From: Jes Sorensen Date: Mon, 29 Feb 2016 22:04:52 +0000 (-0500) Subject: rtl8xxxu: Implement 8723bu power on sequence X-Git-Url: https://git.karo-electronics.de/?a=commitdiff_plain;h=42836db1f609b66fdb1b307243fa01451748ab68;p=linux-beck.git rtl8xxxu: Implement 8723bu power on sequence This implements the 8723bu specific power on sequence as it is different from that of the 8723au chips. Signed-off-by: Jes Sorensen Signed-off-by: Kalle Valo --- diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c index a41f7f0e5b0b..1f30b3bb5daf 100644 --- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c +++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c @@ -2933,10 +2933,6 @@ static void rtl8723bu_phy_init_antenna_selection(struct rtl8xxxu_priv *priv) val32 &= 0xffffff00; val32 |= 0x77; rtl8xxxu_write32(priv, 0x0930, val32); - - val32 = rtl8xxxu_read32(priv, REG_PWR_DATA); - val32 |= BIT(11); - rtl8xxxu_write32(priv, REG_PWR_DATA, val32); } static int @@ -5359,6 +5355,127 @@ exit: return ret; } +static int rtl8723b_emu_to_active(struct rtl8xxxu_priv *priv) +{ + u8 val8; + u32 val32; + int count, ret = 0; + + /* 0x20[0] = 1 enable LDOA12 MACRO block for all interface */ + val8 = rtl8xxxu_read8(priv, REG_LDOA15_CTRL); + val8 |= LDOA15_ENABLE; + rtl8xxxu_write8(priv, REG_LDOA15_CTRL, val8); + + /* 0x67[0] = 0 to disable BT_GPS_SEL pins*/ + val8 = rtl8xxxu_read8(priv, 0x0067); + val8 &= ~BIT(4); + rtl8xxxu_write8(priv, 0x0067, val8); + + mdelay(1); + + /* 0x00[5] = 0 release analog Ips to digital, 1:isolation */ + val8 = rtl8xxxu_read8(priv, REG_SYS_ISO_CTRL); + val8 &= ~SYS_ISO_ANALOG_IPS; + rtl8xxxu_write8(priv, REG_SYS_ISO_CTRL, val8); + + /* Disable SW LPS 0x04[10]= 0 */ + val32 = rtl8xxxu_read8(priv, REG_APS_FSMCO); + val32 &= ~APS_FSMCO_SW_LPS; + rtl8xxxu_write32(priv, REG_APS_FSMCO, val32); + + /* Wait until 0x04[17] = 1 power ready */ + for (count = RTL8XXXU_MAX_REG_POLL; count; count--) { + val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO); + if (val32 & BIT(17)) + break; + + udelay(10); + } + + if (!count) { + ret = -EBUSY; + goto exit; + } + + /* We should be able to optimize the following three entries into one */ + + /* Release WLON reset 0x04[16]= 1*/ + val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO); + val32 |= APS_FSMCO_WLON_RESET; + rtl8xxxu_write32(priv, REG_APS_FSMCO, val32); + + /* Disable HWPDN 0x04[15]= 0*/ + val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO); + val32 &= ~APS_FSMCO_HW_POWERDOWN; + rtl8xxxu_write32(priv, REG_APS_FSMCO, val32); + + /* Disable WL suspend*/ + val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO); + val32 &= ~(APS_FSMCO_HW_SUSPEND | APS_FSMCO_PCIE); + rtl8xxxu_write32(priv, REG_APS_FSMCO, val32); + + /* Set, then poll until 0 */ + val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO); + val32 |= APS_FSMCO_MAC_ENABLE; + rtl8xxxu_write32(priv, REG_APS_FSMCO, val32); + + for (count = RTL8XXXU_MAX_REG_POLL; count; count--) { + val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO); + if ((val32 & APS_FSMCO_MAC_ENABLE) == 0) { + ret = 0; + break; + } + udelay(10); + } + + if (!count) { + ret = -EBUSY; + goto exit; + } + + /* Enable WL control XTAL setting */ + val8 = rtl8xxxu_read8(priv, REG_AFE_MISC); + val8 |= AFE_MISC_WL_XTAL_CTRL; + rtl8xxxu_write8(priv, REG_AFE_MISC, val8); + + /* Enable falling edge triggering interrupt */ + val8 = rtl8xxxu_read8(priv, REG_GPIO_INTM + 1); + val8 |= BIT(1); + rtl8xxxu_write8(priv, REG_GPIO_INTM + 1, val8); + + /* Enable GPIO9 interrupt mode */ + val8 = rtl8xxxu_read8(priv, REG_GPIO_IO_SEL_2 + 1); + val8 |= BIT(1); + rtl8xxxu_write8(priv, REG_GPIO_IO_SEL_2 + 1, val8); + + /* Enable GPIO9 input mode */ + val8 = rtl8xxxu_read8(priv, REG_GPIO_IO_SEL_2); + val8 &= ~BIT(1); + rtl8xxxu_write8(priv, REG_GPIO_IO_SEL_2, val8); + + /* Enable HSISR GPIO[C:0] interrupt */ + val8 = rtl8xxxu_read8(priv, REG_HSIMR); + val8 |= BIT(0); + rtl8xxxu_write8(priv, REG_HSIMR, val8); + + /* Enable HSISR GPIO9 interrupt */ + val8 = rtl8xxxu_read8(priv, REG_HSIMR + 2); + val8 |= BIT(1); + rtl8xxxu_write8(priv, REG_HSIMR + 2, val8); + + val8 = rtl8xxxu_read8(priv, REG_MULTI_FUNC_CTRL); + val8 |= MULTI_WIFI_HW_ROF_EN; + rtl8xxxu_write8(priv, REG_MULTI_FUNC_CTRL, val8); + + /* For GPIO9 internal pull high setting BIT(14) */ + val8 = rtl8xxxu_read8(priv, REG_MULTI_FUNC_CTRL + 1); + val8 |= BIT(6); + rtl8xxxu_write8(priv, REG_MULTI_FUNC_CTRL + 1, val8); + +exit: + return ret; +} + static int rtl8xxxu_emu_to_disabled(struct rtl8xxxu_priv *priv) { u8 val8; @@ -5430,6 +5547,62 @@ exit: return ret; } +static int rtl8723bu_power_on(struct rtl8xxxu_priv *priv) +{ + u8 val8; + u16 val16; + u32 val32; + int ret; + + rtl8723a_disabled_to_emu(priv); + + ret = rtl8723b_emu_to_active(priv); + if (ret) + goto exit; + + /* + * Enable MAC DMA/WMAC/SCHEDULE/SEC block + * Set CR bit10 to enable 32k calibration. + */ + val16 = rtl8xxxu_read16(priv, REG_CR); + val16 |= (CR_HCI_TXDMA_ENABLE | CR_HCI_RXDMA_ENABLE | + CR_TXDMA_ENABLE | CR_RXDMA_ENABLE | + CR_PROTOCOL_ENABLE | CR_SCHEDULE_ENABLE | + CR_MAC_TX_ENABLE | CR_MAC_RX_ENABLE | + CR_SECURITY_ENABLE | CR_CALTIMER_ENABLE); + rtl8xxxu_write16(priv, REG_CR, val16); + + /* + * BT coexist power on settings. This is identical for 1 and 2 + * antenna parts. + */ + rtl8xxxu_write8(priv, REG_PAD_CTRL1 + 3, 0x20); + + val16 = rtl8xxxu_read16(priv, REG_SYS_FUNC); + val16 |= SYS_FUNC_BBRSTB | SYS_FUNC_BB_GLB_RSTN; + rtl8xxxu_write16(priv, REG_SYS_FUNC, val16); + + rtl8xxxu_write8(priv, REG_BT_CONTROL_8723BU + 1, 0x18); + rtl8xxxu_write8(priv, REG_WLAN_ACT_CONTROL_8723B, 0x04); + rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00); + /* Antenna inverse */ + rtl8xxxu_write8(priv, 0xfe08, 0x01); + + val16 = rtl8xxxu_read16(priv, REG_PWR_DATA); + val16 |= PWR_DATA_EEPRPAD_RFE_CTRL_EN; + rtl8xxxu_write16(priv, REG_PWR_DATA, val16); + + val32 = rtl8xxxu_read32(priv, REG_LEDCFG0); + val32 |= LEDCFG0_DPDT_SELECT; + rtl8xxxu_write32(priv, REG_LEDCFG0, val32); + + val8 = rtl8xxxu_read8(priv, REG_PAD_CTRL1); + val8 &= ~PAD_CTRL1_SW_DPDT_SEL_DATA; + rtl8xxxu_write8(priv, REG_PAD_CTRL1, val8); +exit: + return ret; +} + #ifdef CONFIG_RTL8XXXU_UNTESTED static int rtl8192cu_power_on(struct rtl8xxxu_priv *priv) @@ -7707,7 +7880,7 @@ static struct rtl8xxxu_fileops rtl8723au_fops = { static struct rtl8xxxu_fileops rtl8723bu_fops = { .parse_efuse = rtl8723bu_parse_efuse, .load_firmware = rtl8723bu_load_firmware, - .power_on = rtl8723au_power_on, + .power_on = rtl8723bu_power_on, .llt_init = rtl8xxxu_auto_llt_table, .phy_init_antenna_selection = rtl8723bu_phy_init_antenna_selection, .phy_iq_calibrate = rtl8723bu_phy_iq_calibrate, diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h index a82c0ba7931d..5250388b0275 100644 --- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h +++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h @@ -70,6 +70,8 @@ #define REG_EE_VPD 0x000c #define REG_AFE_MISC 0x0010 +#define AFE_MISC_WL_XTAL_CTRL BIT(6) + #define REG_SPS0_CTRL 0x0011 #define REG_SPS_OCP_CFG 0x0018 #define REG_8192E_LDOV12_CTRL 0x0014 @@ -133,6 +135,8 @@ #define EFUSE_ACCESS_DISABLE 0x00 /* RTL8723 only */ #define REG_PWR_DATA 0x0038 +#define PWR_DATA_EEPRPAD_RFE_CTRL_EN BIT(11) + #define REG_CAL_TIMER 0x003c #define REG_ACLK_MON 0x003e #define REG_GPIO_MUXCFG 0x0040 @@ -140,7 +144,10 @@ #define REG_MAC_PINMUX_CFG 0x0043 #define REG_GPIO_PIN_CTRL 0x0044 #define REG_GPIO_INTM 0x0048 +#define GPIO_INTM_EDGE_TRIG_IRQ BIT(9) + #define REG_LEDCFG0 0x004c +#define LEDCFG0_DPDT_SELECT BIT(23) #define REG_LEDCFG1 0x004d #define REG_LEDCFG2 0x004e #define LEDCFG2_DPDT_SELECT BIT(7) @@ -154,9 +161,13 @@ #define REG_GPIO_PIN_CTRL_2 0x0060 /* RTL8723 WIFI/BT/GPS Multi-Function GPIO Select. */ #define REG_GPIO_IO_SEL_2 0x0062 +#define GPIO_IO_SEL_2_GPIO09_INPUT BIT(1) +#define GPIO_IO_SEL_2_GPIO09_IRQ BIT(9) /* RTL8723B */ #define REG_PAD_CTRL1 0x0064 +#define PAD_CTRL1_SW_DPDT_SEL_DATA BIT(0) + /* RTL8723 only WIFI/BT/GPS Multi-Function control source. */ #define REG_MULTI_FUNC_CTRL 0x0068