From: Markus Pargmann Date: Wed, 12 Aug 2015 14:50:04 +0000 (+0200) Subject: iio: bmg160: Use i2c regmap instead of direct i2c access X-Git-Url: https://git.karo-electronics.de/?a=commitdiff_plain;h=c6c9e995bcd8349f271b39e6abd9bd2f090ec5bd;p=linux-beck.git iio: bmg160: Use i2c regmap instead of direct i2c access This patch introduces regmap usage into the driver. This is done to later easily support the SPI interface of this chip. Signed-off-by: Markus Pargmann Reviewed-by: Srinivas Pandruvada Signed-off-by: Jonathan Cameron --- diff --git a/drivers/iio/gyro/Kconfig b/drivers/iio/gyro/Kconfig index 8d2439345673..cf82d74139a2 100644 --- a/drivers/iio/gyro/Kconfig +++ b/drivers/iio/gyro/Kconfig @@ -55,6 +55,7 @@ config BMG160 depends on I2C select IIO_BUFFER select IIO_TRIGGERED_BUFFER + select REGMAP_I2C help Say yes here to build support for Bosch BMG160 Tri-axis Gyro Sensor driver. This driver also supports BMI055 gyroscope. diff --git a/drivers/iio/gyro/bmg160.c b/drivers/iio/gyro/bmg160.c index 460bf715d541..d3c5300a3862 100644 --- a/drivers/iio/gyro/bmg160.c +++ b/drivers/iio/gyro/bmg160.c @@ -28,6 +28,7 @@ #include #include #include +#include #define BMG160_DRV_NAME "bmg160" #define BMG160_IRQ_NAME "bmg160_event" @@ -98,6 +99,7 @@ struct bmg160_data { struct i2c_client *client; + struct regmap *regmap; struct iio_trigger *dready_trig; struct iio_trigger *motion_trig; struct mutex mutex; @@ -134,12 +136,17 @@ static const struct { { 133, BMG160_RANGE_250DPS}, { 66, BMG160_RANGE_125DPS} }; +static struct regmap_config bmg160_regmap_i2c_conf = { + .reg_bits = 8, + .val_bits = 8, + .max_register = 0x3f +}; + static int bmg160_set_mode(struct bmg160_data *data, u8 mode) { int ret; - ret = i2c_smbus_write_byte_data(data->client, - BMG160_REG_PMU_LPW, mode); + ret = regmap_write(data->regmap, BMG160_REG_PMU_LPW, mode); if (ret < 0) { dev_err(&data->client->dev, "Error writing reg_pmu_lpw\n"); return ret; @@ -169,8 +176,7 @@ static int bmg160_set_bw(struct bmg160_data *data, int val) if (bw_bits < 0) return bw_bits; - ret = i2c_smbus_write_byte_data(data->client, BMG160_REG_PMU_BW, - bw_bits); + ret = regmap_write(data->regmap, BMG160_REG_PMU_BW, bw_bits); if (ret < 0) { dev_err(&data->client->dev, "Error writing reg_pmu_bw\n"); return ret; @@ -184,16 +190,17 @@ static int bmg160_set_bw(struct bmg160_data *data, int val) static int bmg160_chip_init(struct bmg160_data *data) { int ret; + unsigned int val; - ret = i2c_smbus_read_byte_data(data->client, BMG160_REG_CHIP_ID); + ret = regmap_read(data->regmap, BMG160_REG_CHIP_ID, &val); if (ret < 0) { dev_err(&data->client->dev, "Error reading reg_chip_id\n"); return ret; } - dev_dbg(&data->client->dev, "Chip Id %x\n", ret); - if (ret != BMG160_CHIP_ID_VAL) { - dev_err(&data->client->dev, "invalid chip %x\n", ret); + dev_dbg(&data->client->dev, "Chip Id %x\n", val); + if (val != BMG160_CHIP_ID_VAL) { + dev_err(&data->client->dev, "invalid chip %x\n", val); return -ENODEV; } @@ -210,40 +217,31 @@ static int bmg160_chip_init(struct bmg160_data *data) return ret; /* Set Default Range */ - ret = i2c_smbus_write_byte_data(data->client, - BMG160_REG_RANGE, - BMG160_RANGE_500DPS); + ret = regmap_write(data->regmap, BMG160_REG_RANGE, BMG160_RANGE_500DPS); if (ret < 0) { dev_err(&data->client->dev, "Error writing reg_range\n"); return ret; } data->dps_range = BMG160_RANGE_500DPS; - ret = i2c_smbus_read_byte_data(data->client, BMG160_REG_SLOPE_THRES); + ret = regmap_read(data->regmap, BMG160_REG_SLOPE_THRES, &val); if (ret < 0) { dev_err(&data->client->dev, "Error reading reg_slope_thres\n"); return ret; } - data->slope_thres = ret; + data->slope_thres = val; /* Set default interrupt mode */ - ret = i2c_smbus_read_byte_data(data->client, BMG160_REG_INT_EN_1); - if (ret < 0) { - dev_err(&data->client->dev, "Error reading reg_int_en_1\n"); - return ret; - } - ret &= ~BMG160_INT1_BIT_OD; - ret = i2c_smbus_write_byte_data(data->client, - BMG160_REG_INT_EN_1, ret); + ret = regmap_update_bits(data->regmap, BMG160_REG_INT_EN_1, + BMG160_INT1_BIT_OD, 0); if (ret < 0) { - dev_err(&data->client->dev, "Error writing reg_int_en_1\n"); + dev_err(&data->client->dev, "Error updating bits in reg_int_en_1\n"); return ret; } - ret = i2c_smbus_write_byte_data(data->client, - BMG160_REG_INT_RST_LATCH, - BMG160_INT_MODE_LATCH_INT | - BMG160_INT_MODE_LATCH_RESET); + ret = regmap_write(data->regmap, BMG160_REG_INT_RST_LATCH, + BMG160_INT_MODE_LATCH_INT | + BMG160_INT_MODE_LATCH_RESET); if (ret < 0) { dev_err(&data->client->dev, "Error writing reg_motion_intr\n"); @@ -284,41 +282,28 @@ static int bmg160_setup_any_motion_interrupt(struct bmg160_data *data, int ret; /* Enable/Disable INT_MAP0 mapping */ - ret = i2c_smbus_read_byte_data(data->client, BMG160_REG_INT_MAP_0); - if (ret < 0) { - dev_err(&data->client->dev, "Error reading reg_int_map0\n"); - return ret; - } - if (status) - ret |= BMG160_INT_MAP_0_BIT_ANY; - else - ret &= ~BMG160_INT_MAP_0_BIT_ANY; - - ret = i2c_smbus_write_byte_data(data->client, - BMG160_REG_INT_MAP_0, - ret); + ret = regmap_update_bits(data->regmap, BMG160_REG_INT_MAP_0, + BMG160_INT_MAP_0_BIT_ANY, + (status ? BMG160_INT_MAP_0_BIT_ANY : 0)); if (ret < 0) { - dev_err(&data->client->dev, "Error writing reg_int_map0\n"); + dev_err(&data->client->dev, "Error updating bits reg_int_map0\n"); return ret; } /* Enable/Disable slope interrupts */ if (status) { /* Update slope thres */ - ret = i2c_smbus_write_byte_data(data->client, - BMG160_REG_SLOPE_THRES, - data->slope_thres); + ret = regmap_write(data->regmap, BMG160_REG_SLOPE_THRES, + data->slope_thres); if (ret < 0) { dev_err(&data->client->dev, "Error writing reg_slope_thres\n"); return ret; } - ret = i2c_smbus_write_byte_data(data->client, - BMG160_REG_MOTION_INTR, - BMG160_INT_MOTION_X | - BMG160_INT_MOTION_Y | - BMG160_INT_MOTION_Z); + ret = regmap_write(data->regmap, BMG160_REG_MOTION_INTR, + BMG160_INT_MOTION_X | BMG160_INT_MOTION_Y | + BMG160_INT_MOTION_Z); if (ret < 0) { dev_err(&data->client->dev, "Error writing reg_motion_intr\n"); @@ -331,10 +316,10 @@ static int bmg160_setup_any_motion_interrupt(struct bmg160_data *data, * to set latched mode, we will be flooded anyway with INTR */ if (!data->dready_trigger_on) { - ret = i2c_smbus_write_byte_data(data->client, - BMG160_REG_INT_RST_LATCH, - BMG160_INT_MODE_LATCH_INT | - BMG160_INT_MODE_LATCH_RESET); + ret = regmap_write(data->regmap, + BMG160_REG_INT_RST_LATCH, + BMG160_INT_MODE_LATCH_INT | + BMG160_INT_MODE_LATCH_RESET); if (ret < 0) { dev_err(&data->client->dev, "Error writing reg_rst_latch\n"); @@ -342,14 +327,12 @@ static int bmg160_setup_any_motion_interrupt(struct bmg160_data *data, } } - ret = i2c_smbus_write_byte_data(data->client, - BMG160_REG_INT_EN_0, - BMG160_DATA_ENABLE_INT); + ret = regmap_write(data->regmap, BMG160_REG_INT_EN_0, + BMG160_DATA_ENABLE_INT); - } else - ret = i2c_smbus_write_byte_data(data->client, - BMG160_REG_INT_EN_0, - 0); + } else { + ret = regmap_write(data->regmap, BMG160_REG_INT_EN_0, 0); + } if (ret < 0) { dev_err(&data->client->dev, "Error writing reg_int_en0\n"); @@ -365,55 +348,39 @@ static int bmg160_setup_new_data_interrupt(struct bmg160_data *data, int ret; /* Enable/Disable INT_MAP1 mapping */ - ret = i2c_smbus_read_byte_data(data->client, BMG160_REG_INT_MAP_1); - if (ret < 0) { - dev_err(&data->client->dev, "Error reading reg_int_map1\n"); - return ret; - } - - if (status) - ret |= BMG160_INT_MAP_1_BIT_NEW_DATA; - else - ret &= ~BMG160_INT_MAP_1_BIT_NEW_DATA; - - ret = i2c_smbus_write_byte_data(data->client, - BMG160_REG_INT_MAP_1, - ret); + ret = regmap_update_bits(data->regmap, BMG160_REG_INT_MAP_1, + BMG160_INT_MAP_1_BIT_NEW_DATA, + (status ? BMG160_INT_MAP_1_BIT_NEW_DATA : 0)); if (ret < 0) { - dev_err(&data->client->dev, "Error writing reg_int_map1\n"); + dev_err(&data->client->dev, "Error updating bits in reg_int_map1\n"); return ret; } if (status) { - ret = i2c_smbus_write_byte_data(data->client, - BMG160_REG_INT_RST_LATCH, - BMG160_INT_MODE_NON_LATCH_INT | - BMG160_INT_MODE_LATCH_RESET); + ret = regmap_write(data->regmap, BMG160_REG_INT_RST_LATCH, + BMG160_INT_MODE_NON_LATCH_INT | + BMG160_INT_MODE_LATCH_RESET); if (ret < 0) { dev_err(&data->client->dev, "Error writing reg_rst_latch\n"); return ret; } - ret = i2c_smbus_write_byte_data(data->client, - BMG160_REG_INT_EN_0, - BMG160_DATA_ENABLE_INT); + ret = regmap_write(data->regmap, BMG160_REG_INT_EN_0, + BMG160_DATA_ENABLE_INT); } else { /* Restore interrupt mode */ - ret = i2c_smbus_write_byte_data(data->client, - BMG160_REG_INT_RST_LATCH, - BMG160_INT_MODE_LATCH_INT | - BMG160_INT_MODE_LATCH_RESET); + ret = regmap_write(data->regmap, BMG160_REG_INT_RST_LATCH, + BMG160_INT_MODE_LATCH_INT | + BMG160_INT_MODE_LATCH_RESET); if (ret < 0) { dev_err(&data->client->dev, "Error writing reg_rst_latch\n"); return ret; } - ret = i2c_smbus_write_byte_data(data->client, - BMG160_REG_INT_EN_0, - 0); + ret = regmap_write(data->regmap, BMG160_REG_INT_EN_0, 0); } if (ret < 0) { @@ -444,10 +411,8 @@ static int bmg160_set_scale(struct bmg160_data *data, int val) for (i = 0; i < ARRAY_SIZE(bmg160_scale_table); ++i) { if (bmg160_scale_table[i].scale == val) { - ret = i2c_smbus_write_byte_data( - data->client, - BMG160_REG_RANGE, - bmg160_scale_table[i].dps_range); + ret = regmap_write(data->regmap, BMG160_REG_RANGE, + bmg160_scale_table[i].dps_range); if (ret < 0) { dev_err(&data->client->dev, "Error writing reg_range\n"); @@ -464,6 +429,7 @@ static int bmg160_set_scale(struct bmg160_data *data, int val) static int bmg160_get_temp(struct bmg160_data *data, int *val) { int ret; + unsigned int raw_val; mutex_lock(&data->mutex); ret = bmg160_set_power_state(data, true); @@ -472,7 +438,7 @@ static int bmg160_get_temp(struct bmg160_data *data, int *val) return ret; } - ret = i2c_smbus_read_byte_data(data->client, BMG160_REG_TEMP); + ret = regmap_read(data->regmap, BMG160_REG_TEMP, &raw_val); if (ret < 0) { dev_err(&data->client->dev, "Error reading reg_temp\n"); bmg160_set_power_state(data, false); @@ -480,7 +446,7 @@ static int bmg160_get_temp(struct bmg160_data *data, int *val) return ret; } - *val = sign_extend32(ret, 7); + *val = sign_extend32(raw_val, 7); ret = bmg160_set_power_state(data, false); mutex_unlock(&data->mutex); if (ret < 0) @@ -492,6 +458,7 @@ static int bmg160_get_temp(struct bmg160_data *data, int *val) static int bmg160_get_axis(struct bmg160_data *data, int axis, int *val) { int ret; + unsigned int raw_val; mutex_lock(&data->mutex); ret = bmg160_set_power_state(data, true); @@ -500,7 +467,8 @@ static int bmg160_get_axis(struct bmg160_data *data, int axis, int *val) return ret; } - ret = i2c_smbus_read_word_data(data->client, BMG160_AXIS_TO_REG(axis)); + ret = regmap_bulk_read(data->regmap, BMG160_AXIS_TO_REG(axis), &raw_val, + 2); if (ret < 0) { dev_err(&data->client->dev, "Error reading axis %d\n", axis); bmg160_set_power_state(data, false); @@ -508,7 +476,7 @@ static int bmg160_get_axis(struct bmg160_data *data, int axis, int *val) return ret; } - *val = sign_extend32(ret, 15); + *val = sign_extend32(raw_val, 15); ret = bmg160_set_power_state(data, false); mutex_unlock(&data->mutex); if (ret < 0) @@ -807,12 +775,13 @@ static irqreturn_t bmg160_trigger_handler(int irq, void *p) struct iio_dev *indio_dev = pf->indio_dev; struct bmg160_data *data = iio_priv(indio_dev); int bit, ret, i = 0; + unsigned int val; mutex_lock(&data->mutex); for_each_set_bit(bit, indio_dev->active_scan_mask, indio_dev->masklength) { - ret = i2c_smbus_read_word_data(data->client, - BMG160_AXIS_TO_REG(bit)); + ret = regmap_bulk_read(data->regmap, BMG160_AXIS_TO_REG(bit), + &val, 2); if (ret < 0) { mutex_unlock(&data->mutex); goto err; @@ -840,10 +809,9 @@ static int bmg160_trig_try_reen(struct iio_trigger *trig) return 0; /* Set latched mode interrupt and clear any latched interrupt */ - ret = i2c_smbus_write_byte_data(data->client, - BMG160_REG_INT_RST_LATCH, - BMG160_INT_MODE_LATCH_INT | - BMG160_INT_MODE_LATCH_RESET); + ret = regmap_write(data->regmap, BMG160_REG_INT_RST_LATCH, + BMG160_INT_MODE_LATCH_INT | + BMG160_INT_MODE_LATCH_RESET); if (ret < 0) { dev_err(&data->client->dev, "Error writing reg_rst_latch\n"); return ret; @@ -907,33 +875,34 @@ static irqreturn_t bmg160_event_handler(int irq, void *private) struct bmg160_data *data = iio_priv(indio_dev); int ret; int dir; + unsigned int val; - ret = i2c_smbus_read_byte_data(data->client, BMG160_REG_INT_STATUS_2); + ret = regmap_read(data->regmap, BMG160_REG_INT_STATUS_2, &val); if (ret < 0) { dev_err(&data->client->dev, "Error reading reg_int_status2\n"); goto ack_intr_status; } - if (ret & 0x08) + if (val & 0x08) dir = IIO_EV_DIR_RISING; else dir = IIO_EV_DIR_FALLING; - if (ret & BMG160_ANY_MOTION_BIT_X) + if (val & BMG160_ANY_MOTION_BIT_X) iio_push_event(indio_dev, IIO_MOD_EVENT_CODE(IIO_ANGL_VEL, 0, IIO_MOD_X, IIO_EV_TYPE_ROC, dir), iio_get_time_ns()); - if (ret & BMG160_ANY_MOTION_BIT_Y) + if (val & BMG160_ANY_MOTION_BIT_Y) iio_push_event(indio_dev, IIO_MOD_EVENT_CODE(IIO_ANGL_VEL, 0, IIO_MOD_Y, IIO_EV_TYPE_ROC, dir), iio_get_time_ns()); - if (ret & BMG160_ANY_MOTION_BIT_Z) + if (val & BMG160_ANY_MOTION_BIT_Z) iio_push_event(indio_dev, IIO_MOD_EVENT_CODE(IIO_ANGL_VEL, 0, IIO_MOD_Z, @@ -943,10 +912,9 @@ static irqreturn_t bmg160_event_handler(int irq, void *private) ack_intr_status: if (!data->dready_trigger_on) { - ret = i2c_smbus_write_byte_data(data->client, - BMG160_REG_INT_RST_LATCH, - BMG160_INT_MODE_LATCH_INT | - BMG160_INT_MODE_LATCH_RESET); + ret = regmap_write(data->regmap, BMG160_REG_INT_RST_LATCH, + BMG160_INT_MODE_LATCH_INT | + BMG160_INT_MODE_LATCH_RESET); if (ret < 0) dev_err(&data->client->dev, "Error writing reg_rst_latch\n"); @@ -1038,6 +1006,14 @@ static int bmg160_probe(struct i2c_client *client, struct iio_dev *indio_dev; int ret; const char *name = NULL; + struct regmap *regmap; + + regmap = devm_regmap_init_i2c(client, &bmg160_regmap_i2c_conf); + if (IS_ERR(regmap)) { + dev_err(&client->dev, "Failed to register i2c regmap %d\n", + (int)PTR_ERR(regmap)); + return PTR_ERR(regmap); + } indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data)); if (!indio_dev)