ide: add cable detection for early UDMA66 devices (take 3)
* Move ide_in_drive_list() from ide-dma.c to ide-iops.c.
* Add ivb_list[] table for listening early UDMA66 devices which don't conform
to ATA4 standard wrt cable detection (bit14 is zero, only bit13 is valid)
and use only device side cable detection for them since host side cable
detection may be unreliable.
* Add model "QUANTUM FIREBALLlct10 05" with firwmare "A03.0900" to the list
(from Craig's bugreport).
v2:
* Improve kernel message basing on suggestion from Sergei.
v3:
* Don't print kernel message when no device side cable detection is done,
plus some minor fixes. (Noticed by Sergei)
* Add DMA blacklist checking (->ide_dma_on check probably can go now).
* Add ->atapi_dma flag checking and remove no longer needed
ns87415_ide_dma_check() from ns87415 host driver.
* Remove now needless __ide_dma_check() wrapper and symbol export.
* Check drive->autodma instead of hwif->autodma (there should be no changes in
behavior as all users of config_drive_for_dma() set both ->autodma flags).
ide: fix hidden dependencies on CONFIG_IDE_GENERIC
Some host drivers depend on CONFIG_IDE_GENERIC to do the probing but their
config options lack explicit dependencies on IDE_GENERIC. In the long-term
these host drivers should be fixed to do the probing themselves but for now
fix them by making their config options select CONFIG_IDE_GENERIC.
Tejun Heo [Mon, 20 Aug 2007 20:42:53 +0000 (22:42 +0200)]
ide: make CONFIG_IDE_GENERIC default to N
These days, CONFIG_IDE_GENERIC causes more confusion and
misconfiguration than it helps. Especially so because libata is
linked after the generic driver. Default to N.
Chris Wright [Sat, 18 Aug 2007 21:31:41 +0000 (14:31 -0700)]
x86: properly initialize temp insn buffer for paravirt patching
With commit ab144f5ec64c42218a555ec1dbde6b60cf2982d6 the patching code
now collects the complete new instruction stream into a temp buffer
before finally patching in the new insns. In some cases the paravirt
patchers will choose to leave the patch site unpatched (length mismatch,
clobbers mismatch, etc).
This causes the new patching code to copy an uninitialized temp buffer,
i.e. garbage, to the callsite. Simply make sure to always initialize
the buffer with the original instruction stream. A better fix is to
audit all the patchers and return proper length so that apply_paravirt()
can skip copies when we leave the patch site untouched.
Signed-off-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andi Kleen [Wed, 15 Aug 2007 00:40:36 +0000 (02:40 +0200)]
x86_64: Change PMDS invocation to single macro
Very old binutils (2.12.90...) seem to have trouble with newlines
in assembler macro invocation. They put them into the resulting
argument expansion. In this case this lead to a parse error because
a .rept expression ended up spread over multiple lines. Change the PMDS()
invocation to a single line.
Daniel Gollub [Wed, 15 Aug 2007 00:40:35 +0000 (02:40 +0200)]
x86_64: Fix to keep watchdog disabled by default for i386/x86_64
Fixed wrong expression which enabled watchdogs even if nmi_watchdog kernel
parameter wasn't set. This regression got slightly introduced with commit b7471c6da94d30d3deadc55986cc38d1ff57f9ca.
Introduced NMI_DISABLED (-1) which allows to switch the value of NMI_DEFAULT
without breaking the APIC NMI watchdog code (again).
Fixes:
https://bugzilla.novell.com/show_bug.cgi?id=298084
http://bugzilla.kernel.org/show_bug.cgi?id=7839
And likely some more nmi_watchdog=0 related issues.
Andi Kleen [Wed, 15 Aug 2007 00:40:34 +0000 (02:40 +0200)]
x86_64: Fail dma_alloc_coherent on dma less devices
This should fix an oops with PCMCIA PATA devices
http://bugzilla.kernel.org/show_bug.cgi?id=8424
This is not a full fix for the problem, but probably
still the right thing to do.
[ I'm almost certain it's *not* the right thing to do, but it avoids an
oops, and I want comments from others on what the right thing would
actually be.. I suspect we should just remove the use of dma_mask
entirely in this function, and just use coherent_dma_mask. - Linus ]
Timo Jantunen [Tue, 14 Aug 2007 18:56:57 +0000 (21:56 +0300)]
fix random hang in forcedeth driver when using netconsole
If the forcedeth driver receives too much work in an interrupt, it
assumes it has a broken hardware with stuck IRQ. It works around the
problem by disabling interrupts on the nic but makes a printk while
holding device spinlog - which isn't smart thing to do if you have
netconsole on the same nic.
This patch moves the printk's out of the spinlock protected area.
Without this patch the machine hangs hard. With this patch everything
still works even when there is significant increase on CPU usage while
using the nic.
Signed-off-by: Timo Jantunen <jeti@iki.fi> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Satyam Sharma [Thu, 16 Aug 2007 00:39:25 +0000 (06:09 +0530)]
i386: Fix a couple busy loops in mach_wakecpu.h:wait_for_init_deassert()
Use cpu_relax() in the busy loops, as atomic_read() doesn't automatically
imply volatility for i386 and x86_64. x86_64 doesn't have this issue because
it open-codes the while loop in smpboot.c:smp_callin() itself that already
uses cpu_relax().
For i386, however, smpboot.c:smp_callin() calls wait_for_init_deassert()
which is buggy for mach-default and mach-es7000 cases.
[ I test-built a kernel -- smp_callin() itself got inlined in its only
callsite, smpboot.c:start_secondary() -- and the relevant piece of
code disassembles to the following:
0xc1019704 <start_secondary+12>: mov 0xc144c4c8,%eax
0xc1019709 <start_secondary+17>: test %eax,%eax
0xc101970b <start_secondary+19>: je 0xc1019709 <start_secondary+17>
init_deasserted (at 0xc144c4c8) gets fetched into %eax only once and
then we loop over the test of the stale value in the register only,
so these look like real bugs to me. With the fix below, this becomes:
Linus Torvalds [Sat, 18 Aug 2007 16:38:56 +0000 (09:38 -0700)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
Cross-compilation between e.g. i386 -> 64bit could break -> work around it
[IA64] Enable early console for Ski simulator
[IA64] forbid ptrace changes psr.ri to 3
[IA64] Failure to grow RBS
[IA64] Fix processor_get_freq
[IA64] SGI Altix : fix a force_interrupt bug on altix
[IA64] Update arch/ia64/configs/* s/SLAB/SLUB/
[IA64] get back PT_IA_64_UNWIND program header
[IA64] need NOTES in vmlinux.lds.S
[IA64] make unwinder stop at last frame of the bootloader
[IA64] Clean up CPE handler registration
[IA64] Include Kconfig.preempt
[IA64] SN2 needs platform specific irq_to_vector() function.
[IA64] Use atomic64_read to read an atomic64_t.
[IA64] disable irq's and check need_resched before safe_halt
Linus Torvalds [Sat, 18 Aug 2007 16:38:09 +0000 (09:38 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Incorrect semicolon after if statement
mlx4_core: Wait 1 second after reset before accessing device
IPoIB: Fix leak in ipoib_transport_dev_init() error path
IB/mlx4: Fix opcode returned in RDMA read completion
IB/srp: Add OUI for new Cisco targets
IB/srp: Wrap OUI checking for workarounds in helper functions
RDMA/cxgb3: Always call low level send function via cxgb3_ofld_send()
IB: Move the macro IB_UMEM_MAX_PAGE_CHUNK() to umem.c
IB: Include <linux/list.h> and <linux/rwsem.h> from <rdma/ib_verbs.h>
IB: Include <linux/list.h> from <rdma/ib_mad.h>
IB/mad: Fix address handle leak in mad_rmpp
IB/mad: agent_send_response() should be void
IB/mad: Fix memory leak in switch handling in ib_mad_recv_done_handler()
IB/mad: Fix error path if response alloc fails in ib_mad_recv_done_handler()
IB/sa: Don't need to check for default P_Key twice
IB/core: Ignore membership bit in ib_find_pkey()
Linus Torvalds [Sat, 18 Aug 2007 16:34:28 +0000 (09:34 -0700)]
Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[MATH-EMU]: Fix underflow exception reporting.
[SPARC64]: Create a HWCAP_SPARC_N2 and report it to userspace on Niagara-2.
[SPARC64]: SMP trampoline needs to avoid %tick_cmpr on sun4v too.
[SPARC64]: Do not touch %tick_cmpr on sun4v cpus.
[SPARC64]: Niagara-2 optimized copies.
[SPARC64]: Allow userspace to get at the machine description.
[SPARC32]: Remove superfluous 'kernel_end' alignment on sun4c.
[SPARC32]: Fix bogus ramdisk image location check.
[SPARC32]: Remove iommu from struct sbus_bus and use archdata like sparc64.
Linus Torvalds [Sat, 18 Aug 2007 16:33:25 +0000 (09:33 -0700)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Fix invalid semicolon after if statement
[POWERPC] ps3: Fix no storage devices found
[POWERPC] Fix for assembler -g
[POWERPC] Fix small race in 44x tlbie function
[POWERPC] Remove unused code causing a compile warning
[POWERPC] cell: Fix errno for modular spufs_create with invalid neighbour
Linus Torvalds [Sat, 18 Aug 2007 16:31:05 +0000 (09:31 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setup
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setup:
[x86 setup] edd.c: make sure MBR signatures actually get reported
[x86 setup] Don't use EDD to get the MBR signature
[x86 setup] The current display page is returned in %bh, not %bl
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] Check return code on failed alloc
[CIFS] Update CIFS project web site
[CIFS] Fix hang in find_writable_file
Marcel Holtmann [Fri, 17 Aug 2007 19:47:58 +0000 (21:47 +0200)]
Reset current->pdeath_signal on SUID binary execution
This fixes a vulnerability in the "parent process death signal"
implementation discoverd by Wojciech Purczynski of COSEINC PTE Ltd.
and iSEC Security Research.
Thomas Renninger [Thu, 16 Aug 2007 14:27:15 +0000 (16:27 +0200)]
Cross-compilation between e.g. i386 -> 64bit could break -> work around it
Adrian Bunk: scripts/mod/file2alias.c is compiled with HOSTCC and ensures that
kernel_ulong_t is correct, but it can't cope with different padding on
different architectures.
Signed-off-by: Thomas Renninger <trenn@suse.de> Signed-off-by: Tony Luck <tony.luck@intel.com>
Shaohua Li [Fri, 17 Aug 2007 20:43:50 +0000 (13:43 -0700)]
[IA64] forbid ptrace changes psr.ri to 3
The "ri" field in the processor status register only has defined
values of 0, 1, 2. Do not let ptrace set this to 3. As with
other reserved fields in registers we silently discard the value.
Signed-off-by: Shaohua Li <shaohua.li@intel.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
David S. Miller [Fri, 17 Aug 2007 05:59:49 +0000 (22:59 -0700)]
[MATH-EMU]: Fix underflow exception reporting.
The underflow exception cases were wrong.
This is one weird area of ieee1754 handling in that the underflow
behavior changes based upon whether underflow is enabled in the trap
enable mask of the FPU control register. As a specific case the Sparc
V9 manual gives us the following description:
--------------------
If UFM = 0: Underflow occurs if a nonzero result is tiny and a
loss of accuracy occurs. Tininess may be detected
before or after rounding. Loss of accuracy may be
either a denormalization loss or an inexact result.
If UFM = 1: Underflow occurs if a nonzero result is tiny.
Tininess may be detected before or after rounding.
--------------------
What this amounts to in the packing case is if we go subnormal,
we set underflow if any of the following are true:
1) rounding sets inexact
2) we ended up rounding back up to normal (this is the case where
we set the exponent to 1 and set the fraction to zero), this
should set inexact too
3) underflow is set in FPU control register trap-enable mask
The initially discovered example was "DBL_MIN / 16.0" which
incorrectly generated an underflow. It should not, unless underflow
is set in the trap-enable mask of the FPU csr.
Another example, "0x0.0000000000001p-1022 / 16.0", should signal both
inexact and underflow. The cpu implementations and ieee1754
literature is very clear about this. This is case #2 above.
However, if underflow is set in the trap enable mask, only underflow
should be set and reported as a trap. That is handled properly by the
prioritization logic in
Ilpo Järvinen [Wed, 15 Aug 2007 22:03:35 +0000 (08:03 +1000)]
[POWERPC] Fix invalid semicolon after if statement
A similar fix to netfilter from Eric Dumazet inspired me to
look around a bit by using some grep/sed stuff as looking for
this kind of bugs seemed easy to automate. This is one of them
I found where it looks like this semicolon is not valid.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Andrew Burgess [Thu, 16 Aug 2007 17:30:46 +0000 (10:30 -0700)]
[IA64] Failure to grow RBS
There is a bug in the ia64_do_page_fault code that can cause a failure
to grow the register backing store, or any mapping that is marked as
VM_GROWSUP if the mapping is the highest mapped area of memory.
When the address accessed is below the first mapping the previous mapping
is returned as NULL, and this case is handled. However, when the address
accessed is above the highest mapping the vma returned is NULL, this
case is not handled correctly, and it fails to spot that this access
might require an existing mapping to grow upwards.
Signed-off-by: Andrew Burgess <andrew@transitive.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
Andy Whitcroft [Thu, 16 Aug 2007 16:25:34 +0000 (01:25 +0900)]
sh: remove extraneous ; on scif_sercon_putc wait loop
It seems we have gained an extraneous trailing ';' on one of the
wait loops in scif_sercon_putc(). Although this is completely
benign as the apparent payload is also the empty statement, it
invites error in the future. Clean it up now.
Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Ilpo Järvinen [Wed, 15 Aug 2007 22:07:30 +0000 (15:07 -0700)]
[IPv6]: Invalid semicolon after if statement
A similar fix to netfilter from Eric Dumazet inspired me to
look around a bit by using some grep/sed stuff as looking for
this kind of bugs seemed easy to automate. This is one of them
I found where it looks like this semicolon is not valid.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Williamson [Mon, 13 Aug 2007 21:49:46 +0000 (15:49 -0600)]
[IA64] Fix processor_get_freq
The core cpufreq code doesn't appear to understand returning -EAGAIN
for the get() function of the cpufreq_driver. If PAL_GET_PSTATE returns
-1, such as when running on Xen, scaling_cur_freq is happy to return 4294967285 kHz (ie. (unsigned)-11). The other drivers appear to return
0 for a failure, and doing so gives me the max frequency from
scaling_cur_frequency and "<unknown>" from cpuinfo_cur_frequency. I
believe that's the desired behavior.
Signed-off-by: Alex Williamson <alex.williamson@hp.com> Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
Add empty definition of mmiowb() since some drivers need it. Uncached
writes are strongly ordered on AVR32. They may be delayed if the
dcache is busy doing a writeback, but AFAICT that's not what this
macro is supposed to deal with, at least on UP systems.
We might have to revisit this definition when a SMP-capable AVR32 CPU
comes along, depending on how the busses and cache coherency stuff
end up being implemented.
The current definition of pte_page() masks out valid bits from the
physical address, causing vmalloc_to_page() to misbehave. This may
lead to everything from mmap() silently accessing the wrong data to
"invalid pte" errors dumped by the kernel.
Also remove the now-unused definition of PTE_PHYS_MASK.
There's really no need to retry an allocation with __GFP_REPEAT set.
Also, use get_zeroed_page() and __GFP_ZERO to eliminate the extra call
to clear_page() afterwards.
The NGW100 has a board controller which is hooked up to the TWI lines
on AP7000. Since the TWI driver isn't in mainline, use the i2c-gpio
driver in the mean time.
Ryan Power [Fri, 10 Aug 2007 20:59:35 +0000 (13:59 -0700)]
libata: adjust libata to ignore errors after spinup
Adjust libata to ignore errors after spinup
This patch is to ignore errors from the spinup attempt if the drive is
in the "standby id" state.
Signed-off-by: Ryan Power <rpower@sysreset.com> Acked-by: Mark Lord <liml@rtr.ca> Cc: Jeff Garzik <jeff@garzik.org> Cc: Tejun Heo <htejun@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Sergei Shtylyov [Fri, 10 Aug 2007 17:02:15 +0000 (21:02 +0400)]
pata_hpt{37x|3x2n}: fix clock reporting (take 2)
Fix several inconsistencies in these drivers WRT reporting the clocks:
- when using DPLL mode, 'pata_hpt37x' driver reported the DPLL frequency as the
PCI clock -- make it properly report both clocks and add the same ability to
the 'pata_hpt3x2n' driver;
- both drivers sometimes use "pata_hpt3*:" and sometimes "hpt3*:" in the
messages -- make them use only the former one;
- the message about failed DPLL stablizatios deserves KERN_ERR and a bang. :-)
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Sergei Shtylyov [Fri, 10 Aug 2007 16:58:46 +0000 (20:58 +0400)]
pata_hpt37x: actually clock HPT374 with 50 MHz DPLL (take 2)
The DPLL tuning code always set up it for 66 MHz due to wrong UltraDMA mask
including mode 5 used to check for the necessity of 66 MHz clocking -- this
caused 66 MHz clock to be used for HPT374 chip that does not tolerate it.
While fixing this, also remove PLL mode from the TODO list -- I don't think
it's still a relevant item.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Roland McGrath [Fri, 10 Aug 2007 23:03:11 +0000 (09:03 +1000)]
[POWERPC] Fix for assembler -g
ppc64 does the unusual thing of using #include on a compiler-generated
assembly file (lparmap.s) from an assembly source file (head_64.S).
This runs afoul of my recent patch to pass -gdwarf2 to the assembler
under CONFIG_DEBUG_INFO. This patch avoids the problem by disabling
DWARF generation (-g0) when producing lparmap.s.
Signed-off-by: Roland McGrath <roland@redhat.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
David Gibson [Tue, 7 Aug 2007 04:20:50 +0000 (14:20 +1000)]
[POWERPC] Fix small race in 44x tlbie function
The 440 family of processors don't have a tlbie instruction. So, we
implement TLB invalidates by explicitly searching the TLB with tlbsx.,
then clobbering the relevant entry, if any. Unfortunately the PID for
the search needs to be stored in the MMUCR register, which is also
used by the TLB miss handler. Interrupts were enabled in _tlbie(), so
an interrupt between loading the MMUCR and the tlbsx could cause
incorrect search results, and thus a failure to invalide TLB entries
which needed to be invalidated.
This fixes the problem in both arch/ppc and arch/powerpc by inhibiting
interrupts (even critical and debug interrupts) across the relevant
instructions.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Becky Bruce [Fri, 11 May 2007 17:49:39 +0000 (03:49 +1000)]
[POWERPC] Remove unused code causing a compile warning
AFAICT, nobody is using ft_ordered(), and it causes a build warning
to be generated. This patch cleans that up by removing the function
and the commented-out code that calls it.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com> Acked-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Mark Fortescue [Wed, 15 Aug 2007 01:24:10 +0000 (18:24 -0700)]
[SPARC32]: Remove superfluous 'kernel_end' alignment on sun4c.
In sun4c_init_clean_mmu(), aligning 'kernel_end' using
SUN4C_REAL_PGDIR_ALIGN() is unnecessary since the caller
does this already.
In sun4c_paging_init(), 4 page sizes of "fluff" were added
to the address of &end. This was necessary a long time ago
when sparc32 would allocate some early data structures
by carving out memory chunks after &end but that no longer
occurs.
Signed-off-by: Mark Fortescue <mark@mtfhpc.demon.co.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
H. Peter Anvin [Wed, 15 Aug 2007 00:36:00 +0000 (17:36 -0700)]
[x86 setup] edd.c: make sure MBR signatures actually get reported
When filling in the MBR signature array, the setup code failed to advance
boot_params.edd_mbr_sig_buf_entries, which resulted in the valid data
being ignored.
H. Peter Anvin [Mon, 13 Aug 2007 23:27:42 +0000 (16:27 -0700)]
[x86 setup] Don't use EDD to get the MBR signature
At least one machine has been identified in the field which advertises
EDD for all drives but locks up if one attempts an extended read from
a non-primary drive.
The MBR is always at CHS 0-0-1, so there is no reason to use an
extended read, other than the possibility that the BIOS cannot handle
it.
Although this might break as many machines as it fixes (a small number
either way), the current state is a regression but the reverse is not.
Therefore revert to the previous state of not using extended read.
Quite probably the Right Thing to do is to read using plain (CHS) read
and extended read on failure, but that change would definitely have to
go through -mm first.
Shannon Nelson [Wed, 15 Aug 2007 00:36:31 +0000 (17:36 -0700)]
[IOAT]: Remove redundant struct member to avoid descriptor cache miss
The layout for struct ioat_desc_sw is non-optimal and causes an extra
cache hit for every descriptor processed. By tightening up the struct
layout and removing one item, we pull in the fields that get used in
the speedpath and get a little better performance.
Alexey Dobriyan [Wed, 15 Aug 2007 00:24:05 +0000 (17:24 -0700)]
[AX25]: don't free pointers to statically allocated data
commit 8d5cf596d10d740b69b5f4bbdb54b85abf75810d started to add statically
allocated ax25_protocol's to list. However kfree() was still in place waiting
for unsuspecting ones on module removal.
Steps to reproduce:
modprobe netrom
rmmod netrom
P.S.: code would benefit greatly from list_add/list_del usage
H. Peter Anvin [Fri, 10 Aug 2007 21:20:26 +0000 (14:20 -0700)]
[x86 setup] The current display page is returned in %bh, not %bl
The current display page is an 8-bit number, even though struct
screen_info gives it a 16-bit number. The number is returned in %bh,
so it needs to be >> 8 before storing.
Special thanks to Jeff Chua for detailed bug reporting.
Jussi Kivilinna [Tue, 14 Aug 2007 20:22:58 +0000 (13:22 -0700)]
[BRIDGE]: Fix typo in net/bridge/br_stp_if.c
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Acked-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
The stp change code generates "sleeping function called from invalid
context" because rtnl_lock() called with BH disabled. This fixes it by
not acquiring then dropping the bridge lock.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 14 Aug 2007 20:13:28 +0000 (13:13 -0700)]
[NETFILTER]: netfilter: xt_u32 bug correction
An extraneous ";" makes xt_u32 match useless
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes:
[GFS2] Revert remounting w/o acl option leaves acls enabled
[GFS2] Fix setting of inherit jdata attr
[GFS2] Fix incorrect error path in prepare_write()
[GFS2] Fix incorrect return code in rgrp.c
[GFS2] soft lockup in rgblk_search
[GFS2] soft lockup detected in databuf_lo_before_commit
[DLM] fix basts for granted PR waiting CW
[DLM] More othercon fixes
[DLM] Fix memory leak in dlm_add_member() when dlm_node_weight() returns less than zero
[DLM] zero unused parts of sockaddr_storage
[DLM] fix NULL ls usage
[DLM] Clear othercon pointers when a connection is closed
Linus Torvalds [Tue, 14 Aug 2007 16:52:12 +0000 (09:52 -0700)]
Merge branch 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c-s3c2410: Build fix
i2c/menelaus: Build fix
i2c-mv64xxx: Reinitialize hw and driver on I2C bus hang
i2c-mpc: Don't disable I2C module on stop condition
i2c-iop3xx: Set I2C_CLASS_HWMON to adapter class
i2c/isp1301_omap: Build fixes, whitespace
i2c-mpc: Pass correct dev_id to free_irq on error path
i2c-i801: Typo: erroneous
Dale Farnsworth [Tue, 14 Aug 2007 16:37:14 +0000 (18:37 +0200)]
i2c-mv64xxx: Reinitialize hw and driver on I2C bus hang
Under certain conditions, the mv64xxx I2C bus can hang preventing
further operation. To make the driver more robust, we now reset
the I2C hardware and the driver state machine when such hangs are
detected.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org> Acked-by: Mark A. Greer <mgreer@mvista.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
David Brownell [Tue, 14 Aug 2007 16:37:14 +0000 (18:37 +0200)]
i2c/isp1301_omap: Build fixes, whitespace
Build fixes for isp1301_omap driver. I think an earlier version
of this must have gotten lost somewhere, or maybe it only went
into the Linux-OMAP tree.
Also, some whitespace fixes to bring this more into sync with the
version of this found in the Linux-OMAP tree. (That version has
updates for the OTG controller on the OMAP 1710 which break that
functionality on OMAP 161x boards like the H2, so merging all of
it is not currently an option.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Jean Delvare <khali@linux-fr.org>
projects / linux-beck.git / log