2) ns_capable() check in sock_diag netlink code, from Andrew
Lutomirski.
3) Fix invalid queue pairs handling in virtio_net, from Amos Kong.
4) Checksum offloading busted in sxgbe driver due to incorrect
descriptor layout, fix from Byungho An.
5) Fix build failure with SMC_DEBUG set to 2 or larger, from Zi Shen
Lim.
6) Fix uninitialized A and X registers in BPF interpreter, from Alexei
Starovoitov.
7) Fix arch dependencies of candence driver.
8) Fix netlink capabilities checking tree-wide, from Eric W Biederman.
9) Don't dump IFLA_VF_PORTS if netlink request didn't ask for it in
IFLA_EXT_MASK, from David Gibson.
10) IPV6 FIB dump restart doesn't handle table changes that happen
meanwhile, causing the code to loop forever or emit dups, fix from
Kumar Sandararajan.
11) Memory leak on VF removal in bnx2x, from Yuval Mintz.
12) Bug fixes for new Altera TSE driver from Vince Bridgers.
13) Fix route lookup key in SCTP, from Xugeng Zhang.
14) Use BH blocking spinlocks in SLIP, as per a similar fix to CAN/SLCAN
driver. From Oliver Hartkopp.
15) TCP doesn't bump retransmit counters in some code paths, fix from
Eric Dumazet.
16) Clamp delayed_ack in tcp_cubic to prevent theoretical divides by
zero. Fix from Liu Yu.
17) Fix locking imbalance in error paths of HHF packet scheduler, from
John Fastabend.
18) Properly reference the transport module when vsock_core_init() runs,
from Andy King.
19) Fix buffer overflow in cdc_ncm driver, from Bjørn Mork.
20) IP_ECN_decapsulate() doesn't see a correct SKB network header in
ip_tunnel_rcv(), fix from Ying Cai.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (132 commits)
net: macb: Fix race between HW and driver
net: macb: Remove 'unlikely' optimization
net: macb: Re-enable RX interrupt only when RX is done
net: macb: Clear interrupt flags
net: macb: Pass same size to DMA_UNMAP as used for DMA_MAP
ip_tunnel: Set network header properly for IP_ECN_decapsulate()
e1000e: Restrict MDIO Slow Mode workaround to relevant parts
e1000e: Fix issue with link flap on 82579
e1000e: Expand workaround for 10Mb HD throughput bug
e1000e: Workaround for dropped packets in Gig/100 speeds on 82579
net/mlx4_core: Don't issue PCIe speed/width checks for VFs
net/mlx4_core: Load the Eth driver first
net/mlx4_core: Fix slave id computation for single port VF
net/mlx4_core: Adjust port number in qp_attach wrapper when detaching
net: cdc_ncm: fix buffer overflow
Altera TSE: ALTERA_TSE should depend on HAS_DMA
vsock: Make transport the proto owner
net: sched: lock imbalance in hhf qdisc
net: mvmdio: Check for a valid interrupt instead of an error
net phy: Check for aneg completion before setting state to PHY_RUNNING
...
Daniel Palmer [Sat, 5 Apr 2014 08:05:45 +0000 (17:05 +0900)]
m68k: fix a compiler warning when building for DragonBall
In file included from arch/m68k/kernel/setup.c:4:0:
arch/m68k/kernel/setup_no.c:70:0: warning: "CPU_NAME" redefined [enabled by default]
#define CPU_NAME "MC68VZ328"
^
arch/m68k/kernel/setup_no.c:61:0: note: this is the location of the previous definition
#define CPU_NAME "MC68000"
^
Signed-off-by: Daniel Palmer <danieruru@gmail.com> Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Linus Torvalds [Mon, 5 May 2014 22:51:17 +0000 (15:51 -0700)]
Merge tag 'usb-3.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small fixes and device ids for 3.15-rc4.
All have been in linux-next just fine"
* tag 'usb-3.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: Nokia 5300 should be treated as unusual dev
USB: Nokia 305 should be treated as unusual dev
fsl-usb: do not test for PHY_CLK_VALID bit on controller version 1.6
usb: storage: shuttle_usbat: fix discs being detected twice
usb: qcserial: add a number of Dell devices
USB: OHCI: fix problem with global suspend on ATI controllers
usb: gadget: at91-udc: fix irq and iomem resource retrieval
usb: phy: fsm: change "|" to "||" for condition OTG_STATE_A_WAIT_BCON at statemachine
usb: phy: fsm: update OTG HNP state transition
Linus Torvalds [Mon, 5 May 2014 22:50:16 +0000 (15:50 -0700)]
Merge tag 'tty-3.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some tty and serial driver fixes for things reported
recently"
* tag 'tty-3.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: Fix lockless tty buffer race
Revert "tty: Fix race condition between __tty_buffer_request_room and flush_to_ldisc"
drivers/tty/hvc: don't free hvc_console_setup after init
n_tty: Fix n_tty_write crash when echoing in raw mode
tty: serial: 8250_core.c Bug fix for Exar chips.
Linus Torvalds [Mon, 5 May 2014 22:49:38 +0000 (15:49 -0700)]
Merge tag 'staging-3.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging / iio fixes from Greg KH:
"Here are some small IIO driver fixes for 3.15-rc4 that resolve some
reported issues"
* tag 'staging-3.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio: adc: Nothing in ADC should be a bool CONFIG
iio: exynos_adc: use indio_dev->dev structure to handle child nodes
iio:imu:mpu6050: Fixed segfault in Invensens MPU driver due to null dereference
staging:iio:ad2s1200 fix missing parenthesis in a for statment.
Linus Torvalds [Mon, 5 May 2014 22:17:02 +0000 (15:17 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph fixes from Sage Weil:
"First, there is a critical fix for the new primary-affinity function
that went into -rc1.
The second batch of patches from Zheng fix a range of problems with
directory fragmentation, readdir, and a few odds and ends for cephfs"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: reserve caps for file layout/lock MDS requests
ceph: avoid releasing caps that are being used
ceph: clear directory's completeness when creating file
libceph: fix non-default values check in apply_primary_affinity()
ceph: use fpos_cmp() to compare dentry positions
ceph: check directory's completeness before emitting directory entry
Thomas Petazzoni [Mon, 14 Apr 2014 14:41:18 +0000 (16:41 +0200)]
ARM: configs: add CONFIG_MMC_SDHCI_PXAV3 to the multi_v7_defconfig
The Marvell Armada 38x platform has a SDHCI interface managed by the
sdhci-pxav3 MMC host driver. It therefore makes sense to enable this
driver in multi_v7_defconfig, which supports the Armada 38x platform.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Mon, 5 May 2014 21:33:48 +0000 (14:33 -0700)]
Merge tag 'renesas-dt-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Renesas ARM Based SoC DT Updates for v3.16" from Simon Horman:
r8a7791 (R-Car M2) and r8a7790 (R-Car H2) SoCs
* Add MSIOF nodes and aliases
* Correct I2C clock parents
r8a7791 (R-Car M2) SoC
* Add EHCI MSTP clock
r8a7791 (R-Car M2) based Koelsch and r8a7790 (R-Car H2) based Lager boards
* Add MSIOF nodes
* Add gpio-keys support for SW2
* Enable I2C
* Enable Quad SPI transfers for the SPI FLASH
* Rename and lable spi to qspi, add spi0 alias
* Set ethernet PHY LED mode
r8a7779 (R-Car H1) and r8a7778 (R-Car M2) SoCs
* Improve and correct HSPI nodes
r8a7778 (R-Car M2) based Bock-W board
* Add SPI FLASH
r8a7740 (R-Mobile A1) SoC
* Use r8a7740 suffix for i2c, mmcif, fsi2 compat strings
r8a7740 (R-Mobile A1) based Armadillo800 EVA board
* Enable RTC
* Use KEY_* macros for gpio-keys
EMEV2 (Emma Mobile EV2) based kzm9g board
* Use KEY_* macros for gpio-keys
* tag 'renesas-dt-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (33 commits)
ARM: shmobile: armadillo-reference dts: Seiko Instruments, Inc is "sii"
ARM: shmobile: lager dts: Enable Quad SPI transfers for the SPI FLASH
ARM: shmobile: koelsch dts: Enable Quad SPI transfers for the SPI FLASH
ARM: shmobile: r8a7790: add IIC(B) cores to dtsi
ARM: shmobile: r8a7790: add IIC(B) clocks to dtsi
ARM: shmobile: r8a7790: add IIC0-2 clock macros
ARM: shmobile: r8a7791: Fix the I2C clocks parents in DT
ARM: shmobile: r8a7790: Fix the I2C clocks parents in DT
ARM: shmobile: lager: Correct setting of ethernet PHY LED mode
ARM: shmobile: armadillo-reference dts: enable RTC
ARM: shmobile: r8a7791: Add EHCI MSTP clock
ARM: shmobile: Use r8a7740 suffix for i2c, mmcif, fsi2 compat strings
ARM: shmobile: koelsch: activate i2c6 bus
ARM: shmobile: koelsch: make i2c2-pfc node unique
ARM: shmobile: r8a7791: add IIC(B) cores to dtsi
ARM: shmobile: r8a7791: add IIC(B) clocks to dtsi
ARM: shmobile: r8a7791: add IIC0/1 clock macros
ARM: shmobile: kzm9g-reference dts: Use KEY_* macros for gpio-keys
ARM: shmobile: armadillo-reference dts: Use KEY_* macros for gpio-keys
ARM: shmobile: koelsch: Set ethernet PHY LED mode
...
Olof Johansson [Mon, 5 May 2014 21:19:55 +0000 (14:19 -0700)]
Merge branch 'next/boards' into for-next
* next/boards:
ARM: multi_v7_defconfig: Select CONFIG_MACH_BERLIN_BG2Q
ARM: multi_v7_defconfig: select CONFIG_GPIO_DWAPB
ARM: multi_v7: enable AT24C EEPROM driver
ARM: shmobile: lager legacy: Enable Quad SPI transfers for the SPI FLASH
ARM: shmobile: koelsch legacy: Enable Quad SPI transfers for the SPI FLASH
ARM: shmobile: lager: switch to use dai info for R-Car sound
ARM: shmobile: bockw: switch to use dai info for R-Car sound
ARM: shmobile: bockw: remove old style audio clock
ARM: shmobile: Add Koelsch clock workarounds for SDHI
ARM: shmobile: Add Lager clock workarounds for SDHI and MMCIF
ARM: shmobile: lager-reference: Work around core clock issues
ARM: shmobile: koelsch-reference: Annotate clk_enables as __initconst
ARM: shmobile: koelsch-reference: Work around core clock issues
ARM: shmobile: lager: Annotate clk_names with __initconst
ARM: shmobile: koelsch: Annotate clk_names with __initconst
ARM: shmobile: Use shmobile_clk_workaround() on Koelsch
ARM: shmobile: Use shmobile_clk_workaround() on Lager
Olof Johansson [Mon, 5 May 2014 21:15:54 +0000 (14:15 -0700)]
Merge tag 'at91-dt' of git://github.com/at91linux/linux-at91 into next/dt
Merge "at91: DT for 3.16 #1" from Nicolas Ferre:
3.16: first DT series:
- more support for at91sam9rl and its associated EK board
- some improvements to at91sam9g45 (ADC, TS, PWM leds)
- addition of some missing pieces for describing audio
of SAMA5D3-EK in DT
* tag 'at91-dt' of git://github.com/at91linux/linux-at91:
ARM: at91: sama5d3: clock for ssc from rk pin
ARM: at91: sama5d3: add the missing property
ARM: at91: sama5d3: correct the sound compatible string
ARM: at91: sama5d3: disable sound by default
ARM: at91: sama5d3: add DMA property for SSC devices
ARM: at91/dt: at91sam9m10g45ek PWM leds polarity is inversed
ARM: at91/dt: at91sam9m10g45ek: add ADC and touchscreen support
ARM: at91/dt: sam9g45: improve ADC/touchscreen support
ARM: at91/dt: add peripherals to the at91sam9rlek board
ARM: at91/dt: sam9rl: add lcd, adc, usb gadget and pwm support
Olof Johansson [Mon, 5 May 2014 21:14:29 +0000 (14:14 -0700)]
Merge tag 'renesas-boards-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/boards
Merge "Renesas ARM Based SoC Boards Updates for v3.16" from Simon Horman:
r8a7791 (R-Car M2) based Koelsch board
* Enable Quad SPI transfers for the SPI FLASH
* Clock workarounds for Ether, I2C, MSIOF, Quad SPI and SDHI
* Use shmobile_clk_workaround()
r8a7790 (R-Car H2) based Lager board
* Enable Quad SPI transfers for the SPI FLASH
* Switch to use dai info for R-Car sound
* Clock workarounds for Ether, MSIOF, MMCIF, Quad SPI and SDHI
* Use shmobile_clk_workaround()
r8a7778 (R-Car M1) based Bock-W board
* Switch to use dai info for R-Car sound
* tag 'renesas-boards-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: lager legacy: Enable Quad SPI transfers for the SPI FLASH
ARM: shmobile: koelsch legacy: Enable Quad SPI transfers for the SPI FLASH
ARM: shmobile: lager: switch to use dai info for R-Car sound
ARM: shmobile: bockw: switch to use dai info for R-Car sound
ARM: shmobile: bockw: remove old style audio clock
ARM: shmobile: Add Koelsch clock workarounds for SDHI
ARM: shmobile: Add Lager clock workarounds for SDHI and MMCIF
ARM: shmobile: lager-reference: Work around core clock issues
ARM: shmobile: koelsch-reference: Annotate clk_enables as __initconst
ARM: shmobile: koelsch-reference: Work around core clock issues
ARM: shmobile: lager: Annotate clk_names with __initconst
ARM: shmobile: koelsch: Annotate clk_names with __initconst
ARM: shmobile: Use shmobile_clk_workaround() on Koelsch
ARM: shmobile: Use shmobile_clk_workaround() on Lager
Soren Brinkmann [Sun, 4 May 2014 22:43:02 +0000 (15:43 -0700)]
net: macb: Fix race between HW and driver
Under "heavy" RX load, the driver cannot handle the descriptors fast
enough. In detail, when a descriptor is consumed, its used flag is
cleared and once the RX budget is consumed all descriptors with a
cleared used flag are prepared to receive more data. Under load though,
the HW may constantly receive more data and use those descriptors with a
cleared used flag before they are actually prepared for next usage.
The head and tail pointers into the RX-ring should always be valid and
we can omit clearing and checking of the used flag.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Soren Brinkmann [Sun, 4 May 2014 22:43:01 +0000 (15:43 -0700)]
net: macb: Remove 'unlikely' optimization
Coverage data suggests that the unlikely case of receiving data while
the receive handler is running may not be that unlikely.
Coverage data after running iperf for a while:
91320: 891: work_done = bp->macbgem_ops.mog_rx(bp, budget);
91320: 892: if (work_done < budget) {
2362: 893: napi_complete(napi);
-: 894:
-: 895: /* Packets received while interrupts were disabled */
4724: 896: status = macb_readl(bp, RSR);
2362: 897: if (unlikely(status)) {
762: 898: if (bp->caps & MACB_CAPS_ISR_CLEAR_ON_WRITE)
762: 899: macb_writel(bp, ISR, MACB_BIT(RCOMP));
-: 900: napi_reschedule(napi);
-: 901: } else {
1600: 902: macb_writel(bp, IER, MACB_RX_INT_FLAGS);
-: 903: }
-: 904: }
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Soren Brinkmann [Sun, 4 May 2014 22:42:59 +0000 (15:42 -0700)]
net: macb: Clear interrupt flags
A few interrupt flags were not cleared in the ISR, resulting in a sytem
trapped in the ISR in cases one of those interrupts occurred. Clear all
flags to avoid such situations.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Soren Brinkmann [Sun, 4 May 2014 22:42:58 +0000 (15:42 -0700)]
net: macb: Pass same size to DMA_UNMAP as used for DMA_MAP
Just as commit "net: macb: DMA-unmap full rx-buffer"
(48330e08fa168395b9fd9f369f06cca1df204361), pass the size that
was used for mapping the memory also to the unmap routine to
avoid warnings from the DMA_API.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Warren [Tue, 15 Apr 2014 21:10:27 +0000 (15:10 -0600)]
ARM: multi_v7: enable AT24C EEPROM driver
This is used for the board ID EEPROM on Jetson TK1, as well as likely
a whole slew of other NVIDIA reference boards; we simply haven't added
enabled the EEPROM in the DT files until now.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Olof Johansson <olof@lixom.net>
* tag 'renesas-soc-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7778/bockw: Move "select RENESAS_INTC_IRQPIN" under SoC
ARM: shmobile: Check r8a7791 MD21 at SMP boot
ARM: shmobile: rcar-gen2: Cache Mode Monitor Register Value
ARM: shmobile: Make use of r8a7790_add_standard_devices()
ARM: shmobile: Remove EMEV2 header file
ARM: shmobile: Remove legacy EMEV2 SoC support
ARM: shmobile: Add shared shmobile_init_delay()
ARM: shmobile: Update r8a7791 CPU freq to 1500MHz in C
Olof Johansson [Mon, 5 May 2014 20:42:47 +0000 (13:42 -0700)]
Merge branch 'next/boards' into for-next
* next/boards:
ARM: shmobile: Enable USB [EO]HCI HCD support in shmobile_defconfig
ARM: shmobile: Enable VSP1 in shmobile_defconfig
ARM: shmobile: Enable HIGHMEM in shmobile_defconfig
ARM: shmobile: Enable USBHS gadget support in shmobile_defconfig
ARM: shmobile: Include at24.c in shmobile_defconfig
ARM: shmobile: Include i2c-shmobile.c in shmobile_defconfig
ARM: shmobile: multiplatform: Enable MSIOF in defconfig
Olof Johansson [Mon, 5 May 2014 20:41:42 +0000 (13:41 -0700)]
Merge tag 'renesas-defconfig-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/boards
Merge "Renesas ARM Based SoC Defconfig Updates for v3.16" from Simon Horman:
SH Mobile Multi-Platform
* Enable USB [EO]HCI HCD, VSP1, HIGHMEM, USBHS, I2C_SH_MOBILE,
EEPROM_AT24 and MSIOF
* tag 'renesas-defconfig-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Enable USB [EO]HCI HCD support in shmobile_defconfig
ARM: shmobile: Enable VSP1 in shmobile_defconfig
ARM: shmobile: Enable HIGHMEM in shmobile_defconfig
ARM: shmobile: Enable USBHS gadget support in shmobile_defconfig
ARM: shmobile: Include at24.c in shmobile_defconfig
ARM: shmobile: Include i2c-shmobile.c in shmobile_defconfig
ARM: shmobile: multiplatform: Enable MSIOF in defconfig
Ying Cai [Sun, 4 May 2014 22:20:04 +0000 (15:20 -0700)]
ip_tunnel: Set network header properly for IP_ECN_decapsulate()
In ip_tunnel_rcv(), set skb->network_header to inner IP header
before IP_ECN_decapsulate().
Without the fix, IP_ECN_decapsulate() takes outer IP header as
inner IP header, possibly causing error messages or packet drops.
Note that this skb_reset_network_header() call was in this spot when
the original feature for checking consistency of ECN bits through
tunnels was added in eccc1bb8d4b4 ("tunnel: drop packet if ECN present
with not-ECT"). It was only removed from this spot in 3d7b46cd20e3
("ip_tunnel: push generic protocol handling to ip_tunnel module.").
Fixes: 3d7b46cd20e3 ("ip_tunnel: push generic protocol handling to ip_tunnel module.") Reported-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Ying Cai <ycai@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 5 May 2014 20:30:03 +0000 (16:30 -0400)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to e1000e only.
David provides four fixes for e1000e, first is a workaround for a hardware
erratum on 82579 devices which experienced packet loss in gigabit and 100
speeds when interconnect between the PHY and MAC is exiting K1 power saving
state. Second expands the scope of a workaround to include i217 and i218
parts as well to address over aggressive transmit behavior when connecting
at 10Mbs half-duplex. Next is to resolve a reported link flap issue on
82579 parts which was root caused as an interoperability problem between
82579 and at least some Broadcom PHYs in the Energy Efficient Ethernet wake
mechanism. Lastly, restricts the workaround of putting the PHY into MDIO
slow mode to access the PHY id to relevant parts since this issue has been
fixed on the newer hardware.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ertman [Thu, 1 May 2014 02:19:03 +0000 (02:19 +0000)]
e1000e: Restrict MDIO Slow Mode workaround to relevant parts
It has been determined that the workaround of putting the PHY into MDIO
slow mode to access the PHY id is not necessary with Lynx Point and newer
parts. The issue that necessitated the workaround has been fixed on the
newer hardware.
We will maintains, as a last ditch attempt, the conversion to MDIO Slow
Mode in the failure branch when attempting to access the PHY id so as to
cover all contingencies.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David Ertman [Thu, 1 May 2014 01:22:26 +0000 (01:22 +0000)]
e1000e: Fix issue with link flap on 82579
Several customers have reported a link flap issue on 82579. The symptoms
are random and intermittent link losses when 82579 is connected to specific
link partners. Issue has been root caused as interoperability problem
between 82579 and at least some Broadcom PHYs in the Energy Efficient
Ethernet wake mechanism.
To fix the issue, we are disabling the Phase Locked Loop shutdown in 100M
Low Power Idle. This solution will cause an increase of power in 100M EEE
link. It will cost additional 28mW in this specific mode.
Cc: Lukasz Adamczuk <lukasz.adamczuk@intel.com> Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David Ertman [Tue, 22 Apr 2014 05:48:54 +0000 (05:48 +0000)]
e1000e: Expand workaround for 10Mb HD throughput bug
In commit 772d05c51c4f4896c120ad418b1e91144a2ac813 "e1000e: slow performance
between two 82579 connected via 10Mbit hub", a workaround was put into place
to address the overaggressive transmit behavior of 82579 parts when connecting
at 10Mbs half-duplex.
This same behavior is seen on i217 and i218 parts as well. This patch expands
the original workaround to encompass these parts.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David Ertman [Tue, 22 Apr 2014 05:25:53 +0000 (05:25 +0000)]
e1000e: Workaround for dropped packets in Gig/100 speeds on 82579
This is a workaround for a HW erratum on 82579 devices.
Erratum is #23 in Intel 6 Series Chipset and Intel C200 Series Chipset
specification Update June 2013.
Problem: 82579 parts experience packet loss in Gig and 100 speeds
when interconnect between PHY and MAC is exiting K1 power saving state.
This was previously believed to only affect 1Gig speed, but has been observed
at 100Mbs also.
Workaround: Disable K1 for 82579 devices at Gig and 100 speeds.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David S. Miller [Mon, 5 May 2014 19:49:29 +0000 (15:49 -0400)]
Merge branch 'mlx4'
Or Gerlitz says:
====================
This series contains fixes for 3.15-rc, mostly around SRIOV. The patches by Jack,
Matan and myself fix few issues related to mlx4 SRIOV support for RoCE and single
port VFs, and the patch from Eyal eliminates checking PCI caps for VFs which is misleading.
Patches done against the net tree, commit 014f1b2 "net: bonding: Fix format string
mismatch in bond_sysfs.c"
We'd be happy to get Eyal's patch queued in your -stable list for 3.14.y
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eyal Perry [Sun, 4 May 2014 14:07:25 +0000 (17:07 +0300)]
net/mlx4_core: Don't issue PCIe speed/width checks for VFs
Carrying out PCI speed/width checks through pcie_get_minimum_link()
on VFs yield wrong results, so remove them.
Fixes: b912b2f ('net/mlx4_core: Warn if device doesn't have enough PCI bandwidth') Signed-off-by: Eyal Perry <eyalpe@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Sun, 4 May 2014 14:07:24 +0000 (17:07 +0300)]
net/mlx4_core: Load the Eth driver first
When running in SRIOV mode, VM that is assigned with a non-provisioned
Ethernet VFs get themselves a random mac when the Eth driver starts. In
this case, if the IB driver startup code that deals with RoCE runs first,
it will use a zero mac as the source mac for the Para-Virtual CM MADs
which is buggy. To handle that, we change the order of loading.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matan Barak [Sun, 4 May 2014 14:07:23 +0000 (17:07 +0300)]
net/mlx4_core: Fix slave id computation for single port VF
The code that deals with computing the slave id based on a given GID
gave wrong results when the number of single port VFs wasn't the
same for port 1 vs. port 2 and the relevant VF is single ported on
port 2. As a result, incoming CM MADs were dispatched to the wrong VF.
Fixed that and added documentation to clarify the computation steps.
Fixes: 449fc48 ('net/mlx4: Adapt code for N-Port VF') Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/mlx4_core: Adjust port number in qp_attach wrapper when detaching
When using single ported VFs and the VF is using port 2, we need
to adjust the port accordingly (change it from 1 to 2).
Fixes: 449fc48 ('net/mlx4: Adapt code for N-Port VF') Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Jack Morgenstein <jackm@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Fri, 2 May 2014 21:27:00 +0000 (23:27 +0200)]
net: cdc_ncm: fix buffer overflow
Commit 4d619f625a60 ("net: cdc_ncm: no point in filling up the NTBs
if we send ZLPs") changed the padding logic for devices with the ZLP
flag set. This meant that frames of any size will be sent without
additional padding, except for the single byte added if the size is
a multiple of the USB packet size. But if the unpadded size is
identical to the maximum frame size, and the maximum size is a
multiplum of the USB packet size, then this one-byte padding will
overflow the buffer.
Prevent padding if already at maximum frame size, letting usbnet
transmit a ZLP instead in this case.
Fixes: 4d619f625a60 ("net: cdc_ncm: no point in filling up the NTBs if we send ZLPs")
Reported by: Yu-an Shih <yshih@nvidia.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/built-in.o: In function `altera_tse_probe':
altera_tse_main.c:(.text+0x25ec2e): undefined reference to `dma_set_mask'
altera_tse_main.c:(.text+0x25ec78): undefined reference to `dma_supported'
altera_tse_main.c:(.text+0x25ecb6): undefined reference to `dma_supported'
drivers/built-in.o: In function `sgdma_async_read':
altera_sgdma.c:(.text+0x25f620): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `sgdma_uninitialize':
(.text+0x25f678): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `sgdma_uninitialize':
(.text+0x25f696): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `sgdma_initialize':
(.text+0x25f6f0): undefined reference to `dma_map_single'
drivers/built-in.o: In function `sgdma_initialize':
(.text+0x25f702): undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `sgdma_tx_buffer':
(.text+0x25f92a): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `sgdma_rx_status':
(.text+0x25fa24): undefined reference to `dma_sync_single_for_cpu'
make[3]: *** [vmlinux] Error 1
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Vince Bridgers <vbridgers2013@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy King [Thu, 1 May 2014 22:20:43 +0000 (15:20 -0700)]
vsock: Make transport the proto owner
Right now the core vsock module is the owner of the proto family. This
means there's nothing preventing the transport module from unloading if
there are open sockets, which results in a panic. Fix that by allowing
the transport to be the owner, which will refcount it properly.
Includes version bump to 1.0.1.0-k
Passes checkpatch this time, I swear...
Acked-by: Dmitry Torokhov <dtor@vmware.com> Signed-off-by: Andy King <acking@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Please pull the following batch of fixes intended for the 3.15 stream!
For the Bluetooth bits, Gustavo says:
"Some fixes for 3.15. There is a revert for the intel driver, a new
device id, and two important SSP fixes from Johan."
On top of that...
Ben Hutchings gives us a fix for an unbalanced irq enable in an
rtl8192cu error path.
Colin Ian King provides an rtlwifi fix for an uninitialized variable.
Felix Fietkau brings a pair of ath9k fixes, one that corrects a
hardware initialization value and another that removes an (unnecessary)
flag that was being used in a way that led to a software tx queue
hang in ath9k.
Gertjan van Wingerde pushes a MAINTAINERS change to remove himself
from the rt2x00 maintainer team.
Hans de Goede fixes a brcmfmac firmware load hang.
Larry Finger changes rtlwifi to use the correct queue for V0 traffic
on rtl8192se.
Rajkumar Manoharan corrects a race in ath9k driver initialization.
Stanislaw Gruszka fixes an rt2x00 bug in which disabling beaconing
once on USB devices led to permanently disabling beaconing for those
devices.
Tim Harvey provides fixes for a pair of ath9k issues that can lead
to soft lockups in that driver.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Unpaired quotes really confuse mutt when copy & pasting it into the To:
form.
Signed-off-by: Christoph Hellwig <hch@lst.de>
[ I'm going to remove all silly quotes entirely one day, but that day is
not today. So I'll just apply this - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 5 May 2014 14:48:50 +0000 (07:48 -0700)]
Merge tag 'upstream-3.15-rc5' of git://git.infradead.org/linux-ubifs
Pull ubifs fixes from Artem Bityutskiy:
"This includes the following fixes:
- two real bug-fixes from Tanya for the still "experimental" UBI
fastmap feature
- a one-liner from Kees which hardens kernel security
- a small error-path fix, where we forget to free various resources
in case of failure - spotted by the 'smatch' tool"
* tag 'upstream-3.15-rc5' of git://git.infradead.org/linux-ubifs:
UBI: avoid workqueue format string leak
UBI: fix ubi free PEBs count calculation
UBI: fix error path in __wl_get_peb
UBIFS: fix remount error path
Matthew Daley [Mon, 28 Apr 2014 07:05:21 +0000 (19:05 +1200)]
floppy: don't write kernel-only members to FDRAWCMD ioctl output
Do not leak kernel-only floppy_raw_cmd structure members to userspace.
This includes the linked-list pointer and the pointer to the allocated
DMA space.
Signed-off-by: Matthew Daley <mattd@bugfuzz.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Matthew Daley [Mon, 28 Apr 2014 07:05:20 +0000 (19:05 +1200)]
floppy: ignore kernel-only members in FDRAWCMD ioctl input
Always clear out these floppy_raw_cmd struct members after copying the
entire structure from userspace so that the in-kernel version is always
valid and never left in an interdeterminate state.
Signed-off-by: Matthew Daley <mattd@bugfuzz.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Anssi Hannula [Sun, 4 May 2014 23:38:43 +0000 (02:38 +0300)]
ALSA: hda - hdmi: Set converter channel count even without sink
Since commit 1df5a06a ("ALSA: hda - hdmi: Fix programmed active channel
count") channel count is no longer being set if monitor_present is 0.
This is because setting the count was moved after the CA value is
determined, which is only after the monitor_present check in
hdmi_setup_audio_infoframe().
Unfortunately, in some cases, such as with a non-spec-compliant codec or
with a problematic video driver, monitor_present is always 0. As a
specific example, this seems to happen with gen1 ATV (SiI1390 codec),
causing left-channel-only stereo playback (multi-channel playback has
apparently never worked with this codec despite it reporting 8 channels,
reason unknown).
Simply setting converter channel count without setting the pin infoframe
and channel mapping as well does not theoretically make much sense as
this will just mean they are out-of-sync and multichannel playback will
have a wrong channel mapping.
However, adding back just setting the converter channel count even in
no-monitor case is the safest change which at least fixes the stereo
playback regression on SiI1390 codec. Do that.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi> Reported-by: Stephan Raue <stephan@openelec.tv> Tested-by: Stephan Raue <stephan@openelec.tv> Cc: <stable@vger.kernel.org> # 3.12+ Signed-off-by: Takashi Iwai <tiwai@suse.de>
Jeff Mahoney [Sun, 27 Apr 2014 21:35:43 +0000 (17:35 -0400)]
s390/appldata: add slab.h for kzalloc/kfree
This fixes:
arch/s390/appldata/appldata_mem.c:135:2: error: implicit declaration of function 'kzalloc' [-Werror=implicit-function-declaration]
arch/s390/appldata/appldata_mem.c:141:3: error: implicit declaration of function 'kfree' [-Werror=implicit-function-declaration]
Signed-off-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
s390/uaccess: provide inline variants of get_user/put_user
This shortens the code by ~17k (performace_defconfig, march=z196).
The number of exception table entries however increases from 164
entries to 2500 entries (+~18k).
However the executed code is shorter and also faster since we save
the branches to the out-of-line copy_to/from_user implementations.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Merge remote-tracking branch 'anton/abiv2' into next
This series adds support for building the powerpc 64-bit
LE kernel using the new ABI v2. We already supported
running ABI v2 userspace programs but this adds support
for building the kernel itself using the new ABI.
projects / karo-tx-linux.git / log