The current initialisation code probes 'unsupported' AGP devices
simply by calling its own probe function. It does not lock these
devices or even check whether another driver is already bound to
them.
We must use the device core to manage this. So if the specific
device id table didn't match anything and agp_try_unsupported=1,
switch the device id table and call driver_attach() again.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The code that hashes and unhashes connections from the connection table
is missing locking of the connection being modified, which opens up a
race condition and results in memory corruption when this race condition
is hit.
Here is what happens in pretty verbose form:
CPU 0 CPU 1
------------ ------------
An active connection is terminated and
we schedule ip_vs_conn_expire() on this
CPU to expire this connection.
IRQ assignment is changed to this CPU,
but the expire timer stays scheduled on
the other CPU.
New connection from same ip:port comes
in right before the timer expires, we
find the inactive connection in our
connection table and get a reference to
it. We proper lock the connection in
tcp_state_transition() and read the
connection flags in set_tcp_state().
ip_vs_conn_expire() gets called, we
unhash the connection from our
connection table and remove the hashed
flag in ip_vs_conn_unhash(), without
proper locking!
While still holding proper locks we
write the connection flags in
set_tcp_state() and this sets the hashed
flag again.
ip_vs_conn_expire() fails to expire the
connection, because the other CPU has
incremented the reference count. We try
to re-insert the connection into our
connection table, but this fails in
ip_vs_conn_hash(), because the hashed
flag has been set by the other CPU. We
re-schedule execution of
ip_vs_conn_expire(). Now this connection
has the hashed flag set, but isn't
actually hashed in our connection table
and has a dangling list_head.
We drop the reference we held on the
connection and schedule the expire timer
for timeouting the connection on this
CPU. Further packets won't be able to
find this connection in our connection
table.
ip_vs_conn_expire() gets called again,
we think it's already hashed, but the
list_head is dangling and while removing
the connection from our connection table
we write to the memory location where
this list_head points to.
The result will probably be a kernel oops at some other point in time.
This race condition is pretty subtle, but it can be triggered remotely.
It needs the IRQ assignment change or another circumstance where packets
coming from the same ip:port for the same service are being processed on
different CPUs. And it involves hitting the exact time at which
ip_vs_conn_expire() gets called. It can be avoided by making sure that
all packets from one connection are always processed on the same CPU and
can be made harder to exploit by changing the connection timeouts to
some custom values.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net> Acked-by: Simon Horman <horms@verge.net.au> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix subsequent suspends by issuing tpm_continue_selftest during resume.
Otherwise, the tpm chip seems to be not fully initialized and will reject
the save state command during suspend, thus preventing the whole system
to suspend.
Code did not handle projected 2d and depth coordinates, meaning potentially
set 3d or cube special handling might stick.
(Not sure what depth coord actually does, but I guess handling it
like a normal coordinate is the right thing to do.)
Might be related to https://bugs.freedesktop.org/show_bug.cgi?id=26428
Signed-off-by: sroland@vmware.com Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes an Ironlake laptop with a 68.940MHz 1280x800 panel and 120MHz SSC
reference clock.
More generally, the 0.488% tolerance used before is just too tight to
reliably find a PLL setting. I extracted the search algorithm and
modified it to find the dot clocks with maximum error over the valid
range for the given output type:
A lot of 945GMs have had stability issues for a long time, this manifested as X hangs, blitter engine hangs, and lots of crashes.
one such report is at:
https://bugs.freedesktop.org/show_bug.cgi?id=20560
along with numerous distro bugzillas.
This only took a week of digging and hair ripping to figure out.
Tracked down and tested on a 945GM Lenovo T60,
previously running
x11perf -copypixwin500
or
x11perf -copywinpix500
repeatedly would cause the GPU to wedge within 4 or 5 tries, with random busy bits set.
After this patch no hangs were observed.
Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the call to ddebug_remove_module() down into free_module(). In this
way it should be called from all error paths. Currently, we are missing
the remove if the module init routine fails.
Signed-off-by: Jason Baron <jbaron@redhat.com> Reported-by: Thomas Renninger <trenn@suse.de> Tested-by: Thomas Renninger <trenn@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
1. The BTRFS_IOC_CLONE and BTRFS_IOC_CLONE_RANGE ioctls should check
whether the donor file is append-only before writing to it.
2. The BTRFS_IOC_CLONE_RANGE ioctl appears to have an integer
overflow that allows a user to specify an out-of-bounds range to copy
from the source file (if off + len wraps around). I haven't been able
to successfully exploit this, but I'd imagine that a clever attacker
could use this to read things he shouldn't. Even if it's not
exploitable, it couldn't hurt to be safe.
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com> Signed-off-by: Chris Mason <chris.mason@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
changes:
v2 Added missing break (Johannes)
v3 Broke original patch into two (Johannes)
Signed-off-by: Javier Cardona <javier@cozybit.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a missing element of the ReadPubEK command output,
that prevents future overflow of this buffer when copying the
TPM output result into it.
Prevents a kernel panic in case the user tries to read the
pubek from sysfs.
Use an irq spinlock to hold off the IRQ handler until
enough early card init is complete such that the handler
can run without faulting.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If bit 29 is set, MAC H/W can attempt to decrypt the received aggregate
with WEP or TKIP, eventhough the received frame may be a CRC failed
corrupted frame. If this bit is set, H/W obeys key type in keycache.
If it is not set and if the key type in keycache is neither open nor
AES, H/W forces key type to be open. But bit 29 should be set to 1
for AsyncFIFO feature to encrypt/decrypt the aggregate with WEP or TKIP.
Reported-by: Johan Hovold <johan.hovold@lundinova.se> Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: Ranga Rao Ravuri <ranga.ravuri@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The newer single chip hardware family of chipsets have not been
experiencing issues with power saving set by default with recent
fixes merged (even into stable). The remaining issues are only
reported with AR5416 and since enabling PS by default can increase
power savings considerably best to take advantage of that feature
as this has been tested properly.
For more details on this issue see the bug report:
http://bugzilla.kernel.org/show_bug.cgi?id=14267
We leave AR5416 with PS disabled by default, that seems to require
some more work.
Cc: Peter Stuge <peter@stuge.se> Cc: Justin P. Mattock <justinmattock@gmail.com> Cc: Kristoffer Ericson <kristoffer.ericson@gmail.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jumbo frames are not supported, and if they are seen it is likely
a bogus frame so just silently discard them instead of warning on
them all time. Also, instead of dropping them immediately though
move the check *after* we check for all sort of frame errors. This
should enable us to discard these frames if the hardware picks
other bogus items first. Lets see if we still get those jumbo
counters increasing still with this.
Jumbo frames would happen if we tell hardware we can support
a small 802.11 chunks of DMA'd frame, hardware would split RX'd
frames into parts and we'd have to reconstruct them in software.
This is done with USB due to the bulk size but with ath5k we
already provide a good limit to hardware and this should not be
happening.
This is reported quite often and if it fills the logs then this
needs to be addressed and to avoid spurious reports.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the attempt to read the calldir fails, then instead of storing the read
bytes, we currently discard them. This leads to a garbage final result when
upon re-entry to the same routine, we read the remaining bytes.
Fixes the regression in bugzilla number 16213. Please see
https://bugzilla.kernel.org/show_bug.cgi?id=16213
The kernel's math-emu code contains a macro _FP_FROM_INT() which is
used to convert an integer to a raw normalized floating-point value.
It does this basically in three steps:
1. Compute the exponent from the number of leading zero bits.
2. Downshift large fractions to put the MSB in the right position
for normalized fractions.
3. Upshift small fractions to put the MSB in the right position.
There is an boundary error in step 2, causing a fraction with its
MSB exactly one bit above the normalized MSB position to not be
downshifted. This results in a non-normalized raw float, which when
packed becomes a massively inaccurate representation for that input.
The impact of this depends on a number of arch-specific factors,
but it is known to have broken emulation of FXTOD instructions
on UltraSPARC III, which was originally reported as GCC bug 44631
<http://gcc.gnu.org/bugzilla/show_bug.cgi?id=44631>.
Any arch which uses math-emu to emulate conversions from integers to
same-size floats may be affected.
The fix is simple: the exponent comparison used to determine if the
fraction should be downshifted must be "<=" not "<".
I'm sending a kernel module to test this as a reply to this message.
There are also SPARC user-space test cases in the GCC bug entry.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch allows us to treat the alternate mac address as though it is the
physical address on the adapter. This is accomplished by letting the
alt_mac_address function to only fail on an NVM error. If no errors occur
and the alternate mac address is not present then RAR0 is read as the
default mac address.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Brandon Philips <bphilips@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
sky2_phy_reinit is called by the ethtool helpers sky2_set_settings,
sky2_nway_reset and sky2_set_pauseparam when netif_running.
However, at the end of sky2_phy_init GM_GP_CTRL has GM_GPCR_RX_ENA and
GM_GPCR_TX_ENA cleared. So, doing these commands causes the device to
stop working:
$ ethtool -r eth0
$ ethtool -A eth0 autoneg off
Fix this issue by enabling Rx/Tx after running sky2_phy_init in
sky2_phy_reinit.
Signed-off-by: Brandon Philips <bphilips@suse.de> Tested-by: Brandon Philips <bphilips@suse.de> Cc: stable@kernel.org Tested-by: Mike McCormack <mikem@ring3k.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the call to phy_connect fails, we will return directly instead of freeing
the previously allocated struct net_device.
Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the security problem in the CIFS filesystem DNS lookup code in which a
malicious redirect could be installed by a random user by simply adding a
result record into one of their keyrings with add_key() and then invoking a
CIFS CFS lookup [CVE-2010-2524].
This is done by creating an internal keyring specifically for the caching of
DNS lookups. To enforce the use of this keyring, the module init routine
creates a set of override credentials with the keyring installed as the thread
keyring and instructs request_key() to only install lookup result keys in that
keyring.
The override is then applied around the call to request_key().
This has some additional benefits when a kernel service uses this module to
request a key:
(1) The result keys are owned by root, not the user that caused the lookup.
(2) The result keys don't pop up in the user's keyrings.
(3) The result keys don't come out of the quota of the user that caused the
lookup.
The keyring can be viewed as root by doing cat /proc/keys:
# keyctl list 0x2a0ca6c3
1 key in keyring: 726766307: --alswrv 0 0 dns_resolver: foo.bar.com
Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-and-Tested-by: Jeff Layton <jlayton@redhat.com> Acked-by: Steve French <smfrench@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This bug appears to be the result of a cut-and-paste mistake from the
NTLMv1 code. The function to generate the MAC key was commented out, but
not the conditional above it. The conditional then ended up causing the
session setup key not to be copied to the buffer unless this was the
first session on the socket, and that made all but the first NTLMv2
session setup fail.
Fix this by removing the conditional and all of the commented clutter
that made it difficult to see.
The IT8720F has no VIN7 pin, so VCCH should always be routed
internally to VIN7 with an internal divider. Curiously, there still
is a configuration bit to control this, which means it can be set
incorrectly. And even more curiously, many boards out there are
improperly configured, even though the IT8720F datasheet claims that
the internal routing of VCCH to VIN7 is the default setting. So we
force the internal routing in this case.
It turns out that all boards with the wrong setting are from Gigabyte,
so I suspect a BIOS bug. But it's easy enough to workaround in the
driver, so let's do it.
Reported temperature for ASB1 CPUs is too high.
Add ASB1 CPU revisions (these are also non-desktop variants) to the
list of CPUs for which the temperature fixup is not required.
Example: (from LENOVO ThinkPad Edge 13, 01972NG, system was idle)
Current kernel reports
$ sensors
k8temp-pci-00c3
Adapter: PCI adapter
Core0 Temp: +74.0 C
Core0 Temp: +70.0 C
Core1 Temp: +69.0 C
Core1 Temp: +70.0 C
With this patch I have
$ sensors
k8temp-pci-00c3
Adapter: PCI adapter
Core0 Temp: +54.0 C
Core0 Temp: +51.0 C
Core1 Temp: +48.0 C
Core1 Temp: +49.0 C
Cc: Rudolf Marek <r.marek@assembler.cz> Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit a2e066bba2aad6583e3ff648bf28339d6c9f0898 introduced core
swapping for CPU models 64 and later. I recently had a report about
a Sempron 3200+, model 95, for which this patch broke temperature
reading. It happens that this is a single-core processor, so the
effect of the swapping was to read a temperature value for a core
that didn't exist, leading to an incorrect value (-49 degrees C.)
Disabling core swapping on singe-core processors should fix this.
Additional comment from Andreas:
The BKDG says
Thermal Sensor Core Select (ThermSenseCoreSel)-Bit 2. This bit
selects the CPU whose temperature is reported in the CurTemp
field. This bit only applies to dual core processors. For
single core processors CPU0 Thermal Sensor is always selected.
k8temp_probe() correctly detected that SEL_CORE can't be used on single
core CPU. Thus k8temp did never update the temperature values stored
in temp[1][x] and -49 degrees was reported. For single core CPUs we
must use the values read into temp[0][x].
Signed-off-by: Jean Delvare <khali@linux-fr.org> Tested-by: Rick Moritz <rhavin@gmx.net> Acked-by: Andreas Herrmann <andreas.herrmann3@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Christoph Fritz [Sun, 11 Jul 2010 23:26:15 +0000 (18:26 -0500)]
ssb: Handle Netbook devices where the SPROM address is changed
For some Netbook computers with Broadcom BCM4312 wireless interfaces,
the SPROM has been moved to a new location. When the ssb driver tries to
read the old location, the systems hangs when trying to read a
non-existent location. Such freezes are particularly bad as they do not
log the failure.
This patch is modified from commit da1fdb02d9200ff28b6f3a380d21930335fe5429 with some pieces from other
mainline changes so that it can be applied to stable 2.6.34.Y.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
virtio-pci resets the device at startup by writing to the status
register, but this does not clear the pci config space,
specifically msi enable status which affects register
layout.
This breaks things like kdump when they try to use e.g. virtio-blk.
Fix by forcing msi off at startup. Since pci.c already has
a routine to do this, we export and use it instead of duplicating code.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Tested-by: Vivek Goyal <vgoyal@redhat.com> Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org> Cc: linux-pci@vger.kernel.org Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On specific platforms, MSI is unreliable on some of the QLA24xx chips, resulting
in fatal I/O errors under load, as reported in <http://bugs.debian.org/572322>
and by some RHEL customers.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
find_keyring_by_name() can gain access to a keyring that has had its reference
count reduced to zero, and is thus ready to be freed. This then allows the
dead keyring to be brought back into use whilst it is being destroyed.
This problem is that find_keyring_by_name does not confirm that the keyring is
valid before accepting it.
Skipping keyrings that have been reduced to a zero count seems the way to go.
To this end, use atomic_inc_not_zero() to increment the usage count and skip
the candidate keyring if that returns false.
The following script _may_ cause the bug to happen, but there's no guarantee
as the window of opportunity is small:
Clear the floating point exception flag before returning to
user space. This is needed, else the libc trampoline handler
may hit the same SIGFPE again while building up a trampoline
to a signal handler.
Roedel, Joerg [Thu, 6 May 2010 09:38:43 +0000 (11:38 +0200)]
KVM: x86: Inject #GP with the right rip on efer writes
This patch fixes a bug in the KVM efer-msr write path. If a
guest writes to a reserved efer bit the set_efer function
injects the #GP directly. The architecture dependent wrmsr
function does not see this, assumes success and advances the
rip. This results in a #GP in the guest with the wrong rip.
This patch fixes this by reporting efer write errors back to
the architectural wrmsr function.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
(cherry picked from commit b69e8caef5b190af48c525f6d715e7b7728a77f6)
Avi Kivity [Tue, 4 May 2010 12:00:37 +0000 (15:00 +0300)]
KVM: Fix wallclock version writing race
Wallclock writing uses an unprotected global variable to hold the version;
this can cause one guest to interfere with another if both write their
wallclock at the same time.
Acked-by: Glauber Costa <glommer@redhat.com> Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
(cherry picked from commit 9ed3c444ab8987c7b219173a2f7807e3f71e234e)
Shane Wang [Thu, 29 Apr 2010 16:09:01 +0000 (12:09 -0400)]
KVM: VMX: enable VMXON check with SMX enabled (Intel TXT)
Per document, for feature control MSR:
Bit 1 enables VMXON in SMX operation. If the bit is clear, execution
of VMXON in SMX operation causes a general-protection exception.
Bit 2 enables VMXON outside SMX operation. If the bit is clear, execution
of VMXON outside SMX operation causes a general-protection exception.
This patch is to enable this kind of check with SMX for VMXON in KVM.
Signed-off-by: Shane Wang <shane.wang@intel.com> Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
(cherry picked from commit cafd66595d92591e4bd25c3904e004fc6f897e2d)
Avi Kivity [Wed, 12 May 2010 08:48:18 +0000 (11:48 +0300)]
KVM: MMU: Segregate shadow pages with different cr0.wp
When cr0.wp=0, we may shadow a gpte having u/s=1 and r/w=0 with an spte
having u/s=0 and r/w=1. This allows excessive access if the guest sets
cr0.wp=1 and accesses through this spte.
Fix by making cr0.wp part of the base role; we'll have different sptes for
the two cases and the problem disappears.
Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
(cherry picked from commit 3dbe141595faa48a067add3e47bba3205b79d33c)
Glauber Costa [Tue, 11 May 2010 16:17:40 +0000 (12:17 -0400)]
x86, paravirt: Add a global synchronization point for pvclock
In recent stress tests, it was found that pvclock-based systems
could seriously warp in smp systems. Using ingo's time-warp-test.c,
I could trigger a scenario as bad as 1.5mi warps a minute in some systems.
(to be fair, it wasn't that bad in most of them). Investigating further, I
found out that such warps were caused by the very offset-based calculation
pvclock is based on.
This happens even on some machines that report constant_tsc in its tsc flags,
specially on multi-socket ones.
Two reads of the same kernel timestamp at approx the same time, will likely
have tsc timestamped in different occasions too. This means the delta we
calculate is unpredictable at best, and can probably be smaller in a cpu
that is legitimately reading clock in a forward ocasion.
Some adjustments on the host could make this window less likely to happen,
but still, it pretty much poses as an intrinsic problem of the mechanism.
A while ago, I though about using a shared variable anyway, to hold clock
last state, but gave up due to the high contention locking was likely
to introduce, possibly rendering the thing useless on big machines. I argue,
however, that locking is not necessary.
We do a read-and-return sequence in pvclock, and between read and return,
the global value can have changed. However, it can only have changed
by means of an addition of a positive value. So if we detected that our
clock timestamp is less than the current global, we know that we need to
return a higher one, even though it is not exactly the one we compared to.
OTOH, if we detect we're greater than the current time source, we atomically
replace the value with our new readings. This do causes contention on big
boxes (but big here means *BIG*), but it seems like a good trade off, since
it provide us with a time source guaranteed to be stable wrt time warps.
After this patch is applied, I don't see a single warp in time during 5 days
of execution, in any of the machines I saw them before.
Signed-off-by: Glauber Costa <glommer@redhat.com> Acked-by: Zachary Amsden <zamsden@redhat.com> CC: Jeremy Fitzhardinge <jeremy@goop.org> CC: Avi Kivity <avi@redhat.com> CC: Marcelo Tosatti <mtosatti@redhat.com> CC: Zachary Amsden <zamsden@redhat.com> Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
(cherry picked from commit 489fb490dbf8dab0249ad82b56688ae3842a79e8)
Synaptics hardware requires resetting device after suspend to ram
in order for the device to be operational. The reset lives in
synaptics-specific reconnect handler, but it is not being invoked
if synaptics support is disabled and the device is handled as a
standard PS/2 device (bare or IntelliMouse protocol).
Let's add reset into generic reconnect handler as well.
What happens is that, when the tipc module in inserted it enters a standalone
node mode in which communication to its own address is allowed <0.0.0> but not
to other addresses, since the appropriate data structures have not been
allocated yet (specifically the tipc_net pointer). There is nothing stopping a
client from trying to send such a message however, and if that happens, we
attempt to dereference tipc_net.zones while the pointer is still NULL, and
explode. The fix is pretty straightforward. Since these oopses all arise from
the dereference of global pointers prior to their assignment to allocated
values, and since these allocations are small (about 2k total), lets convert
these pointers to static arrays of the appropriate size. All the accesses to
these bits consider 0/NULL to be a non match when searching, so all the lookups
still work properly, and there is no longer a chance of a bad dererence
anywhere. As a bonus, this lets us eliminate the setup/teardown routines for
those pointers, and elimnates the need to preform any locking around them to
prevent access while their being allocated/freed.
I've updated the tipc_net structure to behave this way to fix the exact reported
problem, and also fixed up the tipc_bearers and media_list arrays to fix an
obvious simmilar problem that arises from issuing tipc-config commands to
manipulate bearers/links prior to entering networked mode
I've tested this for a few hours by running the sanity tests and stress test
with the tipcutils suite, and nothing has fallen over. There have been a few
lockdep warnings, but those were there before, and can be addressed later, as
they didn't actually result in any deadlock.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: Allan Stephens <allan.stephens@windriver.com> CC: David S. Miller <davem@davemloft.net> CC: tipc-discussion@lists.sourceforge.net Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 7583605b6d29f1f7f6fc505b883328089f3485ad ("ucc_geth: Fix empty
TX queue processing") fixed empty TX queue mishandling, but didn't
account another corner case: when TX queue becomes full.
Without this patch the driver will stop transmiting when TX queue
becomes full since 'bd == ugeth->txBd[txQ]' actually checks for
two things: queue empty or full.
Let's better check for NULL skb, which unambiguously signals an empty
queue.
Signed-off-by: Jiajun Wu <b06378@freescale.com> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since commit 864fdf884e82bacbe8ca5e93bd43393a61d2e2b4 ("ucc_geth:
Fix hangs after switching from full to half duplex") ucc_geth driver
disables the controller during MAC configuration changes. Though,
disabling the controller might take quite awhile, and so the netdev
watchdog might get upset:
This patch fixes the issue by detaching the netdev during the
time we change the configuration.
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Tested-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Unable to handle kernel paging request for data at address 0x00000058
Faulting instruction address: 0xc024f2fc
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [c024f2fc] skb_recycle_check+0x14/0x100
LR [e30aa0a4] ucc_geth_poll+0xd8/0x4e0 [ucc_geth_driver]
Call Trace:
[df857d50] [c000b03c] __ipipe_grab_irq+0x3c/0xa4 (unreliable)
[df857d60] [e30aa0a4] ucc_geth_poll+0xd8/0x4e0 [ucc_geth_driver]
[df857dd0] [c0258cf8] net_rx_action+0xf8/0x1b8
[df857e10] [c0032a38] __do_softirq+0xb8/0x13c
[df857e60] [c00065cc] do_softirq+0xa0/0xac
[...]
This is because ucc_geth_tx() tries to process an empty queue when
queues are logically stopped. Stopping the queues doesn't disable
polling, and since nowadays ucc_geth_tx() is actually called from
the polling routine, the oops above might pop up.
Fix this by removing 'netif_queue_stopped() == 0' check.
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Tested-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On btrfs, do the following
------------------
# su user1
# cd btrfs-part/
# touch aaa
# getfacl aaa
# file: aaa
# owner: user1
# group: user1
user::rw-
group::rw-
other::r--
# su user2
# cd btrfs-part/
# setfacl -m u::rwx aaa
# getfacl aaa
# file: aaa
# owner: user1
# group: user1
user::rwx <- successed to setfacl
group::rw-
other::r--
------------------
but we should prohibit it that user2 changing user1's acl.
In fact, on ext3 and other fs, a message occurs:
setfacl: aaa: Operation not permitted
This patch fixed it.
Signed-off-by: Shi Weihua <shiwh@cn.fujitsu.com> Signed-off-by: Chris Mason <chris.mason@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When transmitting L2TP frames, we derive the outgoing interface's UDP
checksum hardware assist capabilities from the tunnel dst dev. This
can sometimes be NULL, especially when routing protocols are used and
routing changes occur. This patch just checks for NULL dst or dev
pointers when checking for netdev hardware assist features.
Signed-off-by: James Chapman <jchapman@katalix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a new UMOUNT_NOFOLLOW flag to umount(2). This is needed to prevent
symlink attacks in unprivileged unmounts (fuse, samba, ncpfs).
Additionally, return -EINVAL if an unknown flag is used (and specify
an explicitly unused flag: UMOUNT_UNUSED). This makes it possible for
the caller to determine if a flag is supported or not.
CC: Eugene Teo <eugene@redhat.com> CC: Michael Kerrisk <mtk.manpages@gmail.com> Signed-off-by: Miklos Szeredi <mszeredi@suse.cz> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While creating a file on a server which supports unix extensions
such as Samba, if a file is being created which does not supply
nameidata (i.e. nd is null), cifs client can oops when calling
cifs_posix_open.
Signed-off-by: Shirish Pargaonkar <shirishp@us.ibm.com> Signed-off-by: Steve French <sfrench@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Its an skb_over_panic BUG halt that results from processing an init chunk in
which too many of its variable length parameters are in some way malformed.
The problem is in sctp_process_unk_param:
if (NULL == *errp)
*errp = sctp_make_op_error_space(asoc, chunk,
ntohs(chunk->chunk_hdr->length));
if (*errp) {
sctp_init_cause(*errp, SCTP_ERROR_UNKNOWN_PARAM,
WORD_ROUND(ntohs(param.p->length)));
sctp_addto_chunk(*errp,
WORD_ROUND(ntohs(param.p->length)),
param.v);
When we allocate an error chunk, we assume that the worst case scenario requires
that we have chunk_hdr->length data allocated, which would be correct nominally,
given that we call sctp_addto_chunk for the violating parameter. Unfortunately,
we also, in sctp_init_cause insert a sctp_errhdr_t structure into the error
chunk, so the worst case situation in which all parameters are in violation
requires chunk_hdr->length+(sizeof(sctp_errhdr_t)*param_count) bytes of data.
The result of this error is that a deliberately malformed packet sent to a
listening host can cause a remote DOS, described in CVE-2010-1173:
http://cve.mitre.org/cgi-bin/cvename.cgi?name=2010-1173
I've tested the below fix and confirmed that it fixes the issue. We move to a
strategy whereby we allocate a fixed size error chunk and ignore errors we don't
have space to report. Tested by me successfully
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
wl1251_sdio_probe() error path is missing wl1251_free_hw, add it.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Acked-by: Kalle Valo <kvalo@adurom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We currently have this check as a BUG_ON, which is being hit by people.
Previously it was an error with a recalculation if not current, return that
code.
... the portion adding the BUG_ON is reverted since we are encountering the error
and BUG_ON was created with assumption that error is not encountered.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Error checking for aggregation frames should go into aggregation queue,
if aggregation queue not available, use legacy queue instead.
Also make sure the aggregation queue is available to activate,
if driver and mac80211 is out-of-sync, try to disable the queue and
sync-up with mac80211.
These old machines more often than not lie about their lid state. So
don't use it to detect LVDS presence, but leave the event handler to
deal with lid open/close, when we might need to reset the mode.
Fixes kernel bug #15248
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Eric Anholt <eric@anholt.net> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some single chip family devices are sold in the market with
802.11n bonded out, these have no hardware capability for
802.11n but ath9k can still support them. These are called
AR2427.
[bwh: backported to 2.6.32] Reported-by: Rolf Leggewie <bugzilla.kernel.org@rolf.leggewie.biz> Tested-by: Bernhard Reiter <ockham@raz.or.at> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Previously, cfg80211 had reported "0" for MCS (i.e. 802.11n) bitrates
through the wireless extensions interface. However, nl80211 was
converting MCS rates into a reasonable bitrate number. This patch moves
the nl80211 code to cfg80211 where it is now shared between both the
nl80211 interface and the wireless extensions interface.
Signed-off-by: John W. Linville <linville@tuxdriver.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
3c509 was changed to support ethtool in 2002, making the 'xcvr' module
parameter obsolete in most cases. More recently 3c509 was converted
to the modern driver model and this parameter was removed. Fix the
documentation to refer to ethtool rather than the module parameter.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Davicom DM9100 and DM9102 chips are used on the motherboards of
some SPARC systems (supported by the tulip driver) and also in PCI
expansion cards (supported by the dmfe driver). There is no
difference in the PCI device ids for the two different configurations,
so these drivers both claim the device ids. However, it is possible
to distinguish the two configurations by the presence of Open Firmware
properties for them, so we do that.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Grant Grundler <grundler@parisc-linux.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
velocity_open() calls velocity_give_many_rx_descs(), which gives RX
descriptors to the NIC, before installing an interrupt handler or
calling velocity_init_registers(). I think this is very unsafe and it
appears to explain the bug report <http://bugs.debian.org/508527>.
On MTU change, velocity_give_many_rx_descs() is again called before
velocity_init_registers(). I'm not sure whether this is unsafe but
it does look wrong.
Therefore, move the calls to velocity_give_many_rx_descs() after
request_irq() and velocity_init_registers().
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Tested-by: Jan Ceuleers <jan.ceuleers@computer.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add Dell WLA3310 USB wireless card, which has a Z-Com XG-705A chipset, to the
USB Ids in p54usb.
Signed-off-by: Jason Dravet <dravet@hotmail.com> Tested-by: Richard Gregory Tillmore <rtillmore@gmail.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Acked-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes resource reclaim in error path of acm_probe:
1. In the case of "out of memory (read urbs usb_alloc_urb)\n")", there
is no need to call acm_read_buffers_free(acm) here. Fix it by goto
alloc_fail6 instead of alloc_fail7.
2. In the case of "out of memory (write urbs usb_alloc_urb)",
usb_alloc_urb may fail in any iteration of the for loop. Current
implementation does not properly free allocated snd->urb. Fix it by
goto alloc_fail8 instead of alloc_fail7.
3. In the case of device_create_file(&intf->dev,&dev_attr_iCountryCodeRelDate)
fail, acm->country_codes is kfreed. As a result, device_remove_file
for dev_attr_wCountryCodes will not be executed in acm_disconnect.
Fix it by calling device_remove_file for dev_attr_wCountryCodes
before goto skip_countries.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Call set_mctrl() and clear_mctrl() according to the flow control mode
selected. This makes serial communication for FT232 connected devices
work when CRTSCTS is not set.
This fixes a regression introduced by 4175f3e31 ("tty_port: If we are
opened non blocking we still need to raise the carrier"). This patch
calls the low-level driver's dtr_rts() function which consequently sets
TIOCM_DTR | TIOCM_RTS. A later call to set_termios() without CRTSCTS in
cflags, however, does not reset these bits, and so data is not actually
sent out on the serial wire.
Signed-off-by: Daniel Mack <daniel@caiaq.de> Cc: Johan Hovold <jhovold@gmail.com> Cc: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After software resets an xHCI host controller, it must wait for the
"Controller Not Ready" (CNR) bit in the status register to be cleared.
Software is not supposed to ring any doorbells or write to any registers
except the status register until this bit is cleared.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the run bit is set in the xHCI command register, it may take a few
microseconds for the host to start running. We cannot ring any doorbells
until the host is actually running, so wait until the status register says
the host is running.
vt6421 has problems talking to recent WD drives. It causes a lot of
transmission errors while high bandwidth transfer as reported in the
following bugzilla entry.
https://bugzilla.kernel.org/show_bug.cgi?id=15173
Joseph Chan provided the following fix. I don't have any idea what it
does but I can verify the issue is gone with the patch applied.
Signed-off-by: Tejun Heo <tj@kernel.org>
Originally-from: Joseph Chan <JosephChan@via.com.tw> Reported-by: Jorrit Tijben <sjorrit@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On mcp55, nIEN gets stuck once set and liteon blueray rom iHOS104-08
violates ATA specification and fails to set I on D2H Reg FIS if nIEN
is set when the command was issued. When the other party is following
the spec, both devices can work fine but when the two flaws are put
together, they can't talk to each other.
mcp55 has its own IRQ masking mechanism and there's no reason to mess
with nIEN in the first place. Fix it by dropping nIEN diddling from
nv_mcp55_freeze/thaw().
This was originally reported by Cengiz. Although Cengiz hasn't
verified the fix yet, I could reproduce this problem and verfiy the
fix. Even if Cengiz is experiencing different or additional problems,
this patch is needed.
If reserve_pmc_hardware() succeeds but reserve_ds_buffers()
fails, then we need to release_pmc_hardware. It won't be done
by the destroy() callback because we return before setting it
in case of error.
Per IEEE 1394 clause 8.4.2.3, a contender for the IRM role shall check
whether the current IRM complies to 1394a-2000 or later. If not force a
compliant node (e.g. itself) to become IRM. This was implemented in the
older ieee1394 driver but not yet in firewire-core.
An older Sony camcorder (Sony DCR-TRV25) which implements 1394-1995 IRM
but neither 1394a-2000 IRM nor BM was now found to cause an
interoperability bug:
- Camcorder becomes root node when plugged in, hence gets IRM role.
- firewire-core successfully contends for BM role, proceeds to perform
gap count optimization and resets the bus.
- Sony camcorder ignores presence of a BM (against the spec, this is
a firmware bug), performs its idea of gap count optimization and
resets the bus.
- Preceding two steps are repeated endlessly, bus never settles,
regular I/O is practically impossible.
http://thread.gmane.org/gmane.linux.kernel.firewire.user/3913
This is an interoperability regression from the old to the new drivers.
Fix it indirectly by adding the 1394a IRM check. The spec suggests
three and a half methods to determine 1394a compliance of a remote IRM;
we choose the method of testing the Config_ROM.Bus_Info.generation
field. This is data that firewire-core should have readily available at
this point, i.e. does not require extra I/O.
Reported-by: Clemens Ladisch <clemens@ladisch.de> (missing 1394a check) Reported-by: H. S. <hs.samix@gmail.com> (issue with Sony DCR-TRV25) Tested-by: H. S. <hs.samix@gmail.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
JMB362 is a new variant of jmicron controller which is similar to
JMB360 but has two SATA ports instead of one. As there is no PATA
port, single function AHCI mode can be used as in JMB360. Add pci
quirk for JMB362.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Aries Lee <arieslee@jmicron.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 56d1de0a21db28e41741cfa0a66e18bc8d920554, "ath5k: clean up
filter flags setting" introduced a regression in monitor mode such
that the promisc filter flag would get lost.
Although we set the promisc flag when it changed, we did not
preserve it across subsequent calls to configure_filter. This patch
restores the original functionality.
Bisected-by: weedy2887@gmail.com Tested-by: weedy2887@gmail.com Tested-by: Rick Farina <sidhayn@gmail.com> Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Based on the sh_tmu change in 66f49121ffa41a19c59965b31b046d8368fec3c7
("clocksource: sh_tmu: compute mult and shift before registration").
The same issues impact the sh_cmt driver, so we take the same approach
here.
Signed-off-by: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Correct at least one of the incorrect specs for a national instrument
data acquisition card DAQCard-6024E. This card has only four different
gain settings (+-10V, +-5V, +-0.5V, +-0.05V).
Signed-off-by: Martin Homuth-Rosemann <homuth-rosemann@gmx.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
projects / karo-tx-linux.git / log