From: Geert Uytterhoeven Date: Mon, 15 Oct 2012 20:13:12 +0000 (+0200) Subject: serial/8250_hp300: Missing 8250 register interface conversion bits X-Git-Url: https://git.karo-electronics.de/?a=commitdiff_plain;h=3e5bde8ef4cc9e719b492726dd82a43d29468cd0;p=linux-beck.git serial/8250_hp300: Missing 8250 register interface conversion bits commit 2655a2c76f80d91da34faa8f4e114d1793435ed3 ("8250: use the 8250 register interface not the legacy one") forgot to fully switch one instance of struct uart_port to struct uart_8250_port, causing the following compile failure: drivers/tty/serial/8250/8250_hp300.c: In function ‘hpdca_init_one’: drivers/tty/serial/8250/8250_hp300.c:174: error: ‘uart’ undeclared (first use in this function) drivers/tty/serial/8250/8250_hp300.c:174: error: (Each undeclared identifier is reported only once drivers/tty/serial/8250/8250_hp300.c:174: error: for each function it appears in.) This went unnoticed in -next, as CONFIG_HPDCA is not set to y by allmodconfig. Reported-by: Fengguang Wu Cc: Alan Cox Cc: Philip Blundell Signed-off-by: Geert Uytterhoeven Signed-off-by: Greg Kroah-Hartman --- diff --git a/drivers/tty/serial/8250/8250_hp300.c b/drivers/tty/serial/8250/8250_hp300.c index 8f1dd2cc00a8..f3d0edf46644 100644 --- a/drivers/tty/serial/8250/8250_hp300.c +++ b/drivers/tty/serial/8250/8250_hp300.c @@ -162,7 +162,7 @@ int __init hp300_setup_serial_console(void) static int __devinit hpdca_init_one(struct dio_dev *d, const struct dio_device_id *ent) { - struct uart_port port; + struct uart_8250_port uart; int line; #ifdef CONFIG_SERIAL_8250_CONSOLE @@ -174,19 +174,19 @@ static int __devinit hpdca_init_one(struct dio_dev *d, memset(&uart, 0, sizeof(uart)); /* Memory mapped I/O */ - port.iotype = UPIO_MEM; - port.flags = UPF_SKIP_TEST | UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF; - port.irq = d->ipl; - port.uartclk = HPDCA_BAUD_BASE * 16; - port.mapbase = (d->resource.start + UART_OFFSET); - port.membase = (char *)(port.mapbase + DIO_VIRADDRBASE); - port.regshift = 1; - port.dev = &d->dev; + uart.port.iotype = UPIO_MEM; + uart.port.flags = UPF_SKIP_TEST | UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF; + uart.port.irq = d->ipl; + uart.port.uartclk = HPDCA_BAUD_BASE * 16; + uart.port.mapbase = (d->resource.start + UART_OFFSET); + uart.port.membase = (char *)(uart.port.mapbase + DIO_VIRADDRBASE); + uart.port.regshift = 1; + uart.port.dev = &d->dev; line = serial8250_register_8250_port(&uart); if (line < 0) { printk(KERN_NOTICE "8250_hp300: register_serial() DCA scode %d" - " irq %d failed\n", d->scode, port.irq); + " irq %d failed\n", d->scode, uart.port.irq); return -ENOMEM; }