From: Magnus Damm Date: Wed, 22 Dec 2010 12:17:09 +0000 (+0000) Subject: ARM: mach-shmobile: Use shared GIC entry macros X-Git-Url: https://git.karo-electronics.de/?a=commitdiff_plain;h=3dff8804fc087d55c593dda0ff78f475088ec57d;p=linux-beck.git ARM: mach-shmobile: Use shared GIC entry macros Use the GIC demux code in asm/hardware/entry-macro-gic.S on the R-Mobile / SH-Mobile processors. Signed-off-by: Magnus Damm Signed-off-by: Paul Mundt --- diff --git a/arch/arm/mach-shmobile/include/mach/entry-macro-gic.S b/arch/arm/mach-shmobile/include/mach/entry-macro-gic.S index 50b1f16d54a2..48872dd15269 100644 --- a/arch/arm/mach-shmobile/include/mach/entry-macro-gic.S +++ b/arch/arm/mach-shmobile/include/mach/entry-macro-gic.S @@ -16,6 +16,7 @@ */ #include #include +#include .macro disable_fiq .endm @@ -26,64 +27,3 @@ .macro arch_ret_to_user, tmp1, tmp2 .endm - - /* - * The interrupt numbering scheme is defined in the - * interrupt controller spec. To wit: - * - * Interrupts 0-15 are IPI - * 16-28 are reserved - * 29-31 are local. We allow 30 to be used for the watchdog. - * 32-1020 are global - * 1021-1022 are reserved - * 1023 is "spurious" (no interrupt) - * - * For now, we ignore all local interrupts so only return an - * interrupt if it's between 30 and 1020. The test_for_ipi - * routine below will pick up on IPIs. - * - * A simple read from the controller will tell us the number of - * the highest priority enabled interrupt. We then just need to - * check whether it is in the valid range for an IRQ (30-1020 - * inclusive). - */ - - .macro get_irqnr_and_base, irqnr, irqstat, base, tmp - - ldr \irqstat, [\base, #GIC_CPU_INTACK] - /* bits 12-10 = src CPU, 9-0 = int # */ - - ldr \tmp, =1021 - bic \irqnr, \irqstat, #0x1c00 - cmp \irqnr, #29 - cmpcc \irqnr, \irqnr - cmpne \irqnr, \tmp - cmpcs \irqnr, \irqnr - - .endm - - /* - * We assume that irqstat (the raw value of the IRQ acknowledge - * register) is preserved from the macro above. - * If there is an IPI, we immediately signal end of interrupt on the - * controller, since this requires the original irqstat value which - * we won't easily be able to recreate later. - */ - - .macro test_for_ipi, irqnr, irqstat, base, tmp - bic \irqnr, \irqstat, #0x1c00 - cmp \irqnr, #16 - strcc \irqstat, [\base, #GIC_CPU_EOI] - cmpcs \irqnr, \irqnr - .endm - - /* As above, this assumes that irqstat and base are preserved.. */ - - .macro test_for_ltirq, irqnr, irqstat, base, tmp - bic \irqnr, \irqstat, #0x1c00 - mov \tmp, #0 - cmp \irqnr, #29 - moveq \tmp, #1 - streq \irqstat, [\base, #GIC_CPU_EOI] - cmp \tmp, #0 - .endm