mtd: nand: omap: Documentation: How to select correct ECC scheme for your device ?

- Adds DT binding property for BCH16 ECC scheme
 - Adds describes on factors which determine choice of ECC scheme for particular device

CC: devicetree@vger.kernel.org
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt
index 5e1f31b5ff70d19549e9ac2d89f186f90dc85a89..eb81435ea15a3fe00e8e0edb4ea5c8784579d28d 100644 (file)
--- a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt
@@ -28,6 +28,8 @@ Optional properties:
                "ham1"          1-bit Hamming ecc code
                "bch4"          4-bit BCH ecc code
                "bch8"          8-bit BCH ecc code
+               "bch16"         16-bit BCH ECC code
+               Refer below "How to select correct ECC scheme for your device ?"
 
  - ti,nand-xfer-type:          A string setting the data transfer type. One of:
 
@@ -90,3 +92,46 @@ Example for an AM33xx board:
                };
        };
 
+How to select correct ECC scheme for your device ?
+--------------------------------------------------
+Higher ECC scheme usually means better protection against bit-flips and
+increased system lifetime. However, selection of ECC scheme is dependent
+on various other factors also like;
+
+(1) support of built in hardware engines.
+       Some legacy OMAP SoC do not have ELM harware engine, so those SoC cannot
+       support ecc-schemes with hardware error-correction (BCHx_HW). However
+       such SoC can use ecc-schemes with software library for error-correction
+       (BCHx_HW_DETECTION_SW). The error correction capability with software
+       library remains equivalent to their hardware counter-part, but there is
+       slight CPU penalty when too many bit-flips are detected during reads.
+
+(2) Device parameters like OOBSIZE.
+       Other factor which governs the selection of ecc-scheme is oob-size.
+       Higher ECC schemes require more OOB/Spare area to store ECC syndrome,
+       so the device should have enough free bytes available its OOB/Spare
+       area to accomodate ECC for entire page. In general following expression
+       helps in determining if given device can accomodate ECC syndrome:
+       "2 + (PAGESIZE / 512) * ECC_BYTES" >= OOBSIZE"
+       where
+               OOBSIZE         number of bytes in OOB/spare area
+               PAGESIZE        number of bytes in main-area of device page
+               ECC_BYTES       number of ECC bytes generated to protect
+                               512 bytes of data, which is:
+                               '3' for HAM1_xx ecc schemes
+                               '7' for BCH4_xx ecc schemes
+                               '14' for BCH8_xx ecc schemes
+                               '26' for BCH16_xx ecc schemes
+
+       Example(a): For a device with PAGESIZE = 2048 and OOBSIZE = 64 and
+               trying to use BCH16 (ECC_BYTES=26) ecc-scheme.
+               Number of ECC bytes per page = (2 + (2048 / 512) * 26) = 106 B
+               which is greater than capacity of NAND device (OOBSIZE=64)
+               Hence, BCH16 cannot be supported on given device. But it can
+               probably use lower ecc-schemes like BCH8.
+
+       Example(b): For a device with PAGESIZE = 2048 and OOBSIZE = 128 and
+               trying to use BCH16 (ECC_BYTES=26) ecc-scheme.
+               Number of ECC bytes per page = (2 + (2048 / 512) * 26) = 106 B
+               which can be accomodate in the OOB/Spare area of this device
+               (OOBSIZE=128). So this device can use BCH16 ecc-scheme.