From: Roger Quadros Date: Tue, 18 Jun 2013 16:04:44 +0000 (+0300) Subject: ARM: dts: omap4-panda: Add USB Host support X-Git-Url: https://git.karo-electronics.de/?a=commitdiff_plain;h=5bd2100ed2a76147ddec95499214eb606b799a22;p=linux-beck.git ARM: dts: omap4-panda: Add USB Host support Provide the RESET and Power regulators for the USB PHY, the USB Host port mode and the PHY device. Also provide pin multiplexer information for the USB host pins. HACK: The reset control need to be replaced with the proper gpio-controlled reset driver as soon it will be merged [1]. [1] http://thread.gmane.org/gmane.linux.drivers.devicetree/36830 Signed-off-by: Roger Quadros [benoit.cousson@linaro.org: Add disclaimer about the reset control inside changelog and code] Cc: Florian Vaussard Signed-off-by: Benoit Cousson --- diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi index 00cbaa51b74b..60fc62489b7a 100644 --- a/arch/arm/boot/dts/omap4-panda-common.dtsi +++ b/arch/arm/boot/dts/omap4-panda-common.dtsi @@ -59,6 +59,47 @@ "AFML", "Line In", "AFMR", "Line In"; }; + + /* + * Temp hack: Need to be replaced with the proper gpio-controlled + * reset driver as soon it will be merged. + * http://thread.gmane.org/gmane.linux.drivers.devicetree/36830 + */ + /* HS USB Port 1 RESET */ + hsusb1_reset: hsusb1_reset_reg { + compatible = "regulator-fixed"; + regulator-name = "hsusb1_reset"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 30 0>; /* gpio_62 */ + startup-delay-us = <70000>; + enable-active-high; + }; + + /* HS USB Port 1 Power */ + hsusb1_power: hsusb1_power_reg { + compatible = "regulator-fixed"; + regulator-name = "hsusb1_vbus"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio1 1 0>; /* gpio_1 */ + startup-delay-us = <70000>; + enable-active-high; + }; + + /* HS USB Host PHY on PORT 1 */ + hsusb1_phy: hsusb1_phy { + compatible = "usb-nop-xceiv"; + reset-supply = <&hsusb1_reset>; + vcc-supply = <&hsusb1_power>; + /** + * FIXME: + * put the right clock phandle here when available + * clocks = <&auxclk3>; + * clock-names = "main_clk"; + */ + clock-frequency = <19200000>; + }; }; &omap4_pmx_wkup { @@ -83,6 +124,7 @@ &mcbsp1_pins &dss_hdmi_pins &tpd12s015_pins + &hsusbb1_pins >; twl6030_pins: pinmux_twl6030_pins { @@ -133,6 +175,23 @@ >; }; + hsusbb1_pins: pinmux_hsusbb1_pins { + pinctrl-single,pins = < + 0x82 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_clk.usbb1_ulpiphy_clk */ + 0x84 (PIN_OUTPUT | MUX_MODE4) /* usbb1_ulpitll_stp.usbb1_ulpiphy_stp */ + 0x86 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dir.usbb1_ulpiphy_dir */ + 0x88 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_nxt.usbb1_ulpiphy_nxt */ + 0x8a (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat0.usbb1_ulpiphy_dat0 */ + 0x8c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat1.usbb1_ulpiphy_dat1 */ + 0x8e (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat2.usbb1_ulpiphy_dat2 */ + 0x90 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat3.usbb1_ulpiphy_dat3 */ + 0x92 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat4.usbb1_ulpiphy_dat4 */ + 0x94 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat5.usbb1_ulpiphy_dat5 */ + 0x96 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat6.usbb1_ulpiphy_dat6 */ + 0x98 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat7.usbb1_ulpiphy_dat7 */ + >; + }; + i2c1_pins: pinmux_i2c1_pins { pinctrl-single,pins = < 0xe2 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */ @@ -283,3 +342,11 @@ mode = <3>; power = <50>; }; + +&usbhshost { + port1-mode = "ehci-phy"; +}; + +&usbhsehci { + phys = <&hsusb1_phy>; +};