Adrian Hunter [Thu, 7 May 2015 10:10:22 +0000 (13:10 +0300)]
mmc: core: Flag re-tuning is needed on CRC errors
CRC errors could possibly be alleviated by
re-tuning so flag re-tuning needed in those cases.
Note this has no effect if re-tuning has not been
enabled.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adrian Hunter [Thu, 7 May 2015 10:10:21 +0000 (13:10 +0300)]
mmc: sdhci: Change to new way of doing re-tuning
Make use of mmc core support for re-tuning instead
of doing it all in the sdhci driver.
This patch also changes to flag the need for re-tuning
always after runtime suspend when tuning has been used
at initialization. Previously it was only done if
the re-tuning timer was in use.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adrian Hunter [Thu, 7 May 2015 10:10:20 +0000 (13:10 +0300)]
mmc: core: Add support for HS400 re-tuning
HS400 re-tuning must be done in HS200 mode. Add
the ability to switch from HS400 mode to HS200
mode before re-tuning and switch back to HS400
after re-tuning.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adrian Hunter [Thu, 7 May 2015 10:10:14 +0000 (13:10 +0300)]
mmc: core: Add support for re-tuning before each request
At the start of each request, re-tune if needed and
then hold off re-tuning again until the request is done.
Note that though there is one function that starts
requests (mmc_start_request) there are two that wait for
the request to be done (mmc_wait_for_req_done and
mmc_wait_for_data_req_done). Also note that
mmc_wait_for_data_req_done can return even when the
request is not done (which allows the block driver
to prepare a newly arrived request while still
waiting for the previous request).
This patch ensures re-tuning is held for the duration
of a request. Subsequent patches will also hold
re-tuning at other times when it might cause a
conflict.
In addition, possibly a command is failing because
re-tuning is needed. Use mmc_retune_recheck() to check
re-tuning. At that point re-tuning is held, at least by
the request, so mmc_retune_recheck() flags host->retune_now
if the hold count is 1.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adrian Hunter [Thu, 7 May 2015 10:10:13 +0000 (13:10 +0300)]
mmc: core: Enable / disable re-tuning
Enable re-tuning when tuning is executed and
disable re-tuning when card is no longer initialized.
In the case of SDIO suspend, the card can keep power.
In that case, re-tuning need not be disabled, but, if
a re-tuning timer is being used, ensure it is disabled
and assume that re-tuning will be needed upon resume
since it is not known how long the suspend will last.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adrian Hunter [Thu, 7 May 2015 10:10:12 +0000 (13:10 +0300)]
mmc: host: Add facility to support re-tuning
Currently, there is core support for tuning during
initialization. There can also be a need to re-tune
periodically (e.g. sdhci) or to re-tune after the
host controller is powered off (e.g. after PM
runtime suspend / resume) or to re-tune in response
to CRC errors.
The main requirements for re-tuning are:
- ability to enable / disable re-tuning
- ability to flag that re-tuning is needed
- ability to re-tune before any request
- ability to hold off re-tuning if the card is busy
- ability to hold off re-tuning if re-tuning is in
progress
- ability to run a re-tuning timer
To support those requirements 7 members are added to struct
mmc_host:
unsigned int can_retune:1; /* re-tuning can be used */
unsigned int doing_retune:1; /* re-tuning in progress */
unsigned int retune_now:1; /* do re-tuning at next req */
int need_retune; /* re-tuning is needed */
int hold_retune; /* hold off re-tuning */
unsigned int retune_period; /* re-tuning period in secs */
struct timer_list retune_timer; /* for periodic re-tuning */
need_retune is an integer so it can be set without needing
synchronization. hold_retune is a integer to allow nesting.
Various simple functions are provided to set / clear those
variables.
Subsequent patches take those functions into use.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Weijun Yang [Mon, 27 Apr 2015 08:15:13 +0000 (08:15 +0000)]
mmc: sdhci-sirf: fix the tuning count in platform_execute_tuning
hardware has 16bit to record the tuning count, so fix it to 16384.
at the same time, tuned_phases[SIRF_TUNING_COUNT] is useless as the
array is never used, so move it to a variant.
Signed-off-by: Weijun Yang <Weijun.Yang@csr.com> Signed-off-by: Barry Song <Baohua.Song@csr.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc: sh_mmcif: separate sh_mmcif_clk_update() into setup and prepare
Current sh_mmcif_clk_update() is called from probe() and set_ios(),
but, the purpose of later one is just clk_prepare_enable().
No need to setup mmc->f_max/f_min in many times.
This patch separe sh_mmcif_clk_update() into clk_prepare_enable()
and mmc->f_max/f_min setup.
mmc: sh_mmcif: remove unnecessary int clk from struct sh_mmcif_host
struct sh_mmcif_host has 1) int clk, 2) struct clock *hclk,
and host->clk = clk_get_rate(host->hclk).
This int clk is not necessary. Let's remove it.
And, current hclk is confusable naming. Let's rename it to clk.
Andreas Fenkart [Thu, 23 Apr 2015 11:15:42 +0000 (13:15 +0200)]
mmc: sdio: add reset callback to bus operations
Some drivers schedule automatic hw resets. An example is mwifiex,
which schedules a card reset if the command handler between driver
and card firmware becomes out of sync
Signed-off-by: Andreas Fenkart <afenkart@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Linus Torvalds [Sun, 24 May 2015 18:15:28 +0000 (11:15 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of five fixes: Two MAINTAINER email updates (urgent
because the non-avagotech emails will start bouncing) an lpfc big
endian oops fix, a 256 byte sector hang fix (to eliminate 256 byte
sectors) and a storvsc fix which could cause test unit ready failures
on bringup"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
MAINTAINERS: Revise lpfc maintainers for Avago Technologies ownership of Emulex
MAINTAINERS, be2iscsi: change email domain
sd: Disable support for 256 byte/sector disks
lpfc: Fix breakage on big endian kernels
storvsc: Set the SRB flags correctly when no data transfer is needed
Linus Torvalds [Sat, 23 May 2015 18:28:25 +0000 (11:28 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull two Ceph fixes from Sage Weil:
"These fix an issue with the RBD notifications when there are topology
changes in the cluster"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
Revert "libceph: clear r_req_lru_item in __unregister_linger_request()"
libceph: request a new osdmap if lingering request maps to no osd
Linus Torvalds [Sat, 23 May 2015 18:14:10 +0000 (11:14 -0700)]
Merge branch 'for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"I fixed up a regression from 4.0 where conversion between different
raid levels would sometimes bail out without converting.
Filipe tracked down a race where it was possible to double allocate
chunks on the drive.
Mark has a fix for fiemap. All three will get bundled off for stable
as well"
* 'for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix regression in raid level conversion
Btrfs: fix racy system chunk allocation when setting block group ro
btrfs: clear 'ret' in btrfs_check_shared() loop
Linus Torvalds [Sat, 23 May 2015 00:34:24 +0000 (17:34 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Radeon has two displayport fixes, one for a regression.
i915 regression flicker fix needed so 4.0 can get fixed.
A bunch of msm fixes and a bunch of exynos fixes, these two are
probably a bit larger than I'd like, but most of them seems pretty
good"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (29 commits)
drm/radeon: fix error flag checking in native aux path
drm/radeon: retry dcpd fetch
drm/msm/mdp5: fix incorrect parameter for msm_framebuffer_iova()
drm/exynos: dp: Lower level of EDID read success message
drm/exynos: cleanup exynos_drm_plane
drm/exynos: 'win' is always unsigned
drm/exynos: mixer: don't dump registers under spinlock
drm/exynos: Consolidate return statements in fimd_bind()
drm/exynos: Constify exynos_drm_crtc_ops
drm/exynos: Fix build breakage on !DRM_EXYNOS_FIMD
drm/exynos: mixer: Constify platform_device_id
drm/exynos: mixer: cleanup pixelformat handling
drm/exynos: mixer: also allow NV21 for the video processor
drm/exynos: mixer: remove buffer count handling in vp_video_buffer()
drm/exynos: plane: honor buffer offset for dma_addr
drm/exynos: fb: use drm_format_num_planes to get buffer count
drm/i915: fix screen flickering
drm/msm: fix locking inconsistencies in gpu->destroy()
drm/msm/dsi: Simplify the code to get the number of read byte
drm/msm: Attach assigned encoder to eDP and DSI connectors
...
1) Don't leak ipvs->sysctl_tbl, from Tommi Rentala.
2) Fix neighbour table entry leak in rocker driver, from Ying Xue.
3) Do not emit bonding notifications for unregistered interfaces, from
Nicolas Dichtel.
4) Set ipv6 flow label properly when in TIME_WAIT state, from Florent
Fourcot.
5) Fix regression in ipv6 multicast filter test, from Henning Rogge.
6) do_replace() in various footables netfilter modules is missing a
check for 0 counters in the datastructure provided by the user. Fix
from Dave Jones, and found with trinity.
7) Fix RCU bug in packet scheduler classifier module unloads, from
Daniel Borkmann.
8) Avoid deadlock in tcp_get_info() by using u64_sync. From Eric
Dumzaet.
9) Input packet processing can race with inetdev_destroy() teardown,
fix potential OOPS in ip_error() by explicitly testing whether the
inetdev is still attached. From Eric W Biederman.
10) MLDv2 parser in bridge multicast code breaks too early while
parsing. Fix from Thadeu Lima de Souza Cascardo.
11) Asking for settings on non-zero PHYID doesn't work because we do not
import the command structure from the user and use the PHYID
provided there. Fix from Arun Parameswaran.
12) Fix UDP checksums with IPV6 RAW sockets, from Vlad Yasevich.
13) Missing NF_TABLES depends for TPROXY etc can cause build failures,
fix from Florian Westphal.
14) Fix netfilter conntrack to handle RFC5961 challenge ACKs properly,
from Jesper Dangaard Brouer.
15) If netlink autobind retry fails, we have to reset the sockets portid
back to zero. From Herbert Xu.
16) VXLAN netns exit code unregisters using wrong device, from John W
Linville.
17) Add some USB device IDs to ath3k and btusb bluetooth drivers, from
Dmitry Tunin and Wen-chien Jesse Sung.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
bridge: fix lockdep splat
net: core: 'ethtool' issue with querying phy settings
bridge: fix parsing of MLDv2 reports
ARM: zynq: DT: Use the zynq binding with macb
net: macb: Disable half duplex gigabit on Zynq
net: macb: Document zynq gem dt binding
ipv4: fill in table id when replacing a route
cdc_ncm: Fix tx_bytes statistics
ipv4: Avoid crashing in ip_error
tcp: fix a potential deadlock in tcp_get_info()
net: sched: fix call_rcu() race on classifier module unloads
net: phy: Make sure phy_start() always re-enables the phy interrupts
ipv6: fix ECMP route replacement
ipv6: do not delete previously existing ECMP routes if add fails
Revert "netfilter: bridge: query conntrack about skb dnat"
netfilter: ensure number of counters is >0 in do_replace()
netfilter: nfnetlink_{log,queue}: Register pernet in first place
tcp: don't over-send F-RTO probes
tcp: only undo on partial ACKs in CA_Loss
net/ipv6/udp: Fix ipv6 multicast socket filter regression
...
Linus Torvalds [Fri, 22 May 2015 22:15:30 +0000 (15:15 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Three small fixes that have been picked up the last few weeks.
Specifically:
- Fix a memory corruption issue in NVMe with malignant user
constructed request. From Christoph.
- Kill (now) unused blk_queue_bio(), dm was changed to not need this
anymore. From Mike Snitzer.
- Always use blk_schedule_flush_plug() from the io_schedule() path
when flushing a plug, fixing a !TASK_RUNNING warning with md. From
Shaohua"
* 'for-linus' of git://git.kernel.dk/linux-block:
sched: always use blk_schedule_flush_plug in io_schedule_out
nvme: fix kernel memory corruption with short INQUIRY buffers
block: remove export for blk_queue_bio
Linus Torvalds [Fri, 22 May 2015 21:49:55 +0000 (14:49 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"Updates for the input subsystem.
The main change is that we tell joydev not to touch "absolute mice",
such as VMware virtual mouse, as that produced bad result (cursor
stuck in upper right corner) with games"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: smtpe-ts - wait 50mS until polling for pen-up
Input: smtpe-ts - use msecs_to_jiffies() instead of HZ
Input: joydev - don't classify the vmmouse as a joystick
Input: vmmouse - do not reference non-existing version of X driver
Input: alps - fix finger jumps on lifting 2 fingers on v7 touchpad
Input: elantech - fix semi-mt protocol for v3 HW
Input: sx8654 - fix memory allocation check
Problem here is that br_forward_delay_timer_expired() is a timer
handler, calling br_ifinfo_notify() which assumes either rcu_read_lock()
or RTNL are held.
Simplest fix seems to add rcu read lock section.
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Josh Boyer <jwboyer@fedoraproject.org> Reported-by: Dominick Grift <dac.override@gmail.com> Cc: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: core: 'ethtool' issue with querying phy settings
When trying to configure the settings for PHY1, using commands
like 'ethtool -s eth0 phyad 1 speed 100', the 'ethtool' seems to
modify other settings apart from the speed of the PHY1, in the
above case.
The ethtool seems to query the settings for PHY0, and use this
as the base to apply the new settings to the PHY1. This is
causing the other settings of the PHY 1 to be wrongly
configured.
The issue is caused by the '_ethtool_get_settings()' API, which
gets called because of the 'ETHTOOL_GSET' command, is clearing
the 'cmd' pointer (of type 'struct ethtool_cmd') by calling
memset. This clears all the parameters (if any) passed for the
'ETHTOOL_GSET' cmd. So the driver's callback is always invoked
with 'cmd->phy_address' as '0'.
The '_ethtool_get_settings()' is called from other files in the
'net/core'. So the fix is applied to the 'ethtool_get_settings()'
which is only called in the context of the 'ethtool'.
Signed-off-by: Arun Parameswaran <aparames@broadcom.com> Reviewed-by: Ray Jui <rjui@broadcom.com> Reviewed-by: Scott Branden <sbranden@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When more than a multicast address is present in a MLDv2 report, all but
the first address is ignored, because the code breaks out of the loop if
there has not been an error adding that address.
This has caused failures when two guests connected through the bridge
tried to communicate using IPv6. Neighbor discoveries would not be
transmitted to the other guest when both used a link-local address and a
static address.
This only happens when there is a MLDv2 querier in the network.
The fix will only break out of the loop when there is a failure adding a
multicast address.
The mdb before the patch:
dev ovirtmgmt port vnet0 grp ff02::1:ff7d:6603 temp
dev ovirtmgmt port vnet1 grp ff02::1:ff7d:6604 temp
dev ovirtmgmt port bond0.86 grp ff02::2 temp
After the patch:
dev ovirtmgmt port vnet0 grp ff02::1:ff7d:6603 temp
dev ovirtmgmt port vnet1 grp ff02::1:ff7d:6604 temp
dev ovirtmgmt port bond0.86 grp ff02::fb temp
dev ovirtmgmt port bond0.86 grp ff02::2 temp
dev ovirtmgmt port bond0.86 grp ff02::d temp
dev ovirtmgmt port vnet0 grp ff02::1:ff00:76 temp
dev ovirtmgmt port bond0.86 grp ff02::16 temp
dev ovirtmgmt port vnet1 grp ff02::1:ff00:77 temp
dev ovirtmgmt port bond0.86 grp ff02::1:ff00:def temp
dev ovirtmgmt port bond0.86 grp ff02::1:ffa1:40bf temp
Fixes: 08b202b67264 ("bridge br_multicast: IPv6 MLD support.") Reported-by: Rik Theys <Rik.Theys@esat.kuleuven.be> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@redhat.com> Tested-by: Rik Theys <Rik.Theys@esat.kuleuven.be> Signed-off-by: David S. Miller <davem@davemloft.net>
Nathan Sullivan [Fri, 22 May 2015 14:22:10 +0000 (09:22 -0500)]
net: macb: Disable half duplex gigabit on Zynq
According to the Zynq TRM, gigabit half duplex is not supported. Add a
new cap and compatible string so Zynq can avoid advertising that mode.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nathan Sullivan [Fri, 22 May 2015 14:22:09 +0000 (09:22 -0500)]
net: macb: Document zynq gem dt binding
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubeček [Fri, 22 May 2015 11:40:09 +0000 (13:40 +0200)]
ipv4: fill in table id when replacing a route
When replacing an IPv4 route, tb_id member of the new fib_alias
structure is not set in the replace code path so that the new route is
ignored.
Fixes: 0ddcf43d5d4a ("ipv4: FIB Local/MAIN table collapse") Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Fri, 22 May 2015 11:15:22 +0000 (13:15 +0200)]
cdc_ncm: Fix tx_bytes statistics
The tx_curr_frame_payload field is u32. When we try to calculate a
small negative delta based on it, we end up with a positive integer
close to 2^32 instead. So the tx_bytes pointer increases by about
2^32 for every transmitted frame.
Fix by calculating the delta as a signed long.
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk> Reported-by: Florian Bruhin <me@the-compiler.org> Fixes: 7a1e890e2168 ("usbnet: Fix tx_bytes statistic running backward in cdc_ncm") Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
The following patchset contain Netfilter fixes for your net tree, they are:
1) Fix a race in nfnetlink_log and nfnetlink_queue that can lead to a crash.
This problem is due to wrong order in the per-net registration and netlink
socket events. Patch from Francesco Ruggeri.
2) Make sure that counters that userspace pass us are higher than 0 in all the
x_tables frontends. Discovered via Trinity, patch from Dave Jones.
3) Revert a patch for br_netfilter to rely on the conntrack status bits. This
breaks stateless IPv6 NAT transformations. Patch from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_error does not check if in_dev is NULL before dereferencing it.
IThe following sequence of calls is possible:
CPU A CPU B
ip_rcv_finish
ip_route_input_noref()
ip_route_input_slow()
inetdev_destroy()
dst_input()
With the result that a network device can be destroyed while processing
an input packet.
A crash was triggered with only unicast packets in flight, and
forwarding enabled on the only network device. The error condition
was created by the removal of the network device.
As such it is likely the that error code was -EHOSTUNREACH, and the
action taken by ip_error (if in_dev had been accessible) would have
been to not increment any counters and to have tried and likely failed
to send an icmp error as the network device is going away.
Therefore handle this weird case by just dropping the packet if
!in_dev. It will result in dropping the packet sooner, and will not
result in an actual change of behavior.
Fixes: 251da4130115b ("ipv4: Cache ip_error() routes even when not forwarding.") Reported-by: Vittorio Gambaletta <linuxbugs@vittgam.net> Tested-by: Vittorio Gambaletta <linuxbugs@vittgam.net> Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 22 May 2015 04:51:19 +0000 (21:51 -0700)]
tcp: fix a potential deadlock in tcp_get_info()
Taking socket spinlock in tcp_get_info() can deadlock, as
inet_diag_dump_icsk() holds the &hashinfo->ehash_locks[i],
while packet processing can use the reverse locking order.
We could avoid this locking for TCP_LISTEN states, but lockdep would
certainly get confused as all TCP sockets share same lockdep classes.
[ 523.722504] ======================================================
[ 523.728706] [ INFO: possible circular locking dependency detected ]
[ 523.734990] 4.1.0-dbg-DEV #1676 Not tainted
[ 523.739202] -------------------------------------------------------
[ 523.745474] ss/18032 is trying to acquire lock:
[ 523.750002] (slock-AF_INET){+.-...}, at: [<ffffffff81669d44>] tcp_get_info+0x2c4/0x360
[ 523.758129]
[ 523.758129] but task is already holding lock:
[ 523.763968] (&(&hashinfo->ehash_locks[i])->rlock){+.-...}, at: [<ffffffff816bcb75>] inet_diag_dump_icsk+0x1d5/0x6c0
[ 523.774661]
[ 523.774661] which lock already depends on the new lock.
[ 523.774661]
[ 523.782850]
[ 523.782850] the existing dependency chain (in reverse order) is:
[ 523.790326]
-> #1 (&(&hashinfo->ehash_locks[i])->rlock){+.-...}:
[ 523.796599] [<ffffffff811126bb>] lock_acquire+0xbb/0x270
[ 523.802565] [<ffffffff816f5868>] _raw_spin_lock+0x38/0x50
[ 523.808628] [<ffffffff81665af8>] __inet_hash_nolisten+0x78/0x110
[ 523.815273] [<ffffffff816819db>] tcp_v4_syn_recv_sock+0x24b/0x350
[ 523.822067] [<ffffffff81684d41>] tcp_check_req+0x3c1/0x500
[ 523.828199] [<ffffffff81682d09>] tcp_v4_do_rcv+0x239/0x3d0
[ 523.834331] [<ffffffff816842fe>] tcp_v4_rcv+0xa8e/0xc10
[ 523.840202] [<ffffffff81658fa3>] ip_local_deliver_finish+0x133/0x3e0
[ 523.847214] [<ffffffff81659a9a>] ip_local_deliver+0xaa/0xc0
[ 523.853440] [<ffffffff816593b8>] ip_rcv_finish+0x168/0x5c0
[ 523.859624] [<ffffffff81659db7>] ip_rcv+0x307/0x420
Lets use u64_sync infrastructure instead. As a bonus, 64bit
arches get optimized, as these are nop for them.
Fixes: 0df48c26d841 ("tcp: add tcpi_bytes_acked to tcp_info") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Airlie [Fri, 22 May 2015 03:31:03 +0000 (13:31 +1000)]
Merge tag 'drm-intel-fixes-2015-05-21' of git://anongit.freedesktop.org/drm-intel into drm-fixes
There's a stable backport from Ander [1] that combines this and a few
other commits to fix the flickering on v4.0, reported in [2] among
others. Having this upstream is obviously a requirement for stable.
* tag 'drm-intel-fixes-2015-05-21' of git://anongit.freedesktop.org/drm-intel:
drm/i915: fix screen flickering
crypto: s390/ghash - Fix incorrect ghash icv buffer handling.
Multitheaded tests showed that the icv buffer in the current ghash
implementation is not handled correctly. A move of this working ghash
buffer value to the descriptor context fixed this. Code is tested and
verified with an multithreaded application via af_alg interface.
Cc: stable@vger.kernel.org Signed-off-by: Harald Freudenberger <freude@linux.vnet.ibm.com> Signed-off-by: Gerald Schaefer <geraldsc@linux.vnet.ibm.com> Reported-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Linus Torvalds [Fri, 22 May 2015 02:54:50 +0000 (19:54 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"Bug fixes.
Three for our crypto code, two for eBPF, and one memory management fix
to get machines with memory > 8TB working"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/mm: correct return value of pmd_pfn
s390/crypto: fix stckf loop
s390/zcrypt: Fix invalid domain handling during ap module unload
s390/bpf: Fix gcov stack space problem
s390/zcrypt: fixed ap poll timer behavior
s390/bpf: Adjust ALU64_DIV/MOD to match interpreter change
Linus Torvalds [Fri, 22 May 2015 00:54:00 +0000 (17:54 -0700)]
Merge tag 'sound-4.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This batch became slightly large, just because I've been on vacation
for the last two weeks. Nothing to scare much here, all
device-specific fixes, mostly small patches.
Majority of patches are for HD-audio, especially Dell machines. The
rest are small ASoC fixes for various codecs, and a USB-audio quirk.
One PCM fix is included to ease the faulty condition checks in the
case of two periods PCM buffers"
* tag 'sound-4.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Disable widget power-saving for ALC292 & co
ALSA: hda - Reduce verbs by node power-saves
ALSA: sound/atmel/ac97c.c: remove unused variable
ALSA: usb-audio: Add quirk for MS LifeCam Studio
ALSA: pcm: Modify double acknowledged interrupts check condition
ALSA: hda/realtek - ALC292 dock fix for Thinkpad L450
ALSA: hda - Add Conexant codecs CX20721, CX20722, CX20723 and CX20724
ALSA: hda - Fix headset mic and mic-in for a Dell desktop
ASoC: wm8994: correct BCLK DIV 348 to 384
ASoC: wm8960: fix "RINPUT3" audio route error
ASoC: dapm: Modify widget stream name according to prefix
ALSA: hda - Add headset mic quirk for Dell Inspiron 5548
ASoC: rt5645: Fix mask for setting RT5645_DMIC_2_DP_GPIO12 bit
ASoC: rt5645: Add ACPI match ID
ALSA: hda/realtek - Add ALC298 alias name for Dell
ASoC: uda1380: Avoid accessing i2c bus when codec is disabled
ALSA: hda/realtek - Fix typo for ALC286/ALC288
ASoC: mc13783: Fix wrong mask value used in mc13xxx_reg_rmw() calls
ALSA: hda - Add headphone quirk for Lifebook E752
ASoC: davinci-mcasp: Correct pm status check in suspend callback
Linus Torvalds [Fri, 22 May 2015 00:36:23 +0000 (17:36 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull infiniband/rdma fixes from Doug Ledford:
"This should hopefully be the last request for 4.1-rc for the RDMA
stack. It contains some late ocrdma fixes that I'm including because
they are small and self contained. It also contains two bug fixes
that are simple and easily verified.
Summary:
- a number of small, well contained bug fixes for ocrdma driver
- a simple fix for the connection negotiation sequence on IB
- fix for broken AF_IB address on UD queue pair support"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/cma: Fix broken AF_IB UD support
ib/cm: Change reject message type when destroying cm_id
RDMA/ocrdma: Update ocrdma version number
RDMA/ocrdma: Fail connection for MTU lesser than 512
RDMA/ocrdma: Fix dmac resolution for link local address
RDMA/ocrdma: Prevent allocation of DPP PDs if FW doesnt support it
RDMA/ocrdma: Fix the request length for RDMA_QUERY_QP mailbox command to FW.
RDMA/ocrdma: Use VID 0 if PFC is enabled and vlan is not configured
RDMA/ocrdma: Fix QP state transition in destroy_qp
RDMA/ocrdma: Report EQ full fatal error
RDMA/ocrdma: Fix EQ destroy failure during driver unload
Linus Torvalds [Fri, 22 May 2015 00:23:11 +0000 (17:23 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
"Bugfixes for HID subsystem that should go in 4.1. Important
highlights:
- the patch that extended support for HID++ protocol for TK820
touchpad turns out to be causing regressions due to firmware
issues; patch reverting back to basic support from Benjamin
Tissoires
- Wacom driver can oops for devices that report non-touch data on
touch interfaces. Fix from Ping Cheng
- gpiolib is not mandatory for i2c-hid, so the driver shouldn't fail
if gpiolib is not enabled. Fix from Mika Westerberg"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: wacom: fix an Oops caused by wacom_wac_finger_count_touches
HID: usbhid: Add HID_QUIRK_NOGET for Aten DVI KVM switch
HID: hid-sensor-hub: Fix debug lock warning
Revert "HID: logitech-hidpp: support combo keyboard touchpad TK820"
HID: i2c-hid: Do not fail probing if gpiolib is not enabled
Marek Vasut [Fri, 8 May 2015 05:25:49 +0000 (22:25 -0700)]
Input: smtpe-ts - wait 50mS until polling for pen-up
Wait a little bit longer, 50mS instead of 20mS, until the driver starts
polling for pen-up. The problematic behavior before this patch is applied
is as follows. The behavior was observed on the STMPE610QTR controller.
Upon a physical pen-down event, the touchscreen reports one set of x-y-p
coordinates and a pen-down event. After that, the pen-up polling is
triggered and since the controller is not ready yet, the polling mistakenly
detects a pen-up event while the physical state is still such that the pen
is down on the touch surface.
The pen-up handling flushes the controller FIFO, so after that, all the
samples in the controller are discarded. The controller becomes ready
shortly after this bogus pen-up handling and does generate again a pen-down
interrupt. This time, the controller contains x-y-p samples which all read
as zero. Since pressure value is zero, this set of samples is effectively
ignored by userland.
In the end, the driver just bounces between pen-down and bogus pen-up
handling, generating no useful results. Fix this by giving the controller a
bit more time before polling it for pen-up.
Marek Vasut [Fri, 8 May 2015 05:24:58 +0000 (22:24 -0700)]
Input: smtpe-ts - use msecs_to_jiffies() instead of HZ
Use msecs_to_jiffies(20) instead of plain (HZ / 50), as the former is much
more explicit about it's behavior. We want to schedule the task 20 mS from
now, so make it explicit in the code.
Linus Torvalds [Thu, 21 May 2015 23:57:50 +0000 (16:57 -0700)]
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Michael Turquette:
"The first set of clk fixes for 4.1 are all driver bugs, with the
exception of a single locking fix in the core code.
All driver fixes are for code that was merged recently. The Samsung
stuff is mostly fixes around suspend/resume, the Qualcomm fixes are
for invalid hardware configuration data and the Silicon Labs patches
are fixes following their move away from platform_data to Device Tree"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: si5351: Do not pass struct clk in platform_data
clk: si5351: Mention clock-names in the binding documentation
clk: add missing lock when call clk_core_enable in clk_set_parent
clk: exynos5420: Restore GATE_BUS_TOP on suspend
clk: qcom: Fix MSM8916 gfx3d_clk_src configuration
clk: qcom: Fix MSM8916 venus divider value
clk: exynos5433: Fix wrong PMS value of exynos5433_pll_rates
clk: exynos5433: Fix wrong parent clock of sclk_apollo clock
clk: exynos5433: Fix CLK_PCLK_MONOTONIC_CNT clk register assignment
clk: exynos5433: Fix wrong offset of PCLK_MSCL_SECURE_SMMU_JPEG
clk: Use CONFIG_ARCH_EXYNOS instead of CONFIG_ARCH_EXYNOS5433
Thomas Hellstrom [Wed, 20 May 2015 21:50:30 +0000 (14:50 -0700)]
Input: joydev - don't classify the vmmouse as a joystick
Joydev is currently thinking some absolute mice are joystick, and that
messes up games in VMware guests, as the cursor typically gets stuck in
the top left corner.
Try to detect the event signature of a VMmouse input device and back off
for such devices. We're still incorrectly detecting, for example, the
VMware absolute USB mouse as a joystick, but adding an event signature
matching also that device would be considerably more risky, so defer that
to a later merge window.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Daniel Borkmann [Wed, 20 May 2015 15:13:33 +0000 (17:13 +0200)]
net: sched: fix call_rcu() race on classifier module unloads
Vijay reported that a loop as simple as ...
while true; do
tc qdisc add dev foo root handle 1: prio
tc filter add dev foo parent 1: u32 match u32 0 0 flowid 1
tc qdisc del dev foo root
rmmod cls_u32
done
... will panic the kernel. Moreover, he bisected the change
apparently introducing it to 78fd1d0ab072 ("netlink: Re-add
locking to netlink_lookup() and seq walker").
The removal of synchronize_net() from the netlink socket
triggering the qdisc to be removed, seems to have uncovered
an RCU resp. module reference count race from the tc API.
Given that RCU conversion was done after e341694e3eb5 ("netlink:
Convert netlink_lookup() to use RCU protected hash table")
which added the synchronize_net() originally, occasion of
hitting the bug was less likely (not impossible though):
When qdiscs that i) support attaching classifiers and,
ii) have at least one of them attached, get deleted, they
invoke tcf_destroy_chain(), and thus call into ->destroy()
handler from a classifier module.
After RCU conversion, all classifier that have an internal
prio list, unlink them and initiate freeing via call_rcu()
deferral.
Meanhile, tcf_destroy() releases already reference to the
tp->ops->owner module before the queued RCU callback handler
has been invoked.
Subsequent rmmod on the classifier module is then not prevented
since all module references are already dropped.
By the time, the kernel invokes the RCU callback handler from
the module, that function address is then invalid.
One way to fix it would be to add an rcu_barrier() to
unregister_tcf_proto_ops() to wait for all pending call_rcu()s
to complete.
synchronize_rcu() is not appropriate as under heavy RCU
callback load, registered call_rcu()s could be deferred
longer than a grace period. In case we don't have any pending
call_rcu()s, the barrier is allowed to return immediately.
Since we came here via unregister_tcf_proto_ops(), there
are no users of a given classifier anymore. Further nested
call_rcu()s pointing into the module space are not being
done anywhere.
Only cls_bpf_delete_prog() may schedule a work item, to
unlock pages eventually, but that is not in the range/context
of cls_bpf anymore.
Fixes: 25d8c0d55f24 ("net: rcu-ify tcf_proto") Fixes: 9888faefe132 ("net: sched: cls_basic use RCU") Reported-by: Vijay Subramanian <subramanian.vijay@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Cc: John Fastabend <john.r.fastabend@intel.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Thomas Graf <tgraf@suug.ch> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Alexei Starovoitov <ast@plumgrid.com> Tested-by: Vijay Subramanian <subramanian.vijay@gmail.com> Acked-by: Alexei Starovoitov <ast@plumgrid.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Work [Tue, 19 May 2015 06:26:23 +0000 (23:26 -0700)]
md/raid0: fix restore to sector variable in raid0_make_request
The variable "sector" in "raid0_make_request()" was improperly updated
by a call to "sector_div()" which modifies its first argument in place.
Commit 47d68979cc968535cb87f3e5f2e6a3533ea48fbd restored this variable
after the call for later re-use. Unfortunetly the restore was done after
the referenced variable "bio" was advanced. This lead to the original
value and the restored value being different. Here we move this line to
the proper place.
One observed side effect of this bug was discarding a file though
unlinking would cause an unrelated file's contents to be discarded.
Signed-off-by: NeilBrown <neilb@suse.de> Fixes: 47d68979cc96 ("md/raid0: fix bug with chunksize not a power of 2.") Cc: stable@vger.kernel.org (any that received above backport)
URL: https://bugzilla.kernel.org/show_bug.cgi?id=98501
Shaohua Li [Wed, 13 May 2015 16:30:08 +0000 (09:30 -0700)]
raid5: fix broken async operation chain
ops_run_reconstruct6() doesn't correctly chain asyn operations. The tx returned
by async_gen_syndrome should be added as the dependent tx of next stripe.
Hans de Goede [Wed, 20 May 2015 21:37:41 +0000 (14:37 -0700)]
Input: alps - fix finger jumps on lifting 2 fingers on v7 touchpad
On v7 touchpads sometimes when 2 fingers are moved down on the touchpad
until they "fall of" the touchpad, the second touch will report 0 for y
(max y really since the y axis is inverted) and max x as coordinates,
rather then reporting 0, 0 as is expected for a non touching finger.
This commit detects this and treats these touches as non touching.
See the evemu-recording here:
https://bugzilla.redhat.com/attachment.cgi?id=1025058
Matthew Finlay [Tue, 19 May 2015 07:11:48 +0000 (00:11 -0700)]
IB/cma: Fix broken AF_IB UD support
Support for using UD and AF_IB is currently broken. The
IB_CM_SIDR_REQ_RECEIVED message is not handled properly in
cma_save_net_info() and we end up falling into code that will try and
process the request as ipv4/ipv6, which will end up failing.
The resolution is to add a check for the SIDR_REQ and call
cma_save_ib_info() with a NULL path record. Change cma_save_ib_info()
to copy the src sib info from the listen_id when the path record is NULL.
Reported-by: Hari Shankar <Hari.Shankar@netapp.com> Signed-off-by: Matt Finlay <matt@mellanox.com> Acked-by: Sean Hefty <sean.hefty@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Minghuan Lian [Wed, 20 May 2015 15:13:15 +0000 (10:13 -0500)]
irqchip/gicv3-its: ITS table size should not be smaller than PSZ
When allocating a device table, if the requested allocation is smaller
than the default granule size of the ITS then, we need to round up to
the default size.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
[ stuart: Added comments and massaged changelog ] Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com> Reviewed-by: Marc Zygnier <marc.zyngier@arm.com> Cc: <linux-arm-kernel@lists.infradead.org> Cc: <jason@lakedaemon.net> Link: http://lkml.kernel.org/r/1432134795-661-1-git-send-email-stuart.yoder@freescale.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Chris Mason [Wed, 20 May 2015 01:54:41 +0000 (18:54 -0700)]
Btrfs: fix regression in raid level conversion
Commit 2f0810880f082fa8ba66ab2c33b02e4ff9770a5e changed
btrfs_set_block_group_ro to avoid trying to allocate new chunks with the
new raid profile during conversion. This fixed failures when there was
no space on the drive to allocate a new chunk, but the metadata
reserves were sufficient to continue the conversion.
But this ended up causing a regression when the drive had plenty of
space to allocate new chunks, mostly because reduce_alloc_profile isn't
using the new raid profile.
Fixing btrfs_reduce_alloc_profile is a bigger patch. For now, do a
partial revert of 2f0810880, and don't error out if we hit ENOSPC.
Signed-off-by: Chris Mason <clm@fb.com> Tested-by: Dave Sterba <dsterba@suse.cz> Reported-by: Holger Hoffstaette <holger.hoffstaette@googlemail.com>
.. which introduced a regression that prevented all lingering requests
requeued in kick_requests() from ever being sent to the OSDs, resulting
in a lot of missed notifies. In retrospect it's pretty obvious that
r_req_lru_item item in the case of lingering requests can be used not
only for notarget, but also for unsent linkage due to how tightly
actual map and enqueue operations are coupled in __map_request().
The assertion that was being silenced is taken care of in the previous
("libceph: request a new osdmap if lingering request maps to no osd")
commit: by always kicking homeless lingering requests we ensure that
none of them ends up on the notarget list outside of the critical
section guarded by request_mutex.
Cc: stable@vger.kernel.org # 3.18+, needs b0494532214b "libceph: request a new osdmap if lingering request maps to no osd" Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Reviewed-by: Sage Weil <sage@redhat.com>
Ilya Dryomov [Mon, 11 May 2015 14:53:10 +0000 (17:53 +0300)]
libceph: request a new osdmap if lingering request maps to no osd
This commit does two things. First, if there are any homeless
lingering requests, we now request a new osdmap even if the osdmap that
is being processed brought no changes, i.e. if a given lingering
request turned homeless in one of the previous epochs and remained
homeless in the current epoch. Not doing so leaves us with a stale
osdmap and as a result we may miss our window for reestablishing the
watch and lose notifies.
MON=1 OSD=1:
# cat linger-needmap.sh
#!/bin/bash
rbd create --size 1 test
DEV=$(rbd map test)
ceph osd out 0
rbd map dne/dne # obtain a new osdmap as a side effect (!)
sleep 1
ceph osd in 0
rbd resize --size 2 test
# rbd info test | grep size -> 2M
# blockdev --getsize $DEV -> 1M
N.B.: Not obtaining a new osdmap in between "osd out" and "osd in"
above is enough to make it miss that resize notify, but that is a
bug^Wlimitation of ceph watch/notify v1.
Second, homeless lingering requests are now kicked just like those
lingering requests whose mapping has changed. This is mainly to
recognize that a homeless lingering request makes no sense and to
preserve the invariant that a registered lingering request is not
sitting on any of r_req_lru_item lists. This spares us a WARN_ON,
which commit ba9d114ec557 ("libceph: clear r_req_lru_item in
__unregister_linger_request()") tried to fix the _wrong_ way.
Ted Kim [Thu, 14 May 2015 19:49:01 +0000 (12:49 -0700)]
ib/cm: Change reject message type when destroying cm_id
Problem reported by: Ted Kim <ted.h.kim@oracle.com>:
We have a case where a Linux system and a non-Linux system are
trying to interoperate. The Linux host is the active side and
starts the connection establishment, but later decides to not go
through with the connection setup and does rdma_destroy_id().
The rdma_destroy_id() eventually works its way down to cm_destroy_id()
in core/cm.c, where a REJ is sent. The non-Linux system
has some trouble recognizing the REJ because of:
A. CM states which can't receive the REJ
B. Some issues about REJ formatting (missing comm ID)
ISSUE A: That part of the spec says, a Consumer Reject REJ can be
sent for a connection abort, but it goes further
and says: can send a REJ message with a "Consumer Reject"
Reason code if they are in a CM state (i.e. REP
Rcvd, MRA(REP) Sent, REQ Rcvd, MRA Sent) that allows
a REJ to be sent (lines 35-38).
Of the states listed there in that sentence, it would
seem to limit the active side to using the Consumer Reject
(for the abort case) in just the REP-Rcvd and MRA-REP-Sent
states. That is basically only after the active side
sees a REP (or alternatively goes down the state transitions
to timeout in which case a Timeout REJ is sent).
As a fix, in cm-destroy-id() move the IB-CM-MRA-REQ-RCVD case
to the same as REQ-SENT. Essentially, make a REJ sent after
getting an MRA on active side a timeout rather than Consumer-
Reject, which is arguably more correct with the CM state
diagrams previous to getting a REP.
Signed-off-by: Ted Kim <ted.h.kim@oracle.com> Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Tim Beale [Mon, 18 May 2015 03:38:38 +0000 (15:38 +1200)]
net: phy: Make sure phy_start() always re-enables the phy interrupts
This is an alternative way of fixing:
commit db9683fb412d ("net: phy: Make sure PHY_RESUMING state change
is always processed")
When the PHY state transitions from PHY_HALTED to PHY_RESUMING, there are
two things we need to do:
1). Re-enable interrupts (and power up the physical link, if powered down)
2). Update the PHY state and net-device based on the link status.
There's no strict reason why #1 has to be done from within the main
phy_state_machine() function. There is a risk that other changes to the
PHY (e.g. setting speed/duplex, which calls phy_start_aneg()) could cause
a subsequent state transition before phy_state_machine() has processed
the PHY_RESUMING state change. This would leave the PHY with interrupts
disabled and/or still in the BMCR_PDOWN/low-power mode.
Moving enabling the interrupts and phy_resume() into phy_start() will
guarantee this work always gets done. As the PHY is already in the HALTED
state and interrupts are disabled, it shouldn't conflict with any work
being done in phy_state_machine(). The downside of this change is that if
the PHY_RESUMING state is ever entered from anywhere else, it'll also have
to repeat this work.
Signed-off-by: Tim Beale <tim.beale@alliedtelesis.co.nz> Signed-off-by: David S. Miller <davem@davemloft.net>
(1) When adding a nexthop of a multipath route fails (e.g. because of a
conflict with an existing route), we are supposed to delete nexthops
already added. However, currently we try to also delete all nexthops we
haven't even tried to add yet so that a "ip route add" command can
actually remove pre-existing routes if it fails.
(2) Attempt to replace a multipath route results in a broken siblings
linked list. Following commands (like "ip route del") can then either
follow a link into freed memory or end in an infinite loop (if the slab
object has been reused).
v2: fix an omission in first patch
v3: change the semantics of replace operation to better match IPv4
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubeček [Mon, 18 May 2015 18:54:00 +0000 (20:54 +0200)]
ipv6: fix ECMP route replacement
When replacing an IPv6 multipath route with "ip route replace", i.e.
NLM_F_CREATE | NLM_F_REPLACE, fib6_add_rt2node() replaces only first
matching route without fixing its siblings, resulting in corrupted
siblings linked list; removing one of the siblings can then end in an
infinite loop.
IPv6 ECMP implementation is a bit different from IPv4 so that route
replacement cannot work in exactly the same way. This should be a
reasonable approximation:
1. If the new route is ECMP-able and there is a matching ECMP-able one
already, replace it and all its siblings (if any).
2. If the new route is ECMP-able and no matching ECMP-able route exists,
replace first matching non-ECMP-able (if any) or just add the new one.
3. If the new route is not ECMP-able, replace first matching
non-ECMP-able route (if any) or add the new route.
We also need to remove the NLM_F_REPLACE flag after replacing old
route(s) by first nexthop of an ECMP route so that each subsequent
nexthop does not replace previous one.
Fixes: 51ebd3181572 ("ipv6: add support of equal cost multipath (ECMP)") Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubeček [Mon, 18 May 2015 18:53:55 +0000 (20:53 +0200)]
ipv6: do not delete previously existing ECMP routes if add fails
If adding a nexthop of an IPv6 multipath route fails, comment in
ip6_route_multipath() says we are going to delete all nexthops already
added. However, current implementation deletes even the routes it
hasn't even tried to add yet. For example, running
ip route add 1234:5678::/64 \
nexthop via fe80::aa dev dummy1 \
nexthop via fe80::bb dev dummy1 \
nexthop via fe80::cc dev dummy1
twice results in removing all routes first command added.
Limit the second (delete) run to nexthops that succeeded in the first
(add) run.
Fixes: 51ebd3181572 ("ipv6: add support of equal cost multipath (ECMP)") Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter: nfnetlink_{log,queue}: Register pernet in first place
nfnetlink_{log,queue}_init() register the netlink callback nf*_rcv_nl_event
before registering the pernet_subsys, but the callback relies on data
structures allocated by pernet init functions.
When nfnetlink_{log,queue} is loaded, if a netlink message is received after
the netlink callback is registered but before the pernet_subsys is registered,
the kernel will panic in the sequence
nfulnl_rcv_nl_event
nfnl_log_pernet
net_generic
BUG_ON(id == 0) where id is nfnl_log_net_id.
The panic can be easily reproduced in 4.0.3 by:
while true ;do modprobe nfnetlink_log ; rmmod nfnetlink_log ; done &
while true ;do ip netns add dummy ; ip netns del dummy ; done &
This patch moves register_pernet_subsys to earlier in nfnetlink_log_init.
Notice that the BUG_ON hit in 4.0.3 was recently removed in 2591ffd308
["netns: remove BUG_ONs from net_generic()"].
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
projects / linux-beck.git / log