i40e: Never let speed get set to 0 in get_settings
In ethtool, there is a possibility of speed getting set to 0
if advertise is set to 0 (which it is when autoneg is disabled).
We never want this to happen as the firmware will actually attempt
to set the speed to 0 sending link down, so add an extra check
to make sure this doesn't happen.
Change-ID: I62e0eeee2cbf043d8e6f5c9c9f0b92794e877f01 Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Carolyn Wyborny [Wed, 26 Aug 2015 19:14:15 +0000 (15:14 -0400)]
i40e: Fix for truncated interrupt name
This patch extends the size of the text available for the interrupt names.
Without this patch, all the descriptive data available for the Flow
Director interrupts is truncated.
Change-ID: I2ac458f23ac3b4ea8f1edf73edc283b1d3704c7f Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Wed, 26 Aug 2015 19:14:14 +0000 (15:14 -0400)]
i40e/i40evf: assure clean asq status report
There was a possibility where the asq_last_status could get through without
update and thus report a previous error. I don't think we've actually seen
this happen, but this patch will help make sure it doesn't.
Change-ID: I9e33927052a5ee6ea21f80b66d4c4b76c2760b17 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Christopher Pau <christopher.pau@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Wed, 26 Aug 2015 19:14:13 +0000 (15:14 -0400)]
i40e: make i40e_init_pf_fcoe to void
i40e_init_pf_fcoe() didn't return anything except 0, it prints enough
error info already, and no driver logic depends on the return value,
so this can be void.
Change-ID: Ie6afad849857d87a7064c42c3cce14c74c2f29d8 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Wed, 26 Aug 2015 19:14:12 +0000 (15:14 -0400)]
i40e: fix bad CEE status shift value
Fix a shift value that was wrong, ending up with a bad bitmask. Also add
a blank line between two sets of #defines for better readability.
Change-ID: I3e41fa2a2ab904d3a4e6cbf13972ab0036a10601 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Wed, 26 Aug 2015 19:14:10 +0000 (15:14 -0400)]
i40e/i40evf: add driver support for new device ids
Early addition of new a device id.
Change-ID: I61a8c8556fdf4f5714be4e4089689e374f30293c Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Wed, 26 Aug 2015 19:14:09 +0000 (15:14 -0400)]
i40e: stop VF rings
Explicitly stop the rings belonging to each VF when disabling SR-IOV.
Even though the VFs were gone, and the associated VSIs were removed, the
rings were not stopped, and in some circumstances the hardware would
continue to access the memory formerly used by the rings, causing memory
corruption or DMAR errors, both of which would lead to general malaise
of the kernel.
To relieve this condition, explicitly stop all the rings associated with
each VF before releasing its resources.
Change-ID: I78c05d562c66e7b594b7e48d67860f49b3e5b6ec Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Wed, 26 Aug 2015 19:14:08 +0000 (15:14 -0400)]
i40e: enable WoL operation if config bit show WoL capable
The driver was disabling Wake-on-LAN by default and waiting for the user
to expressly turn it on. This patch has the driver turning on WoL from
the start if enabled in the hardware config, which matches the behavior
of our other drivers.
Change-ID: I43faedb907f8ba4d1a61b72a7c86072b97af12b1 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e: Increase the amount of time we wait for reset to be done
In some rare cases the reset can take longer to complete so increase the
amount of time we wait.
Change-ID: Ib5628ec54b526a811ee33d1214fe763226406671 Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Eric Dumazet [Tue, 6 Oct 2015 21:49:58 +0000 (14:49 -0700)]
tcp: ensure prior synack rtx behavior with small backlogs
Some applications use a listen() backlog of 1.
Prior kernels were silently enforcing a qlen_log of 4, so that we were
sending up to /proc/sys/net/ipv4/tcp_synack_retries SYNACK messages.
Fixes: ef547f2ac16b ("tcp: remove max_qlen_log") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 7 Oct 2015 11:52:14 +0000 (04:52 -0700)]
Merge branch 's390-net'
Ursula Braun says:
====================
s390: qeth patches for net-next
here are some s390 related patches for net-next. The qeth patches
are performance optimizations in the driver. The qdio patch corrects
a warning condition.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eugene Crosser [Tue, 6 Oct 2015 13:12:29 +0000 (15:12 +0200)]
s390/qdio: fix WARN_ON_ONCE condition
If HiperSockets Completion Queueing is enabled, qdio always
issues a warning, since the condition is always met.
This patch fixes the condition in WARN_ON_ONCE that was always
true.
Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
s390/qeth: optimize MAC handling in rx_mode callback
In layer2 mode of the qeth driver, MAC address lists
from struct net_device require mapping to the OSA-card.
The existing implementation is inefficient for lists with
more than several MAC addresses, since for every
ndo_set_rx_mode callback it removes all MAC addresses first,
and then registers the current MAC address list.
This patch changes implementation of ndo_set_rx_mode callback
in qeth, only performing hardware registration/removal for
new/deleted addresses. To shorten lookup of MAC addresses
registered addresses are kept in a hashtable instead of a
linear list.
Signed-off-by: Lakhvich Dmitriy <ldmitriy@ru.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Reviewed-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com> Reviewed-by: Thomas Richter <tmricht@de.ibm.com> Tested-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Richter [Tue, 6 Oct 2015 13:12:27 +0000 (15:12 +0200)]
s390/qeth: switch to napi_gro_receive
Add support for GRO (generic receive offload) in the layer 2
part of device driver qeth. This results in a performance
improvement when GRO and RX is turned on.
Signed-off-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 7 Oct 2015 11:49:39 +0000 (04:49 -0700)]
Merge branch 'bridge-netlink-port-attrs'
Nikolay Aleksandrov says:
====================
bridge: netlink: complete port attribute support
This is the second set that completes the bridge port's netlink support and
makes everything from sysfs available via netlink. I've used sysfs as a
guide of what and how to set again. I've tested setting/getting every
option and also this time tested enabling KASAN. Again there're a few long
line warnings about the ifla attribute names in br_port_info_size() but
as the previous set - it's good to know what's been accounted for.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the following attributes in order to export port's timer values:
IFLA_BRPORT_MESSAGE_AGE_TIMER, IFLA_BRPORT_FORWARD_DELAY_TIMER and
IFLA_BRPORT_HOLD_TIMER.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bridge: netlink: export port's topology_change_ack and config_pending
Add IFLA_BRPORT_TOPOLOGY_CHANGE_ACK and IFLA_BRPORT_CONFIG_PENDING to
allow getting port's topology_change_ack and config_pending respectively
via netlink.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 5 Oct 2015 17:49:04 +0000 (10:49 -0700)]
net: Lookup actual route when oif is VRF device
If the user specifies a VRF device in a get route query the custom route
pointing to the VRF device is returned:
$ ip route ls table vrf-red
unreachable default
broadcast 10.2.1.0 dev eth1 proto kernel scope link src 10.2.1.2
10.2.1.0/24 dev eth1 proto kernel scope link src 10.2.1.2
local 10.2.1.2 dev eth1 proto kernel scope host src 10.2.1.2
broadcast 10.2.1.255 dev eth1 proto kernel scope link src 10.2.1.2
$ ip route get oif vrf-red 10.2.1.40
10.2.1.40 dev vrf-red
cache
Add the flags to skip the custom route and go directly to the FIB. With
this patch the actual route is returned:
$ ip route get oif vrf-red 10.2.1.40
10.2.1.40 dev eth1 src 10.2.1.2
cache
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 7 Oct 2015 11:29:18 +0000 (04:29 -0700)]
Merge tag 'mac80211-next-for-davem-2015-10-05' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
For the current cycle, we have the following right now:
* many internal fixes, API improvements, cleanups, etc.
* full AP client state tracking in cfg80211/mac80211 from Ayala
* VHT support (in mac80211) for mesh
* some A-MSDU in A-MPDU support from Emmanuel
* show current TX power to userspace (from Rafał)
* support for netlink dump in vendor commands (myself)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 7 Oct 2015 11:27:51 +0000 (04:27 -0700)]
Merge branch 'l3mdev_saddr_op'
David Ahern says:
====================
net: Add saddr op to l3mdev and vrf
First 2 patches are re-sends of patches that got lost in the ethosphere
Tuesday; they were part of the first round of l3mdev conversions.
Next 3 handle the source address lookup for raw and datagram sockets
bound to a VRF device.
The conversion to the get_saddr op also fixes locally originated TCP
packets showing up at the VRF device. The use of the FLOWI_FLAG_L3MDEV_SRC
flag in ip_route_connect_init was causing locally generated packets
to skip the VRF device.
v2
- rebased to top of net-next per device delete fix and hash based
multipath patches
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 5 Oct 2015 15:51:27 +0000 (08:51 -0700)]
net: Add l3mdev saddr lookup to raw_sendmsg
ping originated on box through a VRF device is showing up in tcpdump
without a source address:
$ tcpdump -n -i vrf-blue
08:58:33.311303 IP 0.0.0.0 > 10.2.2.254: ICMP echo request, id 2834, seq 1, length 64
08:58:33.311562 IP 10.2.2.254 > 10.2.2.2: ICMP echo reply, id 2834, seq 1, length 64
Add the call to l3mdev_get_saddr to raw_sendmsg.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 5 Oct 2015 15:51:26 +0000 (08:51 -0700)]
net: Add source address lookup op for VRF
Add operation to l3mdev to lookup source address for a given flow.
Add support for the operation to VRF driver and convert existing
IPv4 hooks to use the new lookup.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 5 Oct 2015 15:51:25 +0000 (08:51 -0700)]
net: Refactor path selection in __ip_route_output_key_hash
VRF device needs the same path selection following lookup to set source
address. Rather than duplicating code, move existing code into a
function that is exported to modules.
Code move only; no functional change.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 5 Oct 2015 14:32:51 +0000 (08:32 -0600)]
net: Fix vti use case with oif in dst lookups for IPv6
It occurred to me yesterday that 741a11d9e4103 ("net: ipv6: Add
RT6_LOOKUP_F_IFACE flag if oif is set") means that xfrm6_dst_lookup
needs the FLOWI_FLAG_SKIP_NH_OIF flag set. This latest commit causes
the oif to be considered in lookups which is known to break vti. This
explains why 58189ca7b274 did not the IPv6 change at the time it was
submitted.
Fixes: 42a7b32b73d6 ("xfrm: Add oif to dst lookups") Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Claudiu Manoil [Mon, 5 Oct 2015 14:19:59 +0000 (17:19 +0300)]
gianfar: Add WAKE_UCAST and "wake-on-filer" support
This enables eTSEC's filer (Rx parser) and the FGPI Rx
interrupt (Filer General Purpose Interrupt) as a wakeup
source event.
Upon entering suspend state, the eTSEC filer is given
a rule to match incoming L2 unicast packets. A packet
matching the rule will be enqueued in the Rx ring and
a FGPI Rx interrupt will be asserted by the filer to
wakeup the system. Other packet types will be dropped.
On resume the filer table is restored to the content
before entering suspend state.
The set of rules from gfar_filer_config_wol() could be
extended to implement other WoL capabilities as well.
The "fsl,wake-on-filer" DT binding enables this capability
on certain platforms that feature the necessary power
management infrastructure, targeting mainly printing and
imaging applications.
(refer to Power Management section of the SoC Ref Man)
Cc: Li Yang <leoli@freescale.com> Cc: Zhao Chenhui <chenhui.zhao@freescale.com> Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Claudiu Manoil [Mon, 5 Oct 2015 14:19:58 +0000 (17:19 +0300)]
powerpc: dts: p1022si: Add fsl,wake-on-filer for eTSEC
Enable the "wake-on-filer" (aka. wake on user defined packet)
wake on lan capability for the eTSEC ethernet nodes.
Cc: Li Yang <leoli@freescale.com> Cc: Zhao Chenhui <chenhui.zhao@freescale.com> Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Claudiu Manoil [Mon, 5 Oct 2015 14:19:57 +0000 (17:19 +0300)]
doc: dt: net: Add fsl,wake-on-filer for eTSEC
Add the "fsl,wake-on-filer" property for eTSEC nodes to
indicate that the system has the power management
infrastructure needed to be able to wake up the system
via FGPI (filer, aka. h/w rx parser) interrupt.
Cc: Li Yang <leoli@freescale.com> Cc: Zhao Chenhui <chenhui.zhao@freescale.com> Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 7 Oct 2015 11:18:04 +0000 (04:18 -0700)]
Merge branch 'ovs-ipv6-tunnel'
Jiri Benc says:
====================
openvswitch: add IPv6 tunneling support
This builds on the previous work that added IPv6 support to lwtunnels and
adds IPv6 tunneling support to ovs.
To use IPv6 tunneling, there needs to be a metadata based tunnel net_device
created and added to the ovs bridge. Currently, only vxlan is supported by
the kernel, with geneve to follow shortly. There's no need nor intent to add
a support for this into the vport-vxlan (etc.) compat layer.
v3: dropped the last two patches added in v2.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Benc [Mon, 5 Oct 2015 11:09:47 +0000 (13:09 +0200)]
openvswitch: netlink attributes for IPv6 tunneling
Add netlink attributes for IPv6 tunnel addresses. This enables IPv6 support
for tunnels.
Signed-off-by: Jiri Benc <jbenc@redhat.com> Acked-by: Pravin B Shelar <pshelar@nicira.com> Acked-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Benc [Mon, 5 Oct 2015 11:09:46 +0000 (13:09 +0200)]
openvswitch: add tunnel protocol to sw_flow_key
Store tunnel protocol (AF_INET or AF_INET6) in sw_flow_key. This field now
also acts as an indicator whether the flow contains tunnel data (this was
previously indicated by tun_key.u.ipv4.dst being set but with IPv6 addresses
in an union with IPv4 ones this won't work anymore).
The new field was added to a hole in sw_flow_key.
Signed-off-by: Jiri Benc <jbenc@redhat.com> Acked-by: Pravin B Shelar <pshelar@nicira.com> Acked-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
bridge: netlink: make br_fill_info's frame size smaller
When KASAN is enabled the frame size grows > 2048 bytes and we get a
warning, so make it smaller.
net/bridge/br_netlink.c: In function 'br_fill_info':
>> net/bridge/br_netlink.c:1110:1: warning: the frame size of 2160 bytes
>> is larger than 2048 bytes [-Wframe-larger-than=]
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Sat, 3 Oct 2015 18:43:46 +0000 (11:43 -0700)]
net: Add support for filtering neigh dump by device index
Add support for filtering neighbor dumps by device by adding the
NDA_IFINDEX attribute to the dump request.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 7 Oct 2015 10:01:53 +0000 (03:01 -0700)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-10-03
This series contains updates to i40e and i40evf, some of which are to
resolve more Red Hat bugzilla issues.
Jiang Liu updates the i40e and i40evf drivers to use numa_mem_id()
instead of numa_node_id() to get the nearest node with memory which
better supports memoryless nodes.
Anjali fixes an issue from Dan Carpenter <dan.carpenter@oracle.com>,
to resolve a memory leak in X722 RSS configuration path, where we should
free the memory allocated before exiting.
Shannon modifies the drivers to ensure we have the spinlocks before we
clear the ARQ and ASQ management registers. In addition, we widen the
locked portion insert a sanity check to ensure we are working with safe
register values.
Mitch fixes an issue where under certain circumstances, we can get an
extra VF_RESOURCES message from the PF driver at runtime. When this
occurs, we need to parse it because our VSI may have changed and that
will affect the relationship with the PF driver. But this parsing also
blows away our current MAC address, so resolve the issue by restoring
the current MAC address from the netdev struct after we parse the
resource message.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Sat, 3 Oct 2015 17:09:07 +0000 (18:09 +0100)]
net: dsa: better error reporting
Add additional error reporting to the generic DSA code, so it's easier
to debug when things go wrong. This was useful when initially bringing
up 88e6176 on a new board.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Sat, 3 Oct 2015 17:09:01 +0000 (18:09 +0100)]
net: dsa: mv88e6xxx: remove link polling
The link status is polled by the generic phy layer, there's no need to
duplicate that polling with additional polling. This additional polling
adds additional MDIO traffic, and races with the generic phy layer,
resulting in missing or duplicated link status messages.
Tested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Peter Nørlund [Tue, 6 Oct 2015 05:24:47 +0000 (07:24 +0200)]
ipv4: Fix compilation errors in fib_rebalance
This fixes
net/built-in.o: In function `fib_rebalance':
fib_semantics.c:(.text+0x9df14): undefined reference to `__divdi3'
and
net/built-in.o: In function `fib_rebalance':
net/ipv4/fib_semantics.c:572: undefined reference to `__aeabi_ldivmod'
Fixes: 0e884c78ee19 ("ipv4: L3 hash-based multipath") Signed-off-by: Peter Nørlund <pch@ordbogen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Fri, 2 Oct 2015 16:42:00 +0000 (18:42 +0200)]
ebpf: include perf_event only where really needed
Commit ea317b267e9d ("bpf: Add new bpf map type to store the pointer
to struct perf_event") added perf_event.h to the main eBPF header, so
it gets included for all users. perf_event.h is actually only needed
from array map side, so lets sanitize this a bit.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Cc: Kaixu Xia <xiakaixu@huawei.com> Acked-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
The ASIX RX handler algorithm is weak on error handling.
There is a design flaw in the ASIX RX handler algorithm because the
implementation for handling RX Ethernet frames for the DUB-E100 C1 can
have Ethernet frames spanning multiple URBs. This means that payload data
from more than 1 URB is sometimes needed to fill the socket buffer with a
complete Ethernet frame. When the URB with the start of an Ethernet frame
is received then an attempt is made to allocate a socket buffer. If the
memory allocation fails then the algorithm sets the buffer pointer member
to NULL and the function exits (no crash yet). Subsequently, the RX hander
is called again to process the next URB which assumes there is a socket
buffer available and the kernel crashes when there is no buffer.
This patchset implements an improvement to the RX handling algorithm to
avoid a crash when no memory is available for the socket buffer.
The patchset will apply cleanly to the net-next master branch but the
created kernel has not been tested. The driver was tested on ARM kernels
v3.8 and v3.14 for a commercial product.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Dean Jenkins [Fri, 2 Oct 2015 13:29:08 +0000 (14:29 +0100)]
asix: Continue processing URB if no RX netdev buffer
Avoid a loss of synchronisation of the Ethernet Data header 32-bit
word due to a failure to get a netdev socket buffer.
The ASIX RX handling algorithm returned 0 upon a failure to get
an allocation of a netdev socket buffer. This causes the URB
processing to stop which potentially causes a loss of synchronisation
with the Ethernet Data header 32-bit word. Therefore, subsequent
processing of URBs may be rejected due to a loss of synchronisation.
This may cause additional good Ethernet frames to be discarded
along with outputting of synchronisation error messages.
Implement a solution which checks whether a netdev socket buffer
has been allocated before trying to copy the Ethernet frame into
the netdev socket buffer. But continue to process the URB so that
synchronisation is maintained. Therefore, only a single Ethernet
frame is discarded when no netdev socket buffer is available.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com> Signed-off-by: Mark Craske <Mark_Craske@mentor.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dean Jenkins [Fri, 2 Oct 2015 13:29:07 +0000 (14:29 +0100)]
asix: On RX avoid creating bad Ethernet frames
When RX Ethernet frames span multiple URB socket buffers,
the data stream may suffer a discontinuity which will cause
the current Ethernet frame in the netdev socket buffer
to be incomplete. This frame needs to be discarded instead
of appending unrelated data from the current URB socket buffer
to the Ethernet frame in the netdev socket buffer. This avoids
creating a corrupted Ethernet frame in the netdev socket buffer.
A discontinuity can occur when the previous URB socket buffer
held an incomplete Ethernet frame due to truncation or a
URB socket buffer containing the end of the Ethernet frame
was missing.
Therefore, add a sanity test for when an Ethernet frame
spans multiple URB socket buffers to check that the remaining
bytes of the currently received Ethernet frame point to
a good Data header 32-bit word of the next Ethernet
frame. Upon error, reset the remaining bytes variable to
zero and discard the current netdev socket buffer.
Assume that the Data header is located at the start of
the current socket buffer and attempt to process the next
Ethernet frame from there. This avoids unnecessarily
discarding a good URB socket buffer that contains a new
Ethernet frame.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com> Signed-off-by: Mark Craske <Mark_Craske@mentor.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The code is checking that the Ethernet frame will fit into a
netdev allocated socket buffer within the constraints of MTU size,
Ethernet header length plus VLAN header length.
The original code was checking rx->remaining each loop of the while
loop that processes multiple Ethernet frames per URB and/or Ethernet
frames that span across URBs. rx->remaining decreases per while loop
so there is no point in potentially checking multiple times that the
Ethernet frame (remaining part) will fit into the netdev socket buffer.
The modification checks that the size of the Ethernet frame will fit
the netdev socket buffer before allocating the netdev socket buffer.
This avoids grabbing memory and then deciding that the Ethernet frame
is too big and then freeing the memory.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com> Signed-off-by: Mark Craske <Mark_Craske@mentor.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dean Jenkins [Fri, 2 Oct 2015 13:29:05 +0000 (14:29 +0100)]
asix: Tidy-up 32-bit header word synchronisation
Tidy-up the Data header 32-bit word synchronisation logic in
asix_rx_fixup_internal() by removing redundant logic tests.
The code is looking at the following cases of the Data header
32-bit word that is present before each Ethernet frame:
a) all 32 bits of the Data header word are in the URB socket buffer
b) first 16 bits of the Data header word are at the end of the URB
socket buffer
c) last 16 bits of the Data header word are at the start of the URB
socket buffer eg. split_head = true
Note that the lifetime of rx->split_head exists outside of the
function call and is accessed per processing of each URB. Therefore,
split_head being true acts on the next URB to be processed.
To check for b) the offset will be 16 bits (2 bytes) from the end of
the buffer then indicate split_head is true.
To check for c) split_head must be true because the first 16 bits
have been found.
To check for a) else c)
Note that the || logic of the old code included the state
(skb->len - offset == sizeof(u16) && rx->split_head) which is not
possible because the split_head cannot be true whilst checking for b).
This is because the split_head indicates that the first 16 bits have
been found and that is not possible whilst checking for the first 16
bits. Therefore simplify the logic.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com> Signed-off-by: Mark Craske <Mark_Craske@mentor.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dean Jenkins [Fri, 2 Oct 2015 13:29:04 +0000 (14:29 +0100)]
asix: Rename remaining and size for clarity
The Data header synchronisation is easier to understand
if the variables "remaining" and "size" are renamed.
Therefore, the lifetime of the "remaining" variable exists
outside of asix_rx_fixup_internal() and is used to indicate
any remaining pending bytes of the Ethernet frame that need
to be obtained from the next socket buffer. This allows an
Ethernet frame to span across multiple socket buffers.
"size" is now local to asix_rx_fixup_internal() and contains
the size read from the Data header 32-bit word.
Add "copy_length" to hold the number of the Ethernet frame
bytes (maybe a part of a full frame) that are to be copied
out of the socket buffer.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com> Signed-off-by: Mark Craske <Mark_Craske@mentor.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Fri, 2 Oct 2015 13:17:33 +0000 (15:17 +0200)]
bpf, seccomp: prepare for upcoming criu support
The current ongoing effort to dump existing cBPF seccomp filters back
to user space requires to hold the pre-transformed instructions like
we do in case of socket filters from sk_attach_filter() side, so they
can be reloaded in original form at a later point in time by utilities
such as criu.
To prepare for this, simply extend the bpf_prog_create_from_user()
API to hold a flag that tells whether we should store the original
or not. Also, fanout filters could make use of that in future for
things like diag. While fanout filters already use bpf_prog_destroy(),
move seccomp over to them as well to handle original programs when
present.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Cc: Tycho Andersen <tycho.andersen@canonical.com> Cc: Pavel Emelyanov <xemul@parallels.com> Cc: Kees Cook <keescook@chromium.org> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Alexei Starovoitov <ast@plumgrid.com> Tested-by: Tycho Andersen <tycho.andersen@canonical.com> Acked-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 93a7e7e837af ("net: Remove the now unused vrf_ptr") Cc: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Ringle [Thu, 1 Oct 2015 11:43:21 +0000 (07:43 -0400)]
net: Microchip encx24j600 driver
This ethernet driver supports the Micorchip enc424j600/626j600 Ethernet
controller over a SPI bus interface. This driver makes use of the regmap API to
optimize access to registers by caching registers where possible.
Jon Ringle [Thu, 1 Oct 2015 11:43:20 +0000 (07:43 -0400)]
regmap: Allow installing custom reg_update_bits function
This commit allows installing a custom reg_update_bits function for cases where
the hardware provides a mechanism to set or clear register bits without a
read/modify/write cycle. Such is the case with the Microchip ENCX24J600.
Signed-off-by: Jon Ringle <jringle@gridpoint.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The current code invokes hang reset in case of error interrupt. We should
hang reset only in case of tx timeout. This because of the way hang reset
is implemented in firmware. Hang reset takes more firmware resources than
soft reset. Adaptor does not generate error interrupt in case of tx
timeout.
Hang reset only in case of tx timeout, in .ndo_tx_timeout. Do soft reset
otherwise. Introduce deferred work, enic_tx_hang_reset, to do hang reset.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the enic adaptors are know to generate spurious interrupts. When
error interrupt is generated, driver just resets the device. This patch
resets the device only when an error is occurred.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 5 Oct 2015 10:48:45 +0000 (03:48 -0700)]
Merge branch 'cxgb4-next'
Hariprasad Shenai says:
====================
cxgb4: Trivial fixes for cxgb4
Fixes the following issues
Don't read non existent T4/T5/T6 adapter registers for ethtool dump.
For T4, dont read mailbox control registers. Adds new devlog faility and
report correct link speed for unsupported ones.
This patch series has been created against net-next tree and includes
patches on cxgb4 driver.
We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.
====================
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4: Report correct link speed for unsupported ones
When we get garbage from the firmware with weird Port Speeds,
etc. we should emit a warning regarding unsupported speeds rather than
use the bogus default of "10Mbps" which isn't even an option in the
firmware Port Information message
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4: Adds a new Device Log Facility FW_DEVLOG_FACILITY_CF
The firmware team added a new Device Log Facility FW_DEVLOG_FACILITY_CF,
but the driver has been decoding Device Log messages with that Facility as
"(NULL)", fixing it.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 5 Oct 2015 10:39:31 +0000 (03:39 -0700)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/net-next
Eric W. Biederman says:
====================
net: Pass net through ip fragmention
This is the next installment of my work to pass struct net through the
output path so the code does not need to guess how to figure out which
network namespace it is in, and ultimately routes can have output
devices in another network namespace.
This round focuses on passing net through ip fragmentation which we seem
to call from about everywhere. That is the main ip output paths, the
bridge netfilter code, and openvswitch. This has to happend at once
accross the tree as function pointers are involved.
First some prep work is done, then ipv4 and ipv6 are converted and then
temporary helper functions are removed.
====================
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
A 3-part patchset that (a) improves current RDS-TCP perf
by 2X-3X and (b) refactors earlier robustness code for
better observability/scaling.
Patch 1 is an enhancment of earlier robustness fixes
that had used separate sockets for client and server endpoints to
resolve race conditions. It is possible to have an equivalent
solution that does not use 2 sockets. The benefit of a
single socket solution is that it results in more predictable
and observable behavior for the underlying TCP pipe of an
RDS connection
Patches 2 and 3 are simple, straightforward perf bug fixes
that align the RDS TCP socket with other parts of the kernel stack.
v2: fix kbuild-test-robot warnings, comments from Sergei Shtylov
and Santosh Shilimkar.
====================
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
RDS-TCP: Set up MSG_MORE and MSG_SENDPAGE_NOTLAST as appropriate in rds_tcp_xmit
For the same reasons as commit 2f5338442425 ("tcp: allow splice() to
build full TSO packets") and commit 35f9c09fe9c7 ("tcp: tcp_sendpages()
should call tcp_push() once"), rds_tcp_xmit may have multiple pages to
send, so use the MSG_MORE and MSG_SENDPAGE_NOTLAST as hints to
tcp_sendpage()
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
RDS-TCP: Do not bloat sndbuf/rcvbuf in rds_tcp_tune
Using the value of RDS_TCP_DEFAULT_BUFSIZE (128K)
clobbers efficient use of TSO because it inflates the size_goal
that is computed in tcp_sendmsg/tcp_sendpage and skews packet
latency, and the default values for these parameters actually
results in significantly better performance.
In request-response tests using rds-stress with a packet size of
100K with 16 threads (test parameters -q 100000 -a 256 -t16 -d16)
between a single pair of IP addresses achieves a throughput of
6-8 Gbps. Without this patch, throughput maxes at 2-3 Gbps under
equivalent conditions on these platforms.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
RDS: Use a single TCP socket for both send and receive.
Commit f711a6ae062c ("net/rds: RDS-TCP: Always create a new rds_sock
for an incoming connection.") modified rds-tcp so that an incoming SYN
would ignore an existing "client" TCP connection which had the local
port set to the transient port. The motivation for ignoring the existing
"client" connection in f711a6ae was to avoid race conditions and an
endless duel of reconnect attempts triggered by a restart/abort of one
of the nodes in the TCP connection.
However, having separate sockets for active and passive sides
is avoidable, and the simpler model of a single TCP socket for
both send and receives of all RDS connections associated with
that tcp socket makes for easier observability. We avoid the race
conditions from f711a6ae by attempting reconnects in rds_conn_shutdown
if, and only if, the (new) c_outgoing bit is set for RDS_TRANS_TCP.
The c_outgoing bit is initialized in __rds_conn_create().
A side-effect of re-using the client rds_connection for an incoming
SYN is the potential of encountering duelling SYNs, i.e., we
have an outgoing RDS_CONN_CONNECTING socket when we get the incoming
SYN. The logic to arbitrate this criss-crossing SYN exchange in
rds_tcp_accept_one() has been modified to emulate the BGP state
machine: the smaller IP address should back off from the connection attempt.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following patches are included in this driver update series:
- Remove unneeded semi-colon
- Follow the DT/ACPI precedence used by the device_ APIs
- Add ethtool support for getting and setting the msglevel
- Add ethtool support error and debug messages
- Simplify the hardware FIFO assignment calculations
- Add receive buffer unavailable statistic
- Use the device workqueue instead of the system workqueue
- Remove the use of a link state bit
This patch series is based on net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Lendacky, Thomas [Wed, 30 Sep 2015 13:53:22 +0000 (08:53 -0500)]
amd-xgbe: Remove the XGBE_LINK state bit
The XGBE_LINK bit is used just to determine whether to call the
netif_carrier_on/off functions. Rather than define and use this bit,
just call the functions. The netif_carrier_ok function can be used in
place of checking the XGBE_LINK bit in the future.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lendacky, Thomas [Wed, 30 Sep 2015 13:53:16 +0000 (08:53 -0500)]
amd-xgbe: Use device workqueue instead of system workqueue
The driver creates, flushes and destroys a device workqueue but queues
work to the system workqueue. Switch from using the system workqueue to
the device workqueue.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Add a statistic that tracks how many times an interrupt is generated for
a receive buffer not being available to the hardware which prevents the
hardware from being able to DMA the received data.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lendacky, Thomas [Wed, 30 Sep 2015 13:53:03 +0000 (08:53 -0500)]
amd-xgbe: Simplify calculation and setting of queue fifos
The calculation of the Tx and Rx fifo sizes can be calculated rather
than hardcoded in a switch statement. Additionally, the per-queue fifo
sizes can be calculated rather than hardcoded using if/else if statements
that can possibly underutilize the available fifo area.
Change the code to calculate the fifo sizes and the per-queue fifo sizes
to simplify the code and make best use of the available fifo.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lendacky, Thomas [Wed, 30 Sep 2015 13:52:57 +0000 (08:52 -0500)]
amd-xgbe: Add ethtool error and debug messages
Add error and dynamic debug messages to various ethtool functions in
the driver while also removing the DBGPR debug print calls. Also, change
the message level for some error messages from alert to err.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lendacky, Thomas [Wed, 30 Sep 2015 13:52:45 +0000 (08:52 -0500)]
amd-xgbe: Use proper DT / ACPI precedence checking
Device tree presence takes precedence over ACPI in the device_* APIs.
The amd-xgbe driver should follow the same precedence. Update the check
on whether to use DT / ACPI to follow this.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lendacky, Thomas [Wed, 30 Sep 2015 13:52:38 +0000 (08:52 -0500)]
amd-xgbe: Remove an unneeded semicolon on a switch statement
Remove an unneeded semicolon at the end of a switch statement block.
Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 30 Sep 2015 13:18:23 +0000 (06:18 -0700)]
tcp: restore fastopen operations
I accidentally cleared fastopenq.max_qlen in reqsk_queue_alloc()
while max_qlen can be set before listen() is called,
using TCP_FASTOPEN socket option for example.
Fixes: 0536fcc039a8 ("tcp: prepare fastopen code for upcoming listener changes") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 5 Oct 2015 10:16:49 +0000 (03:16 -0700)]
Merge branch 'net-y2038'
Arnd Bergmann says:
====================
net: assorted y2038 changes
This is a set of changes for network drivers and core code to
get rid of the use of time_t and derived data structures.
I have a longer set of patches that enables me to build kernels
with the time_t definition removed completely as a help to find
y2038 overflow issues. This is the subset for networking that
contains all code that has a reasonable way of fixing at the
moment and that is either commonly used (in one of the defconfigs)
or that blocks building a whole subsystem.
Most of the patches in this series should be noncontroversial,
but the last two that I marked [RFC] are a bit tricky and
need input from people that are more familiar with the code than
I am. All 12 patches are independent of one another and can
be applied in any order, so feel free to pick all that look
good.
Patches that are not included here are:
- disabling less common device drivers that I don't have a fix
for yet, this includes
drivers/net/ethernet/brocade/bna/bfa_ioc.c
drivers/net/ethernet/qlogic/netxen/netxen_nic_hw.c
drivers/net/ethernet/tile/tilegx.c
drivers/net/hamradio/baycom_ser_fdx.c
drivers/net/wireless/ath/ath10k/core.h
drivers/net/wireless/ath/ath9k/
drivers/net/wireless/ath/ath9k/
drivers/net/wireless/atmel.c
drivers/net/wireless/prism54/isl_38xx.c
drivers/net/wireless/rt2x00/rt2x00debug.c
drivers/net/wireless/rtlwifi/
drivers/net/wireless/ti/wlcore/
drivers/staging/ozwpan/
net/atm/mpoa_caches.c
net/atm/mpoa_proc.c
net/dccp/probe.c
net/ipv4/tcp_probe.c
net/netfilter/nfnetlink_queue_core.c
net/netfilter/nfnetlink_queue_core.c
net/netfilter/xt_time.c
net/openvswitch/flow.c
net/sctp/probe.c
net/sunrpc/auth_gss/
net/sunrpc/svcauth_unix.c
net/vmw_vsock/af_vsock.c
We'll get there eventually, or we an add a dependency to ensure
they are not built on 32-bit kernels that need to survive
beyond 2038. Most of these should be really easy to fix.
- recvmmsg/sendmmsg system calls: patches have been sent out
as part of the syscall series, need a little more work and
review
- SIOCGSTAMP/SIOCGSTAMPNS/ ioctl calls: tricky, need to discuss
with some folks at kernel summit
- SO_RCVTIMEO/SO_SNDTIMEO/SO_TIMESTAMP/SO_TIMESTAMPNS socket
opt: similar and related to the ioctl
- mmapped packet socket: need to create v4 of the API, nontrivial
- pktgen: sends 32-bit timestamps over network, need to find out
if using unsigned stamps is good enough
- af_rxpc: similar to pktgen, uses 32-bit times for deadlines
- ppp ioctl: patch is being worked on, nontrivial but doable
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to avoid using time_t in the kernel because of the y2038
overflow problem. The use in sctp is not for storing seconds at
all, but instead uses microseconds and is passed as 32-bit
on all machines.
This patch changes the type to u32, which better fits the use.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Vlad Yasevich <vyasevich@gmail.com> Cc: Neil Horman <nhorman@tuxdriver.com> Cc: linux-sctp@vger.kernel.org Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The ipv6 mip6 implementation is one of only a few users of the
skb_get_timestamp() function in the kernel, which is both unsafe
on 32-bit architectures because of the 2038 overflow, and slightly
less efficient than the skb_get_ktime() based approach.
This converts the function call and the mip6_report_rate_limiter
structure that stores the time stamp, eliminating all uses of
timeval in the ipv6 code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Cc: James Morris <jmorris@namei.org> Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> Cc: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
The __build_packet_message function fills a nfulnl_msg_packet_timestamp
structure that uses 64-bit seconds and is therefore y2038 safe, but
it uses an intermediate 'struct timespec' which is not.
This trivially changes the code to use 'struct timespec64' instead,
to correct the result on 32-bit architectures.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Pablo Neira Ayuso <pablo@netfilter.org> Cc: Patrick McHardy <kaber@trash.net> Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu> Cc: netfilter-devel@vger.kernel.org Cc: coreteam@netfilter.org Acked-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
The zatm_t_hist structure is not used anywhere in the kernel, but is
exported to user space. As we are trying to eliminate uses of time_t
in the kernel for y2038 compatibility, the current definition triggers
checking tools because it contains 'struct timeval'.
As pointed out by Chas Williams, the only user of this structure was
the ZATM_GETHIST ioctl command that has been removed a long time ago,
and we can remove the structure as well without breaking any user
space.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Chas Williams <3chas3@gmail.com> Cc: linux-atm-general@lists.sourceforge.net Signed-off-by: David S. Miller <davem@davemloft.net>
The mac80211 code uses ktime_get_ts to measure the connected time.
As this uses monotonic time, it is y2038 safe on 32-bit systems,
but we still want to deprecate the use of 'timespec' because most
other users are broken.
This changes the code to use ktime_get_seconds() instead, which
avoids the timespec structure and is slightly more efficient.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: linux-wireless@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
mwifiex: avoid gettimeofday in ba_threshold setting
mwifiex_get_random_ba_threshold() uses a complex homegrown implementation
to generate a pseudo-random number from the current time as returned
from do_gettimeofday().
This currently requires two 32-bit divisions plus a couple of other
computations that are eventually discarded as only eight bits of
the microsecond portion are used at all.
We could replace this with a call to get_random_bytes(), but that
might drain the entropy pool too fast if this is called for each
packet.
Instead, this patch converts it to use ktime_get_ns(), which is a
bit faster than do_gettimeofday(), and then uses a similar algorithm
as before, but in a way that takes both the nanosecond and second
portion into account for slightly-more-but-still-not-very-random
pseudorandom number.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Amitkumar Karwar <akarwar@marvell.com> Cc: Nishant Sarmukadam <nishants@marvell.com> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: linux-wireless@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
The mwifiex_11n_aggregate_pkt() function creates a ktime_t from
a timeval returned by do_gettimeofday, which is slow and causes
an overflow in 2038 on 32-bit architectures.
This solves both problems by using the appropriate ktime_get_real()
function.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Amitkumar Karwar <akarwar@marvell.com> Cc: Nishant Sarmukadam <nishants@marvell.com> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: linux-wireless@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
We want to deprecate the use of 'struct timespec' on 32-bit
architectures, as it is will overflow in 2038. The igb
driver uses it to read the current time, and can simply
be changed to use ktime_get_real_ts64() instead.
Because of hardware limitations, there is still an overflow
in year 2106, which we cannot really avoid, but this documents
the overflow.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: intel-wired-lan@lists.osuosl.org Reviewed-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
We want to deprecate the use of 'struct timespec' on 32-bit
architectures, as it is will overflow in 2038. The stmmac
driver uses it to read the current time, and can simply
be changed to use ktime_get_real_ts64() instead.
Because of hardware limitations, there is still an overflow
in year 2106, which we cannot really avoid, but this documents
the overflow.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Richard Cochran <richardcochran@gmail.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The fec_ptp_enable_pps uses an open-coded implementation of ns_to_timespec,
which will be removed eventually as it is not y2038-safe on 32-bit
architectures. Two more instances of the same code in this file were
already converted to use the safe ns_to_timespec64 in commit 6630514fcee
("ptp: fec: use helpers for converting ns to timespec"), this changes
the last one as well.
The seconds portion here is actually unused and we could just remove the
timespec variable, but using ns_to_timespec64 can still be better as the
implementation can be hand-optimized in the future.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Fugang Duan <b38611@freescale.com> Cc: Luwei Zhou <b45643@freescale.com> Cc: Frank Li <Frank.Li@freescale.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When the routing cache was removed in 3.6, the IPv4 multipath algorithm changed
from more or less being destination-based into being quasi-random per-packet
scheduling. This increases the risk of out-of-order packets and makes it
impossible to use multipath together with anycast services.
This patch series replaces the old implementation with flow-based load
balancing based on a hash over the source and destination addresses.
Distribution of the hash is done with thresholds as described in RFC 2992.
This reduces the disruption when a path is added/remove when having more than
two paths.
To futher the chance of successful usage in conjuction with anycast, ICMP
error packets are hashed over the inner IP addresses. This ensures that PMTU
will work together with anycast or load-balancers such as IPVS.
Port numbers are not considered since fragments could cause problems with
anycast and IPVS. Relying on the DF-flag for TCP packets is also insufficient,
since ICMP inspection effectively extracts information from the opposite
flow which might have a different state of the DF-flag. This is also why the
RSS hash is not used. These are typically based on the NDIS RSS spec which
mandates TCP support.
Measurements of the additional overhead of a two-path multipath
(p_mkroute_input excl. __mkroute_input) on a Xeon X3550 (4 cores, 2.66GHz):
Original per-packet: ~394 cycles/packet
L3 hash: ~76 cycles/packet
Changes in v5:
- Fixed compilation error
Changes in v4:
- Functions take hash directly instead of func ptr
- Added inline hash function
- Added dummy macros to minimize ifdefs
- Use upper 31 bits of hash instead of lower
Changes in v3:
- Multipath algorithm is no longer configurable (always L3)
- Added random seed to hash
- Moved ICMP inspection to isolated function
- Ignore source quench packets (deprecated as per RFC 6633)
Changes in v2:
- Replaced 8-bit xor hash with 31-bit jenkins hash
- Don't scale weights (since 31-bit)
- Avoided unnecesary renaming of variables
- Rely on DF-bit instead of fragment offset when checking for fragmentation
- upper_bound is now inclusive to avoid overflow
- Use a callback to postpone extracting flow information until necessary
- Skipped ICMP inspection entirely with L4 hashing
- Handle newly added sysctl ignore_routes_with_linkdown
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Peter Nørlund [Wed, 30 Sep 2015 08:12:22 +0000 (10:12 +0200)]
ipv4: ICMP packet inspection for multipath
ICMP packets are inspected to let them route together with the flow they
belong to, minimizing the chance that a problematic path will affect flows
on other paths, and so that anycast environments can work with ECMP.
Signed-off-by: Peter Nørlund <pch@ordbogen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log