Dave P Martin [Fri, 24 Jul 2015 15:37:43 +0000 (16:37 +0100)]
arm64/debug: Eliminate magic number from ESR template definition
<asm/esr.h> has perfectly good constants for defining ESR values
already. Let's use them.
Signed-off-by: Dave Martin <Dave.Martin@arm.com> Acked-by: Mark Rutland <mark.rutland@arm.com> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Dave P Martin [Fri, 24 Jul 2015 15:37:42 +0000 (16:37 +0100)]
arm64/debug: Mask off all reserved bits from generated ESR values
There are only 16 comment bits in a BRK instruction, which
correspond to ESR bits 15:0. Bits 24:16 of the ESR are RES0,
and might have weird meanings in the future.
This code inserts 16 bits of comment in the ESR value instead of
20 (almost certainly a typo in the original code).
Signed-off-by: Dave Martin <Dave.Martin@arm.com> Acked-by: Mark Rutland <mark.rutland@arm.com> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Dave P Martin [Fri, 24 Jul 2015 15:37:41 +0000 (16:37 +0100)]
arm64/debug: Eliminate magic number for size of BRK instruction
The size of an A64 BRK instruction is the same as the size of all other
A64 instructions, because all A64 instructions are the same size.
BREAK_INSTR_SIZE is retained for readibility, but it should not be
an independent constant from AARCH64_INSN_SIZE.
Signed-off-by: Dave Martin <Dave.Martin@arm.com> Acked-by: Mark Rutland <mark.rutland@arm.com> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
arm64: efi: prefer AllocatePages() over efi_low_alloc() for vmlinux
When allocating memory for the kernel image, try the AllocatePages()
boot service to obtain memory at the preferred offset of
'dram_base + TEXT_OFFSET', and only revert to efi_low_alloc() if that
fails. This is the only way to allocate at the base of DRAM if DRAM
starts at 0x0, since efi_low_alloc() refuses to allocate at 0x0.
Tested-by: Haojian Zhuang <haojian.zhuang@linaro.org> Reviewed-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Will Deacon <will.deacon@arm.com>
arm64: kernel: remove non-legit DT warnings when booting using ACPI
Since both CONFIG_ACPI and CONFIG_OF are enabled when booting using ACPI
tables on ARM64 platforms, we get few device tree warnings which are not
valid for ACPI boot. We can use of_have_populated_dt to check if the
device tree is populated or not before throwing out those errors.
This patch uses of_have_populated_dt to remove non legitimate device
tree warning when booting using ACPI tables.
Cc: Lorenzo Pieralisi <Lorenzo.Pieralisi@arm.com> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Will Deacon [Thu, 23 Jul 2015 12:51:46 +0000 (13:51 +0100)]
arm64: alternatives: add enable parameter to conditional asm macros
There are cases where we want to compile out both versions of an
alternative code block, so add an enable parameter to the new conditional
alternative assembly macros in the same way as alternative_insn.
James Morse [Wed, 22 Jul 2015 18:05:54 +0000 (19:05 +0100)]
arm64: kernel: Add support for Privileged Access Never
'Privileged Access Never' is a new arm8.1 feature which prevents
privileged code from accessing any virtual address where read or write
access is also permitted at EL0.
This patch enables the PAN feature on all CPUs, and modifies {get,put}_user
helpers temporarily to permit access.
This will catch kernel bugs where user memory is accessed directly.
'Unprivileged loads and stores' using ldtrb et al are unaffected by PAN.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: James Morse <james.morse@arm.com>
[will: use ALTERNATIVE in asm and tidy up pan_enable check] Signed-off-by: Will Deacon <will.deacon@arm.com>
The system register encoding generated by sys_reg() works only
for MRS/MSR(Register) operations, as we hardcode Bit20 to 1 in
mrs_s/msr_s mask. This makes it unusable for generating instructions
accessing registers with Op0 < 2(e.g, PSTATE.x with Op0=0).
As per ARMv8 ARM, (Ref: ARMv8 ARM, Section: "System instruction class
encoding overview", C5.2, version:ARM DDI 0487A.f), the instruction
encoding reserves bits [20-19] for Op0.
This patch generalises the sys_reg, mrs_s and msr_s macros, so that
we could use them to access any of the supported system register.
Cc: James Morse <james.morse@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
James Morse [Tue, 21 Jul 2015 12:23:30 +0000 (13:23 +0100)]
arm64: kernel: Add optional CONFIG_ parameter to ALTERNATIVE()
Some uses of ALTERNATIVE() may depend on a feature that is disabled at
compile time by a Kconfig option. In this case the unused alternative
instructions waste space, and if the original instruction is a nop, it
wastes time and space.
This patch adds an optional 'config' option to ALTERNATIVE() and
alternative_insn that allows the compiler to remove both the original
and alternative instructions if the config option is not defined.
Suggested-by: Catalin Marinas <catalin.marinas@arm.com> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: James Morse <james.morse@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
James Morse [Tue, 21 Jul 2015 12:23:29 +0000 (13:23 +0100)]
arm64: kernel: Add min_field_value and use '>=' for feature detection
When a new cpu feature is available, the cpu feature bits will have some
initial value, which is incremented when the feature is updated.
This patch changes 'register_value' to be 'min_field_value', and checks
the feature bits value (interpreted as a signed int) is greater than this
minimum.
Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: James Morse <james.morse@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
James Morse [Tue, 21 Jul 2015 12:23:28 +0000 (13:23 +0100)]
arm64: kernel: Add cpufeature 'enable' callback
This patch adds an 'enable()' callback to cpu capability/feature
detection, allowing features that require some setup or configuration
to get this opportunity once the feature has been detected.
Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: James Morse <james.morse@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Daniel Thompson [Wed, 22 Jul 2015 11:21:04 +0000 (12:21 +0100)]
arm64: kvm: Adopt new alternative assembler macros
Convert the dynamic patching for ARM64_HAS_SYSREG_GIC_CPUIF over to
the newly added alternative assembler macros.
Acked-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Will Deacon <will.deacon@arm.com>
Daniel Thompson [Wed, 22 Jul 2015 11:21:01 +0000 (12:21 +0100)]
arm64: alternative: Provide if/else/endif assembler macros
The existing alternative_insn macro has some limitations that make it
hard to work with. In particular the fact it takes instructions from it
own macro arguments means it doesn't play very nicely with C pre-processor
macros because the macro arguments look like a string to the C
pre-processor. Workarounds are (probably) possible but things start to
look ugly.
Introduce an alternative set of macros that allows instructions to be
presented to the assembler as normal and switch everything over to the
new macros.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Will Deacon <will.deacon@arm.com>
James Morse [Tue, 21 Jul 2015 12:23:26 +0000 (13:23 +0100)]
arm64: kernel: Add cpuid_feature_extract_field() for 4bit sign extension
Based on arch/arm/include/asm/cputype.h, this function does the
shifting and sign extension necessary when accessing cpu feature fields.
Signed-off-by: James Morse <james.morse@arm.com> Suggested-by: Russell King <linux@arm.linux.org.uk> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Mark Rutland [Tue, 21 Jul 2015 10:36:39 +0000 (11:36 +0100)]
arm64: perf: condense event number maps
Most of the cache events an architecture might support do not map well
to those provided by the ARM architecture, and as such most entries in
the event number maps are *_UNSUPPORTED. Unfortuantely as 0 is a valid
physical event identifier, the *_UNSUPPORTED macros expand to a non-zero
value and thus each unsupported event must be explicitly initialised as
such. This leads to large diffs when adding support for a new CPU, and
makes it difficult to spot the important information.
This patch follows arch/arm/ in making use of PERF_*_ALL_UNSUPPORTED
macros to initialise all entries to *_UNSUPPORTED before overriding this
for the specific events we actually support, resulting in a significant
source code reduction.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Robin Murphy [Fri, 17 Jul 2015 15:58:21 +0000 (16:58 +0100)]
arm64: dma-mapping: implement dma_get_sgtable()
The default dma_common_get_sgtable() implementation relies on the CPU
address of the buffer being a regular lowmem address. This is not always
the case on arm64, since allocations from the various DMA pools may have
remapped vmalloc addresses, rendering the use of virt_to_page() invalid.
Fix this by providing our own implementation based on the fact that we
can safely derive a physical address from the DMA address in both cases.
CC: Jon Medhurst <tixy@linaro.org> Signed-off-by: Robin Murphy <robin.murphy@arm.com>
[will: made static] Signed-off-by: Will Deacon <will.deacon@arm.com>
Will Deacon [Fri, 29 May 2015 17:28:44 +0000 (18:28 +0100)]
arm64: force CONFIG_SMP=y and remove redundant #ifdefs
Nobody seems to be producing !SMP systems anymore, so this is just
becoming a source of kernel bugs, particularly if people want to use
coherent DMA with non-shared pages.
This patch forces CONFIG_SMP=y for arm64, removing a modest amount of
code in the process.
Mark Rutland [Mon, 6 Jul 2015 11:23:54 +0000 (12:23 +0100)]
arm64: perf: factor out callchain code
We currently bundle the callchain handling code with the PMU code,
despite the fact the two are distinct, and the former can be useful even
in the absence of the latter.
Follow the example of arch/arm and factor the callchain handling into
its own file dependent on CONFIG_PERF_EVENTS rather than
CONFIG_HW_PERF_EVENTS.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
arm64: Better native ptrace support for compat tasks
The compat ptrace interface allows access to the TLS register, hardware
breakpoints and watchpoints, syscall number. However, a native task
using the native ptrace interface to debug compat tasks (e.g. multi-arch
gdb) only has access to the general and VFP register sets. The compat
ptrace interface cannot be accessed from a native task.
This patch adds a new user_aarch32_ptrace_view which contains the TLS,
hardware breakpoint/watchpoint and syscall number regsets in addition to
the existing GPR and VFP regsets. This view is backwards compatible with
the previous kernels. Core dumping of 32-bit tasks and compat ptrace are
not affected since the original user_aarch32_view is preserved.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Reported-by: Yao Qi <yao.qi@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Olof Johansson [Thu, 16 Jul 2015 20:26:16 +0000 (21:26 +0100)]
arm64: enable more compressed Image formats
Plumb up Makefile arguments for the already supported formats in the kbuild
system: lz4, bzip2, lzma, and lzo.
Note that just as with Image.gz, these images are not self-decompressing and
the booting firmware still needs to handle decompression before launching the
kernel image.
Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Will Deacon <will.deacon@arm.com>
arm64: Add support for hardware updates of the access and dirty pte bits
The ARMv8.1 architecture extensions introduce support for hardware
updates of the access and dirty information in page table entries. With
TCR_EL1.HA enabled, when the CPU accesses an address with the PTE_AF bit
cleared in the page table, instead of raising an access flag fault the
CPU sets the actual page table entry bit. To ensure that kernel
modifications to the page tables do not inadvertently revert a change
introduced by hardware updates, the exclusive monitor (ldxr/stxr) is
adopted in the pte accessors.
When TCR_EL1.HD is enabled, a write access to a memory location with the
DBM (Dirty Bit Management) bit set in the corresponding pte
automatically clears the read-only bit (AP[2]). Such DBM bit maps onto
the Linux PTE_WRITE bit and to check whether a writable (DBM set) page
is dirty, the kernel tests the PTE_RDONLY bit. In order to allow
read-only and dirty pages, the kernel needs to preserve the software
dirty bit. The hardware dirty status is transferred to the software
dirty bit in ptep_set_wrprotect() (using load/store exclusive loop) and
pte_modify().
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Mark Salter [Thu, 16 Jul 2015 17:58:53 +0000 (18:58 +0100)]
arm64: remove dead code
Commit 68234df4ea79 ("arm64: kill flush_cache_all()") removed
soft_reset() from the kernel. This was the only caller of
setup_mm_for_reboot(), so remove that also.
Signed-off-by: Mark Salter <msalter@redhat.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Robin Murphy [Fri, 10 Jul 2015 15:47:56 +0000 (16:47 +0100)]
arm64: consolidate __swiotlb_mmap
Since commit 9d3bfbb4df58 ("arm64: Combine coherent and non-coherent
swiotlb dma_ops"), __dma_common_mmap is no longer shared between two
callers, so roll it into the remaining one.
Signed-off-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
On 64bit kernel, the dump_mem gives 32 bit addresses
on the stack dump. This gives unorganized information regarding
the 64bit values on the stack. Hence, modified to get a complete 64bit memory
dump.
Sudeep Holla [Tue, 30 Jun 2015 12:56:56 +0000 (13:56 +0100)]
arm64: perf: replace arch_find_n_match_cpu_physical_id with of_cpu_device_node_get
arch_find_n_match_cpu_physical_id parses the device tree to get the
device node for a given logical cpu index. However, since ARM PMUs get
probed after the CPU device nodes are stashed while registering the
cpus, we can use of_cpu_device_node_get to avoid another DT parse.
This patch replaces arch_find_n_match_cpu_physical_id with
of_cpu_device_node_get to reuse the stashed value directly instead.
Cc: Will Deacon <will.deacon@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
ARM64 pmu prints an error message in event_init() when
no hardware PMU is available. This is pretty annoying as
it keeps printing the message for every single trial, flooding
the kernel logs, unnecessarily. The return code is sufficient for
the user to figure out the reason.
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"This update contains:
- the manual revert of the SYSCALL32 changes which caused a
regression
- a fix for the MPX vma handling
- three fixes for the ioremap 'is ram' checks.
- PAT warning fixes
- a trivial fix for the size calculation of TLB tracepoints
- handle old EFI structures gracefully
This also contains a PAT fix from Jan plus a revert thereof. Toshi
explained why the code is correct"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm/pat: Revert 'Adjust default caching mode translation tables'
x86/asm/entry/32: Revert 'Do not use R9 in SYSCALL32' commit
x86/mm: Fix newly introduced printk format warnings
mm: Fix bugs in region_is_ram()
x86/mm: Remove region_is_ram() call from ioremap
x86/mm: Move warning from __ioremap_check_ram() to the call site
x86/mm/pat, drivers/media/ivtv: Move the PAT warning and replace WARN() with pr_warn()
x86/mm/pat, drivers/infiniband/ipath: Replace WARN() with pr_warn()
x86/mm/pat: Adjust default caching mode translation tables
x86/fpu: Disable dependent CPU features on "noxsave"
x86/mpx: Do not set ->vm_ops on MPX VMAs
x86/mm: Add parenthesis for TLB tracepoint size calculation
efi: Handle memory error structures produced based on old versions of standard
"No, the default values need to be set to the fallback types,
i.e. minimal supported mode. For WC and WT, UC is the fallback type.
When PAT is disabled, pat_init() does update the tables below to
enable WT per the default BIOS setup. However, when PAT is enabled,
but CPU has PAT -errata, WT falls back to UC per the default values."
The CQM task events are not safe to be called from within interrupt
context because they require performing an IPI to read the counter value
on all sockets. And performing IPIs from within IRQ context is a
"no-no".
Make do with the last read counter value currently event in
event->count when we're invoked in this context.
Reported-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Matt Fleming <matt.fleming@intel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vikas Shivappa <vikas.shivappa@intel.com> Cc: Kanaka Juvva <kanaka.d.juvva@intel.com> Cc: Will Auld <will.auld@intel.com> Cc: <stable@vger.kernel.org> Link: http://lkml.kernel.org/r/1437490509-15373-1-git-send-email-matt@codeblueprint.co.uk Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Merge tag 'usb-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here's a few USB and PHY fixes for 4.2-rc4.
Nothing major, the shortlog has the full details.
All of these have been in linux-next successfully"
* tag 'usb-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (21 commits)
USB: OHCI: fix bad #define in ohci-tmio.c
cdc-acm: Destroy acm_minors IDR on module exit
usb-storage: Add ignore-device quirk for gm12u320 based usb mini projectors
usb-storage: ignore ZTE MF 823 card reader in mode 0x1225
USB: OHCI: Fix race between ED unlink and URB submission
usb: core: lpm: set lpm_capable for root hub device
xhci: do not report PLC when link is in internal resume state
xhci: prevent bus_suspend if SS port resuming in phase 1
xhci: report U3 when link is in resume state
xhci: Calculate old endpoints correctly on device reset
usb: xhci: Bugfix for NULL pointer deference in xhci_endpoint_init() function
xhci: Workaround to get D3 working in Intel xHCI
xhci: call BIOS workaround to enable runtime suspend on Intel Braswell
usb: dwc3: Reset the transfer resource index on SET_INTERFACE
usb: gadget: udc: core: Fix argument of dma_map_single for IOMMU
usb: gadget: mv_udc_core: fix phy_regs I/O memory leak
usb: ulpi: ulpi_init should be executed in subsys_initcall
phy: berlin-usb: fix divider for BG2
phy: berlin-usb: fix divider for BG2CD
phy/pxa: add HAS_IOMEM dependency
...
Merge tag 'trace-v4.2-rc2-fix3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull ftrace fix from Steven Rostedt:
"Back in 3.16 the ftrace code was redesigned and cleaned up to remove
the double iteration list (one for registered ftrace ops, and one for
registered "global" ops), to just use one list. That simplified the
code but also broke the function tracing filtering on pid.
This updates the code to handle the filtering again with the new
logic"
* tag 'trace-v4.2-rc2-fix3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace: Fix breakage of set_ftrace_pid
Merge branch 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/nvdimm
Pull libnvdimm fix from Dan Williams:
"A minor fix for the libnvdimm subsystem.
This is not critical. The problem can be worked around in userspace
by putting the namespace temporarily into raw mode
(ndctl_namespace_set_raw_mode() from libndctl), but that is awkward
for management utilities.
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/nvdimm:
libnvdimm: fix namespace seed creation
Merge tag 'md/4.2-fixes' of git://neil.brown.name/md
Pull md fixes from Neil Brown:
"Some md fixes for 4.2
Several are tagged for -stable.
A few aren't because they are not very, serious or because they are in
the 'experimental' cluster code"
* tag 'md/4.2-fixes' of git://neil.brown.name/md:
md/raid5: clear R5_NeedReplace when no longer needed.
Fix read-balancing during node failure
md-cluster: fix bitmap sub-offset in bitmap_read_sb
md: Return error if request_module fails and returns positive value
md: Skip cluster setup in case of error while reading bitmap
md/raid1: fix test for 'was read error from last working device'.
md: Skip cluster setup for dm-raid
md: flush ->event_work before stopping array.
md/raid10: always set reshape_safe when initializing reshape_position.
md/raid5: avoid races when changing cache size.
Dan Williams [Sat, 25 Jul 2015 03:42:34 +0000 (23:42 -0400)]
libnvdimm: fix namespace seed creation
A new BLK namespace "seed" device is created whenever the current seed
is successfully probed. However, if that namespace is assigned to a BTT
it may never directly experience a successful probe as it is a
subordinate device to a BTT configuration.
The effect of the current code is that no new namespaces can be
instantiated, after the seed namespace, to consume available BLK DPA
capacity. Fix this by treating a successful BTT probe event as a
successful probe event for the backing namespace.
Reported-by: Nicholas Moulin <nicholas.w.moulin@linux.intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Four smaller fixes for the current series. This contains:
- A fix for clones of discard bio's, that can cause data corruption.
From Martin.
- A fix for null_blk, where in certain queue modes it could access a
request after it had been freed. From Mike Krinkin.
- An error handling leak fix for blkcg, from Tejun.
- Also from Tejun, export of the functions that a file system needs
to implement cgroup writeback support"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: Do a full clone when splitting discard bios
block: export bio_associate_*() and wbc_account_io()
blkcg: fix gendisk reference leak in blkg_conf_prep()
null_blk: fix use-after-free problem
Merge branch 'for-4.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"A couple important fixes.
- A block layer change which removed restriction on max transfer size
led to silent data corruption on some devices. A new quirk is
added to restore the old size limit for the reported device. If it
gets reported on more devices, we might have to consider restoring
the restriction for ATA devices by default.
- There finally is a SSD which is confirmed to cause data corruption
on TRIM regardless of which flavor is used. A new quirk is added
and the device is blacklisted
- Other device-specific workarounds"
* 'for-4.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: Do not blacklist M510DC
libata: increase the timeout when setting transfer mode
libata: add ATA_HORKAGE_MAX_SEC_1024 to revert back to previous max_sectors limit
libata: force disable trim for SuperSSpeed S238
libata: add ATA_HORKAGE_NOTRIM
libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk for HP 250GB SATA disk VB0250EAVER
ata: pmp: add quirk for Marvell 4140 SATA PMP
Merge tag 'mmc-4.2-rc3' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC fixes from Ulf Hansson:
"Here are some mmc fixes intended for v4.2 rc4.
Note, most of the changes are for the sdhci-esdhc-imx controller,
which also required us to modify some related DTS files. Those
changes have been acked by the SoC maintainer.
MMC core:
- Fix a reference inbalance issue for power_ro_lock_show() sysfs handler
MMC host:
- omap_hsmmc: Fix IRQ errorhandling for CD, DTO, and CRC
- sdhci: Prevent a kernel panic while using DMA
- mtk-sd: Let it depend on HAS_DMA to prevent build errors
- sdhci-esdhc: Make 8BIT bus work
- sdhci-esdhc-imx: Fix some regressions for DT based platforms
- sdhci-pxav3: Fix a regression for DT based platforms"
* tag 'mmc-4.2-rc3' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: sdhci-pxav3: fix platform_data is not initialized
dts: mmc: fsl-imx-esdhc: remove fsl,cd-controller support
mmc: sdhci-esdhc-imx: clear f_max in boarddata
mmc: sdhci-esdhc-imx: remove duplicated dts parsing
mmc: sdhci: make max-frequency property in device tree work
mmc: sdhci-esdhc-imx: move all non dt probe code into one function
mmc: sdhci-esdhc-imx: fix cd regression for dt platform
dts: imx7: fix sd card gpio polarity specified in device tree
dts: imx25: fix sd card gpio polarity specified in device tree
dts: imx6: fix sd card gpio polarity specified in device tree
dts: imx53: fix sd card gpio polarity specified in device tree
dts: imx51: fix sd card gpio polarity specified in device tree
mmc: sdhci-esdhc: Make 8BIT bus work
mmc: block: Add missing mmc_blk_put() in power_ro_lock_show()
mmc: MMC_MTK should depend on HAS_DMA
mmc: sdhci check parameters before call dma_free_coherent
mmc: omap_hsmmc: Handle BADA, DEB and CEB interrupts
mmc: omap_hsmmc: Fix DTO and DCRC handling
Merge tag 'regulator-fix-v4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"As well as some driver specific fixes there's several fixes here for
the core support for regulators supplying other regulators fixing both
an issue with ACPI support (which had never been tested before) and
some error handling and device removal issues that Javier noticed"
* tag 'regulator-fix-v4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: core: Fix memory leak in regulator_resolve_supply()
regulator: core: Increase refcount for regulator supply's module
regulator: core: Handle full constraints systems when resolving supplies
regulator: 88pm800: fix LDO vsel_mask value
regulator: max8973: Fix up control flag option for bias control
regulator: s2mps11: Fix GPIO suspend enable shift wrapping bug
Merge tag 'spi-fix-v4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A small collection of pretty much unremarkable driver specific fixes
here plus the addition of a new device ID to spidev which requires no
other code changes"
* tag 'spi-fix-v4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: imx: Fix small DMA transfers
spi: zynq: missing break statement
spi: SPI_ZYNQMP_GQSPI should depend on HAS_DMA
spi: spidev: add compatible value for LTC2488
spi: img-spfi: fix support for speeds up to 1/4th input clock
Merge tag 'sound-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This has been a calm week again: one minor lockdep fix for PCM core,
and the most of the rest are HD-audio quirks and fixups for various
chips and machines"
* tag 'sound-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Add headset mic pin quirk for a Dell device
ALSA: hda - remove one pin from ALC292_STANDARD_PINS
ALSA: hda - Add new GPU codec ID 0x10de007d to snd-hda
ALSA: hda: add new AMD PCI IDs with proper driver caps
ALSA: hda - Fix Skylake codec timeout
ALSA: hda - Add headset mic support for Acer Aspire V5-573G
ALSA: sparc: Add missing kfree in error path
ALSA: pcm: Fix lockdep warning with nonatomic PCM ops
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- kernel crash fixes for multitouch and wacom drivers, by Brent Adam
and Dan Carpenter
- cp2112 data packet race condition corruption fix, by Antonio Borneo
- a few new device IDs for wacom and microsoft drivers
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: cp2112: fix to force single data-report reply
HID: wacom: Enable pad device for older Bamboo Touch tablets
HID: multitouch: Fix fields from pen report ID being interpreted for multitouch
HID: microsoft: Add quirk for MS Surface Type/Touch cover
HID: wacom: NULL dereferences on error in probe()
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Aome amdgpu, one i915, one ttm and one hlcdc, nothing too scary.
All seems fine for about this time"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/ttm: recognize ARM64 arch in ioprot handler
drm/amdgpu/cz/dpm: properly report UVD and VCE clock levels
drm/amdgpu/cz: implement voltage validation properly
drm/amdgpu: add VCE harvesting instance query
drm/amdgpu: implement VCE 3.0 harvesting support (v4)
drm/amdgpu/dce10: Re-set VBLANK interrupt state when enabling a CRTC
drm/amdgpu/dce11: Re-set VBLANK interrupt state when enabling a CRTC
drm: Stop resetting connector state to unknown
drm/i915: Use two 32bit reads for select 64bit REG_READ ioctls
drm: atmel-hlcdc: fix vblank initial state
Commit 4104d326b670 ("ftrace: Remove global function list and call function
directly") simplified the ftrace code by removing the global_ops list with a
new design. But this cleanup also broke the filtering of PIDs that are added
to the set_ftrace_pid file.
Add back the proper hooks to have pid filtering working once again.
Cc: stable@vger.kernel.org # 3.16+ Reported-by: Matt Fleming <matt@console-pimps.org> Reported-by: Richard Weinberger <richard.weinberger@gmail.com> Tested-by: Matt Fleming <matt@console-pimps.org> Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Input: goodix - fix touch coordinates on WinBook TW100 and TW700
The touchscreen on the WinBook TW100 and TW700 don't match the default
display, with 0,0 touches being reported when touching at the bottom
right of the screen.
It's unfortunately impossible to detect this problem with data from the
DSDT, or other auxiliary metadata, so fallback to quirking this specific
model of tablet instead.
Devices may declare more LEDs than what is known to input-leds
(HID does this for some devices). Instead of showing ugly warnings
on connect and, even worse, oopsing on disconnect, let's simply
ignore LEDs that are not known to us.
Mark Brown [Fri, 24 Jul 2015 15:19:25 +0000 (16:19 +0100)]
Merge remote-tracking branches 'regulator/fix/88pm800', 'regulator/fix/max8973', 'regulator/fix/s2mps11' and 'regulator/fix/supply' into regulator-linus
DMA transfers must be greater than the watermark level size. spi_imx->rx_wml
and spi_imx->tx_wml contain the watermark level in 32bit words whereas struct
spi_transfer contains the transfer len in bytes. Fix the check if DMA is
possible for a transfer accordingly. This fixes transfers with sizes between
33 and 128 bytes for which previously was claimed that DMA is possible.
Fixes: f62caccd12c17e4 (spi: spi-imx: add DMA support) Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Cc: stable@vger.kernel.org Signed-off-by: Mark Brown <broonie@kernel.org>
x86/asm/entry/32: Revert 'Do not use R9 in SYSCALL32' commit
This change reverts most of commit 53e9accf0f 'Do not use R9 in
SYSCALL32'. I don't yet understand how, but code in that commit
sometimes fails to preserve EBP.
See https://bugzilla.kernel.org/show_bug.cgi?id=101061
"Problems while executing 32-bit code on AMD64"
Reported-and-tested-by: Krzysztof A. Sobiecki <sobkas@gmail.com> Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Alexei Starovoitov <ast@plumgrid.com> Cc: Will Drewry <wad@chromium.org> Cc: Kees Cook <keescook@chromium.org> CC: x86@kernel.org Link: http://lkml.kernel.org/r/1437740203-11552-1-git-send-email-dvlasenk@redhat.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
mmc: sdhci-pxav3: fix platform_data is not initialized
pdev->dev.platform_data is not initialized if match is true in function
sdhci_pxav3_probe. Just local variable pdata is assigned the return value
from function pxav3_get_mmc_pdata().
static int sdhci_pxav3_probe(struct platform_device *pdev) {
struct sdhci_pxa_platdata *pdata = pdev->dev.platform_data;
...
if (match) {
ret = mmc_of_parse(host->mmc);
if (ret)
goto err_of_parse;
sdhci_get_of_property(pdev);
pdata = pxav3_get_mmc_pdata(dev);
}
...
}
After commit 8d86e4fcccf6 ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()"),
we do not need those duplicated parsing anymore.
Note: fsl,cd-controller is also deleted due to the driver does
not support controller card detection anymore after switch to runtime pm.
And there's no user of it right now in device tree.
wp-gpios is kept because we're still support fsl,wp-controller,
so we need a way to check if it's gpio wp or controller wp.
mmc: sdhci: make max-frequency property in device tree work
Device tree provides option to specify the max freqency with property
"max-frequency" in dts and common parse function mmc_of_parse() will
parse it and use this value to set host->f_max to tell the MMC core
the maxinum frequency the host works.
However, current sdhci driver will finally overwrite this value with
host->max_clk regardless of the max-frequency property.
This patch makes sure not overwrite the max-frequency set from device
tree and do basic sanity check.
mmc: sdhci-esdhc-imx: move all non dt probe code into one function
This is an incremental fix of commit e62bd351b("mmc: sdhci-esdhc-imx: Do not break platform data boards").
After commit 8d86e4fcccf6 ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()"),
we do not need to run the check of boarddata->wp_type/cd_type/max_bus_width
again for dt platform since those are already handled by mmc_of_parse().
Current code only exclude the checking of wp_type for dt platform which
does not make sense.
This patch moves all non dt probe code into one function.
Besides, since we only support SD3.0/eMMC HS200 for dt platform, the
support_vsel checking and ultra high speed pinctrl state are also merged
into sdhci_esdhc_imx_probe_dt.
Then we have two separately probe function for dt and non dt type.
This can make the driver probe more clearly.
mmc: sdhci-esdhc-imx: fix cd regression for dt platform
Current card detect probe process is that when driver finds a valid
ESDHC_CD_GPIO, it will clear the quirk SDHCI_QUIRK_BROKEN_CARD_DETECTION
which is set by default for all esdhc/usdhc controllers.
Then host driver will know there's a valid card detect function.
Commit 8d86e4fcccf6 ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()")
breaks GPIO CD function for dt platform that it will return directly
when find ESDHC_CD_GPIO for dt platform which result in the later wrongly
to keep SDHCI_QUIRK_BROKEN_CARD_DETECTION for all dt platforms.
Then MMC_CAP_NEEDS_POLL will be used instead even there's a valid
GPIO card detect.
This patch adds back this function and follows the original approach to
clear the quirk if find an valid CD GPIO for dt platforms.
dts: imx7: fix sd card gpio polarity specified in device tree
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
dts: imx25: fix sd card gpio polarity specified in device tree
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
dts: imx6: fix sd card gpio polarity specified in device tree
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
dts: imx53: fix sd card gpio polarity specified in device tree
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
dts: imx51: fix sd card gpio polarity specified in device tree
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Support for 8BIT bus with was added some time ago to sdhci-esdhc but
then missed to remove the 8BIT from the reserved bit mask which made
8BIT non functional.
Fixes: 66b50a00992d ("mmc: esdhc: Add support for 8-bit bus width and..") Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Vignesh R [Tue, 16 Jun 2015 10:37:18 +0000 (16:07 +0530)]
mmc: omap_hsmmc: Handle BADA, DEB and CEB interrupts
Sometimes BADA, DEB or CEB error interrupts occur when sd card is
unplugged during data transfer. These interrupts are currently ignored
by the interrupt handler. But, this results in card not being
recognised on subsequent insertion. This is because mmcqd is waiting
forever for the data transfer(for which error occurred) to complete.
Fix this, by reporting BADA, DEB, CEB errors to mmc-core as -EILSEQ, so
that the core can do appropriate handling.
Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Andreas Fenkart <afenkart@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
DTO/DCRC errors were not being informed to the mmc core since
commit ae4bf788ee9b ("mmc: omap_hsmmc: consolidate error report handling of
HSMMC IRQ"). This commit made sure 'end_trans' is never set on DTO/DCRC
errors. This is because after this commit 'host->data' is checked after
it has been cleared to NULL by omap_hsmmc_dma_cleanup().
Because 'end_trans' is never set, omap_hsmmc_xfer_done() is never invoked
making core layer not to be aware of DTO/DCRC errors. Because of this
any command invoked after DTO/DCRC error leads to a hang.
Fix this by checking for 'host->data' before it is actually cleared.
CC: stable@vger.kernel.org Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Andreas Fenkart <afenkart@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
During a node failure, We need to suspend read balancing so that the
reads are directed to the first device and stale data is not read.
Suspending writes is not required because these would be recorded and
synced eventually.
A new flag MD_CLUSTER_SUSPEND_READ_BALANCING is set in recover_prep().
area_resyncing() will respond true for the entire devices if this
flag is set and the request type is READ. The flag is cleared
in recover_done().
md-cluster: fix bitmap sub-offset in bitmap_read_sb
bitmap_read_sb is modifying mddev->bitmap_info.offset. This works for
the first bitmap read. However, when multiple bitmaps need to be opened
by the same node, it ends up corrupting the offset. Fix it by using a
local variable.
Also, bitmap_read_sb is not required in bitmap_copy_from_slot since
it is called in bitmap_create. Remove bitmap_read_sb().
md: Return error if request_module fails and returns positive value
request_module() can return 256 (process exited) in some cases,
which is not as specified in the documentation before the
request_module() definition. Convert the error to -ENOENT.
The positive error number results in bitmap_create() returning
a value that is meant to be an error but doesn't look like one,
so it is dereferenced as a point and causes a crash.
(not needed for stable as this is "experimental" code) Fixes: edb39c9deda8 ("Introduce md_cluster_operations to handle cluster functions") Signed-off-By: Goldwyn Rodrigues <rgoldwyn@suse.com> Signed-off-by: NeilBrown <neilb@suse.com>
md: Skip cluster setup in case of error while reading bitmap
If the bitmap read fails, the error code set is -EINVAL. However,
we don't check for errors and go ahead with cluster_setup.
Skip the cluster setup in case of error.
md/raid1: fix test for 'was read error from last working device'.
When we get a read error from the last working device, we don't
try to repair it, and don't fail the device. We simple report a
read error to the caller.
However the current test for 'is this the last working device' is
wrong.
When there is only one fully working device, it assumes that a
non-faulty device is that device. However a spare which is rebuilding
would be non-faulty but so not the only working device.
So change the test from "!Faulty" to "In_sync". If ->degraded says
there is only one fully working device and this device is in_sync,
this must be the one.
This bug has existed since we allowed read_balance to read from
a recovering spare in v3.0
Reported-and-tested-by: Alexander Lyakas <alex.bolshoy@gmail.com> Fixes: 76073054c95b ("md/raid1: clean up read_balance.") Cc: stable@vger.kernel.org (v3.0+) Signed-off-by: NeilBrown <neilb@suse.com>
Dave Airlie [Fri, 24 Jul 2015 01:52:35 +0000 (11:52 +1000)]
Merge tag 'topic/drm-fixes-2015-07-23' of git://anongit.freedesktop.org/drm-intel into drm-fixes
Regression fix for systemd getting confused about unknown connector state
after resume. Just stop setting the state to unknown, turned out to be a
silly idea anyway. What drivers imo really should do (and i915 still does
that) is forcing a full reprobe on resume to make sure connector changes
while suspended are caught. Most drivers seem to get this wrong. Otoh it
took us years to get fixes merged where some probe races resulted in
eating uevents, I guess userspace expectations for reliable hpd are just
really low :(
* tag 'topic/drm-fixes-2015-07-23' of git://anongit.freedesktop.org/drm-intel:
drm: Stop resetting connector state to unknown
Dave Airlie [Fri, 24 Jul 2015 01:51:18 +0000 (11:51 +1000)]
Merge branch 'drm-fixes-4.2' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Some amdgpu fixes.
* 'drm-fixes-4.2' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu/cz/dpm: properly report UVD and VCE clock levels
drm/amdgpu/cz: implement voltage validation properly
drm/amdgpu: add VCE harvesting instance query
drm/amdgpu: implement VCE 3.0 harvesting support (v4)
drm/amdgpu/dce10: Re-set VBLANK interrupt state when enabling a CRTC
drm/amdgpu/dce11: Re-set VBLANK interrupt state when enabling a CRTC
Peter Hurley [Mon, 13 Jul 2015 01:05:26 +0000 (21:05 -0400)]
serial: core: Fix crashes while echoing when closing
While closing, new rx data may be received after the input buffers
have been flushed but before stop_rx() halts receiving [1]. The
new data might not be processed by flush_to_ldisc() until after
uart_shutdown() and normal input processing is re-enabled (ie.,
tty->closing = 0). The race is outlined below:
Input processing must be prevented from echoing (tty->closing = 1)
until _after_ the input buffers have been flushed again at the end
of uart_close().
[1] In fact, some input may actually be buffered _after_ stop_rx()
since the rx interrupt may have already triggered but not yet been
handled when stop_rx() disables rx interrupts.
Fixes: 2e758910832d ("serial: core: Flush ldisc after dropping port
mutex in uart_close()") Reported-by: Robert Elliott <elliott@hp.com> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-beck.git / log