Kumar Gala [Thu, 4 Aug 2011 08:13:10 +0000 (03:13 -0500)]
drivers/serial/ucc_uart.c: Fix compiler warning
drivers/tty/serial/ucc_uart.c: In function 'qe2cpu_addr':
drivers/tty/serial/ucc_uart.c:238:2: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'dma_addr_t'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Timur Tabi <timur@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pavan Savoy [Wed, 10 Aug 2011 15:18:37 +0000 (10:18 -0500)]
drivers:misc: ti-st: fix unexpected UART close
If suppose the UIM were to die and hence UART were to close when the
Bluetooth/FM or GPS is turned on, prep the ST for a state where-in if
the UIM comes back up, Bluetooth/FM/GPS can be turned on.
Pavan Savoy [Wed, 10 Aug 2011 15:18:36 +0000 (10:18 -0500)]
drivers:misc: ti-st: free skb on firmware download
If during validation of the firmware download the data doesn't match what is
expected out of the chip, this calls for a firmware download failure and a
retry.
Free the SKB which collects response during such scenarios.
Pavan Savoy [Wed, 10 Aug 2011 15:18:35 +0000 (10:18 -0500)]
drivers:misc: ti-st: wait for completion at fail
When the line discipline install fails for reasons such as missing user-space
UIM or broken communication between UIM and ST driver, then the ST
attempts/retries to request for ldisc installation again.
Pavan Savoy [Wed, 10 Aug 2011 15:18:34 +0000 (10:18 -0500)]
drivers:misc: ti-st: reinit completion before send
download firmware behaves differently at different times, when logs are
enabled and the system is loaded, the wait_for_completion is able to wait for
every send, However during other times the wait does not happen.
So, for reliability reinitializing the completion before every send, makes
sure the wait happens for every send.
Vijay Badawadagi [Wed, 10 Aug 2011 15:18:33 +0000 (10:18 -0500)]
drivers:misc: ti-st: fail-safe on wrong pkt type
Texas Instrument's shared transport driver interpret incoming data from the
UART based on the various protocol drivers registered to the driver such as
btwilink driver or FM or GPS driver which provide logical channel IDs.
In case of bad-behavior from chip such as HCI Event response for a GPS command
or a HCI Event (h/w error event) for a FM response & In case of bad-behavior
from UART driver such as dropping data bytes a fail-safe is required to avoid
kernel panic.
Pavan Savoy [Wed, 10 Aug 2011 15:18:32 +0000 (10:18 -0500)]
drivers:misc: ti-st: reinit completion on ver read
After the version information has been read, the completion which assists in
wait_for_completion during the firmware send/wait sequence is being re-used
and hence this needs to be re-initialised for fool proof firmware download
retries.
Pavan Savoy [Wed, 10 Aug 2011 15:18:31 +0000 (10:18 -0500)]
drivers:misc:ti-st: platform hooks for chip states
Certain platform specific or Host-WiLink Interface specific actions would be
required to be taken when the chip is being enabled and after the chip is
disabled such as configuration of the mux modes for the GPIO of host connected
to the nshutdown of the chip or relinquishing UART after the chip is disabled.
Similar actions can also be taken when the chip is in deep sleep or when the
chip is awake. Performance enhancements such as configuring the host to run
faster when chip is awake and slower when chip is asleep can also be made
here.
Pavan Savoy [Wed, 10 Aug 2011 15:18:30 +0000 (10:18 -0500)]
drivers:misc: ti-st: avoid a misleading dbg msg
Previously the private data of each protocol registered to use ST was
used to determine whether the protocol was registered to use shared
transport or otherwise.
However, now a flag is_registered is maintained to identify whether a
protocol intends to use ST.
Upon closing of the UART the error message relevant to this lack of
un-registration was misleading and this patch fixes that.
base/devres.c: quiet sparse noise about context imbalance
devres_release_all and devres_release_group both aquire the lock
&dev->devres_lock but the release of that lock is done in release_nodes.
This results in sparse noise about context imbalance.
Add a lock annotation to release_nodes to quiet this noise.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Heiko Carstens [Tue, 2 Aug 2011 08:08:34 +0000 (10:08 +0200)]
pti: add missing CONFIG_PCI dependency
allmodconfig compile fails on s390 because of the new PTI driver:
drivers/misc/pti.c:407:3: error: implicit declaration of function 'pci_iounmap'
drivers/misc/pti.c:410:3: error: implicit declaration of function 'pci_release_region'
Add a 'depends on PCI' statement so it doesn't get compiled.
Andrew Bird [Tue, 16 Aug 2011 23:20:03 +0000 (00:20 +0100)]
USB option driver K3765/K4505 avoid CDC_DATA interface
Currently the Option driver avoids binding interface 1 on Huawei K3765
and K4505 broadband modems as it should be handled by the cdc_ether
driver instead. This patch ensures we don't bind the interface 2
on those devices as that is CDC_DATA.
Wang Zhi [Wed, 17 Aug 2011 02:39:31 +0000 (10:39 +0800)]
USB: EHCI: Do not rely on PORT_SUSPEND to stop USB resuming in ehci_bus_resume().
From EHCI Spec p.28 HC should clear PORT_SUSPEND when SW clears
PORT_RESUME. In Intel Oaktrail platform, MPH (Multi-Port Host
Controller) core clears PORT_SUSPEND directly when SW sets PORT_RESUME
bit. If we rely on PORT_SUSPEND bit to stop USB resume, we will miss
the action of clearing PORT_RESUME. This will cause unexpected long
resume signal on USB bus.
Signed-off-by: Wang Zhi <zhi.wang@windriver.com> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Andrew Bird [Tue, 16 Aug 2011 19:58:21 +0000 (13:58 -0600)]
USB option driver add PID of Huawei Vodafone K4605
This patch adds the product ID of Huawei's Vodafone K4605 mobile broadband
modem to option.c. This is necessary so that the driver gets loaded on
demand without the intervention of usb_modeswitch. This has the benefit of
it becoming available faster and also ensures that the option driver is not
bound to a network interface that should be claimed by suitable network
driver.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk> Signed-off-by: Alex Chiang <achiang@canonical.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Andrew Bird [Tue, 16 Aug 2011 19:57:14 +0000 (13:57 -0600)]
USB option driver add PID of Huawei Vodafone K3806
This patch adds the product ID of Huawei's Vodafone K3806 mobile broadband
modem to option.c. This is necessary so that the driver gets loaded on
demand without the intervention of usb_modeswitch. This has the benefit of
it becoming available faster and also ensures that the option driver is not
bound to a network interface that should be claimed by cdc_ether.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk> Signed-off-by: Alex Chiang <achiang@canonical.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Merge branch 'for-usb-linus' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
* 'for-usb-linus' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/sarah/xhci:
xhci: Handle zero-length isochronous packets.
USB: Avoid NULL pointer deref in usb_hcd_alloc_bandwidth.
xhci: Remove TDs from TD lists when URBs are canceled.
xhci: Fix failed enqueue in the middle of isoch TD.
xhci: Fix memory leak during failed enqueue.
xHCI: report USB2 port in resuming as suspend
xHCI: fix port U3 status check condition
Linus Torvalds [Mon, 22 Aug 2011 18:25:44 +0000 (11:25 -0700)]
Merge branch 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
* 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/tracing: Fix tracing config option properly
xen: Do not enable PV IPIs when vector callback not present
xen/x86: replace order-based range checking of M2P table by linear one
xen: xen-selfballoon.c needs more header files
David Woodhouse [Fri, 19 Aug 2011 20:14:47 +0000 (22:14 +0200)]
bcma: add uevent to the bus, to autoload drivers
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Acked-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw: Fix STA (AR9485) bringup issue due to incorrect MAC address
Due to some recent optimization done in the way the mac address
bytes are written into the OTP memory, some AR9485 chipsets were
forced to use the first byte from the eeprom template and the
remaining bytes are read from OTP.
AR9485 happens to use generic eeprom template which has 0x1 as
the first byte causes issues in bringing up the card.
So fixed the eeprom template accordingly to address the issue.
Cc: stable@kernel.org Cc: Paul Stewart <pstew@google.com> Signed-off-by: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00: do not drop usb dev reference counter on suspend
When hibernating ->resume may not be called by usb core, but disconnect
and probe instead, so we do not increase the counter after decreasing
it in ->supend. As a result we free memory early, and get crash when
unplugging usb dongle.
Cc: stable@kernel.org Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Input: ad714x - read the interrupt status registers in a row
The interrupt status registers should be read in row to avoid invalid data.
Alter "read" method for both bus options to allow reading several registers
in a row and make sure we read interrupt status registers properly.
Read sequence saves 50% of bus transactions compared to single register
reads. So use it also for the result registers, which are also located
in a row.
Also update copyright notice.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Dmitry Torokhov [Mon, 22 Aug 2011 16:45:39 +0000 (09:45 -0700)]
Input: ad714x - use DMA-safe buffers for spi_write()
spi_write() requires use of DMA-safe (cacheline aligned) buffers.
Also use the same buffers when reading data since to avoid extra
locking and potential memory allocation in spi_write_then_read().
Acked-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This change replaced the SMP operations with event based handlers without
taking into account that this only works when the hypervisor supports
callback vectors. This causes unexplainable hangs early on boot for
HVM guests with more than one CPU.
BugLink: http://bugs.launchpad.net/bugs/791850 CC: stable@kernel.org Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com> Tested-and-Reported-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Linus Walleij [Mon, 22 Aug 2011 07:45:15 +0000 (08:45 +0100)]
ARM: 7045/1: mach-lpc32xx: break out GPIO driver specifics
The <mach/gpio.h> file is included from upper directories
and deal with generic GPIO and gpiolib stuff. Break out the
platform and driver specific defines and functions into its own
header file.
Cc: Wolfram Sang <w.sang@pengutronix.de> Cc: Barry Song <bs14@csr.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Walleij [Mon, 22 Aug 2011 07:44:45 +0000 (08:44 +0100)]
ARM: 7044/1: mach-lpc32xx: move LPC32XX GPIO driver to GPIO subsystem
As per example from the other ARM boards, push the LPC32XX
GPIO driver down to the GPIO subsystem so it can be consolidated.
Cc: Wolfram Sang <w.sang@pengutronix.de> Cc: Barry Song <bs14@csr.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Walleij [Mon, 22 Aug 2011 07:44:18 +0000 (08:44 +0100)]
ARM: 7043/1: mach-ixp2000: rename GPIO header
The ixp2000 abuses the <mach/gpio.h> namespace by not implementing
any generic GPIO nor gpiolib functions in it - just custom GPIO.
Rename the header to <mach/gpio-ixp2000.h> for clarity.
Cc: Lennert Buytenhek <kernel@wantstofly.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Walleij [Mon, 22 Aug 2011 07:43:04 +0000 (08:43 +0100)]
ARM: 7041/1: gpio-ep93xx: hookup the to_irq callback in the driver
Remove the ep93xx machine specific dependencies for gpio_to_irq() by
hooking up the callback in the driver and using __gpio_to_irq.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Walleij [Mon, 22 Aug 2011 07:40:38 +0000 (08:40 +0100)]
ARM: 7040/1: mach-davinci: break out GPIO driver specifics
The <mach/gpio.h> file is included from upper directories
and deal with generic GPIO and gpiolib stuff. Break out the
platform and driver specific defines and functions into its own
header file.
Cc: Sekhar Nori <nsekhar@ti.com> Cc: Kevin Hilman <khilman@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As per example from the other ARM boards, push the DaVinci TNET
GPIO driver down to the GPIO subsystem so it can be consolidated.
Cc: Sekhar Nori <nsekhar@ti.com> Cc: Kevin Hilman <khilman@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Walleij [Mon, 22 Aug 2011 07:39:28 +0000 (08:39 +0100)]
ARM: 7038/1: mach-davinci: move GPIO driver to GPIO subsystem
As per example from the other ARM boards, push the DaVinci GPIO
driver down to the GPIO subsystem so it can be consolidated.
Cc: Sekhar Nori <nsekhar@ti.com> Cc: Kevin Hilman <khilman@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Walleij [Mon, 22 Aug 2011 07:38:06 +0000 (08:38 +0100)]
ARM: 7037/1: mach-ks8695: fix GPIO LEDs
Enabling the LEDs on the ks8695 doesn't even compile, fix it with
a proper include and also replace a <mach/gpio.h> with the proper
<linux/gpio.h>.
Cc: zeal <zealcook@gmail.com> Cc: Ben Dooks <ben-linux@fluff.org> Acked-by: Daniel Silverstone <dsilvers@simtec.co.uk> Acked-by: Simtec Linux Team <linux@simtec.co.uk> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Walleij [Mon, 22 Aug 2011 07:37:38 +0000 (08:37 +0100)]
ARM: 7036/1: mach-ks8695: break out GPIO driver specifics
The <mach/gpio.h> file is included from upper directories
and deal with generic GPIO and gpiolib stuff. Break out the
platform and driver specific defines and functions into its own
header file.
Cc: zeal <zealcook@gmail.com> Cc: Ben Dooks <ben-linux@fluff.org> Acked-by: Daniel Silverstone <dsilvers@simtec.co.uk> Acked-by: Simtec Linux Team <linux@simtec.co.uk> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Walleij [Mon, 22 Aug 2011 07:37:10 +0000 (08:37 +0100)]
ARM: 7035/1: mach-ks8695: move GPIO driver to GPIO subsystem
As per example from the other ARM boards, push the KS8695 GPIO
driver down to the GPIO subsystem so it can be consolidated.
Cc: zeal <zealcook@gmail.com> Cc: Ben Dooks <ben-linux@fluff.org> Acked-by: Daniel Silverstone <dsilvers@simtec.co.uk> Acked-by: Simtec Linux Team <linux@simtec.co.uk> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Walleij [Mon, 22 Aug 2011 07:34:26 +0000 (08:34 +0100)]
ARM: 7033/1: mach-u300: break out GPIO driver specifics
The <mach/gpio.h> file is included from upper directories
and deal with generic GPIO and gpiolib stuff. Break out the
platform and driver specific defines and functions into its own
header file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Walleij [Mon, 22 Aug 2011 07:33:30 +0000 (08:33 +0100)]
ARM: 7032/1: plat-nomadik: break out GPIO driver specifics
The <[plat|mach]/gpio.h> file is included from upper directories
and deal with generic GPIO and gpiolib stuff. Break out the
platform and driver specific defines and functions into its own
header file.
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Cc: Alessandro Rubini <rubini@unipv.it> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dave Martin [Fri, 19 Aug 2011 17:00:08 +0000 (18:00 +0100)]
ARM: 7031/1: entry: Fix Thumb-2 undef handling for multi-CPU kernels
When v6 and >=v7 boards are supported in the same kernel, the
__und_usr code currently makes a build-time assumption that Thumb-2
instructions occurring in userspace don't need to be supported.
Strictly speaking this is incorrect.
This patch fixes the above case by doing a run-time check on the
CPU architecture in these cases. This only affects kernels which
support v6 and >=v7 CPUs together: plain v6 and plain v7 kernels
are unaffected.
Signed-off-by: Dave Martin <dave.martin@linaro.org> Reviewed-by: Jon Medhurst <tixy@yxit.co.uk> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dave Martin [Fri, 19 Aug 2011 16:59:27 +0000 (17:59 +0100)]
ARM: 7030/1: entry: Remove unnecessary masking when decoding Thumb-2 instructions
When testing whether a Thumb-2 instruction is 32 bits long or not,
the masking done in order to test bits 11-15 of the first
instruction halfword won't affect the result of the comparison, so
remove it.
Signed-off-by: Dave Martin <dave.martin@linaro.org> Reviewed-by: Jon Medhurst <tixy@yxit.co.uk> Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dave Martin [Fri, 19 Aug 2011 16:58:35 +0000 (17:58 +0100)]
ARM: 7029/1: Make cpu_architecture into a global variable
The CPU architecture really should not be changing at runtime, so
make it a global variable instead of a function.
The cpu_architecture() function declared in <asm/system.h> remains
the correct way to read this variable from C code.
Signed-off-by: Dave Martin <dave.martin@linaro.org> Reviewed-by: Jon Medhurst <tixy@yxit.co.uk> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Josef Bacik [Sat, 20 Aug 2011 12:29:51 +0000 (08:29 -0400)]
Btrfs: fix 64 bit divide problem
This fixes a regression introduced by commit cdcb725c05fe ("Btrfs: check
if there is enough space for balancing smarter"). We can't do 64-bit
divides on 32-bit architectures.
In cases where we need to divide/multiply by 2 we should just left/right
shift respectively, and in cases where theres N number of devices use
do_div. Also make the counters u64 to match up with rw_devices.
Thanks,
Linus Torvalds [Sun, 21 Aug 2011 13:59:41 +0000 (06:59 -0700)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: flush any pending end_io requests before DIO reads w/dioread_nolock
ext4: fix nomblk_io_submit option so it correctly converts uninit blocks
ext4: Resolve the hang of direct i/o read in handling EXT4_IO_END_UNWRITTEN.
ext4: call ext4_ioend_wait and ext4_flush_completed_IO in ext4_evict_inode
ext4: Fix ext4_should_writeback_data() for no-journal mode
Linus Torvalds [Sun, 21 Aug 2011 13:59:02 +0000 (06:59 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: sound/aoa/fabrics/layout.c: remove unneeded kfree
ALSA: hda - Fix error check from snd_hda_get_conn_index() in patch_cirrus.c
ALSA: hda - Don't spew too many ELD errors
ALSA: usb-audio - Fix missing mixer dB information
ALSA: hda - Add "PCM" volume to vmaster slave list
ALSA: hda - Fix duplicated capture-volume creation for ALC268 models
ALSA: ac97: Add HP Compaq dc5100 SFF(PT003AW) to Headphone Jack Sense whitelist
ALSA: snd_usb_caiaq: track submitted output urbs
Randy Dunlap [Sat, 20 Aug 2011 18:49:43 +0000 (11:49 -0700)]
pci: fix new kernel-doc warning in pci.c
Fix new kernel-doc warning in pci.c:
Warning(drivers/pci/pci.c:3259): No description found for parameter 'mps'
Warning(drivers/pci/pci.c:3259): Excess function parameter 'rq' description in 'pcie_set_mps'
David S. Miller [Sun, 21 Aug 2011 00:14:54 +0000 (17:14 -0700)]
sparc: Allow handling signals when stack is corrupted.
If we can't push the pending register windows onto the user's stack,
we disallow signal delivery even if the signal would be delivered on a
valid seperate signal stack.
Add a register window save area in the signal frame, and store any
unsavable windows there.
On sigreturn, if any windows are still queued up in the signal frame,
try to push them back onto the stack and if that fails we kill the
process immediately.
This allows the debug/tst-longjmp_chk2 glibc test case to pass.
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiejing Zhang [Sat, 20 Aug 2011 21:38:01 +0000 (14:38 -0700)]
Input: max11801_ts - correct license statement
The original license statement was confusing since it was unclear if
the license was pure GPLv2 or GPLv2+ and did not match the license
of the driver max11801_ts was derived from. The license is GPLv2+.
It happens that if a packet arrives in a VC between the call to open it on
the hardware and the call to change the backend to br2684, br2684_regvcc
processes the packet and oopses dereferencing skb->dev because it is
NULL before the call to br2684_push().
(
if (...) { ... when != kfree(x)
when != x = E3
when != E3 = x
* return ...;
}
... when != x = E2
when != I(...,x,...) S
if (...) { ... when != x = E4
kfree(x); ... return ...; }
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Sat, 20 Aug 2011 07:14:45 +0000 (09:14 +0200)]
ALSA: hda - Don't spew too many ELD errors
Currently HD-audio driver shows the all error ELD byte as an error
in the kernel message. This is annoying when the video driver doesn't
set the correct ELD from the beginning. e.g. radeon sends a zero-byte
data, but we still check ELD with the fixed 128 byte as a workaround
for some broken devices, it spews 128-times errors.
For avoiding this, the driver aborts reading when the first byte is
invalid. In such a case, the whole data is certainly invalid.
Linus Torvalds [Sat, 20 Aug 2011 06:07:08 +0000 (23:07 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/drm-intel
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/drm-intel:
drm/i915: set GFX_MODE to pre-Ivybridge default value even on Ivybridge
Mike Frysinger [Sat, 20 Aug 2011 03:51:52 +0000 (23:51 -0400)]
Blackfin: merge asm/mutex.h into kbuild too
This header was being rewritten while the asm-generic kbuild support
was in flight, so it missed out on the update. Punt the stub and use
the kbuild now that everything has settled.
Jiaying Zhang [Fri, 19 Aug 2011 23:13:32 +0000 (19:13 -0400)]
ext4: flush any pending end_io requests before DIO reads w/dioread_nolock
There is a race between ext4 buffer write and direct_IO read with
dioread_nolock mount option enabled. The problem is that we clear
PageWriteback flag during end_io time but will do
uninitialized-to-initialized extent conversion later with dioread_nolock.
If an O_direct read request comes in during this period, ext4 will return
zero instead of the recently written data.
This patch checks whether there are any pending uninitialized-to-initialized
extent conversion requests before doing O_direct read to close the race.
Note that this is just a bandaid fix. The fundamental issue is that we
clear PageWriteback flag before we really complete an IO, which is
problem-prone. To fix the fundamental issue, we may need to implement an
extent tree cache that we can use to look up pending to-be-converted extents.
Jesse Barnes [Fri, 12 Aug 2011 22:28:32 +0000 (15:28 -0700)]
drm/i915: set GFX_MODE to pre-Ivybridge default value even on Ivybridge
Prior to Ivybridge, the GFX_MODE would default to 0x800, meaning that
MI_FLUSH would flush the TLBs in addition to the rest of the caches
indicated in the MI_FLUSH command. However starting with Ivybridge, the
register defaults to 0x2800 out of reset, meaning that to invalidate the
TLB we need to use PIPE_CONTROL. Since we're not doing that yet, go
back to the old default so things work.
v2: don't forget to actually *clear* the new bit
Reviewed-by: Eric Anholt <eric@anholt.net> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Tested-by: Kenneth Graunke <kenneth@whitecape.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Linus Torvalds [Fri, 19 Aug 2011 17:47:07 +0000 (10:47 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
* 'for-linus' of git://git.kernel.dk/linux-block: (23 commits)
Revert "cfq: Remove special treatment for metadata rqs."
block: fix flush machinery for stacking drivers with differring flush flags
block: improve rq_affinity placement
blktrace: add FLUSH/FUA support
Move some REQ flags to the common bio/request area
allow blk_flush_policy to return REQ_FSEQ_DATA independent of *FLUSH
xen/blkback: Make description more obvious.
cfq-iosched: Add documentation about idling
block: Make rq_affinity = 1 work as expected
block: swim3: fix unterminated of_device_id table
block/genhd.c: remove useless cast in diskstats_show()
drivers/cdrom/cdrom.c: relax check on dvd manufacturer value
drivers/block/drbd/drbd_nl.c: use bitmap_parse instead of __bitmap_parse
bsg-lib: add module.h include
cfq-iosched: Reduce linked group count upon group destruction
blk-throttle: correctly determine sync bio
loop: fix deadlock when sysfs and LOOP_CLR_FD race against each other
loop: add BLK_DEV_LOOP_MIN_COUNT=%i to allow distros 0 pre-allocated loop devices
loop: add management interface for on-demand device allocation
loop: replace linked list of allocated devices with an idr index
...
Linus Torvalds [Fri, 19 Aug 2011 17:02:37 +0000 (10:02 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: OF: Don't crash when bridge parent is NULL.
PCI: export pcie_bus_configure_settings symbol
PCI: code and comments cleanup
PCI: make cardbus-bridge resources optional
PCI: make SRIOV resources optional
PCI : ability to relocate assigned pci-resources
PCI: honor child buses add_size in hot plug configuration
PCI: Set PCI-E Max Payload Size on fabric
projects / karo-tx-linux.git / log