From: Ludovic Desroches Date: Thu, 11 Aug 2011 15:25:44 +0000 (+0000) Subject: mmc: atmel-mci: add pdc support and runtime capabilities detection X-Git-Url: https://git.karo-electronics.de/?a=commitdiff_plain;h=796211b7953;p=linux-beck.git mmc: atmel-mci: add pdc support and runtime capabilities detection Add pdc support for atmel-mci. It makes at91-mci driver useless because it was only used for the old atmel MCI core which has pdc but no dma support. To allow removing at91-mci, the capabilities of the MCI core are detected at runtime -- then the driver will use pio, pdc or dma transfers. Warning: at91rm9200 is not supported, to support it we need to use swab32 on data but I have no board to test it. Signed-off-by: Ludovic Desroches Signed-off-by: Nicolas Ferre Signed-off-by: Chris Ball --- diff --git a/drivers/mmc/host/atmel-mci-regs.h b/drivers/mmc/host/atmel-mci-regs.h index 7310b207a442..000b3ad0f5ca 100644 --- a/drivers/mmc/host/atmel-mci-regs.h +++ b/drivers/mmc/host/atmel-mci-regs.h @@ -88,8 +88,14 @@ # define ATMCI_BLKE ( 1 << 3) /* Data Block Ended */ # define ATMCI_DTIP ( 1 << 4) /* Data Transfer In Progress */ # define ATMCI_NOTBUSY ( 1 << 5) /* Data Not Busy */ +# define ATMCI_ENDRX ( 1 << 6) /* End of RX Buffer */ +# define ATMCI_ENDTX ( 1 << 7) /* End of TX Buffer */ # define ATMCI_SDIOIRQA ( 1 << 8) /* SDIO IRQ in slot A */ # define ATMCI_SDIOIRQB ( 1 << 9) /* SDIO IRQ in slot B */ +# define ATMCI_SDIOWAIT ( 1 << 12) /* SDIO Read Wait Operation Status */ +# define ATMCI_CSRCV ( 1 << 13) /* CE-ATA Completion Signal Received */ +# define ATMCI_RXBUFF ( 1 << 14) /* RX Buffer Full */ +# define ATMCI_TXBUFE ( 1 << 15) /* TX Buffer Empty */ # define ATMCI_RINDE ( 1 << 16) /* Response Index Error */ # define ATMCI_RDIRE ( 1 << 17) /* Response Direction Error */ # define ATMCI_RCRCE ( 1 << 18) /* Response CRC Error */ @@ -97,6 +103,13 @@ # define ATMCI_RTOE ( 1 << 20) /* Response Time-Out Error */ # define ATMCI_DCRCE ( 1 << 21) /* Data CRC Error */ # define ATMCI_DTOE ( 1 << 22) /* Data Time-Out Error */ +# define ATMCI_CSTOE ( 1 << 23) /* Completion Signal Time-out Error */ +# define ATMCI_BLKOVRE ( 1 << 24) /* DMA Block Overrun Error */ +# define ATMCI_DMADONE ( 1 << 25) /* DMA Transfer Done */ +# define ATMCI_FIFOEMPTY ( 1 << 26) /* FIFO Empty Flag */ +# define ATMCI_XFRDONE ( 1 << 27) /* Transfer Done Flag */ +# define ATMCI_ACKRCV ( 1 << 28) /* Boot Operation Acknowledge Received */ +# define ATMCI_ACKRCVE ( 1 << 29) /* Boot Operation Acknowledge Error */ # define ATMCI_OVRE ( 1 << 30) /* RX Overrun Error */ # define ATMCI_UNRE ( 1 << 31) /* TX Underrun Error */ #define ATMCI_DMA 0x0050 /* DMA Configuration[2] */ @@ -114,6 +127,7 @@ #define ATMCI_WPSR 0x00e8 /* Write Protection Status[2] */ # define ATMCI_GET_WP_VS(x) ((x) & 0x0f) # define ATMCI_GET_WP_VSRC(x) (((x) >> 8) & 0xffff) +#define ATMCI_VERSION 0x00FC /* Version */ #define ATMCI_FIFO_APERTURE 0x0200 /* FIFO Aperture[2] */ /* This is not including the FIFO Aperture on MCI2 */ diff --git a/drivers/mmc/host/atmel-mci.c b/drivers/mmc/host/atmel-mci.c index 87eeccc6d9a4..57596782061b 100644 --- a/drivers/mmc/host/atmel-mci.c +++ b/drivers/mmc/host/atmel-mci.c @@ -30,6 +30,7 @@ #include #include +#include #include #include @@ -58,18 +59,35 @@ enum atmel_mci_state { STATE_DATA_ERROR, }; +enum atmci_xfer_dir { + XFER_RECEIVE = 0, + XFER_TRANSMIT, +}; + +enum atmci_pdc_buf { + PDC_FIRST_BUF = 0, + PDC_SECOND_BUF, +}; + +struct atmel_mci_caps { + bool has_dma; + bool has_pdc; + bool has_cfg_reg; + bool has_cstor_reg; + bool has_highspeed; + bool has_rwproof; +}; + struct atmel_mci_dma { -#ifdef CONFIG_MMC_ATMELMCI_DMA struct dma_chan *chan; struct dma_async_tx_descriptor *data_desc; -#endif }; /** * struct atmel_mci - MMC controller state shared between all slots * @lock: Spinlock protecting the queue and associated data. * @regs: Pointer to MMIO registers. - * @sg: Scatterlist entry currently being processed by PIO code, if any. + * @sg: Scatterlist entry currently being processed by PIO or PDC code. * @pio_offset: Offset into the current scatterlist entry. * @cur_slot: The slot which is currently using the controller. * @mrq: The request currently being processed on @cur_slot, @@ -77,6 +95,7 @@ struct atmel_mci_dma { * @cmd: The command currently being sent to the card, or NULL. * @data: The data currently being transferred, or NULL if no data * transfer is in progress. + * @data_size: just data->blocks * data->blksz. * @dma: DMA client state. * @data_chan: DMA channel being used for the current data transfer. * @cmd_status: Snapshot of SR taken upon completion of the current @@ -103,6 +122,13 @@ struct atmel_mci_dma { * @mck: The peripheral bus clock hooked up to the MMC controller. * @pdev: Platform device associated with the MMC controller. * @slot: Slots sharing this MMC controller. + * @caps: MCI capabilities depending on MCI version. + * @prepare_data: function to setup MCI before data transfer which + * depends on MCI capabilities. + * @submit_data: function to start data transfer which depends on MCI + * capabilities. + * @stop_transfer: function to stop data transfer which depends on MCI + * capabilities. * * Locking * ======= @@ -143,6 +169,7 @@ struct atmel_mci { struct mmc_request *mrq; struct mmc_command *cmd; struct mmc_data *data; + unsigned int data_size; struct atmel_mci_dma dma; struct dma_chan *data_chan; @@ -167,6 +194,12 @@ struct atmel_mci { struct platform_device *pdev; struct atmel_mci_slot *slot[ATMCI_MAX_NR_SLOTS]; + + struct atmel_mci_caps caps; + + u32 (*prepare_data)(struct atmel_mci *host, struct mmc_data *data); + void (*submit_data)(struct atmel_mci *host, struct mmc_data *data); + void (*stop_transfer)(struct atmel_mci *host); }; /** @@ -219,31 +252,6 @@ struct atmel_mci_slot { #define atmci_set_pending(host, event) \ set_bit(event, &host->pending_events) -/* - * Enable or disable features/registers based on - * whether the processor supports them - */ -static bool atmci_has_rwproof(void) -{ - if (cpu_is_at91sam9261() || cpu_is_at91rm9200()) - return false; - else - return true; -} - -/* - * The new MCI2 module isn't 100% compatible with the old MCI module, - * and it has a few nice features which we want to use... - */ -static inline bool atmci_is_mci2(void) -{ - if (cpu_is_at91sam9g45()) - return true; - - return false; -} - - /* * The debugfs stuff below is mostly optimized away when * CONFIG_DEBUG_FS is not set. @@ -379,7 +387,7 @@ static int atmci_regs_show(struct seq_file *s, void *v) buf[ATMCI_BLKR / 4], buf[ATMCI_BLKR / 4] & 0xffff, (buf[ATMCI_BLKR / 4] >> 16) & 0xffff); - if (atmci_is_mci2()) + if (host->caps.has_cstor_reg) seq_printf(s, "CSTOR:\t0x%08x\n", buf[ATMCI_CSTOR / 4]); /* Don't read RSPR and RDR; it will consume the data there */ @@ -387,7 +395,7 @@ static int atmci_regs_show(struct seq_file *s, void *v) atmci_show_status_reg(s, "SR", buf[ATMCI_SR / 4]); atmci_show_status_reg(s, "IMR", buf[ATMCI_IMR / 4]); - if (atmci_is_mci2()) { + if (host->caps.has_dma) { u32 val; val = buf[ATMCI_DMA / 4]; @@ -396,6 +404,9 @@ static int atmci_regs_show(struct seq_file *s, void *v) ((val >> 4) & 3) ? 1 << (((val >> 4) & 3) + 1) : 1, val & ATMCI_DMAEN ? " DMAEN" : ""); + } + if (host->caps.has_cfg_reg) { + u32 val; val = buf[ATMCI_CFG / 4]; seq_printf(s, "CFG:\t0x%08x%s%s%s%s\n", @@ -574,33 +585,109 @@ static void atmci_send_stop_cmd(struct atmel_mci *host, struct mmc_data *data) atmci_writel(host, ATMCI_IER, ATMCI_CMDRDY); } -#ifdef CONFIG_MMC_ATMELMCI_DMA -static void atmci_dma_cleanup(struct atmel_mci *host) +/* + * Configure given PDC buffer taking care of alignement issues. + * Update host->data_size and host->sg. + */ +static void atmci_pdc_set_single_buf(struct atmel_mci *host, + enum atmci_xfer_dir dir, enum atmci_pdc_buf buf_nb) { - struct mmc_data *data = host->data; + u32 pointer_reg, counter_reg; + + if (dir == XFER_RECEIVE) { + pointer_reg = ATMEL_PDC_RPR; + counter_reg = ATMEL_PDC_RCR; + } else { + pointer_reg = ATMEL_PDC_TPR; + counter_reg = ATMEL_PDC_TCR; + } + + if (buf_nb == PDC_SECOND_BUF) { + pointer_reg += 0x10; + counter_reg += 0x10; + } + + atmci_writel(host, pointer_reg, sg_dma_address(host->sg)); + if (host->data_size <= PAGE_SIZE) { + if (host->data_size & 0x3) { + /* If size is different from modulo 4, transfer bytes */ + atmci_writel(host, counter_reg, host->data_size); + atmci_writel(host, ATMCI_MR, host->mode_reg | ATMCI_MR_PDCFBYTE); + } else { + /* Else transfer 32-bits words */ + atmci_writel(host, counter_reg, host->data_size / 4); + } + host->data_size = 0; + } else { + /* We assume the size of a page is 32-bits aligned */ + atmci_writel(host, counter_reg, PAGE_SIZE / 4); + host->data_size -= PAGE_SIZE; + if (host->data_size) + host->sg = sg_next(host->sg); + } +} + +/* + * Configure PDC buffer according to the data size ie configuring one or two + * buffers. Don't use this function if you want to configure only the second + * buffer. In this case, use atmci_pdc_set_single_buf. + */ +static void atmci_pdc_set_both_buf(struct atmel_mci *host, int dir) +{ + atmci_pdc_set_single_buf(host, dir, PDC_FIRST_BUF); + if (host->data_size) + atmci_pdc_set_single_buf(host, dir, PDC_SECOND_BUF); +} + +/* + * Unmap sg lists, called when transfer is finished. + */ +static void atmci_pdc_cleanup(struct atmel_mci *host) +{ + struct mmc_data *data = host->data; if (data) - dma_unmap_sg(host->dma.chan->device->dev, - data->sg, data->sg_len, - ((data->flags & MMC_DATA_WRITE) - ? DMA_TO_DEVICE : DMA_FROM_DEVICE)); + dma_unmap_sg(&host->pdev->dev, + data->sg, data->sg_len, + ((data->flags & MMC_DATA_WRITE) + ? DMA_TO_DEVICE : DMA_FROM_DEVICE)); } -static void atmci_stop_dma(struct atmel_mci *host) +/* + * Disable PDC transfers. Update pending flags to EVENT_XFER_COMPLETE after + * having received ATMCI_TXBUFE or ATMCI_RXBUFF interrupt. Enable ATMCI_NOTBUSY + * interrupt needed for both transfer directions. + */ +static void atmci_pdc_complete(struct atmel_mci *host) { - struct dma_chan *chan = host->data_chan; + atmci_writel(host, ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS | ATMEL_PDC_TXTDIS); + atmci_pdc_cleanup(host); - if (chan) { - dmaengine_terminate_all(chan); - atmci_dma_cleanup(host); - } else { - /* Data transfer was stopped by the interrupt handler */ + /* + * If the card was removed, data will be NULL. No point trying + * to send the stop command or waiting for NBUSY in this case. + */ + if (host->data) { atmci_set_pending(host, EVENT_XFER_COMPLETE); + tasklet_schedule(&host->tasklet); atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY); } } -/* This function is called by the DMA driver from tasklet context. */ +static void atmci_dma_cleanup(struct atmel_mci *host) +{ + struct mmc_data *data = host->data; + + if (data) + dma_unmap_sg(host->dma.chan->device->dev, + data->sg, data->sg_len, + ((data->flags & MMC_DATA_WRITE) + ? DMA_TO_DEVICE : DMA_FROM_DEVICE)); +} + +/* + * This function is called by the DMA driver from tasklet context. + */ static void atmci_dma_complete(void *arg) { struct atmel_mci *host = arg; @@ -608,7 +695,7 @@ static void atmci_dma_complete(void *arg) dev_vdbg(&host->pdev->dev, "DMA complete\n"); - if (atmci_is_mci2()) + if (host->caps.has_dma) /* Disable DMA hardware handshaking on MCI */ atmci_writel(host, ATMCI_DMA, atmci_readl(host, ATMCI_DMA) & ~ATMCI_DMAEN); @@ -646,7 +733,90 @@ static void atmci_dma_complete(void *arg) } } -static int +/* + * Returns a mask of interrupt flags to be enabled after the whole + * request has been prepared. + */ +static u32 atmci_prepare_data(struct atmel_mci *host, struct mmc_data *data) +{ + u32 iflags; + + data->error = -EINPROGRESS; + + host->sg = data->sg; + host->data = data; + host->data_chan = NULL; + + iflags = ATMCI_DATA_ERROR_FLAGS; + + /* + * Errata: MMC data write operation with less than 12 + * bytes is impossible. + * + * Errata: MCI Transmit Data Register (TDR) FIFO + * corruption when length is not multiple of 4. + */ + if (data->blocks * data->blksz < 12 + || (data->blocks * data->blksz) & 3) + host->need_reset = true; + + host->pio_offset = 0; + if (data->flags & MMC_DATA_READ) + iflags |= ATMCI_RXRDY; + else + iflags |= ATMCI_TXRDY; + + return iflags; +} + +/* + * Set interrupt flags and set block length into the MCI mode register even + * if this value is also accessible in the MCI block register. It seems to be + * necessary before the High Speed MCI version. It also map sg and configure + * PDC registers. + */ +static u32 +atmci_prepare_data_pdc(struct atmel_mci *host, struct mmc_data *data) +{ + u32 iflags, tmp; + unsigned int sg_len; + enum dma_data_direction dir; + + data->error = -EINPROGRESS; + + host->data = data; + host->sg = data->sg; + iflags = ATMCI_DATA_ERROR_FLAGS; + + /* Enable pdc mode */ + atmci_writel(host, ATMCI_MR, host->mode_reg | ATMCI_MR_PDCMODE); + + if (data->flags & MMC_DATA_READ) { + dir = DMA_FROM_DEVICE; + iflags |= ATMCI_ENDRX | ATMCI_RXBUFF; + } else { + dir = DMA_TO_DEVICE; + iflags |= ATMCI_ENDTX | ATMCI_TXBUFE; + } + + /* Set BLKLEN */ + tmp = atmci_readl(host, ATMCI_MR); + tmp &= 0x0000ffff; + tmp |= ATMCI_BLKLEN(data->blksz); + atmci_writel(host, ATMCI_MR, tmp); + + /* Configure PDC */ + host->data_size = data->blocks * data->blksz; + sg_len = dma_map_sg(&host->pdev->dev, data->sg, data->sg_len, dir); + BUG_ON(sg_len < host->data_size / PAGE_SIZE); + if (host->data_size) + atmci_pdc_set_both_buf(host, + ((dir == DMA_FROM_DEVICE) ? XFER_RECEIVE : XFER_TRANSMIT)); + + return iflags; +} + +static u32 atmci_prepare_data_dma(struct atmel_mci *host, struct mmc_data *data) { struct dma_chan *chan; @@ -655,20 +825,29 @@ atmci_prepare_data_dma(struct atmel_mci *host, struct mmc_data *data) unsigned int i; enum dma_data_direction direction; unsigned int sglen; + u32 iflags; + + data->error = -EINPROGRESS; + + WARN_ON(host->data); + host->sg = NULL; + host->data = data; + + iflags = ATMCI_DATA_ERROR_FLAGS; /* * We don't do DMA on "complex" transfers, i.e. with * non-word-aligned buffers or lengths. Also, we don't bother * with all the DMA setup overhead for short transfers. */ - if (data->blocks * data->blksz < ATATMCI_DMA_THRESHOLD) - return -EINVAL; + if (data->blocks * data->blksz < ATMCI_DMA_THRESHOLD) + return atmci_prepare_data(host, data); if (data->blksz & 3) - return -EINVAL; + return atmci_prepare_data(host, data); for_each_sg(data->sg, sg, data->sg_len, i) { if (sg->offset & 3 || sg->length & 3) - return -EINVAL; + return atmci_prepare_data(host, data); } /* If we don't have a channel, we can't do DMA */ @@ -679,7 +858,7 @@ atmci_prepare_data_dma(struct atmel_mci *host, struct mmc_data *data) if (!chan) return -ENODEV; - if (atmci_is_mci2()) + if (host->caps.has_dma) atmci_writel(host, ATMCI_DMA, ATMCI_DMA_CHKSIZE(3) | ATMCI_DMAEN); if (data->flags & MMC_DATA_READ) @@ -688,7 +867,7 @@ atmci_prepare_data_dma(struct atmel_mci *host, struct mmc_data *data) direction = DMA_TO_DEVICE; sglen = dma_map_sg(chan->device->dev, data->sg, - data->sg_len, direction); + data->sg_len, direction); desc = chan->device->device_prep_slave_sg(chan, data->sg, sglen, direction, @@ -700,13 +879,32 @@ atmci_prepare_data_dma(struct atmel_mci *host, struct mmc_data *data) desc->callback = atmci_dma_complete; desc->callback_param = host; - return 0; + return iflags; unmap_exit: dma_unmap_sg(chan->device->dev, data->sg, data->sg_len, direction); return -ENOMEM; } -static void atmci_submit_data(struct atmel_mci *host) +static void +atmci_submit_data(struct atmel_mci *host, struct mmc_data *data) +{ + return; +} + +/* + * Start PDC according to transfer direction. + */ +static void +atmci_submit_data_pdc(struct atmel_mci *host, struct mmc_data *data) +{ + if (data->flags & MMC_DATA_READ) + atmci_writel(host, ATMEL_PDC_PTCR, ATMEL_PDC_RXTEN); + else + atmci_writel(host, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN); +} + +static void +atmci_submit_data_dma(struct atmel_mci *host, struct mmc_data *data) { struct dma_chan *chan = host->data_chan; struct dma_async_tx_descriptor *desc = host->dma.data_desc; @@ -717,64 +915,39 @@ static void atmci_submit_data(struct atmel_mci *host) } } -#else /* CONFIG_MMC_ATMELMCI_DMA */ - -static int atmci_prepare_data_dma(struct atmel_mci *host, struct mmc_data *data) +static void atmci_stop_transfer(struct atmel_mci *host) { - return -ENOSYS; -} - -static void atmci_submit_data(struct atmel_mci *host) {} - -static void atmci_stop_dma(struct atmel_mci *host) -{ - /* Data transfer was stopped by the interrupt handler */ atmci_set_pending(host, EVENT_XFER_COMPLETE); atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY); } -#endif /* CONFIG_MMC_ATMELMCI_DMA */ - /* - * Returns a mask of interrupt flags to be enabled after the whole - * request has been prepared. + * Stop data transfer because error(s) occured. */ -static u32 atmci_prepare_data(struct atmel_mci *host, struct mmc_data *data) +static void atmci_stop_transfer_pdc(struct atmel_mci *host) { - u32 iflags; - - data->error = -EINPROGRESS; - - WARN_ON(host->data); - host->sg = NULL; - host->data = data; - - iflags = ATMCI_DATA_ERROR_FLAGS; - if (atmci_prepare_data_dma(host, data)) { - host->data_chan = NULL; + atmci_set_pending(host, EVENT_XFER_COMPLETE); + atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY); +} - /* - * Errata: MMC data write operation with less than 12 - * bytes is impossible. - * - * Errata: MCI Transmit Data Register (TDR) FIFO - * corruption when length is not multiple of 4. - */ - if (data->blocks * data->blksz < 12 - || (data->blocks * data->blksz) & 3) - host->need_reset = true; +static void atmci_stop_transfer_dma(struct atmel_mci *host) +{ + struct dma_chan *chan = host->data_chan; - host->sg = data->sg; - host->pio_offset = 0; - if (data->flags & MMC_DATA_READ) - iflags |= ATMCI_RXRDY; - else - iflags |= ATMCI_TXRDY; + if (chan) { + dmaengine_terminate_all(chan); + atmci_dma_cleanup(host); + } else { + /* Data transfer was stopped by the interrupt handler */ + atmci_set_pending(host, EVENT_XFER_COMPLETE); + atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY); } - - return iflags; } +/* + * Start a request: prepare data if needed, prepare the command and activate + * interrupts. + */ static void atmci_start_request(struct atmel_mci *host, struct atmel_mci_slot *slot) { @@ -796,7 +969,7 @@ static void atmci_start_request(struct atmel_mci *host, atmci_writel(host, ATMCI_CR, ATMCI_CR_SWRST); atmci_writel(host, ATMCI_CR, ATMCI_CR_MCIEN); atmci_writel(host, ATMCI_MR, host->mode_reg); - if (atmci_is_mci2()) + if (host->caps.has_cfg_reg) atmci_writel(host, ATMCI_CFG, host->cfg_reg); host->need_reset = false; } @@ -824,7 +997,7 @@ static void atmci_start_request(struct atmel_mci *host, dev_vdbg(&slot->mmc->class_dev, "BLKR=0x%08x\n", ATMCI_BCNT(data->blocks) | ATMCI_BLKLEN(data->blksz)); - iflags |= atmci_prepare_data(host, data); + iflags |= host->prepare_data(host, data); } iflags |= ATMCI_CMDRDY; @@ -833,7 +1006,7 @@ static void atmci_start_request(struct atmel_mci *host, atmci_start_command(host, cmd, cmdflags); if (data) - atmci_submit_data(host); + host->submit_data(host, data); if (mrq->stop) { host->stop_cmdr = atmci_prepare_command(slot->mmc, mrq->stop); @@ -929,7 +1102,7 @@ static void atmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) clk_enable(host->mck); atmci_writel(host, ATMCI_CR, ATMCI_CR_SWRST); atmci_writel(host, ATMCI_CR, ATMCI_CR_MCIEN); - if (atmci_is_mci2()) + if (host->caps.has_cfg_reg) atmci_writel(host, ATMCI_CFG, host->cfg_reg); } @@ -960,10 +1133,10 @@ static void atmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) * stopping the clock when the FIFO is full/empty. * This state is not expected to last for long. */ - if (atmci_has_rwproof()) + if (host->caps.has_rwproof) host->mode_reg |= (ATMCI_MR_WRPROOF | ATMCI_MR_RDPROOF); - if (atmci_is_mci2()) { + if (host->caps.has_cfg_reg) { /* setup High Speed mode in relation with card capacity */ if (ios->timing == MMC_TIMING_SD_HS) host->cfg_reg |= ATMCI_CFG_HSMODE; @@ -973,7 +1146,7 @@ static void atmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) if (list_empty(&host->queue)) { atmci_writel(host, ATMCI_MR, host->mode_reg); - if (atmci_is_mci2()) + if (host->caps.has_cfg_reg) atmci_writel(host, ATMCI_CFG, host->cfg_reg); } else { host->need_clock_update = true; @@ -1088,7 +1261,7 @@ static void atmci_request_end(struct atmel_mci *host, struct mmc_request *mrq) */ if (host->need_clock_update) { atmci_writel(host, ATMCI_MR, host->mode_reg); - if (atmci_is_mci2()) + if (host->caps.has_cfg_reg) atmci_writel(host, ATMCI_CFG, host->cfg_reg); } @@ -1137,7 +1310,7 @@ static void atmci_command_complete(struct atmel_mci *host, "command error: status=0x%08x\n", status); if (cmd->data) { - atmci_stop_dma(host); + host->stop_transfer(host); host->data = NULL; atmci_writel(host, ATMCI_IDR, ATMCI_NOTBUSY | ATMCI_TXRDY | ATMCI_RXRDY @@ -1195,7 +1368,7 @@ static void atmci_detect_change(unsigned long data) atmci_writel(host, ATMCI_CR, ATMCI_CR_SWRST); atmci_writel(host, ATMCI_CR, ATMCI_CR_MCIEN); atmci_writel(host, ATMCI_MR, host->mode_reg); - if (atmci_is_mci2()) + if (host->caps.has_cfg_reg) atmci_writel(host, ATMCI_CFG, host->cfg_reg); host->data = NULL; @@ -1211,7 +1384,7 @@ static void atmci_detect_change(unsigned long data) /* fall through */ case STATE_SENDING_DATA: mrq->data->error = -ENOMEDIUM; - atmci_stop_dma(host); + host->stop_transfer(host); break; case STATE_DATA_BUSY: case STATE_DATA_ERROR: @@ -1290,7 +1463,7 @@ static void atmci_tasklet_func(unsigned long priv) case STATE_SENDING_DATA: if (atmci_test_and_clear_pending(host, EVENT_DATA_ERROR)) { - atmci_stop_dma(host); + host->stop_transfer(host); if (data->stop) atmci_send_stop_cmd(host, data); state = STATE_DATA_ERROR; @@ -1556,6 +1729,56 @@ static irqreturn_t atmci_interrupt(int irq, void *dev_id) atmci_set_pending(host, EVENT_DATA_ERROR); tasklet_schedule(&host->tasklet); } + + if (pending & ATMCI_ENDTX) { + atmci_writel(host, ATMCI_IDR, ATMCI_ENDTX); + if (host->data_size) { + atmci_pdc_set_single_buf(host, + XFER_TRANSMIT, PDC_SECOND_BUF); + atmci_writel(host, ATMCI_IER, ATMCI_ENDTX); + } + } + + if (pending & ATMCI_TXBUFE) { + atmci_writel(host, ATMCI_IDR, ATMCI_TXBUFE); + /* + * We can receive this interruption before having configured + * the second pdc buffer, so we need to reconfigure first and + * second buffers again + */ + if (host->data_size) { + atmci_pdc_set_both_buf(host, XFER_TRANSMIT); + atmci_writel(host, ATMCI_IER, ATMCI_TXBUFE); + } else { + atmci_pdc_complete(host); + } + } + + if (pending & ATMCI_ENDRX) { + atmci_writel(host, ATMCI_IDR, ATMCI_ENDRX); + + if (host->data_size) { + atmci_pdc_set_single_buf(host, + XFER_RECEIVE, PDC_SECOND_BUF); + atmci_writel(host, ATMCI_IER, ATMCI_ENDRX); + } + } + + if (pending & ATMCI_RXBUFF) { + atmci_writel(host, ATMCI_IDR, ATMCI_RXBUFF); + /* + * We can receive this interruption before having configured + * the second pdc buffer, so we need to reconfigure first and + * second buffers again + */ + if (host->data_size) { + atmci_pdc_set_both_buf(host, XFER_RECEIVE); + atmci_writel(host, ATMCI_IER, ATMCI_RXBUFF); + } else { + atmci_pdc_complete(host); + } + } + if (pending & ATMCI_NOTBUSY) { atmci_writel(host, ATMCI_IDR, ATMCI_DATA_ERROR_FLAGS | ATMCI_NOTBUSY); @@ -1622,7 +1845,7 @@ static int __init atmci_init_slot(struct atmel_mci *host, mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34; if (sdio_irq) mmc->caps |= MMC_CAP_SDIO_IRQ; - if (atmci_is_mci2()) + if (host->caps.has_highspeed) mmc->caps |= MMC_CAP_SD_HIGHSPEED; if (slot_data->bus_width >= 4) mmc->caps |= MMC_CAP_4_BIT_DATA; @@ -1705,7 +1928,6 @@ static void __exit atmci_cleanup_slot(struct atmel_mci_slot *slot, mmc_free_host(slot->mmc); } -#ifdef CONFIG_MMC_ATMELMCI_DMA static bool atmci_filter(struct dma_chan *chan, void *slave) { struct mci_dma_data *sl = slave; @@ -1747,9 +1969,60 @@ static void atmci_configure_dma(struct atmel_mci *host) "Using %s for DMA transfers\n", dma_chan_name(host->dma.chan)); } + +static inline unsigned int atmci_get_version(struct atmel_mci *host) +{ + return atmci_readl(host, ATMCI_VERSION) & 0x00000fff; +} + +/* + * HSMCI (High Speed MCI) module is not fully compatible with MCI module. + * HSMCI provides DMA support and a new config register but no more supports + * PDC. + */ +static void __init atmci_get_cap(struct atmel_mci *host) +{ + unsigned int version; + + version = atmci_get_version(host); + dev_info(&host->pdev->dev, + "version: 0x%x\n", version); + + host->caps.has_dma = 0; + host->caps.has_pdc = 0; + host->caps.has_cfg_reg = 0; + host->caps.has_cstor_reg = 0; + host->caps.has_highspeed = 0; + host->caps.has_rwproof = 0; + + /* keep only major version number */ + switch (version & 0xf00) { + case 0x100: + case 0x200: + host->caps.has_pdc = 1; + host->caps.has_rwproof = 1; + break; + case 0x300: + case 0x400: + case 0x500: +#ifdef CONFIG_AT_HDMAC + host->caps.has_dma = 1; #else -static void atmci_configure_dma(struct atmel_mci *host) {} + host->caps.has_dma = 0; + dev_info(&host->pdev->dev, + "has dma capability but dma engine is not selected, then use pio\n"); #endif + host->caps.has_cfg_reg = 1; + host->caps.has_cstor_reg = 1; + host->caps.has_highspeed = 1; + host->caps.has_rwproof = 1; + break; + default: + dev_warn(&host->pdev->dev, + "Unmanaged mci version, set minimum capabilities\n"); + break; + } +} static int __init atmci_probe(struct platform_device *pdev) { @@ -1802,7 +2075,27 @@ static int __init atmci_probe(struct platform_device *pdev) if (ret) goto err_request_irq; - atmci_configure_dma(host); + /* Get MCI capabilities and set operations according to it */ + atmci_get_cap(host); + if (host->caps.has_dma) { + dev_info(&pdev->dev, "using DMA\n"); + host->prepare_data = &atmci_prepare_data_dma; + host->submit_data = &atmci_submit_data_dma; + host->stop_transfer = &atmci_stop_transfer_dma; + } else if (host->caps.has_pdc) { + dev_info(&pdev->dev, "using PDC\n"); + host->prepare_data = &atmci_prepare_data_pdc; + host->submit_data = &atmci_submit_data_pdc; + host->stop_transfer = &atmci_stop_transfer_pdc; + } else { + dev_info(&pdev->dev, "no DMA, no PDC\n"); + host->prepare_data = &atmci_prepare_data; + host->submit_data = &atmci_submit_data; + host->stop_transfer = &atmci_stop_transfer; + } + + if (host->caps.has_dma) + atmci_configure_dma(host); platform_set_drvdata(pdev, host); @@ -1834,10 +2127,8 @@ static int __init atmci_probe(struct platform_device *pdev) return 0; err_init_slot: -#ifdef CONFIG_MMC_ATMELMCI_DMA if (host->dma.chan) dma_release_channel(host->dma.chan); -#endif free_irq(irq, host); err_request_irq: iounmap(host->regs);