#include <mach/irqs.h>
#include <mach/am35xx.h>
#include <plat/usb.h>
+#include "control.h"
#if defined(CONFIG_USB_MUSB_OMAP2PLUS) || defined (CONFIG_USB_MUSB_AM35X)
+static void am35x_musb_reset(void)
+{
+ u32 regval;
+
+ /* Reset the musb interface */
+ regval = omap_ctrl_readl(AM35XX_CONTROL_IP_SW_RESET);
+
+ regval |= AM35XX_USBOTGSS_SW_RST;
+ omap_ctrl_writel(regval, AM35XX_CONTROL_IP_SW_RESET);
+
+ regval &= ~AM35XX_USBOTGSS_SW_RST;
+ omap_ctrl_writel(regval, AM35XX_CONTROL_IP_SW_RESET);
+
+ regval = omap_ctrl_readl(AM35XX_CONTROL_IP_SW_RESET);
+}
+
+static void am35x_musb_phy_power(u8 on)
+{
+ unsigned long timeout = jiffies + msecs_to_jiffies(100);
+ u32 devconf2;
+
+ if (on) {
+ /*
+ * Start the on-chip PHY and its PLL.
+ */
+ devconf2 = omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2);
+
+ devconf2 &= ~(CONF2_RESET | CONF2_PHYPWRDN | CONF2_OTGPWRDN);
+ devconf2 |= CONF2_PHY_PLLON;
+
+ omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2);
+
+ pr_info(KERN_INFO "Waiting for PHY clock good...\n");
+ while (!(omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2)
+ & CONF2_PHYCLKGD)) {
+ cpu_relax();
+
+ if (time_after(jiffies, timeout)) {
+ pr_err(KERN_ERR "musb PHY clock good timed out\n");
+ break;
+ }
+ }
+ } else {
+ /*
+ * Power down the on-chip PHY.
+ */
+ devconf2 = omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2);
+
+ devconf2 &= ~CONF2_PHY_PLLON;
+ devconf2 |= CONF2_PHYPWRDN | CONF2_OTGPWRDN;
+ omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2);
+ }
+}
+
+static void am35x_musb_clear_irq(void)
+{
+ u32 regval;
+
+ regval = omap_ctrl_readl(AM35XX_CONTROL_LVL_INTR_CLEAR);
+ regval |= AM35XX_USBOTGSS_INT_CLR;
+ omap_ctrl_writel(regval, AM35XX_CONTROL_LVL_INTR_CLEAR);
+ regval = omap_ctrl_readl(AM35XX_CONTROL_LVL_INTR_CLEAR);
+}
+
+static void am35x_musb_set_mode(u8 musb_mode)
+{
+ u32 devconf2 = omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2);
+
+ devconf2 &= ~CONF2_OTGMODE;
+ switch (musb_mode) {
+#ifdef CONFIG_USB_MUSB_HDRC_HCD
+ case MUSB_HOST: /* Force VBUS valid, ID = 0 */
+ devconf2 |= CONF2_FORCE_HOST;
+ break;
+#endif
+#ifdef CONFIG_USB_GADGET_MUSB_HDRC
+ case MUSB_PERIPHERAL: /* Force VBUS valid, ID = 1 */
+ devconf2 |= CONF2_FORCE_DEVICE;
+ break;
+#endif
+#ifdef CONFIG_USB_MUSB_OTG
+ case MUSB_OTG: /* Don't override the VBUS/ID comparators */
+ devconf2 |= CONF2_NO_OVERRIDE;
+ break;
+#endif
+ default:
+ pr_info(KERN_INFO "Unsupported mode %u\n", musb_mode);
+ }
+
+ omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2);
+}
+
static struct resource musb_resources[] = {
[0] = { /* start and end set dynamically */
.flags = IORESOURCE_MEM,
musb_device.name = "musb-am35x";
musb_resources[0].start = AM35XX_IPSS_USBOTGSS_BASE;
musb_resources[1].start = INT_35XX_USBOTG_IRQ;
+ board_data->set_phy_power = am35x_musb_phy_power;
+ board_data->clear_irq = am35x_musb_clear_irq;
+ board_data->set_mode = am35x_musb_set_mode;
+ board_data->reset = am35x_musb_reset;
} else if (cpu_is_omap34xx()) {
musb_resources[0].start = OMAP34XX_HSUSB_OTG_BASE;
} else if (cpu_is_omap44xx()) {
#include <linux/platform_device.h>
#include <linux/dma-mapping.h>
-#include <plat/control.h>
#include <plat/usb.h>
#include "musb_core.h"
};
#define glue_to_musb(g) platform_get_drvdata(g->musb)
-static inline void phy_on(void)
-{
- unsigned long timeout = jiffies + msecs_to_jiffies(100);
- u32 devconf2;
-
- /*
- * Start the on-chip PHY and its PLL.
- */
- devconf2 = omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2);
-
- devconf2 &= ~(CONF2_RESET | CONF2_PHYPWRDN | CONF2_OTGPWRDN);
- devconf2 |= CONF2_PHY_PLLON;
-
- omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2);
-
- DBG(1, "Waiting for PHY clock good...\n");
- while (!(omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2)
- & CONF2_PHYCLKGD)) {
- cpu_relax();
-
- if (time_after(jiffies, timeout)) {
- DBG(1, "musb PHY clock good timed out\n");
- break;
- }
- }
-}
-
-static inline void phy_off(void)
-{
- u32 devconf2;
-
- /*
- * Power down the on-chip PHY.
- */
- devconf2 = omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2);
-
- devconf2 &= ~CONF2_PHY_PLLON;
- devconf2 |= CONF2_PHYPWRDN | CONF2_OTGPWRDN;
- omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2);
-}
-
/*
* am35x_musb_enable - enable interrupts
*/
{
struct musb *musb = hci;
void __iomem *reg_base = musb->ctrl_base;
+ struct device *dev = musb->controller;
+ struct musb_hdrc_platform_data *plat = dev->platform_data;
+ struct omap_musb_board_data *data = plat->board_data;
unsigned long flags;
irqreturn_t ret = IRQ_NONE;
- u32 epintr, usbintr, lvl_intr;
+ u32 epintr, usbintr;
spin_lock_irqsave(&musb->lock, flags);
/* EOI needs to be written for the IRQ to be re-asserted. */
if (ret == IRQ_HANDLED || epintr || usbintr) {
/* clear level interrupt */
- lvl_intr = omap_ctrl_readl(AM35XX_CONTROL_LVL_INTR_CLEAR);
- lvl_intr |= AM35XX_USBOTGSS_INT_CLR;
- omap_ctrl_writel(lvl_intr, AM35XX_CONTROL_LVL_INTR_CLEAR);
+ if (data->clear_irq)
+ data->clear_irq();
/* write EOI */
musb_writel(reg_base, USB_END_OF_INTR_REG, 0);
}
static int am35x_musb_set_mode(struct musb *musb, u8 musb_mode)
{
- u32 devconf2 = omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2);
+ struct device *dev = musb->controller;
+ struct musb_hdrc_platform_data *plat = dev->platform_data;
+ struct omap_musb_board_data *data = plat->board_data;
+ int retval = 0;
- devconf2 &= ~CONF2_OTGMODE;
- switch (musb_mode) {
-#ifdef CONFIG_USB_MUSB_HDRC_HCD
- case MUSB_HOST: /* Force VBUS valid, ID = 0 */
- devconf2 |= CONF2_FORCE_HOST;
- break;
-#endif
-#ifdef CONFIG_USB_GADGET_MUSB_HDRC
- case MUSB_PERIPHERAL: /* Force VBUS valid, ID = 1 */
- devconf2 |= CONF2_FORCE_DEVICE;
- break;
-#endif
-#ifdef CONFIG_USB_MUSB_OTG
- case MUSB_OTG: /* Don't override the VBUS/ID comparators */
- devconf2 |= CONF2_NO_OVERRIDE;
- break;
-#endif
- default:
- DBG(2, "Trying to set unsupported mode %u\n", musb_mode);
- }
+ if (data->set_mode)
+ data->set_mode(musb_mode);
+ else
+ retval = -EIO;
- omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2);
- return 0;
+ return retval;
}
static int am35x_musb_init(struct musb *musb)
{
+ struct device *dev = musb->controller;
+ struct musb_hdrc_platform_data *plat = dev->platform_data;
+ struct omap_musb_board_data *data = plat->board_data;
void __iomem *reg_base = musb->ctrl_base;
- u32 rev, lvl_intr, sw_reset;
+ u32 rev;
musb->mregs += USB_MENTOR_CORE_OFFSET;
if (is_host_enabled(musb))
setup_timer(&otg_workaround, otg_timer, (unsigned long) musb);
- /* Global reset */
- sw_reset = omap_ctrl_readl(AM35XX_CONTROL_IP_SW_RESET);
-
- sw_reset |= AM35XX_USBOTGSS_SW_RST;
- omap_ctrl_writel(sw_reset, AM35XX_CONTROL_IP_SW_RESET);
-
- sw_reset &= ~AM35XX_USBOTGSS_SW_RST;
- omap_ctrl_writel(sw_reset, AM35XX_CONTROL_IP_SW_RESET);
+ /* Reset the musb */
+ if (data->reset)
+ data->reset();
/* Reset the controller */
musb_writel(reg_base, USB_CTRL_REG, AM35X_SOFT_RESET_MASK);
/* Start the on-chip PHY and its PLL. */
- phy_on();
+ if (data->set_phy_power)
+ data->set_phy_power(1);
msleep(5);
musb->isr = am35x_musb_interrupt;
/* clear level interrupt */
- lvl_intr = omap_ctrl_readl(AM35XX_CONTROL_LVL_INTR_CLEAR);
- lvl_intr |= AM35XX_USBOTGSS_INT_CLR;
- omap_ctrl_writel(lvl_intr, AM35XX_CONTROL_LVL_INTR_CLEAR);
+ if (data->clear_irq)
+ data->clear_irq();
return 0;
}
static int am35x_musb_exit(struct musb *musb)
{
+ struct device *dev = musb->controller;
+ struct musb_hdrc_platform_data *plat = dev->platform_data;
+ struct omap_musb_board_data *data = plat->board_data;
+
if (is_host_enabled(musb))
del_timer_sync(&otg_workaround);
- phy_off();
+ /* Shutdown the on-chip PHY and its PLL. */
+ if (data->set_phy_power)
+ data->set_phy_power(0);
otg_put_transceiver(musb->xceiv);
usb_nop_xceiv_unregister();
static int am35x_suspend(struct device *dev)
{
struct am35x_glue *glue = dev_get_drvdata(dev);
+ struct musb_hdrc_platform_data *plat = dev->platform_data;
+ struct omap_musb_board_data *data = plat->board_data;
+
+ /* Shutdown the on-chip PHY and its PLL. */
+ if (data->set_phy_power)
+ data->set_phy_power(0);
- phy_off();
clk_disable(glue->phy_clk);
clk_disable(glue->clk);
static int am35x_resume(struct device *dev)
{
struct am35x_glue *glue = dev_get_drvdata(dev);
+ struct musb_hdrc_platform_data *plat = dev->platform_data;
+ struct omap_musb_board_data *data = plat->board_data;
int ret;
- phy_on();
+ /* Start the on-chip PHY and its PLL. */
+ if (data->set_phy_power)
+ data->set_phy_power(1);
+
ret = clk_enable(glue->phy_clk);
if (ret) {
dev_err(dev, "failed to enable PHY clock\n");
projects / linux-beck.git / commitdiff