Daniel Vetter [Fri, 14 Dec 2012 15:01:25 +0000 (16:01 +0100)]
drm/i915: paper over missed irq issues with force wake voodoo
Two things seem to do the trick on my ivb machine here:
- prevent the gt from powering down while waiting for seqno
notification interrupts by grabbing the force_wake in get_irq (and
dropping it in put_irq again).
- ordering writes from the ring's CS by reading a CS register, ACTHD
seems to work.
Only the blt&bsd ring on ivb seem to be massively affected by this,
but for paranoia do this dance also on the render ring and on snb
(i.e. all gpus with forcewake).
Tested with Eric's glCopyPixels loop which without this patch scores a
missed irq every few seconds.
This patch needs my forcewake rework to use a spinlock instead of
dev->struct_mutex.
After crawling through docs a lot I've found the following nugget:
Keith Packard [Fri, 6 Jan 2012 19:48:38 +0000 (11:48 -0800)]
drm/i915: Hold gt_lock across forcewake register reads
Along with the previous patch to make the reset operation protected by
the gt_lock as well, this ensures that all register read operations
will occur with the forcewake hardware enabled. As an added bonus,
this makes read operations more efficient by taking the spinlock only
once per read instead of twice.
Signed-off-by: Keith Packard <keithp@keithp.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Wed, 14 Dec 2011 12:57:03 +0000 (13:57 +0100)]
drm/i915: protect force_wake_(get|put) with the gt_lock
The problem this patch solves is that the forcewake accounting
necessary for register reads is protected by dev->struct_mutex. But the
hangcheck and error_capture code need to access registers without
grabbing this mutex because we hold it while waiting for the gpu.
So a new lock is required. Because currently the error_state capture
is called from the error irq handler and the hangcheck code runs from
a timer, it needs to be an irqsafe spinlock (note that the registers
used by the irq handler (neglecting the error handling part) only uses
registers that don't need the forcewake dance).
We could tune this down to a normal spinlock when we rework the
error_state capture and hangcheck code to run from a workqueue. But
we don't have any read in a fastpath that needs forcewake, so I've
decided to not care much about overhead.
This prevents tests/gem_hangcheck_forcewake from i-g-t from killing my
snb on recent kernels - something must have slightly changed the
timings. On previous kernels it only trigger a WARN about the broken
locking.
v2: Drop the previous patch for the register writes.
v3: Improve the commit message per Chris Wilson's suggestions.
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com> Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-Off-by: Daniel Vetter <daniel.vetter at ffwll.ch> Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com> Signed-off-by: Keith Packard <keithp@keithp.com>
Jesse Barnes [Fri, 13 Jan 2012 23:48:39 +0000 (15:48 -0800)]
drm/i915: sprite init failure on pre-SNB is not a failure
We can call the plane init function unconditionally, but don't need to
complain if it fails, since that will only happen if we're out of
memory (and other things will fail) or if we're on the wrong platform
(which is ok).
And remove the DRM_ERRORs from the sprite code itself to avoid dmesg
spam.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Reviewed-by: Keith Packard <keithp@keithp.com> Signed-off-by: Keith Packard <keithp@keithp.com>
Rohit Jain [Thu, 12 Jan 2012 06:49:44 +0000 (12:19 +0530)]
drm/i915: VBT Parser cleanup for eDP block
Support for parsing parameters for S3D support and T3 optimization
support is implemented. The order for the bdb_edp struct was also
made similar to that indicated in spec.
Jesse Barnes [Thu, 12 Jan 2012 22:51:17 +0000 (14:51 -0800)]
drm/i915: mask transcoder select bits before setting them on LVDS
The transcoder port may changed from mode set to mode set, so make sure
to mask out the selection bits before setting the right ones or we'll
get black screens when going from transcoder B to A.
Tested-by: Vincent Vanackere <vincent.vanackere@gmail.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Reviewed-by: Keith Packard <keithp@keithp.com> Signed-off-by: Keith Packard <keithp@keithp.com>
Duncan Laurie [Tue, 25 Oct 2011 22:42:21 +0000 (15:42 -0700)]
CHROMIUM: i915: Add DMI override to skip CRT initialization on ZGB
This is the method used to override LVDS in intel_lvds and appears to be
an effective way to ensure that the driver does not enable VGA hotplug.
This is the same patch from 2.6.32 kernel in R12 but ported to 2.6.38,
will send upstream next.
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
BUG=chrome-os-partner:117
TEST=Check PORT_HOTPLUG_EN to see if hotplug interrupt is disabled.
Run the following command as root, specifically looking at bit 9:
mmio_read32 $[$(pci_read32 0 2 0 0x10) + 0x61110] = 0x00000000
Change-Id: Id8240f9fb31d058d8d79ee72f7b4615c43893f5a
Reviewed-on: http://gerrit.chromium.org/gerrit/1390 Reviewed-by: Olof Johansson <olofj@chromium.org> Tested-by: Duncan Laurie <dlaurie@chromium.org> Signed-off-by: Keith Packard <keithp@keithp.com>
Linus Torvalds [Tue, 10 Jan 2012 19:04:36 +0000 (11:04 -0800)]
Merge branch 'drm-core-next' of git://people.freedesktop.org/~airlied/linux
* 'drm-core-next' of git://people.freedesktop.org/~airlied/linux: (307 commits)
drm/nouveau/pm: fix build with HWMON off
gma500: silence gcc warnings in mid_get_vbt_data()
drm/ttm: fix condition (and vs or)
drm/radeon: double lock typo in radeon_vm_bo_rmv()
drm/radeon: use after free in radeon_vm_bo_add()
drm/sis|via: don't return stack garbage from free_mem ioctl
drm/radeon/kms: remove pointless CS flags priority struct
drm/radeon/kms: check if vm is supported in VA ioctl
drm: introduce drm_can_sleep and use in intel/radeon drivers. (v2)
radeon: Fix disabling PCI bus mastering on big endian hosts.
ttm: fix agp since ttm tt rework
agp: Fix multi-line warning message whitespace
drm/ttm/dma: Fix accounting error when calling ttm_mem_global_free_page and don't try to free freed pages.
drm/ttm/dma: Only call set_pages_array_wb when the page is not in WB pool.
drm/radeon/kms: sync across multiple rings when doing bo moves v3
drm/radeon/kms: Add support for multi-ring sync in CS ioctl (v2)
drm/radeon: GPU virtual memory support v22
drm: make DRM_UNLOCKED ioctls with their own mutex
drm: no need to hold global mutex for static data
drm/radeon/benchmark: common modes sweep ignores 640x480@32
...
Fix up trivial conflicts in radeon/evergreen.c and vmwgfx/vmwgfx_kms.c
Linus Torvalds [Tue, 10 Jan 2012 18:55:52 +0000 (10:55 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (64 commits)
Input: tc3589x-keypad - add missing kerneldoc
Input: ucb1400-ts - switch to using dev_xxx() for diagnostic messages
Input: ucb1400_ts - convert to threaded IRQ
Input: ucb1400_ts - drop inline annotations
Input: usb1400_ts - add __devinit/__devexit section annotations
Input: ucb1400_ts - set driver owner
Input: ucb1400_ts - convert to use dev_pm_ops
Input: psmouse - make sure we do not use stale methods
Input: evdev - do not block waiting for an event if fd is nonblock
Input: evdev - if no events and non-block, return EAGAIN not 0
Input: evdev - only allow reading events if a full packet is present
Input: add driver for pixcir i2c touchscreens
Input: samsung-keypad - implement runtime power management support
Input: tegra-kbc - report wakeup key for some platforms
Input: tegra-kbc - add device tree bindings
Input: add driver for AUO In-Cell touchscreens using pixcir ICs
Input: mpu3050 - configure the sampling method
Input: mpu3050 - ensure we enable interrupts
Input: mpu3050 - add of_match table for device-tree probing
Input: sentelic - document the latest hardware
...
Fix up fairly trivial conflicts (device tree matching conflicting with
some independent cleanups) in drivers/input/keyboard/samsung-keypad.c
Linus Torvalds [Tue, 10 Jan 2012 18:48:28 +0000 (10:48 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (68 commits)
hid-input/battery: add FEATURE quirk
hid-input/battery: remove battery_val
hid-input/battery: power-supply type really *is* a battery
hid-input/battery: make the battery setup common for INPUTs and FEATUREs
hid-input/battery: deal with both FEATURE and INPUT report batteries
hid-input/battery: add quirks for battery
hid-input/battery: remove apparently redundant kmalloc
hid-input: add support for HID devices reporting Battery Strength
HID: hid-multitouch: add support 9 new Xiroku devices
HID: multitouch: add support for 3M 32"
HID: multitouch: add support of Atmel multitouch panels
HID: usbhid: defer LED setting to a workqueue
HID: usbhid: hid-core: submit queued urbs before suspend
HID: usbhid: remove LED_ON
HID: emsff: use symbolic name instead of hardcoded PID constant
HID: Enable HID_QUIRK_MULTI_INPUT for Trio Linker Plus II
HID: Kconfig: fix syntax
HID: introduce proper dependency of HID_BATTERY on POWER_SUPPLY
HID: multitouch: support PixArt optical touch screen
HID: make parser more verbose about parsing errors by default
...
Fix up rename/delete conflict in drivers/hid/hid-hyperv.c (removed in
staging, moved in this branch) and similarly for the rules for same file
in drivers/staging/hv/{Kconfig,Makefile}.
Linus Torvalds [Tue, 10 Jan 2012 18:36:08 +0000 (10:36 -0800)]
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
SCSI updates for post 3.2 merge window
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (67 commits)
[SCSI] lpfc 8.3.28: Update driver version to 8.3.28
[SCSI] lpfc 8.3.28: Add Loopback support for SLI4 adapters
[SCSI] lpfc 8.3.28: Critical Miscellaneous fixes
[SCSI] Lpfc 8.3.28: FC and SCSI Discovery Fixes
[SCSI] lpfc 8.3.28: Add support for ABTS failure handling
[SCSI] lpfc 8.3.28: SLI fixes and added SLI4 support
[SCSI] lpfc 8.3.28: Miscellaneous fixes in sysfs and mgmt interfaces
[SCSI] mpt2sas: Removed redundant calling of _scsih_probe_devices() from _scsih_probe
[SCSI] mac_scsi: Remove obsolete IRQ_FLG_* users
[SCSI] qla4xxx: Update driver version to 5.02.00-k10
[SCSI] qla4xxx: check for FW alive before calling chip_reset
[SCSI] qla4xxx: Fix qla4xxx_dump_buffer to dump buffer correctly
[SCSI] qla4xxx: Fix the IDC locking mechanism
[SCSI] qla4xxx: Wait for disable_acb before doing set_acb
[SCSI] qla4xxx: Don't recover adapter if device state is FAILED
[SCSI] qla4xxx: fix call trace on rmmod with ql4xdontresethba=1
[SCSI] qla4xxx: Fix CPU lockups when ql4xdontresethba set
[SCSI] qla4xxx: Perform context resets in case of context failures.
[SCSI] iscsi class: export pid of process that created
[SCSI] mpt2sas: Remove unused duplicate diag_buffer_enable param
...
Linus Torvalds [Tue, 10 Jan 2012 18:29:23 +0000 (10:29 -0800)]
Merge git://www.linux-watchdog.org/linux-watchdog
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: omap_wdt.c: fix the WDIOC_GETBOOTSTATUS ioctl if not implemented.
watchdog: new driver for VIA chipsets
watchdog: ath79_wdt: flush register writes
drivers/watchdog/lantiq_wdt.c: drop iounmap for devm_ allocated data
watchdog: documentation: describe nowayout in coversion-guide
watchdog: documentation: update index file
watchdog: Convert wm831x driver to devm_kzalloc()
watchdog: add nowayout helpers to Watchdog Timer Driver Kernel API
watchdog: convert drivers/watchdog/* to use module_platform_driver()
watchdog: Use DEFINE_SPINLOCK() for static spinlocks
watchdog: Convert Wolfson drivers to module_platform_driver
Linus Torvalds [Tue, 10 Jan 2012 18:20:34 +0000 (10:20 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (40 commits)
regulator: set constraints.apply_uV to 0 in of_get_fixed_voltage_config
regulator: max8925: fix enabled/disabled judgement mistake
regulator: add regulator_bulk_force_disable function
regulator: pass regulator_register of_node in fixed voltage driver
regulator: add regulator_force_disable() definition for !CONFIG_REGULATOR
regulator: Enable supply regulator if child rail is enabled.
regulator: mc13892: Convert to devm_kzalloc()
regulator: mc13783: Convert to devm_kzalloc()
regulator: Fix checking return value of create_regulator
regulator: Fix the error handling if create_regulator fails
regulator: Export regulator_is_supported_voltage()
regulator: mc13892: add device tree probe support
regulator: mc13892: remove the unnecessary prefix from regulator name
regulator: Convert wm831x regulator drivers to devm_kzalloc()
regulator: da9052: Staticize non-exported symbols
regulator: Replace kzalloc with devm_kzalloc and if-else with a switch-case for da9052-regulator
regulator: Update da9052-regulator for DT changes
regulator: DA9052/53 Regulator support
regulator: pass device_node to of_get_regulator_init_data()
regulator: If a single voltage is set with device tree then set apply_uV
...
Linus Torvalds [Tue, 10 Jan 2012 18:19:57 +0000 (10:19 -0800)]
Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (31 commits)
pinctrl: remove unnecessary max pin number
pinctrl: correct a offset while enumerating pins
pinctrl: some typo fixes
pinctrl: rename U300 and SIRF pin controllers
pinctrl: pass name instead of device to pin_config_*
pinctrl: add "struct seq_file;" to pinconf.h
pinctrl: conjure names for unnamed pins
pinctrl: add a group-specific hog macro
pinctrl: don't create a device for each pin controller
arm/u300: don't use PINMUX_MAP_PRIMARY*
pinctrl: implement PINMUX_MAP_SYS_HOG
pinctrl: add a pin config interface
pinctrl/coh901: driver to request its pins
pinctrl: u300-pinmux: register proper GPIO ranges
pinctrl: move the U300 GPIO driver to pinctrl
ARM: u300: localize GPIO assignments
pinctrl: make it possible to add multiple maps
pinctrl: make a copy of pinmux map
pinctrl: GPIO direction support for muxing
pinctrl: print pin range in GPIO range debugs
...
Linus Torvalds [Tue, 10 Jan 2012 18:19:17 +0000 (10:19 -0800)]
Merge branch 'upstream-linus' of git://github.com/jgarzik/libata-dev
* 'upstream-linus' of git://github.com/jgarzik/libata-dev:
ahci: support the STA2X11 I/O Hub
pata_bf54x: fix BMIDE status register emulation
ata: add ata port hibernate callbacks
ata: update ata port's runtime status during system resume
[SCSI] runtime resume parent for child's system-resume
ahci: platform support for suspend/resume
libata-core: kill duplicate statement in ata_do_set_mode()
pata_of_platform: remove direct dependency on OF_IRQ
SATA/PATA: convert drivers/ata/* to use module_platform_driver()
pata_cs5536: forward port changes from cs5536
libata-sff: use ATAPI_{COD|IO}
ata: add ata port runtime PM callbacks
ata: add ata port system PM callbacks
[SCSI] sd: check runtime PM status in sd_shutdown
[SCSI] check runtime PM status in system PM
[SCSI] add flag to skip the runtime PM calls on the host
ata: make ata port as parent device of scsi host
ahci: start engine only during soft/hard resets
Linus Torvalds [Tue, 10 Jan 2012 18:09:59 +0000 (10:09 -0800)]
Merge branch 'stable/for-linus-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
* 'stable/for-linus-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: (37 commits)
xen/pciback: Expand the warning message to include domain id.
xen/pciback: Fix "device has been assigned to X domain!" warning
xen/pciback: Move the PCI_DEV_FLAGS_ASSIGNED ops to the "[un|]bind"
xen/xenbus: don't reimplement kvasprintf via a fixed size buffer
xenbus: maximum buffer size is XENSTORE_PAYLOAD_MAX
xen/xenbus: Reject replies with payload > XENSTORE_PAYLOAD_MAX.
Xen: consolidate and simplify struct xenbus_driver instantiation
xen-gntalloc: introduce missing kfree
xen/xenbus: Fix compile error - missing header for xen_initial_domain()
xen/netback: Enable netback on HVM guests
xen/grant-table: Support mappings required by blkback
xenbus: Use grant-table wrapper functions
xenbus: Support HVM backends
xen/xenbus-frontend: Fix compile error with randconfig
xen/xenbus-frontend: Make error message more clear
xen/privcmd: Remove unused support for arch specific privcmp mmap
xen: Add xenbus_backend device
xen: Add xenbus device driver
xen: Add privcmd device driver
xen/gntalloc: fix reference counts on multi-page mappings
...
Linus Torvalds [Tue, 10 Jan 2012 17:57:11 +0000 (09:57 -0800)]
Merge branch 'kvm-updates/3.3' of git://git.kernel.org/pub/scm/virt/kvm/kvm
* 'kvm-updates/3.3' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (74 commits)
KVM: PPC: Whitespace fix for kvm.h
KVM: Fix whitespace in kvm_para.h
KVM: PPC: annotate kvm_rma_init as __init
KVM: x86 emulator: implement RDPMC (0F 33)
KVM: x86 emulator: fix RDPMC privilege check
KVM: Expose the architectural performance monitoring CPUID leaf
KVM: VMX: Intercept RDPMC
KVM: SVM: Intercept RDPMC
KVM: Add generic RDPMC support
KVM: Expose a version 2 architectural PMU to a guests
KVM: Expose kvm_lapic_local_deliver()
KVM: x86 emulator: Use opcode::execute for Group 9 instruction
KVM: x86 emulator: Use opcode::execute for Group 4/5 instructions
KVM: x86 emulator: Use opcode::execute for Group 1A instruction
KVM: ensure that debugfs entries have been created
KVM: drop bsp_vcpu pointer from kvm struct
KVM: x86: Consolidate PIT legacy test
KVM: x86: Do not rely on implicit inclusions
KVM: Make KVM_INTEL depend on CPU_SUP_INTEL
KVM: Use memdup_user instead of kmalloc/copy_from_user
...
Dan Carpenter [Wed, 4 Jan 2012 07:26:10 +0000 (10:26 +0300)]
gma500: silence gcc warnings in mid_get_vbt_data()
Add a cast here to silence a Gcc warning.
drivers/gpu/drm/gma500/mid_bios.c:214:28: warning:
cast from pointer to integer of different size [-Wpointer-to-int-cast]
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dan Carpenter [Thu, 8 Dec 2011 06:50:54 +0000 (09:50 +0300)]
drm/ttm: fix condition (and vs or)
The "if (!p && !p->dev)" condition isn't right because || was intended
instead of &&. But actually, "p" is the list cursor and so it's always
non-NULL and we can just remove that bit. We can remove the another
similar check as well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Jerome Glisse <jglisse@redhat.com> Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Linus Torvalds [Tue, 10 Jan 2012 01:37:37 +0000 (17:37 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vfs: new helper - d_make_root()
dcache: use a dispose list in select_parent
ceph: d_alloc_root() may fail
ext4: fix failure exits
isofs: inode leak on mount failure
Dave Chinner [Tue, 23 Aug 2011 08:56:24 +0000 (18:56 +1000)]
dcache: use a dispose list in select_parent
select_parent currently abuses the dentry cache LRU to provide
cleanup features for child dentries that need to be freed. It moves
them to the tail of the LRU, then tells shrink_dcache_parent() to
calls __shrink_dcache_sb to unconditionally move them to a dispose
list (as DCACHE_REFERENCED is ignored). __shrink_dcache_sb() has to
relock the dentries to move them off the LRU onto the dispose list,
but otherwise does not touch the dentries that select_parent() moved
to the tail of the LRU. It then passses the dispose list to
shrink_dentry_list() which tries to free the dentries.
IOWs, the use of __shrink_dcache_sb() is superfluous - we can build
exactly the same list of dentries for disposal directly in
select_parent() and call shrink_dentry_list() instead of calling
__shrink_dcache_sb() to do that. This means that we avoid long holds
on the lru lock walking the LRU moving dentries to the dispose list
We also avoid the need to relock each dentry just to move it off the
LRU, reducing the numebr of times we lock each dentry to dispose of
them in shrink_dcache_parent() from 3 to 2 times.
Further, we remove one of the two callers of __shrink_dcache_sb().
This also means that __shrink_dcache_sb can be moved into back into
prune_dcache_sb() and we no longer have to handle referenced
dentries conditionally, simplifying the code.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
igmp: Avoid zero delay when receiving odd mixture of IGMP queries
netdev: make net_device_ops const
bcm63xx: make ethtool_ops const
usbnet: make ethtool_ops const
net: Fix build with INET disabled.
net: introduce netif_addr_lock_nested() and call if when appropriate
net: correct lock name in dev_[uc/mc]_sync documentations.
net: sk_update_clone is only used in net/core/sock.c
8139cp: fix missing napi_gro_flush.
pktgen: set correct max and min in pktgen_setup_inject()
smsc911x: Unconditionally include linux/smscphy.h in smsc911x.h
asix: fix infinite loop in rx_fixup()
net: Default UDP and UNIX diag to 'n'.
r6040: fix typo in use of MCR0 register bits
net: fix sock_clone reference mismatch with tcp memcontrol
Linus Torvalds [Mon, 9 Jan 2012 22:44:15 +0000 (14:44 -0800)]
Merge tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
clock management changes for i.MX
Another simple series related to clock management, this time only for
imx.
* tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: mxs: select HAVE_CLK_PREPARE for clock
clk: add config option HAVE_CLK_PREPARE into Kconfig
ASoC: mxs-saif: convert to clk_prepare/clk_unprepare
video: mxsfb: convert to clk_prepare/clk_unprepare
serial: mxs-auart: convert to clk_prepare/clk_unprepare
net: flexcan: convert to clk_prepare/clk_unprepare
mtd: gpmi-lib: convert to clk_prepare/clk_unprepare
mmc: mxs-mmc: convert to clk_prepare/clk_unprepare
dma: mxs-dma: convert to clk_prepare/clk_unprepare
net: fec: add clk_prepare/clk_unprepare
ARM: mxs: convert platform code to clk_prepare/clk_unprepare
clk: add helper functions clk_prepare_enable and clk_disable_unprepare
Fix up trivial conflicts in drivers/net/ethernet/freescale/fec.c due to
commit 0ebafefcaa7a ("net: fec: add clk_prepare/clk_unprepare") clashing
trivially with commit e163cc97f9ac ("net/fec: fix the .remove code").
Linus Torvalds [Mon, 9 Jan 2012 22:40:48 +0000 (14:40 -0800)]
Merge tag 'timer' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
timer changes for msm
A very simple series. We used to have more churn in the timer
area, so this is kept separate. Will probably put this into the
drivers series next time.
* tag 'timer' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
msm: timer: Use clockevents_config_and_register()
msm: timer: Setup interrupt after registering clockevent
msm: timer: Remove SoC specific #ifdefs
msm: timer: Remove msm_clocks[] and simplify code
msm: timer: Fix ONESHOT mode interrupts
msm: timer: Use GPT for clockevents and DGT for clocksource
msm: timer: Cleanup #includes and #defines
msm: timer: Tighten #ifdef for local timer support
Linus Torvalds [Mon, 9 Jan 2012 22:39:59 +0000 (14:39 -0800)]
Merge tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
power management changes for omap and imx
A significant part of the changes for these two platforms went into
power management, so they are split out into a separate branch.
* tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (65 commits)
ARM: imx6: remove __CPUINIT annotation from v7_invalidate_l1
ARM: imx6: fix v7_invalidate_l1 by adding I-Cache invalidation
ARM: imx6q: resume PL310 only when CACHE_L2X0 defined
ARM: imx6q: build pm code only when CONFIG_PM selected
ARM: mx5: use generic irq chip pm interface for pm functions on
ARM: omap: pass minimal SoC/board data for UART from dt
arm/dts: Add minimal device tree support for omap2420 and omap2430
omap-serial: Add minimal device tree support
omap-serial: Use default clock speed (48Mhz) if not specified
omap-serial: Get rid of all pdev->id usage
ARM: OMAP2+: hwmod: Add a new flag to handle hwmods left enabled at init
ARM: OMAP4: PRM: use PRCM interrupt handler
ARM: OMAP3: pm: use prcm chain handler
ARM: OMAP: hwmod: add support for selecting mpu_irq for each wakeup pad
ARM: OMAP2+: mux: add support for PAD wakeup interrupts
ARM: OMAP: PRCM: add suspend prepare / finish support
ARM: OMAP: PRCM: add support for chain interrupt handler
ARM: OMAP3/4: PRM: add functions to read pending IRQs, PRM barrier
ARM: OMAP2+: hwmod: Add API to enable IO ring wakeup
ARM: OMAP2+: mux: add wakeup-capable hwmod mux entries to dynamic list
...
Linus Torvalds [Mon, 9 Jan 2012 22:39:22 +0000 (14:39 -0800)]
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Driver specific changes
Again, a lot of platforms have changes in here: pxa, samsung, omap,
at91, imx, ...
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
ARM: sa1100: clean up of the clock support
ARM: pxa: add dummy clock for sa1100-rtc
RTC: sa1100: support sa1100, pxa and mmp soc families
RTC: sa1100: remove redundant code of setting alarm
RTC: sa1100: Clean out ost register
Input: zylonite-wm97xx - replace IRQ_GPIO() with gpio_to_irq()
pcmcia: pxa: replace IRQ_GPIO() with gpio_to_irq()
ARM: EXYNOS: Modified files for SPI consolidation work
ARM: S5P64X0: Enable SDHCI support
ARM: S5P64X0: Add lookup of sdhci-s3c clocks using generic names
ARM: S5P64X0: Add HSMMC setup for host Controller
ARM: EXYNOS: Add USB OHCI support to ORIGEN board
USB: Add Samsung Exynos OHCI diver
ARM: EXYNOS: Add USB OHCI support to SMDKV310 board
ARM: EXYNOS: Add USB OHCI device
net: macb: fix build break with !CONFIG_OF
i2c: tegra: Support DVC controller in device tree
i2c: tegra: Add __devinit/exit to probe/remove
net/at91_ether: use gpio_is_valid for phy IRQ line
ARM: at91/net: add macb ethernet controller in 9g45/9g20 DT
...
Linus Torvalds [Mon, 9 Jan 2012 22:38:51 +0000 (14:38 -0800)]
Merge tag 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
New feature development
This adds support for new features, and contains stuff from most
platforms. A number of these patches could have fit into other
branches, too, but were small enough not to cause too much
confusion here.
* tag 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
mfd/db8500-prcmu: remove support for early silicon revisions
ARM: ux500: fix the smp_twd clock calculation
ARM: ux500: remove support for early silicon revisions
ARM: ux500: update register files
ARM: ux500: register DB5500 PMU dynamically
ARM: ux500: update ASIC detection for U5500
ARM: ux500: support DB8520
ARM: picoxcell: implement watchdog restart
ARM: OMAP3+: hwmod data: Add the default clockactivity for I2C
ARM: OMAP3: hwmod data: disable multiblock reads on MMC1/2 on OMAP34xx/35xx <= ES2.1
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP4
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP3
ARM: OMAP: hwmod data: Add support for AM35xx UART4/ttyO3
ARM: Orion: Remove address map info from all platform data structures
ARM: Orion: Get address map from plat-orion instead of via platform_data
ARM: Orion: mbus_dram_info consolidation
ARM: Orion: Consolidate the address map setup
ARM: Kirkwood: Add configuration for MPP12 as GPIO
ARM: Kirkwood: Recognize A1 revision of 6282 chip
ARM: ux500: update the MOP500 GPIO assignments
...
Linus Torvalds [Mon, 9 Jan 2012 22:37:41 +0000 (14:37 -0800)]
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Board-level changes
This adds and extends support for specific boards on a number of
ARM platforms: omap, imx, samsung, tegra, ...
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (49 commits)
Enable 32 bit flash support for iMX21ADS board
ARM: mx31pdk: Add MC13783 RTC support
iomux-mx25: configuration to support CSPI3 on CSI pins
MX1:apf9328: Add i2c support
mioa701: add newly available DoC G3 chip
arm/tegra: remove __initdata annotation from pinmux tables
arm/tegra: Use bus notifiers to trigger pinmux setup
arm/tegra: Refactor board-*-pinmux.c to share code
arm/tegra: Fix mistake in Trimslice's pinmux
arm/tegra: Rework Seaboard-vs-Ventana pinmux table
arm/tegra: Remove useless entries from ventana_pinmux[]
arm/tegra: PCIe: Remove include of mach/pinmux.h
arm/tegra: Harmony PCIe: Don't touch pinmux
arm/tegra: Add AUXDATA for tegra-pinmux and tegra-gpio
arm/tegra: Split Seaboard GPIO table to allow for Ventana
ARM: imx6q: generate imx6q dtb files
arm/imx6q: Rename Sabreauto to Armadillo2
arm/imx6q-sabrelite: add enet phy ksz9021rn fixup
arm/imx6: add imx6q sabrelite board support
dts/imx: rename uart labels to consistent with hw spec
...
Linus Torvalds [Mon, 9 Jan 2012 22:33:17 +0000 (14:33 -0800)]
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
SoC-level changes for tegra and omap
This adds support for the new tegra30 SoC, as well as small
changes to support minor variations of existing omap SoCs.
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
arm/tegra: Compile tegra_dt_init_irq only when CONFIG_OF
arm/tegra: Make MACH_TEGRA_DT depend on ARCH_TEGRA_2x_SOC
arm/tegra: Delete tegra_init_clock()
arm/tegra: Fix section mismatch errors in tegra30 pinmux
arm/tegra: Fix section mismatch errors in tegra20 pinmux
arm/tegra: refresh defconfig for tegra30
arm/tegra: add support for tegra30 based board cardhu
arm/tegra: implement support for tegra30
arm/tegra: pinmux tables and definitions for tegra30
arm/tegra: add new fields to struct tegra_pingroup_desc
arm/tegra: prepare pinmux code for multiple tegra variants
arm/tegra: rename tegra20 pinmux files
arm/tegra: generalize L2 cache initialization
arm/tegra: use PMC reset
arm/tegra: rename board-dt.c to board-dt-tegra20.c
arm/tegra: prepare early init for multiple tegra variants
arm/tegra: don't export clk_measure_input_freq
arm/tegra: prepare clock code for multiple tegra variants
arm/tegra: cleanup tegra20 support
arm/tegra: clk_get should not be fatal
...
Fix up trivial conflict in arch/arm/mach-tegra/board-dt-tegra20.c
Linus Torvalds [Mon, 9 Jan 2012 22:30:28 +0000 (14:30 -0800)]
Merge tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Cleanups for the Samsung platforms
Various cleanup changes that the device driver changes are built upon.
Since the samsung cleanups depend on the device tree series, which
depends on the first set of cleanups for tegra.
* tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: EXYNOS: Use gpio_request_one
ARM: S5PV210: Use gpio_request_one
ARM: S3C64XX: Modified according to SPI consolidation work
ARM: S5PV210: Modified files for SPI consolidation work
ARM: S5P64X0: Modified files for SPI consolidation work
ARM: S5PC100: Modified files for SPI consolidation work
ARM: S3C64XX: Modified files for SPI consolidation work
ARM: SAMSUNG: Consolidation of SPI platform devices to plat-samsung
ARM: SAMSUNG: Remove SPI bus clocks from platform data
ARM: S5PV210: Add SPI clkdev support
ARM: S5P64X0: Add SPI clkdev support
ARM: S5PC100: Add SPI clkdev support
ARM: S3C64XX: Add SPI clkdev support
spi/s3c64xx: Use bus clocks created using clkdev
mmc: sdhci-s3c: Use generic clock names for sdhci bus clock options
ARM: SAMSUNG: Add lookup of sdhci-s3c clocks using generic names
ARM: SAMSUNG: Remove SDHCI bus clocks from platform data
ARM: SAMSUNG: Use kmemdup rather than duplicating its implementation
ARM: EXYNOS: remove exynos4_scu_enable()
Linus Torvalds [Mon, 9 Jan 2012 22:28:38 +0000 (14:28 -0800)]
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Device tree conversions for samsung and tegra
Both platforms had some initial device tree support, but this adds
much more to actually make it usable.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
ARM: dts: Add intial dts file for EXYNOS4210 SoC, SMDKV310 and ORIGEN
ARM: EXYNOS: Add Exynos4 device tree enabled board file
rtc: rtc-s3c: Add device tree support
input: samsung-keypad: Add device tree support
ARM: S5PV210: Modify platform data for pl330 driver
ARM: S5PC100: Modify platform data for pl330 driver
ARM: S5P64x0: Modify platform data for pl330 driver
ARM: EXYNOS: Add a alias for pdma clocks
ARM: EXYNOS: Limit usage of pl330 device instance to non-dt build
ARM: SAMSUNG: Add device tree support for pl330 dma engine wrappers
DMA: PL330: Add device tree support
ARM: EXYNOS: Modify platform data for pl330 driver
DMA: PL330: Infer transfer direction from transfer request instead of platform data
DMA: PL330: move filter function into driver
serial: samsung: Fix build for non-Exynos4210 devices
serial: samsung: add device tree support
serial: samsung: merge probe() function from all SoC specific extensions
serial: samsung: merge all SoC specific port reset functions
ARM: SAMSUNG: register uart clocks to clock lookup list
serial: samsung: remove all uses of get_clksrc and set_clksrc
...
Fix up fairly trivial conflicts in arch/arm/mach-s3c2440/clock.c and
drivers/tty/serial/Kconfig both due to just adding code close to
changes.
Linus Torvalds [Mon, 9 Jan 2012 22:21:03 +0000 (14:21 -0800)]
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Cleanups on various subarchitectures
Cleanup patches for various ARM platforms and some of their associated
drivers, the bulk of these is for mach-91.
Arnd ended up pulling in the restart branch from Russell in order to
fix up some simple but annoying merge conflicts.
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
arm/at91: fix build of stamp9g20
ARM: u300: delete memory.h
MAINTAINERS: add maintainer entry for Picochip picoxcell
ARM: picoxcell: move io mappings to common.c
ARM: picoxcell: don't reserve irq_descs
ARM: picoxcell: remove mach/memory.h
ARM: at91: delete the pcontrol_g20_defconfig
arm/tegra: Remove code that's ifndef CONFIG_ARM_GIC
arm/tegra: remove unused defines
arm/tegra: fix variable formatting in makefile
ARM: davinci: vpif: move code to driver core header from platform
ARM: at91/gpio: fix display of number of irq setuped
ARM: at91/gpio: drop PIN_BASE
ARM: at91/udc: use gpio_is_valid to check the gpio
ARM: at91/ohci: use gpio_is_valid to check the gpio
ARM: at91/nand: use gpio_is_valid to check the gpio
ARM: at91/mmc: use gpio_is_valid to check the gpio
ARM: at91/ide: use gpio_is_valid to check the gpio
ARM: at91/pata: use gpio_is_valid to check the gpio
ARM: at91/soc: use gpio_is_valid to check the gpio
...
Linus Torvalds [Mon, 9 Jan 2012 22:20:39 +0000 (14:20 -0800)]
Merge tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Non-critical bug fixes
Simple bug fixes that were not considered important enough for inclusion
into 3.2.
* tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: update pxa and mmp
ARM: pxa: Include linux/export.h in balloon3.c
ARM: OMAP4: clock: Add CPU local timer clock node
ARM: OMAP4: hwmod: Don't wait for the idle status if modulemode is not supported
ARM: OMAP: AM3517/3505: fix crash on boot due to incorrect voltagedomain data
ARM: OMAP: hwmod data: fix the panic on Nokia RM-680 during boot
ARM: OMAP2+: DMA: Workaround for invalid destination position
ARM: OMAP2+: DMA: Workaround for invalid source position
Steven Rostedt [Mon, 9 Jan 2012 22:15:42 +0000 (17:15 -0500)]
tracing/mm: Move include of trace/events/kmem.h out of header into slab.c
Including trace/events/*.h TRACE_EVENT() macro headers in other headers
can cause strange side effects if another trace/event/*.h header
includes that header. Having trace/events/kmem.h inside slab_def.h
caused a compile error in sparc64 when changes were done to some header
files. Moving the kmem.h trace header out of slab.h and into slab.c
fixes the problem.
Note, both slub.c and slob.c already include the trace/events/kmem.h
file. Only slab.c had it missing.
Ben Hutchings [Mon, 9 Jan 2012 22:06:46 +0000 (14:06 -0800)]
igmp: Avoid zero delay when receiving odd mixture of IGMP queries
Commit 5b7c84066733c5dfb0e4016d939757b38de189e4 ('ipv4: correct IGMP
behavior on v3 query during v2-compatibility mode') added yet another
case for query parsing, which can result in max_delay = 0. Substitute
a value of 1, as in the usual v3 case.
Reported-by: Simon McVittie <smcv@debian.org>
References: http://bugs.debian.org/654876 Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 9 Jan 2012 21:08:28 +0000 (13:08 -0800)]
Merge branch 'for-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu
* 'for-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: Remove irqsafe_cpu_xxx variants
Fix up conflict in arch/x86/include/asm/percpu.h due to clash with cebef5beed3d ("x86: Fix and improve percpu_cmpxchg{8,16}b_double()")
which edited the (now removed) irqsafe_cpu_cmpxchg*_double code.
Linus Torvalds [Mon, 9 Jan 2012 20:59:24 +0000 (12:59 -0800)]
Merge branch 'for-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
* 'for-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (21 commits)
cgroup: fix to allow mounting a hierarchy by name
cgroup: move assignement out of condition in cgroup_attach_proc()
cgroup: Remove task_lock() from cgroup_post_fork()
cgroup: add sparse annotation to cgroup_iter_start() and cgroup_iter_end()
cgroup: mark cgroup_rmdir_waitq and cgroup_attach_proc() as static
cgroup: only need to check oldcgrp==newgrp once
cgroup: remove redundant get/put of task struct
cgroup: remove redundant get/put of old css_set from migrate
cgroup: Remove unnecessary task_lock before fetching css_set on migration
cgroup: Drop task_lock(parent) on cgroup_fork()
cgroups: remove redundant get/put of css_set from css_set_check_fetched()
resource cgroups: remove bogus cast
cgroup: kill subsys->can_attach_task(), pre_attach() and attach_task()
cgroup, cpuset: don't use ss->pre_attach()
cgroup: don't use subsys->can_attach_task() or ->attach_task()
cgroup: introduce cgroup_taskset and use it in subsys->can_attach(), cancel_attach() and attach()
cgroup: improve old cgroup handling in cgroup_attach_proc()
cgroup: always lock threadgroup during migration
threadgroup: extend threadgroup_lock() to cover exit and exec
threadgroup: rename signal->threadgroup_fork_lock to ->group_rwsem
...
Fix up conflict in kernel/cgroup.c due to commit e0197aae59e5: "cgroups:
fix a css_set not found bug in cgroup_attach_proc" that already
mentioned that the bug is fixed (differently) in Tejun's cgroup
patchset. This one, in other words.
Al Viro [Mon, 9 Jan 2012 20:53:24 +0000 (15:53 -0500)]
ext4: fix failure exits
a) leaking root dentry is bad
b) in case of failed ext4_mb_init() we don't want to do ext4_mb_release()
c) OTOH, in the same case we *do* want ext4_ext_release()
Linus Torvalds [Mon, 9 Jan 2012 20:51:21 +0000 (12:51 -0800)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
ext2/3/4: delete unneeded includes of module.h
ext{3,4}: Fix potential race when setversion ioctl updates inode
udf: Mark LVID buffer as uptodate before marking it dirty
ext3: Don't warn from writepage when readonly inode is spotted after error
jbd: Remove j_barrier mutex
reiserfs: Force inode evictions before umount to avoid crash
reiserfs: Fix quota mount option parsing
udf: Treat symlink component of type 2 as /
udf: Fix deadlock when converting file from in-ICB one to normal one
udf: Cleanup calling convention of inode_getblk()
ext2: Fix error handling on inode bitmap corruption
ext3: Fix error handling on inode bitmap corruption
ext3: replace ll_rw_block with other functions
ext3: NULL dereference in ext3_evict_inode()
jbd: clear revoked flag on buffers before a new transaction started
ext3: call ext3_mark_recovery_complete() when recovery is really needed
Linus Torvalds [Mon, 9 Jan 2012 20:51:01 +0000 (12:51 -0800)]
Merge branch 'for-linus' of git://git.open-osd.org/linux-open-osd
* 'for-linus' of git://git.open-osd.org/linux-open-osd:
ore: Must support none-PAGE-aligned IO
ore: fix BUG_ON, too few sgs when reading
ore: Fix crash in case of an IO error.
ore: FIX breakage when MISC_FILESYSTEMS is not set
Jiri Pirko [Mon, 9 Jan 2012 06:36:54 +0000 (06:36 +0000)]
net: introduce netif_addr_lock_nested() and call if when appropriate
dev_uc_sync() and dev_mc_sync() are acquiring netif_addr_lock for
destination device of synchronization. Since netif_addr_lock is
already held at the time for source device, this triggers lockdep
deadlock warning.
There's no way this deadlock can happen so use spin_lock_nested() to
silence the warning.
Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 9 Jan 2012 20:18:17 +0000 (12:18 -0800)]
Merge branch 'staging-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
* 'staging-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (466 commits)
net/hyperv: Add support for jumbo frame up to 64KB
net/hyperv: Add NETVSP protocol version negotiation
net/hyperv: Remove unnecessary kmap_atomic in netvsc driver
staging/rtl8192e: Register against lib80211
staging/rtl8192e: Convert to lib80211_crypt_info
staging/rtl8192e: Convert to lib80211_crypt_data and lib80211_crypt_ops
staging/rtl8192e: Add lib80211.h to rtllib.h
staging/mei: add watchdog device registration wrappers
drm/omap: GEM, deal with cache
staging: vt6656: int.c, int.h: Change return of function to void
staging: usbip: removed unused definitions from header
staging: usbip: removed dead code from receive function
staging:iio: Drop {mark,unmark}_in_use callbacks
staging:iio: Drop buffer mark_param_change callback
staging:iio: Drop the unused buffer enable() and is_enabled() callbacks
staging:iio: Drop buffer busy flag
staging:iio: Make sure a device is only opened once at a time
staging:iio: Disallow modifying buffer size when buffer is enabled
staging:iio: Disallow changing scan elements in all buffered modes
staging:iio: Use iio_buffer_enabled instead of open coding it
...
Fix up conflict in drivers/staging/iio/adc/ad799x_core.c (removal of
module_init due to using module_i2c_driver() helper, next to removal of
MODULE_ALIAS due to using MODULE_DEVICE_TABLE instead).
Linus Torvalds [Mon, 9 Jan 2012 20:09:24 +0000 (12:09 -0800)]
Merge branch 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (65 commits)
tty: serial: imx: move del_timer_sync() to avoid potential deadlock
imx: add polled io uart methods
imx: Add save/restore functions for UART control regs
serial/imx: let probing fail for the dt case without a valid alias
serial/imx: propagate error from of_alias_get_id instead of using -ENODEV
tty: serial: imx: Allow UART to be a source for wakeup
serial: driver for m32 arch should not have DEC alpha errata
serial/documentation: fix documented name of DCD cpp symbol
atmel_serial: fix spinlock lockup in RS485 code
tty: Fix memory leak in virtual console when enable unicode translation
serial: use DIV_ROUND_CLOSEST instead of open coding it
serial: add support for 400 and 800 v3 series Titan cards
serial: bfin-uart: Remove ASYNC_CTS_FLOW flag for hardware automatic CTS.
serial: bfin-uart: Enable hardware automatic CTS only when CTS pin is available.
serial: make FSL errata depend on 8250_CONSOLE, not just 8250
serial: add irq handler for Freescale 16550 errata.
serial: manually inline serial8250_handle_port
serial: make 8250 timeout use the specified IRQ handler
serial: export the key functions for an 8250 IRQ handler
serial: clean up parameter passing for 8250 Rx IRQ handling
...
Lots of relatively simple conflicts between the board
changes and stuff from the arm tree. This pulls in
the resolution from the samsung/cleanup tree, so we
don't get conflicting merges.
arch/x86/xen/mmu.c: In function ‘xen_setup_kernel_pagetable’:
arch/x86/xen/mmu.c:1855: error: expected ‘;’ before ‘)’ token
arch/x86/xen/mmu.c:1855: error: expected statement before ‘)’ token
Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Linus Torvalds [Mon, 9 Jan 2012 16:31:22 +0000 (08:31 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ext[34]: avoid i_nlink warnings triggered by drop_nlink/inc_nlink kludge in symlink()
exofs: oops after late failure in mount
devpts: fix double-free on mount failure
... and the same for gadgetfs
functionfs: unfuck failure exits on mount
Linus Torvalds [Mon, 9 Jan 2012 16:11:13 +0000 (08:11 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (31 commits)
[S390] disassembler: mark exception causing instructions
[S390] Enable exception traces by default
[S390] return address of compat signals
[S390] sysctl: get rid of dead declaration
[S390] dasd: fix fixpoint divide exception in define_extent
[S390] dasd: add sanity check to detect path connection error
[S390] qdio: fix kernel panic for zfcp 31-bit
[S390] Add s390x description to Documentation/kdump/kdump.txt
[S390] Add VMCOREINFO_SYMBOL(high_memory) to vmcoreinfo
[S390] dasd: fix expiration handling for recovery requests
[S390] outstanding interrupts vs. smp_send_stop
[S390] ipc: call generic sys_ipc demultiplexer
[S390] zcrypt: Fix error return codes.
[S390] zcrypt: Rework length parameter checking.
[S390] cleanup trap handling
[S390] Remove Kerntypes leftovers
[S390] topology: increase poll frequency if change is anticipated
[S390] entry[64].S improvements
[S390] make arch/s390 subdirectories depend on config option
[S390] kvm: move cmf host id constant out of lowcore
...
Fix up conflicts in arch/s390/kernel/{smp.c,topology.c} due to the
sysdev removal clashing with "topology: get rid of ifdefs" which moved
some of that code around.
The Makefiles were reorganized in the "rmk/restart" series and modified
in the "samsung/cleanup series". This also pulls in the other conflict
resolutions from the restart series against the samsung/dt series.
xen/pciback: Expand the warning message to include domain id.
When a PCI device is transferred to another domain and it is still
in usage (from the internal perspective), mention which other
domain is using it to aid in debugging.
[v2: Truncate the verbose message per Jan Beulich suggestion]
[v3: Suggestions from Ian Campbell on the wording] Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Acked-by: Jan Beulich <jbeulich@suse.com>
Paul Gortmaker [Wed, 4 Jan 2012 20:59:47 +0000 (15:59 -0500)]
ext2/3/4: delete unneeded includes of module.h
Delete any instances of include module.h that were not strictly
required. In the case of ext2, the declaration of MODULE_LICENSE
etc. were in inode.c but the module_init/exit were in super.c, so
relocate the MODULE_LICENCE/AUTHOR block to super.c which makes it
consistent with ext3 and ext4 at the same time.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Jan Kara <jack@suse.cz>
Djalal Harouni [Tue, 3 Jan 2012 01:31:52 +0000 (02:31 +0100)]
ext{3,4}: Fix potential race when setversion ioctl updates inode
The EXT{3,4}_IOC_SETVERSION ioctl() updates i_ctime and i_generation
without i_mutex. This can lead to a race with the other operations that
update i_ctime. This is not a big issue but let's make the ioctl consistent
with how we handle e.g. other timestamp updates and use i_mutex to protect
inode changes.
Signed-off-by: Djalal Harouni <tixxdz@opendz.org> Signed-off-by: Jan Kara <jack@suse.cz>
Jan Kara [Fri, 23 Dec 2011 10:53:07 +0000 (11:53 +0100)]
udf: Mark LVID buffer as uptodate before marking it dirty
When we hit EIO while writing LVID, the buffer uptodate bit is cleared.
This then results in an anoying warning from mark_buffer_dirty() when we
write the buffer again. So just set uptodate flag unconditionally.
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com> Signed-off-by: Jan Kara <jack@suse.cz>
Jan Kara [Thu, 22 Dec 2011 15:49:05 +0000 (16:49 +0100)]
ext3: Don't warn from writepage when readonly inode is spotted after error
WARN_ON_ONCE(IS_RDONLY(inode)) tends to trip when filesystem hits error and is
remounted read-only. This unnecessarily scares users (well, they should be
scared because of filesystem error, but the stack trace distracts them from the
right source of their fear ;-). We could as well just remove the WARN_ON but
it's not hard to fix it to not trip on filesystem with errors and not use more
cycles in the common case so that's what we do.
CC: stable@kernel.org Signed-off-by: Jan Kara <jack@suse.cz>
Jan Kara [Thu, 22 Dec 2011 13:52:21 +0000 (14:52 +0100)]
jbd: Remove j_barrier mutex
j_barrier mutex is used for serializing different journal lock operations. The
problem with it is that e.g. FIFREEZE ioctl results in process leaving kernel
with j_barrier mutex held which makes lockdep freak out. Also hibernation code
wants to freeze filesystem but it cannot do so because it then cannot hibernate
the system because of mutex being locked.
So we remove j_barrier mutex and use direct wait on j_barrier_count instead.
Since locking journal is a rare operation we don't have to care about fairness
or such things.
CC: Andrew Morton <akpm@linux-foundation.org> Acked-by: Joel Becker <jlbec@evilplan.org> Signed-off-by: Jan Kara <jack@suse.cz>
Jeff Mahoney [Wed, 21 Dec 2011 20:18:43 +0000 (21:18 +0100)]
reiserfs: Force inode evictions before umount to avoid crash
This patch fixes a crash in reiserfs_delete_xattrs during umount.
When shrink_dcache_for_umount clears the dcache from
generic_shutdown_super, delayed evictions are forced to disk. If an
evicted inode has extended attributes associated with it, it will
need to walk the xattr tree to locate and remove them.
But since shrink_dcache_for_umount will BUG if it encounters active
dentries, the xattr tree must be released before it's called or it will
crash during every umount.
This patch forces the evictions to occur before generic_shutdown_super
by calling shrink_dcache_sb first. The additional evictions caused
by the removal of each associated xattr file and dir will be automatically
handled as they're added to the LRU list.
CC: reiserfs-devel@vger.kernel.org CC: stable@kernel.org Signed-off-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Jan Kara <jack@suse.cz>
Jan Kara [Sat, 10 Dec 2011 01:30:48 +0000 (02:30 +0100)]
udf: Fix deadlock when converting file from in-ICB one to normal one
During BKL removal in 2.6.38, conversion of files from in-ICB format to normal
format got broken. We call ->writepage with i_data_sem held but udf_get_block()
also acquires i_data_sem thus creating A-A deadlock.
We fix the problem by dropping i_data_sem before calling ->writepage() which is
safe since i_mutex still protects us against any changes in the file. Also fix
pagelock - i_data_sem lock inversion in udf_expand_file_adinicb() by dropping
i_data_sem before calling find_or_create_page().
CC: stable@kernel.org Reported-by: Matthias Matiak <netzpython@mail-on.us> Tested-by: Matthias Matiak <netzpython@mail-on.us> Reviewed-by: Namjae Jeon <linkinjeon@gmail.com> Signed-off-by: Jan Kara <jack@suse.cz>
Jan Kara [Thu, 8 Dec 2011 23:08:58 +0000 (00:08 +0100)]
ext2: Fix error handling on inode bitmap corruption
When insert_inode_locked() fails in ext2_new_inode() it most likely means inode
bitmap got corrupted and we allocated again inode which is already in use. Also
doing unlock_new_inode() during error recovery is wrong since the inode does
not have I_NEW set. Fix the problem by informing about filesystem error and
jumping to fail: (instead of fail_drop:) which doesn't call unlock_new_inode().
Reviewed-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Jan Kara <jack@suse.cz>
Jan Kara [Thu, 8 Dec 2011 20:13:46 +0000 (21:13 +0100)]
ext3: Fix error handling on inode bitmap corruption
When insert_inode_locked() fails in ext3_new_inode() it most likely
means inode bitmap got corrupted and we allocated again inode which
is already in use. Also doing unlock_new_inode() during error recovery
is wrong since inode does not have I_NEW set. Fix the problem by jumping
to fail: (instead of fail_drop:) which declares filesystem error and
does not call unlock_new_inode().
Reviewed-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Jan Kara <jack@suse.cz>
Daniel Vetter [Sun, 8 Jan 2012 21:42:27 +0000 (22:42 +0100)]
drm/sis|via: don't return stack garbage from free_mem ioctl
Fallout from my "kill drm_sman" refactor. Unfortunately gcc seems to
have failed me and not warned about this.
Tested-by: Jakob Bornecrantz <wallbraker@gmail.com> (on via) Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
net: sk_update_clone is only used in net/core/sock.c
so move it there. Fixes build errors when CONFIG_INET is not defined:
In file included from include/linux/tcp.h:211:0,
from include/linux/ipv6.h:221,
from include/net/ipv6.h:16,
from include/linux/sunrpc/clnt.h:26,
from include/linux/nfs_fs.h:50,
from init/do_mounts.c:20:
include/net/sock.h: In function 'sk_update_clone':
include/net/sock.h:1109:3: error: implicit declaration of function 'sock_update_memcg' [-Werror=implicit-function-declaration]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log