WM8994_CP_DYN_PWR |
WM8994_CP_DYN_SRC_SEL_MASK,
source | WM8994_CP_DYN_PWR);
- wm8994->hubs.class_w = true;
} else {
dev_dbg(codec->dev, "Class W disabled\n");
snd_soc_update_bits(codec, WM8994_CLASS_W_1,
WM8994_CP_DYN_PWR, 0);
- wm8994->hubs.class_w = false;
}
}
wm8994->hubs.dcs_readback_mode = 2;
wm8994->hubs.no_series_update = 1;
wm8994->hubs.hp_startup_mode = 1;
- wm8994->hubs.no_cache_class_w = true;
+ wm8994->hubs.no_cache_dac_hp_direct = true;
wm8994->fll_byp = true;
switch (wm8994->revision) {
}
EXPORT_SYMBOL_GPL(wm_hubs_dcs_done);
+static bool wm_hubs_dac_hp_direct(struct snd_soc_codec *codec)
+{
+ int reg;
+
+ /* If we're going via the mixer we'll need to do additional checks */
+ reg = snd_soc_read(codec, WM8993_OUTPUT_MIXER1);
+ if (!(reg & WM8993_DACL_TO_HPOUT1L)) {
+ if (reg & ~WM8993_DACL_TO_MIXOUTL) {
+ dev_vdbg(codec->dev, "Analogue paths connected: %x\n",
+ reg & ~WM8993_DACL_TO_HPOUT1L);
+ return false;
+ } else {
+ dev_vdbg(codec->dev, "HPL connected to mixer\n");
+ return false;
+ }
+ } else {
+ dev_vdbg(codec->dev, "HPL connected to DAC\n");
+ }
+
+ reg = snd_soc_read(codec, WM8993_OUTPUT_MIXER2);
+ if (!(reg & WM8993_DACR_TO_HPOUT1R)) {
+ if (reg & ~WM8993_DACR_TO_MIXOUTR) {
+ dev_vdbg(codec->dev, "Analogue paths connected: %x\n",
+ reg & ~WM8993_DACR_TO_HPOUT1R);
+ return false;
+ } else {
+ dev_vdbg(codec->dev, "HPR connected to mixer\n");
+ return false;
+ }
+ } else {
+ dev_vdbg(codec->dev, "HPR connected to DAC\n");
+ }
+
+ return true;
+}
+
/*
* Startup calibration of the DC servo
*/
/* If we're using a digital only path and have a previously
* callibrated DC servo offset stored then use that. */
- if (hubs->class_w && hubs->class_w_dcs) {
+ if (wm_hubs_dac_hp_direct(codec) && hubs->dac_hp_direct_dcs) {
dev_dbg(codec->dev, "Using cached DC servo offset %x\n",
- hubs->class_w_dcs);
- snd_soc_write(codec, dcs_reg, hubs->class_w_dcs);
+ hubs->dac_hp_direct_dcs);
+ snd_soc_write(codec, dcs_reg, hubs->dac_hp_direct_dcs);
wait_for_dc_servo(codec,
WM8993_DCS_TRIG_DAC_WR_0 |
WM8993_DCS_TRIG_DAC_WR_1);
/* Save the callibrated offset if we're in class W mode and
* therefore don't have any analogue signal mixed in. */
- if (hubs->class_w && !hubs->no_cache_class_w)
- hubs->class_w_dcs = dcs_cfg;
+ if (wm_hubs_dac_hp_direct(codec) && !hubs->no_cache_dac_hp_direct)
+ hubs->dac_hp_direct_dcs = dcs_cfg;
}
/*
ret = snd_soc_put_volsw(kcontrol, ucontrol);
/* Updating the analogue gains invalidates the DC servo cache */
- hubs->class_w_dcs = 0;
+ hubs->dac_hp_direct_dcs = 0;
/* If we're applying an offset correction then updating the
* callibration would be likely to introduce further offsets. */