Mohammed Gamal [Mon, 31 May 2010 19:40:54 +0000 (22:40 +0300)]
KVM: VMX: Properly return error to userspace on vmentry failure
The vmexit handler returns KVM_EXIT_UNKNOWN since there is no handler
for vmentry failures. This intercepts vmentry failures and returns
KVM_FAIL_ENTRY to userspace instead.
Signed-off-by: Mohammed Gamal <m.gamal005@gmail.com> Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Zachary Amsden [Thu, 27 May 2010 01:09:43 +0000 (15:09 -1000)]
KVM: SVM: Fix EFER.LME being stripped
Must set VCPU register to be the guest notion of EFER even if that
setting is not valid on hardware. This was masked by the set in
set_efer until 7657fd5ace88e8092f5f3a84117e093d7b893f26 broke that.
Fix is simply to set the VCPU register before stripping bits.
Signed-off-by: Zachary Amsden <zamsden@redhat.com> Signed-off-by: Avi Kivity <avi@redhat.com>
Lai Jiangshan [Wed, 26 May 2010 08:48:19 +0000 (16:48 +0800)]
KVM: MMU: calculate correct gfn for small host pages backing large guest pages
In Documentation/kvm/mmu.txt:
gfn:
Either the guest page table containing the translations shadowed by this
page, or the base page frame for linear translations. See role.direct.
But in function FNAME(fetch)(), sp->gfn is incorrect when one of following
situations occurred:
1) guest is 32bit paging and the guest PDE maps a 4-MByte page
(backed by 4k host pages), FNAME(fetch)() miss handling the quadrant.
And if guest use pse-36, "table_gfn = gpte_to_gfn(gw->ptes[level - delta]);"
is incorrect.
2) guest is long mode paging and the guest PDPTE maps a 1-GByte page
(backed by 4k or 2M host pages).
So we fix it to suit to the document and suit to the code which
requires sp->gfn correct when sp->role.direct=1.
We use the goal mapping gfn(gw->gfn) to calculate the base page frame
for linear translations, it is simple and easy to be understood.
Reported-by: Marcelo Tosatti <mtosatti@redhat.com> Reported-by: Gui Jianfeng <guijianfeng@cn.fujitsu.com> Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com> Signed-off-by: Avi Kivity <avi@redhat.com>
Lai Jiangshan [Wed, 26 May 2010 08:48:25 +0000 (16:48 +0800)]
KVM: MMU: Calculate correct base gfn for direct non-DIR level
In Document/kvm/mmu.txt:
gfn:
Either the guest page table containing the translations shadowed by this
page, or the base page frame for linear translations. See role.direct.
But in __direct_map(), the base gfn calculation is incorrect,
it does not calculate correctly when level=3 or 4.
Fix by using PT64_LVL_ADDR_MASK() which accounts for all levels correctly.
Reported-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com> Signed-off-by: Avi Kivity <avi@redhat.com>
Lai Jiangshan [Wed, 26 May 2010 08:49:59 +0000 (16:49 +0800)]
KVM: MMU: Don't allocate gfns page for direct mmu pages
When sp->role.direct is set, sp->gfns does not contain any essential
information, leaf sptes reachable from this sp are for a continuous
guest physical memory range (a linear range).
So sp->gfns[i] (if it was set) equals to sp->gfn + i. (PT_PAGE_TABLE_LEVEL)
Obviously, it is not essential information, we can calculate it when need.
It means we don't need sp->gfns when sp->role.direct=1,
Thus we can save one page usage for every kvm_mmu_page.
Note:
Access to sp->gfns must be wrapped by kvm_mmu_page_get_gfn()
or kvm_mmu_page_set_gfn().
It is only exposed in FNAME(sync_page).
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com> Signed-off-by: Avi Kivity <avi@redhat.com>
Xiao Guangrong [Mon, 24 May 2010 07:41:33 +0000 (15:41 +0800)]
KVM: MMU: allow more page become unsync at getting sp time
Allow more page become asynchronous at getting sp time, if need create new
shadow page for gfn but it not allow unsync(level > 1), we should unsync all
gfn's unsync page
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com> Signed-off-by: Avi Kivity <avi@redhat.com>
Xiao Guangrong [Mon, 24 May 2010 07:40:07 +0000 (15:40 +0800)]
KVM: MMU: allow more page become unsync at gfn mapping time
In current code, shadow page can become asynchronous only if one
shadow page for a gfn, this rule is too strict, in fact, we can
let all last mapping page(i.e, it's the pte page) become unsync,
and sync them at invlpg or flush tlb time.
This patch allow more page become asynchronous at gfn mapping time
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com> Signed-off-by: Avi Kivity <avi@redhat.com>
Xiao Guangrong [Sat, 15 May 2010 10:52:34 +0000 (18:52 +0800)]
KVM: MMU: don't write-protect if have new mapping to unsync page
Two cases maybe happen in kvm_mmu_get_page() function:
- one case is, the goal sp is already in cache, if the sp is unsync,
we only need update it to assure this mapping is valid, but not
mark it sync and not write-protect sp->gfn since it not broke unsync
rule(one shadow page for a gfn)
- another case is, the goal sp not existed, we need create a new sp
for gfn, i.e, gfn (may)has another shadow page, to keep unsync rule,
we should sync(mark sync and write-protect) gfn's unsync shadow page.
After enabling multiple unsync shadows, we sync those shadow pages
only when the new sp not allow to become unsync(also for the unsyc
rule, the new rule is: allow all pte page become unsync)
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com> Signed-off-by: Avi Kivity <avi@redhat.com>
Alex Williamson [Wed, 12 May 2010 13:46:31 +0000 (09:46 -0400)]
KVM: remove CAP_SYS_RAWIO requirement from kvm_vm_ioctl_assign_irq
Remove this check in an effort to allow kvm guests to run without
root privileges. This capability check doesn't seem to add any
security since the device needs to have already been added via the
assign device ioctl and the io actually occurs through the pci
sysfs interface.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Dongxiao Xu [Tue, 11 May 2010 10:29:45 +0000 (18:29 +0800)]
KVM: VMX: VMCLEAR/VMPTRLD usage changes
Originally VMCLEAR/VMPTRLD is called on vcpu migration. To
support hosted VMM coexistance, VMCLEAR is executed on vcpu
schedule out, and VMPTRLD is executed on vcpu schedule in.
This could also eliminate the IPI when doing VMCLEAR.
Avi Kivity [Mon, 10 May 2010 09:09:56 +0000 (12:09 +0300)]
KVM: MMU: Fix free memory accounting race in mmu_alloc_roots()
We drop the mmu lock between freeing memory and allocating the roots; this
allows some other vcpu to sneak in and allocate memory.
While the race is benign (resulting only in temporary overallocation, not oom)
it is simple and easy to fix by moving the freeing close to the allocation.
Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Gleb Natapov [Mon, 10 May 2010 08:16:56 +0000 (11:16 +0300)]
KVM: inject #UD if instruction emulation fails and exit to userspace
Do not kill VM when instruction emulation fails. Inject #UD and report
failure to userspace instead. Userspace may choose to reenter guest if
vcpu is in userspace (cpl == 3) in which case guest OS will kill
offending process and continue running.
Gui Jianfeng [Wed, 5 May 2010 01:03:49 +0000 (09:03 +0800)]
KVM: MMU: make kvm_mmu_zap_page() return the number of pages it actually freed
Currently, kvm_mmu_zap_page() returning the number of freed children sp.
This might confuse the caller, because caller don't know the actual freed
number. Let's make kvm_mmu_zap_page() return the number of pages it actually
freed.
Signed-off-by: Gui Jianfeng <guijianfeng@cn.fujitsu.com> Signed-off-by: Avi Kivity <avi@redhat.com>
Joerg Roedel [Wed, 5 May 2010 14:04:44 +0000 (16:04 +0200)]
KVM: SVM: Allow EFER.LMSLE to be set with nested svm
This patch enables setting of efer bit 13 which is allowed
in all SVM capable processors. This is necessary for the
SLES11 version of Xen 4.0 to boot with nested svm.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Avi Kivity <avi@redhat.com>
Avi Kivity [Mon, 3 May 2010 13:54:48 +0000 (16:54 +0300)]
KVM: Get rid of KVM_REQ_KICK
KVM_REQ_KICK poisons vcpu->requests by having a bit set during normal
operation. This causes the fast path check for a clear vcpu->requests
to fail all the time, triggering tons of atomic operations.
Fix by replacing KVM_REQ_KICK with a vcpu->guest_mode atomic.
KVM: x86 emulator: x86_emulate_insn() return -1 only in case of emulation failure
Currently emulator returns -1 when emulation failed or IO is needed.
Caller tries to guess whether emulation failed by looking at other
variables. Make it easier for caller to recognise error condition by
always returning -1 in case of failure. For this new emulator
internal return value X86EMUL_IO_NEEDED is introduced. It is used to
distinguish between error condition (which returns X86EMUL_UNHANDLEABLE)
and condition that requires IO exit to userspace to continue emulation.
Signed-off-by: Gleb Natapov <gleb@redhat.com> Signed-off-by: Avi Kivity <avi@redhat.com>
KVM: fill in run->mmio details in (read|write)_emulated function
Fill in run->mmio details in (read|write)_emulated function just like
pio does. There is no point in filling only vcpu fields there just to
copy them into vcpu->run a little bit later.
Signed-off-by: Gleb Natapov <gleb@redhat.com> Signed-off-by: Avi Kivity <avi@redhat.com>
KVM: x86 emulator: fix X86EMUL_RETRY_INSTR and X86EMUL_CMPXCHG_FAILED values
Currently X86EMUL_PROPAGATE_FAULT, X86EMUL_RETRY_INSTR and
X86EMUL_CMPXCHG_FAILED have the same value so caller cannot
distinguish why function such as emulator_cmpxchg_emulated()
(which can return both X86EMUL_PROPAGATE_FAULT and
X86EMUL_CMPXCHG_FAILED) failed.
Signed-off-by: Gleb Natapov <gleb@redhat.com> Signed-off-by: Avi Kivity <avi@redhat.com>
KVM: x86 emulator: add get_cached_segment_base() callback to x86_emulate_ops
On VMX it is expensive to call get_cached_descriptor() just to get segment
base since multiple vmcs_reads are done instead of only one. Introduce
new call back get_cached_segment_base() for efficiency.
Signed-off-by: Gleb Natapov <gleb@redhat.com> Signed-off-by: Avi Kivity <avi@redhat.com>
KVM: x86 emulator: handle "far address" source operand
ljmp/lcall instruction operand contains address and segment.
It can be 10 bytes long. Currently we decode it as two different
operands. Fix it by introducing new kind of operand that can hold
entire far address.
Signed-off-by: Gleb Natapov <gleb@redhat.com> Signed-off-by: Avi Kivity <avi@redhat.com>
Introduce read cache which is needed for instruction that require more
then one exit to userspace. After returning from userspace the instruction
will be re-executed with cached read value.
Signed-off-by: Gleb Natapov <gleb@redhat.com> Signed-off-by: Avi Kivity <avi@redhat.com>
Avi Kivity [Mon, 3 May 2010 13:05:44 +0000 (16:05 +0300)]
KVM: VMX: Avoid writing HOST_CR0 every entry
cr0.ts may change between entries, so we copy cr0 to HOST_CR0 before each
entry. That is slow, so instead, set HOST_CR0 to have TS set unconditionally
(which is a safe value), and issue a clts() just before exiting vcpu context
if the task indeed owns the fpu.
KVM: x86: avoid unnecessary bitmap allocation when memslot is clean
Although we always allocate a new dirty bitmap in x86's get_dirty_log(),
it is only used as a zero-source of copy_to_user() and freed right after
that when memslot is clean. This patch uses clear_user() instead of doing
this unnecessary zero-source allocation.
Performance improvement: as we can expect easily, the time needed to
allocate a bitmap is completely reduced. In my test, the improved ioctl
was about 4 to 10 times faster than the original one for clean slots.
Furthermore, reducing memory allocations and copies will produce good
effects to caches too.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp> Signed-off-by: Avi Kivity <avi@redhat.com>
Huang Ying [Mon, 31 May 2010 06:28:19 +0000 (14:28 +0800)]
KVM: Avoid killing userspace through guest SRAO MCE on unmapped pages
In common cases, guest SRAO MCE will cause corresponding poisoned page
be un-mapped and SIGBUS be sent to QEMU-KVM, then QEMU-KVM will relay
the MCE to guest OS.
But it is reported that if the poisoned page is accessed in guest
after unmapping and before MCE is relayed to guest OS, userspace will
be killed.
The reason is as follows. Because poisoned page has been un-mapped,
guest access will cause guest exit and kvm_mmu_page_fault will be
called. kvm_mmu_page_fault can not get the poisoned page for fault
address, so kernel and user space MMIO processing is tried in turn. In
user MMIO processing, poisoned page is accessed again, then userspace
is killed by force_sig_info.
To fix the bug, kvm_mmu_page_fault send HWPOISON signal to QEMU-KVM
and do not try kernel and user space MMIO processing for poisoned
page.
[xiao: fix warning introduced by avi]
Reported-by: Max Asbock <masbock@linux.vnet.ibm.com> Signed-off-by: Huang Ying <ying.huang@intel.com> Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com> Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Avi Kivity <avi@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] ibmvscsi: Fix oops when an interrupt is pending during probe
[SCSI] zfcp: Update status read mempool
[SCSI] zfcp: Do not wait for SBALs on stopped queue
[SCSI] zfcp: Fix check whether unchained ct_els is possible
[SCSI] ipr: fix resource path display and formatting
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
davinci: da850/omap-l138 evm: account for DEFDCDC{2,3} being tied high
regulator: tps6507x: allow driver to use DEFDCDC{2,3}_HIGH register
wm8350-regulator: fix wm8350_register_regulator error handling
ab3100: fix off-by-one value range checking for voltage selector
Andre Osterhues [Tue, 13 Jul 2010 20:59:17 +0000 (15:59 -0500)]
ecryptfs: Bugfix for error related to ecryptfs_hash_buckets
The function ecryptfs_uid_hash wrongly assumes that the
second parameter to hash_long() is the number of hash
buckets instead of the number of hash bits.
This patch fixes that and renames the variable
ecryptfs_hash_buckets to ecryptfs_hash_bits to make it
clearer.
Jason Wessel [Thu, 29 Jul 2010 00:10:30 +0000 (19:10 -0500)]
x86,kgdb: Fix hw breakpoint regression
HW breakpoints events stopped working correctly with kgdb
as a result of commit: 018cbffe6819f6f8db20a0a3acd9bab9bfd667e4
(Merge commit 'v2.6.33' into perf/core).
The regression occurred because the behavior changed for setting
NOTIFY_STOP as the return value to the die notifier if the breakpoint
was known to the HW breakpoint API. Because kgdb is using the HW
breakpoint API to register HW breakpoints slots, it must also now
implement the overflow_handler call back else kgdb does not get to see
the events from the die notifier.
The kgdb_ll_trap function will be changed to be general purpose code
which can allow an easy way to implement the hw_breakpoint API
overflow call back.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Acked-by: Dongdong Deng <dongdong.deng@windriver.com> Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
If we don't need a huge amount of memory in ->readdir() then
we can use kmalloc rather than vmalloc to allocate it. This
should cut down on the greater overheads associated with
vmalloc for smaller directories.
We may be able to eliminate vmalloc entirely at some stage,
but this is easy to do right away.
Also using GFP_NOFS to avoid any issues wrt to deleting inodes
while under a glock, and suggestion from Linus to factor out
the alloc/dealloc.
I've given this a test with a variety of different sized
directories and it seems to work ok.
Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Nick Piggin <npiggin@suse.de> Cc: Prarit Bhargava <prarit@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sekhar Nori [Mon, 12 Jul 2010 12:26:21 +0000 (17:56 +0530)]
davinci: da850/omap-l138 evm: account for DEFDCDC{2,3} being tied high
Per the da850/omap-l138 Beta EVM SOM schematic, the DEFDCDC2 and DEFDCDC3 lines are tied high. This leads to a 3.3V IO and 1.2V CVDD
voltage.
Pass the right platform data to the TPS6507x driver so it can operate
on the DEFDCDC{2,3}_HIGH register to read and change voltage levels.
Signed-off-by: Sekhar Nori <nsekhar@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
regulator: tps6507x: allow driver to use DEFDCDC{2,3}_HIGH register
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In TPS6507x, depending on the status of DEFDCDC{2,3} pin either DEFDCDC{2,3}_LOW or DEFDCDC{2,3}_HIGH register needs to be read or
programmed to change the output voltage.
The current driver assumes DEFDCDC{2,3} pins are always tied low
and thus operates only on DEFDCDC{2,3}_LOW register. This need
not always be the case (as is found on OMAP-L138 EVM).
Unfortunately, software cannot read the status of DEFDCDC{2,3} pins.
So, this information is passed through platform data depending on
how the board is wired.
The MPC85xx EDAC driver is missing module device aliases, so the driver
won't load automatically on boot. This patch fixes the issue by adding
proper MODULE_DEVICE_TABLE() macros.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com> Cc: Doug Thompson <dougthompson@xmission.com> Cc: Peter Tyser <ptyser@xes-inc.com> Cc: Dave Jiang <djiang@mvista.com> Cc: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / linux-beck.git / log