ALSA ALSA sound support is enabled.
APIC APIC support is enabled.
APM Advanced Power Management support is enabled.
+ ARM ARM architecture is enabled.
AVR32 AVR32 architecture is enabled.
AX25 Appropriate AX.25 support is enabled.
BLACKFIN Blackfin architecture is enabled.
EFI EFI Partitioning (GPT) is enabled
EIDE EIDE/ATAPI support is enabled.
FB The frame buffer device is enabled.
+ FTRACE Function tracing enabled.
GCOV GCOV profiling is enabled.
HW Appropriate hardware is enabled.
IA-64 IA-64 architecture is enabled.
Documentation/m68k/kernel-options.txt.
MCA MCA bus support is enabled.
MDA MDA console support is enabled.
+ MIPS MIPS architecture is enabled.
MOUSE Appropriate mouse support is enabled.
MSI Message Signaled Interrupts (PCI).
MTD MTD (Memory Technology Device) support is enabled.
SPARC Sparc architecture is enabled.
SWSUSP Software suspend (hibernation) is enabled.
SUSPEND System suspend states are enabled.
- FTRACE Function tracing enabled.
TPM TPM drivers are enabled.
TS Appropriate touchscreen support is enabled.
UMS USB Mass Storage support is enabled.
X86-64 X86-64 architecture is enabled.
More X86-64 boot options can be found in
Documentation/x86/x86_64/boot-options.txt .
- X86 Either 32bit or 64bit x86 (same as X86-32+X86-64)
+ X86 Either 32-bit or 64-bit x86 (same as X86-32+X86-64)
XEN Xen support is enabled
In addition, the following text indicates that the option:
atkbd.softrepeat= [HW]
Use software keyboard repeat
- autotest [IA64]
+ autotest [IA-64]
baycom_epp= [HW,AX25]
Format: <io>,<mode>
uart[8250],mmio32,<addr>[,options]
Start an early, polled-mode console on the 8250/16550
UART at the specified I/O port or MMIO address.
- MMIO inter-register address stride is either 8bit (mmio)
- or 32bit (mmio32).
+ MMIO inter-register address stride is either 8-bit
+ (mmio) or 32-bit (mmio32).
The options are the same as for ttyS, above.
earlyprintk= [X86,SH,BLACKFIN]
See Documentation/block/as-iosched.txt and
Documentation/block/deadline-iosched.txt for details.
- elfcorehdr= [IA64,PPC,SH,X86]
+ elfcorehdr= [IA-64,PPC,SH,X86]
Specifies physical address of start of kernel core
image elf header. Generally kexec loader will
pass this option to capture kernel.
tracer at boot up. function-list is a comma separated
list of functions. This list can be changed at run
time by the set_ftrace_filter file in the debugfs
- tracing directory.
+ tracing directory.
ftrace_notrace=[function-list]
[FTRACE] Do not trace the functions specified in
hashdist= [KNL,NUMA] Large hashes allocated during boot
are distributed across NUMA nodes. Defaults on
- for 64bit NUMA, off otherwise.
+ for 64-bit NUMA, off otherwise.
Format: 0 | 1 (for off | on)
hcl= [IA-64] SGI's Hardware Graph compatibility layer
DMA.
forcedac [x86_64]
With this option iommu will not optimize to look
- for io virtual address below 32 bit forcing dual
+ for io virtual address below 32-bit forcing dual
address cycle on pci bus for cards supporting greater
- than 32 bit addressing. The default is to look
- for translation below 32 bit and if not available
+ than 32-bit addressing. The default is to look
+ for translation below 32-bit and if not available
then look in the higher range.
strict [Default Off]
With this option on every unmap_single operation will
off disable Interrupt Remapping
nosid disable Source ID checking
- inttest= [IA64]
+ inttest= [IA-64]
iomem= Disable strict checking of access to MMIO memory
strict regions from userspace.
nomerge
forcesac
soft
- pt [x86, IA64]
+ pt [x86, IA-64]
io7= [HW] IO7 for Marvel based alpha systems
See comment before marvel_specify_io7 in
kvm-amd.npt= [KVM,AMD] Disable nested paging (virtualized MMU)
for all guests.
- Default is 1 (enabled) if in 64bit or 32bit-PAE mode
+ Default is 1 (enabled) if in 64-bit or 32-bit PAE mode.
kvm-intel.bypass_guest_pf=
[KVM,Intel] Disables bypassing of guest page faults
libata.dma=0 Disable all PATA and SATA DMA
libata.dma=1 PATA and SATA Disk DMA only
libata.dma=2 ATAPI (CDROM) DMA only
- libata.dma=4 Compact Flash DMA only
+ libata.dma=4 Compact Flash DMA only
Combinations also work, so libata.dma=3 enables DMA
for disks and CDROMs, but not CFs.
-
+
libata.ignore_hpa= [LIBATA] Ignore HPA limit
libata.ignore_hpa=0 keep BIOS limits (default)
libata.ignore_hpa=1 ignore limits, using full disk
ltpc= [NET]
Format: <io>,<irq>,<dma>
- machvec= [IA64] Force the use of a particular machine-vector
+ machvec= [IA-64] Force the use of a particular machine-vector
(machvec) in a generic kernel.
Example: machvec=hpzx1_swiotlb
nointroute [IA-64]
- nojitter [IA64] Disables jitter checking for ITC timers.
+ nojitter [IA-64] Disables jitter checking for ITC timers.
no-kvmclock [X86,KVM] Disable paravirtualized KVM clock driver
nox2apic [X86-64,APIC] Do not enable x2APIC mode.
- nptcg= [IA64] Override max number of concurrent global TLB
+ nptcg= [IA-64] Override max number of concurrent global TLB
purges which is reported from either PAL_VM_SUMMARY or
SAL PALO.
Format: { parport<nr> | timid | 0 }
See also Documentation/parport.txt.
- pmtmr= [X86] Manual setup of pmtmr I/O Port.
+ pmtmr= [X86] Manual setup of pmtmr I/O Port.
Override pmtimer IOPort with a hex value.
e.g. pmtmr=0x508