From: Andy Gospodarek Date: Mon, 14 Dec 2009 10:48:58 +0000 (+0000) Subject: bonding: allow arp_ip_targets on separate vlans to use arp validation X-Git-Url: https://git.karo-electronics.de/?a=commitdiff_plain;h=1f3c8804acba841b5573b953f5560d2683d2db0d;p=linux-beck.git bonding: allow arp_ip_targets on separate vlans to use arp validation This allows a bond device to specify an arp_ip_target as a host that is not on the same vlan as the base bond device and still use arp validation. A configuration like this, now works: BONDING_OPTS="mode=active-backup arp_interval=1000 arp_ip_target=10.0.100.1 arp_validate=3" 1: lo: mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth1: mtu 1500 qdisc pfifo_fast master bond0 qlen 1000 link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff 3: eth0: mtu 1500 qdisc pfifo_fast master bond0 qlen 1000 link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff 8: bond0: mtu 1500 qdisc noqueue link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff inet6 fe80::213:21ff:febe:33e9/64 scope link valid_lft forever preferred_lft forever 9: bond0.100@bond0: mtu 1500 qdisc noqueue link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff inet 10.0.100.2/24 brd 10.0.100.255 scope global bond0.100 inet6 fe80::213:21ff:febe:33e9/64 scope link valid_lft forever preferred_lft forever Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009) Bonding Mode: fault-tolerance (active-backup) Primary Slave: None Currently Active Slave: eth1 MII Status: up MII Polling Interval (ms): 0 Up Delay (ms): 0 Down Delay (ms): 0 ARP Polling Interval (ms): 1000 ARP IP target/s (n.n.n.n form): 10.0.100.1 Slave Interface: eth1 MII Status: up Link Failure Count: 1 Permanent HW addr: 00:40:05:30:ff:30 Slave Interface: eth0 MII Status: up Link Failure Count: 0 Permanent HW addr: 00:13:21:be:33:e9 Signed-off-by: Andy Gospodarek Signed-off-by: Jay Vosburgh Signed-off-by: David S. Miller --- diff --git a/drivers/net/bonding/bond_main.c b/drivers/net/bonding/bond_main.c index 3f0071cfe56b..6a42a1453afa 100644 --- a/drivers/net/bonding/bond_main.c +++ b/drivers/net/bonding/bond_main.c @@ -2615,6 +2615,17 @@ static int bond_arp_rcv(struct sk_buff *skb, struct net_device *dev, struct pack unsigned char *arp_ptr; __be32 sip, tip; + if (dev->priv_flags & IFF_802_1Q_VLAN) { + /* + * When using VLANS and bonding, dev and oriv_dev may be + * incorrect if the physical interface supports VLAN + * acceleration. With this change ARP validation now + * works for hosts only reachable on the VLAN interface. + */ + dev = vlan_dev_real_dev(dev); + orig_dev = dev_get_by_index_rcu(dev_net(skb->dev),skb->skb_iif); + } + if (!(dev->priv_flags & IFF_BONDING) || !(dev->flags & IFF_MASTER)) goto out; diff --git a/net/8021q/vlan_core.c b/net/8021q/vlan_core.c index e75a2f3b10af..c0316e0ca6e8 100644 --- a/net/8021q/vlan_core.c +++ b/net/8021q/vlan_core.c @@ -14,6 +14,7 @@ int __vlan_hwaccel_rx(struct sk_buff *skb, struct vlan_group *grp, if (skb_bond_should_drop(skb)) goto drop; + skb->skb_iif = skb->dev->ifindex; __vlan_hwaccel_put_tag(skb, vlan_tci); skb->dev = vlan_group_get_device(grp, vlan_tci & VLAN_VID_MASK); @@ -85,6 +86,7 @@ vlan_gro_common(struct napi_struct *napi, struct vlan_group *grp, if (skb_bond_should_drop(skb)) goto drop; + skb->skb_iif = skb->dev->ifindex; __vlan_hwaccel_put_tag(skb, vlan_tci); skb->dev = vlan_group_get_device(grp, vlan_tci & VLAN_VID_MASK); diff --git a/net/core/dev.c b/net/core/dev.c index a8d68cdedbbe..f9aa699ab6cb 100644 --- a/net/core/dev.c +++ b/net/core/dev.c @@ -2495,12 +2495,26 @@ ncls: if (!skb) goto out; + /* + * Make sure frames received on VLAN interfaces stacked on + * bonding interfaces still make their way to any base bonding + * device that may have registered for a specific ptype. The + * handler may have to adjust skb->dev and orig_dev. + * + * null_or_orig can be overloaded since it will not be set when + * using VLANs on top of bonding. Putting it here prevents + * disturbing the ptype_all handlers above. + */ + if ((skb->dev->priv_flags & IFF_802_1Q_VLAN) && + (vlan_dev_real_dev(skb->dev)->priv_flags & IFF_BONDING)) { + null_or_orig = vlan_dev_real_dev(skb->dev); + } + type = skb->protocol; list_for_each_entry_rcu(ptype, &ptype_base[ntohs(type) & PTYPE_HASH_MASK], list) { - if (ptype->type == type && - (ptype->dev == null_or_orig || ptype->dev == skb->dev || - ptype->dev == orig_dev)) { + if (ptype->type == type && (ptype->dev == null_or_orig || + ptype->dev == skb->dev || ptype->dev == orig_dev)) { if (pt_prev) ret = deliver_skb(skb, pt_prev, orig_dev); pt_prev = ptype;