write_dsp_boot_mode(u8 bootmode);
extern void omap3630_ctrl_disable_rta(void);
extern int omap3_ctrl_save_padconf(void);
#else
#include <asm/memblock.h>
+#include "control.h"
#include "cm2xxx_3xxx.h"
#include "prm2xxx_3xxx.h"
#ifdef CONFIG_BRIDGE_DVFS
.dsp_cm_read = omap2_cm_read_mod_reg,
.dsp_cm_write = omap2_cm_write_mod_reg,
.dsp_cm_rmw_bits = omap2_cm_rmw_mod_reg_bits,
+
+ .set_bootaddr = omap_ctrl_write_dsp_boot_addr,
+ .set_bootmode = omap_ctrl_write_dsp_boot_mode,
};
static phys_addr_t omap_dsp_phys_mempool_base;
#define OMAP4_CTRL_MODULE_CORE_STD_FUSE_OPP_DPLL_1 0x0268
#define OMAP4_CTRL_MODULE_CORE_STATUS 0x02c4
#define OMAP4_CTRL_MODULE_CORE_DEV_CONF 0x0300
+#define OMAP4_CTRL_MODULE_CORE_DSP_BOOTADDR 0x0304
#define OMAP4_CTRL_MODULE_CORE_LDOVBB_IVA_VOLTAGE_CTRL 0x0314
#define OMAP4_CTRL_MODULE_CORE_LDOVBB_MPU_VOLTAGE_CTRL 0x0318
#define OMAP4_CTRL_MODULE_CORE_LDOSRAM_IVA_VOLTAGE_CTRL 0x0320
*/
#define LINKS_PER_OCP_IF 2
+/**
+ * struct omap_hwmod_soc_ops - fn ptrs for some SoC-specific operations
+ * @enable_module: function to enable a module (via MODULEMODE)
+ * @disable_module: function to disable a module (via MODULEMODE)
+ *
+ * XXX Eventually this functionality will be hidden inside the PRM/CM
+ * device drivers. Until then, this should avoid huge blocks of cpu_is_*()
+ * conditionals in this code.
+ */
+struct omap_hwmod_soc_ops {
+ void (*enable_module)(struct omap_hwmod *oh);
+ int (*disable_module)(struct omap_hwmod *oh);
+ int (*wait_target_ready)(struct omap_hwmod *oh);
+ int (*assert_hardreset)(struct omap_hwmod *oh,
+ struct omap_hwmod_rst_info *ohri);
+ int (*deassert_hardreset)(struct omap_hwmod *oh,
+ struct omap_hwmod_rst_info *ohri);
+ int (*is_hardreset_asserted)(struct omap_hwmod *oh,
+ struct omap_hwmod_rst_info *ohri);
+ int (*init_clkdm)(struct omap_hwmod *oh);
+};
+
+/* soc_ops: adapts the omap_hwmod code to the currently-booted SoC */
+static struct omap_hwmod_soc_ops soc_ops;
+
/* omap_hwmod_list contains all registered struct omap_hwmods */
static LIST_HEAD(omap_hwmod_list);
*/
static unsigned short free_ls, max_ls, ls_supp;
+/* inited: set to true once the hwmod code is initialized */
+static bool inited;
+
/* Private functions */
/**
}
/**
- * _enable_module - enable CLKCTRL modulemode on OMAP4
+ * _omap4_enable_module - enable CLKCTRL modulemode on OMAP4
* @oh: struct omap_hwmod *
*
* Enables the PRCM module mode related to the hwmod @oh.
* No return value.
*/
-static void _enable_module(struct omap_hwmod *oh)
+static void _omap4_enable_module(struct omap_hwmod *oh)
{
- /* The module mode does not exist prior OMAP4 */
- if (cpu_is_omap24xx() || cpu_is_omap34xx())
- return;
-
if (!oh->clkdm || !oh->prcm.omap4.modulemode)
return;
- pr_debug("omap_hwmod: %s: _enable_module: %d\n",
- oh->name, oh->prcm.omap4.modulemode);
+ pr_debug("omap_hwmod: %s: %s: %d\n",
+ oh->name, __func__, oh->prcm.omap4.modulemode);
omap4_cminst_module_enable(oh->prcm.omap4.modulemode,
oh->clkdm->prcm_partition,
*/
static int _omap4_wait_target_disable(struct omap_hwmod *oh)
{
- if (!cpu_is_omap44xx())
- return 0;
-
- if (!oh)
+ if (!oh || !oh->clkdm)
return -EINVAL;
if (oh->_int_flags & _HWMOD_NO_MPU_PORT)
return oh;
}
+
/**
* _init_clkdm - look up a clockdomain name, store pointer in omap_hwmod
* @oh: struct omap_hwmod *
*
* Convert a clockdomain name stored in a struct omap_hwmod into a
* clockdomain pointer, and save it into the struct omap_hwmod.
- * return -EINVAL if clkdm_name does not exist or if the lookup failed.
+ * Return -EINVAL if the clkdm_name lookup failed.
*/
static int _init_clkdm(struct omap_hwmod *oh)
{
- if (cpu_is_omap24xx() || cpu_is_omap34xx())
+ if (!oh->clkdm_name)
return 0;
- if (!oh->clkdm_name) {
- pr_warning("omap_hwmod: %s: no clkdm_name\n", oh->name);
- return -EINVAL;
- }
-
oh->clkdm = clkdm_lookup(oh->clkdm_name);
if (!oh->clkdm) {
pr_warning("omap_hwmod: %s: could not associate to clkdm %s\n",
ret |= _init_main_clk(oh);
ret |= _init_interface_clks(oh);
ret |= _init_opt_clks(oh);
- ret |= _init_clkdm(oh);
+ if (soc_ops.init_clkdm)
+ ret |= soc_ops.init_clkdm(oh);
if (!ret)
oh->_state = _HWMOD_STATE_CLKS_INITED;
return ret;
}
-/**
- * _wait_target_ready - wait for a module to leave slave idle
- * @oh: struct omap_hwmod *
- *
- * Wait for a module @oh to leave slave idle. Returns 0 if the module
- * does not have an IDLEST bit or if the module successfully leaves
- * slave idle; otherwise, pass along the return value of the
- * appropriate *_cm*_wait_module_ready() function.
- */
-static int _wait_target_ready(struct omap_hwmod *oh)
-{
- struct omap_hwmod_ocp_if *os;
- int ret;
-
- if (!oh)
- return -EINVAL;
-
- if (oh->flags & HWMOD_NO_IDLEST)
- return 0;
-
- os = _find_mpu_rt_port(oh);
- if (!os)
- return 0;
-
- /* XXX check module SIDLEMODE */
-
- /* XXX check clock enable states */
-
- if (cpu_is_omap24xx() || cpu_is_omap34xx()) {
- ret = omap2_cm_wait_module_ready(oh->prcm.omap2.module_offs,
- oh->prcm.omap2.idlest_reg_id,
- oh->prcm.omap2.idlest_idle_bit);
- } else if (cpu_is_omap44xx()) {
- if (!oh->clkdm)
- return -EINVAL;
-
- ret = omap4_cminst_wait_module_ready(oh->clkdm->prcm_partition,
- oh->clkdm->cm_inst,
- oh->clkdm->clkdm_offs,
- oh->prcm.omap4.clkctrl_offs);
- } else {
- BUG();
- };
-
- return ret;
-}
-
/**
* _lookup_hardreset - fill register bit info for this hwmod/reset line
* @oh: struct omap_hwmod *
* @oh: struct omap_hwmod *
* @name: name of the reset line to lookup and assert
*
- * Some IP like dsp, ipu or iva contain processor that require
- * an HW reset line to be assert / deassert in order to enable fully
- * the IP.
+ * Some IP like dsp, ipu or iva contain processor that require an HW
+ * reset line to be assert / deassert in order to enable fully the IP.
+ * Returns -EINVAL if @oh is null, -ENOSYS if we have no way of
+ * asserting the hardreset line on the currently-booted SoC, or passes
+ * along the return value from _lookup_hardreset() or the SoC's
+ * assert_hardreset code.
*/
static int _assert_hardreset(struct omap_hwmod *oh, const char *name)
{
struct omap_hwmod_rst_info ohri;
- u8 ret;
+ u8 ret = -EINVAL;
if (!oh)
return -EINVAL;
+ if (!soc_ops.assert_hardreset)
+ return -ENOSYS;
+
ret = _lookup_hardreset(oh, name, &ohri);
if (IS_ERR_VALUE(ret))
return ret;
- if (cpu_is_omap24xx() || cpu_is_omap34xx())
- return omap2_prm_assert_hardreset(oh->prcm.omap2.module_offs,
- ohri.rst_shift);
- else if (cpu_is_omap44xx())
- return omap4_prminst_assert_hardreset(ohri.rst_shift,
- oh->clkdm->pwrdm.ptr->prcm_partition,
- oh->clkdm->pwrdm.ptr->prcm_offs,
- oh->prcm.omap4.rstctrl_offs);
- else
- return -EINVAL;
+ ret = soc_ops.assert_hardreset(oh, &ohri);
+
+ return ret;
}
/**
* @oh: struct omap_hwmod *
* @name: name of the reset line to look up and deassert
*
- * Some IP like dsp, ipu or iva contain processor that require
- * an HW reset line to be assert / deassert in order to enable fully
- * the IP.
+ * Some IP like dsp, ipu or iva contain processor that require an HW
+ * reset line to be assert / deassert in order to enable fully the IP.
+ * Returns -EINVAL if @oh is null, -ENOSYS if we have no way of
+ * deasserting the hardreset line on the currently-booted SoC, or passes
+ * along the return value from _lookup_hardreset() or the SoC's
+ * deassert_hardreset code.
*/
static int _deassert_hardreset(struct omap_hwmod *oh, const char *name)
{
struct omap_hwmod_rst_info ohri;
- int ret;
+ int ret = -EINVAL;
if (!oh)
return -EINVAL;
+ if (!soc_ops.deassert_hardreset)
+ return -ENOSYS;
+
ret = _lookup_hardreset(oh, name, &ohri);
if (IS_ERR_VALUE(ret))
return ret;
- if (cpu_is_omap24xx() || cpu_is_omap34xx()) {
- ret = omap2_prm_deassert_hardreset(oh->prcm.omap2.module_offs,
- ohri.rst_shift,
- ohri.st_shift);
- } else if (cpu_is_omap44xx()) {
- if (ohri.st_shift)
- pr_err("omap_hwmod: %s: %s: hwmod data error: OMAP4 does not support st_shift\n",
- oh->name, name);
- ret = omap4_prminst_deassert_hardreset(ohri.rst_shift,
- oh->clkdm->pwrdm.ptr->prcm_partition,
- oh->clkdm->pwrdm.ptr->prcm_offs,
- oh->prcm.omap4.rstctrl_offs);
- } else {
- return -EINVAL;
- }
-
+ ret = soc_ops.deassert_hardreset(oh, &ohri);
if (ret == -EBUSY)
pr_warning("omap_hwmod: %s: failed to hardreset\n", oh->name);
* @oh: struct omap_hwmod *
* @name: name of the reset line to look up and read
*
- * Return the state of the reset line.
+ * Return the state of the reset line. Returns -EINVAL if @oh is
+ * null, -ENOSYS if we have no way of reading the hardreset line
+ * status on the currently-booted SoC, or passes along the return
+ * value from _lookup_hardreset() or the SoC's is_hardreset_asserted
+ * code.
*/
static int _read_hardreset(struct omap_hwmod *oh, const char *name)
{
struct omap_hwmod_rst_info ohri;
- u8 ret;
+ u8 ret = -EINVAL;
if (!oh)
return -EINVAL;
+ if (!soc_ops.is_hardreset_asserted)
+ return -ENOSYS;
+
ret = _lookup_hardreset(oh, name, &ohri);
if (IS_ERR_VALUE(ret))
return ret;
- if (cpu_is_omap24xx() || cpu_is_omap34xx()) {
- return omap2_prm_is_hardreset_asserted(oh->prcm.omap2.module_offs,
- ohri.st_shift);
- } else if (cpu_is_omap44xx()) {
- return omap4_prminst_is_hardreset_asserted(ohri.rst_shift,
- oh->clkdm->pwrdm.ptr->prcm_partition,
- oh->clkdm->pwrdm.ptr->prcm_offs,
- oh->prcm.omap4.rstctrl_offs);
- } else {
- return -EINVAL;
- }
+ return soc_ops.is_hardreset_asserted(oh, &ohri);
}
/**
{
int v;
- /* The module mode does not exist prior OMAP4 */
- if (!cpu_is_omap44xx())
- return -EINVAL;
-
if (!oh->clkdm || !oh->prcm.omap4.modulemode)
return -EINVAL;
}
_enable_clocks(oh);
- _enable_module(oh);
+ if (soc_ops.enable_module)
+ soc_ops.enable_module(oh);
- r = _wait_target_ready(oh);
+ r = (soc_ops.wait_target_ready) ? soc_ops.wait_target_ready(oh) :
+ -EINVAL;
if (!r) {
/*
* Set the clockdomain to HW_AUTO only if the target is ready,
_idle_sysc(oh);
_del_initiator_dep(oh, mpu_oh);
- _omap4_disable_module(oh);
+ if (soc_ops.disable_module)
+ soc_ops.disable_module(oh);
/*
* The module must be in idle mode before disabling any parents
if (oh->_state == _HWMOD_STATE_ENABLED) {
_del_initiator_dep(oh, mpu_oh);
/* XXX what about the other system initiators here? dma, dsp */
- _omap4_disable_module(oh);
+ if (soc_ops.disable_module)
+ soc_ops.disable_module(oh);
_disable_clocks(oh);
if (oh->clkdm)
clkdm_hwmod_disable(oh->clkdm, oh);
return 0;
}
+/* Static functions intended only for use in soc_ops field function pointers */
+
+/**
+ * _omap2_wait_target_ready - wait for a module to leave slave idle
+ * @oh: struct omap_hwmod *
+ *
+ * Wait for a module @oh to leave slave idle. Returns 0 if the module
+ * does not have an IDLEST bit or if the module successfully leaves
+ * slave idle; otherwise, pass along the return value of the
+ * appropriate *_cm*_wait_module_ready() function.
+ */
+static int _omap2_wait_target_ready(struct omap_hwmod *oh)
+{
+ if (!oh)
+ return -EINVAL;
+
+ if (oh->flags & HWMOD_NO_IDLEST)
+ return 0;
+
+ if (!_find_mpu_rt_port(oh))
+ return 0;
+
+ /* XXX check module SIDLEMODE, hardreset status, enabled clocks */
+
+ return omap2_cm_wait_module_ready(oh->prcm.omap2.module_offs,
+ oh->prcm.omap2.idlest_reg_id,
+ oh->prcm.omap2.idlest_idle_bit);
+}
+
+/**
+ * _omap4_wait_target_ready - wait for a module to leave slave idle
+ * @oh: struct omap_hwmod *
+ *
+ * Wait for a module @oh to leave slave idle. Returns 0 if the module
+ * does not have an IDLEST bit or if the module successfully leaves
+ * slave idle; otherwise, pass along the return value of the
+ * appropriate *_cm*_wait_module_ready() function.
+ */
+static int _omap4_wait_target_ready(struct omap_hwmod *oh)
+{
+ if (!oh || !oh->clkdm)
+ return -EINVAL;
+
+ if (oh->flags & HWMOD_NO_IDLEST)
+ return 0;
+
+ if (!_find_mpu_rt_port(oh))
+ return 0;
+
+ /* XXX check module SIDLEMODE, hardreset status */
+
+ return omap4_cminst_wait_module_ready(oh->clkdm->prcm_partition,
+ oh->clkdm->cm_inst,
+ oh->clkdm->clkdm_offs,
+ oh->prcm.omap4.clkctrl_offs);
+}
+
+/**
+ * _omap2_assert_hardreset - call OMAP2 PRM hardreset fn with hwmod args
+ * @oh: struct omap_hwmod * to assert hardreset
+ * @ohri: hardreset line data
+ *
+ * Call omap2_prm_assert_hardreset() with parameters extracted from
+ * the hwmod @oh and the hardreset line data @ohri. Only intended for
+ * use as an soc_ops function pointer. Passes along the return value
+ * from omap2_prm_assert_hardreset(). XXX This function is scheduled
+ * for removal when the PRM code is moved into drivers/.
+ */
+static int _omap2_assert_hardreset(struct omap_hwmod *oh,
+ struct omap_hwmod_rst_info *ohri)
+{
+ return omap2_prm_assert_hardreset(oh->prcm.omap2.module_offs,
+ ohri->rst_shift);
+}
+
+/**
+ * _omap2_deassert_hardreset - call OMAP2 PRM hardreset fn with hwmod args
+ * @oh: struct omap_hwmod * to deassert hardreset
+ * @ohri: hardreset line data
+ *
+ * Call omap2_prm_deassert_hardreset() with parameters extracted from
+ * the hwmod @oh and the hardreset line data @ohri. Only intended for
+ * use as an soc_ops function pointer. Passes along the return value
+ * from omap2_prm_deassert_hardreset(). XXX This function is
+ * scheduled for removal when the PRM code is moved into drivers/.
+ */
+static int _omap2_deassert_hardreset(struct omap_hwmod *oh,
+ struct omap_hwmod_rst_info *ohri)
+{
+ return omap2_prm_deassert_hardreset(oh->prcm.omap2.module_offs,
+ ohri->rst_shift,
+ ohri->st_shift);
+}
+
+/**
+ * _omap2_is_hardreset_asserted - call OMAP2 PRM hardreset fn with hwmod args
+ * @oh: struct omap_hwmod * to test hardreset
+ * @ohri: hardreset line data
+ *
+ * Call omap2_prm_is_hardreset_asserted() with parameters extracted
+ * from the hwmod @oh and the hardreset line data @ohri. Only
+ * intended for use as an soc_ops function pointer. Passes along the
+ * return value from omap2_prm_is_hardreset_asserted(). XXX This
+ * function is scheduled for removal when the PRM code is moved into
+ * drivers/.
+ */
+static int _omap2_is_hardreset_asserted(struct omap_hwmod *oh,
+ struct omap_hwmod_rst_info *ohri)
+{
+ return omap2_prm_is_hardreset_asserted(oh->prcm.omap2.module_offs,
+ ohri->st_shift);
+}
+
+/**
+ * _omap4_assert_hardreset - call OMAP4 PRM hardreset fn with hwmod args
+ * @oh: struct omap_hwmod * to assert hardreset
+ * @ohri: hardreset line data
+ *
+ * Call omap4_prminst_assert_hardreset() with parameters extracted
+ * from the hwmod @oh and the hardreset line data @ohri. Only
+ * intended for use as an soc_ops function pointer. Passes along the
+ * return value from omap4_prminst_assert_hardreset(). XXX This
+ * function is scheduled for removal when the PRM code is moved into
+ * drivers/.
+ */
+static int _omap4_assert_hardreset(struct omap_hwmod *oh,
+ struct omap_hwmod_rst_info *ohri)
+{
+ if (!oh->clkdm)
+ return -EINVAL;
+
+ return omap4_prminst_assert_hardreset(ohri->rst_shift,
+ oh->clkdm->pwrdm.ptr->prcm_partition,
+ oh->clkdm->pwrdm.ptr->prcm_offs,
+ oh->prcm.omap4.rstctrl_offs);
+}
+
+/**
+ * _omap4_deassert_hardreset - call OMAP4 PRM hardreset fn with hwmod args
+ * @oh: struct omap_hwmod * to deassert hardreset
+ * @ohri: hardreset line data
+ *
+ * Call omap4_prminst_deassert_hardreset() with parameters extracted
+ * from the hwmod @oh and the hardreset line data @ohri. Only
+ * intended for use as an soc_ops function pointer. Passes along the
+ * return value from omap4_prminst_deassert_hardreset(). XXX This
+ * function is scheduled for removal when the PRM code is moved into
+ * drivers/.
+ */
+static int _omap4_deassert_hardreset(struct omap_hwmod *oh,
+ struct omap_hwmod_rst_info *ohri)
+{
+ if (!oh->clkdm)
+ return -EINVAL;
+
+ if (ohri->st_shift)
+ pr_err("omap_hwmod: %s: %s: hwmod data error: OMAP4 does not support st_shift\n",
+ oh->name, ohri->name);
+ return omap4_prminst_deassert_hardreset(ohri->rst_shift,
+ oh->clkdm->pwrdm.ptr->prcm_partition,
+ oh->clkdm->pwrdm.ptr->prcm_offs,
+ oh->prcm.omap4.rstctrl_offs);
+}
+
+/**
+ * _omap4_is_hardreset_asserted - call OMAP4 PRM hardreset fn with hwmod args
+ * @oh: struct omap_hwmod * to test hardreset
+ * @ohri: hardreset line data
+ *
+ * Call omap4_prminst_is_hardreset_asserted() with parameters
+ * extracted from the hwmod @oh and the hardreset line data @ohri.
+ * Only intended for use as an soc_ops function pointer. Passes along
+ * the return value from omap4_prminst_is_hardreset_asserted(). XXX
+ * This function is scheduled for removal when the PRM code is moved
+ * into drivers/.
+ */
+static int _omap4_is_hardreset_asserted(struct omap_hwmod *oh,
+ struct omap_hwmod_rst_info *ohri)
+{
+ if (!oh->clkdm)
+ return -EINVAL;
+
+ return omap4_prminst_is_hardreset_asserted(ohri->rst_shift,
+ oh->clkdm->pwrdm.ptr->prcm_partition,
+ oh->clkdm->pwrdm.ptr->prcm_offs,
+ oh->prcm.omap4.rstctrl_offs);
+}
+
/* Public functions */
u32 omap_hwmod_read(struct omap_hwmod *oh, u16 reg_offs)
*
* Intended to be called early in boot before the clock framework is
* initialized. If @ois is not null, will register all omap_hwmods
- * listed in @ois that are valid for this chip. Returns 0.
+ * listed in @ois that are valid for this chip. Returns -EINVAL if
+ * omap_hwmod_init() hasn't been called before calling this function,
+ * -ENOMEM if the link memory area can't be allocated, or 0 upon
+ * success.
*/
int __init omap_hwmod_register_links(struct omap_hwmod_ocp_if **ois)
{
int r, i;
+ if (!inited)
+ return -EINVAL;
+
if (!ois)
return 0;
return 0;
}
+
+/**
+ * omap_hwmod_init - initialize the hwmod code
+ *
+ * Sets up some function pointers needed by the hwmod code to operate on the
+ * currently-booted SoC. Intended to be called once during kernel init
+ * before any hwmods are registered. No return value.
+ */
+void __init omap_hwmod_init(void)
+{
+ if (cpu_is_omap24xx() || cpu_is_omap34xx()) {
+ soc_ops.wait_target_ready = _omap2_wait_target_ready;
+ soc_ops.assert_hardreset = _omap2_assert_hardreset;
+ soc_ops.deassert_hardreset = _omap2_deassert_hardreset;
+ soc_ops.is_hardreset_asserted = _omap2_is_hardreset_asserted;
+ } else if (cpu_is_omap44xx()) {
+ soc_ops.enable_module = _omap4_enable_module;
+ soc_ops.disable_module = _omap4_disable_module;
+ soc_ops.wait_target_ready = _omap4_wait_target_ready;
+ soc_ops.assert_hardreset = _omap4_assert_hardreset;
+ soc_ops.deassert_hardreset = _omap4_deassert_hardreset;
+ soc_ops.is_hardreset_asserted = _omap4_is_hardreset_asserted;
+ soc_ops.init_clkdm = _init_clkdm;
+ } else {
+ WARN(1, "omap_hwmod: unknown SoC type\n");
+ }
+
+ inited = true;
+}
.name = "mcbsp",
};
+static struct omap_hwmod_opt_clk mcbsp_opt_clks[] = {
+ { .role = "pad_fck", .clk = "mcbsp_clks" },
+ { .role = "prcm_fck", .clk = "func_96m_ck" },
+};
+
/* mcbsp1 */
static struct omap_hwmod_irq_info omap2420_mcbsp1_irqs[] = {
{ .name = "tx", .irq = 59 },
.idlest_idle_bit = OMAP24XX_ST_MCBSP1_SHIFT,
},
},
+ .opt_clks = mcbsp_opt_clks,
+ .opt_clks_cnt = ARRAY_SIZE(mcbsp_opt_clks),
};
/* mcbsp2 */
.idlest_idle_bit = OMAP24XX_ST_MCBSP2_SHIFT,
},
},
+ .opt_clks = mcbsp_opt_clks,
+ .opt_clks_cnt = ARRAY_SIZE(mcbsp_opt_clks),
};
static struct omap_hwmod_class_sysconfig omap2420_msdi_sysc = {
int __init omap2420_hwmod_init(void)
{
+ omap_hwmod_init();
return omap_hwmod_register_links(omap2420_hwmod_ocp_ifs);
}
.rev = MCBSP_CONFIG_TYPE2,
};
+static struct omap_hwmod_opt_clk mcbsp_opt_clks[] = {
+ { .role = "pad_fck", .clk = "mcbsp_clks" },
+ { .role = "prcm_fck", .clk = "func_96m_ck" },
+};
+
/* mcbsp1 */
static struct omap_hwmod_irq_info omap2430_mcbsp1_irqs[] = {
{ .name = "tx", .irq = 59 },
.idlest_idle_bit = OMAP24XX_ST_MCBSP1_SHIFT,
},
},
+ .opt_clks = mcbsp_opt_clks,
+ .opt_clks_cnt = ARRAY_SIZE(mcbsp_opt_clks),
};
/* mcbsp2 */
.idlest_idle_bit = OMAP24XX_ST_MCBSP2_SHIFT,
},
},
+ .opt_clks = mcbsp_opt_clks,
+ .opt_clks_cnt = ARRAY_SIZE(mcbsp_opt_clks),
};
/* mcbsp3 */
.idlest_idle_bit = OMAP2430_ST_MCBSP3_SHIFT,
},
},
+ .opt_clks = mcbsp_opt_clks,
+ .opt_clks_cnt = ARRAY_SIZE(mcbsp_opt_clks),
};
/* mcbsp4 */
.idlest_idle_bit = OMAP2430_ST_MCBSP4_SHIFT,
},
},
+ .opt_clks = mcbsp_opt_clks,
+ .opt_clks_cnt = ARRAY_SIZE(mcbsp_opt_clks),
};
/* mcbsp5 */
.idlest_idle_bit = OMAP2430_ST_MCBSP5_SHIFT,
},
},
+ .opt_clks = mcbsp_opt_clks,
+ .opt_clks_cnt = ARRAY_SIZE(mcbsp_opt_clks),
};
/* MMC/SD/SDIO common */
int __init omap2430_hwmod_init(void)
{
+ omap_hwmod_init();
return omap_hwmod_register_links(omap2430_hwmod_ocp_ifs);
}
.rev = MCBSP_CONFIG_TYPE3,
};
+/* McBSP functional clock mapping */
+static struct omap_hwmod_opt_clk mcbsp15_opt_clks[] = {
+ { .role = "pad_fck", .clk = "mcbsp_clks" },
+ { .role = "prcm_fck", .clk = "core_96m_fck" },
+};
+
+static struct omap_hwmod_opt_clk mcbsp234_opt_clks[] = {
+ { .role = "pad_fck", .clk = "mcbsp_clks" },
+ { .role = "prcm_fck", .clk = "per_96m_fck" },
+};
+
/* mcbsp1 */
static struct omap_hwmod_irq_info omap3xxx_mcbsp1_irqs[] = {
{ .name = "common", .irq = 16 },
.idlest_idle_bit = OMAP3430_ST_MCBSP1_SHIFT,
},
},
+ .opt_clks = mcbsp15_opt_clks,
+ .opt_clks_cnt = ARRAY_SIZE(mcbsp15_opt_clks),
};
/* mcbsp2 */
.idlest_idle_bit = OMAP3430_ST_MCBSP2_SHIFT,
},
},
+ .opt_clks = mcbsp234_opt_clks,
+ .opt_clks_cnt = ARRAY_SIZE(mcbsp234_opt_clks),
.dev_attr = &omap34xx_mcbsp2_dev_attr,
};
.idlest_idle_bit = OMAP3430_ST_MCBSP3_SHIFT,
},
},
+ .opt_clks = mcbsp234_opt_clks,
+ .opt_clks_cnt = ARRAY_SIZE(mcbsp234_opt_clks),
.dev_attr = &omap34xx_mcbsp3_dev_attr,
};
.idlest_idle_bit = OMAP3430_ST_MCBSP4_SHIFT,
},
},
+ .opt_clks = mcbsp234_opt_clks,
+ .opt_clks_cnt = ARRAY_SIZE(mcbsp234_opt_clks),
};
/* mcbsp5 */
.idlest_idle_bit = OMAP3430_ST_MCBSP5_SHIFT,
},
},
+ .opt_clks = mcbsp15_opt_clks,
+ .opt_clks_cnt = ARRAY_SIZE(mcbsp15_opt_clks),
};
/* 'mcbsp sidetone' class */
struct omap_hwmod_ocp_if **h = NULL;
unsigned int rev;
+ omap_hwmod_init();
+
/* Register hwmod links common to all OMAP3 */
r = omap_hwmod_register_links(omap3xxx_hwmod_ocp_ifs);
if (r < 0)
static struct omap_hwmod omap44xx_cm_core_aon_hwmod = {
.name = "cm_core_aon",
.class = &omap44xx_prcm_hwmod_class,
- .clkdm_name = "cm_clkdm",
};
/* cm_core */
static struct omap_hwmod omap44xx_cm_core_hwmod = {
.name = "cm_core",
.class = &omap44xx_prcm_hwmod_class,
- .clkdm_name = "cm_clkdm",
};
/* prm */
static struct omap_hwmod omap44xx_prm_hwmod = {
.name = "prm",
.class = &omap44xx_prcm_hwmod_class,
- .clkdm_name = "prm_clkdm",
.mpu_irqs = omap44xx_prm_irqs,
.rst_lines = omap44xx_prm_resets,
.rst_lines_cnt = ARRAY_SIZE(omap44xx_prm_resets),
int __init omap44xx_hwmod_init(void)
{
+ omap_hwmod_init();
return omap_hwmod_register_links(omap44xx_hwmod_ocp_ifs);
}
+++ /dev/null
-/*
- * Platform level USB initialization for FS USB OTG controller on omap1 and 24xx
- *
- * Copyright (C) 2004 Texas Instruments, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/errno.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/clk.h>
-#include <linux/err.h>
-
-#include <asm/irq.h>
-
-#include <plat/usb.h>
-#include <plat/board.h>
-
-#include "control.h"
-#include "mux.h"
-
-#define INT_USB_IRQ_GEN INT_24XX_USB_IRQ_GEN
-#define INT_USB_IRQ_NISO INT_24XX_USB_IRQ_NISO
-#define INT_USB_IRQ_ISO INT_24XX_USB_IRQ_ISO
-#define INT_USB_IRQ_HGEN INT_24XX_USB_IRQ_HGEN
-#define INT_USB_IRQ_OTG INT_24XX_USB_IRQ_OTG
-
-#if defined(CONFIG_ARCH_OMAP2)
-
-#ifdef CONFIG_USB_GADGET_OMAP
-
-static struct resource udc_resources[] = {
- /* order is significant! */
- { /* registers */
- .start = UDC_BASE,
- .end = UDC_BASE + 0xff,
- .flags = IORESOURCE_MEM,
- }, { /* general IRQ */
- .start = INT_USB_IRQ_GEN,
- .flags = IORESOURCE_IRQ,
- }, { /* PIO IRQ */
- .start = INT_USB_IRQ_NISO,
- .flags = IORESOURCE_IRQ,
- }, { /* SOF IRQ */
- .start = INT_USB_IRQ_ISO,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static u64 udc_dmamask = ~(u32)0;
-
-static struct platform_device udc_device = {
- .name = "omap_udc",
- .id = -1,
- .dev = {
- .dma_mask = &udc_dmamask,
- .coherent_dma_mask = 0xffffffff,
- },
- .num_resources = ARRAY_SIZE(udc_resources),
- .resource = udc_resources,
-};
-
-static inline void udc_device_init(struct omap_usb_config *pdata)
-{
- pdata->udc_device = &udc_device;
-}
-
-#else
-
-static inline void udc_device_init(struct omap_usb_config *pdata)
-{
-}
-
-#endif
-
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
-
-/* The dmamask must be set for OHCI to work */
-static u64 ohci_dmamask = ~(u32)0;
-
-static struct resource ohci_resources[] = {
- {
- .start = OMAP_OHCI_BASE,
- .end = OMAP_OHCI_BASE + 0xff,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = INT_USB_IRQ_HGEN,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device ohci_device = {
- .name = "ohci",
- .id = -1,
- .dev = {
- .dma_mask = &ohci_dmamask,
- .coherent_dma_mask = 0xffffffff,
- },
- .num_resources = ARRAY_SIZE(ohci_resources),
- .resource = ohci_resources,
-};
-
-static inline void ohci_device_init(struct omap_usb_config *pdata)
-{
- pdata->ohci_device = &ohci_device;
-}
-
-#else
-
-static inline void ohci_device_init(struct omap_usb_config *pdata)
-{
-}
-
-#endif
-
-#if defined(CONFIG_USB_OTG) && defined(CONFIG_ARCH_OMAP_OTG)
-
-static struct resource otg_resources[] = {
- /* order is significant! */
- {
- .start = OTG_BASE,
- .end = OTG_BASE + 0xff,
- .flags = IORESOURCE_MEM,
- }, {
- .start = INT_USB_IRQ_OTG,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device otg_device = {
- .name = "omap_otg",
- .id = -1,
- .num_resources = ARRAY_SIZE(otg_resources),
- .resource = otg_resources,
-};
-
-static inline void otg_device_init(struct omap_usb_config *pdata)
-{
- pdata->otg_device = &otg_device;
-}
-
-#else
-
-static inline void otg_device_init(struct omap_usb_config *pdata)
-{
-}
-
-#endif
-
-static void omap2_usb_devconf_clear(u8 port, u32 mask)
-{
- u32 r;
-
- r = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0);
- r &= ~USBTXWRMODEI(port, mask);
- omap_ctrl_writel(r, OMAP2_CONTROL_DEVCONF0);
-}
-
-static void omap2_usb_devconf_set(u8 port, u32 mask)
-{
- u32 r;
-
- r = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0);
- r |= USBTXWRMODEI(port, mask);
- omap_ctrl_writel(r, OMAP2_CONTROL_DEVCONF0);
-}
-
-static void omap2_usb2_disable_5pinbitll(void)
-{
- u32 r;
-
- r = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0);
- r &= ~(USBTXWRMODEI(2, USB_BIDIR_TLL) | USBT2TLL5PI);
- omap_ctrl_writel(r, OMAP2_CONTROL_DEVCONF0);
-}
-
-static void omap2_usb2_enable_5pinunitll(void)
-{
- u32 r;
-
- r = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0);
- r |= USBTXWRMODEI(2, USB_UNIDIR_TLL) | USBT2TLL5PI;
- omap_ctrl_writel(r, OMAP2_CONTROL_DEVCONF0);
-}
-
-static u32 __init omap2_usb0_init(unsigned nwires, unsigned is_device)
-{
- u32 syscon1 = 0;
-
- omap2_usb_devconf_clear(0, USB_BIDIR_TLL);
-
- if (nwires == 0)
- return 0;
-
- if (is_device)
- omap_mux_init_signal("usb0_puen", 0);
-
- omap_mux_init_signal("usb0_dat", 0);
- omap_mux_init_signal("usb0_txen", 0);
- omap_mux_init_signal("usb0_se0", 0);
- if (nwires != 3)
- omap_mux_init_signal("usb0_rcv", 0);
-
- switch (nwires) {
- case 3:
- syscon1 = 2;
- omap2_usb_devconf_set(0, USB_BIDIR);
- break;
- case 4:
- syscon1 = 1;
- omap2_usb_devconf_set(0, USB_BIDIR);
- break;
- case 6:
- syscon1 = 3;
- omap_mux_init_signal("usb0_vp", 0);
- omap_mux_init_signal("usb0_vm", 0);
- omap2_usb_devconf_set(0, USB_UNIDIR);
- break;
- default:
- printk(KERN_ERR "illegal usb%d %d-wire transceiver\n",
- 0, nwires);
- }
-
- return syscon1 << 16;
-}
-
-static u32 __init omap2_usb1_init(unsigned nwires)
-{
- u32 syscon1 = 0;
-
- omap2_usb_devconf_clear(1, USB_BIDIR_TLL);
-
- if (nwires == 0)
- return 0;
-
- /* NOTE: board-specific code must set up pin muxing for usb1,
- * since each signal could come out on either of two balls.
- */
-
- switch (nwires) {
- case 2:
- /* NOTE: board-specific code must override this setting if
- * this TLL link is not using DP/DM
- */
- syscon1 = 1;
- omap2_usb_devconf_set(1, USB_BIDIR_TLL);
- break;
- case 3:
- syscon1 = 2;
- omap2_usb_devconf_set(1, USB_BIDIR);
- break;
- case 4:
- syscon1 = 1;
- omap2_usb_devconf_set(1, USB_BIDIR);
- break;
- case 6:
- default:
- printk(KERN_ERR "illegal usb%d %d-wire transceiver\n",
- 1, nwires);
- }
-
- return syscon1 << 20;
-}
-
-static u32 __init omap2_usb2_init(unsigned nwires, unsigned alt_pingroup)
-{
- u32 syscon1 = 0;
-
- omap2_usb2_disable_5pinbitll();
- alt_pingroup = 0;
-
- /* NOTE omap1 erratum: must leave USB2_UNI_R set if usb0 in use */
- if (alt_pingroup || nwires == 0)
- return 0;
-
- omap_mux_init_signal("usb2_dat", 0);
- omap_mux_init_signal("usb2_se0", 0);
- if (nwires > 2)
- omap_mux_init_signal("usb2_txen", 0);
- if (nwires > 3)
- omap_mux_init_signal("usb2_rcv", 0);
-
- switch (nwires) {
- case 2:
- /* NOTE: board-specific code must override this setting if
- * this TLL link is not using DP/DM
- */
- syscon1 = 1;
- omap2_usb_devconf_set(2, USB_BIDIR_TLL);
- break;
- case 3:
- syscon1 = 2;
- omap2_usb_devconf_set(2, USB_BIDIR);
- break;
- case 4:
- syscon1 = 1;
- omap2_usb_devconf_set(2, USB_BIDIR);
- break;
- case 5:
- /* NOTE: board-specific code must mux this setting depending
- * on TLL link using DP/DM. Something must also
- * set up OTG_SYSCON2.HMC_TLL{ATTACH,SPEED}
- * 2420: hdq_sio.usb2_tllse0 or vlynq_rx0.usb2_tllse0
- * 2430: hdq_sio.usb2_tllse0 or sdmmc2_dat0.usb2_tllse0
- */
-
- syscon1 = 3;
- omap2_usb2_enable_5pinunitll();
- break;
- case 6:
- default:
- printk(KERN_ERR "illegal usb%d %d-wire transceiver\n",
- 2, nwires);
- }
-
- return syscon1 << 24;
-}
-
-void __init omap2_usbfs_init(struct omap_usb_config *pdata)
-{
- struct clk *ick;
-
- if (!cpu_is_omap24xx())
- return;
-
- ick = clk_get(NULL, "usb_l4_ick");
- if (IS_ERR(ick))
- return;
-
- clk_enable(ick);
- pdata->usb0_init = omap2_usb0_init;
- pdata->usb1_init = omap2_usb1_init;
- pdata->usb2_init = omap2_usb2_init;
- udc_device_init(pdata);
- ohci_device_init(pdata);
- otg_device_init(pdata);
- omap_otg_init(pdata);
- clk_disable(ick);
- clk_put(ick);
-}
-
-#endif
# Common support
obj-y := common.o sram.o clock.o devices.o dma.o mux.o \
- usb.o fb.o counter_32k.o
+ fb.o counter_32k.o
obj-m :=
obj-n :=
obj- :=
static inline void omap_enable_channel_irq(int lch)
{
- u32 status;
-
/* Clear CSR */
if (cpu_class_is_omap1())
- status = p->dma_read(CSR, lch);
- else if (cpu_class_is_omap2())
+ p->dma_read(CSR, lch);
+ else
p->dma_write(OMAP2_DMA_CSR_CLEAR_MASK, CSR, lch);
/* Enable some nice interrupts. */
p->dma_write(dma_chan[lch].enabled_irqs, CICR, lch);
}
-static void omap_disable_channel_irq(int lch)
+static inline void omap_disable_channel_irq(int lch)
{
- if (cpu_class_is_omap2())
- p->dma_write(0, CICR, lch);
+ /* disable channel interrupts */
+ p->dma_write(0, CICR, lch);
+ /* Clear CSR */
+ if (cpu_class_is_omap1())
+ p->dma_read(CSR, lch);
+ else
+ p->dma_write(OMAP2_DMA_CSR_CLEAR_MASK, CSR, lch);
}
void omap_enable_dma_irq(int lch, u16 bits)
l = p->dma_read(CLNK_CTRL, lch);
/* Disable interrupts */
+ omap_disable_channel_irq(lch);
+
if (cpu_class_is_omap1()) {
- p->dma_write(0, CICR, lch);
/* Set the STOP_LNK bit */
l |= 1 << 14;
}
if (cpu_class_is_omap2()) {
- omap_disable_channel_irq(lch);
/* Clear the ENABLE_LNK bit */
l &= ~(1 << 15);
}
return;
spin_lock_irqsave(&dma_chan_lock, flags);
+ /* clear IRQ STATUS */
+ p->dma_write(1 << lch, IRQSTATUS_L0, lch);
+ /* Enable interrupt */
val = p->dma_read(IRQENABLE_L0, lch);
val |= 1 << lch;
p->dma_write(val, IRQENABLE_L0, lch);
return;
spin_lock_irqsave(&dma_chan_lock, flags);
+ /* Disable interrupt */
val = p->dma_read(IRQENABLE_L0, lch);
val &= ~(1 << lch);
p->dma_write(val, IRQENABLE_L0, lch);
+ /* clear IRQ STATUS */
+ p->dma_write(1 << lch, IRQSTATUS_L0, lch);
spin_unlock_irqrestore(&dma_chan_lock, flags);
}
}
if (cpu_class_is_omap2()) {
- omap2_enable_irq_lch(free_ch);
omap_enable_channel_irq(free_ch);
- /* Clear the CSR register and IRQ status register */
- p->dma_write(OMAP2_DMA_CSR_CLEAR_MASK, CSR, free_ch);
- p->dma_write(1 << free_ch, IRQSTATUS_L0, 0);
+ omap2_enable_irq_lch(free_ch);
}
*dma_ch_out = free_ch;
return;
}
- if (cpu_class_is_omap1()) {
- /* Disable all DMA interrupts for the channel. */
- p->dma_write(0, CICR, lch);
- /* Make sure the DMA transfer is stopped. */
- p->dma_write(0, CCR, lch);
- }
-
- if (cpu_class_is_omap2()) {
+ /* Disable interrupt for logical channel */
+ if (cpu_class_is_omap2())
omap2_disable_irq_lch(lch);
- /* Clear the CSR register and IRQ status register */
- p->dma_write(OMAP2_DMA_CSR_CLEAR_MASK, CSR, lch);
- p->dma_write(1 << lch, IRQSTATUS_L0, lch);
+ /* Disable all DMA interrupts for the channel. */
+ omap_disable_channel_irq(lch);
- /* Disable all DMA interrupts for the channel. */
- p->dma_write(0, CICR, lch);
+ /* Make sure the DMA transfer is stopped. */
+ p->dma_write(0, CCR, lch);
- /* Make sure the DMA transfer is stopped. */
- p->dma_write(0, CCR, lch);
+ /* Clear registers */
+ if (cpu_class_is_omap2())
omap_clear_dma(lch);
- }
spin_lock_irqsave(&dma_chan_lock, flags);
dma_chan[lch].dev_id = -1;
u32 l;
/* Disable all interrupts on the channel */
- if (cpu_class_is_omap1())
- p->dma_write(0, CICR, lch);
+ omap_disable_channel_irq(lch);
l = p->dma_read(CCR, lch);
if (IS_DMA_ERRATA(DMA_ERRATA_i541) &&
int (*power_off)(void * data);
};
-struct omap_usb_config {
- /* Configure drivers according to the connectors on your board:
- * - "A" connector (rectagular)
- * ... for host/OHCI use, set "register_host".
- * - "B" connector (squarish) or "Mini-B"
- * ... for device/gadget use, set "register_dev".
- * - "Mini-AB" connector (very similar to Mini-B)
- * ... for OTG use as device OR host, initialize "otg"
- */
- unsigned register_host:1;
- unsigned register_dev:1;
- u8 otg; /* port number, 1-based: usb1 == 2 */
-
- u8 hmc_mode;
-
- /* implicitly true if otg: host supports remote wakeup? */
- u8 rwc;
-
- /* signaling pins used to talk to transceiver on usbN:
- * 0 == usbN unused
- * 2 == usb0-only, using internal transceiver
- * 3 == 3 wire bidirectional
- * 4 == 4 wire bidirectional
- * 6 == 6 wire unidirectional (or TLL)
- */
- u8 pins[3];
-
- struct platform_device *udc_device;
- struct platform_device *ohci_device;
- struct platform_device *otg_device;
-
- u32 (*usb0_init)(unsigned nwires, unsigned is_device);
- u32 (*usb1_init)(unsigned nwires);
- u32 (*usb2_init)(unsigned nwires, unsigned alt_pingroup);
-
- int (*ocpi_enable)(void);
-};
-
struct omap_lcd_config {
char panel_name[16];
char ctrl_name[16];
u8 min_divider;
u16 max_divider;
u8 modes;
-#if defined(CONFIG_ARCH_OMAP3) || defined(CONFIG_ARCH_OMAP4)
void __iomem *autoidle_reg;
void __iomem *idlest_reg;
u32 autoidle_mask;
u8 auto_recal_bit;
u8 recal_en_bit;
u8 recal_st_bit;
-# endif
u8 flags;
};
u32 (*dsp_cm_read)(s16 , u16);
u32 (*dsp_cm_rmw_bits)(u32, u32, s16, s16);
+ void (*set_bootaddr)(u32);
+ void (*set_bootmode)(u8);
+
phys_addr_t phys_mempool_base;
phys_addr_t phys_mempool_size;
};
int omap_hwmod_pad_route_irq(struct omap_hwmod *oh, int pad_idx, int irq_idx);
+extern void __init omap_hwmod_init(void);
+
/*
* Chip variant-specific hwmod init routines - XXX should be converted
* to use initcalls once the initial boot ordering is straightened out
struct regulator *regulator[OMAP3_HS_USB_PORTS];
};
+#ifdef CONFIG_ARCH_OMAP2PLUS
+
struct ehci_hcd_omap_platform_data {
enum usbhs_omap_port_mode port_mode[OMAP3_HS_USB_PORTS];
int reset_gpio_port[OMAP3_HS_USB_PORTS];
};
/*-------------------------------------------------------------------------*/
-#define OMAP1_OTG_BASE 0xfffb0400
-#define OMAP1_UDC_BASE 0xfffb4000
-#define OMAP1_OHCI_BASE 0xfffba000
-
-#define OMAP2_OHCI_BASE 0x4805e000
-#define OMAP2_UDC_BASE 0x4805e200
-#define OMAP2_OTG_BASE 0x4805e300
-
-#ifdef CONFIG_ARCH_OMAP1
-
-#define OTG_BASE OMAP1_OTG_BASE
-#define UDC_BASE OMAP1_UDC_BASE
-#define OMAP_OHCI_BASE OMAP1_OHCI_BASE
-
-#else
-
-#define OTG_BASE OMAP2_OTG_BASE
-#define UDC_BASE OMAP2_UDC_BASE
-#define OMAP_OHCI_BASE OMAP2_OHCI_BASE
-
struct omap_musb_board_data {
u8 interface_type;
u8 mode;
extern int omap4430_phy_exit(struct device *dev);
extern int omap4430_phy_suspend(struct device *dev, int suspend);
-/*
- * NOTE: Please update omap USB drivers to use ioremap + read/write
- */
-
-#define OMAP2_L4_IO_OFFSET 0xb2000000
-#define OMAP2_L4_IO_ADDRESS(pa) IOMEM((pa) + OMAP2_L4_IO_OFFSET)
-
-static inline u8 omap_readb(u32 pa)
-{
- return __raw_readb(OMAP2_L4_IO_ADDRESS(pa));
-}
-
-static inline u16 omap_readw(u32 pa)
-{
- return __raw_readw(OMAP2_L4_IO_ADDRESS(pa));
-}
-
-static inline u32 omap_readl(u32 pa)
-{
- return __raw_readl(OMAP2_L4_IO_ADDRESS(pa));
-}
-
-static inline void omap_writeb(u8 v, u32 pa)
-{
- __raw_writeb(v, OMAP2_L4_IO_ADDRESS(pa));
-}
-
-
-static inline void omap_writew(u16 v, u32 pa)
-{
- __raw_writew(v, OMAP2_L4_IO_ADDRESS(pa));
-}
-
-static inline void omap_writel(u32 v, u32 pa)
-{
- __raw_writel(v, OMAP2_L4_IO_ADDRESS(pa));
-}
-
#endif
extern void am35x_musb_reset(void);
extern void am35x_set_mode(u8 musb_mode);
extern void ti81xx_musb_phy_power(u8 on);
-/*
- * FIXME correct answer depends on hmc_mode,
- * as does (on omap1) any nonzero value for config->otg port number
- */
-#ifdef CONFIG_USB_GADGET_OMAP
-#define is_usb0_device(config) 1
-#else
-#define is_usb0_device(config) 0
-#endif
-
-void omap_otg_init(struct omap_usb_config *config);
-
-#if defined(CONFIG_USB) || defined(CONFIG_USB_MODULE)
-void omap1_usb_init(struct omap_usb_config *pdata);
-#else
-static inline void omap1_usb_init(struct omap_usb_config *pdata)
-{
-}
-#endif
-
-#if defined(CONFIG_ARCH_OMAP_OTG) || defined(CONFIG_ARCH_OMAP_OTG_MODULE)
-void omap2_usbfs_init(struct omap_usb_config *pdata);
-#else
-static inline void omap2_usbfs_init(struct omap_usb_config *pdata)
-{
-}
-#endif
-
-/*-------------------------------------------------------------------------*/
-
-/*
- * OTG and transceiver registers, for OMAPs starting with ARM926
- */
-#define OTG_REV (OTG_BASE + 0x00)
-#define OTG_SYSCON_1 (OTG_BASE + 0x04)
-# define USB2_TRX_MODE(w) (((w)>>24)&0x07)
-# define USB1_TRX_MODE(w) (((w)>>20)&0x07)
-# define USB0_TRX_MODE(w) (((w)>>16)&0x07)
-# define OTG_IDLE_EN (1 << 15)
-# define HST_IDLE_EN (1 << 14)
-# define DEV_IDLE_EN (1 << 13)
-# define OTG_RESET_DONE (1 << 2)
-# define OTG_SOFT_RESET (1 << 1)
-#define OTG_SYSCON_2 (OTG_BASE + 0x08)
-# define OTG_EN (1 << 31)
-# define USBX_SYNCHRO (1 << 30)
-# define OTG_MST16 (1 << 29)
-# define SRP_GPDATA (1 << 28)
-# define SRP_GPDVBUS (1 << 27)
-# define SRP_GPUVBUS(w) (((w)>>24)&0x07)
-# define A_WAIT_VRISE(w) (((w)>>20)&0x07)
-# define B_ASE_BRST(w) (((w)>>16)&0x07)
-# define SRP_DPW (1 << 14)
-# define SRP_DATA (1 << 13)
-# define SRP_VBUS (1 << 12)
-# define OTG_PADEN (1 << 10)
-# define HMC_PADEN (1 << 9)
-# define UHOST_EN (1 << 8)
-# define HMC_TLLSPEED (1 << 7)
-# define HMC_TLLATTACH (1 << 6)
-# define OTG_HMC(w) (((w)>>0)&0x3f)
-#define OTG_CTRL (OTG_BASE + 0x0c)
-# define OTG_USB2_EN (1 << 29)
-# define OTG_USB2_DP (1 << 28)
-# define OTG_USB2_DM (1 << 27)
-# define OTG_USB1_EN (1 << 26)
-# define OTG_USB1_DP (1 << 25)
-# define OTG_USB1_DM (1 << 24)
-# define OTG_USB0_EN (1 << 23)
-# define OTG_USB0_DP (1 << 22)
-# define OTG_USB0_DM (1 << 21)
-# define OTG_ASESSVLD (1 << 20)
-# define OTG_BSESSEND (1 << 19)
-# define OTG_BSESSVLD (1 << 18)
-# define OTG_VBUSVLD (1 << 17)
-# define OTG_ID (1 << 16)
-# define OTG_DRIVER_SEL (1 << 15)
-# define OTG_A_SETB_HNPEN (1 << 12)
-# define OTG_A_BUSREQ (1 << 11)
-# define OTG_B_HNPEN (1 << 9)
-# define OTG_B_BUSREQ (1 << 8)
-# define OTG_BUSDROP (1 << 7)
-# define OTG_PULLDOWN (1 << 5)
-# define OTG_PULLUP (1 << 4)
-# define OTG_DRV_VBUS (1 << 3)
-# define OTG_PD_VBUS (1 << 2)
-# define OTG_PU_VBUS (1 << 1)
-# define OTG_PU_ID (1 << 0)
-#define OTG_IRQ_EN (OTG_BASE + 0x10) /* 16-bit */
-# define DRIVER_SWITCH (1 << 15)
-# define A_VBUS_ERR (1 << 13)
-# define A_REQ_TMROUT (1 << 12)
-# define A_SRP_DETECT (1 << 11)
-# define B_HNP_FAIL (1 << 10)
-# define B_SRP_TMROUT (1 << 9)
-# define B_SRP_DONE (1 << 8)
-# define B_SRP_STARTED (1 << 7)
-# define OPRT_CHG (1 << 0)
-#define OTG_IRQ_SRC (OTG_BASE + 0x14) /* 16-bit */
- // same bits as in IRQ_EN
-#define OTG_OUTCTRL (OTG_BASE + 0x18) /* 16-bit */
-# define OTGVPD (1 << 14)
-# define OTGVPU (1 << 13)
-# define OTGPUID (1 << 12)
-# define USB2VDR (1 << 10)
-# define USB2PDEN (1 << 9)
-# define USB2PUEN (1 << 8)
-# define USB1VDR (1 << 6)
-# define USB1PDEN (1 << 5)
-# define USB1PUEN (1 << 4)
-# define USB0VDR (1 << 2)
-# define USB0PDEN (1 << 1)
-# define USB0PUEN (1 << 0)
-#define OTG_TEST (OTG_BASE + 0x20) /* 16-bit */
-#define OTG_VENDOR_CODE (OTG_BASE + 0xfc) /* 16-bit */
-
-/*-------------------------------------------------------------------------*/
-
-/* OMAP1 */
-#define USB_TRANSCEIVER_CTRL (0xfffe1000 + 0x0064)
-# define CONF_USB2_UNI_R (1 << 8)
-# define CONF_USB1_UNI_R (1 << 7)
-# define CONF_USB_PORT0_R(x) (((x)>>4)&0x7)
-# define CONF_USB0_ISOLATE_R (1 << 3)
-# define CONF_USB_PWRDN_DM_R (1 << 2)
-# define CONF_USB_PWRDN_DP_R (1 << 1)
-
-/* OMAP2 */
-# define USB_UNIDIR 0x0
-# define USB_UNIDIR_TLL 0x1
-# define USB_BIDIR 0x2
-# define USB_BIDIR_TLL 0x3
-# define USBTXWRMODEI(port, x) ((x) << (22 - (port * 2)))
-# define USBT2TLL5PI (1 << 17)
-# define USB0PUENACTLOI (1 << 16)
-# define USBSTANDBYCTRL (1 << 15)
/* AM35x */
/* USB 2.0 PHY Control */
#define CONF2_PHY_GPIOMODE (1 << 23)
+++ /dev/null
- /*
- * arch/arm/plat-omap/usb.c -- platform level USB initialization
- *
- * Copyright (C) 2004 Texas Instruments, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-
-#undef DEBUG
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/io.h>
-
-#include <plat/usb.h>
-#include <plat/board.h>
-
-#include <mach/hardware.h>
-
-#ifdef CONFIG_ARCH_OMAP_OTG
-
-void __init
-omap_otg_init(struct omap_usb_config *config)
-{
- u32 syscon;
- int alt_pingroup = 0;
-
- /* NOTE: no bus or clock setup (yet?) */
-
- syscon = omap_readl(OTG_SYSCON_1) & 0xffff;
- if (!(syscon & OTG_RESET_DONE))
- pr_debug("USB resets not complete?\n");
-
- //omap_writew(0, OTG_IRQ_EN);
-
- /* pin muxing and transceiver pinouts */
- if (config->pins[0] > 2) /* alt pingroup 2 */
- alt_pingroup = 1;
- syscon |= config->usb0_init(config->pins[0], is_usb0_device(config));
- syscon |= config->usb1_init(config->pins[1]);
- syscon |= config->usb2_init(config->pins[2], alt_pingroup);
- pr_debug("OTG_SYSCON_1 = %08x\n", omap_readl(OTG_SYSCON_1));
- omap_writel(syscon, OTG_SYSCON_1);
-
- syscon = config->hmc_mode;
- syscon |= USBX_SYNCHRO | (4 << 16) /* B_ASE0_BRST */;
-#ifdef CONFIG_USB_OTG
- if (config->otg)
- syscon |= OTG_EN;
-#endif
- if (cpu_class_is_omap1())
- pr_debug("USB_TRANSCEIVER_CTRL = %03x\n",
- omap_readl(USB_TRANSCEIVER_CTRL));
- pr_debug("OTG_SYSCON_2 = %08x\n", omap_readl(OTG_SYSCON_2));
- omap_writel(syscon, OTG_SYSCON_2);
-
- printk("USB: hmc %d", config->hmc_mode);
- if (!alt_pingroup)
- printk(", usb2 alt %d wires", config->pins[2]);
- else if (config->pins[0])
- printk(", usb0 %d wires%s", config->pins[0],
- is_usb0_device(config) ? " (dev)" : "");
- if (config->pins[1])
- printk(", usb1 %d wires", config->pins[1]);
- if (!alt_pingroup && config->pins[2])
- printk(", usb2 %d wires", config->pins[2]);
- if (config->otg)
- printk(", Mini-AB on usb%d", config->otg - 1);
- printk("\n");
-
- if (cpu_class_is_omap1()) {
- u16 w;
-
- /* leave USB clocks/controllers off until needed */
- w = omap_readw(ULPD_SOFT_REQ);
- w &= ~SOFT_USB_CLK_REQ;
- omap_writew(w, ULPD_SOFT_REQ);
-
- w = omap_readw(ULPD_CLOCK_CTRL);
- w &= ~USB_MCLK_EN;
- w |= DIS_USB_PVCI_CLK;
- omap_writew(w, ULPD_CLOCK_CTRL);
- }
- syscon = omap_readl(OTG_SYSCON_1);
- syscon |= HST_IDLE_EN|DEV_IDLE_EN|OTG_IDLE_EN;
-
-#ifdef CONFIG_USB_GADGET_OMAP
- if (config->otg || config->register_dev) {
- struct platform_device *udc_device = config->udc_device;
- int status;
-
- syscon &= ~DEV_IDLE_EN;
- udc_device->dev.platform_data = config;
- status = platform_device_register(udc_device);
- if (status)
- pr_debug("can't register UDC device, %d\n", status);
- }
-#endif
-
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
- if (config->otg || config->register_host) {
- struct platform_device *ohci_device = config->ohci_device;
- int status;
-
- syscon &= ~HST_IDLE_EN;
- ohci_device->dev.platform_data = config;
- status = platform_device_register(ohci_device);
- if (status)
- pr_debug("can't register OHCI device, %d\n", status);
- }
-#endif
-
-#ifdef CONFIG_USB_OTG
- if (config->otg) {
- struct platform_device *otg_device = config->otg_device;
- int status;
-
- syscon &= ~OTG_IDLE_EN;
- otg_device->dev.platform_data = config;
- status = platform_device_register(otg_device);
- if (status)
- pr_debug("can't register OTG device, %d\n", status);
- }
-#endif
- pr_debug("OTG_SYSCON_1 = %08x\n", omap_readl(OTG_SYSCON_1));
- omap_writel(syscon, OTG_SYSCON_1);
-}
-
-#else
-void omap_otg_init(struct omap_usb_config *config) {}
-#endif
#include <linux/interrupt.h>
#include <linux/ioctl.h>
#include <linux/completion.h>
+#include <linux/io.h>
#include <asm/uaccess.h>
config USB_OMAP
tristate "OMAP USB Device Controller"
- depends on ARCH_OMAP
+ depends on ARCH_OMAP1
select ISP1301_OMAP if MACH_OMAP_H2 || MACH_OMAP_H3 || MACH_OMAP_H4_OTG
select USB_OTG_UTILS if ARCH_OMAP
help
#include <asm/mach-types.h>
#include <plat/dma.h>
-#include <plat/usb.h>
+
+#include <mach/usb.h>
#include "omap_udc.h"
config USB_OHCI_HCD_OMAP1
bool "OHCI support for OMAP1/2 chips"
- depends on USB_OHCI_HCD && (ARCH_OMAP1 || ARCH_OMAP2)
+ depends on USB_OHCI_HCD && ARCH_OMAP1
default y
---help---
Enables support for the OHCI controller on OMAP1/2 chips.
#include <linux/clk.h>
#include <linux/gpio.h>
-#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/mach-types.h>
#include <plat/mux.h>
-#include <mach/irqs.h>
#include <plat/fpga.h>
-#include <plat/usb.h>
+
+#include <mach/hardware.h>
+#include <mach/irqs.h>
+#include <mach/usb.h>
/* OMAP-1510 OHCI has its own MMU for DMA */
#include <asm/irq.h>
#include <asm/mach-types.h>
-#include <plat/usb.h>
#include <plat/mux.h>
+#include <mach/usb.h>
#ifndef DEBUG
#undef VERBOSE
projects / karo-tx-linux.git / commitdiff