From: Dmitry Lifshitz Date: Sun, 12 Jan 2014 13:22:52 +0000 (+0200) Subject: ARM: dts: cm-t3x30: add USB OTG support X-Git-Url: https://git.karo-electronics.de/?a=commitdiff_plain;h=dcb27bee4dbd398e64d1bf8b40b0266b4c8a3fa2;p=linux-beck.git ARM: dts: cm-t3x30: add USB OTG support Add USB OTG support for cm-t3x30 CoMs. Signed-off-by: Dmitry Lifshitz Signed-off-by: Tony Lindgren --- diff --git a/arch/arm/boot/dts/omap3-cm-t3x30.dtsi b/arch/arm/boot/dts/omap3-cm-t3x30.dtsi index cb43929d3618..d00055809e31 100644 --- a/arch/arm/boot/dts/omap3-cm-t3x30.dtsi +++ b/arch/arm/boot/dts/omap3-cm-t3x30.dtsi @@ -32,6 +32,23 @@ OMAP3_CORE1_IOPAD(0x219a, PIN_INPUT_PULLUP | MUX_MODE4) /* uart3_cts_rctx.gpio_163 */ >; }; + + hsusb0_pins: pinmux_hsusb0_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */ + OMAP3_CORE1_IOPAD(0x21a2, PIN_OUTPUT | MUX_MODE0) /* hsusb0_stp.hsusb0_stp */ + OMAP3_CORE1_IOPAD(0x21a4, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_dir.hsusb0_dir */ + OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_nxt.hsusb0_nxt */ + OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data0.hsusb2_data0 */ + OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data1.hsusb0_data1 */ + OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data2.hsusb0_data2 */ + OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data3 */ + OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data4 */ + OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data5 */ + OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data6 */ + OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */ + >; + }; }; &gpmc { @@ -101,3 +118,14 @@ &hsusb2_phy { reset-gpios = <&twl_gpio 7 GPIO_ACTIVE_LOW>; }; + +&usb_otg_hs { + pinctrl-names = "default"; + pinctrl-0 = <&hsusb0_pins>; + interface-type = <0>; + usb-phy = <&usb2_phy>; + phys = <&usb2_phy>; + phy-names = "usb2-phy"; + mode = <3>; + power = <50>; +};