drm/i915: Introduce i915_gem_object_create_stolen()

Allow for the creation of GEM objects backed by stolen memory. As these
are not backed by ordinary pages, we create a fake dma mapping and store
the address in the scatterlist rather than obj->pages.

v2: Mark _i915_gem_object_create_stolen() as static, as noticed by Jesse
Barnes.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Support readback of stolen objects upon error

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Allow objects to be created with no backing pages, but stolen space

In order to accommodate objects that are not backed by struct pages, but
instead point into a contiguous region of stolen space, we need to make
various changes to avoid dereferencing obj->pages or obj->base.filp.

First introduce a marker for the stolen object, that specifies its
offset into the stolen region and implies that it has no backing pages.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Delay allocation of stolen space for FBC

As FBC is commonly disabled due to limitations of the chipset upon
output configurations, on many systems FBC is never enabled. For those
systems, it is advantageous to make use of the stolen memory for other
objects and so we defer allocation of the FBC chunk until we actually
require it. This increases the likelihood of that allocation failing,
but that in turns means that we are already taking advantage of the
stolen memory!

As well as delaying the allocation from driver initialisation until the
first use of FBC, we also return the stolen block after we finish using
it - allowing greater flexibility in our usage of stolen space. A side
effect of this is that we can then attempt to allocate only the required
amount of space (with a little slack to reduce reallocation rate and
avoid fragmentation).

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Avoid clearing preallocated regions from the GTT

As yet we do not do any preallocation (chicken-and-egg problem), but we
may like to preserve anything already allocated by the BIOS or grub and
reuse for own purposes after initialising the driver.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Fix detection of base of stolen memory

The routine to query the base of stolen memory was using the wrong
registers and the wrong encodings on virtually every platform.

It was not until the G33 refresh, that a PCI config register was
introduced that explicitly said where the stolen memory was. Prior to
865G there was not even a register that said where the end of usable
low memory was and where the stolen memory began (or ended depending
upon chipset). Before then, one has to look at the BIOS memory maps to
find the Top of Memory. Alas that is not exported by arch/x86 and so we
have to resort to disabling stolen memory on gen2 for the time being.

Then SandyBridge enlarged the PCI register to a full 32-bits and change
the encoding of the address, so even though we happened to be querying
the right register, we read the wrong bits and ended up using address 0
for our stolen data, i.e. notably FBC.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm: Introduce an iterator over holes in the drm_mm range manager

This will be used i915 in forthcoming patches in order to measure the
largest contiguous chunk of memory available for enabling chipset
features.

v2: Try to make the macro marginally safer and more readable by not
depending upon the drm_mm_hole_node_end() being non-zero. Note that we
need to open code list_for_each() in order to update the hole_start,
hole_end variable on each iteration and keep the macro sane.

v3: Tidy up few BUG_ONs that fell foul of adding additional tests to
drm_mm_hole_node_start().

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Airlie <airlied@redhat.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm: Introduce drm_mm_create_block()

To be used later by i915 to preallocate exact blocks of space from the
range manager.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Airlie <airlied@redhat.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: optimize ilk/snb irq handler

We only need to read/write the south interrupt register if the
corresponding bit is set in the north master interrupt register.
Noticed while reading our interrupt handling code.

Same optimization has already been applied on ivb in

commit 0e43406bcc1868a316eea6012a0a09d992c53521
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Wed May 9 21:45:44 2012 +0100

    drm/i915: Simplify interrupt processing for IvyBridge

    We can take advantage that the PCH_IIR is a subordinate register to
    reduce one of the required IIR reads, and that we only need to clear
    interrupts handled to reduce the writes. And by simply tidying the code
    we can reduce the line count and hopefully make it more readable.

Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

i915: convert struct spinlock to spinlock_t

spinlock_t should always be used.

  LD      drivers/gpu/drm/i915/built-in.o
  CHECK   drivers/gpu/drm/i915/i915_drv.c
  CC [M]  drivers/gpu/drm/i915/i915_drv.o
  CHECK   drivers/gpu/drm/i915/i915_dma.c
  CC [M]  drivers/gpu/drm/i915/i915_dma.o
  CHECK   drivers/gpu/drm/i915/i915_irq.c
  CC [M]  drivers/gpu/drm/i915/i915_irq.o
  CHECK   drivers/gpu/drm/i915/i915_debugfs.c
drivers/gpu/drm/i915/i915_debugfs.c:558:31: warning: dereference of noderef expression
drivers/gpu/drm/i915/i915_debugfs.c:558:39: warning: dereference of noderef expression
drivers/gpu/drm/i915/i915_debugfs.c:558:51: warning: dereference of noderef expression
drivers/gpu/drm/i915/i915_debugfs.c:558:63: warning: dereference of noderef expression
  CC [M]  drivers/gpu/drm/i915/i915_debugfs.o
  CHECK   drivers/gpu/drm/i915/i915_suspend.c
  CC [M]  drivers/gpu/drm/i915/i915_suspend.o
  CHECK   drivers/gpu/drm/i915/i915_gem.c
drivers/gpu/drm/i915/i915_gem.c:3703:14: warning: incorrect type in assignment (different base types)
drivers/gpu/drm/i915/i915_gem.c:3703:14:    expected unsigned int [unsigned] [usertype] mask
drivers/gpu/drm/i915/i915_gem.c:3703:14:    got restricted gfp_t
drivers/gpu/drm/i915/i915_gem.c:3706:22: warning: invalid assignment: &=
drivers/gpu/drm/i915/i915_gem.c:3706:22:    left side has type unsigned int
drivers/gpu/drm/i915/i915_gem.c:3706:22:    right side has type restricted gfp_t
drivers/gpu/drm/i915/i915_gem.c:3707:22: warning: invalid assignment: |=
drivers/gpu/drm/i915/i915_gem.c:3707:22:    left side has type unsigned int
drivers/gpu/drm/i915/i915_gem.c:3707:22:    right side has type restricted gfp_t
drivers/gpu/drm/i915/i915_gem.c:3711:39: warning: incorrect type in argument 2 (different base types)
drivers/gpu/drm/i915/i915_gem.c:3711:39:    expected restricted gfp_t [usertype] mask
drivers/gpu/drm/i915/i915_gem.c:3711:39:    got unsigned int [unsigned] [usertype] mask
  CC [M]  drivers/gpu/drm/i915/i915_gem.o
  CHECK   drivers/gpu/drm/i915/i915_gem_context.c
  CC [M]  drivers/gpu/drm/i915/i915_gem_context.o
  CHECK   drivers/gpu/drm/i915/i915_gem_debug.c
  CC [M]  drivers/gpu/drm/i915/i915_gem_debug.o
  CHECK   drivers/gpu/drm/i915/i915_gem_evict.c
  CC [M]  drivers/gpu/drm/i915/i915_gem_evict.o
  CHECK   drivers/gpu/drm/i915/i915_gem_execbuffer.c
  CC [M]  drivers/gpu/drm/i915/i915_gem_execbuffer.o
  CHECK   drivers/gpu/drm/i915/i915_gem_gtt.c
  CC [M]  drivers/gpu/drm/i915/i915_gem_gtt.o
  CHECK   drivers/gpu/drm/i915/i915_gem_stolen.c
  CC [M]  drivers/gpu/drm/i915/i915_gem_stolen.o
  CHECK   drivers/gpu/drm/i915/i915_gem_tiling.c
  CC [M]  drivers/gpu/drm/i915/i915_gem_tiling.o
  CHECK   drivers/gpu/drm/i915/i915_sysfs.c
  CC [M]  drivers/gpu/drm/i915/i915_sysfs.o
  CHECK   drivers/gpu/drm/i915/i915_trace_points.c
  CC [M]  drivers/gpu/drm/i915/i915_trace_points.o
  CHECK   drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_display.c:1736:9: warning: mixing different enum types
drivers/gpu/drm/i915/intel_display.c:1736:9:     int enum transcoder  versus
drivers/gpu/drm/i915/intel_display.c:1736:9:     int enum pipe
drivers/gpu/drm/i915/intel_display.c:3659:48: warning: mixing different enum types
drivers/gpu/drm/i915/intel_display.c:3659:48:     int enum pipe  versus
drivers/gpu/drm/i915/intel_display.c:3659:48:     int enum transcoder
  CC [M]  drivers/gpu/drm/i915/intel_display.o
  CHECK   drivers/gpu/drm/i915/intel_crt.c
  CC [M]  drivers/gpu/drm/i915/intel_crt.o
  CHECK   drivers/gpu/drm/i915/intel_lvds.c
  CC [M]  drivers/gpu/drm/i915/intel_lvds.o
  CHECK   drivers/gpu/drm/i915/intel_bios.c
drivers/gpu/drm/i915/intel_bios.c:706:60: warning: incorrect type in initializer (different address spaces)
drivers/gpu/drm/i915/intel_bios.c:706:60:    expected struct vbt_header *vbt
drivers/gpu/drm/i915/intel_bios.c:706:60:    got void [noderef] <asn:2>*vbt
drivers/gpu/drm/i915/intel_bios.c:726:42: warning: incorrect type in argument 1 (different address spaces)
drivers/gpu/drm/i915/intel_bios.c:726:42:    expected void const *<noident>
drivers/gpu/drm/i915/intel_bios.c:726:42:    got unsigned char [noderef] [usertype] <asn:2>*
drivers/gpu/drm/i915/intel_bios.c:727:40: warning: cast removes address space of expression
drivers/gpu/drm/i915/intel_bios.c:738:24: warning: cast removes address space of expression
  CC [M]  drivers/gpu/drm/i915/intel_bios.o
  CHECK   drivers/gpu/drm/i915/intel_ddi.c
drivers/gpu/drm/i915/intel_ddi.c:87:6: warning: symbol 'intel_prepare_ddi_buffers' was not declared. Should it be static?
drivers/gpu/drm/i915/intel_ddi.c:1036:34: warning: mixing different enum types
drivers/gpu/drm/i915/intel_ddi.c:1036:34:     int enum pipe  versus
drivers/gpu/drm/i915/intel_ddi.c:1036:34:     int enum transcoder
  CC [M]  drivers/gpu/drm/i915/intel_ddi.o
drivers/gpu/drm/i915/intel_ddi.c: In function ‘intel_ddi_setup_hw_pll_state’:
drivers/gpu/drm/i915/intel_ddi.c:1129:2: warning: ‘port’ may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/gpu/drm/i915/intel_ddi.c:1111:12: note: ‘port’ was declared here
  CHECK   drivers/gpu/drm/i915/intel_dp.c
  CC [M]  drivers/gpu/drm/i915/intel_dp.o
  CHECK   drivers/gpu/drm/i915/intel_hdmi.c
  CC [M]  drivers/gpu/drm/i915/intel_hdmi.o
  CHECK   drivers/gpu/drm/i915/intel_sdvo.c
  CC [M]  drivers/gpu/drm/i915/intel_sdvo.o
  CHECK   drivers/gpu/drm/i915/intel_modes.c
  CC [M]  drivers/gpu/drm/i915/intel_modes.o
  CHECK   drivers/gpu/drm/i915/intel_panel.c
  CC [M]  drivers/gpu/drm/i915/intel_panel.o
  CHECK   drivers/gpu/drm/i915/intel_pm.c
drivers/gpu/drm/i915/intel_pm.c:2173:1: warning: symbol 'mchdev_lock' was not declared. Should it be static?
  CC [M]  drivers/gpu/drm/i915/intel_pm.o
  CHECK   drivers/gpu/drm/i915/intel_i2c.c
  CC [M]  drivers/gpu/drm/i915/intel_i2c.o
  CHECK   drivers/gpu/drm/i915/intel_fb.c
  CC [M]  drivers/gpu/drm/i915/intel_fb.o
  CHECK   drivers/gpu/drm/i915/intel_tv.c
  CC [M]  drivers/gpu/drm/i915/intel_tv.o
  CHECK   drivers/gpu/drm/i915/intel_dvo.c
  CC [M]  drivers/gpu/drm/i915/intel_dvo.o
  CHECK   drivers/gpu/drm/i915/intel_ringbuffer.c
  CC [M]  drivers/gpu/drm/i915/intel_ringbuffer.o
  CHECK   drivers/gpu/drm/i915/intel_overlay.c
  CC [M]  drivers/gpu/drm/i915/intel_overlay.o
  CHECK   drivers/gpu/drm/i915/intel_sprite.c
  CC [M]  drivers/gpu/drm/i915/intel_sprite.o
  CHECK   drivers/gpu/drm/i915/intel_opregion.c
  CC [M]  drivers/gpu/drm/i915/intel_opregion.o
  CHECK   drivers/gpu/drm/i915/dvo_ch7xxx.c
  CC [M]  drivers/gpu/drm/i915/dvo_ch7xxx.o
  CHECK   drivers/gpu/drm/i915/dvo_ch7017.c
  CC [M]  drivers/gpu/drm/i915/dvo_ch7017.o
  CHECK   drivers/gpu/drm/i915/dvo_ivch.c
  CC [M]  drivers/gpu/drm/i915/dvo_ivch.o
  CHECK   drivers/gpu/drm/i915/dvo_tfp410.c
  CC [M]  drivers/gpu/drm/i915/dvo_tfp410.o
  CHECK   drivers/gpu/drm/i915/dvo_sil164.c
  CC [M]  drivers/gpu/drm/i915/dvo_sil164.o
  CHECK   drivers/gpu/drm/i915/dvo_ns2501.c
  CC [M]  drivers/gpu/drm/i915/dvo_ns2501.o
  CHECK   drivers/gpu/drm/i915/i915_gem_dmabuf.c
  CC [M]  drivers/gpu/drm/i915/i915_gem_dmabuf.o
  CHECK   drivers/gpu/drm/i915/i915_ioc32.c
  CC [M]  drivers/gpu/drm/i915/i915_ioc32.o
  CHECK   drivers/gpu/drm/i915/intel_acpi.c
  CC [M]  drivers/gpu/drm/i915/intel_acpi.o
  LD [M]  drivers/gpu/drm/i915/i915.o
  Building modules, stage 2.
  MODPOST 1 modules
  CC      drivers/gpu/drm/i915/i915.mod.o
  LD [M]  drivers/gpu/drm/i915/i915.ko

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: intel-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: kill intel_dp_link_clock()

Use drm_dp_bw_code_to_link_rate insead. It's the same thing, but
supports DP_LINK_BW_5_4 and is also used by the other drivers.

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: invert the log inside intel_prepare_ddi

Do an early return in case we don't have DDI instead of having the
whole function inside an "if" statement.

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: add HAS_DDI check

And use it whenever we call code that uses the DDIs. We already have
intel_ddi.c and prefix every function with intel_ddi_something instead of
haswell_something, so I think replacing the checks with HAS_DDI makes more
sense. Just a cosmetical change, yes I know, but I have this OCD...

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: remove Haswell code from ironlake_fdi_pll_enable

This function is not called on Haswell anymore.

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: intel_prepare_ddi_buffers should be static

It's not even declared on header files.

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: optimize the shmem_pwrite slowpath handling

Since we drop dev->struct_mutex when going through the slowpath, the
object might have been moved out of the cpu domain. Hence we need to
clflush the entire object to ensure that after the ioctl returns,
everything is coherent again (interwoven writes are ill-defined
anyway).

But we only need to do this if we start in the cpu domain and the
object requires flushing for coherency. So don't do the flushing if
the object is coherent anyway or if we've done in-line clfushing
already.

v2: i915_gem_clflush_object already checks whether the object is
coherent and if so, drops the flushing. Hence we don't need to check
that ourselves, simplifying the condition.

v3: Reorder the checks for better clarity (and adjust the comment
accordingly), suggested by Chris Wilson.

Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: simplify shmem pwrite/pread slowpath handling

The shmem paths for pwrite/pread used a clever trick to hold onto a
single page when dropping the big dev->struct_mutex for the slowpath.
But this ran the risk of reinstating (or not completely purging) the
backing storage when dropping purgeable objects.

Hence the code needed to keep track of whether it ever dropped the
lock, and if it did, manually check whether it needs to re-purge the
backing storage. But thanks to the pages pin count introduced in

commit a5570178c059cec59e9835be20bc8546377fa7b5
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Tue Sep 4 21:02:54 2012 +0100

    drm/i915: Pin backing pages whilst exporting through a dmabuf vmap

which allowed us to pin the backing storage and remove that page
reference trick from shmem_pwrite/read in

commit f60d7f0c1d55a935475ab394955cafddefaa6533
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Tue Sep 4 21:02:56 2012 +0100

    drm/i915: Pin backing pages for pread

and

commit 755d22184f1e5015b040acee794542d9cf8a16c5
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Tue Sep 4 21:02:55 2012 +0100

    drm/i915: Pin backing pages for pwrite

we can now abolish this check. The slowpath cleanup completely
disappears from pread, and for pwrite we're only left with the domain
fixup in case someone moved the object out of the cpu domain from
under us. A follow-on patch will optimize that a notch more.

Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: enable intel_lvds->pre_pll_enable for ilk+, too

Only two things needed adjustment:
- pipe select for PCH_CPT
- There's no dithering bit on ilk+ in the lvds ctl reg

Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: move intel_update_lvds to intel_lvds->pre_pll_enable

A few things needed to change:
- HAS_PCH_SPLIT since ilk+ is not yet converted to this.
- s/LVDS/intel_lvds->reg/ to prep for ilk conversion
- replace the clock.p2 == 7 check with a is_dual_link check
- s/adjusted_mode/intel_lvds->fixed_mode

v2: Rebase on top of Jani Nikula's panel rework. I'm wondering whether
we shouldn't add an attached_panel pointer to intel_encoder, to
replace the encoder private ->attached_connector pointers, since
that's essentially what we need.

Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: add intel_lvds->reg

To ditch at least some of the PCH_SPLIT ? PCH_LVDS : LVDS code ...

v2: Rebase on top of Jani Nikula's panel rework.

Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: track is_dual_link in intel_lvds

Yeah, all users (both the clock selection special cases and the lvds
pin pair stuff) are still in common code, but this will change.

v2: Rebase on top of Jani Nikula's panel rework.

v3: Incorporate review from Paulo Zanoni:
- s/__is_dual_link_lvds/compute_is_dual_link_lvds
- kill dev_priv->lvds_val
- drop spurious whitespace change

v4: Add a debug printk to display the dual-link status, as suggested
by Paulo Zanoni in review.

Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v3)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: move is_dual_link_lvds to intel_lvds.c

Just a prep patch to make this a property of intel_lvds. Makes more
sense, removes clutter from intel_display.c and eventually I want to
move all the encoder special cases wrt clock handling to encoders
anyway.

v2: Add an intel_ prefixe to is_dual_link_lvds since it's non-static
now.

Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: replace ad-hoc dual-link lvds checks

... with is_dual_link_lvds introduced in

commit b03543857fd75876b96e10d4320b775e95041bb7
Author: Takashi Iwai <tiwai@suse.de>
Date:   Tue Mar 20 13:07:05 2012 +0100

    drm/i915: Check VBIOS value for determining LVDS dual channel mode, too

All these checks predate this commit and have simply been overlooked.
Since we don't support switching between single-link and dual-link
modes anyway, this different checks could at best only get in the way
of refactorings, and in the worst case cause inconsistencies.

v2: Update the comment, we now have a solid way to figure out whether
we need dual-link lvds or not (falling back to vbt values as a last
resort). We still don't know how to switch between dual-link and
single link so leave that part intact. I'm not sure though whether
switching between these two modes makes any sense - we always drive
the panel at its fixed mode (with a fixed bpc) anyway ...

Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: add encoder->pre_pll_enable callback

Currently we have two encoder specific bits in the common mode_set
functions:
- lvds pin pair enabling
- dp m/n setting and computation

Now the lvds stuff needs to happen before the pll is enabled. Since
that is done in the crtc_mode_set functions, we need to add a new
callback to be able to move them to the encoder code (where they
belong). The dp m/n stuff is a giant mess anyway (since it also
confuses itself with the fdi link m/n handling), so that needs to be
handled separately.

I think that we can move the pll enabling down quite a bit, which
might allow us to eventually merge encoder->pre_enable with this new
pre_pll_enable callback. But for now this will allow us to clean
things up a bit.

Note that vlv doesn't support lvds, hence we don't need to change
anything in there.

v2: Fixup commit message, both suggested from Paulo Zanoni.
- dp m/n doesn't need to happen before pll enabling
- lvds doesn't exist on vlv, hence no changes required in the vlv pll
  function.

Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/debugfs: Prune a couple of superfluous leading zeros from bo domains

As we do not have any domains occupying the high bits, there is no point
in always printing the leading 00.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Kill i915_gem_execbuffer_wait_for_flips()

As per Chris Wilson's suggestion make
i915_gem_execbuffer_wait_for_flips() go away.

This was used to stall the GPU ring while there are pending
page flips involving the relevant BO. Ie. while the BO is still
being scanned out by the display controller.

The recommended alternative is to use the page flip events to
wait for the page flips to fully complete before reusing the BO
of the old front buffer. Or use more buffers.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Kristian Høgsberg <krh@bitplanet.net>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: don't remove obj->pending_flips, still required due to
reorder patches.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: remove duplicate register #defines

Somehow a chunk of unused register defines ended up in the middle of
the PLL defines. They go back to the original kms merging.

The only used #define is SR01, move it to the register name together
with the other legacy vga stuff.

Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Set sync_seqno properly after seqno wrap

i915_gem_handle_seqno_wrap() will zero all sync_seqnos but as the
wrap can happen inside ring->sync_to(), pre wrap seqno was
carried over and overwrote the zeroed sync_seqno.

When wrap is handled, all outstanding requests will be retired and
objects moved to inactive queue, causing their last_read_seqno to be zero.
Use this to update the sync_seqno correctly.

RING_SYNC registers after wrap will contain pre wrap values which
are >= seqno. So injecting the semaphore wait into ring completes
immediately.

Original idea for using last_read_seqno from Chris Wilson.

Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Include the last semaphore sync point in the error-state

Should be useful to know what the driver thought the other ring's seqno
was when it last used a semaphore.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Rearrange code to only have a single method for waiting upon the ring

Replace the wait for the ring to be clear with the more common wait for
the ring to be idle. The principle advantage is one less exported
intel_ring_wait function, and the removal of a hardcoded value.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Simplify flushing activity on the ring

As we now always preallocate the seqno before writing to the ring, we
can trivially test if we have any pending activity on the ring by
inspecting the olr. This makes it then possible to flush operations that
are not normally associated with a request, like power-management.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Preallocate next seqno before touching the ring

Based on the work by Mika Kuoppala, we realised that we need to handle
seqno wraparound prior to committing our changes to the ring. The most
obvious point then is to grab the seqno inside intel_ring_begin(), and
then to reuse that seqno for all ring operations until the next request.
As intel_ring_begin() can fail, the callers must already be prepared to
handle such failure and so we can safely add further checks.

This patch looks like it should be split up into the interface
changes and the tweaks to move seqno wrapping from the execbuffer into
the core seqno increment. However, I found no easy way to break it into
incremental steps without introducing further broken behaviour.

v2: Mika found a silly mistake and a subtle error in the existing code;
inside i915_gem_retire_requests() we were resetting the sync_seqno of
the target ring based on the seqno from this ring - which are only
related by the order of their allocation, not retirement. Hence we were
applying the optimisation that the rings were synchronised too early,
fortunately the only real casualty there is the handling of seqno
wrapping.

v3: Do not forget to reset the sync_seqno upon module reinitialisation,
ala resume.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=863861
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> [v2]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: force restore on lid open

There seem to be indeed some awkwards machines around, mostly those
without OpRegion support, where the firmware changes the display hw
state behind our backs when closing the lid.

This force-restore logic has been originally introduced in

commit c1c7af60892070e4b82ad63bbfb95ae745056de0
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date:   Thu Sep 10 15:28:03 2009 -0700

    drm/i915: force mode set at lid open time

but after the modeset-rework we've disabled it in the vain hope that
it's no longer required:

commit 3b7a89fce3e3dc96b549d6d829387b4439044d0d
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Mon Sep 17 22:27:21 2012 +0200

    drm/i915: fix OOPS in lid_notify

Alas, no.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=54677
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=57434
Tested-by: Krzysztof Mazur <krzysiek@podlesie.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Wait upon the last request seqno, rather than a future seqno

In commit 69c2fc891343cb5217c866d10709343cff190bdc
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Fri Jul 20 12:41:03 2012 +0100

    drm/i915: Remove the per-ring write list

the explicit flush was removed from i915_ring_idle(). However, we
continued to wait upon the next seqno which now did not correspond to
any request (except for the unusual condition of a failure to queue a
request after execbuffer) and so would wait indefinitely.

This has an important side-effect that i915_gpu_idle() does not cause
the seqno to be incremented. This is vital if we are to be able to idle
the GPU to handle seqno wraparound, as in subsequent patches.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: fix possible NULL dereference of dev_priv

Dereference dev_priv only after we know it is valid.
Found with smatch.

Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Increase the response time for slow SDVO devices

Some devices may respond very slowly and only flag that the reply is
pending within the first 15us response window. Be kind to such devices
and wait a further 15ms, before checking for the pending reply. This
moves the existing special case delay of 30ms down from the detection
routine into the common path and pretends to explain it...

v2: Simplify the loop constructs as suggested by Jani Nikula.

References: https://bugs.freedesktop.org/show_bug.cgi?id=36997
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: set the VIC of the mode on the AVI InfoFrame

We currently set "0" as the VIC value of the AVI InfoFrames. According
to the specs this should be fine and work for every mode, so to my
point of view we can't consider the current behavior as a bug. The
problem is that  we recently received a bug report (Kernel bug #50371)
from a user that has an AV receiver that gives a black screen for any
mode with VIC set to 0.

So in order to make at least some modes work for him, this patch sets
the correct VIC number when sending AVI InfoFrames.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=50371
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm: add drm_mode_cea_vic

This function returns the VIC of the mode. This value can be used when
creating AVI InfoFrames.

Cc: Thierry Reding <thierry.reding@avionic-design.de>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=50371
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Fix pte updates in ggtt clear range

This bug was introduced by me:
commit e76e9aebcdbfebae8f4cd147e3c0f800d36e97f3
Author: Ben Widawsky <ben@bwidawsk.net>
Date:   Sun Nov 4 09:21:27 2012 -0800

    drm/i915: Stop using AGP layer for GEN6+

The existing code uses memset_io which follows memset semantics in only
guaranteeing a write of individual bytes. Since a PTE entry is 4 bytes,
this can only be correct if the scratch page address is 0.

This caused unsightly errors when we clear the range at load time,
though I'm not really sure what the heck is referencing that memory
anyway. I caught this is because I believe we have some other bug where
the display is doing reads of memory we feel should be cleared (or we
are relying on scratch pages to be a specific value).

Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: promote Haswell to full support

Since it should be working a little bit better now.

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Report the origin of the LVDS fixed panel mode

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: resolve conflict around the call to intel_crtc_mode_get. And
add the missing NULL check Chris spotted while at it.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: LVDS fallback to fixed-mode if EDID not present

Use the recorded panel fixed-mode to populate the get_modes() request in
the absence of an EDID.

Fixes regression from
commit 9cd300e038d492af4990b04e127e0bd2df64b1ca
Author: Jani Nikula <jani.nikula@intel.com>
Date:   Fri Oct 19 14:51:52 2012 +0300

    drm/i915: Move cached EDID to intel_connector

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Drop the retval-changing hunk, as suggested by Jani in his
review and acked by Chris.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/sdvo: kfree the intel_sdvo_connector, not drm_connector, on destroy

Since the base fields in both struct intel_connector and struct
intel_sdvo_connector are at the beginning of the enclosing struct, the
pointers are essentially the same, but there is no requirement or guarantee
that this is always the case. Kfree the enclosing intel_sdvo_connector
pointer that was originally allocated, not the enclosed drm_connector, in
case someone ever rearranges the structs.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: drm_connector_property -> drm_object_property

v2: Rebased.

Signed-off-by: Rob Clark <rob@ti.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com> (v1)
[danvet: Pimp commit message a bit.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: use drm_send_vblank_event() helper

Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Use pci_resource functions for BARs.

This was leftover crap from kill-agp. The current code is theoretically
broken for 64b bars. (I resist removing theoretically because I am too
lazy to test).

We still need to ioremap things ourselves because we want to ioremap_wc
the PTEs.

v2: Forgot to kill the tmp variable in v1

CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Borrow our struct_mutex for the direct reclaim

If we have hit oom whilst holding our struct_mutex, then currently we
cannot reap our own GPU buffers which likely pin most of memory, making
an outright OOM more likely. So if we are running in direct reclaim and
already hold the mutex, attempt to free buffers knowing that the
original function can not continue until we return.

v2: Add a note explaining that the mutex may be stolen due to
pre-emption, and that is bad.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Defer assignment of obj->gtt_space until after all possible mallocs

As we may invoke the shrinker whilst trying to allocate memory to hold
the gtt_space for this object, we need to be careful not to mark the
drm_mm_node as activated (by assigning it to this object) before we
have finished our sequence of allocations.

Note: We also need to move the binding of the object into the actual
pagetables down a bit. The best way seems to be to move it out into
the callsites.

Reported-by: Imre Deak <imre.deak@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Added small note to commit message to summarize review
discussion.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Apply the IBX transcoder A w/a for HDMI to SDVO as well

As the SDVO/HDMI registers are multiplex, it is safe to assume that the
w/a required for HDMI on IbexPoint, namely that the SDVO register cannot
both be disabled and have selected transcoder B, is also required for
SDVO. At least the modeset state checker detects that the transcoder
selection is left in the undefined state, and so it appears sensible to
apply the w/a:

[ 1814.480052] WARNING: at drivers/gpu/drm/i915/intel_display.c:1487 assert_pch_hdmi_disabled+0xad/0xb5()
[ 1814.480053] Hardware name: Libretto W100
[ 1814.480054] IBX PCH hdmi port still using transcoder B

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=57066
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: implement WaMbcDriverBootEnable on Haswell

Also document the WA name for the previous gens that implement it.

Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: fix intel_ddi_get_cdclk_freq for ULT machines

For now, this code is just used by the eDP AUX channel frequency.

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: make the panel fitter work on pipes B and C on Haswell

This goes on a separate patch since it won't apply on the stable
trees and there's nothing using panel fitter on HSW on the older
Kernels.

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: make the panel fitter work on pipes B and C on IVB

I actually found this problem on Haswell, but then discovered Ivy
Bridge also has it by reading the spec.

I don't have the hardware to test this.

Cc: stable@vger.kernel.org
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: don't intel_crt_init if DDI A has 4 lanes

DDI A and E have 4 lanes to share, so if DDI A is using 4 lanes,
there's nothing left for DDI E, which means there's no CRT port on the
machine.

The bit we're checking here is programmed at system boot and it cannot
be changed afterwards, so we cannot change the amount of lanes
reserved for each DDI port.

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: make DP work on LPT-LP machines

We need to enable a special bit, otherwise none of the DP functions
requiring the PCH will work.

Version 2: store the PCH ID inside dev_priv, as suggested by Daniel
Vetter.

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: fix false positive "Unclaimed write" messages

We don't check if the "unclaimed register" bit is set before we call
writel, so if it was already set before, we might print a misleading
message about "unclaimed write" on the wrong register.

This patch makes us check the unclaimed bit before the writel, so we
can print a new "Unknown unclaimed register before writing to %x"
message.

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: use cpu/pch transcoder on intel_enable_pipe

This function runs on Haswell, so set the correct pch_transcoder and
cpu_transcoder variables. This fixes an assertion failure on Haswell
VGA.

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: don't limit Haswell CRT encoder to pipe A

This is a full revert of 59c859d6f2e78344945e8a8406a194156176bc4e:
    drm/i915: account for only one PCH receiver on Haswell

Now that the PCH code is fixed to be able use the only PCH transcoder
independently of the pipe and CPU transcoder, we can revert this.

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Resolve conflict due to the rebasing of dinq on top of
drm-next.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Flush outstanding unpin tasks before pageflipping

If we accumulate unpin tasks because we are pageflipping faster than the
system can schedule its workers, we can effectively create a
pin-leak. The solution taken here is to limit the number of unpin tasks
we have per-crtc and to flush those outstanding tasks if we accumulate
too many. This should prevent any jitter in the normal case, and also
prevent the hang if we should run too fast.

Note: It is important that we switch from the system workqueue to our
own dev_priv->wq since all work items on that queue are guaranteed to
only need the dev->struct_mutex and not any modeset resources. For
otherwise if we have a work item ahead in the queue which needs the
modeset lock (like the output detect work used by both polling or
hpd), this work and so the unpin work will never execute since the
pageflip code already holds that lock. Unfortunately there's no
lockdep support for this scenario in the workqueue code.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=46991
Reported-and-tested-by: Tvrtko Ursulin <tvrtko.ursulin@onelan.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Added note about workqueu deadlock.]
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=56337
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: resurrect panel lid handling

But disabled by default. This essentially reverts

commit bcd5023c961a44c7149936553b6929b2b233dd27
Author: Dave Airlie <airlied@redhat.com>
Date:   Mon Mar 14 14:17:55 2011 +1000

    drm/i915: disable opregion lid detection for now

but leaves the autodetect mode disabled. There's also the explicit lid
status option added in

commit fca874092597ef946b8f07031d8c31c58b212144
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Thu Feb 17 13:44:48 2011 +0000

    drm/i915: Add a module parameter to ignore lid status

Which overloaded the meaning for the panel_ignore_lid parameter even
more. To fix up this mess, give the non-negative numbers 0,1 the
original meaning back and use negative numbers to force a given state.
So now we have

1  - disable autodetect, return unknown
0  - enable autodetect
-1 - force to disconnected/lid closed
-2 - force to connected/lid open

v2: My C programmer license has been revoked ...

v3: Beautify the code a bit, as suggested by Chris Wilson.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=27622
Tested-by: Andreas Sturmlechner <andreas.sturmlechner@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Enable DP audio for Haswell

This patch adds the missing code to send ELD for Haswell DisplayPort,
based on Xingchao's original patch.

A test was performed with HSW-D machine and NEC EA232Wmi DP monitor.

Cc: Xingchao Wang <xingchao.wang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Pin the object whilst faulting it in

In order to prevent reaping of the object whilst setting it up to
handle the pagefault, we need to mark it as pinned. This has the nice
side-effect of eliminating some special cases from the pagefault handler
as well!

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Guard pages being reaped by OOM whilst binding-to-GTT

In the circumstances that the shrinker is allowed to steal the mutex
in order to reap pages, we need to be careful to prevent it operating on
the current object and shooting ourselves in the foot.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Remove bogus test for a present execbuffer

The intention of checking obj->gtt_offset!=0 is to verify that the
target object was listed in the execbuffer and had been bound into the
GTT. This is guarranteed by the earlier rearrangement to split the
execbuffer operation into reserve and relocation phases and then
verified by the check that the target handle had been processed during
the reservation phase.

However, the actual checking of obj->gtt_offset==0 is bogus as we can
indeed reference an object at offset 0. For instance, the framebuffer
installed by the BIOS often resides at offset 0 - causing EINVAL as we
legimately try to render using the stolen fb.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Remove save/restore of physical HWS_PGA register

Now that we always restore the HWS registers (both physical and GTT
virtual addresses) when re-initialising the rings, we can eliminate the
superfluous save/restore of the register across suspend and resume.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Fix warning in i915_gem_chipset_flush

drivers/gpu/drm/i915/i915_drv.h:1545:2: warning: '______f' is static but
declared in inline function 'i915_gem_chipset_flush' which is not static

Reported-by: kbuild test robot <fengguang.wu@intel.com>
dri-devel-Reference: <50a4d41c.586VhmwghPuKZbkB%fengguang.wu@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Only check for valid PP_{ON, OFF}_DELAYS on pre ILK hardware

ILK+ have this register on the PCH. This check was triggering unclaimed
writes.

Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: drop buggy write to FDI_RX_CHICKEN register

Jani Nikula noticed that the parentheses are wrong and we & the bit
with the register address instead of the read-back value. He sent a
patch to correct that.

On second look, we write the same register in the previous line, and
the w/a seems to be to set FDI_RX_PHASE_SYNC_POINTER_OVR to enable the
logic, then keep always set FDI_RX_PHASE_SYNC_POINTER_OVR and toggle
FDI_RX_PHASE_SYNC_POINTER_EN before/after enabling the pc transcoder.

So the right things seems to be to simply kill the 2nd write.

Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Dropped a bogus ~ from the commit message that somehow crept
in.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Use LRI to update the semaphore registers

The bspec was recently updated to remove the ability to update the
semaphore using the MI_SEMAPHORE_BOX command, the ability to wait upon
the semaphore value remained. Instead the advice is to update the
register using the MI_LOAD_REGISTER_IMM command. In cursory testing,
semaphores continue to function - the question is whether this fixes
some of the deadlocks where the semaphore registers contained stale
values?

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel J Blueman <daniel@quora.org>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: add LynxPoint-LP PCH ID

[pzanoni: rebase, print it's an LP PCH]

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Optimize DIV_ROUND_CLOSEST call

DIV_ROUND_CLOSEST is faster if the compiler knows it will only be
dealing with unsigned dividends. This optimization rips 32 bytes of
binary code on x86_64.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/vmwgfx: Make vmw_dmabuf_unreference handle NULL objects

Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/vmwgfx: Refactor module load to not require fifo unless fbdev is loaded

This also fixes a bug where the fence manager was left without irq
enabled when waiting for fences, causing various errors at module
load time

Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/vmwgfx: Make screen object code not require fifo at init time

Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/vmwgfx: Make overlay code not require fifo at init time

Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/vmwgfx: Enable traces *after* we've hidden SVGA

Hiding SVGA seems to trigger a VGA screen clear, and with no
traces dirty it doesn't seem to repaint

Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/ttm: alter cpu_writers to return -EBUSY in ttm_execbuf_util reservations

This is similar to other platforms that don't allow command submission
to buffers locked on the cpu.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/ttm: Optimize reservation slightly

Reservation locking currently always takes place under the LRU spinlock.
Hence, strictly there is no need for an atomic_cmpxchg call; we can use
atomic_read followed by atomic_write since nobody else will ever reserve
without the lru spinlock held.
At least on Intel this should remove a locked bus cycle on successful
reserve.

Note that thit commit may be obsoleted by the cross-device reservation work.

Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/ttm, drm/vmwgfx: Use RCU locking for object lookups v3

The mostly used lookup+get put+potential_destroy path of TTM objects
is converted to use RCU locks. This will substantially decrease the amount
of locked bus cycles during normal operation.
Since we use kfree_rcu to free the objects, no rcu synchronization is needed
at module unload time.

v2: Don't touch include/linux/kref.h
v3: Adapt to kref_get_unless_zero return value change

Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

kref: Implement kref_get_unless_zero v3

This function is intended to simplify locking around refcounting for
objects that can be looked up from a lookup structure, and which are
removed from that lookup structure in the object destructor.
Operations on such objects require at least a read lock around
lookup + kref_get, and a write lock around kref_put + remove from lookup
structure. Furthermore, RCU implementations become extremely tricky.
With a lookup followed by a kref_get_unless_zero *with return value check*
locking in the kref_put path can be deferred to the actual removal from
the lookup structure and RCU lookups become trivial.

v2: Formatting fixes.
v3: Invert the return value.

Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm: Make hashtab rcu-safe

TTM base objects will be the first consumer.

Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/ttm: remove sync_arg from driver functions

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-By: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/ttm: remove sync_obj_arg from ttm_bo_move_accel_cleanup

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-By: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/ttm: remove sync_obj_arg member

vmwgfx was its only user and always sets it to the same..

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-By: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/vmwgfx: remove use of fence_obj_args

It's always hardcoded to the same value.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-By: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

DRM/KMS: Add Bail-Out Conditions for Loop.

When trying to obtain an accurate timestamp for the last vsync interrupt
in vblank_disable_and_save() we loop until the vsync counter after reading
the time stamp is identical to the one before.
In the case where no hardware timestamp can be obtained there is probably
no point in trying to make sure we remain within the same vsync during
the time we obtain the counter.
Furthermore we should make sure there's an 'emergency exit' so that we
don't end up in an endless loop when the driver get_vblank_timestamp()
function doesn't manage to return within the same vsync.
This may happen when this function prints out debugging information over
a slow (ie serial) line.

Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm: don't unnecessarily enable the polling work

... by properly checking connector->polled. This doesn't matter too
much because the polling work itself gets this slightly more right and
doesn't set repoll if there's nothing to do. But we can do better.

v2: Chris Wilson noticed that I broke polling, since repoll will never
ever be set true. Fix this up, and simplify the logic a bit while at
it.

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>

vga_switcheroo: Drop unused include and unused variables.

Signed-off-by: Igor Murzov <e-mail@date.by>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/nouveau: free memory allocated with alloc_apertures()

Fix a memory leak by deallocating the memory we got from
alloc_apertures().

Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/radeon: check alloc_apertures() success in radeon_kick_out_firmware_fb()

Check for alloc_apertures() memory allocation failure, and propagate an
error code in case the allocation failed.

Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/mgag200: remove unneeded aper->count assignment after alloc_apertures()

alloc_apertures() already does the assignment for us, so assigning the
count member after the alloc_apertures() call is not needed.

Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/mgag200: free memory allocated with alloc_apertures()

Fix a memory leak by deallocating the memory we got from
alloc_apertures().

Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/mgag200: check alloc_apertures() success in mga_vram_init()

Check for alloc_apertures() memory allocation failure, and propagate an
error code in case the allocation failed.

Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/cirrus: check alloc_apertures() success in cirrus_kick_out_firmware_fb()

Check for alloc_apertures() memory allocation failure, and propagate an
error code in case the allocation failed.

Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/ttm: remove ttm_mem_global->queue

It's unused.

Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/ttm: remove ttm_bo_device->nice_mode

It's unused.

Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/ttm: remove ttm_buffer_object->buffer_start

All drivers set it to 0 and nothing uses it.

Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/radeon: Use hweight32

Use hweight32 instead of counting for each bit

Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm: use memchr_inv()

Use memchr_inv() to check the specified memory region is filled with zero.

Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm: add support for monotonic vblank timestamps

Jumps in the vblank and page flip event timestamps cause trouble for
clients, so we should avoid them. The timestamp we get currently with
gettimeofday can jump, so use instead monotonic timestamps.

For backward compatibility use a module flag to revert back to using
gettimeofday timestamps. Add also a DRM_CAP_TIMESTAMP_MONOTONIC flag
that is simply a read only version of the module flag, so that clients
can query this without depending on sysfs.

Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>