From: Stephen Warren Date: Thu, 21 Jun 2012 20:24:57 +0000 (-0600) Subject: ARM: dt: tegra: paz00: add regulators X-Git-Url: https://git.karo-electronics.de/?a=commitdiff_plain;h=217b8f0f357798270d9be396931e41e28ea2d00c;p=linux-beck.git ARM: dt: tegra: paz00: add regulators The Toshiba AC100/PAZ00 uses a TPS6586x regulator. Instantiate this. Three data sources were used for the data encoded here: * The HW defaults, as extracted from real HW. * The schematic, which specifies a voltage for each rail in the signal names. * The AC100 kernel used by the Ubuntu port: repo git://gitorious.org/~marvin24/ac100/marvin24s-kernel.git branch chromeos-ac100-3.0 file arch/arm/mach-tegra/board-paz00-power.c For many rails, the constraints in that tree specified differing min and max voltages. In all cases, the min value was ignored, since there's no need currently to vary any of the voltages at run-time. DVFS might change this in the future. In most cases these sources all matched. Differences are: sm0: HW defaults and schematic match at 1.2v. marvin24's kernel had a max of 1.3v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. sm1: HW defaults and schematic match at 1.0v. marvin24's kernel had a max of 1.125v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. ldo3: The HW default is on. marvin24's kernel didn't specify always-on, but since the board wasn't marked as having fully constrained regulators, the rail was not turned off, so the difference had no effect. The rail is needed for USB. ldo6: The HW default is 2.85v. The schematics indicate 2.85v. However, since this regulator is used for the same purpose as on other boards that require 1.8v, this is set to 1.8v. Note that this regulator feeds the CRT VDAC on Tegra, and so in practice is unlikely to be used, even though it is actaully hooked up in HW. Portions based on work by Laxman Dewangan Signed-off-by: Stephen Warren Tested-by: Marc Dietrich # v2 Acked-by: Laxman Dewangan --- diff --git a/arch/arm/boot/dts/tegra20-paz00.dts b/arch/arm/boot/dts/tegra20-paz00.dts index 684a9e1ff7e9..ddf287f52d49 100644 --- a/arch/arm/boot/dts/tegra20-paz00.dts +++ b/arch/arm/boot/dts/tegra20-paz00.dts @@ -272,12 +272,170 @@ status = "okay"; clock-frequency = <400000>; + pmic: tps6586x@34 { + compatible = "ti,tps6586x"; + reg = <0x34>; + interrupts = <0 86 0x4>; + + #gpio-cells = <2>; + gpio-controller; + + sys-supply = <&p5valw_reg>; + vin-sm0-supply = <&sys_reg>; + vin-sm1-supply = <&sys_reg>; + vin-sm2-supply = <&sys_reg>; + vinldo01-supply = <&sm2_reg>; + vinldo23-supply = <&sm2_reg>; + vinldo4-supply = <&sm2_reg>; + vinldo678-supply = <&sm2_reg>; + vinldo9-supply = <&sm2_reg>; + + regulators { + #address-cells = <1>; + #size-cells = <0>; + + sys_reg: regulator@0 { + reg = <0>; + regulator-compatible = "sys"; + regulator-name = "vdd_sys"; + regulator-always-on; + }; + + regulator@1 { + reg = <1>; + regulator-compatible = "sm0"; + regulator-name = "+1.2vs_sm0,vdd_core"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + }; + + regulator@2 { + reg = <2>; + regulator-compatible = "sm1"; + regulator-name = "+1.0vs_sm1,vdd_cpu"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + sm2_reg: regulator@3 { + reg = <3>; + regulator-compatible = "sm2"; + regulator-name = "+3.7vs_sm2,vin_ldo*"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + regulator-always-on; + }; + + /* LDO0 is not connected to anything */ + + regulator@5 { + reg = <5>; + regulator-compatible = "ldo1"; + regulator-name = "+1.1vs_ldo1,avdd_pll*"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + regulator@6 { + reg = <6>; + regulator-compatible = "ldo2"; + regulator-name = "+1.2vs_ldo2,vdd_rtc"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + regulator@7 { + reg = <7>; + regulator-compatible = "ldo3"; + regulator-name = "+3.3vs_ldo3,avdd_usb*"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + regulator@8 { + reg = <8>; + regulator-compatible = "ldo4"; + regulator-name = "+1.8vs_ldo4,avdd_osc,vddio_sys"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + regulator@9 { + reg = <9>; + regulator-compatible = "ldo5"; + regulator-name = "+2.85vs_ldo5,vcore_mmc"; + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + regulator-always-on; + }; + + regulator@10 { + reg = <10>; + regulator-compatible = "ldo6"; + /* + * Research indicates this should be + * 1.8v; other boards that use this + * rail for the same purpose need it + * set to 1.8v. The schematic signal + * name is incorrect; perhaps copied + * from an incorrect NVIDIA reference. + */ + regulator-name = "+2.85vs_ldo6,avdd_vdac"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + regulator@11 { + reg = <11>; + regulator-compatible = "ldo7"; + regulator-name = "+3.3vs_ldo7,avdd_hdmi"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + regulator@12 { + reg = <12>; + regulator-compatible = "ldo8"; + regulator-name = "+1.8vs_ldo8,avdd_hdmi_pll"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + regulator@13 { + reg = <13>; + regulator-compatible = "ldo9"; + regulator-name = "+2.85vs_ldo9,vdd_ddr_rx"; + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + regulator-always-on; + }; + + regulator@14 { + reg = <14>; + regulator-compatible = "ldo_rtc"; + regulator-name = "+3.3vs_rtc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + }; + adt7461@4c { compatible = "adi,adt7461"; reg = <0x4c>; }; }; + pmc { + nvidia,invert-interrupt; + }; + usb@c5000000 { status = "okay"; }; @@ -325,6 +483,21 @@ }; }; + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + p5valw_reg: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "+5valw"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + }; + sound { compatible = "nvidia,tegra-audio-alc5632-paz00", "nvidia,tegra-audio-alc5632";