ARM: SMP: get rid of references to poke_milo and Milo

Milo is an old boot loader, which is no longer relevant for these
platforms.  References to it are misleading.  Move the code out
of poke_milo(), and remove references to milo in comments.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

diff --git a/arch/arm/mach-realview/platsmp.c b/arch/arm/mach-realview/platsmp.c
index 6595e875fb2f9bd4cac99b41f97eb31fa3607c0e..ef3cc86f5140833f73d8aef674171aa725a2a613 100644 (file)
--- a/arch/arm/mach-realview/platsmp.c
+++ b/arch/arm/mach-realview/platsmp.c
@@ -99,14 +99,9 @@ int __cpuinit boot_secondary(unsigned int cpu, struct task_struct *idle)
        flush_cache_all();
 
        /*
-        * XXX
-        *
-        * This is a later addition to the booting protocol: the
-        * bootMonitor now puts secondary cores into WFI, so
-        * poke_milo() no longer gets the cores moving; we need
-        * to send a soft interrupt to wake the secondary core.
-        * Use smp_cross_call() for this, since there's little
-        * point duplicating the code here
+        * Send the secondary CPU a soft interrupt, thereby causing
+        * the boot monitor to read the system wide flags register,
+        * and branch to the address found there.
         */
        smp_cross_call(cpumask_of(cpu), 1);
 
@@ -128,22 +123,6 @@ int __cpuinit boot_secondary(unsigned int cpu, struct task_struct *idle)
        return pen_release != -1 ? -ENOSYS : 0;
 }
 
-static void __init poke_milo(void)
-{
-       /* nobody is to be released from the pen yet */
-       pen_release = -1;
-
-       /*
-        * Write the address of secondary startup into the system-wide flags
-        * register. The BootMonitor waits for this register to become
-        * non-zero.
-        */
-       __raw_writel(BSYM(virt_to_phys(realview_secondary_startup)),
-                    __io_address(REALVIEW_SYS_FLAGSSET));
-
-       mb();
-}
-
 /*
  * Initialise the CPU possible map early - this describes the CPUs
  * which may be present or become present in the system.
@@ -189,13 +168,6 @@ void __init smp_prepare_cpus(unsigned int max_cpus)
        for (i = 0; i < max_cpus; i++)
                set_cpu_present(i, true);
 
-       /*
-        * Initialise the SCU if there are more than one CPU and let
-        * them know where to start. Note that, on modern versions of
-        * MILO, the "poke" doesn't actually do anything until each
-        * individual core is sent a soft interrupt to get it out of
-        * WFI
-        */
        if (max_cpus > 1) {
                /*
                 * Enable the local timer or broadcast device for the
@@ -204,6 +176,14 @@ void __init smp_prepare_cpus(unsigned int max_cpus)
                percpu_timer_setup();
 
                scu_enable(scu_base_addr());
-               poke_milo();
+
+               /*
+                * Write the address of secondary startup into the
+                * system-wide flags register. The BootMonitor waits
+                * until it receives a soft interrupt, and then the
+                * secondary CPU branches to this address.
+                */
+               __raw_writel(BSYM(virt_to_phys(realview_secondary_startup)),
+                            __io_address(REALVIEW_SYS_FLAGSSET));
        }
 }

diff --git a/arch/arm/mach-tegra/platsmp.c b/arch/arm/mach-tegra/platsmp.c
index 5b194dd815a8a7b3aed9a7d38c15d3a5589bef5b..66d0634e7a962396b31fc0f0d8c83031b703eae2 100644 (file)
--- a/arch/arm/mach-tegra/platsmp.c
+++ b/arch/arm/mach-tegra/platsmp.c
@@ -148,13 +148,6 @@ void __init smp_prepare_cpus(unsigned int max_cpus)
        for (i = 0; i < max_cpus; i++)
                set_cpu_present(i, true);
 
-       /*
-        * Initialise the SCU if there are more than one CPU and let
-        * them know where to start. Note that, on modern versions of
-        * MILO, the "poke" doesn't actually do anything until each
-        * individual core is sent a soft interrupt to get it out of
-        * WFI
-        */
        if (max_cpus > 1) {
                percpu_timer_setup();
                scu_enable(scu_base);