From: Jes Sorensen Date: Thu, 14 Apr 2016 18:58:42 +0000 (-0400) Subject: rtl8xxxu: Reorder parts of init code to match the 8192eu vendor code flow X-Git-Url: https://git.karo-electronics.de/?a=commitdiff_plain;h=c157863d99797f6fed60e6e56d53afeb0bc3b436;p=linux-beck.git rtl8xxxu: Reorder parts of init code to match the 8192eu vendor code flow In order to debug 8192eu support, reorder some init code to match the flow of the vendor driver. Signed-off-by: Jes Sorensen Signed-off-by: Kalle Valo --- diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c index e36fda8c1ad3..d67b88665194 100644 --- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c +++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c @@ -7592,6 +7592,26 @@ static int rtl8xxxu_init_device(struct ieee80211_hw *hw) if (ret) goto exit; + /* RFSW Control - clear bit 14 ?? */ + if (priv->rtl_chip != RTL8723B) + rtl8xxxu_write32(priv, REG_FPGA0_TX_INFO, 0x00000003); + /* 0x07000760 */ + if (priv->rtl_chip == RTL8192E) { + val32 = 0; + } else { + val32 = FPGA0_RF_TRSW | FPGA0_RF_TRSWB | FPGA0_RF_ANTSW | + FPGA0_RF_ANTSWB | FPGA0_RF_PAPE | + ((FPGA0_RF_ANTSW | FPGA0_RF_ANTSWB | FPGA0_RF_PAPE) << + FPGA0_RF_BD_CTRL_SHIFT); + } + rtl8xxxu_write32(priv, REG_FPGA0_XAB_RF_SW_CTRL, val32); + /* 0x860[6:5]= 00 - why? - this sets antenna B */ + if (priv->rtl_chip != RTL8192E) + rtl8xxxu_write32(priv, REG_FPGA0_XA_RF_INT_OE, 0x66f60210); + + priv->rf_mode_ag[0] = rtl8xxxu_read_rfreg(priv, RF_A, + RF6052_REG_MODE_AG); + /* * Chip specific quirks */ @@ -7653,21 +7673,6 @@ static int rtl8xxxu_init_device(struct ieee80211_hw *hw) if (ret) goto exit; - /* RFSW Control - clear bit 14 ?? */ - if (priv->rtl_chip != RTL8723B) - rtl8xxxu_write32(priv, REG_FPGA0_TX_INFO, 0x00000003); - /* 0x07000760 */ - val32 = FPGA0_RF_TRSW | FPGA0_RF_TRSWB | FPGA0_RF_ANTSW | - FPGA0_RF_ANTSWB | FPGA0_RF_PAPE | - ((FPGA0_RF_ANTSW | FPGA0_RF_ANTSWB | FPGA0_RF_PAPE) << - FPGA0_RF_BD_CTRL_SHIFT); - rtl8xxxu_write32(priv, REG_FPGA0_XAB_RF_SW_CTRL, val32); - /* 0x860[6:5]= 00 - why? - this sets antenna B */ - rtl8xxxu_write32(priv, REG_FPGA0_XA_RF_INT_OE, 0x66F60210); - - priv->rf_mode_ag[0] = rtl8xxxu_read_rfreg(priv, RF_A, - RF6052_REG_MODE_AG); - /* * Set RX page boundary */