From: William Markezana Date: Thu, 29 Aug 2013 11:51:42 +0000 (+0200) Subject: hwmon: (htu21) Add Measurement Specialties HTU21D support X-Git-Url: https://git.karo-electronics.de/?a=commitdiff_plain;h=f060c658b820141f18abd7b71586d628464a03ea;p=linux-beck.git hwmon: (htu21) Add Measurement Specialties HTU21D support Signed-off-by: William Markezana [Guenter Roeck - minor formatting changes] Signed-off-by: Guenter Roeck --- diff --git a/Documentation/hwmon/htu21 b/Documentation/hwmon/htu21 new file mode 100644 index 000000000000..f39a215fb6ae --- /dev/null +++ b/Documentation/hwmon/htu21 @@ -0,0 +1,46 @@ +Kernel driver htu21 +=================== + +Supported chips: + * Measurement Specialties HTU21D + Prefix: 'htu21' + Addresses scanned: none + Datasheet: Publicly available at the Measurement Specialties website + http://www.meas-spec.com/downloads/HTU21D.pdf + + +Author: + William Markezana + +Description +----------- + +The HTU21D is a humidity and temperature sensor in a DFN package of +only 3 x 3 mm footprint and 0.9 mm height. + +The devices communicate with the I2C protocol. All sensors are set to the +same I2C address 0x40, so an entry with I2C_BOARD_INFO("htu21", 0x40) can +be used in the board setup code. + +This driver does not auto-detect devices. You will have to instantiate the +devices explicitly. Please see Documentation/i2c/instantiating-devices +for details. + +sysfs-Interface +--------------- + +temp1_input - temperature input +humidity1_input - humidity input + +Notes +----- + +The driver uses the default resolution settings of 12 bit for humidity and 14 +bit for temperature, which results in typical measurement times of 11 ms for +humidity and 44 ms for temperature. To keep self heating below 0.1 degree +Celsius, the device should not be active for more than 10% of the time. For +this reason, the driver performs no more than two measurements per second and +reports cached information if polled more frequently. + +Different resolutions, the on-chip heater, using the CRC checksum and reading +the serial number are not supported yet. diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig index 0ff09d8d987b..b3ab9d43bb3e 100644 --- a/drivers/hwmon/Kconfig +++ b/drivers/hwmon/Kconfig @@ -511,6 +511,16 @@ config SENSORS_HIH6130 This driver can also be built as a module. If so, the module will be called hih6130. +config SENSORS_HTU21 + tristate "Measurement Specialties HTU21D humidity/temperature sensors" + depends on I2C + help + If you say yes here you get support for the Measurement Specialties + HTU21D humidity and temperature sensors. + + This driver can also be built as a module. If so, the module + will be called htu21. + config SENSORS_CORETEMP tristate "Intel Core/Core2/Atom temperature sensor" depends on X86 diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile index 4f0fb5235f42..ec7cde06eb52 100644 --- a/drivers/hwmon/Makefile +++ b/drivers/hwmon/Makefile @@ -65,6 +65,7 @@ obj-$(CONFIG_SENSORS_GL518SM) += gl518sm.o obj-$(CONFIG_SENSORS_GL520SM) += gl520sm.o obj-$(CONFIG_SENSORS_GPIO_FAN) += gpio-fan.o obj-$(CONFIG_SENSORS_HIH6130) += hih6130.o +obj-$(CONFIG_SENSORS_HTU21) += htu21.o obj-$(CONFIG_SENSORS_ULTRA45) += ultra45_env.o obj-$(CONFIG_SENSORS_I5K_AMB) += i5k_amb.o obj-$(CONFIG_SENSORS_IBMAEM) += ibmaem.o diff --git a/drivers/hwmon/htu21.c b/drivers/hwmon/htu21.c new file mode 100644 index 000000000000..839086e0e951 --- /dev/null +++ b/drivers/hwmon/htu21.c @@ -0,0 +1,199 @@ +/* + * Measurement Specialties HTU21D humidity and temperature sensor driver + * + * Copyright (C) 2013 William Markezana + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +/* HTU21 Commands */ +#define HTU21_T_MEASUREMENT_HM 0xE3 +#define HTU21_RH_MEASUREMENT_HM 0xE5 + +struct htu21 { + struct device *hwmon_dev; + struct mutex lock; + bool valid; + unsigned long last_update; + int temperature; + int humidity; +}; + +static inline int htu21_temp_ticks_to_millicelsius(int ticks) +{ + ticks &= ~0x0003; /* clear status bits */ + /* + * Formula T = -46.85 + 175.72 * ST / 2^16 from datasheet p14, + * optimized for integer fixed point (3 digits) arithmetic + */ + return ((21965 * ticks) >> 13) - 46850; +} + +static inline int htu21_rh_ticks_to_per_cent_mille(int ticks) +{ + ticks &= ~0x0003; /* clear status bits */ + /* + * Formula RH = -6 + 125 * SRH / 2^16 from datasheet p14, + * optimized for integer fixed point (3 digits) arithmetic + */ + return ((15625 * ticks) >> 13) - 6000; +} + +static int htu21_update_measurements(struct i2c_client *client) +{ + int ret = 0; + struct htu21 *htu21 = i2c_get_clientdata(client); + + mutex_lock(&htu21->lock); + + if (time_after(jiffies, htu21->last_update + HZ / 2) || + !htu21->valid) { + ret = i2c_smbus_read_word_swapped(client, + HTU21_T_MEASUREMENT_HM); + if (ret < 0) + goto out; + htu21->temperature = htu21_temp_ticks_to_millicelsius(ret); + ret = i2c_smbus_read_word_swapped(client, + HTU21_RH_MEASUREMENT_HM); + if (ret < 0) + goto out; + htu21->humidity = htu21_rh_ticks_to_per_cent_mille(ret); + htu21->last_update = jiffies; + htu21->valid = true; + } +out: + mutex_unlock(&htu21->lock); + + return ret >= 0 ? 0 : ret; +} + +static ssize_t htu21_show_temperature(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct i2c_client *client = to_i2c_client(dev); + struct htu21 *htu21 = i2c_get_clientdata(client); + int ret = htu21_update_measurements(client); + if (ret < 0) + return ret; + return sprintf(buf, "%d\n", htu21->temperature); +} + +static ssize_t htu21_show_humidity(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct i2c_client *client = to_i2c_client(dev); + struct htu21 *htu21 = i2c_get_clientdata(client); + int ret = htu21_update_measurements(client); + if (ret < 0) + return ret; + return sprintf(buf, "%d\n", htu21->humidity); +} + +static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, + htu21_show_temperature, NULL, 0); +static SENSOR_DEVICE_ATTR(humidity1_input, S_IRUGO, + htu21_show_humidity, NULL, 0); + +static struct attribute *htu21_attributes[] = { + &sensor_dev_attr_temp1_input.dev_attr.attr, + &sensor_dev_attr_humidity1_input.dev_attr.attr, + NULL +}; + +static const struct attribute_group htu21_group = { + .attrs = htu21_attributes, +}; + +static int htu21_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct htu21 *htu21; + int err; + + if (!i2c_check_functionality(client->adapter, + I2C_FUNC_SMBUS_READ_WORD_DATA)) { + dev_err(&client->dev, + "adapter does not support SMBus word transactions\n"); + return -ENODEV; + } + + htu21 = devm_kzalloc(&client->dev, sizeof(*htu21), GFP_KERNEL); + if (!htu21) + return -ENOMEM; + + i2c_set_clientdata(client, htu21); + + mutex_init(&htu21->lock); + + err = sysfs_create_group(&client->dev.kobj, &htu21_group); + if (err) { + dev_dbg(&client->dev, "could not create sysfs files\n"); + return err; + } + htu21->hwmon_dev = hwmon_device_register(&client->dev); + if (IS_ERR(htu21->hwmon_dev)) { + dev_dbg(&client->dev, "unable to register hwmon device\n"); + err = PTR_ERR(htu21->hwmon_dev); + goto error; + } + + dev_info(&client->dev, "initialized\n"); + + return 0; + +error: + sysfs_remove_group(&client->dev.kobj, &htu21_group); + return err; +} + +static int htu21_remove(struct i2c_client *client) +{ + struct htu21 *htu21 = i2c_get_clientdata(client); + + hwmon_device_unregister(htu21->hwmon_dev); + sysfs_remove_group(&client->dev.kobj, &htu21_group); + + return 0; +} + +static const struct i2c_device_id htu21_id[] = { + { "htu21", 0 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, htu21_id); + +static struct i2c_driver htu21_driver = { + .class = I2C_CLASS_HWMON, + .driver = { + .name = "htu21", + }, + .probe = htu21_probe, + .remove = htu21_remove, + .id_table = htu21_id, +}; + +module_i2c_driver(htu21_driver); + +MODULE_AUTHOR("William Markezana "); +MODULE_DESCRIPTION("MEAS HTU21D humidity and temperature sensor driver"); +MODULE_LICENSE("GPL");