From: Gaurav K Singh Date: Fri, 5 Dec 2014 08:54:21 +0000 (+0530) Subject: drm/i915: Update the DSI enable path to support dual X-Git-Url: https://git.karo-electronics.de/?a=commitdiff_plain;h=24ee0e64909bf7f1953d87d3e1e29d93eafcad73;p=linux-beck.git drm/i915: Update the DSI enable path to support dual We need to program both port registers during dual link enable path. v2: Address review comments by Jani - Used a for loop instead of do-while loop. v3: Used for_each_dsi_port macro instead of for loop v4: Renamed mode_hactive variable to mode_hdisplay Signed-off-by: Gaurav K Singh Signed-off-by: Shobhit Kumar Reviewed-by: Jani Nikula Signed-off-by: Daniel Vetter --- diff --git a/drivers/gpu/drm/i915/intel_dsi.c b/drivers/gpu/drm/i915/intel_dsi.c index 805492840231..8f8b952eaa92 100644 --- a/drivers/gpu/drm/i915/intel_dsi.c +++ b/drivers/gpu/drm/i915/intel_dsi.c @@ -156,8 +156,8 @@ static void intel_dsi_port_disable(struct intel_encoder *encoder) static void intel_dsi_device_ready(struct intel_encoder *encoder) { struct drm_i915_private *dev_priv = encoder->base.dev->dev_private; - struct intel_crtc *intel_crtc = to_intel_crtc(encoder->base.crtc); - enum port port = intel_dsi_pipe_to_port(intel_crtc->pipe); + struct intel_dsi *intel_dsi = enc_to_intel_dsi(&encoder->base); + enum port port; u32 val; DRM_DEBUG_KMS("\n"); @@ -171,18 +171,21 @@ static void intel_dsi_device_ready(struct intel_encoder *encoder) /* bandgap reset is needed after everytime we do power gate */ band_gap_reset(dev_priv); - I915_WRITE(MIPI_DEVICE_READY(port), ULPS_STATE_ENTER); - usleep_range(2500, 3000); + for_each_dsi_port(port, intel_dsi->ports) { - val = I915_READ(MIPI_PORT_CTRL(port)); - I915_WRITE(MIPI_PORT_CTRL(port), val | LP_OUTPUT_HOLD); - usleep_range(1000, 1500); + I915_WRITE(MIPI_DEVICE_READY(port), ULPS_STATE_ENTER); + usleep_range(2500, 3000); - I915_WRITE(MIPI_DEVICE_READY(port), ULPS_STATE_EXIT); - usleep_range(2500, 3000); + val = I915_READ(MIPI_PORT_CTRL(port)); + I915_WRITE(MIPI_PORT_CTRL(port), val | LP_OUTPUT_HOLD); + usleep_range(1000, 1500); - I915_WRITE(MIPI_DEVICE_READY(port), DEVICE_READY); - usleep_range(2500, 3000); + I915_WRITE(MIPI_DEVICE_READY(port), ULPS_STATE_EXIT); + usleep_range(2500, 3000); + + I915_WRITE(MIPI_DEVICE_READY(port), DEVICE_READY); + usleep_range(2500, 3000); + } } static void intel_dsi_enable(struct intel_encoder *encoder) @@ -547,32 +550,43 @@ static void intel_dsi_prepare(struct intel_encoder *intel_encoder) struct intel_dsi *intel_dsi = enc_to_intel_dsi(encoder); struct drm_display_mode *adjusted_mode = &intel_crtc->config.adjusted_mode; - enum port port = intel_dsi_pipe_to_port(intel_crtc->pipe); + enum port port; unsigned int bpp = intel_crtc->config.pipe_bpp; u32 val, tmp; + u16 mode_hdisplay; DRM_DEBUG_KMS("pipe %c\n", pipe_name(intel_crtc->pipe)); - /* escape clock divider, 20MHz, shared for A and C. device ready must be - * off when doing this! txclkesc? */ - tmp = I915_READ(MIPI_CTRL(PORT_A)); - tmp &= ~ESCAPE_CLOCK_DIVIDER_MASK; - I915_WRITE(MIPI_CTRL(PORT_A), tmp | ESCAPE_CLOCK_DIVIDER_1); - - /* read request priority is per pipe */ - tmp = I915_READ(MIPI_CTRL(port)); - tmp &= ~READ_REQUEST_PRIORITY_MASK; - I915_WRITE(MIPI_CTRL(port), tmp | READ_REQUEST_PRIORITY_HIGH); + mode_hdisplay = adjusted_mode->hdisplay; - /* XXX: why here, why like this? handling in irq handler?! */ - I915_WRITE(MIPI_INTR_STAT(port), 0xffffffff); - I915_WRITE(MIPI_INTR_EN(port), 0xffffffff); - - I915_WRITE(MIPI_DPHY_PARAM(port), intel_dsi->dphy_reg); + if (intel_dsi->dual_link) { + mode_hdisplay /= 2; + if (intel_dsi->dual_link == DSI_DUAL_LINK_FRONT_BACK) + mode_hdisplay += intel_dsi->pixel_overlap; + } - I915_WRITE(MIPI_DPI_RESOLUTION(port), - adjusted_mode->vdisplay << VERTICAL_ADDRESS_SHIFT | - adjusted_mode->hdisplay << HORIZONTAL_ADDRESS_SHIFT); + for_each_dsi_port(port, intel_dsi->ports) { + /* escape clock divider, 20MHz, shared for A and C. + * device ready must be off when doing this! txclkesc? */ + tmp = I915_READ(MIPI_CTRL(PORT_A)); + tmp &= ~ESCAPE_CLOCK_DIVIDER_MASK; + I915_WRITE(MIPI_CTRL(PORT_A), tmp | ESCAPE_CLOCK_DIVIDER_1); + + /* read request priority is per pipe */ + tmp = I915_READ(MIPI_CTRL(port)); + tmp &= ~READ_REQUEST_PRIORITY_MASK; + I915_WRITE(MIPI_CTRL(port), tmp | READ_REQUEST_PRIORITY_HIGH); + + /* XXX: why here, why like this? handling in irq handler?! */ + I915_WRITE(MIPI_INTR_STAT(port), 0xffffffff); + I915_WRITE(MIPI_INTR_EN(port), 0xffffffff); + + I915_WRITE(MIPI_DPHY_PARAM(port), intel_dsi->dphy_reg); + + I915_WRITE(MIPI_DPI_RESOLUTION(port), + adjusted_mode->vdisplay << VERTICAL_ADDRESS_SHIFT | + mode_hdisplay << HORIZONTAL_ADDRESS_SHIFT); + } set_dsi_timings(encoder, adjusted_mode); @@ -586,95 +600,102 @@ static void intel_dsi_prepare(struct intel_encoder *intel_encoder) /* XXX: cross-check bpp vs. pixel format? */ val |= intel_dsi->pixel_format; } - I915_WRITE(MIPI_DSI_FUNC_PRG(port), val); - /* timeouts for recovery. one frame IIUC. if counter expires, EOT and - * stop state. */ - - /* - * In burst mode, value greater than one DPI line Time in byte clock - * (txbyteclkhs) To timeout this timer 1+ of the above said value is - * recommended. - * - * In non-burst mode, Value greater than one DPI frame time in byte - * clock(txbyteclkhs) To timeout this timer 1+ of the above said value - * is recommended. - * - * In DBI only mode, value greater than one DBI frame time in byte - * clock(txbyteclkhs) To timeout this timer 1+ of the above said value - * is recommended. - */ - - if (is_vid_mode(intel_dsi) && - intel_dsi->video_mode_format == VIDEO_MODE_BURST) { - I915_WRITE(MIPI_HS_TX_TIMEOUT(port), - txbyteclkhs(adjusted_mode->htotal, bpp, - intel_dsi->lane_count, - intel_dsi->burst_mode_ratio) + 1); - } else { - I915_WRITE(MIPI_HS_TX_TIMEOUT(port), - txbyteclkhs(adjusted_mode->vtotal * - adjusted_mode->htotal, - bpp, intel_dsi->lane_count, - intel_dsi->burst_mode_ratio) + 1); - } - I915_WRITE(MIPI_LP_RX_TIMEOUT(port), intel_dsi->lp_rx_timeout); - I915_WRITE(MIPI_TURN_AROUND_TIMEOUT(port), intel_dsi->turn_arnd_val); - I915_WRITE(MIPI_DEVICE_RESET_TIMER(port), intel_dsi->rst_timer_val); + tmp = 0; + if (intel_dsi->eotp_pkt == 0) + tmp |= EOT_DISABLE; + if (intel_dsi->clock_stop) + tmp |= CLOCKSTOP; - /* dphy stuff */ + for_each_dsi_port(port, intel_dsi->ports) { + I915_WRITE(MIPI_DSI_FUNC_PRG(port), val); + + /* timeouts for recovery. one frame IIUC. if counter expires, + * EOT and stop state. */ + + /* + * In burst mode, value greater than one DPI line Time in byte + * clock (txbyteclkhs) To timeout this timer 1+ of the above + * said value is recommended. + * + * In non-burst mode, Value greater than one DPI frame time in + * byte clock(txbyteclkhs) To timeout this timer 1+ of the above + * said value is recommended. + * + * In DBI only mode, value greater than one DBI frame time in + * byte clock(txbyteclkhs) To timeout this timer 1+ of the above + * said value is recommended. + */ - /* in terms of low power clock */ - I915_WRITE(MIPI_INIT_COUNT(port), txclkesc(intel_dsi->escape_clk_div, 100)); + if (is_vid_mode(intel_dsi) && + intel_dsi->video_mode_format == VIDEO_MODE_BURST) { + I915_WRITE(MIPI_HS_TX_TIMEOUT(port), + txbyteclkhs(adjusted_mode->htotal, bpp, + intel_dsi->lane_count, + intel_dsi->burst_mode_ratio) + 1); + } else { + I915_WRITE(MIPI_HS_TX_TIMEOUT(port), + txbyteclkhs(adjusted_mode->vtotal * + adjusted_mode->htotal, + bpp, intel_dsi->lane_count, + intel_dsi->burst_mode_ratio) + 1); + } + I915_WRITE(MIPI_LP_RX_TIMEOUT(port), intel_dsi->lp_rx_timeout); + I915_WRITE(MIPI_TURN_AROUND_TIMEOUT(port), + intel_dsi->turn_arnd_val); + I915_WRITE(MIPI_DEVICE_RESET_TIMER(port), + intel_dsi->rst_timer_val); - val = 0; - if (intel_dsi->eotp_pkt == 0) - val |= EOT_DISABLE; + /* dphy stuff */ - if (intel_dsi->clock_stop) - val |= CLOCKSTOP; + /* in terms of low power clock */ + I915_WRITE(MIPI_INIT_COUNT(port), + txclkesc(intel_dsi->escape_clk_div, 100)); - /* recovery disables */ - I915_WRITE(MIPI_EOT_DISABLE(port), val); - /* in terms of low power clock */ - I915_WRITE(MIPI_INIT_COUNT(port), intel_dsi->init_count); + /* recovery disables */ + I915_WRITE(MIPI_EOT_DISABLE(port), val); - /* in terms of txbyteclkhs. actual high to low switch + - * MIPI_STOP_STATE_STALL * MIPI_LP_BYTECLK. - * - * XXX: write MIPI_STOP_STATE_STALL? - */ - I915_WRITE(MIPI_HIGH_LOW_SWITCH_COUNT(port), - intel_dsi->hs_to_lp_count); + /* in terms of low power clock */ + I915_WRITE(MIPI_INIT_COUNT(port), intel_dsi->init_count); - /* XXX: low power clock equivalence in terms of byte clock. the number - * of byte clocks occupied in one low power clock. based on txbyteclkhs - * and txclkesc. txclkesc time / txbyteclk time * (105 + - * MIPI_STOP_STATE_STALL) / 105.??? - */ - I915_WRITE(MIPI_LP_BYTECLK(port), intel_dsi->lp_byte_clk); - - /* the bw essential for transmitting 16 long packets containing 252 - * bytes meant for dcs write memory command is programmed in this - * register in terms of byte clocks. based on dsi transfer rate and the - * number of lanes configured the time taken to transmit 16 long packets - * in a dsi stream varies. */ - I915_WRITE(MIPI_DBI_BW_CTRL(port), intel_dsi->bw_timer); - - I915_WRITE(MIPI_CLK_LANE_SWITCH_TIME_CNT(port), - intel_dsi->clk_lp_to_hs_count << LP_HS_SSW_CNT_SHIFT | - intel_dsi->clk_hs_to_lp_count << HS_LP_PWR_SW_CNT_SHIFT); - - if (is_vid_mode(intel_dsi)) - /* Some panels might have resolution which is not a multiple of - * 64 like 1366 x 768. Enable RANDOM resolution support for such - * panels by default */ - I915_WRITE(MIPI_VIDEO_MODE_FORMAT(port), - intel_dsi->video_frmt_cfg_bits | - intel_dsi->video_mode_format | - IP_TG_CONFIG | - RANDOM_DPI_DISPLAY_RESOLUTION); + /* in terms of txbyteclkhs. actual high to low switch + + * MIPI_STOP_STATE_STALL * MIPI_LP_BYTECLK. + * + * XXX: write MIPI_STOP_STATE_STALL? + */ + I915_WRITE(MIPI_HIGH_LOW_SWITCH_COUNT(port), + intel_dsi->hs_to_lp_count); + + /* XXX: low power clock equivalence in terms of byte clock. + * the number of byte clocks occupied in one low power clock. + * based on txbyteclkhs and txclkesc. + * txclkesc time / txbyteclk time * (105 + MIPI_STOP_STATE_STALL + * ) / 105.??? + */ + I915_WRITE(MIPI_LP_BYTECLK(port), intel_dsi->lp_byte_clk); + + /* the bw essential for transmitting 16 long packets containing + * 252 bytes meant for dcs write memory command is programmed in + * this register in terms of byte clocks. based on dsi transfer + * rate and the number of lanes configured the time taken to + * transmit 16 long packets in a dsi stream varies. */ + I915_WRITE(MIPI_DBI_BW_CTRL(port), intel_dsi->bw_timer); + + I915_WRITE(MIPI_CLK_LANE_SWITCH_TIME_CNT(port), + intel_dsi->clk_lp_to_hs_count << LP_HS_SSW_CNT_SHIFT | + intel_dsi->clk_hs_to_lp_count << HS_LP_PWR_SW_CNT_SHIFT); + + if (is_vid_mode(intel_dsi)) + /* Some panels might have resolution which is not a + * multiple of 64 like 1366 x 768. Enable RANDOM + * resolution support for such panels by default */ + I915_WRITE(MIPI_VIDEO_MODE_FORMAT(port), + intel_dsi->video_frmt_cfg_bits | + intel_dsi->video_mode_format | + IP_TG_CONFIG | + RANDOM_DPI_DISPLAY_RESOLUTION); + } } static void intel_dsi_pre_pll_enable(struct intel_encoder *encoder)