Grant Erickson [Tue, 8 Jul 2008 15:03:06 +0000 (01:03 +1000)]
ibm_newemac: Add MII mode support to the EMAC RGMII bridge.
This patch adds support to the RGMII handler in the EMAC driver for
the MII PHY mode such that device tree entries of the form `phy-mode = "mii";'
are recognized and handled appropriately.
While logically, in software, "gmii" and "mii" modes are the same,
they are wired differently, so it makes sense to allow DTS authors to
specify each explicitly.
Signed-off-by: Grant Erickson <gerickson@nuovations.com> Acked-by: Stefan Roese <sr@denx.de> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Jeff Garzik <jgarzik@pobox.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc: Don't spin on sync instruction at boot time
Push the sync below the secondary smp init hold loop and comment its purpose.
This should speed up boot by reducing global traffic during the single-threaded
portion of boot.
Signed-off-by: Sonny Rao <sonnyrao@us.ibm.com> Signed-off-by: Milton Miller <miltonm@bga.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Dave Kleikamp [Wed, 9 Jul 2008 15:28:07 +0000 (01:28 +1000)]
powerpc: Remove unnecessary condition when sanity-checking WIMG bits
It is okay for both _PAGE_GUARDED and _PAGE_COHERENT (G and M) to be set
in the same pte. In fact, even if that were not the case, there doesn't
seem to be any place where G is set without also setting I (_PAGE_NO_CACHE),
so the test for I is sufficient as a condition to clear _PAGE_COHERENT
when filling the hash table.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Background from Maynard Johnson:
As of POWER6, a set of 32 common events is defined that must be
supported on all future POWER processors. The main impetus for this
compat set is the need to support partition migration, especially from
processor P(n) to processor P(n+1), where performance software that's
running in the new partition may not be knowledgeable about processor
P(n+1). If a performance tool determines it does not support the
physical processor, but is told (via the
PPC_FEATURE_PSERIES_PERFMON_COMPAT bit) that the processor supports
the notion of the PMU compat set, then the performance tool can
surface just those events to the user of the tool.
PPC_FEATURE_PSERIES_PERFMON_COMPAT indicates that the PMU supports at
least this basic subset of events which is compatible across POWER
processor lines.
Signed-off-by: Nathan Lynch <ntl@pobox.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc: Add driver for Barrier Synchronization Register
Adds a character driver for BSR support on IBM POWER systems including
Power5 and Power6. The BSR is an optional processor facility not currently
implemented by any other processors. It's primary purpose is fast large SMP
synchronization. More details on the BSR are in comments to the code which
follows. This patch adds BSR driver to pseries_defconfig.
Signed-off-by: Sonny Rao <sonnyrao@linux.vnet.ibm.com> Signed-off-by: Joel Schopp <jschopp@austin.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Stephen Rothwell [Mon, 14 Jul 2008 09:25:57 +0000 (19:25 +1000)]
powerpc: mman.h export fixups
Commit ef3d3246a0d06be622867d21af25f997aeeb105f ("powerpc/mm: Add Strong
Access Ordering support") in the powerpc/{next,master} tree caused the
following in a powerpc allmodconfig build:
usr/include/asm/mman.h requires linux/mm.h, which does not exist in exported headers
We should not use CONFIG_PPC64 in an unprotected (by __KERNEL__)
section of an exported include file and linux/mm.h is not exported. So
protect the whole section that is CONFIG_PPC64 with __KERNEL__ and put
the two introduced includes in there as well.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Kim Phillips [Wed, 9 Jul 2008 00:13:33 +0000 (19:13 -0500)]
powerpc/fsl: update crypto node definition and device tree instances
delete obsolete device-type property, delete model property
(use compatible property instead), prepend "fsl," to Freescale
specific properties. Add nodes to device trees that are missing them,
and fix broken property values in other trees.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Fri, 27 Jun 2008 16:26:26 +0000 (11:26 -0500)]
powerpc: Add 82xx/83xx/86xx to 6xx Multiplatform
There isn't any reason at this point that we can't build 82xx, 83xx & 86xx
support in with the other 6xx based boards. Twiddle the Kconfigs to allow
this.
This allows us to remove the machine type selection for related to 6xx.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Fri, 27 Jun 2008 13:03:13 +0000 (08:03 -0500)]
powerpc/booke: don't reinitialize time base
For some reason long ago I decided that we should zero out the time base
when we calibrate the decrementer. The problem is that this can be
harmful in SMP systems where the firmware has already synchronized the
time bases on the various cores.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Initialize I2C pins on boards with CPM1/CPM2 controllers and document the
i2c bus in booting-without-of.
The boards don't have any I2C chips connected to the I2C bus, so unless
some external chips are connected to the boards, this code is just an
example of setting everything else up.
Signed-off-by: Jochen Friedrich <jochen@scram.de> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Set port->fifosize to the software FIFO size, and update the port timeout
when the baud rate is modified. SCC ports have an optional 32 byte hardware
FIFO which is currently not taken into account, as there is no documented way
to check when the FIFO becomes empty.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Nye Liu [Fri, 27 Jun 2008 20:01:00 +0000 (13:01 -0700)]
powerpc/CPM: Minor cosmetic changes to udbg_putc
udbg_putc is a *function pointer* that is initialized during
udbg_init_cpm. It might not be initialized properly when called from
udbg_putc_cpm(), so (recursively) call udbg_putc_cpm() directly.
Signed-off-by: Nye Liu <nyet@mrv.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Anton Vorontsov [Tue, 1 Jul 2008 13:04:38 +0000 (17:04 +0400)]
powerpc/86xx: mpc8610_hpcd: fix interrupt trigger type for ULi IDE
i8259 PIC is disabled on MPC8610HPCD, and ULi IDE is configured to use
PCI sideband interrupt that is specified in the device tree.
Current HPCD's device tree specify that IDE interrupt is low to high
sensitive, but in practice ULi IDE throws active-high interrupts (not
active-low as all normal PCI devices).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rune Torgersen [Tue, 20 May 2008 19:39:17 +0000 (14:39 -0500)]
cpm_uart: Fix cpm uart corruption with PREEMPT_RT
Fix CPM serial port corruption when running with CONFIG_PREEMPT_RT.
Userland usage of console, and kernel printf's were stepping on each others toes.
Also only take lock if not in an oops.
Signed-off-by: Rune Torgersen <runet@innovsys.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Commit f18f982ab ("sched: CPU hotplug events must not destroy scheduler
domains created by the cpusets") introduced a hotplug-related problem as
described below:
/*
* Force a reinitialization of the sched domains hierarchy. The domains
* and groups cannot be updated in place without racing with the balancing
* code, so we temporarily attach all running cpus to the NULL domain
* which will prevent rebalancing while the sched domains are recalculated.
*/
The sched-domains should be rebuilt when a CPU_DOWN ops. has been
completed, effectively either upon CPU_DEAD{_FROZEN} (upon success) or
CPU_DOWN_FAILED{_FROZEN} (upon failure -- restore the things to their
initial state). That's what update_sched_domains() also does but only
for !CPUSETS case.
With f18f982ab, sched-domains' reinitialization is delegated to
CPUSETS code:
Being called for CPU_UP_PREPARE and if its callback is called after
update_sched_domains()), it just negates all the work done by
update_sched_domains() -- i.e. a soon-to-be-offline cpu is included in
the sched-domains and that makes it visible for the load-balancer
while the CPU_DOWN ops. is in progress.
__migrate_live_tasks() moves the tasks off a 'dead' cpu (it's already
"offline" when this function is called).
try_to_wake_up() is called for one of these tasks from another CPU ->
the load-balancer (wake_idle()) picks up a "dead" CPU and places the
task on it. Then e.g. BUG_ON(rq->nr_running) detects this a bit later
-> oops.
Signed-off-by: Dmitry Adamushko <dmitry.adamushko@gmail.com> Tested-by: Vegard Nossum <vegard.nossum@gmail.com> Cc: Paul Menage <menage@google.com> Cc: Max Krasnyansky <maxk@qualcomm.com> Cc: Paul Jackson <pj@sgi.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: miaox@cn.fujitsu.com Cc: rostedt@goodmis.org Cc: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] bsg: fix oops on remove
[SCSI] fusion: default MSI to disabled for SPI and FC controllers
[SCSI] ipr: Fix HDIO_GET_IDENTITY oops for SATA devices
[SCSI] mptspi: fix oops in mptspi_dv_renegotiate_work()
[SCSI] erase invalid data returned by device
Jeff Layton [Sat, 12 Jul 2008 20:48:00 +0000 (13:48 -0700)]
cifs: fix wksidarr declaration to be big-endian friendly
The current definition of wksidarr works fine on little endian arches
(since cpu_to_le32 is a no-op there), but on big-endian arches, it fails
to compile with this error:
error: braced-group within expression allowed only inside a function
The problem is that this static declaration has cpu_to_le32 embedded
within it, and that expands into a function macro. We need to use
__constant_cpu_to_le32() instead.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Cc: Steven French <sfrench@us.ibm.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeff Layton [Sat, 12 Jul 2008 20:47:59 +0000 (13:47 -0700)]
cifs: fix inode leak in cifs_get_inode_info_unix
Try this:
mount a share with unix extensions
create a file on it
umount the share
You'll get the following message in the ring buffer:
VFS: Busy inodes after unmount of cifs. Self-destruct in 5 seconds. Have a
nice day...
...the problem is that cifs_get_inode_info_unix is creating and hashing
a new inode even when it's going to return error anyway. The first
lookup when creating a file returns an error so we end up leaking this
inode before we do the actual create. This appears to be a regression
caused by commit 0e4bbde94fdc33f5b3d793166b21bf768ca3e098.
The following patch seems to fix it for me, and fixes a minor
formatting nit as well.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Acked-by: Steven French <sfrench@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Robert Richter [Sat, 12 Jul 2008 20:47:57 +0000 (13:47 -0700)]
OProfile kernel maintainership changes
Cc: Philippe Elie <phil.el@wanadoo.fr> Cc: John Levon <levon@movementarian.org> Cc: Maynard Johnson <maynardj@us.ibm.com> Cc: Richard Purdie <rpurdie@openedhand.com> Cc: Daniel Hansel <daniel.hansel@linux.vnet.ibm.com> Cc: Jason Yeh <jason.yeh@amd.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Robert Richter <robert.richter@amd.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andres Salomon [Sat, 12 Jul 2008 20:47:54 +0000 (13:47 -0700)]
ov7670: clean up ov7670_read semantics
Cortland Setlow pointed out a bug in ov7670.c where the result from
ov7670_read() was just being checked for !0, rather than <0. This made me
realize that ov7670_read's semantics were rather confusing; it both fills
in 'value' with the result, and returns it. This is goes against general
kernel convention; so rather than fixing callers, let's fix the function.
This makes ov7670_read return <0 in the case of an error, and 0 upon
success. Thus, code like:
res = ov7670_read(...);
if (!res)
goto error;
..will work properly.
Signed-off-by: Cortland Setlow <csetlow@tower-research.com> Signed-off-by: Andres Salomon <dilinger@debian.org> Acked-by: Jonathan Corbet <corbet@lwn.net> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I had 8250.nr_uarts=16 in the boot line of a test kernel and I had a weird
mysterious crash in sysfs. After taking an in-depth look I realized that
CONFIG_SERIAL_8250_NR_UARTS was set to 4 and I was walking off the end of
the serial8250_ports array.
Ouch!!!
Don't let this happen to someone else.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Acked-by: Alan Cox <alan@redhat.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch is a bugfix for how defio handles multiple processes manipulating
the same framebuffer.
Thanks to Bernard Blackham for identifying this bug.
It occurs when two applications mmap the same framebuffer and concurrently
write to the same page. Normally, this doesn't occur since only a single
process mmaps the framebuffer. The symptom of the bug is that the mapping
applications will hang. The cause is that defio incorrectly tries to add the
same page twice to the pagelist. The solution I have is to walk the pagelist
and check for a duplicate before adding. Since I needed to walk the pagelist,
I now also keep the pagelist in sorted order.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com> Cc: Bernard Blackham <bernard@largestprime.net> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Darren Jenkins [Sat, 12 Jul 2008 20:47:50 +0000 (13:47 -0700)]
drivers/isdn/i4l/isdn_common.c fix small resource leak
Coverity CID: 1356 RESOURCE_LEAK
I found a very old patch for this that was Acked but did not get applied
https://lists.linux-foundation.org/pipermail/kernel-janitors/2006-September/016362.html
There looks to be a small leak in isdn_writebuf_stub() in isdn_common.c, when
copy_from_user() returns an un-copied data length (length != 0). The below
patch should be a minimally invasive fix.
Signed-off-by: Darren Jenkins <darrenrjenkins@gmailcom> Acked-by: Karsten Keil <kkeil@suse.de> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Grant Likely [Sat, 12 Jul 2008 18:11:43 +0000 (12:11 -0600)]
powerpc: Modify MPC52xx maintainers entry to cover all MPC5xxx parts
Linux now supports the MPC5121 part and is handled by the same
maintainer. Update MAINTAINERS to reflect this. Also remove URLs
which are out of date or are not particularly relevant.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
John Rigby [Wed, 9 Jul 2008 20:54:04 +0000 (14:54 -0600)]
powerpc/mpc5121: Add support for CPLD on MPC5121ADS board
Add a interrupt host for the interrupt controller in the mpc5121ads cpld.
PCI interrupts are 0-7 the rest are 8-15 Touchscreen pendown irq is
hardwired to irq1 All other irqs are chained to irq0
Signed-off-by: John Rigby <jrigby@freescale.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
John Rigby [Wed, 9 Jul 2008 20:54:03 +0000 (14:54 -0600)]
powerpc/mpc5121: Add generic board support for MPC5121 platforms
Move shared code from mpc5121_ads.c to new file mpc512x_shared.c
- mpc512x_find_ips_freq -> unchanged
- contents of mpc5121_ads_init_IRQ -> mpc512x_init_IRQ
- looking for fsl,mpc5121-ipic instead of fsl,ipic
- mpc5121_ads_declare_of_platform_devices -> mpc5121_declare_of_platform_devices
- and use compatible for lookup instead of node name
Add new generic board setup mpc5121_generic.c
Signed-off-by: John Rigby <jrigby@freescale.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
John Rigby [Wed, 9 Jul 2008 20:54:02 +0000 (14:54 -0600)]
powerpc/mpc5121: Add clock driver
Plugs into the generic powerpc clock driver in
arch/powerpc/kernel/clock.c
The following subset of clk_interface is implemented:
clk_get, clk_put: get clock via name, release clock
clk_enable, clk_disable: enable or disable clock
clk_get_rate: get clock rate in Hz
clk_set_rate: stubbed
clk_round_rate: stubbed
clk_set_parent: NULL
clk_get_parent: NULL
Signed-off-by: John Rigby <jrigby@freescale.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
John Rigby [Wed, 9 Jul 2008 20:54:01 +0000 (14:54 -0600)]
powerpc/mpc5121: Update device tree for MPC5121ADS evaluation board
Current device tree is only bare bones. This patch adds nodes to make
it a complete tree for the MPC5121ads.
Added nodes include:
mbx - opengl coprocessor
nfc - nand flash controller
cpld-pic - on board cpld
rtc
clock - clock control
pmc - power management control
gpio
mscan - can module
i2c
axe - audio coprocessor
display - display interface unit
mdio
ethernet
usb
ioctl - pin config
pata
ac97 - PSC configured as AC97
pscfifo - psc fifo configuration
dma
pci
Fix typo in header changing MDS to ADS.
Add a compatible property of the form "fsl,mpc5121-..."
to nodes missing one.
Changed localbus compatible to fsl,mpc5121-localbus, this does
not break anything because the only code that uses it finds it
via the node name, not compatible.
Signed-off-by: John Rigby <jrigby@freescale.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Grant Likely [Fri, 11 Jul 2008 22:17:58 +0000 (16:17 -0600)]
powerpc/mpc5200: fix compile warnings in bestcomm driver
Fix for the following compiler warnings:
CC arch/powerpc/sysdev/bestcomm/bestcomm.o
arch/powerpc/sysdev/bestcomm/bestcomm.c: In function 'mpc52xx_bcom_probe':
arch/powerpc/sysdev/bestcomm/bestcomm.c:446:
warning: format '%08lx' expects type 'long unsigned int',
but argument 2 has type 'phys_addr_t'
CC arch/powerpc/sysdev/bestcomm/sram.o
arch/powerpc/sysdev/bestcomm/sram.c: In function 'bcom_sram_init':
arch/powerpc/sysdev/bestcomm/sram.c:89:
warning: format '%08lx' expects type 'long unsigned int',
but argument 3 has type 'phys_addr_t'
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Grant Likely [Wed, 2 Jul 2008 03:38:16 +0000 (21:38 -0600)]
powerpc/mpc5200: Add PSC helpers for bestcomm engine
Simplify the interface for setting up bestcomm DMA to PSCs by adding
some helper functions. The helper function sets the correct values
for the initator and ipr values in PSC DMA tasks based on the PSC
number.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
OpenFirmware: Include <linux/of_i2c.h> from of_i2c.c.
drivers/of/of_i2c.c should include <linux/of_i2c.h> for the prototype
for of_register_i2c_devices().
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca> Acked-by: Jean Delvare <khali@linux-fr.org> Acked-by: Jochen Friedrich <jochen@scram.de> Acked-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Andre Schwarz [Thu, 10 Jul 2008 09:53:16 +0000 (11:53 +0200)]
powerpc/mpc5200: PCI write combine timer
On MPC5200 the PCI target control register (PCITCR) @ MBAR + 0xD6C is
initialized with only bit 7 (Latrule disable) set. The 8-Bit write
combine timer (Bits 24..31) should be also set to a reasonable value
_greater zero_ (0x08 = default) since setting it to 0x00 leads to
_very poor_ performance as a PCI target since external burst won't be
possible at all.
Setting the WCT to 0x08 (cache-line size) leads to good overall perfomance.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
James Bottomley [Mon, 7 Jul 2008 20:50:01 +0000 (15:50 -0500)]
[SCSI] bsg: fix oops on remove
If you do a modremove of any sas driver, you run into an oops on
shutdown when the host is removed (coming from the host bsg device).
The root cause seems to be that there's a use after free of the
bsg_class_device: In bsg_kref_release_function, this is used (to do a
put_device(bcg->parent) after bcg->release has been called. In sas (and
possibly many other things) bcd->release frees the queue which contains
the bsg_class_device, so we get a put_device on unreferenced memory.
Fix this by taking a copy of the pointer to the parent before releasing
bsg.
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
James Bottomley [Fri, 11 Jul 2008 03:10:55 +0000 (22:10 -0500)]
[SCSI] fusion: default MSI to disabled for SPI and FC controllers
There's a fault on the FC controllers that makes them not respond
correctly to MSI. The SPI controllers are fine, but are likely to be
onboard on older motherboards which don't handle MSI correctly, so
default both these cases to disabled. Enable by setting the module
parameter mpt_msi_enable=1.
For the SAS case, enable MSI by default, but it can be disabled by
setting the module parameter mpt_msi_enable=0.
Cc: "Prakash, Sathya" <sathya.prakash@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mark Rustad [Thu, 10 Jul 2008 19:27:11 +0000 (14:27 -0500)]
[PATCH] IPMI: return correct value from ipmi_write
This patch corrects the handling of write operations to the IPMI watchdog
to work as intended by returning the number of characters actually
processed. Without this patch, an "echo V >/dev/watchdog" enables the
watchdog if IPMI is providing the watchdog function.
Signed-off-by: Mark Rustad <MRustad@gmail.com> Signed-off-by: Corey Minyard <cminyard@mvista.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Brian King [Fri, 11 Jul 2008 18:37:50 +0000 (13:37 -0500)]
[SCSI] ipr: Fix HDIO_GET_IDENTITY oops for SATA devices
Currently, ipr does not support HDIO_GET_IDENTITY to SATA devices.
An oops occurs if userspace attempts to send the command. Since hald
issues the command, ensure we fail the ioctl in ipr. This is a
temporary solution to the oops. Once the ipr libata EH conversion
is upstream, ipr will fully support HDIO_GET_IDENTITY.
Tested-by: Milton Miller <miltonm@bga.com> Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata-acpi: don't call sleeping function from invalid context
Added Targa Visionary 1000 IDE adapter to pata_sis.c
libata-acpi: filter out DIPM enable
Dave Chinner [Fri, 11 Jul 2008 07:43:55 +0000 (17:43 +1000)]
Fix reference counting race on log buffers
When we release the iclog, we do an atomic_dec_and_lock to determine if
we are the last reference and need to trigger update of log headers and
writeout. However, in xlog_state_get_iclog_space() we also need to
check if we have the last reference count there. If we do, we release
the log buffer, otherwise we decrement the reference count.
But the compare and decrement in xlog_state_get_iclog_space() is not
atomic, so both places can see a reference count of 2 and neither will
release the iclog. That leads to a filesystem hang.
Close the race by replacing the atomic_read() and atomic_dec() pair with
atomic_add_unless() to ensure that they are executed atomically.
Signed-off-by: Dave Chinner <david@fromorbit.com> Reviewed-by: Tim Shimmin <tes@sgi.com> Tested-by: Eric Sandeen <sandeen@sandeen.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some BIOSen enable DIPM via _GTF which causes command timeouts under
certain configuration. This didn't occur on 2.6.25 because 2.6.25
defaulted to SRST, so _GTF wasn't executed during boot probe, so ahci
host reset disabled DIPM and as _GTF wasn't executed after SRST, DIPM
wasn't enabled. On 2.6.26, hardreset is used during probe and after
probe _GTF is executed enabling DIPM and thus the failures.
This patch could theoretically disable DIPM on machines which used to
have it enabled on 2.6.25 but AFAIK ahci is currently the only driver
which uses SATA ACPI hierarchy (_SDD) and as the host reset would have
always disabled DIPM, this shouldn't happen.
Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Paul Gortmaker [Fri, 11 Jul 2008 00:30:48 +0000 (17:30 -0700)]
rtc: fix reported IRQ rate for when HPET is enabled
The IRQ rate reported back by the RTC is incorrect when HPET is enabled.
Newer hardware that has HPET to emulate the legacy RTC device gets this value
wrong since after it sets the rate, it returns before setting the variable
used to report the IRQ rate back to users of the device -- so the set rate and
the reported rate get out of sync.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: David Brownell <david-b@pacbell.net> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (27 commits)
tun: Persistent devices can get stuck in xoff state
xfrm: Add a XFRM_STATE_AF_UNSPEC flag to xfrm_usersa_info
ipv6: missed namespace context in ipv6_rthdr_rcv
netlabel: netlink_unicast calls kfree_skb on error path by itself
ipv4: fib_trie: Fix lookup error return
tcp: correct kcalloc usage
ip: sysctl documentation cleanup
Documentation: clarify tcp_{r,w}mem sysctl docs
netfilter: nf_nat_snmp_basic: fix a range check in NAT for SNMP
netfilter: nf_conntrack_tcp: fix endless loop
libertas: fix memory alignment problems on the blackfin
zd1211rw: stop beacons on remove_interface
rt2x00: Disable synchronization during initialization
rc80211_pid: Fix fast_start parameter handling
sctp: Add documentation for sctp sysctl variable
ipv6: fix race between ipv6_del_addr and DAD timer
irda: Fix netlink error path return value
irda: New device ID for nsc-ircc
irda: via-ircc proper dma freeing
sctp: Mark the tsn as received after all allocations finish
...
Max Krasnyansky [Thu, 10 Jul 2008 23:59:11 +0000 (16:59 -0700)]
tun: Persistent devices can get stuck in xoff state
The scenario goes like this. App stops reading from tun/tap.
TX queue gets full and driver does netif_stop_queue().
App closes fd and TX queue gets flushed as part of the cleanup.
Next time the app opens tun/tap and starts reading from it but
the xoff state is not cleared. We're stuck.
Normally xoff state is cleared when netdev is brought up. But
in the case of persistent devices this happens only during
initial setup.
The fix is trivial. If device is already up when an app opens
it we clear xoff state and that gets things moving again.
Signed-off-by: Max Krasnyansky <maxk@qualcomm.com> Tested-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
xfrm: Add a XFRM_STATE_AF_UNSPEC flag to xfrm_usersa_info
Add a XFRM_STATE_AF_UNSPEC flag to handle the AF_UNSPEC behavior for
the selector family. Userspace applications can set this flag to leave
the selector family of the xfrm_state unspecified. This can be used
to to handle inter family tunnels if the selector is not set from
userspace.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Thu, 10 Jul 2008 23:52:52 +0000 (16:52 -0700)]
ipv4: fib_trie: Fix lookup error return
In commit a07f5f508a4d9728c8e57d7f66294bf5b254ff7f "[IPV4] fib_trie: style
cleanup", the changes to check_leaf() and fn_trie_lookup() were wrong - where
fn_trie_lookup() would previously return a negative error value from
check_leaf(), it now returns 0.
Now fn_trie_lookup() doesn't appear to care about plen, so we can revert
check_leaf() to returning the error value.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Tested-by: William Boughton <bill@boughton.de> Acked-by: Stephen Heminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Take out the confusing language in tcp_frto, and organize the
undocumented values.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Acked-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: David S. Miller <davem@davemloft.net>
"The register %ecx looks innocent but is very important here. The disassembly:
mov %edx,%ecx
shr $0x2,%ecx
rep stos %eax,%es:(%edi) <-- the fault
So %ecx has been loaded from %edx... which is 0x6b6b6b6b/POISON_FREE.
(0x6b6b6b6b >> 2 == 0x1adadada.)
%ecx is the counter for the memset, from here:
memset(object, 0, c->objsize);
i.e. %ecx was loaded from c->objsize, so "c" must have been freed.
Where did "c" come from? Uh-oh...
c = get_cpu_slab(s, smp_processor_id());
This looks like it has very much to do with CPU hotplug/unplug. Is
there a race between SLUB/hotplug since the CPU slab is used after it
has been freed?"
Good analysis.
Yeah, it's possible that a caller of kmem_cache_alloc() -> slab_alloc()
can be migrated on another CPU right after local_irq_restore() and
before memset(). The inital cpu can become offline in the mean time (or
a migration is a consequence of the CPU going offline) so its
'kmem_cache_cpu' structure gets freed ( slab_cpuup_callback).
At some point of time the caller continues on another CPU having an
obsolete pointer...
Kernel Bugzilla #11063 points out that on some architectures (e.g. x86_32)
exec'ing an ELF without a PT_GNU_STACK program header should default to an
executable stack; but this got broken by the unlimited argv feature because
stack vma is now created before the right personality has been established:
so breaking old binaries using nested function trampolines.
Therefore re-evaluate VM_STACK_FLAGS in setup_arg_pages, where stack
vm_flags used to be set, before the mprotect_fixup. Checking through
our existing VM_flags, none would have changed since insert_vm_struct:
so this seems safer than finding a way through the personality labyrinth.
Nick Piggin [Thu, 10 Jul 2008 07:25:35 +0000 (17:25 +1000)]
Fix PREEMPT_RCU without HOTPLUG_CPU
PREEMPT_RCU without HOTPLUG_CPU is broken. The rcu_online_cpu is called
to initially populate rcu_cpu_online_map with all online CPUs when the
hotplug event handler is installed, and also to populate the map with
CPUs as they come online. The former case is meant to happen with and
without HOTPLUG_CPU, but without HOTPLUG_CPU, the rcu_offline_cpu
function is no-oped -- while it still gets called, it does not set the
rcu CPU map.
With a blank RCU CPU map, grace periods get to tick by completely
oblivious to active RCU read side critical sections. This results in
free-before-grace bugs.
Fix is obvious once the problem is known. (Also, change __devinit to
__cpuinit so the function gets thrown away on !HOTPLUG_CPU kernels).
Signed-off-by: Nick Piggin <npiggin@suse.de> Reported-and-tested-by: Alexey Dobriyan <adobriyan@gmail.com> Acked-by: Ingo Molnar <mingo@elte.hu> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
[ Nick is my personal hero of the day - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark Fasheh [Thu, 10 Jul 2008 16:25:39 +0000 (09:25 -0700)]
ocfs2: Fix flags in ocfs2_file_lock
The stack-glue merge changed the way we use flags in dlmglue in that we now
use the fs/dlm equivalents. Unfortunately, a merge error left the new flock
code only partially updated. This took a while to show up though, because
the lock level constants are actually identical between o2dlm and fs/dlm.
The *_CONVERT and *_NOQUEUE flags have different values though, which is
eventually causing a crash in flags_to_o2dlm().
projects / linux-beck.git / log