From: Wolfram Sang Date: Thu, 17 Dec 2015 12:32:36 +0000 (+0100) Subject: i2c: make i2c_parse_fw_timings() always visible X-Git-Url: https://git.karo-electronics.de/?a=commitdiff_plain;h=54177ccfbe95fcf250a89508a705bfe4706e3b86;p=linux-beck.git i2c: make i2c_parse_fw_timings() always visible This function used to be DT only, so it lived inside a CONFIG_OF block. Now it uses device attributes and must be moved outside of it. No further code changes, only one whitespace improvement. Reported-by: Jim Davis Signed-off-by: Wolfram Sang Reviewed-by: Mika Westerberg Signed-off-by: Wolfram Sang --- diff --git a/drivers/i2c/i2c-core.c b/drivers/i2c/i2c-core.c index b34c412bd2c2..7349b00f4101 100644 --- a/drivers/i2c/i2c-core.c +++ b/drivers/i2c/i2c-core.c @@ -1439,58 +1439,6 @@ static void of_i2c_register_devices(struct i2c_adapter *adap) } } -/** - * i2c_parse_fw_timings - get I2C related timing parameters from firmware - * @dev: The device to scan for I2C timing properties - * @t: the i2c_timings struct to be filled with values - * @use_defaults: bool to use sane defaults derived from the I2C specification - * when properties are not found, otherwise use 0 - * - * Scan the device for the generic I2C properties describing timing parameters - * for the signal and fill the given struct with the results. If a property was - * not found and use_defaults was true, then maximum timings are assumed which - * are derived from the I2C specification. If use_defaults is not used, the - * results will be 0, so drivers can apply their own defaults later. The latter - * is mainly intended for avoiding regressions of existing drivers which want - * to switch to this function. New drivers almost always should use the defaults. - */ - -void i2c_parse_fw_timings(struct device *dev, struct i2c_timings *t, bool use_defaults) -{ - int ret; - - memset(t, 0, sizeof(*t)); - - ret = device_property_read_u32(dev, "clock-frequency", &t->bus_freq_hz); - if (ret && use_defaults) - t->bus_freq_hz = 100000; - - ret = device_property_read_u32(dev, "i2c-scl-rising-time-ns", &t->scl_rise_ns); - if (ret && use_defaults) { - if (t->bus_freq_hz <= 100000) - t->scl_rise_ns = 1000; - else if (t->bus_freq_hz <= 400000) - t->scl_rise_ns = 300; - else - t->scl_rise_ns = 120; - } - - ret = device_property_read_u32(dev, "i2c-scl-falling-time-ns", &t->scl_fall_ns); - if (ret && use_defaults) { - if (t->bus_freq_hz <= 400000) - t->scl_fall_ns = 300; - else - t->scl_fall_ns = 120; - } - - device_property_read_u32(dev, "i2c-scl-internal-delay-ns", &t->scl_int_delay_ns); - - ret = device_property_read_u32(dev, "i2c-sda-falling-time-ns", &t->sda_fall_ns); - if (ret && use_defaults) - t->sda_fall_ns = t->scl_fall_ns; -} -EXPORT_SYMBOL_GPL(i2c_parse_fw_timings); - static int of_dev_node_match(struct device *dev, void *data) { return dev->of_node == data; @@ -1892,6 +1840,58 @@ void i2c_del_adapter(struct i2c_adapter *adap) } EXPORT_SYMBOL(i2c_del_adapter); +/** + * i2c_parse_fw_timings - get I2C related timing parameters from firmware + * @dev: The device to scan for I2C timing properties + * @t: the i2c_timings struct to be filled with values + * @use_defaults: bool to use sane defaults derived from the I2C specification + * when properties are not found, otherwise use 0 + * + * Scan the device for the generic I2C properties describing timing parameters + * for the signal and fill the given struct with the results. If a property was + * not found and use_defaults was true, then maximum timings are assumed which + * are derived from the I2C specification. If use_defaults is not used, the + * results will be 0, so drivers can apply their own defaults later. The latter + * is mainly intended for avoiding regressions of existing drivers which want + * to switch to this function. New drivers almost always should use the defaults. + */ + +void i2c_parse_fw_timings(struct device *dev, struct i2c_timings *t, bool use_defaults) +{ + int ret; + + memset(t, 0, sizeof(*t)); + + ret = device_property_read_u32(dev, "clock-frequency", &t->bus_freq_hz); + if (ret && use_defaults) + t->bus_freq_hz = 100000; + + ret = device_property_read_u32(dev, "i2c-scl-rising-time-ns", &t->scl_rise_ns); + if (ret && use_defaults) { + if (t->bus_freq_hz <= 100000) + t->scl_rise_ns = 1000; + else if (t->bus_freq_hz <= 400000) + t->scl_rise_ns = 300; + else + t->scl_rise_ns = 120; + } + + ret = device_property_read_u32(dev, "i2c-scl-falling-time-ns", &t->scl_fall_ns); + if (ret && use_defaults) { + if (t->bus_freq_hz <= 400000) + t->scl_fall_ns = 300; + else + t->scl_fall_ns = 120; + } + + device_property_read_u32(dev, "i2c-scl-internal-delay-ns", &t->scl_int_delay_ns); + + ret = device_property_read_u32(dev, "i2c-sda-falling-time-ns", &t->sda_fall_ns); + if (ret && use_defaults) + t->sda_fall_ns = t->scl_fall_ns; +} +EXPORT_SYMBOL_GPL(i2c_parse_fw_timings); + /* ------------------------------------------------------------------------- */ int i2c_for_each_dev(void *data, int (*fn)(struct device *, void *))