/* Flow Control */
s32 (*fc_enable)(struct ixgbe_hw *);
+ s32 (*setup_fc)(struct ixgbe_hw *);
/* Manageability interface */
s32 (*set_fw_drv_ver)(struct ixgbe_hw *, u8, u8, u8, u8);
#define IXGBE_KRM_PORT_CAR_GEN_CTRL(P) ((P) ? 0x8010 : 0x4010)
#define IXGBE_KRM_LINK_CTRL_1(P) ((P) ? 0x820C : 0x420C)
+#define IXGBE_KRM_AN_CNTL_1(P) ((P) ? 0x822C : 0x422C)
#define IXGBE_KRM_DSP_TXFFE_STATE_4(P) ((P) ? 0x8634 : 0x4634)
#define IXGBE_KRM_DSP_TXFFE_STATE_5(P) ((P) ? 0x8638 : 0x4638)
#define IXGBE_KRM_RX_TRN_LINKUP_CTRL(P) ((P) ? 0x8B00 : 0x4B00)
#define IXGBE_KRM_LINK_CTRL_1_TETH_AN_ENABLE (1 << 29)
#define IXGBE_KRM_LINK_CTRL_1_TETH_AN_RESTART (1 << 31)
+#define IXGBE_KRM_AN_CNTL_1_SYM_PAUSE (1 << 28)
+#define IXGBE_KRM_AN_CNTL_1_ASM_PAUSE (1 << 29)
+
#define IXGBE_KRM_DSP_TXFFE_STATE_C0_EN (1 << 6)
#define IXGBE_KRM_DSP_TXFFE_STATE_CP1_CN1_EN (1 << 15)
#define IXGBE_KRM_DSP_TXFFE_STATE_CO_ADAPT_EN (1 << 16)
#include "ixgbe_phy.h"
static s32 ixgbe_setup_kr_speed_x550em(struct ixgbe_hw *, ixgbe_link_speed);
+static s32 ixgbe_setup_fc_x550em(struct ixgbe_hw *);
static s32 ixgbe_get_invariants_X550_x(struct ixgbe_hw *hw)
{
mac->ops.enable_tx_laser = NULL;
mac->ops.flap_tx_laser = NULL;
mac->ops.setup_link = ixgbe_setup_mac_link_multispeed_fiber;
+ mac->ops.setup_fc = ixgbe_setup_fc_x550em;
mac->ops.setup_mac_link = ixgbe_setup_mac_link_sfp_x550em;
mac->ops.set_rate_select_speed =
ixgbe_set_soft_rate_select_speed;
break;
case ixgbe_media_type_copper:
mac->ops.setup_link = ixgbe_setup_mac_link_t_X550em;
+ mac->ops.setup_fc = ixgbe_setup_fc_generic;
mac->ops.check_link = ixgbe_check_link_t_X550em;
break;
default:
+ mac->ops.setup_fc = ixgbe_setup_fc_x550em;
break;
}
}
return status;
}
+/**
+ * ixgbe_setup_fc_x550em - Set up flow control
+ * @hw: pointer to hardware structure
+ */
+static s32 ixgbe_setup_fc_x550em(struct ixgbe_hw *hw)
+{
+ bool pause, asm_dir;
+ u32 reg_val;
+ s32 rc;
+
+ /* Validate the requested mode */
+ if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) {
+ hw_err(hw, "ixgbe_fc_rx_pause not valid in strict IEEE mode\n");
+ return IXGBE_ERR_INVALID_LINK_SETTINGS;
+ }
+
+ /* 10gig parts do not have a word in the EEPROM to determine the
+ * default flow control setting, so we explicitly set it to full.
+ */
+ if (hw->fc.requested_mode == ixgbe_fc_default)
+ hw->fc.requested_mode = ixgbe_fc_full;
+
+ /* Determine PAUSE and ASM_DIR bits. */
+ switch (hw->fc.requested_mode) {
+ case ixgbe_fc_none:
+ pause = false;
+ asm_dir = false;
+ break;
+ case ixgbe_fc_tx_pause:
+ pause = false;
+ asm_dir = true;
+ break;
+ case ixgbe_fc_rx_pause:
+ /* Rx Flow control is enabled and Tx Flow control is
+ * disabled by software override. Since there really
+ * isn't a way to advertise that we are capable of RX
+ * Pause ONLY, we will advertise that we support both
+ * symmetric and asymmetric Rx PAUSE, as such we fall
+ * through to the fc_full statement. Later, we will
+ * disable the adapter's ability to send PAUSE frames.
+ */
+ /* Fallthrough */
+ case ixgbe_fc_full:
+ pause = true;
+ asm_dir = true;
+ break;
+ default:
+ hw_err(hw, "Flow control param set incorrectly\n");
+ return IXGBE_ERR_CONFIG;
+ }
+
+ if (hw->device_id != IXGBE_DEV_ID_X550EM_X_KR)
+ return 0;
+
+ rc = ixgbe_read_iosf_sb_reg_x550(hw,
+ IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
+ if (rc)
+ return rc;
+
+ reg_val &= ~(IXGBE_KRM_AN_CNTL_1_SYM_PAUSE |
+ IXGBE_KRM_AN_CNTL_1_ASM_PAUSE);
+ if (pause)
+ reg_val |= IXGBE_KRM_AN_CNTL_1_SYM_PAUSE;
+ if (asm_dir)
+ reg_val |= IXGBE_KRM_AN_CNTL_1_ASM_PAUSE;
+ rc = ixgbe_write_iosf_sb_reg_x550(hw,
+ IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
+
+ /* This device does not fully support AN. */
+ hw->fc.disable_fc_autoneg = true;
+
+ return rc;
+}
+
/** ixgbe_enter_lplu_x550em - Transition to low power states
* @hw: pointer to hardware structure
*
.enable_rx_buff = &ixgbe_enable_rx_buff_generic, \
.get_thermal_sensor_data = NULL, \
.init_thermal_sensor_thresh = NULL, \
- .prot_autoc_read = &prot_autoc_read_generic, \
- .prot_autoc_write = &prot_autoc_write_generic, \
.enable_rx = &ixgbe_enable_rx_generic, \
.disable_rx = &ixgbe_disable_rx_x550, \
.setup_sfp = NULL,
.acquire_swfw_sync = &ixgbe_acquire_swfw_sync_X540,
.release_swfw_sync = &ixgbe_release_swfw_sync_X540,
+ .prot_autoc_read = prot_autoc_read_generic,
+ .prot_autoc_write = prot_autoc_write_generic,
+ .setup_fc = ixgbe_setup_fc_generic,
};
static const struct ixgbe_mac_operations mac_ops_X550EM_x = {
.setup_sfp = ixgbe_setup_sfp_modules_X550em,
.acquire_swfw_sync = &ixgbe_acquire_swfw_sync_X550em,
.release_swfw_sync = &ixgbe_release_swfw_sync_X550em,
+ .setup_fc = NULL, /* defined later */
};
#define X550_COMMON_EEP \
projects / karo-tx-linux.git / commitdiff