--- /dev/null
+* Renesas SH-Mobile Serial Communication Interface
+
+Required properties:
+- compatible : Should be "renesas,sci-<port type>-uart", where <port type> may be
+ SCI, SCIF, IRDA, SCIFA or SCIFB.
+- reg : Address and length of the register set for the device
+- interrupts : Should contain the following IRQs: ERI, RXI, TXI and BRI.
+- cell-index : The device id.
+- renesas,scscr : Should contain a bitfield used by the Serial Control Register.
+ b7 = SCSCR_TIE
+ b6 = SCSCR_RIE
+ b5 = SCSCR_TE
+ b4 = SCSCR_RE
+ b3 = SCSCR_REIE
+ b2 = SCSCR_TOIE
+ b1 = SCSCR_CKE1
+ b0 = SCSCR_CKE0
+- renesas,scbrr-algo-id : Algorithm ID for the Bit Rate Register
+ 1 = SCBRR_ALGO_1 ((clk + 16 * bps) / (16 * bps) - 1)
+ 2 = SCBRR_ALGO_2 ((clk + 16 * bps) / (32 * bps) - 1)
+ 3 = SCBRR_ALGO_3 (((clk * 2) + 16 * bps) / (16 * bps) - 1)
+ 4 = SCBRR_ALGO_4 (((clk * 2) + 16 * bps) / (32 * bps) - 1)
+ 5 = SCBRR_ALGO_5 (((clk * 1000 / 32) / bps) - 1)
+
+Optional properties:
+- renesas,autoconf : Set if device is capable of auto configuration
+- renesas,regtype : Overwrite the register layout. In most cases you can rely
+ on auto-probing (omit this property or set to 0) but some legacy devices
+ use a non-default register layout. Possible layouts are
+ 0 = SCIx_PROBE_REGTYPE (default)
+ 1 = SCIx_SCI_REGTYPE
+ 2 = SCIx_IRDA_REGTYPE
+ 3 = SCIx_SCIFA_REGTYPE
+ 4 = SCIx_SCIFB_REGTYPE
+ 5 = SCIx_SH2_SCIF_FIFODATA_REGTYPE
+ 6 = SCIx_SH3_SCIF_REGTYPE
+ 7 = SCIx_SH4_SCIF_REGTYPE
+ 8 = SCIx_SH4_SCIF_NO_SCSPTR_REGTYPE
+ 9 = SCIx_SH4_SCIF_FIFODATA_REGTYPE
+ 10 = SCIx_SH7705_SCIF_REGTYPE
+
+
+Example:
+ sci@0xe6c50000 {
+ compatible = "renesas,sci-SCIFA-uart";
+ interrupt-parent = <&intca>;
+ reg = <0xe6c50000 0x100>;
+ interrupts = <0x0c20>, <0x0c20>, <0x0c20>, <0x0c20>;
+ cell-index = <1>;
+ renesas,scscr = <0x30>;
+ renesas,scbrr-algo-id = <4>;
+ renesas,autoconf;
+ };
return 0;
}
+#ifdef CONFIG_OF
+static const struct of_device_id of_sci_match[] = {
+ { .compatible = "renesas,sci-SCI-uart",
+ .data = (void *)PORT_SCI },
+ { .compatible = "renesas,sci-SCIF-uart",
+ .data = (void *)PORT_SCIF },
+ { .compatible = "renesas,sci-IRDA-uart",
+ .data = (void *)PORT_IRDA },
+ { .compatible = "renesas,sci-SCIFA-uart",
+ .data = (void *)PORT_SCIFA },
+ { .compatible = "renesas,sci-SCIFB-uart",
+ .data = (void *)PORT_SCIFB },
+ {},
+};
+MODULE_DEVICE_TABLE(of, of_sci_match);
+
+static struct plat_sci_port *sci_parse_dt(struct platform_device *pdev,
+ int *dev_id)
+{
+ struct plat_sci_port *p;
+ struct device_node *np = pdev->dev.of_node;
+ const struct of_device_id *match;
+ struct resource *res;
+ const __be32 *prop;
+ int i, irq, val;
+
+ match = of_match_node(of_sci_match, pdev->dev.of_node);
+ if (!match || !match->data) {
+ dev_err(&pdev->dev, "OF match error\n");
+ return NULL;
+ }
+
+ p = devm_kzalloc(&pdev->dev, sizeof(struct plat_sci_port), GFP_KERNEL);
+ if (!p) {
+ dev_err(&pdev->dev, "failed to allocate DT config data\n");
+ return NULL;
+ }
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ dev_err(&pdev->dev, "failed to get I/O memory\n");
+ return NULL;
+ }
+ p->mapbase = res->start;
+
+ for (i = 0; i < SCIx_NR_IRQS; i++) {
+ irq = platform_get_irq(pdev, i);
+ if (irq < 0) {
+ dev_err(&pdev->dev, "failed to get irq data %d\n", i);
+ return NULL;
+ }
+ p->irqs[i] = irq;
+ }
+
+ prop = of_get_property(np, "cell-index", NULL);
+ if (!prop) {
+ dev_err(&pdev->dev, "required DT prop cell-index missing\n");
+ return NULL;
+ }
+ *dev_id = be32_to_cpup(prop);
+
+ prop = of_get_property(np, "renesas,scscr", NULL);
+ if (!prop) {
+ dev_err(&pdev->dev, "required DT prop scscr missing\n");
+ return NULL;
+ }
+ p->scscr = be32_to_cpup(prop);
+
+ prop = of_get_property(np, "renesas,scbrr-algo-id", NULL);
+ if (!prop) {
+ dev_err(&pdev->dev, "required DT prop scbrr-algo-id missing\n");
+ return NULL;
+ }
+ val = be32_to_cpup(prop);
+ if (val <= SCBRR_ALGO_INVALID || val >= SCBRR_NR_ALGOS) {
+ dev_err(&pdev->dev, "DT prop scbrr-algo-id out of range\n");
+ return NULL;
+ }
+ p->scbrr_algo_id = val;
+
+ p->flags = UPF_IOREMAP;
+ if (of_get_property(np, "renesas,autoconf", NULL))
+ p->flags |= UPF_BOOT_AUTOCONF;
+
+ prop = of_get_property(np, "renesas,regtype", NULL);
+ if (prop) {
+ val = be32_to_cpup(prop);
+ if (val < SCIx_PROBE_REGTYPE || val >= SCIx_NR_REGTYPES) {
+ dev_err(&pdev->dev, "DT prop regtype out of range\n");
+ return NULL;
+ }
+ p->regtype = val;
+ }
+
+ p->type = (unsigned int)match->data;
+
+ return p;
+}
+#else
+static struct plat_sci_port *sci_parse_dt(struct platform_device *pdev,
+ int *dev_id)
+{
+ return NULL;
+}
+#endif /* CONFIG_OF */
+
static int sci_probe_single(struct platform_device *dev,
unsigned int index,
struct plat_sci_port *p,
static int sci_probe(struct platform_device *dev)
{
- struct plat_sci_port *p = dev->dev.platform_data;
- struct sci_port *sp = &sci_ports[dev->id];
- int ret;
+ struct plat_sci_port *p;
+ struct sci_port *sp;
+ int ret, dev_id = dev->id;
/*
* If we've come here via earlyprintk initialization, head off to
if (is_early_platform_device(dev))
return sci_probe_earlyprintk(dev);
+ if (dev->dev.of_node)
+ p = sci_parse_dt(dev, &dev_id);
+ else
+ p = dev->dev.platform_data;
+
+ if (!p) {
+ dev_err(&dev->dev, "no setup data supplied\n");
+ return -EINVAL;
+ }
+
+ sp = &sci_ports[dev_id];
platform_set_drvdata(dev, sp);
- ret = sci_probe_single(dev, dev->id, p, sp);
+ ret = sci_probe_single(dev, dev_id, p, sp);
if (ret)
return ret;
.name = "sh-sci",
.owner = THIS_MODULE,
.pm = &sci_dev_pm_ops,
+ .of_match_table = of_match_ptr(of_sci_match),
},
};