adis16240-y := adis16240_core.o
obj-$(CONFIG_ADIS16240) += adis16240.o
-sca3000-y := sca3000_core.o sca3000_ring.o
obj-$(CONFIG_SCA3000) += sca3000.o
#include <linux/spi/spi.h>
#include <linux/sysfs.h>
#include <linux/module.h>
+#include <linux/uaccess.h>
#include <linux/iio/iio.h>
#include <linux/iio/sysfs.h>
#include <linux/iio/events.h>
#include <linux/iio/buffer.h>
+#include "../ring_hw.h"
-#include "sca3000.h"
+#define SCA3000_WRITE_REG(a) (((a) << 2) | 0x02)
+#define SCA3000_READ_REG(a) ((a) << 2)
+
+#define SCA3000_REG_ADDR_REVID 0x00
+#define SCA3000_REVID_MAJOR_MASK 0xf0
+#define SCA3000_REVID_MINOR_MASK 0x0f
+
+#define SCA3000_REG_ADDR_STATUS 0x02
+#define SCA3000_LOCKED 0x20
+#define SCA3000_EEPROM_CS_ERROR 0x02
+#define SCA3000_SPI_FRAME_ERROR 0x01
+
+/* All reads done using register decrement so no need to directly access LSBs */
+#define SCA3000_REG_ADDR_X_MSB 0x05
+#define SCA3000_REG_ADDR_Y_MSB 0x07
+#define SCA3000_REG_ADDR_Z_MSB 0x09
+
+#define SCA3000_REG_ADDR_RING_OUT 0x0f
+
+/* Temp read untested - the e05 doesn't have the sensor */
+#define SCA3000_REG_ADDR_TEMP_MSB 0x13
+
+#define SCA3000_REG_ADDR_MODE 0x14
+#define SCA3000_MODE_PROT_MASK 0x28
+
+#define SCA3000_RING_BUF_ENABLE 0x80
+#define SCA3000_RING_BUF_8BIT 0x40
+/*
+ * Free fall detection triggers an interrupt if the acceleration
+ * is below a threshold for equivalent of 25cm drop
+ */
+#define SCA3000_FREE_FALL_DETECT 0x10
+#define SCA3000_MEAS_MODE_NORMAL 0x00
+#define SCA3000_MEAS_MODE_OP_1 0x01
+#define SCA3000_MEAS_MODE_OP_2 0x02
+
+/*
+ * In motion detection mode the accelerations are band pass filtered
+ * (approx 1 - 25Hz) and then a programmable threshold used to trigger
+ * and interrupt.
+ */
+#define SCA3000_MEAS_MODE_MOT_DET 0x03
+
+#define SCA3000_REG_ADDR_BUF_COUNT 0x15
+
+#define SCA3000_REG_ADDR_INT_STATUS 0x16
+
+#define SCA3000_INT_STATUS_THREE_QUARTERS 0x80
+#define SCA3000_INT_STATUS_HALF 0x40
+
+#define SCA3000_INT_STATUS_FREE_FALL 0x08
+#define SCA3000_INT_STATUS_Y_TRIGGER 0x04
+#define SCA3000_INT_STATUS_X_TRIGGER 0x02
+#define SCA3000_INT_STATUS_Z_TRIGGER 0x01
+
+/* Used to allow access to multiplexed registers */
+#define SCA3000_REG_ADDR_CTRL_SEL 0x18
+/* Only available for SCA3000-D03 and SCA3000-D01 */
+#define SCA3000_REG_CTRL_SEL_I2C_DISABLE 0x01
+#define SCA3000_REG_CTRL_SEL_MD_CTRL 0x02
+#define SCA3000_REG_CTRL_SEL_MD_Y_TH 0x03
+#define SCA3000_REG_CTRL_SEL_MD_X_TH 0x04
+#define SCA3000_REG_CTRL_SEL_MD_Z_TH 0x05
+/*
+ * BE VERY CAREFUL WITH THIS, IF 3 BITS ARE NOT SET the device
+ * will not function
+ */
+#define SCA3000_REG_CTRL_SEL_OUT_CTRL 0x0B
+#define SCA3000_OUT_CTRL_PROT_MASK 0xE0
+#define SCA3000_OUT_CTRL_BUF_X_EN 0x10
+#define SCA3000_OUT_CTRL_BUF_Y_EN 0x08
+#define SCA3000_OUT_CTRL_BUF_Z_EN 0x04
+#define SCA3000_OUT_CTRL_BUF_DIV_MASK 0x03
+#define SCA3000_OUT_CTRL_BUF_DIV_4 0x02
+#define SCA3000_OUT_CTRL_BUF_DIV_2 0x01
+
+/*
+ * Control which motion detector interrupts are on.
+ * For now only OR combinations are supported.
+ */
+#define SCA3000_MD_CTRL_PROT_MASK 0xC0
+#define SCA3000_MD_CTRL_OR_Y 0x01
+#define SCA3000_MD_CTRL_OR_X 0x02
+#define SCA3000_MD_CTRL_OR_Z 0x04
+/* Currently unsupported */
+#define SCA3000_MD_CTRL_AND_Y 0x08
+#define SCA3000_MD_CTRL_AND_X 0x10
+#define SAC3000_MD_CTRL_AND_Z 0x20
+
+/*
+ * Some control registers of complex access methods requiring this register to
+ * be used to remove a lock.
+ */
+#define SCA3000_REG_ADDR_UNLOCK 0x1e
+
+#define SCA3000_REG_ADDR_INT_MASK 0x21
+#define SCA3000_INT_MASK_PROT_MASK 0x1C
+
+#define SCA3000_INT_MASK_RING_THREE_QUARTER 0x80
+#define SCA3000_INT_MASK_RING_HALF 0x40
+
+#define SCA3000_INT_MASK_ALL_INTS 0x02
+#define SCA3000_INT_MASK_ACTIVE_HIGH 0x01
+#define SCA3000_INT_MASK_ACTIVE_LOW 0x00
+
+/* Values of multiplexed registers (write to ctrl_data after select) */
+#define SCA3000_REG_ADDR_CTRL_DATA 0x22
+
+/*
+ * Measurement modes available on some sca3000 series chips. Code assumes others
+ * may become available in the future.
+ *
+ * Bypass - Bypass the low-pass filter in the signal channel so as to increase
+ * signal bandwidth.
+ *
+ * Narrow - Narrow low-pass filtering of the signal channel and half output
+ * data rate by decimation.
+ *
+ * Wide - Widen low-pass filtering of signal channel to increase bandwidth
+ */
+#define SCA3000_OP_MODE_BYPASS 0x01
+#define SCA3000_OP_MODE_NARROW 0x02
+#define SCA3000_OP_MODE_WIDE 0x04
+#define SCA3000_MAX_TX 6
+#define SCA3000_MAX_RX 2
+
+/**
+ * struct sca3000_state - device instance state information
+ * @us: the associated spi device
+ * @info: chip variant information
+ * @interrupt_handler_ws: event interrupt handler for all events
+ * @last_timestamp: the timestamp of the last event
+ * @mo_det_use_count: reference counter for the motion detection unit
+ * @lock: lock used to protect elements of sca3000_state
+ * and the underlying device state.
+ * @bpse: number of bits per scan element
+ * @tx: dma-able transmit buffer
+ * @rx: dma-able receive buffer
+ **/
+struct sca3000_state {
+ struct spi_device *us;
+ const struct sca3000_chip_info *info;
+ struct work_struct interrupt_handler_ws;
+ s64 last_timestamp;
+ int mo_det_use_count;
+ struct mutex lock;
+ int bpse;
+ /* Can these share a cacheline ? */
+ u8 rx[2] ____cacheline_aligned;
+ u8 tx[6] ____cacheline_aligned;
+};
+
+/**
+ * struct sca3000_chip_info - model dependent parameters
+ * @scale: scale * 10^-6
+ * @temp_output: some devices have temperature sensors.
+ * @measurement_mode_freq: normal mode sampling frequency
+ * @option_mode_1: first optional mode. Not all models have one
+ * @option_mode_1_freq: option mode 1 sampling frequency
+ * @option_mode_2: second optional mode. Not all chips have one
+ * @option_mode_2_freq: option mode 2 sampling frequency
+ *
+ * This structure is used to hold information about the functionality of a given
+ * sca3000 variant.
+ **/
+struct sca3000_chip_info {
+ unsigned int scale;
+ bool temp_output;
+ int measurement_mode_freq;
+ int option_mode_1;
+ int option_mode_1_freq;
+ int option_mode_2;
+ int option_mode_2_freq;
+ int mot_det_mult_xz[6];
+ int mot_det_mult_y[7];
+};
enum sca3000_variant {
d01,
},
};
-int sca3000_write_reg(struct sca3000_state *st, u8 address, u8 val)
+static int sca3000_write_reg(struct sca3000_state *st, u8 address, u8 val)
{
st->tx[0] = SCA3000_WRITE_REG(address);
st->tx[1] = val;
return spi_write(st->us, st->tx, 2);
}
-int sca3000_read_data_short(struct sca3000_state *st,
+static int sca3000_read_data_short(struct sca3000_state *st,
u8 reg_address_high,
int len)
{
.attrs = sca3000_attributes,
};
+/**
+ * sca3000_ring_int_process() ring specific interrupt handling.
+ *
+ * This is only split from the main interrupt handler so as to
+ * reduce the amount of code if the ring buffer is not enabled.
+ **/
+static void sca3000_ring_int_process(u8 val, struct iio_buffer *ring)
+{
+ if (val & (SCA3000_INT_STATUS_THREE_QUARTERS |
+ SCA3000_INT_STATUS_HALF)) {
+ ring->stufftoread = true;
+ wake_up_interruptible(&ring->pollq);
+ }
+}
+
/**
* sca3000_event_handler() - handling ring and non ring events
*
.name = "events",
};
+static int sca3000_read_data(struct sca3000_state *st,
+ u8 reg_address_high,
+ u8 **rx_p,
+ int len)
+{
+ int ret;
+ struct spi_transfer xfer[2] = {
+ {
+ .len = 1,
+ .tx_buf = st->tx,
+ }, {
+ .len = len,
+ }
+ };
+ *rx_p = kmalloc(len, GFP_KERNEL);
+ if (!*rx_p) {
+ ret = -ENOMEM;
+ goto error_ret;
+ }
+ xfer[1].rx_buf = *rx_p;
+ st->tx[0] = SCA3000_READ_REG(reg_address_high);
+ ret = spi_sync_transfer(st->us, xfer, ARRAY_SIZE(xfer));
+ if (ret) {
+ dev_err(get_device(&st->us->dev), "problem reading register");
+ goto error_free_rx;
+ }
+
+ return 0;
+error_free_rx:
+ kfree(*rx_p);
+error_ret:
+ return ret;
+}
+
+/**
+ * sca3000_read_first_n_hw_rb() - main ring access, pulls data from ring
+ * @r: the ring
+ * @count: number of samples to try and pull
+ * @data: output the actual samples pulled from the hw ring
+ *
+ * Currently does not provide timestamps. As the hardware doesn't add them they
+ * can only be inferred approximately from ring buffer events such as 50% full
+ * and knowledge of when buffer was last emptied. This is left to userspace.
+ **/
+static int sca3000_read_first_n_hw_rb(struct iio_buffer *r,
+ size_t count, char __user *buf)
+{
+ struct iio_hw_buffer *hw_ring = iio_to_hw_buf(r);
+ struct iio_dev *indio_dev = hw_ring->private;
+ struct sca3000_state *st = iio_priv(indio_dev);
+ u8 *rx;
+ int ret, i, num_available, num_read = 0;
+ int bytes_per_sample = 1;
+
+ if (st->bpse == 11)
+ bytes_per_sample = 2;
+
+ mutex_lock(&st->lock);
+ if (count % bytes_per_sample) {
+ ret = -EINVAL;
+ goto error_ret;
+ }
+
+ ret = sca3000_read_data_short(st, SCA3000_REG_ADDR_BUF_COUNT, 1);
+ if (ret)
+ goto error_ret;
+ num_available = st->rx[0];
+ /*
+ * num_available is the total number of samples available
+ * i.e. number of time points * number of channels.
+ */
+ if (count > num_available * bytes_per_sample)
+ num_read = num_available * bytes_per_sample;
+ else
+ num_read = count;
+
+ ret = sca3000_read_data(st,
+ SCA3000_REG_ADDR_RING_OUT,
+ &rx, num_read);
+ if (ret)
+ goto error_ret;
+
+ for (i = 0; i < num_read / sizeof(u16); i++)
+ *(((u16 *)rx) + i) = be16_to_cpup((__be16 *)rx + i);
+
+ if (copy_to_user(buf, rx, num_read))
+ ret = -EFAULT;
+ kfree(rx);
+ r->stufftoread = 0;
+error_ret:
+ mutex_unlock(&st->lock);
+
+ return ret ? ret : num_read;
+}
+
+static size_t sca3000_ring_buf_data_available(struct iio_buffer *r)
+{
+ return r->stufftoread ? r->watermark : 0;
+}
+
+/**
+ * sca3000_query_ring_int() is the hardware ring status interrupt enabled
+ **/
+static ssize_t sca3000_query_ring_int(struct device *dev,
+ struct device_attribute *attr,
+ char *buf)
+{
+ struct iio_dev_attr *this_attr = to_iio_dev_attr(attr);
+ int ret, val;
+ struct iio_dev *indio_dev = dev_to_iio_dev(dev);
+ struct sca3000_state *st = iio_priv(indio_dev);
+
+ mutex_lock(&st->lock);
+ ret = sca3000_read_data_short(st, SCA3000_REG_ADDR_INT_MASK, 1);
+ val = st->rx[0];
+ mutex_unlock(&st->lock);
+ if (ret)
+ return ret;
+
+ return sprintf(buf, "%d\n", !!(val & this_attr->address));
+}
+
+/**
+ * sca3000_set_ring_int() set state of ring status interrupt
+ **/
+static ssize_t sca3000_set_ring_int(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf,
+ size_t len)
+{
+ struct iio_dev *indio_dev = dev_to_iio_dev(dev);
+ struct sca3000_state *st = iio_priv(indio_dev);
+ struct iio_dev_attr *this_attr = to_iio_dev_attr(attr);
+ u8 val;
+ int ret;
+
+ mutex_lock(&st->lock);
+ ret = kstrtou8(buf, 10, &val);
+ if (ret)
+ goto error_ret;
+ ret = sca3000_read_data_short(st, SCA3000_REG_ADDR_INT_MASK, 1);
+ if (ret)
+ goto error_ret;
+ if (val)
+ ret = sca3000_write_reg(st,
+ SCA3000_REG_ADDR_INT_MASK,
+ st->rx[0] | this_attr->address);
+ else
+ ret = sca3000_write_reg(st,
+ SCA3000_REG_ADDR_INT_MASK,
+ st->rx[0] & ~this_attr->address);
+error_ret:
+ mutex_unlock(&st->lock);
+
+ return ret ? ret : len;
+}
+
+static IIO_DEVICE_ATTR(50_percent, S_IRUGO | S_IWUSR,
+ sca3000_query_ring_int,
+ sca3000_set_ring_int,
+ SCA3000_INT_MASK_RING_HALF);
+
+static IIO_DEVICE_ATTR(75_percent, S_IRUGO | S_IWUSR,
+ sca3000_query_ring_int,
+ sca3000_set_ring_int,
+ SCA3000_INT_MASK_RING_THREE_QUARTER);
+
+static ssize_t sca3000_show_buffer_scale(struct device *dev,
+ struct device_attribute *attr,
+ char *buf)
+{
+ struct iio_dev *indio_dev = dev_to_iio_dev(dev);
+ struct sca3000_state *st = iio_priv(indio_dev);
+
+ return sprintf(buf, "0.%06d\n", 4 * st->info->scale);
+}
+
+static IIO_DEVICE_ATTR(in_accel_scale,
+ S_IRUGO,
+ sca3000_show_buffer_scale,
+ NULL,
+ 0);
+
+/*
+ * Ring buffer attributes
+ * This device is a bit unusual in that the sampling frequency and bpse
+ * only apply to the ring buffer. At all times full rate and accuracy
+ * is available via direct reading from registers.
+ */
+static const struct attribute *sca3000_ring_attributes[] = {
+ &iio_dev_attr_50_percent.dev_attr.attr,
+ &iio_dev_attr_75_percent.dev_attr.attr,
+ &iio_dev_attr_in_accel_scale.dev_attr.attr,
+ NULL,
+};
+
+static struct iio_buffer *sca3000_rb_allocate(struct iio_dev *indio_dev)
+{
+ struct iio_buffer *buf;
+ struct iio_hw_buffer *ring;
+
+ ring = kzalloc(sizeof(*ring), GFP_KERNEL);
+ if (!ring)
+ return NULL;
+
+ ring->private = indio_dev;
+ buf = &ring->buf;
+ buf->stufftoread = 0;
+ buf->length = 64;
+ buf->attrs = sca3000_ring_attributes;
+ iio_buffer_init(buf);
+
+ return buf;
+}
+
+static void sca3000_ring_release(struct iio_buffer *r)
+{
+ kfree(iio_to_hw_buf(r));
+}
+
+static const struct iio_buffer_access_funcs sca3000_ring_access_funcs = {
+ .read_first_n = &sca3000_read_first_n_hw_rb,
+ .data_available = sca3000_ring_buf_data_available,
+ .release = sca3000_ring_release,
+
+ .modes = INDIO_BUFFER_HARDWARE,
+};
+
+static int sca3000_configure_ring(struct iio_dev *indio_dev)
+{
+ struct iio_buffer *buffer;
+
+ buffer = sca3000_rb_allocate(indio_dev);
+ if (!buffer)
+ return -ENOMEM;
+ indio_dev->modes |= INDIO_BUFFER_HARDWARE;
+
+ buffer->access = &sca3000_ring_access_funcs;
+ iio_device_attach_buffer(indio_dev, buffer);
+
+ return 0;
+}
+
+static void sca3000_unconfigure_ring(struct iio_dev *indio_dev)
+{
+ iio_buffer_put(indio_dev->buffer);
+}
+
+static inline
+int __sca3000_hw_ring_state_set(struct iio_dev *indio_dev, bool state)
+{
+ struct sca3000_state *st = iio_priv(indio_dev);
+ int ret;
+
+ mutex_lock(&st->lock);
+ ret = sca3000_read_data_short(st, SCA3000_REG_ADDR_MODE, 1);
+ if (ret)
+ goto error_ret;
+ if (state) {
+ dev_info(&indio_dev->dev, "supposedly enabling ring buffer\n");
+ ret = sca3000_write_reg(st,
+ SCA3000_REG_ADDR_MODE,
+ (st->rx[0] | SCA3000_RING_BUF_ENABLE));
+ } else
+ ret = sca3000_write_reg(st,
+ SCA3000_REG_ADDR_MODE,
+ (st->rx[0] & ~SCA3000_RING_BUF_ENABLE));
+error_ret:
+ mutex_unlock(&st->lock);
+
+ return ret;
+}
+
+/**
+ * sca3000_hw_ring_preenable() hw ring buffer preenable function
+ *
+ * Very simple enable function as the chip will allows normal reads
+ * during ring buffer operation so as long as it is indeed running
+ * before we notify the core, the precise ordering does not matter.
+ **/
+static int sca3000_hw_ring_preenable(struct iio_dev *indio_dev)
+{
+ return __sca3000_hw_ring_state_set(indio_dev, 1);
+}
+
+static int sca3000_hw_ring_postdisable(struct iio_dev *indio_dev)
+{
+ return __sca3000_hw_ring_state_set(indio_dev, 0);
+}
+
+static const struct iio_buffer_setup_ops sca3000_ring_setup_ops = {
+ .preenable = &sca3000_hw_ring_preenable,
+ .postdisable = &sca3000_hw_ring_postdisable,
+};
+
+static void sca3000_register_ring_funcs(struct iio_dev *indio_dev)
+{
+ indio_dev->setup_ops = &sca3000_ring_setup_ops;
+}
+
/**
* sca3000_clean_setup() get the device into a predictable state
*
+++ /dev/null
-/*
- * sca3000.c -- support VTI sca3000 series accelerometers
- * via SPI
- *
- * Copyright (c) 2007 Jonathan Cameron <jic23@kernel.org>
- *
- * Partly based upon tle62x0.c
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * Initial mode is direct measurement.
- *
- * Untested things
- *
- * Temperature reading (the e05 I'm testing with doesn't have a sensor)
- *
- * Free fall detection mode - supported but untested as I'm not droping my
- * dubious wire rig far enough to test it.
- *
- * Unsupported as yet
- *
- * Time stamping of data from ring. Various ideas on how to do this but none
- * are remotely simple. Suggestions welcome.
- *
- * Individual enabling disabling of channels going into ring buffer
- *
- * Overflow handling (this is signaled for all but 8 bit ring buffer mode.)
- *
- * Motion detector using AND combinations of signals.
- *
- * Note: Be very careful about not touching an register bytes marked
- * as reserved on the data sheet. They really mean it as changing convents of
- * some will cause the device to lock up.
- *
- * Known issues - on rare occasions the interrupts lock up. Not sure why as yet.
- * Can probably alleviate this by reading the interrupt register on start, but
- * that is really just brushing the problem under the carpet.
- */
-#ifndef _SCA3000
-#define _SCA3000
-
-#define SCA3000_WRITE_REG(a) (((a) << 2) | 0x02)
-#define SCA3000_READ_REG(a) ((a) << 2)
-
-#define SCA3000_REG_ADDR_REVID 0x00
-#define SCA3000_REVID_MAJOR_MASK 0xf0
-#define SCA3000_REVID_MINOR_MASK 0x0f
-
-#define SCA3000_REG_ADDR_STATUS 0x02
-#define SCA3000_LOCKED 0x20
-#define SCA3000_EEPROM_CS_ERROR 0x02
-#define SCA3000_SPI_FRAME_ERROR 0x01
-
-/* All reads done using register decrement so no need to directly access LSBs */
-#define SCA3000_REG_ADDR_X_MSB 0x05
-#define SCA3000_REG_ADDR_Y_MSB 0x07
-#define SCA3000_REG_ADDR_Z_MSB 0x09
-
-#define SCA3000_REG_ADDR_RING_OUT 0x0f
-
-/* Temp read untested - the e05 doesn't have the sensor */
-#define SCA3000_REG_ADDR_TEMP_MSB 0x13
-
-#define SCA3000_REG_ADDR_MODE 0x14
-#define SCA3000_MODE_PROT_MASK 0x28
-
-#define SCA3000_RING_BUF_ENABLE 0x80
-#define SCA3000_RING_BUF_8BIT 0x40
-/*
- * Free fall detection triggers an interrupt if the acceleration
- * is below a threshold for equivalent of 25cm drop
- */
-#define SCA3000_FREE_FALL_DETECT 0x10
-#define SCA3000_MEAS_MODE_NORMAL 0x00
-#define SCA3000_MEAS_MODE_OP_1 0x01
-#define SCA3000_MEAS_MODE_OP_2 0x02
-
-/*
- * In motion detection mode the accelerations are band pass filtered
- * (approx 1 - 25Hz) and then a programmable threshold used to trigger
- * and interrupt.
- */
-#define SCA3000_MEAS_MODE_MOT_DET 0x03
-
-#define SCA3000_REG_ADDR_BUF_COUNT 0x15
-
-#define SCA3000_REG_ADDR_INT_STATUS 0x16
-
-#define SCA3000_INT_STATUS_THREE_QUARTERS 0x80
-#define SCA3000_INT_STATUS_HALF 0x40
-
-#define SCA3000_INT_STATUS_FREE_FALL 0x08
-#define SCA3000_INT_STATUS_Y_TRIGGER 0x04
-#define SCA3000_INT_STATUS_X_TRIGGER 0x02
-#define SCA3000_INT_STATUS_Z_TRIGGER 0x01
-
-/* Used to allow access to multiplexed registers */
-#define SCA3000_REG_ADDR_CTRL_SEL 0x18
-/* Only available for SCA3000-D03 and SCA3000-D01 */
-#define SCA3000_REG_CTRL_SEL_I2C_DISABLE 0x01
-#define SCA3000_REG_CTRL_SEL_MD_CTRL 0x02
-#define SCA3000_REG_CTRL_SEL_MD_Y_TH 0x03
-#define SCA3000_REG_CTRL_SEL_MD_X_TH 0x04
-#define SCA3000_REG_CTRL_SEL_MD_Z_TH 0x05
-/*
- * BE VERY CAREFUL WITH THIS, IF 3 BITS ARE NOT SET the device
- * will not function
- */
-#define SCA3000_REG_CTRL_SEL_OUT_CTRL 0x0B
-#define SCA3000_OUT_CTRL_PROT_MASK 0xE0
-#define SCA3000_OUT_CTRL_BUF_X_EN 0x10
-#define SCA3000_OUT_CTRL_BUF_Y_EN 0x08
-#define SCA3000_OUT_CTRL_BUF_Z_EN 0x04
-#define SCA3000_OUT_CTRL_BUF_DIV_MASK 0x03
-#define SCA3000_OUT_CTRL_BUF_DIV_4 0x02
-#define SCA3000_OUT_CTRL_BUF_DIV_2 0x01
-
-/*
- * Control which motion detector interrupts are on.
- * For now only OR combinations are supported.
- */
-#define SCA3000_MD_CTRL_PROT_MASK 0xC0
-#define SCA3000_MD_CTRL_OR_Y 0x01
-#define SCA3000_MD_CTRL_OR_X 0x02
-#define SCA3000_MD_CTRL_OR_Z 0x04
-/* Currently unsupported */
-#define SCA3000_MD_CTRL_AND_Y 0x08
-#define SCA3000_MD_CTRL_AND_X 0x10
-#define SAC3000_MD_CTRL_AND_Z 0x20
-
-/*
- * Some control registers of complex access methods requiring this register to
- * be used to remove a lock.
- */
-#define SCA3000_REG_ADDR_UNLOCK 0x1e
-
-#define SCA3000_REG_ADDR_INT_MASK 0x21
-#define SCA3000_INT_MASK_PROT_MASK 0x1C
-
-#define SCA3000_INT_MASK_RING_THREE_QUARTER 0x80
-#define SCA3000_INT_MASK_RING_HALF 0x40
-
-#define SCA3000_INT_MASK_ALL_INTS 0x02
-#define SCA3000_INT_MASK_ACTIVE_HIGH 0x01
-#define SCA3000_INT_MASK_ACTIVE_LOW 0x00
-
-/* Values of multiplexed registers (write to ctrl_data after select) */
-#define SCA3000_REG_ADDR_CTRL_DATA 0x22
-
-/*
- * Measurement modes available on some sca3000 series chips. Code assumes others
- * may become available in the future.
- *
- * Bypass - Bypass the low-pass filter in the signal channel so as to increase
- * signal bandwidth.
- *
- * Narrow - Narrow low-pass filtering of the signal channel and half output
- * data rate by decimation.
- *
- * Wide - Widen low-pass filtering of signal channel to increase bandwidth
- */
-#define SCA3000_OP_MODE_BYPASS 0x01
-#define SCA3000_OP_MODE_NARROW 0x02
-#define SCA3000_OP_MODE_WIDE 0x04
-#define SCA3000_MAX_TX 6
-#define SCA3000_MAX_RX 2
-
-/**
- * struct sca3000_state - device instance state information
- * @us: the associated spi device
- * @info: chip variant information
- * @interrupt_handler_ws: event interrupt handler for all events
- * @last_timestamp: the timestamp of the last event
- * @mo_det_use_count: reference counter for the motion detection unit
- * @lock: lock used to protect elements of sca3000_state
- * and the underlying device state.
- * @bpse: number of bits per scan element
- * @tx: dma-able transmit buffer
- * @rx: dma-able receive buffer
- **/
-struct sca3000_state {
- struct spi_device *us;
- const struct sca3000_chip_info *info;
- struct work_struct interrupt_handler_ws;
- s64 last_timestamp;
- int mo_det_use_count;
- struct mutex lock;
- int bpse;
- /* Can these share a cacheline ? */
- u8 rx[2] ____cacheline_aligned;
- u8 tx[6] ____cacheline_aligned;
-};
-
-/**
- * struct sca3000_chip_info - model dependent parameters
- * @scale: scale * 10^-6
- * @temp_output: some devices have temperature sensors.
- * @measurement_mode_freq: normal mode sampling frequency
- * @option_mode_1: first optional mode. Not all models have one
- * @option_mode_1_freq: option mode 1 sampling frequency
- * @option_mode_2: second optional mode. Not all chips have one
- * @option_mode_2_freq: option mode 2 sampling frequency
- *
- * This structure is used to hold information about the functionality of a given
- * sca3000 variant.
- **/
-struct sca3000_chip_info {
- unsigned int scale;
- bool temp_output;
- int measurement_mode_freq;
- int option_mode_1;
- int option_mode_1_freq;
- int option_mode_2;
- int option_mode_2_freq;
- int mot_det_mult_xz[6];
- int mot_det_mult_y[7];
-};
-
-int sca3000_read_data_short(struct sca3000_state *st,
- u8 reg_address_high,
- int len);
-
-/**
- * sca3000_write_reg() write a single register
- * @address: address of register on chip
- * @val: value to be written to register
- *
- * The main lock must be held.
- **/
-int sca3000_write_reg(struct sca3000_state *st, u8 address, u8 val);
-
-#ifdef CONFIG_IIO_BUFFER
-/**
- * sca3000_register_ring_funcs() setup the ring state change functions
- **/
-void sca3000_register_ring_funcs(struct iio_dev *indio_dev);
-
-/**
- * sca3000_configure_ring() - allocate and configure ring buffer
- * @indio_dev: iio-core device whose ring is to be configured
- *
- * The hardware ring buffer needs far fewer ring buffer functions than
- * a software one as a lot of things are handled automatically.
- * This function also tells the iio core that our device supports a
- * hardware ring buffer mode.
- **/
-int sca3000_configure_ring(struct iio_dev *indio_dev);
-
-/**
- * sca3000_unconfigure_ring() - deallocate the ring buffer
- * @indio_dev: iio-core device whose ring we are freeing
- **/
-void sca3000_unconfigure_ring(struct iio_dev *indio_dev);
-
-/**
- * sca3000_ring_int_process() handles ring related event pushing and escalation
- * @val: the event code
- **/
-void sca3000_ring_int_process(u8 val, struct iio_buffer *ring);
-
-#else
-static inline void sca3000_register_ring_funcs(struct iio_dev *indio_dev)
-{
-}
-
-static inline
-int sca3000_register_ring_access_and_init(struct iio_dev *indio_dev)
-{
- return 0;
-}
-
-static inline void sca3000_ring_int_process(u8 val, void *ring)
-{
-}
-
-#endif
-#endif /* _SCA3000 */
+++ /dev/null
-/*
- * sca3000_ring.c -- support VTI sca3000 series accelerometers via SPI
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License version 2 as published by
- * the Free Software Foundation.
- *
- * Copyright (c) 2009 Jonathan Cameron <jic23@kernel.org>
- *
- */
-
-#include <linux/interrupt.h>
-#include <linux/fs.h>
-#include <linux/slab.h>
-#include <linux/kernel.h>
-#include <linux/spi/spi.h>
-#include <linux/sysfs.h>
-#include <linux/sched.h>
-#include <linux/poll.h>
-
-#include <linux/iio/iio.h>
-#include <linux/iio/sysfs.h>
-#include <linux/iio/buffer.h>
-#include "../ring_hw.h"
-#include "sca3000.h"
-
-/* RFC / future work
- *
- * The internal ring buffer doesn't actually change what it holds depending
- * on which signals are enabled etc, merely whether you can read them.
- * As such the scan mode selection is somewhat different than for a software
- * ring buffer and changing it actually covers any data already in the buffer.
- * Currently scan elements aren't configured so it doesn't matter.
- */
-
-static int sca3000_read_data(struct sca3000_state *st,
- u8 reg_address_high,
- u8 **rx_p,
- int len)
-{
- int ret;
- struct spi_transfer xfer[2] = {
- {
- .len = 1,
- .tx_buf = st->tx,
- }, {
- .len = len,
- }
- };
- *rx_p = kmalloc(len, GFP_KERNEL);
- if (!*rx_p) {
- ret = -ENOMEM;
- goto error_ret;
- }
- xfer[1].rx_buf = *rx_p;
- st->tx[0] = SCA3000_READ_REG(reg_address_high);
- ret = spi_sync_transfer(st->us, xfer, ARRAY_SIZE(xfer));
- if (ret) {
- dev_err(get_device(&st->us->dev), "problem reading register");
- goto error_free_rx;
- }
-
- return 0;
-error_free_rx:
- kfree(*rx_p);
-error_ret:
- return ret;
-}
-
-/**
- * sca3000_read_first_n_hw_rb() - main ring access, pulls data from ring
- * @r: the ring
- * @count: number of samples to try and pull
- * @data: output the actual samples pulled from the hw ring
- *
- * Currently does not provide timestamps. As the hardware doesn't add them they
- * can only be inferred approximately from ring buffer events such as 50% full
- * and knowledge of when buffer was last emptied. This is left to userspace.
- **/
-static int sca3000_read_first_n_hw_rb(struct iio_buffer *r,
- size_t count, char __user *buf)
-{
- struct iio_hw_buffer *hw_ring = iio_to_hw_buf(r);
- struct iio_dev *indio_dev = hw_ring->private;
- struct sca3000_state *st = iio_priv(indio_dev);
- u8 *rx;
- int ret, i, num_available, num_read = 0;
- int bytes_per_sample = 1;
-
- if (st->bpse == 11)
- bytes_per_sample = 2;
-
- mutex_lock(&st->lock);
- if (count % bytes_per_sample) {
- ret = -EINVAL;
- goto error_ret;
- }
-
- ret = sca3000_read_data_short(st, SCA3000_REG_ADDR_BUF_COUNT, 1);
- if (ret)
- goto error_ret;
- num_available = st->rx[0];
- /*
- * num_available is the total number of samples available
- * i.e. number of time points * number of channels.
- */
- if (count > num_available * bytes_per_sample)
- num_read = num_available * bytes_per_sample;
- else
- num_read = count;
-
- ret = sca3000_read_data(st,
- SCA3000_REG_ADDR_RING_OUT,
- &rx, num_read);
- if (ret)
- goto error_ret;
-
- for (i = 0; i < num_read / sizeof(u16); i++)
- *(((u16 *)rx) + i) = be16_to_cpup((__be16 *)rx + i);
-
- if (copy_to_user(buf, rx, num_read))
- ret = -EFAULT;
- kfree(rx);
- r->stufftoread = 0;
-error_ret:
- mutex_unlock(&st->lock);
-
- return ret ? ret : num_read;
-}
-
-static size_t sca3000_ring_buf_data_available(struct iio_buffer *r)
-{
- return r->stufftoread ? r->watermark : 0;
-}
-
-/**
- * sca3000_query_ring_int() is the hardware ring status interrupt enabled
- **/
-static ssize_t sca3000_query_ring_int(struct device *dev,
- struct device_attribute *attr,
- char *buf)
-{
- struct iio_dev_attr *this_attr = to_iio_dev_attr(attr);
- int ret, val;
- struct iio_dev *indio_dev = dev_to_iio_dev(dev);
- struct sca3000_state *st = iio_priv(indio_dev);
-
- mutex_lock(&st->lock);
- ret = sca3000_read_data_short(st, SCA3000_REG_ADDR_INT_MASK, 1);
- val = st->rx[0];
- mutex_unlock(&st->lock);
- if (ret)
- return ret;
-
- return sprintf(buf, "%d\n", !!(val & this_attr->address));
-}
-
-/**
- * sca3000_set_ring_int() set state of ring status interrupt
- **/
-static ssize_t sca3000_set_ring_int(struct device *dev,
- struct device_attribute *attr,
- const char *buf,
- size_t len)
-{
- struct iio_dev *indio_dev = dev_to_iio_dev(dev);
- struct sca3000_state *st = iio_priv(indio_dev);
- struct iio_dev_attr *this_attr = to_iio_dev_attr(attr);
- u8 val;
- int ret;
-
- mutex_lock(&st->lock);
- ret = kstrtou8(buf, 10, &val);
- if (ret)
- goto error_ret;
- ret = sca3000_read_data_short(st, SCA3000_REG_ADDR_INT_MASK, 1);
- if (ret)
- goto error_ret;
- if (val)
- ret = sca3000_write_reg(st,
- SCA3000_REG_ADDR_INT_MASK,
- st->rx[0] | this_attr->address);
- else
- ret = sca3000_write_reg(st,
- SCA3000_REG_ADDR_INT_MASK,
- st->rx[0] & ~this_attr->address);
-error_ret:
- mutex_unlock(&st->lock);
-
- return ret ? ret : len;
-}
-
-static IIO_DEVICE_ATTR(50_percent, S_IRUGO | S_IWUSR,
- sca3000_query_ring_int,
- sca3000_set_ring_int,
- SCA3000_INT_MASK_RING_HALF);
-
-static IIO_DEVICE_ATTR(75_percent, S_IRUGO | S_IWUSR,
- sca3000_query_ring_int,
- sca3000_set_ring_int,
- SCA3000_INT_MASK_RING_THREE_QUARTER);
-
-static ssize_t sca3000_show_buffer_scale(struct device *dev,
- struct device_attribute *attr,
- char *buf)
-{
- struct iio_dev *indio_dev = dev_to_iio_dev(dev);
- struct sca3000_state *st = iio_priv(indio_dev);
-
- return sprintf(buf, "0.%06d\n", 4 * st->info->scale);
-}
-
-static IIO_DEVICE_ATTR(in_accel_scale,
- S_IRUGO,
- sca3000_show_buffer_scale,
- NULL,
- 0);
-
-/*
- * Ring buffer attributes
- * This device is a bit unusual in that the sampling frequency and bpse
- * only apply to the ring buffer. At all times full rate and accuracy
- * is available via direct reading from registers.
- */
-static const struct attribute *sca3000_ring_attributes[] = {
- &iio_dev_attr_50_percent.dev_attr.attr,
- &iio_dev_attr_75_percent.dev_attr.attr,
- &iio_dev_attr_in_accel_scale.dev_attr.attr,
- NULL,
-};
-
-static struct iio_buffer *sca3000_rb_allocate(struct iio_dev *indio_dev)
-{
- struct iio_buffer *buf;
- struct iio_hw_buffer *ring;
-
- ring = kzalloc(sizeof(*ring), GFP_KERNEL);
- if (!ring)
- return NULL;
-
- ring->private = indio_dev;
- buf = &ring->buf;
- buf->stufftoread = 0;
- buf->length = 64;
- buf->attrs = sca3000_ring_attributes;
- iio_buffer_init(buf);
-
- return buf;
-}
-
-static void sca3000_ring_release(struct iio_buffer *r)
-{
- kfree(iio_to_hw_buf(r));
-}
-
-static const struct iio_buffer_access_funcs sca3000_ring_access_funcs = {
- .read_first_n = &sca3000_read_first_n_hw_rb,
- .data_available = sca3000_ring_buf_data_available,
- .release = sca3000_ring_release,
-
- .modes = INDIO_BUFFER_HARDWARE,
-};
-
-int sca3000_configure_ring(struct iio_dev *indio_dev)
-{
- struct iio_buffer *buffer;
-
- buffer = sca3000_rb_allocate(indio_dev);
- if (!buffer)
- return -ENOMEM;
- indio_dev->modes |= INDIO_BUFFER_HARDWARE;
-
-
- buffer->access = &sca3000_ring_access_funcs;
- iio_device_attach_buffer(indio_dev, buffer);
-
- return 0;
-}
-
-void sca3000_unconfigure_ring(struct iio_dev *indio_dev)
-{
- iio_buffer_put(indio_dev->buffer);
-}
-
-static inline
-int __sca3000_hw_ring_state_set(struct iio_dev *indio_dev, bool state)
-{
- struct sca3000_state *st = iio_priv(indio_dev);
- int ret;
-
- mutex_lock(&st->lock);
- ret = sca3000_read_data_short(st, SCA3000_REG_ADDR_MODE, 1);
- if (ret)
- goto error_ret;
- if (state) {
- dev_info(&indio_dev->dev, "supposedly enabling ring buffer\n");
- ret = sca3000_write_reg(st,
- SCA3000_REG_ADDR_MODE,
- (st->rx[0] | SCA3000_RING_BUF_ENABLE));
- } else
- ret = sca3000_write_reg(st,
- SCA3000_REG_ADDR_MODE,
- (st->rx[0] & ~SCA3000_RING_BUF_ENABLE));
-error_ret:
- mutex_unlock(&st->lock);
-
- return ret;
-}
-
-/**
- * sca3000_hw_ring_preenable() hw ring buffer preenable function
- *
- * Very simple enable function as the chip will allows normal reads
- * during ring buffer operation so as long as it is indeed running
- * before we notify the core, the precise ordering does not matter.
- **/
-static int sca3000_hw_ring_preenable(struct iio_dev *indio_dev)
-{
- return __sca3000_hw_ring_state_set(indio_dev, 1);
-}
-
-static int sca3000_hw_ring_postdisable(struct iio_dev *indio_dev)
-{
- return __sca3000_hw_ring_state_set(indio_dev, 0);
-}
-
-static const struct iio_buffer_setup_ops sca3000_ring_setup_ops = {
- .preenable = &sca3000_hw_ring_preenable,
- .postdisable = &sca3000_hw_ring_postdisable,
-};
-
-void sca3000_register_ring_funcs(struct iio_dev *indio_dev)
-{
- indio_dev->setup_ops = &sca3000_ring_setup_ops;
-}
-
-/**
- * sca3000_ring_int_process() ring specific interrupt handling.
- *
- * This is only split from the main interrupt handler so as to
- * reduce the amount of code if the ring buffer is not enabled.
- **/
-void sca3000_ring_int_process(u8 val, struct iio_buffer *ring)
-{
- if (val & (SCA3000_INT_STATUS_THREE_QUARTERS |
- SCA3000_INT_STATUS_HALF)) {
- ring->stufftoread = true;
- wake_up_interruptible(&ring->pollq);
- }
-}