From: Mike Sinkovsky Date: Wed, 4 Apr 2012 19:33:53 +0000 (+0000) Subject: Ethernet driver for the WIZnet W5300 chip X-Git-Url: https://git.karo-electronics.de/?a=commitdiff_plain;h=9899b81e7ca5c285b825ff10ca9357dd18813d83;p=linux-beck.git Ethernet driver for the WIZnet W5300 chip Based on original driver from chip manufacturer, but nearly full rewite. Tested and used in production with Blackfin BF531 embedded processor. Signed-off-by: Mike Sinkovsky Signed-off-by: David S. Miller --- diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig index c63a64cb6085..a11af5cc4844 100644 --- a/drivers/net/ethernet/Kconfig +++ b/drivers/net/ethernet/Kconfig @@ -174,6 +174,7 @@ source "drivers/net/ethernet/tile/Kconfig" source "drivers/net/ethernet/toshiba/Kconfig" source "drivers/net/ethernet/tundra/Kconfig" source "drivers/net/ethernet/via/Kconfig" +source "drivers/net/ethernet/wiznet/Kconfig" source "drivers/net/ethernet/xilinx/Kconfig" source "drivers/net/ethernet/xircom/Kconfig" diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile index 9676a5109d94..878ad32b93f2 100644 --- a/drivers/net/ethernet/Makefile +++ b/drivers/net/ethernet/Makefile @@ -73,5 +73,6 @@ obj-$(CONFIG_TILE_NET) += tile/ obj-$(CONFIG_NET_VENDOR_TOSHIBA) += toshiba/ obj-$(CONFIG_NET_VENDOR_TUNDRA) += tundra/ obj-$(CONFIG_NET_VENDOR_VIA) += via/ +obj-$(CONFIG_NET_VENDOR_WIZNET) += wiznet/ obj-$(CONFIG_NET_VENDOR_XILINX) += xilinx/ obj-$(CONFIG_NET_VENDOR_XIRCOM) += xircom/ diff --git a/drivers/net/ethernet/wiznet/Kconfig b/drivers/net/ethernet/wiznet/Kconfig new file mode 100644 index 000000000000..f45cef16bfda --- /dev/null +++ b/drivers/net/ethernet/wiznet/Kconfig @@ -0,0 +1,65 @@ +# +# WIZnet devices configuration +# + +config NET_VENDOR_WIZNET + bool "WIZnet devices" + default y + ---help--- + If you have a network (Ethernet) card belonging to this class, say Y + and read the Ethernet-HOWTO, available from + . + + Note that the answer to this question doesn't directly affect the + kernel: saying N will just cause the configurator to skip all + the questions about WIZnet devices. If you say Y, you will be asked + for your specific card in the following questions. + +if NET_VENDOR_WIZNET + +config WIZNET_W5300 + tristate "WIZnet W5300 Ethernet support" + ---help--- + Support for WIZnet W5300 chips. + + W5300 is a single chip with integrated 10/100 Ethernet MAC, + PHY and hardware TCP/IP stack, but this driver is limited to + the MAC and PHY functions only, onchip TCP/IP is unused. + + To compile this driver as a module, choose M here: the module + will be called w5300. + +choice + prompt "WIZnet interface mode" + default WIZNET_BUS_ANY + +config WIZNET_BUS_DIRECT + bool "Direct address bus mode" + ---help--- + In direct address mode host system can directly access all registers + after mapping to Memory-Mapped I/O space. + +config WIZNET_BUS_INDIRECT + bool "Indirect address bus mode" + ---help--- + In indirect address mode host system indirectly accesses registers + using Indirect Mode Address Register and Indirect Mode Data Register, + which are directly mapped to Memory-Mapped I/O space. + +config WIZNET_BUS_ANY + bool "Select interface mode in runtime" + ---help--- + If interface mode is unknown in compile time, it can be selected + in runtime from board/platform resources configuration. + + Performance may decrease compared to explicitly selected bus mode. +endchoice + +config WIZNET_TX_FLOW + bool "Use transmit flow control" + default y + help + This enables transmit flow control for WIZnet chips. + If unsure, say Y. + +endif # NET_VENDOR_WIZNET diff --git a/drivers/net/ethernet/wiznet/Makefile b/drivers/net/ethernet/wiznet/Makefile new file mode 100644 index 000000000000..88e0a3e62ba7 --- /dev/null +++ b/drivers/net/ethernet/wiznet/Makefile @@ -0,0 +1 @@ +obj-$(CONFIG_WIZNET_W5300) += w5300.o diff --git a/drivers/net/ethernet/wiznet/w5300.c b/drivers/net/ethernet/wiznet/w5300.c new file mode 100644 index 000000000000..88afde99de8d --- /dev/null +++ b/drivers/net/ethernet/wiznet/w5300.c @@ -0,0 +1,722 @@ +/* + * Ethernet driver for the WIZnet W5300 chip. + * + * Copyright (C) 2008-2009 WIZnet Co.,Ltd. + * Copyright (C) 2011 Taehun Kim gmail.com> + * Copyright (C) 2012 Mike Sinkovsky + * + * Licensed under the GPL-2 or later. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define DRV_NAME "w5300" +#define DRV_VERSION "2012-04-04" + +MODULE_DESCRIPTION("WIZnet W5300 Ethernet driver v"DRV_VERSION); +MODULE_AUTHOR("Mike Sinkovsky "); +MODULE_ALIAS("platform:"DRV_NAME); +MODULE_LICENSE("GPL"); + +/* + * Registers + */ +#define W5300_MR 0x0000 /* Mode Register */ +#define MR_DBW (1 << 15) /* Data bus width */ +#define MR_MPF (1 << 14) /* Mac layer pause frame */ +#define MR_WDF(n) (((n)&7)<<11) /* Write data fetch time */ +#define MR_RDH (1 << 10) /* Read data hold time */ +#define MR_FS (1 << 8) /* FIFO swap */ +#define MR_RST (1 << 7) /* S/W reset */ +#define MR_PB (1 << 4) /* Ping block */ +#define MR_DBS (1 << 2) /* Data bus swap */ +#define MR_IND (1 << 0) /* Indirect mode */ +#define W5300_IR 0x0002 /* Interrupt Register */ +#define W5300_IMR 0x0004 /* Interrupt Mask Register */ +#define IR_S0 0x0001 /* S0 interrupt */ +#define W5300_SHARL 0x0008 /* Source MAC address (0123) */ +#define W5300_SHARH 0x000c /* Source MAC address (45) */ +#define W5300_TMSRL 0x0020 /* Transmit Memory Size (0123) */ +#define W5300_TMSRH 0x0024 /* Transmit Memory Size (4567) */ +#define W5300_RMSRL 0x0028 /* Receive Memory Size (0123) */ +#define W5300_RMSRH 0x002c /* Receive Memory Size (4567) */ +#define W5300_MTYPE 0x0030 /* Memory Type */ +#define W5300_IDR 0x00fe /* Chip ID register */ +#define IDR_W5300 0x5300 /* =0x5300 for WIZnet W5300 */ +#define W5300_S0_MR 0x0200 /* S0 Mode Register */ +#define S0_MR_CLOSED 0x0000 /* Close mode */ +#define S0_MR_MACRAW 0x0004 /* MAC RAW mode (promiscous) */ +#define S0_MR_MACRAW_MF 0x0044 /* MAC RAW mode (filtered) */ +#define W5300_S0_CR 0x0202 /* S0 Command Register */ +#define S0_CR_OPEN 0x0001 /* OPEN command */ +#define S0_CR_CLOSE 0x0010 /* CLOSE command */ +#define S0_CR_SEND 0x0020 /* SEND command */ +#define S0_CR_RECV 0x0040 /* RECV command */ +#define W5300_S0_IMR 0x0204 /* S0 Interrupt Mask Register */ +#define W5300_S0_IR 0x0206 /* S0 Interrupt Register */ +#define S0_IR_RECV 0x0004 /* Receive interrupt */ +#define S0_IR_SENDOK 0x0010 /* Send OK interrupt */ +#define W5300_S0_SSR 0x0208 /* S0 Socket Status Register */ +#define W5300_S0_TX_WRSR 0x0220 /* S0 TX Write Size Register */ +#define W5300_S0_TX_FSR 0x0224 /* S0 TX Free Size Register */ +#define W5300_S0_RX_RSR 0x0228 /* S0 Received data Size */ +#define W5300_S0_TX_FIFO 0x022e /* S0 Transmit FIFO */ +#define W5300_S0_RX_FIFO 0x0230 /* S0 Receive FIFO */ +#define W5300_REGS_LEN 0x0400 + +/* + * Device driver private data structure + */ +struct w5300_priv { + void __iomem *base; + spinlock_t reg_lock; + bool indirect; + u16 (*read) (struct w5300_priv *priv, u16 addr); + void (*write)(struct w5300_priv *priv, u16 addr, u16 data); + int irq; + int link_irq; + int link_gpio; + + struct napi_struct napi; + struct net_device *ndev; + bool promisc; + u32 msg_enable; +}; + +/************************************************************************ + * + * Lowlevel I/O functions + * + ***********************************************************************/ + +/* + * In direct address mode host system can directly access W5300 registers + * after mapping to Memory-Mapped I/O space. + * + * 0x400 bytes are required for memory space. + */ +static inline u16 w5300_read_direct(struct w5300_priv *priv, u16 addr) +{ + return ioread16(priv->base + (addr << CONFIG_WIZNET_BUS_SHIFT)); +} + +static inline void w5300_write_direct(struct w5300_priv *priv, + u16 addr, u16 data) +{ + iowrite16(data, priv->base + (addr << CONFIG_WIZNET_BUS_SHIFT)); +} + +/* + * In indirect address mode host system indirectly accesses registers by + * using Indirect Mode Address Register (IDM_AR) and Indirect Mode Data + * Register (IDM_DR), which are directly mapped to Memory-Mapped I/O space. + * Mode Register (MR) is directly accessible. + * + * Only 0x06 bytes are required for memory space. + */ +#define W5300_IDM_AR 0x0002 /* Indirect Mode Address */ +#define W5300_IDM_DR 0x0004 /* Indirect Mode Data */ + +static u16 w5300_read_indirect(struct w5300_priv *priv, u16 addr) +{ + unsigned long flags; + u16 data; + + spin_lock_irqsave(&priv->reg_lock, flags); + w5300_write_direct(priv, W5300_IDM_AR, addr); + mmiowb(); + data = w5300_read_direct(priv, W5300_IDM_DR); + spin_unlock_irqrestore(&priv->reg_lock, flags); + + return data; +} + +static void w5300_write_indirect(struct w5300_priv *priv, u16 addr, u16 data) +{ + unsigned long flags; + + spin_lock_irqsave(&priv->reg_lock, flags); + w5300_write_direct(priv, W5300_IDM_AR, addr); + mmiowb(); + w5300_write_direct(priv, W5300_IDM_DR, data); + mmiowb(); + spin_unlock_irqrestore(&priv->reg_lock, flags); +} + +#if defined(CONFIG_WIZNET_BUS_DIRECT) +#define w5300_read w5300_read_direct +#define w5300_write w5300_write_direct + +#elif defined(CONFIG_WIZNET_BUS_INDIRECT) +#define w5300_read w5300_read_indirect +#define w5300_write w5300_write_indirect + +#else /* CONFIG_WIZNET_BUS_ANY */ +#define w5300_read priv->read +#define w5300_write priv->write +#endif + +static u32 w5300_read32(struct w5300_priv *priv, u16 addr) +{ + u32 data; + data = w5300_read(priv, addr) << 16; + data |= w5300_read(priv, addr + 2); + return data; +} + +static void w5300_write32(struct w5300_priv *priv, u16 addr, u32 data) +{ + w5300_write(priv, addr, data >> 16); + w5300_write(priv, addr + 2, data); +} + +static int w5300_command(struct w5300_priv *priv, u16 cmd) +{ + unsigned long timeout = jiffies + msecs_to_jiffies(100); + + w5300_write(priv, W5300_S0_CR, cmd); + mmiowb(); + + while (w5300_read(priv, W5300_S0_CR) != 0) { + if (time_after(jiffies, timeout)) + return -EIO; + cpu_relax(); + } + + return 0; +} + +static void w5300_read_frame(struct w5300_priv *priv, u8 *buf, int len) +{ + u16 fifo; + int i; + + for (i = 0; i < len; i += 2) { + fifo = w5300_read(priv, W5300_S0_RX_FIFO); + *buf++ = fifo >> 8; + *buf++ = fifo; + } + fifo = w5300_read(priv, W5300_S0_RX_FIFO); + fifo = w5300_read(priv, W5300_S0_RX_FIFO); +} + +static void w5300_write_frame(struct w5300_priv *priv, u8 *buf, int len) +{ + u16 fifo; + int i; + + for (i = 0; i < len; i += 2) { + fifo = *buf++ << 8; + fifo |= *buf++; + w5300_write(priv, W5300_S0_TX_FIFO, fifo); + } + w5300_write32(priv, W5300_S0_TX_WRSR, len); +} + +static void w5300_write_macaddr(struct w5300_priv *priv) +{ + struct net_device *ndev = priv->ndev; + w5300_write32(priv, W5300_SHARL, + ndev->dev_addr[0] << 24 | + ndev->dev_addr[1] << 16 | + ndev->dev_addr[2] << 8 | + ndev->dev_addr[3]); + w5300_write(priv, W5300_SHARH, + ndev->dev_addr[4] << 8 | + ndev->dev_addr[5]); + mmiowb(); +} + +static void w5300_hw_reset(struct w5300_priv *priv) +{ + w5300_write_direct(priv, W5300_MR, MR_RST); + mmiowb(); + mdelay(5); + w5300_write_direct(priv, W5300_MR, priv->indirect ? + MR_WDF(7) | MR_PB | MR_IND : + MR_WDF(7) | MR_PB); + mmiowb(); + w5300_write(priv, W5300_IMR, 0); + w5300_write_macaddr(priv); + + /* Configure 128K of internal memory + * as 64K RX fifo and 64K TX fifo + */ + w5300_write32(priv, W5300_RMSRL, 64 << 24); + w5300_write32(priv, W5300_RMSRH, 0); + w5300_write32(priv, W5300_TMSRL, 64 << 24); + w5300_write32(priv, W5300_TMSRH, 0); + w5300_write(priv, W5300_MTYPE, 0x00ff); + mmiowb(); +} + +static void w5300_hw_start(struct w5300_priv *priv) +{ + w5300_write(priv, W5300_S0_MR, priv->promisc ? + S0_MR_MACRAW : S0_MR_MACRAW_MF); + mmiowb(); + w5300_command(priv, S0_CR_OPEN); + w5300_write(priv, W5300_S0_IMR, IS_ENABLED(CONFIG_WIZNET_TX_FLOW) ? + S0_IR_RECV | S0_IR_SENDOK : + S0_IR_RECV); + w5300_write(priv, W5300_IMR, IR_S0); + mmiowb(); +} + +static void w5300_hw_close(struct w5300_priv *priv) +{ + w5300_write(priv, W5300_IMR, 0); + mmiowb(); + w5300_command(priv, S0_CR_CLOSE); +} + +/*********************************************************************** + * + * Device driver functions / callbacks + * + ***********************************************************************/ + +static void w5300_get_drvinfo(struct net_device *ndev, + struct ethtool_drvinfo *info) +{ + strlcpy(info->driver, DRV_NAME, sizeof(info->driver)); + strlcpy(info->version, DRV_VERSION, sizeof(info->version)); + strlcpy(info->bus_info, dev_name(ndev->dev.parent), + sizeof(info->bus_info)); +} + +static u32 w5300_get_link(struct net_device *ndev) +{ + struct w5300_priv *priv = netdev_priv(ndev); + + if (gpio_is_valid(priv->link_gpio)) + return !!gpio_get_value(priv->link_gpio); + + return 1; +} + +static u32 w5300_get_msglevel(struct net_device *ndev) +{ + struct w5300_priv *priv = netdev_priv(ndev); + + return priv->msg_enable; +} + +static void w5300_set_msglevel(struct net_device *ndev, u32 value) +{ + struct w5300_priv *priv = netdev_priv(ndev); + + priv->msg_enable = value; +} + +static int w5300_get_regs_len(struct net_device *ndev) +{ + return W5300_REGS_LEN; +} + +static void w5300_get_regs(struct net_device *ndev, + struct ethtool_regs *regs, void *_buf) +{ + struct w5300_priv *priv = netdev_priv(ndev); + u8 *buf = _buf; + u16 addr; + u16 data; + + regs->version = 1; + for (addr = 0; addr < W5300_REGS_LEN; addr += 2) { + switch (addr & 0x23f) { + case W5300_S0_TX_FIFO: /* cannot read TX_FIFO */ + case W5300_S0_RX_FIFO: /* cannot read RX_FIFO */ + data = 0xffff; + break; + default: + data = w5300_read(priv, addr); + break; + } + *buf++ = data >> 8; + *buf++ = data; + } +} + +static void w5300_tx_timeout(struct net_device *ndev) +{ + struct w5300_priv *priv = netdev_priv(ndev); + + netif_stop_queue(ndev); + w5300_hw_reset(priv); + w5300_hw_start(priv); + ndev->stats.tx_errors++; + ndev->trans_start = jiffies; + netif_wake_queue(ndev); +} + +static int w5300_start_tx(struct sk_buff *skb, struct net_device *ndev) +{ + struct w5300_priv *priv = netdev_priv(ndev); + + if (IS_ENABLED(CONFIG_WIZNET_TX_FLOW)) + netif_stop_queue(ndev); + + w5300_write_frame(priv, skb->data, skb->len); + mmiowb(); + ndev->stats.tx_packets++; + ndev->stats.tx_bytes += skb->len; + dev_kfree_skb(skb); + netif_dbg(priv, tx_queued, ndev, "tx queued\n"); + + w5300_command(priv, S0_CR_SEND); + + return NETDEV_TX_OK; +} + +static int w5300_napi_poll(struct napi_struct *napi, int budget) +{ + struct w5300_priv *priv = container_of(napi, struct w5300_priv, napi); + struct net_device *ndev = priv->ndev; + struct sk_buff *skb; + int rx_count; + u16 rx_len; + + for (rx_count = 0; rx_count < budget; rx_count++) { + u32 rx_fifo_len = w5300_read32(priv, W5300_S0_RX_RSR); + if (rx_fifo_len == 0) + break; + + rx_len = w5300_read(priv, W5300_S0_RX_FIFO); + + skb = netdev_alloc_skb_ip_align(ndev, roundup(rx_len, 2)); + if (unlikely(!skb)) { + u32 i; + for (i = 0; i < rx_fifo_len; i += 2) + w5300_read(priv, W5300_S0_RX_FIFO); + ndev->stats.rx_dropped++; + return -ENOMEM; + } + + skb_put(skb, rx_len); + w5300_read_frame(priv, skb->data, rx_len); + skb->protocol = eth_type_trans(skb, ndev); + + netif_receive_skb(skb); + ndev->stats.rx_packets++; + ndev->stats.rx_bytes += rx_len; + } + + if (rx_count < budget) { + w5300_write(priv, W5300_IMR, IR_S0); + mmiowb(); + napi_complete(napi); + } + + return rx_count; +} + +static irqreturn_t w5300_interrupt(int irq, void *ndev_instance) +{ + struct net_device *ndev = ndev_instance; + struct w5300_priv *priv = netdev_priv(ndev); + + int ir = w5300_read(priv, W5300_S0_IR); + if (!ir) + return IRQ_NONE; + w5300_write(priv, W5300_S0_IR, ir); + mmiowb(); + + if (IS_ENABLED(CONFIG_WIZNET_TX_FLOW) && (ir & S0_IR_SENDOK)) { + netif_dbg(priv, tx_done, ndev, "tx done\n"); + netif_wake_queue(ndev); + } + + if (ir & S0_IR_RECV) { + if (napi_schedule_prep(&priv->napi)) { + w5300_write(priv, W5300_IMR, 0); + mmiowb(); + __napi_schedule(&priv->napi); + } + } + + return IRQ_HANDLED; +} + +static irqreturn_t w5300_detect_link(int irq, void *ndev_instance) +{ + struct net_device *ndev = ndev_instance; + struct w5300_priv *priv = netdev_priv(ndev); + + if (netif_running(ndev)) { + if (gpio_get_value(priv->link_gpio) != 0) { + netif_info(priv, link, ndev, "link is up\n"); + netif_carrier_on(ndev); + } else { + netif_info(priv, link, ndev, "link is down\n"); + netif_carrier_off(ndev); + } + } + + return IRQ_HANDLED; +} + +static void w5300_set_rx_mode(struct net_device *ndev) +{ + struct w5300_priv *priv = netdev_priv(ndev); + bool set_promisc = (ndev->flags & IFF_PROMISC) != 0; + + if (priv->promisc != set_promisc) { + priv->promisc = set_promisc; + w5300_hw_start(priv); + } +} + +static int w5300_set_macaddr(struct net_device *ndev, void *addr) +{ + struct w5300_priv *priv = netdev_priv(ndev); + struct sockaddr *sock_addr = addr; + + if (!is_valid_ether_addr(sock_addr->sa_data)) + return -EADDRNOTAVAIL; + memcpy(ndev->dev_addr, sock_addr->sa_data, ETH_ALEN); + ndev->addr_assign_type &= ~NET_ADDR_RANDOM; + w5300_write_macaddr(priv); + return 0; +} + +static int w5300_open(struct net_device *ndev) +{ + struct w5300_priv *priv = netdev_priv(ndev); + + netif_info(priv, ifup, ndev, "enabling\n"); + if (!is_valid_ether_addr(ndev->dev_addr)) + return -EINVAL; + w5300_hw_start(priv); + napi_enable(&priv->napi); + netif_start_queue(ndev); + if (!gpio_is_valid(priv->link_gpio) || + gpio_get_value(priv->link_gpio) != 0) + netif_carrier_on(ndev); + return 0; +} + +static int w5300_stop(struct net_device *ndev) +{ + struct w5300_priv *priv = netdev_priv(ndev); + + netif_info(priv, ifdown, ndev, "shutting down\n"); + w5300_hw_close(priv); + netif_carrier_off(ndev); + netif_stop_queue(ndev); + napi_disable(&priv->napi); + return 0; +} + +static const struct ethtool_ops w5300_ethtool_ops = { + .get_drvinfo = w5300_get_drvinfo, + .get_msglevel = w5300_get_msglevel, + .set_msglevel = w5300_set_msglevel, + .get_link = w5300_get_link, + .get_regs_len = w5300_get_regs_len, + .get_regs = w5300_get_regs, +}; + +static const struct net_device_ops w5300_netdev_ops = { + .ndo_open = w5300_open, + .ndo_stop = w5300_stop, + .ndo_start_xmit = w5300_start_tx, + .ndo_tx_timeout = w5300_tx_timeout, + .ndo_set_rx_mode = w5300_set_rx_mode, + .ndo_set_mac_address = w5300_set_macaddr, + .ndo_validate_addr = eth_validate_addr, + .ndo_change_mtu = eth_change_mtu, +}; + +static int __devinit w5300_hw_probe(struct platform_device *pdev) +{ + struct wiznet_platform_data *data = pdev->dev.platform_data; + struct net_device *ndev = platform_get_drvdata(pdev); + struct w5300_priv *priv = netdev_priv(ndev); + const char *name = netdev_name(ndev); + struct resource *mem; + int mem_size; + int irq; + int ret; + + if (data && is_valid_ether_addr(data->mac_addr)) { + memcpy(ndev->dev_addr, data->mac_addr, ETH_ALEN); + } else { + random_ether_addr(ndev->dev_addr); + ndev->addr_assign_type |= NET_ADDR_RANDOM; + } + + mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!mem) + return -ENXIO; + mem_size = resource_size(mem); + if (!devm_request_mem_region(&pdev->dev, mem->start, mem_size, name)) + return -EBUSY; + priv->base = devm_ioremap(&pdev->dev, mem->start, mem_size); + if (!priv->base) + return -EBUSY; + + spin_lock_init(&priv->reg_lock); + priv->indirect = mem_size < W5300_BUS_DIRECT_SIZE; + if (priv->indirect) { + priv->read = w5300_read_indirect; + priv->write = w5300_write_indirect; + } else { + priv->read = w5300_read_direct; + priv->write = w5300_write_direct; + } + + w5300_hw_reset(priv); + if (w5300_read(priv, W5300_IDR) != IDR_W5300) + return -ENODEV; + + irq = platform_get_irq(pdev, 0); + if (irq < 0) + return irq; + ret = request_irq(irq, w5300_interrupt, + IRQ_TYPE_LEVEL_LOW, name, ndev); + if (ret < 0) + return ret; + priv->irq = irq; + + priv->link_gpio = data->link_gpio; + if (gpio_is_valid(priv->link_gpio)) { + char *link_name = devm_kzalloc(&pdev->dev, 16, GFP_KERNEL); + if (!link_name) + return -ENOMEM; + snprintf(link_name, 16, "%s-link", name); + priv->link_irq = gpio_to_irq(priv->link_gpio); + if (request_any_context_irq(priv->link_irq, w5300_detect_link, + IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, + link_name, priv->ndev) < 0) + priv->link_gpio = -EINVAL; + } + + netdev_info(ndev, "at 0x%llx irq %d\n", (u64)mem->start, irq); + return 0; +} + +static int __devinit w5300_probe(struct platform_device *pdev) +{ + struct w5300_priv *priv; + struct net_device *ndev; + int err; + + ndev = alloc_etherdev(sizeof(*priv)); + if (!ndev) + return -ENOMEM; + SET_NETDEV_DEV(ndev, &pdev->dev); + platform_set_drvdata(pdev, ndev); + priv = netdev_priv(ndev); + priv->ndev = ndev; + + ether_setup(ndev); + ndev->netdev_ops = &w5300_netdev_ops; + ndev->ethtool_ops = &w5300_ethtool_ops; + ndev->watchdog_timeo = HZ; + netif_napi_add(ndev, &priv->napi, w5300_napi_poll, 16); + + /* This chip doesn't support VLAN packets with normal MTU, + * so disable VLAN for this device. + */ + ndev->features |= NETIF_F_VLAN_CHALLENGED; + + err = register_netdev(ndev); + if (err < 0) + goto err_register; + + err = w5300_hw_probe(pdev); + if (err < 0) + goto err_hw_probe; + + return 0; + +err_hw_probe: + unregister_netdev(ndev); +err_register: + free_netdev(ndev); + platform_set_drvdata(pdev, NULL); + return err; +} + +static int __devexit w5300_remove(struct platform_device *pdev) +{ + struct net_device *ndev = platform_get_drvdata(pdev); + struct w5300_priv *priv = netdev_priv(ndev); + + w5300_hw_reset(priv); + free_irq(priv->irq, ndev); + if (gpio_is_valid(priv->link_gpio)) + free_irq(priv->link_irq, ndev); + + unregister_netdev(ndev); + free_netdev(ndev); + platform_set_drvdata(pdev, NULL); + return 0; +} + +#ifdef CONFIG_PM +static int w5300_suspend(struct device *dev) +{ + struct platform_device *pdev = to_platform_device(dev); + struct net_device *ndev = platform_get_drvdata(pdev); + struct w5300_priv *priv = netdev_priv(ndev); + + if (netif_running(ndev)) { + netif_carrier_off(ndev); + netif_device_detach(ndev); + + w5300_hw_close(priv); + } + return 0; +} + +static int w5300_resume(struct device *dev) +{ + struct platform_device *pdev = to_platform_device(dev); + struct net_device *ndev = platform_get_drvdata(pdev); + struct w5300_priv *priv = netdev_priv(ndev); + + if (!netif_running(ndev)) { + w5300_hw_reset(priv); + w5300_hw_start(priv); + + netif_device_attach(ndev); + if (!gpio_is_valid(priv->link_gpio) || + gpio_get_value(priv->link_gpio) != 0) + netif_carrier_on(ndev); + } + return 0; +} +#endif /* CONFIG_PM */ + +static SIMPLE_DEV_PM_OPS(w5300_pm_ops, w5300_suspend, w5300_resume); + +static struct platform_driver w5300_driver = { + .driver = { + .name = DRV_NAME, + .owner = THIS_MODULE, + .pm = &w5300_pm_ops, + }, + .probe = w5300_probe, + .remove = __devexit_p(w5300_remove), +}; + +module_platform_driver(w5300_driver); diff --git a/include/linux/platform_data/wiznet.h b/include/linux/platform_data/wiznet.h new file mode 100644 index 000000000000..b5d8c192d84d --- /dev/null +++ b/include/linux/platform_data/wiznet.h @@ -0,0 +1,24 @@ +/* + * Ethernet driver for the WIZnet W5x00 chip. + * + * Licensed under the GPL-2 or later. + */ + +#ifndef PLATFORM_DATA_WIZNET_H +#define PLATFORM_DATA_WIZNET_H + +#include + +struct wiznet_platform_data { + int link_gpio; + u8 mac_addr[ETH_ALEN]; +}; + +#ifndef CONFIG_WIZNET_BUS_SHIFT +#define CONFIG_WIZNET_BUS_SHIFT 0 +#endif + +#define W5100_BUS_DIRECT_SIZE (0x8000 << CONFIG_WIZNET_BUS_SHIFT) +#define W5300_BUS_DIRECT_SIZE (0x0400 << CONFIG_WIZNET_BUS_SHIFT) + +#endif /* PLATFORM_DATA_WIZNET_H */