]> git.karo-electronics.de Git - linux-beck.git/commitdiff
ARM: dts: am43xx: add support for parallel NAND flash
authorPekon Gupta <pekon@ti.com>
Wed, 5 Feb 2014 13:28:34 +0000 (18:58 +0530)
committerTony Lindgren <tony@atomide.com>
Sun, 2 Mar 2014 18:15:54 +0000 (10:15 -0800)
This patch:
 - enables GPMC h/w and ELM h/w engine for AM43xx devices (am4372.dtsi)
 - adds pinmux and DT node for Micron 4K-paged x8 NAND device (MT29F4G08AB)
   present on following boards:

   am43x-epos-evm:
On this board, NAND Flash control lines are muxed with QSPI, Thus only
        one of the two can be used at a time. Selection is controlled by:
        (a) dynamically driving following GPIO pin from software
            GPMC_A0(GPIO) == 0 NAND is selected (default)
            GPMC_A0(GPIO) == 1 eMMC is selected

Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
arch/arm/boot/dts/am4372.dtsi
arch/arm/boot/dts/am43x-epos-evm.dts

index eb74ab82aa94005156880b347d1824d06a1d0fc5..a4555bedd713a3f73604187210b114a36780337d 100644 (file)
                               <&edma 11>;
                        dma-names = "tx", "rx";
                };
+
+               elm: elm@48080000 {
+                       compatible = "ti,am3352-elm";
+                       reg = <0x48080000 0x2000>;
+                       interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+                       ti,hwmods = "elm";
+                       clocks = <&l4ls_gclk>;
+                       clock-names = "fck";
+                       status = "disabled";
+               };
+
+               gpmc: gpmc@50000000 {
+                       compatible = "ti,am3352-gpmc";
+                       ti,hwmods = "gpmc";
+                       clocks = <&l3s_gclk>;
+                       clock-names = "fck";
+                       reg = <0x50000000 0x2000>;
+                       interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+                       gpmc,num-cs = <7>;
+                       gpmc,num-waitpins = <2>;
+                       #address-cells = <2>;
+                       #size-cells = <1>;
+                       status = "disabled";
+               };
        };
 };
 
index fbf9c4c7a94fe7f998346140d32540b6ebf3507f..15aa70822bdf8af3fe5f403584ec8322d2b992ff 100644 (file)
                                0x18c (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)    /* i2c0_scl.i2c0_scl */
                        >;
                };
+
+               nand_flash_x8: nand_flash_x8 {
+                       pinctrl-single,pins = <
+                               0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE7)  /* gpmc_a0.SELQSPIorNAND/GPIO */
+                               0x0  (PIN_INPUT_PULLDOWN | MUX_MODE0)   /* gpmc_ad0.gpmc_ad0 */
+                               0x4  (PIN_INPUT_PULLDOWN | MUX_MODE0)   /* gpmc_ad1.gpmc_ad1 */
+                               0x8  (PIN_INPUT_PULLDOWN | MUX_MODE0)   /* gpmc_ad2.gpmc_ad2 */
+                               0xc  (PIN_INPUT_PULLDOWN | MUX_MODE0)   /* gpmc_ad3.gpmc_ad3 */
+                               0x10 (PIN_INPUT_PULLDOWN | MUX_MODE0)   /* gpmc_ad4.gpmc_ad4 */
+                               0x14 (PIN_INPUT_PULLDOWN | MUX_MODE0)   /* gpmc_ad5.gpmc_ad5 */
+                               0x18 (PIN_INPUT_PULLDOWN | MUX_MODE0)   /* gpmc_ad6.gpmc_ad6 */
+                               0x1c (PIN_INPUT_PULLDOWN | MUX_MODE0)   /* gpmc_ad7.gpmc_ad7 */
+                               0x70 (PIN_INPUT_PULLUP | MUX_MODE0)     /* gpmc_wait0.gpmc_wait0 */
+                               0x74 (PIN_OUTPUT_PULLUP | MUX_MODE7)    /* gpmc_wpn.gpmc_wpn */
+                               0x7c (PIN_OUTPUT | MUX_MODE0)           /* gpmc_csn0.gpmc_csn0  */
+                               0x90 (PIN_OUTPUT | MUX_MODE0)           /* gpmc_advn_ale.gpmc_advn_ale */
+                               0x94 (PIN_OUTPUT | MUX_MODE0)           /* gpmc_oen_ren.gpmc_oen_ren */
+                               0x98 (PIN_OUTPUT | MUX_MODE0)           /* gpmc_wen.gpmc_wen */
+                               0x9c (PIN_OUTPUT | MUX_MODE0)           /* gpmc_be0n_cle.gpmc_be0n_cle */
+                       >;
+               };
        };
 
        matrix_keypad: matrix_keypad@0 {
 &gpio3 {
        status = "okay";
 };
+
+&elm {
+       status = "okay";
+};
+
+&gpmc {
+       status = "okay";
+       pinctrl-names = "default";
+       pinctrl-0 = <&nand_flash_x8>;
+       ranges = <0 0 0x08000000 0x10000000>;   /* CS0: NAND */
+       nand@0,0 {
+               reg = <0 0 0>; /* CS0, offset 0 */
+               ti,nand-ecc-opt = "bch8";
+               ti,elm-id = <&elm>;
+               nand-bus-width = <8>;
+               gpmc,device-width = <1>;
+               gpmc,sync-clk-ps = <0>;
+               gpmc,cs-on-ns = <0>;
+               gpmc,cs-rd-off-ns = <40>; /* tCEA + tCHZ + 1 */
+               gpmc,cs-wr-off-ns = <40>;
+               gpmc,adv-on-ns = <0>;  /* cs-on-ns */
+               gpmc,adv-rd-off-ns = <25>; /* min( tALH + tALS + 1) */
+               gpmc,adv-wr-off-ns = <25>; /* min( tALH + tALS + 1) */
+               gpmc,we-on-ns = <0>;   /* cs-on-ns */
+               gpmc,we-off-ns = <20>; /* we-on-time + tWP + 2 */
+               gpmc,oe-on-ns = <3>;  /* cs-on-ns + tRR + 2 */
+               gpmc,oe-off-ns = <30>; /* oe-on-ns + tRP + 2 */
+               gpmc,access-ns = <30>; /* tCEA + 4*/
+               gpmc,rd-cycle-ns = <40>;
+               gpmc,wr-cycle-ns = <40>;
+               gpmc,wait-on-read = "true";
+               gpmc,wait-on-write = "true";
+               gpmc,bus-turnaround-ns = <0>;
+               gpmc,cycle2cycle-delay-ns = <0>;
+               gpmc,clk-activation-ns = <0>;
+               gpmc,wait-monitoring-ns = <0>;
+               gpmc,wr-access-ns = <40>;
+               gpmc,wr-data-mux-bus-ns = <0>;
+               /* MTD partition table */
+               /* All SPL-* partitions are sized to minimal length
+                * which can be independently programmable. For
+                * NAND flash this is equal to size of erase-block */
+               #address-cells = <1>;
+               #size-cells = <1>;
+               partition@0 {
+                       label = "NAND.SPL";
+                       reg = <0x00000000 0x00040000>;
+               };
+               partition@1 {
+                       label = "NAND.SPL.backup1";
+                       reg = <0x00040000 0x00040000>;
+               };
+               partition@2 {
+                       label = "NAND.SPL.backup2";
+                       reg = <0x00080000 0x00040000>;
+               };
+               partition@3 {
+                       label = "NAND.SPL.backup3";
+                       reg = <0x000C0000 0x00040000>;
+               };
+               partition@4 {
+                       label = "NAND.u-boot-spl-os";
+                       reg = <0x00100000 0x00080000>;
+               };
+               partition@5 {
+                       label = "NAND.u-boot";
+                       reg = <0x00180000 0x00100000>;
+               };
+               partition@6 {
+                       label = "NAND.u-boot-env";
+                       reg = <0x00280000 0x00040000>;
+               };
+               partition@7 {
+                       label = "NAND.u-boot-env.backup1";
+                       reg = <0x002C0000 0x00040000>;
+               };
+               partition@8 {
+                       label = "NAND.kernel";
+                       reg = <0x00300000 0x00700000>;
+               };
+               partition@9 {
+                       label = "NAND.file-system";
+                       reg = <0x00800000 0x1F600000>;
+               };
+       };
+};