From: Patrice Chotard Date: Tue, 8 Jan 2013 09:41:02 +0000 (+0100) Subject: pinctrl: add abx500 pinctrl driver core X-Git-Url: https://git.karo-electronics.de/?a=commitdiff_plain;h=0493e6493031523f78680b4469f02fc1b2d440f3;p=linux-beck.git pinctrl: add abx500 pinctrl driver core This adds the AB8500 core driver, which will be utilized by the follow-on drivers for different ABx500 variants. Sselect the driver from the DBX500_SOC, as this chip is powering and clocking that SoC. Cc: Samuel Ortiz Signed-off-by: Patrice Chotard Signed-off-by: Linus Walleij --- diff --git a/arch/arm/mach-ux500/Kconfig b/arch/arm/mach-ux500/Kconfig index 1d7dbe61a958..018bf681659d 100644 --- a/arch/arm/mach-ux500/Kconfig +++ b/arch/arm/mach-ux500/Kconfig @@ -11,6 +11,7 @@ config UX500_SOC_COMMON select COMMON_CLK select PINCTRL select PINCTRL_NOMADIK + select PINCTRL_ABX500 select PL310_ERRATA_753970 if CACHE_PL310 config UX500_SOC_DB8500 diff --git a/arch/arm/mach-ux500/board-mop500.c b/arch/arm/mach-ux500/board-mop500.c index d453522edb0d..b6f14ee507ca 100644 --- a/arch/arm/mach-ux500/board-mop500.c +++ b/arch/arm/mach-ux500/board-mop500.c @@ -90,26 +90,9 @@ static struct platform_device snowball_gpio_en_3v3_regulator_dev = { }, }; -static struct ab8500_gpio_platform_data ab8500_gpio_pdata = { +static struct abx500_gpio_platform_data ab8500_gpio_pdata = { .gpio_base = MOP500_AB8500_PIN_GPIO(1), .irq_base = MOP500_AB8500_VIR_GPIO_IRQ_BASE, - /* config_reg is the initial configuration of ab8500 pins. - * The pins can be configured as GPIO or alt functions based - * on value present in GpioSel1 to GpioSel6 and AlternatFunction - * register. This is the array of 7 configuration settings. - * One has to compile time decide these settings. Below is the - * explanation of these setting - * GpioSel1 = 0x00 => Pins GPIO1 to GPIO8 are not used as GPIO - * GpioSel2 = 0x1E => Pins GPIO10 to GPIO13 are configured as GPIO - * GpioSel3 = 0x80 => Pin GPIO24 is configured as GPIO - * GpioSel4 = 0x01 => Pin GPIo25 is configured as GPIO - * GpioSel5 = 0x7A => Pins GPIO34, GPIO36 to GPIO39 are conf as GPIO - * GpioSel6 = 0x00 => Pins GPIO41 & GPIo42 are not configured as GPIO - * AlternaFunction = 0x00 => If Pins GPIO10 to 13 are not configured - * as GPIO then this register selectes the alternate fucntions - */ - .config_reg = {0x00, 0x1E, 0x80, 0x01, - 0x7A, 0x00, 0x00}, }; /* ab8500-codec */ diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig index 881ddcd00236..ba3038c827c6 100644 --- a/drivers/pinctrl/Kconfig +++ b/drivers/pinctrl/Kconfig @@ -26,6 +26,13 @@ config DEBUG_PINCTRL help Say Y here to add some extra checks and diagnostics to PINCTRL calls. +config PINCTRL_ABX500 + bool "ST-Ericsson ABx500 family Mixed Signal Circuit gpio functions" + depends on AB8500_CORE + select GENERIC_PINCONF + help + Select this to enable the ABx500 family IC GPIO driver + config PINCTRL_AT91 bool "AT91 pinctrl driver" depends on OF diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile index e9ad8c3851be..ead4fa7dfd1f 100644 --- a/drivers/pinctrl/Makefile +++ b/drivers/pinctrl/Makefile @@ -9,6 +9,7 @@ ifeq ($(CONFIG_OF),y) obj-$(CONFIG_PINCTRL) += devicetree.o endif obj-$(CONFIG_GENERIC_PINCONF) += pinconf-generic.o +obj-$(CONFIG_PINCTRL_ABX500) += pinctrl-abx500.o obj-$(CONFIG_PINCTRL_AT91) += pinctrl-at91.o obj-$(CONFIG_PINCTRL_BCM2835) += pinctrl-bcm2835.o obj-$(CONFIG_PINCTRL_IMX) += pinctrl-imx.o diff --git a/drivers/pinctrl/pinctrl-abx500.c b/drivers/pinctrl/pinctrl-abx500.c new file mode 100644 index 000000000000..9eed9887da2a --- /dev/null +++ b/drivers/pinctrl/pinctrl-abx500.c @@ -0,0 +1,1233 @@ +/* + * Copyright (C) ST-Ericsson SA 2013 + * + * Author: Patrice Chotard + * License terms: GNU General Public License (GPL) version 2 + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include "pinctrl-abx500.h" + +/* + * The AB9540 and AB8540 GPIO support are extended versions + * of the AB8500 GPIO support. + * The AB9540 supports an additional (7th) register so that + * more GPIO may be configured and used. + * The AB8540 supports 4 new gpios (GPIOx_VBAT) that have + * internal pull-up and pull-down capabilities. + */ + +/* + * GPIO registers offset + * Bank: 0x10 + */ +#define AB8500_GPIO_SEL1_REG 0x00 +#define AB8500_GPIO_SEL2_REG 0x01 +#define AB8500_GPIO_SEL3_REG 0x02 +#define AB8500_GPIO_SEL4_REG 0x03 +#define AB8500_GPIO_SEL5_REG 0x04 +#define AB8500_GPIO_SEL6_REG 0x05 +#define AB9540_GPIO_SEL7_REG 0x06 + +#define AB8500_GPIO_DIR1_REG 0x10 +#define AB8500_GPIO_DIR2_REG 0x11 +#define AB8500_GPIO_DIR3_REG 0x12 +#define AB8500_GPIO_DIR4_REG 0x13 +#define AB8500_GPIO_DIR5_REG 0x14 +#define AB8500_GPIO_DIR6_REG 0x15 +#define AB9540_GPIO_DIR7_REG 0x16 + +#define AB8500_GPIO_OUT1_REG 0x20 +#define AB8500_GPIO_OUT2_REG 0x21 +#define AB8500_GPIO_OUT3_REG 0x22 +#define AB8500_GPIO_OUT4_REG 0x23 +#define AB8500_GPIO_OUT5_REG 0x24 +#define AB8500_GPIO_OUT6_REG 0x25 +#define AB9540_GPIO_OUT7_REG 0x26 + +#define AB8500_GPIO_PUD1_REG 0x30 +#define AB8500_GPIO_PUD2_REG 0x31 +#define AB8500_GPIO_PUD3_REG 0x32 +#define AB8500_GPIO_PUD4_REG 0x33 +#define AB8500_GPIO_PUD5_REG 0x34 +#define AB8500_GPIO_PUD6_REG 0x35 +#define AB9540_GPIO_PUD7_REG 0x36 + +#define AB8500_GPIO_IN1_REG 0x40 +#define AB8500_GPIO_IN2_REG 0x41 +#define AB8500_GPIO_IN3_REG 0x42 +#define AB8500_GPIO_IN4_REG 0x43 +#define AB8500_GPIO_IN5_REG 0x44 +#define AB8500_GPIO_IN6_REG 0x45 +#define AB9540_GPIO_IN7_REG 0x46 +#define AB8540_GPIO_VINSEL_REG 0x47 +#define AB8540_GPIO_PULL_UPDOWN_REG 0x48 +#define AB8500_GPIO_ALTFUN_REG 0x50 +#define AB8500_NUM_VIR_GPIO_IRQ 16 +#define AB8540_GPIO_PULL_UPDOWN_MASK 0x03 +#define AB8540_GPIO_VINSEL_MASK 0x03 +#define AB8540_GPIOX_VBAT_START 51 +#define AB8540_GPIOX_VBAT_END 54 + +enum abx500_gpio_action { + NONE, + STARTUP, + SHUTDOWN, + MASK, + UNMASK +}; + +struct abx500_pinctrl { + struct device *dev; + struct pinctrl_dev *pctldev; + struct abx500_pinctrl_soc_data *soc; + struct gpio_chip chip; + struct ab8500 *parent; + struct mutex lock; + u32 irq_base; + enum abx500_gpio_action irq_action; + u16 rising; + u16 falling; + struct abx500_gpio_irq_cluster *irq_cluster; + int irq_cluster_size; + int irq_gpio_rising_offset; + int irq_gpio_falling_offset; + int irq_gpio_factor; +}; + +/** + * to_abx500_pinctrl() - get the pointer to abx500_pinctrl + * @chip: Member of the structure abx500_pinctrl + */ +static inline struct abx500_pinctrl *to_abx500_pinctrl(struct gpio_chip *chip) +{ + return container_of(chip, struct abx500_pinctrl, chip); +} + +static int abx500_gpio_get_bit(struct gpio_chip *chip, u8 reg, + unsigned offset, bool *bit) +{ + struct abx500_pinctrl *pct = to_abx500_pinctrl(chip); + u8 pos = offset % 8; + u8 val; + int ret; + + reg += offset / 8; + ret = abx500_get_register_interruptible(pct->dev, + AB8500_MISC, reg, &val); + + *bit = !!(val & BIT(pos)); + + if (ret < 0) + dev_err(pct->dev, + "%s read reg =%x, offset=%x failed\n", + __func__, reg, offset); + + return ret; +} + +static int abx500_gpio_set_bits(struct gpio_chip *chip, u8 reg, + unsigned offset, int val) +{ + struct abx500_pinctrl *pct = to_abx500_pinctrl(chip); + u8 pos = offset % 8; + int ret; + + reg += offset / 8; + ret = abx500_mask_and_set_register_interruptible(pct->dev, + AB8500_MISC, reg, 1 << pos, val << pos); + if (ret < 0) + dev_err(pct->dev, "%s write failed\n", __func__); + return ret; +} +/** + * abx500_gpio_get() - Get the particular GPIO value + * @chip: Gpio device + * @offset: GPIO number to read + */ +static int abx500_gpio_get(struct gpio_chip *chip, unsigned offset) +{ + struct abx500_pinctrl *pct = to_abx500_pinctrl(chip); + bool bit; + int ret; + + ret = abx500_gpio_get_bit(chip, AB8500_GPIO_IN1_REG, + offset, &bit); + if (ret < 0) { + dev_err(pct->dev, "%s failed\n", __func__); + return ret; + } + return bit; +} + +static void abx500_gpio_set(struct gpio_chip *chip, unsigned offset, int val) +{ + struct abx500_pinctrl *pct = to_abx500_pinctrl(chip); + int ret; + + ret = abx500_gpio_set_bits(chip, AB8500_GPIO_OUT1_REG, offset, val); + if (ret < 0) + dev_err(pct->dev, "%s write failed\n", __func__); +} + +static int abx500_config_pull_updown(struct abx500_pinctrl *pct, + int offset, enum abx500_gpio_pull_updown val) +{ + u8 pos; + int ret; + struct pullud *pullud; + + if (!pct->soc->pullud) { + dev_err(pct->dev, "%s AB chip doesn't support pull up/down feature", + __func__); + ret = -EPERM; + goto out; + } + + pullud = pct->soc->pullud; + + if ((offset < pullud->first_pin) + || (offset > pullud->last_pin)) { + ret = -EINVAL; + goto out; + } + + pos = offset << 1; + + ret = abx500_mask_and_set_register_interruptible(pct->dev, + AB8500_MISC, AB8540_GPIO_PULL_UPDOWN_REG, + AB8540_GPIO_PULL_UPDOWN_MASK << pos, val << pos); + +out: + if (ret < 0) + dev_err(pct->dev, "%s failed (%d)\n", __func__, ret); + return ret; +} + +static int abx500_gpio_direction_output(struct gpio_chip *chip, + unsigned offset, + int val) +{ + struct abx500_pinctrl *pct = to_abx500_pinctrl(chip); + struct pullud *pullud = pct->soc->pullud; + unsigned gpio; + int ret; + /* set direction as output */ + ret = abx500_gpio_set_bits(chip, AB8500_GPIO_DIR1_REG, offset, 1); + if (ret < 0) + return ret; + + /* disable pull down */ + ret = abx500_gpio_set_bits(chip, AB8500_GPIO_PUD1_REG, offset, 1); + if (ret < 0) + return ret; + + /* if supported, disable both pull down and pull up */ + gpio = offset + 1; + if (pullud && gpio >= pullud->first_pin && gpio <= pullud->last_pin) { + ret = abx500_config_pull_updown(pct, + gpio, + ABX500_GPIO_PULL_NONE); + if (ret < 0) + return ret; + } + /* set the output as 1 or 0 */ + return abx500_gpio_set_bits(chip, AB8500_GPIO_OUT1_REG, offset, val); +} + +static int abx500_gpio_direction_input(struct gpio_chip *chip, unsigned offset) +{ + /* set the register as input */ + return abx500_gpio_set_bits(chip, AB8500_GPIO_DIR1_REG, offset, 0); +} + +static int abx500_gpio_to_irq(struct gpio_chip *chip, unsigned offset) +{ + struct abx500_pinctrl *pct = to_abx500_pinctrl(chip); + int base = pct->irq_base; + int i; + + for (i = 0; i < pct->irq_cluster_size; i++) { + struct abx500_gpio_irq_cluster *cluster = + &pct->irq_cluster[i]; + + if (offset >= cluster->start && offset <= cluster->end) + return base + offset - cluster->start; + + /* Advance by the number of gpios in this cluster */ + base += cluster->end + cluster->offset - cluster->start + 1; + } + + return -EINVAL; +} + +static int abx500_set_mode(struct pinctrl_dev *pctldev, struct gpio_chip *chip, + unsigned gpio, int alt_setting) +{ + struct abx500_pinctrl *pct = pinctrl_dev_get_drvdata(pctldev); + struct alternate_functions af = pct->soc->alternate_functions[gpio]; + int ret; + int val; + unsigned offset; + const char *modes[] = { + [ABX500_DEFAULT] = "default", + [ABX500_ALT_A] = "altA", + [ABX500_ALT_B] = "altB", + [ABX500_ALT_C] = "altC", + }; + + /* sanity check */ + if (((alt_setting == ABX500_ALT_A) && (af.gpiosel_bit == UNUSED)) || + ((alt_setting == ABX500_ALT_B) && (af.alt_bit1 == UNUSED)) || + ((alt_setting == ABX500_ALT_C) && (af.alt_bit2 == UNUSED))) { + dev_dbg(pct->dev, "pin %d doesn't support %s mode\n", gpio, + modes[alt_setting]); + return -EINVAL; + } + + /* on ABx5xx, there is no GPIO0, so adjust the offset */ + offset = gpio - 1; + switch (alt_setting) { + case ABX500_DEFAULT: + /* + * for ABx5xx family, default mode is always selected by + * writing 0 to GPIOSELx register, except for pins which + * support at least ALT_B mode, default mode is selected + * by writing 1 to GPIOSELx register + */ + val = 0; + if (af.alt_bit1 != UNUSED) + val++; + + ret = abx500_gpio_set_bits(chip, AB8500_GPIO_SEL1_REG, + offset, val); + break; + case ABX500_ALT_A: + /* + * for ABx5xx family, alt_a mode is always selected by + * writing 1 to GPIOSELx register, except for pins which + * support at least ALT_B mode, alt_a mode is selected + * by writing 0 to GPIOSELx register and 0 in ALTFUNC + * register + */ + if (af.alt_bit1 != UNUSED) { + ret = abx500_gpio_set_bits(chip, AB8500_GPIO_SEL1_REG, + offset, 0); + ret = abx500_gpio_set_bits(chip, + AB8500_GPIO_ALTFUN_REG, + af.alt_bit1, + !!(af.alta_val && BIT(0))); + if (af.alt_bit2 != UNUSED) + ret = abx500_gpio_set_bits(chip, + AB8500_GPIO_ALTFUN_REG, + af.alt_bit2, + !!(af.alta_val && BIT(1))); + } else + ret = abx500_gpio_set_bits(chip, AB8500_GPIO_SEL1_REG, + offset, 1); + break; + case ABX500_ALT_B: + ret = abx500_gpio_set_bits(chip, AB8500_GPIO_SEL1_REG, + offset, 0); + ret = abx500_gpio_set_bits(chip, AB8500_GPIO_ALTFUN_REG, + af.alt_bit1, !!(af.altb_val && BIT(0))); + if (af.alt_bit2 != UNUSED) + ret = abx500_gpio_set_bits(chip, + AB8500_GPIO_ALTFUN_REG, + af.alt_bit2, + !!(af.altb_val && BIT(1))); + break; + case ABX500_ALT_C: + ret = abx500_gpio_set_bits(chip, AB8500_GPIO_SEL1_REG, + offset, 0); + ret = abx500_gpio_set_bits(chip, AB8500_GPIO_ALTFUN_REG, + af.alt_bit2, !!(af.altc_val && BIT(0))); + ret = abx500_gpio_set_bits(chip, AB8500_GPIO_ALTFUN_REG, + af.alt_bit2, !!(af.altc_val && BIT(1))); + break; + + default: + dev_dbg(pct->dev, "unknow alt_setting %d\n", alt_setting); + return -EINVAL; + } + return ret; +} + +static u8 abx500_get_mode(struct pinctrl_dev *pctldev, struct gpio_chip *chip, + unsigned gpio) +{ + u8 mode; + bool bit_mode; + bool alt_bit1; + bool alt_bit2; + struct abx500_pinctrl *pct = pinctrl_dev_get_drvdata(pctldev); + struct alternate_functions af = pct->soc->alternate_functions[gpio]; + + /* + * if gpiosel_bit is set to unused, + * it means no GPIO or special case + */ + if (af.gpiosel_bit == UNUSED) + return ABX500_DEFAULT; + + /* read GpioSelx register */ + abx500_gpio_get_bit(chip, AB8500_GPIO_SEL1_REG + (gpio / 8), + af.gpiosel_bit, &bit_mode); + mode = bit_mode; + + /* sanity check */ + if ((af.alt_bit1 < UNUSED) || (af.alt_bit1 > 7) || + (af.alt_bit2 < UNUSED) || (af.alt_bit2 > 7)) { + dev_err(pct->dev, + "alt_bitX value not in correct range (-1 to 7)\n"); + return -EINVAL; + } + /* if alt_bit2 is used, alt_bit1 must be used too */ + if ((af.alt_bit2 != UNUSED) && (af.alt_bit1 == UNUSED)) { + dev_err(pct->dev, + "if alt_bit2 is used, alt_bit1 can't be unused\n"); + return -EINVAL; + } + + /* check if pin use AlternateFunction register */ + if ((af.alt_bit1 == UNUSED) && (af.alt_bit1 == UNUSED)) + return mode; + /* + * if pin GPIOSEL bit is set and pin supports alternate function, + * it means DEFAULT mode + */ + if (mode) + return ABX500_DEFAULT; + /* + * pin use the AlternatFunction register + * read alt_bit1 value + */ + abx500_gpio_get_bit(chip, AB8500_GPIO_ALTFUN_REG, + af.alt_bit1, &alt_bit1); + + if (af.alt_bit2 != UNUSED) + /* read alt_bit2 value */ + abx500_gpio_get_bit(chip, AB8500_GPIO_ALTFUN_REG, af.alt_bit2, + &alt_bit2); + else + alt_bit2 = 0; + + mode = (alt_bit2 << 1) + alt_bit1; + if (mode == af.alta_val) + return ABX500_ALT_A; + else if (mode == af.altb_val) + return ABX500_ALT_B; + else + return ABX500_ALT_C; +} + +#ifdef CONFIG_DEBUG_FS + +#include + +static void abx500_gpio_dbg_show_one(struct seq_file *s, + struct pinctrl_dev *pctldev, struct gpio_chip *chip, + unsigned offset, unsigned gpio) +{ + struct abx500_pinctrl *pct = to_abx500_pinctrl(chip); + const char *label = gpiochip_is_requested(chip, offset - 1); + u8 gpio_offset = offset - 1; + int mode = -1; + bool is_out; + bool pull; + const char *modes[] = { + [ABX500_DEFAULT] = "default", + [ABX500_ALT_A] = "altA", + [ABX500_ALT_B] = "altB", + [ABX500_ALT_C] = "altC", + }; + + abx500_gpio_get_bit(chip, AB8500_GPIO_DIR1_REG, gpio_offset, &is_out); + abx500_gpio_get_bit(chip, AB8500_GPIO_PUD1_REG, gpio_offset, &pull); + + if (pctldev) + mode = abx500_get_mode(pctldev, chip, offset); + + seq_printf(s, " gpio-%-3d (%-20.20s) %-3s %-9s %s", + gpio, label ?: "(none)", + is_out ? "out" : "in ", + is_out ? + (chip->get + ? (chip->get(chip, offset) ? "hi" : "lo") + : "? ") + : (pull ? "pull up" : "pull down"), + (mode < 0) ? "unknown" : modes[mode]); + + if (label && !is_out) { + int irq = gpio_to_irq(gpio); + struct irq_desc *desc = irq_to_desc(irq); + + if (irq >= 0 && desc->action) { + char *trigger; + int irq_offset = irq - pct->irq_base; + + if (pct->rising & BIT(irq_offset)) + trigger = "edge-rising"; + else if (pct->falling & BIT(irq_offset)) + trigger = "edge-falling"; + else + trigger = "edge-undefined"; + + seq_printf(s, " irq-%d %s", irq, trigger); + } + } +} + +static void abx500_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip) +{ + unsigned i; + unsigned gpio = chip->base; + struct abx500_pinctrl *pct = to_abx500_pinctrl(chip); + struct pinctrl_dev *pctldev = pct->pctldev; + + for (i = 0; i < chip->ngpio; i++, gpio++) { + /* On AB8500, there is no GPIO0, the first is the GPIO 1 */ + abx500_gpio_dbg_show_one(s, pctldev, chip, i + 1, gpio); + seq_printf(s, "\n"); + } +} + +#else +static inline void abx500_gpio_dbg_show_one(struct seq_file *s, + struct pinctrl_dev *pctldev, + struct gpio_chip *chip, + unsigned offset, unsigned gpio) +{ +} +#define abx500_gpio_dbg_show NULL +#endif + +int abx500_gpio_request(struct gpio_chip *chip, unsigned offset) +{ + int gpio = chip->base + offset; + + return pinctrl_request_gpio(gpio); +} + +void abx500_gpio_free(struct gpio_chip *chip, unsigned offset) +{ + int gpio = chip->base + offset; + + pinctrl_free_gpio(gpio); +} + +static struct gpio_chip abx500gpio_chip = { + .label = "abx500-gpio", + .owner = THIS_MODULE, + .request = abx500_gpio_request, + .free = abx500_gpio_free, + .direction_input = abx500_gpio_direction_input, + .get = abx500_gpio_get, + .direction_output = abx500_gpio_direction_output, + .set = abx500_gpio_set, + .to_irq = abx500_gpio_to_irq, + .dbg_show = abx500_gpio_dbg_show, +}; + +static unsigned int irq_to_rising(unsigned int irq) +{ + struct abx500_pinctrl *pct = irq_get_chip_data(irq); + int offset = irq - pct->irq_base; + int new_irq; + + new_irq = offset * pct->irq_gpio_factor + + pct->irq_gpio_rising_offset + + pct->parent->irq_base; + + return new_irq; +} + +static unsigned int irq_to_falling(unsigned int irq) +{ + struct abx500_pinctrl *pct = irq_get_chip_data(irq); + int offset = irq - pct->irq_base; + int new_irq; + + new_irq = offset * pct->irq_gpio_factor + + pct->irq_gpio_falling_offset + + pct->parent->irq_base; + return new_irq; + +} + +static unsigned int rising_to_irq(unsigned int irq, void *dev) +{ + struct abx500_pinctrl *pct = dev; + int offset, new_irq; + + offset = irq - pct->irq_gpio_rising_offset + - pct->parent->irq_base; + new_irq = (offset / pct->irq_gpio_factor) + + pct->irq_base; + + return new_irq; +} + +static unsigned int falling_to_irq(unsigned int irq, void *dev) +{ + struct abx500_pinctrl *pct = dev; + int offset, new_irq; + + offset = irq - pct->irq_gpio_falling_offset + - pct->parent->irq_base; + new_irq = (offset / pct->irq_gpio_factor) + + pct->irq_base; + + return new_irq; +} + +/* + * IRQ handler + */ + +static irqreturn_t handle_rising(int irq, void *dev) +{ + + handle_nested_irq(rising_to_irq(irq , dev)); + return IRQ_HANDLED; +} + +static irqreturn_t handle_falling(int irq, void *dev) +{ + + handle_nested_irq(falling_to_irq(irq, dev)); + return IRQ_HANDLED; +} + +static void abx500_gpio_irq_lock(struct irq_data *data) +{ + struct abx500_pinctrl *pct = irq_data_get_irq_chip_data(data); + mutex_lock(&pct->lock); +} + +static void abx500_gpio_irq_sync_unlock(struct irq_data *data) +{ + struct abx500_pinctrl *pct = irq_data_get_irq_chip_data(data); + unsigned int irq = data->irq; + int offset = irq - pct->irq_base; + bool rising = pct->rising & BIT(offset); + bool falling = pct->falling & BIT(offset); + int ret; + + switch (pct->irq_action) { + case STARTUP: + if (rising) + ret = request_threaded_irq(irq_to_rising(irq), + NULL, handle_rising, + IRQF_TRIGGER_RISING | IRQF_NO_SUSPEND, + "abx500-gpio-r", pct); + if (falling) + ret = request_threaded_irq(irq_to_falling(irq), + NULL, handle_falling, + IRQF_TRIGGER_FALLING | IRQF_NO_SUSPEND, + "abx500-gpio-f", pct); + break; + case SHUTDOWN: + if (rising) + free_irq(irq_to_rising(irq), pct); + if (falling) + free_irq(irq_to_falling(irq), pct); + break; + case MASK: + if (rising) + disable_irq(irq_to_rising(irq)); + if (falling) + disable_irq(irq_to_falling(irq)); + break; + case UNMASK: + if (rising) + enable_irq(irq_to_rising(irq)); + if (falling) + enable_irq(irq_to_falling(irq)); + break; + case NONE: + break; + } + pct->irq_action = NONE; + pct->rising &= ~(BIT(offset)); + pct->falling &= ~(BIT(offset)); + mutex_unlock(&pct->lock); +} + + +static void abx500_gpio_irq_mask(struct irq_data *data) +{ + struct abx500_pinctrl *pct = irq_data_get_irq_chip_data(data); + pct->irq_action = MASK; +} + +static void abx500_gpio_irq_unmask(struct irq_data *data) +{ + struct abx500_pinctrl *pct = irq_data_get_irq_chip_data(data); + pct->irq_action = UNMASK; +} + +static int abx500_gpio_irq_set_type(struct irq_data *data, unsigned int type) +{ + struct abx500_pinctrl *pct = irq_data_get_irq_chip_data(data); + unsigned int irq = data->irq; + int offset = irq - pct->irq_base; + + if (type == IRQ_TYPE_EDGE_BOTH) { + pct->rising = BIT(offset); + pct->falling = BIT(offset); + } else if (type == IRQ_TYPE_EDGE_RISING) { + pct->rising = BIT(offset); + } else { + pct->falling = BIT(offset); + } + return 0; +} + +static unsigned int abx500_gpio_irq_startup(struct irq_data *data) +{ + struct abx500_pinctrl *pct = irq_data_get_irq_chip_data(data); + pct->irq_action = STARTUP; + return 0; +} + +static void abx500_gpio_irq_shutdown(struct irq_data *data) +{ + struct abx500_pinctrl *pct = irq_data_get_irq_chip_data(data); + pct->irq_action = SHUTDOWN; +} + +static struct irq_chip abx500_gpio_irq_chip = { + .name = "abx500-gpio", + .irq_startup = abx500_gpio_irq_startup, + .irq_shutdown = abx500_gpio_irq_shutdown, + .irq_bus_lock = abx500_gpio_irq_lock, + .irq_bus_sync_unlock = abx500_gpio_irq_sync_unlock, + .irq_mask = abx500_gpio_irq_mask, + .irq_unmask = abx500_gpio_irq_unmask, + .irq_set_type = abx500_gpio_irq_set_type, +}; + +static int abx500_gpio_irq_init(struct abx500_pinctrl *pct) +{ + u32 base = pct->irq_base; + int irq; + + for (irq = base; irq < base + AB8500_NUM_VIR_GPIO_IRQ ; irq++) { + irq_set_chip_data(irq, pct); + irq_set_chip_and_handler(irq, &abx500_gpio_irq_chip, + handle_simple_irq); + irq_set_nested_thread(irq, 1); +#ifdef CONFIG_ARM + set_irq_flags(irq, IRQF_VALID); +#else + irq_set_noprobe(irq); +#endif + } + + return 0; +} + +static void abx500_gpio_irq_remove(struct abx500_pinctrl *pct) +{ + int base = pct->irq_base; + int irq; + + for (irq = base; irq < base + AB8500_NUM_VIR_GPIO_IRQ; irq++) { +#ifdef CONFIG_ARM + set_irq_flags(irq, 0); +#endif + irq_set_chip_and_handler(irq, NULL, NULL); + irq_set_chip_data(irq, NULL); + } +} + +static int abx500_pmx_get_funcs_cnt(struct pinctrl_dev *pctldev) +{ + struct abx500_pinctrl *pct = pinctrl_dev_get_drvdata(pctldev); + + return pct->soc->nfunctions; +} + +static const char *abx500_pmx_get_func_name(struct pinctrl_dev *pctldev, + unsigned function) +{ + struct abx500_pinctrl *pct = pinctrl_dev_get_drvdata(pctldev); + + return pct->soc->functions[function].name; +} + +static int abx500_pmx_get_func_groups(struct pinctrl_dev *pctldev, + unsigned function, + const char * const **groups, + unsigned * const num_groups) +{ + struct abx500_pinctrl *pct = pinctrl_dev_get_drvdata(pctldev); + + *groups = pct->soc->functions[function].groups; + *num_groups = pct->soc->functions[function].ngroups; + + return 0; +} + +static void abx500_disable_lazy_irq(struct gpio_chip *chip, unsigned gpio) +{ + struct abx500_pinctrl *pct = to_abx500_pinctrl(chip); + int irq; + int offset; + bool rising; + bool falling; + + /* + * check if gpio has interrupt capability and convert + * gpio number to irq + * On ABx5xx, there is no GPIO0, GPIO1 is the + * first one, so adjust gpio number + */ + gpio--; + irq = gpio_to_irq(gpio + chip->base); + if (irq < 0) + return; + + offset = irq - pct->irq_base; + rising = pct->rising & BIT(offset); + falling = pct->falling & BIT(offset); + + /* nothing to do ?*/ + if (!rising && !falling) + return; + + if (rising) { + disable_irq(irq_to_rising(irq)); + free_irq(irq_to_rising(irq), pct); + } + if (falling) { + disable_irq(irq_to_falling(irq)); + free_irq(irq_to_falling(irq), pct); + } +} + +static int abx500_pmx_enable(struct pinctrl_dev *pctldev, unsigned function, + unsigned group) +{ + struct abx500_pinctrl *pct = pinctrl_dev_get_drvdata(pctldev); + struct gpio_chip *chip = &pct->chip; + const struct abx500_pingroup *g; + int i; + int ret = 0; + + g = &pct->soc->groups[group]; + if (g->altsetting < 0) + return -EINVAL; + + dev_dbg(pct->dev, "enable group %s, %u pins\n", g->name, g->npins); + + for (i = 0; i < g->npins; i++) { + dev_dbg(pct->dev, "setting pin %d to altsetting %d\n", + g->pins[i], g->altsetting); + + abx500_disable_lazy_irq(chip, g->pins[i]); + ret = abx500_set_mode(pctldev, chip, g->pins[i], g->altsetting); + } + return ret; +} + +static void abx500_pmx_disable(struct pinctrl_dev *pctldev, + unsigned function, unsigned group) +{ + struct abx500_pinctrl *pct = pinctrl_dev_get_drvdata(pctldev); + const struct abx500_pingroup *g; + + g = &pct->soc->groups[group]; + if (g->altsetting < 0) + return; + + /* FIXME: poke out the mux, set the pin to some default state? */ + dev_dbg(pct->dev, "disable group %s, %u pins\n", g->name, g->npins); +} + +int abx500_gpio_request_enable(struct pinctrl_dev *pctldev, + struct pinctrl_gpio_range *range, + unsigned offset) +{ + struct abx500_pinctrl *pct = pinctrl_dev_get_drvdata(pctldev); + const struct abx500_pinrange *p; + int ret; + int i; + + /* + * Different ranges have different ways to enable GPIO function on a + * pin, so refer back to our local range type, where we handily define + * what altfunc enables GPIO for a certain pin. + */ + for (i = 0; i < pct->soc->gpio_num_ranges; i++) { + p = &pct->soc->gpio_ranges[i]; + if ((offset >= p->offset) && + (offset < (p->offset + p->npins))) + break; + } + + if (i == pct->soc->gpio_num_ranges) { + dev_err(pct->dev, "%s failed to locate range\n", __func__); + return -ENODEV; + } + + dev_dbg(pct->dev, "enable GPIO by altfunc %d at gpio %d\n", + p->altfunc, offset); + + ret = abx500_set_mode(pct->pctldev, &pct->chip, + offset, p->altfunc); + if (ret < 0) { + dev_err(pct->dev, "%s setting altfunc failed\n", __func__); + return ret; + } + + return ret; +} + +static void abx500_gpio_disable_free(struct pinctrl_dev *pctldev, + struct pinctrl_gpio_range *range, + unsigned offset) +{ +} + +static struct pinmux_ops abx500_pinmux_ops = { + .get_functions_count = abx500_pmx_get_funcs_cnt, + .get_function_name = abx500_pmx_get_func_name, + .get_function_groups = abx500_pmx_get_func_groups, + .enable = abx500_pmx_enable, + .disable = abx500_pmx_disable, + .gpio_request_enable = abx500_gpio_request_enable, + .gpio_disable_free = abx500_gpio_disable_free, +}; + +static int abx500_get_groups_cnt(struct pinctrl_dev *pctldev) +{ + struct abx500_pinctrl *pct = pinctrl_dev_get_drvdata(pctldev); + + return pct->soc->ngroups; +} + +static const char *abx500_get_group_name(struct pinctrl_dev *pctldev, + unsigned selector) +{ + struct abx500_pinctrl *pct = pinctrl_dev_get_drvdata(pctldev); + + return pct->soc->groups[selector].name; +} + +static int abx500_get_group_pins(struct pinctrl_dev *pctldev, + unsigned selector, + const unsigned **pins, + unsigned *num_pins) +{ + struct abx500_pinctrl *pct = pinctrl_dev_get_drvdata(pctldev); + + *pins = pct->soc->groups[selector].pins; + *num_pins = pct->soc->groups[selector].npins; + return 0; +} + +static void abx500_pin_dbg_show(struct pinctrl_dev *pctldev, + struct seq_file *s, unsigned offset) +{ + struct abx500_pinctrl *pct = pinctrl_dev_get_drvdata(pctldev); + struct gpio_chip *chip = &pct->chip; + + abx500_gpio_dbg_show_one(s, pctldev, chip, offset, + chip->base + offset - 1); +} + +static struct pinctrl_ops abx500_pinctrl_ops = { + .get_groups_count = abx500_get_groups_cnt, + .get_group_name = abx500_get_group_name, + .get_group_pins = abx500_get_group_pins, + .pin_dbg_show = abx500_pin_dbg_show, +}; + +int abx500_pin_config_get(struct pinctrl_dev *pctldev, + unsigned pin, + unsigned long *config) +{ + /* Not implemented */ + return -EINVAL; +} + +int abx500_pin_config_set(struct pinctrl_dev *pctldev, + unsigned pin, + unsigned long config) +{ + struct abx500_pinctrl *pct = pinctrl_dev_get_drvdata(pctldev); + struct pullud *pullud = pct->soc->pullud; + struct gpio_chip *chip = &pct->chip; + unsigned offset; + int ret; + enum pin_config_param param = pinconf_to_config_param(config); + enum pin_config_param argument = pinconf_to_config_argument(config); + + dev_dbg(chip->dev, "pin %d [%#lx]: %s %s\n", + pin, config, (param == PIN_CONFIG_OUTPUT) ? "output " : "input", + (param == PIN_CONFIG_OUTPUT) ? (argument ? "high" : "low") : + (argument ? "pull up" : "pull down")); + /* on ABx500, there is no GPIO0, so adjust the offset */ + offset = pin - 1; + + switch (param) { + case PIN_CONFIG_BIAS_PULL_DOWN: + /* + * if argument = 1 set the pull down + * else clear the pull down + */ + ret = abx500_gpio_direction_input(chip, offset); + /* + * Some chips only support pull down, while some actually + * support both pull up and pull down. Such chips have + * a "pullud" range specified for the pins that support + * both features. If the pin is not within that range, we + * fall back to the old bit set that only support pull down. + */ + if (pullud && + pin >= pullud->first_pin && + pin <= pullud->last_pin) + ret = abx500_config_pull_updown(pct, + pin, + argument ? ABX500_GPIO_PULL_DOWN : ABX500_GPIO_PULL_NONE); + else + /* Chip only supports pull down */ + ret = abx500_gpio_set_bits(chip, AB8500_GPIO_PUD1_REG, + offset, argument ? 0 : 1); + break; + case PIN_CONFIG_OUTPUT: + ret = abx500_gpio_direction_output(chip, offset, argument); + break; + default: + dev_err(chip->dev, "illegal configuration requested\n"); + return -EINVAL; + } + return ret; +} + +static struct pinconf_ops abx500_pinconf_ops = { + .pin_config_get = abx500_pin_config_get, + .pin_config_set = abx500_pin_config_set, +}; + +static struct pinctrl_desc abx500_pinctrl_desc = { + .name = "pinctrl-abx500", + .pctlops = &abx500_pinctrl_ops, + .pmxops = &abx500_pinmux_ops, + .confops = &abx500_pinconf_ops, + .owner = THIS_MODULE, +}; + +static int abx500_get_gpio_num(struct abx500_pinctrl_soc_data *soc) +{ + unsigned int lowest = 0; + unsigned int highest = 0; + unsigned int npins = 0; + int i; + + /* + * Compute number of GPIOs from the last SoC gpio range descriptors + * These ranges may include "holes" but the GPIO number space shall + * still be homogeneous, so we need to detect and account for any + * such holes so that these are included in the number of GPIO pins. + */ + for (i = 0; i < soc->gpio_num_ranges; i++) { + unsigned gstart; + unsigned gend; + const struct abx500_pinrange *p; + + p = &soc->gpio_ranges[i]; + gstart = p->offset; + gend = p->offset + p->npins - 1; + + if (i == 0) { + /* First iteration, set start values */ + lowest = gstart; + highest = gend; + } else { + if (gstart < lowest) + lowest = gstart; + if (gend > highest) + highest = gend; + } + } + /* this gives the absolute number of pins */ + npins = highest - lowest + 1; + return npins; +} + +static int abx500_gpio_probe(struct platform_device *pdev) +{ + struct ab8500_platform_data *abx500_pdata = + dev_get_platdata(pdev->dev.parent); + struct abx500_gpio_platform_data *pdata; + struct abx500_pinctrl *pct; + const struct platform_device_id *platid = platform_get_device_id(pdev); + int ret; + int i; + + pdata = abx500_pdata->gpio; + if (!pdata) { + dev_err(&pdev->dev, "gpio platform data missing\n"); + return -ENODEV; + } + + pct = devm_kzalloc(&pdev->dev, sizeof(struct abx500_pinctrl), + GFP_KERNEL); + if (pct == NULL) { + dev_err(&pdev->dev, + "failed to allocate memory for pct\n"); + return -ENOMEM; + } + + pct->dev = &pdev->dev; + pct->parent = dev_get_drvdata(pdev->dev.parent); + pct->chip = abx500gpio_chip; + pct->chip.dev = &pdev->dev; + pct->chip.base = pdata->gpio_base; + pct->irq_base = pdata->irq_base; + + /* initialize the lock */ + mutex_init(&pct->lock); + + /* Poke in other ASIC variants here */ + switch (platid->driver_data) { + default: + dev_err(&pdev->dev, "Unsupported pinctrl sub driver (%d)\n", + (int) platid->driver_data); + return -EINVAL; + } + + if (!pct->soc) { + dev_err(&pdev->dev, "Invalid SOC data\n"); + return -EINVAL; + } + + pct->chip.ngpio = abx500_get_gpio_num(pct->soc); + pct->irq_cluster = pct->soc->gpio_irq_cluster; + pct->irq_cluster_size = pct->soc->ngpio_irq_cluster; + pct->irq_gpio_rising_offset = pct->soc->irq_gpio_rising_offset; + pct->irq_gpio_falling_offset = pct->soc->irq_gpio_falling_offset; + pct->irq_gpio_factor = pct->soc->irq_gpio_factor; + + ret = abx500_gpio_irq_init(pct); + if (ret) + goto out_free; + ret = gpiochip_add(&pct->chip); + if (ret) { + dev_err(&pdev->dev, "unable to add gpiochip: %d\n", + ret); + goto out_rem_irq; + } + dev_info(&pdev->dev, "added gpiochip\n"); + + abx500_pinctrl_desc.pins = pct->soc->pins; + abx500_pinctrl_desc.npins = pct->soc->npins; + pct->pctldev = pinctrl_register(&abx500_pinctrl_desc, &pdev->dev, pct); + if (!pct->pctldev) { + dev_err(&pdev->dev, + "could not register abx500 pinctrl driver\n"); + goto out_rem_chip; + } + dev_info(&pdev->dev, "registered pin controller\n"); + + /* We will handle a range of GPIO pins */ + for (i = 0; i < pct->soc->gpio_num_ranges; i++) { + const struct abx500_pinrange *p = &pct->soc->gpio_ranges[i]; + + ret = gpiochip_add_pin_range(&pct->chip, + dev_name(&pdev->dev), + p->offset - 1, p->offset, p->npins); + if (ret < 0) + return ret; + } + + platform_set_drvdata(pdev, pct); + dev_info(&pdev->dev, "initialized abx500 pinctrl driver\n"); + + return 0; + +out_rem_chip: + ret = gpiochip_remove(&pct->chip); + if (ret) + dev_info(&pdev->dev, "failed to remove gpiochip\n"); +out_rem_irq: + abx500_gpio_irq_remove(pct); +out_free: + mutex_destroy(&pct->lock); + return ret; +} + +/* + * abx500_gpio_remove() - remove Ab8500-gpio driver + * @pdev : Platform device registered + */ +static int abx500_gpio_remove(struct platform_device *pdev) +{ + struct abx500_pinctrl *pct = platform_get_drvdata(pdev); + int ret; + + ret = gpiochip_remove(&pct->chip); + if (ret < 0) { + dev_err(pct->dev, "unable to remove gpiochip: %d\n", + ret); + return ret; + } + + mutex_destroy(&pct->lock); + + return 0; +} + +static const struct platform_device_id abx500_pinctrl_id[] = { + { "pinctrl-ab8500", PINCTRL_AB8500 }, + { "pinctrl-ab8540", PINCTRL_AB8540 }, + { "pinctrl-ab9540", PINCTRL_AB9540 }, + { "pinctrl-ab8505", PINCTRL_AB8505 }, + { }, +}; + +static struct platform_driver abx500_gpio_driver = { + .driver = { + .name = "abx500-gpio", + .owner = THIS_MODULE, + }, + .probe = abx500_gpio_probe, + .remove = abx500_gpio_remove, + .id_table = abx500_pinctrl_id, +}; + +static int __init abx500_gpio_init(void) +{ + return platform_driver_register(&abx500_gpio_driver); +} +core_initcall(abx500_gpio_init); + +MODULE_AUTHOR("Patrice Chotard "); +MODULE_DESCRIPTION("Driver allows to use AxB5xx unused pins to be used as GPIO"); +MODULE_ALIAS("platform:abx500-gpio"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/pinctrl/pinctrl-abx500.h b/drivers/pinctrl/pinctrl-abx500.h new file mode 100644 index 000000000000..436ace356175 --- /dev/null +++ b/drivers/pinctrl/pinctrl-abx500.h @@ -0,0 +1,180 @@ +#ifndef PINCTRL_PINCTRL_ABx5O0_H +#define PINCTRL_PINCTRL_ABx500_H + +/* Package definitions */ +#define PINCTRL_AB8500 0 +#define PINCTRL_AB8540 1 +#define PINCTRL_AB9540 2 +#define PINCTRL_AB8505 3 + +/* pins alternate function */ +enum abx500_pin_func { + ABX500_DEFAULT, + ABX500_ALT_A, + ABX500_ALT_B, + ABX500_ALT_C, +}; + +/** + * struct abx500_function - ABx500 pinctrl mux function + * @name: The name of the function, exported to pinctrl core. + * @groups: An array of pin groups that may select this function. + * @ngroups: The number of entries in @groups. + */ +struct abx500_function { + const char *name; + const char * const *groups; + unsigned ngroups; +}; + +/** + * struct abx500_pingroup - describes a ABx500 pin group + * @name: the name of this specific pin group + * @pins: an array of discrete physical pins used in this group, taken + * from the driver-local pin enumeration space + * @num_pins: the number of pins in this group array, i.e. the number of + * elements in .pins so we can iterate over that array + * @altsetting: the altsetting to apply to all pins in this group to + * configure them to be used by a function + */ +struct abx500_pingroup { + const char *name; + const unsigned int *pins; + const unsigned npins; + int altsetting; +}; + +#define ALTERNATE_FUNCTIONS(pin, sel_bit, alt1, alt2, alta, altb, altc) \ +{ \ + .pin_number = pin, \ + .gpiosel_bit = sel_bit, \ + .alt_bit1 = alt1, \ + .alt_bit2 = alt2, \ + .alta_val = alta, \ + .altb_val = altb, \ + .altc_val = altc, \ +} + +#define UNUSED -1 +/** + * struct alternate_functions + * @pin_number: The pin number + * @gpiosel_bit: Control bit in GPIOSEL register, + * @alt_bit1: First AlternateFunction bit used to select the + * alternate function + * @alt_bit2: Second AlternateFunction bit used to select the + * alternate function + * + * these 3 following fields are necessary due to none + * coherency on how to select the altA, altB and altC + * function between the ABx500 SOC family when using + * alternatfunc register. + * @alta_val: value to write in alternatfunc to select altA function + * @altb_val: value to write in alternatfunc to select altB function + * @altc_val: value to write in alternatfunc to select altC function + */ +struct alternate_functions { + unsigned pin_number; + s8 gpiosel_bit; + s8 alt_bit1; + s8 alt_bit2; + u8 alta_val; + u8 altb_val; + u8 altc_val; +}; + +/** + * struct pullud - specific pull up/down feature + * @first_pin: The pin number of the first pins which support + * specific pull up/down + * @last_pin: The pin number of the last pins + */ +struct pullud { + unsigned first_pin; + unsigned last_pin; +}; + +#define GPIO_IRQ_CLUSTER(a, b, c) \ +{ \ + .start = a, \ + .end = b, \ + .offset = c, \ +} + +/** + * struct abx500_gpio_irq_cluster - indicates GPIOs which are interrupt + * capable + * @start: The pin number of the first pin interrupt capable + * @end: The pin number of the last pin interrupt capable + * @offset: offset used to compute specific setting strategy of + * the interrupt line + */ + +struct abx500_gpio_irq_cluster { + int start; + int end; + int offset; +}; + +/** + * struct abx500_pinrange - map pin numbers to GPIO offsets + * @offset: offset into the GPIO local numberspace, incidentally + * identical to the offset into the local pin numberspace + * @npins: number of pins to map from both offsets + * @altfunc: altfunc setting to be used to enable GPIO on a pin in + * this range (may vary) + */ +struct abx500_pinrange { + unsigned int offset; + unsigned int npins; + int altfunc; +}; + +#define ABX500_PINRANGE(a, b, c) { .offset = a, .npins = b, .altfunc = c } + +/** + * struct abx500_pinctrl_soc_data - ABx500 pin controller per-SoC configuration + * @gpio_ranges: An array of GPIO ranges for this SoC + * @gpio_num_ranges: The number of GPIO ranges for this SoC + * @pins: An array describing all pins the pin controller affects. + * All pins which are also GPIOs must be listed first within the + * array, and be numbered identically to the GPIO controller's + * numbering. + * @npins: The number of entries in @pins. + * @functions: The functions supported on this SoC. + * @nfunction: The number of entries in @functions. + * @groups: An array describing all pin groups the pin SoC supports. + * @ngroups: The number of entries in @groups. + * @alternate_functions: array describing pins which supports alternate and + * how to set it. + * @pullud: array describing pins which supports pull up/down + * specific registers. + * @gpio_irq_cluster: An array of GPIO interrupt capable for this SoC + * @ngpio_irq_cluster: The number of GPIO inetrrupt capable for this SoC + * @irq_gpio_rising_offset: Interrupt offset used as base to compute specific + * setting strategy of the rising interrupt line + * @irq_gpio_falling_offset: Interrupt offset used as base to compute specific + * setting strategy of the falling interrupt line + * @irq_gpio_factor: Factor used to compute specific setting strategy of + * the interrupt line + */ + +struct abx500_pinctrl_soc_data { + const struct abx500_pinrange *gpio_ranges; + unsigned gpio_num_ranges; + const struct pinctrl_pin_desc *pins; + unsigned npins; + const struct abx500_function *functions; + unsigned nfunctions; + const struct abx500_pingroup *groups; + unsigned ngroups; + struct alternate_functions *alternate_functions; + struct pullud *pullud; + struct abx500_gpio_irq_cluster *gpio_irq_cluster; + unsigned ngpio_irq_cluster; + int irq_gpio_rising_offset; + int irq_gpio_falling_offset; + int irq_gpio_factor; +}; + +#endif /* PINCTRL_PINCTRL_ABx500_H */ diff --git a/include/linux/mfd/abx500/ab8500-gpio.h b/include/linux/mfd/abx500/ab8500-gpio.h index 2387c207ea86..e8c8281e194a 100644 --- a/include/linux/mfd/abx500/ab8500-gpio.h +++ b/include/linux/mfd/abx500/ab8500-gpio.h @@ -14,10 +14,21 @@ * registers. */ -struct ab8500_gpio_platform_data { +struct abx500_gpio_platform_data { int gpio_base; u32 irq_base; - u8 config_reg[8]; +}; + +enum abx500_gpio_pull_updown { + ABX500_GPIO_PULL_DOWN = 0x0, + ABX500_GPIO_PULL_NONE = 0x1, + ABX500_GPIO_PULL_UP = 0x3, +}; + +enum abx500_gpio_vinsel { + ABX500_GPIO_VINSEL_VBAT = 0x0, + ABX500_GPIO_VINSEL_VIN_1V8 = 0x1, + ABX500_GPIO_VINSEL_VDD_BIF = 0x2, }; #endif /* _AB8500_GPIO_H */ diff --git a/include/linux/mfd/abx500/ab8500.h b/include/linux/mfd/abx500/ab8500.h index e640ea059be2..fc0534483c72 100644 --- a/include/linux/mfd/abx500/ab8500.h +++ b/include/linux/mfd/abx500/ab8500.h @@ -385,7 +385,7 @@ struct ab8500_platform_data { struct ab8500_regulator_reg_init *regulator_reg_init; int num_regulator; struct regulator_init_data *regulator; - struct ab8500_gpio_platform_data *gpio; + struct abx500_gpio_platform_data *gpio; struct ab8500_codec_platform_data *codec; };