From: Ludovic Desroches <ludovic.desroches@atmel.com>
Date: Thu, 28 Apr 2016 12:59:26 +0000 (+0200)
Subject: mmc: sdhci-of-at91: add presets setup
X-Git-Url: https://git.karo-electronics.de/?a=commitdiff_plain;h=4406433dec687c54be48a18a71dd28acb319137e;p=linux-beck.git

mmc: sdhci-of-at91: add presets setup

The controller claims to support SDR104. In fact, it only supports a
degraded SDR104 since the maximum frequency of the SD clock is 120 MHz
instead of 208 MHz.
The sdhci core is unaware of it and will compute a wrong clock divider.
We can deal with this specific case by using presets.

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
---

diff --git a/drivers/mmc/host/sdhci-of-at91.c b/drivers/mmc/host/sdhci-of-at91.c
index c1923c094ff6..25f779e09d8e 100644
--- a/drivers/mmc/host/sdhci-of-at91.c
+++ b/drivers/mmc/host/sdhci-of-at91.c
@@ -18,6 +18,7 @@
 #include <linux/delay.h>
 #include <linux/err.h>
 #include <linux/io.h>
+#include <linux/kernel.h>
 #include <linux/mmc/host.h>
 #include <linux/mmc/slot-gpio.h>
 #include <linux/module.h>
@@ -32,6 +33,8 @@
 #define		SDMMC_CACR_CAPWREN	BIT(0)
 #define		SDMMC_CACR_KEY		(0x46 << 8)
 
+#define SDHCI_AT91_PRESET_COMMON_CONF	0x400 /* drv type B, programmable clock mode */
+
 struct sdhci_at91_priv {
 	struct clk *hclock;
 	struct clk *gck;
@@ -163,6 +166,7 @@ static int sdhci_at91_probe(struct platform_device *pdev)
 	unsigned int			clk_base, clk_mul;
 	unsigned int			gck_rate, real_gck_rate;
 	int				ret;
+	unsigned int			preset_div;
 
 	match = of_match_device(sdhci_at91_dt_match, &pdev->dev);
 	if (!match)
@@ -230,6 +234,28 @@ static int sdhci_at91_probe(struct platform_device *pdev)
 			 clk_mul, real_gck_rate);
 	}
 
+	/*
+	 * We have to set preset values because it depends on the clk_mul
+	 * value. Moreover, SDR104 is supported in a degraded mode since the
+	 * maximum sd clock value is 120 MHz instead of 208 MHz. For that
+	 * reason, we need to use presets to support SDR104.
+	 */
+	preset_div = DIV_ROUND_UP(real_gck_rate, 24000000) - 1;
+	writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
+	       host->ioaddr + SDHCI_PRESET_FOR_SDR12);
+	preset_div = DIV_ROUND_UP(real_gck_rate, 50000000) - 1;
+	writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
+	       host->ioaddr + SDHCI_PRESET_FOR_SDR25);
+	preset_div = DIV_ROUND_UP(real_gck_rate, 100000000) - 1;
+	writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
+	       host->ioaddr + SDHCI_PRESET_FOR_SDR50);
+	preset_div = DIV_ROUND_UP(real_gck_rate, 120000000) - 1;
+	writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
+	       host->ioaddr + SDHCI_PRESET_FOR_SDR104);
+	preset_div = DIV_ROUND_UP(real_gck_rate, 50000000) - 1;
+	writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
+	       host->ioaddr + SDHCI_PRESET_FOR_DDR50);
+
 	clk_prepare_enable(priv->mainck);
 	clk_prepare_enable(priv->gck);