Dave Hansen [Mon, 8 Jul 2013 21:44:04 +0000 (14:44 -0700)]
perf/x86: Fix incorrect use of do_div() in NMI warning
I completely botched understanding the calling conventions of
do_div(). I assumed that do_div() returned the result instead
of realizing that it modifies its argument and returns a
remainder. The side-effect from this would be bogus numbers
for the "msecs" value in the warning messages:
INFO: NMI handler (perf_event_nmi_handler) took too long to run: 0.114 msecs
Note, there was a second fix posted by Stephane Eranian for
a separate patch which I also botched:
Peter Zijlstra [Fri, 28 Jun 2013 09:18:53 +0000 (11:18 +0200)]
sched: Fix HRTICK
David reported that the HRTICK sched feature was borken; which was enough
motivation for me to finally fix it ;-)
We should not allow hrtimer code to do softirq wakeups while holding scheduler
locks. The hrtimer code only needs this when we accidentally try to program an
expired time. We don't much care about those anyway since we have the regular
tick to fall back to.
Stephen Boyd [Thu, 11 Jul 2013 14:00:59 +0000 (07:00 -0700)]
tick: broadcast: Check broadcast mode on CPU hotplug
On ARM systems the dummy clockevent is registered with the cpu
hotplug notifier chain before any other per-cpu clockevent. This
has the side-effect of causing the dummy clockevent to be
registered first in every hotplug sequence. Because the dummy is
first, we'll try to turn the broadcast source on but the code in
tick_device_uses_broadcast() assumes the broadcast source is in
periodic mode and calls tick_broadcast_start_periodic()
unconditionally.
On boot this isn't a problem because we typically haven't
switched into oneshot mode yet (if at all). During hotplug, if
the broadcast source isn't in periodic mode we'll replace the
broadcast oneshot handler with the broadcast periodic handler and
start emulating oneshot mode when we shouldn't. Due to the way
the broadcast oneshot handler programs the next_event it's
possible for it to contain KTIME_MAX and cause us to hang the
system when the periodic handler tries to program the next tick.
Fix this by using the appropriate function to start the broadcast
source.
Reported-by: Stephen Warren <swarren@nvidia.com> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Cc: Mark Rutland <Mark.Rutland@arm.com> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: ARM kernel mailing list <linux-arm-kernel@lists.infradead.org> Cc: John Stultz <john.stultz@linaro.org> Cc: Joseph Lo <josephl@nvidia.com> Link: http://lkml.kernel.org/r/20130711140059.GA27430@codeaurora.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Peter Zijlstra [Fri, 12 Jul 2013 09:08:33 +0000 (11:08 +0200)]
perf: Fix perf_lock_task_context() vs RCU
Jiri managed to trigger this warning:
[] ======================================================
[] [ INFO: possible circular locking dependency detected ]
[] 3.10.0+ #228 Tainted: G W
[] -------------------------------------------------------
[] p/6613 is trying to acquire lock:
[] (rcu_node_0){..-...}, at: [<ffffffff810ca797>] rcu_read_unlock_special+0xa7/0x250
[]
[] but task is already holding lock:
[] (&ctx->lock){-.-...}, at: [<ffffffff810f2879>] perf_lock_task_context+0xd9/0x2c0
[]
[] which lock already depends on the new lock.
[]
[] the existing dependency chain (in reverse order) is:
[]
[] -> #4 (&ctx->lock){-.-...}:
[] -> #3 (&rq->lock){-.-.-.}:
[] -> #2 (&p->pi_lock){-.-.-.}:
[] -> #1 (&rnp->nocb_gp_wq[1]){......}:
[] -> #0 (rcu_node_0){..-...}:
Paul was quick to explain that due to preemptible RCU we cannot call
rcu_read_unlock() while holding scheduler (or nested) locks when part
of the read side critical section was preemptible.
Therefore solve it by making the entire RCU read side non-preemptible.
Also pull out the retry from under the non-preempt to play nice with RT.
Reported-by: Jiri Olsa <jolsa@redhat.com> Helped-out-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: <stable@kernel.org> Signed-off-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Ingo Molnar <mingo@kernel.org>
Jiri Olsa [Tue, 9 Jul 2013 15:44:11 +0000 (17:44 +0200)]
perf: Remove WARN_ON_ONCE() check in __perf_event_enable() for valid scenario
The '!ctx->is_active' check has a valid scenario, so
there's no need for the warning.
The reason is that there's a time window between the
'ctx->is_active' check in the perf_event_enable() function
and the __perf_event_enable() function having:
- IRQs on
- ctx->lock unlocked
where the task could be killed and 'ctx' deactivated by
perf_event_exit_task(), ending up with the warning below.
So remove the WARN_ON_ONCE() check and add comments to
explain it all.
This addresses the following warning reported by Vince Weaver:
Jiri Olsa [Tue, 9 Jul 2013 15:44:10 +0000 (17:44 +0200)]
perf: Clone child context from parent context pmu
Currently when the child context for inherited events is
created, it's based on the pmu object of the first event
of the parent context.
This is wrong for the following scenario:
- HW context having HW and SW event
- HW event got removed (closed)
- SW event stays in HW context as the only event
and its pmu is used to clone the child context
The issue starts when the cpu context object is touched
based on the pmu context object (__get_cpu_context). In
this case the HW context will work with SW cpu context
ending up with following WARN below.
Fixing this by using parent context pmu object to clone
from child context.
Addresses the following warning reported by Vince Weaver:
Wolfram Sang [Wed, 10 Jul 2013 15:57:44 +0000 (16:57 +0100)]
drivers/net/ieee802154: don't use devm_pinctrl_get_select_default() in probe
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for setting the default pins. Compile tested only.
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13) Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Wolfram Sang [Wed, 10 Jul 2013 15:57:43 +0000 (16:57 +0100)]
drivers/net/ethernet/cadence: don't use devm_pinctrl_get_select_default() in probe
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for setting the default pins. Compile tested only.
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13) Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wolfram Sang [Wed, 10 Jul 2013 15:57:42 +0000 (16:57 +0100)]
drivers/net/can/c_can: don't use devm_pinctrl_get_select_default() in probe
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for setting the default pins. Compile tested only.
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13) Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Base on cdc_ether, add the mii functions for RTL8152 and RTL8153.
The RTL8152 and RTL8153 support ECM mode which use the driver of
cdc_ether. Add the mii functions. Then, the basic PHY access is
possible.
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 10 Jul 2013 10:58:59 +0000 (13:58 +0300)]
mlx5: Return -EFAULT instead of -EPERM
For copy_to/from_user() failure, the correct error code is -EFAULT not
-EPERM.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
Dean Luick [Thu, 11 Jul 2013 19:32:14 +0000 (15:32 -0400)]
IB/qib: Log all SDMA errors unconditionally
This patch adds code to log SDMA errors for supportability purposes.
Signed-off-by: Dean Luick <dean.luick@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
The vzalloc()'ed field physshadow is leaked on module unload.
This patch adds vfree after the sibling page shadow is freed.
Reported-by: Dean Luick <dean.luick@intel.com> Reviewed-by: Dean Luick <dean.luick@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
mlx5_core: Adjust hca_cap.uar_page_sz to conform to Connect-IB spec
Sparse reported an endianness bug in the assignment to hca_cap.uar_page_sz.
Fix the declaration of this field to be __be16 (which is what is in
the firmware spec), renaming the field to log_uar_pg_size to conform
to the spec, which fixes the endianness bug reported by sparse.
Reported-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Moshe Lazer <moshel@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
IB/srp: Let srp_abort() return FAST_IO_FAIL if TL offline
If the transport layer is offline it is more appropriate to let
srp_abort() return FAST_IO_FAIL instead of SUCCESS.
Reported-by: Sebastian Riemer <sebastian.riemer@profitbricks.com> Acked-by: David Dillow <dillowda@ornl.gov> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Roland Dreier <roland@purestorage.com>
Alexander Duyck [Thu, 11 Jul 2013 20:12:22 +0000 (13:12 -0700)]
gre: Fix MTU sizing check for gretap tunnels
This change fixes an MTU sizing issue seen with gretap tunnels when non-gso
packets are sent from the interface.
In my case I was able to reproduce the issue by simply sending a ping of
1421 bytes with the gretap interface created on a device with a standard
1500 mtu.
This fix is based on the fact that the tunnel mtu is already adjusted by
dev->hard_header_len so it would make sense that any packets being compared
against that mtu should also be adjusted by hard_header_len and the tunnel
header instead of just the tunnel header.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Reported-by: Cong Wang <amwang@redhat.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Shilovsky [Thu, 11 Jul 2013 07:17:45 +0000 (11:17 +0400)]
CIFS: Fix a deadlock when a file is reopened
If we request reading or writing on a file that needs to be
reopened, it causes the deadlock: we are already holding rw
semaphore for reading and then we try to acquire it for writing
in cifs_relock_file. Fix this by acquiring the semaphore for
reading in cifs_relock_file due to we don't make any changes in
locks and don't need a write access.
CC: <stable@vger.kernel.org> Signed-off-by: Pavel Shilovsky <pshilovsky@samba.org> Acked-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com>
Pavel Shilovsky [Thu, 11 Jul 2013 06:58:30 +0000 (10:58 +0400)]
CIFS: Reopen the file if reconnect durable handle failed
This is a follow-on patch for 8/8 patch from the durable handles
series. It fixes the problem when durable file handle timeout
expired on the server and reopen returns -ENOENT for such files. Signed-off-by: Pavel Shilovsky <pshilovsky@samba.org> Signed-off-by: Steve French <smfrench@gmail.com>
xfs: Fix the logic check for all quotas being turned off
During the review of seperate pquota inode patches, David noticed
that the test to detect all quotas being turned off was
incorrect, and hence the block was not freeing all the quota
information.
The check made sense in Irix, but in Linux, quota is turned off
one at a time, which makes the test invalid for Linux.
This problem existed since XFS was ported to Linux.
David suggested to fix the problem by detecting when all quotas are
turned off by checking m_qflags.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com> Reviewed-by: Ben Myers <bpm@sgi.com> Signed-off-by: Ben Myers <bpm@sgi.com>
This patch is being created to use the UEFI bits in the type 219 SMBIOS
record in order to decide whether or not to execute BIOS code. This is a
better solution than to depend on the iCRU bit since not all future servers
will use iCRU.
In watchdog_ping(), 'start' is called automatically when 'ping' function call
is not configured.
Softdog driver has same handling in both cases - start and ping, so 'ping' OPS
can be removed.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
watchdog: New watchdog driver for MEN A21 watchdogs
This patch adds the driver for the watchdog devices found on MEN Mikro
Elektronik A21 VMEbus CPU Carrier Boards. It has DT-support and uses the
watchdog framework.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@men.de> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Russell King [Tue, 18 Jun 2013 16:20:32 +0000 (17:20 +0100)]
Watchdog: fix clearing of the watchdog interrupt
The bits in BRIDGE_CAUSE are documented as RW0C - read, write 0 to
clear. If we read the register, mask off the watchdog bit, and
write it back, we're actually clearing every interrupt which wasn't
pending at the time we read the register - and that is racy.
Fix this to only write ~WATCHDOG_BIT to the register, which means
we write as zero only the watchdog bit.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Acked-by: Jason Cooper <jason@lakedaemon.net> Tested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Russell King [Tue, 18 Jun 2013 16:19:32 +0000 (17:19 +0100)]
Watchdog: allow orion_wdt to be built for Dove
The watchdog infrastructure in Dove is no different from that in
Orion5x or Kirkwood, so let's enable it for Dove. The only things
missing are a few register settings in Dove's bridge-regs.h.
Rather than duplicating the same register bit masks for the RSTOUTn_MASK
and BRIDGE_CAUSE registers, move the definitions into the watchdog
driver itself.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Acked-by: Jason Cooper <jason@lakedaemon.net> Tested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Merge tag 'dm-3.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull device-mapper changes from Alasdair G Kergon:
"Add a device-mapper target called dm-switch to provide a multipath
framework for storage arrays that dynamically reconfigure their
preferred paths for different device regions.
Fix a bug in the verity target that prevented its use with some
specific sizes of devices.
Improve some locking mechanisms in the device-mapper core and bufio.
Add Mike Snitzer as a device-mapper maintainer.
A few more clean-ups and fixes"
* tag 'dm-3.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm: add switch target
dm: update maintainers
dm: optimize reorder structure
dm: optimize use SRCU and RCU
dm bufio: submit writes outside lock
dm cache: fix arm link errors with inline
dm verity: use __ffs and __fls
dm flakey: correct ctr alloc failure mesg
dm verity: remove pointless comparison
dm: use __GFP_HIGHMEM in __vmalloc
dm verity: fix inability to use a few specific devices sizes
dm ioctl: set noio flag to avoid __vmalloc deadlock
dm mpath: fix ioctl deadlock when no paths
Merge branch 'for-3.11/core' of git://git.kernel.dk/linux-block
Pull core block IO updates from Jens Axboe:
"Here are the core IO block bits for 3.11. It contains:
- A tweak to the reserved tag logic from Jan, for weirdo devices with
just 3 free tags. But for those it improves things substantially
for random writes.
- Periodic writeback fix from Jan. Marked for stable as well.
- Fix for a race condition in IO scheduler switching from Jianpeng.
- The hierarchical blk-cgroup support from Tejun. This is the grunt
of the series.
- blk-throttle fix from Vivek.
Just a note that I'm in the middle of a relocation, whole family is
flying out tomorrow. Hence I will be awal the remainder of this week,
but back at work again on Monday the 15th. CC'ing Tejun, since any
potential "surprises" will most likely be from the blk-cgroup work.
But it's been brewing for a while and sitting in my tree and
linux-next for a long time, so should be solid."
* 'for-3.11/core' of git://git.kernel.dk/linux-block: (36 commits)
elevator: Fix a race in elevator switching
block: Reserve only one queue tag for sync IO if only 3 tags are available
writeback: Fix periodic writeback after fs mount
blk-throttle: implement proper hierarchy support
blk-throttle: implement throtl_grp->has_rules[]
blk-throttle: Account for child group's start time in parent while bio climbs up
blk-throttle: add throtl_qnode for dispatch fairness
blk-throttle: make throtl_pending_timer_fn() ready for hierarchy
blk-throttle: make tg_dispatch_one_bio() ready for hierarchy
blk-throttle: make blk_throtl_bio() ready for hierarchy
blk-throttle: make blk_throtl_drain() ready for hierarchy
blk-throttle: dispatch from throtl_pending_timer_fn()
blk-throttle: implement dispatch looping
blk-throttle: separate out throtl_service_queue->pending_timer from throtl_data->dispatch_work
blk-throttle: set REQ_THROTTLED from throtl_charge_bio() and gate stats update with it
blk-throttle: implement sq_to_tg(), sq_to_td() and throtl_log()
blk-throttle: add throtl_service_queue->parent_sq
blk-throttle: generalize update_disptime optimization in blk_throtl_bio()
blk-throttle: dispatch to throtl_data->service_queue.bio_lists[]
blk-throttle: move bio_lists[] and friends to throtl_service_queue
...
Paolo Valente [Wed, 10 Jul 2013 13:46:09 +0000 (15:46 +0200)]
pkt_sched: sch_qfq: remove forward declaration of qfq_update_agg_ts
This patch removes the forward declaration of qfq_update_agg_ts, by moving
the definition of the function above its first call. This patch also
removes a useless forward declaration of qfq_schedule_agg.
Reported-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paolo Valente <paolo.valente@unimore.it> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Valente [Wed, 10 Jul 2013 13:46:08 +0000 (15:46 +0200)]
pkt_sched: sch_qfq: improve efficiency of make_eligible
In make_eligible, a mask is used to decide which groups must become eligible:
the i-th group becomes eligible only if the i-th bit of the mask (from the
right) is set. The mask is computed by left-shifting a 1 by a given number of
places, and decrementing the result. The shift is performed on a ULL to avoid
problems in case the number of places to shift is higher than 31. On a 32-bit
machine, this is more costly than working on an UL. This patch replaces such a
costly operation with two cheaper branches.
The trick is based on the following fact: in case of a shift of at least 32
places, the resulting mask has at least the 32 less significant bits set,
whereas the total number of groups is lower than 32. As a consequence, in this
case it is enough to just set the 32 less significant bits of the mask with a
cheaper ~0UL. In the other case, the shift can be safely performed on a UL.
Reported-by: David S. Miller <davem@davemloft.net> Reported-by: David Laight <David.Laight@ACULAB.COM> Signed-off-by: Paolo Valente <paolo.valente@unimore.it> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull SCSI target updates from Nicholas Bellinger:
"Lots of activity this round on performance improvements in target-core
while benchmarking the prototype scsi-mq initiator code with
vhost-scsi fabric ports, along with a number of iscsi/iser-target
improvements and hardening fixes for exception path cases post v3.10
merge.
The highlights include:
- Make persistent reservations APTPL buffer allocated on-demand, and
drop per t10_reservation buffer. (grover)
- Make virtual LUN=0 a NULLIO device, and skip allocation of NULLIO
device pages (grover)
- Add transport_cmd_check_stop write_pending bit to avoid extra
access of ->t_state_lock is WRITE I/O submission fast-path. (nab)
- Drop unnecessary CMD_T_DEV_ACTIVE check from
transport_lun_remove_cmd to avoid extra access of ->t_state_lock in
release fast-path. (nab)
- Avoid extra t_state_lock access in __target_execute_cmd fast-path
(nab)
- Drop unnecessary vhost-scsi wait_for_tasks=true usage +
->t_state_lock access in release fast-path. (nab)
- Convert vhost-scsi to use modern se_cmd->cmd_kref
TARGET_SCF_ACK_KREF usage (nab)
- Add tracepoints for SCSI commands being processed (roland)
- Refactoring of iscsi-target handling of ISCSI_OP_NOOP +
ISCSI_OP_TEXT to be transport independent (nab)
- Add iscsi-target SendTargets=$IQN support for in-band discovery
(nab)
- Add iser-target support for in-band discovery (nab + Or)
- Add iscsi-target demo-mode TPG authentication context support (nab)
- Fix isert_put_reject payload buffer post (nab)
- Fix iscsit_add_reject* usage for iser (nab)
- Fix iscsit_sequence_cmd reject handling for iser (nab)
- Fix ISCSI_OP_SCSI_TMFUNC handling for iser (nab)
- Fix session reset bug with RDMA_CM_EVENT_DISCONNECTED (nab)
The last five iscsi/iser-target items are CC'ed to stable, as they do
address issues present in v3.10 code. They are certainly larger than
I'd like for stable patch set, but are important to ensure proper
REJECT exception handling in iser-target for 3.10.y"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (51 commits)
iser-target: Ignore non TEXT + LOGOUT opcodes for discovery
target: make queue_tm_rsp() return void
target: remove unused codes from enum tcm_tmrsp_table
iscsi-target: kstrtou* configfs attribute parameter cleanups
iscsi-target: Fix tfc_tpg_auth_cit configfs length overflow
iscsi-target: Fix tfc_tpg_nacl_auth_cit configfs length overflow
iser-target: Add support for ISCSI_OP_TEXT opcode + payload handling
iser-target: Rename sense_buf_[dma,len] to pdu_[dma,len]
iser-target: Add vendor_err debug output
target: Add (obsolete) checking for PMI/LBA fields in READ CAPACITY(10)
target: Return correct sense data for IO past the end of a device
target: Add tracepoints for SCSI commands being processed
iser-target: Fix session reset bug with RDMA_CM_EVENT_DISCONNECTED
iscsi-target: Fix ISCSI_OP_SCSI_TMFUNC handling for iser
iscsi-target: Fix iscsit_sequence_cmd reject handling for iser
iscsi-target: Fix iscsit_add_reject* usage for iser
iser-target: Fix isert_put_reject payload buffer post
iscsi-target: missing kfree() on error path
iscsi-target: Drop left-over iscsi_conn->bad_hdr
target: Make core_scsi3_update_and_write_aptpl return sense_reason_t
...
Viresh Kumar [Wed, 19 Jun 2013 15:08:58 +0000 (20:38 +0530)]
watchdog: delete mpcore_wdt driver
Interrupt request doesn't use the right API: The TWD watchdog uses a per-cpu
interrupt (usually interrupt #30), and the GIC configuration should flag it as
such. With this setup, request_irq() should fail, and the right API is
request_percpu_irq(), together with enable_percpu_irq()/disable_percpu_irq().
Nothing ensures the userspace ioctl() will end-up kicking the watchdog on the
right CPU.
There are no users of this driver since a long time and it makes more sense to
get rid of it as nobody is looking to fix it.
In case somebody wakes up after this has been removed and needs it, please
revert this driver and pick these updates (These were never pushed to mainline):
Merge tag 'remoteproc-3.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/remoteproc
Pull remoteproc fixes from Ohad Ben-Cohen:
"Trivial remoteproc fixes by Suman Anna, Wei Yongjun and Thomas Meyer"
* tag 'remoteproc-3.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/remoteproc:
remoteproc: Cocci spatch "memdup.spatch"
remoteproc: free carveout memories only after unmapping them
remoteproc/omap: fix a sparse warning
remoteproc: fix checkpatch errors in remoteproc code
remoteproc: fix error return code in rproc_fw_boot()
Merge tag 'pm+acpi-3.11-rc1-more' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management and ACPI updates from Rafael Wysocki:
- Fix for a recent cpufreq regression that caused WARN() to trigger
overzealously in a couple of places and spam the kernel log with
useless garbage as a result. From Viresh Kumar.
- ACPI dock fix removing a discrepancy between the definition of
acpi_dock_init(), which says that the function returns int, and its
header in the header file, which says that it is a void function.
The function is now defined as void too.
- ACPI PM fix for failures to update device power states as needed, for
example, during resume from system suspend, because the old state was
deeper than the new one, but the new one is not D0.
- Fix for two debug messages in the ACPI power resources code that
don't have a newline at the end and make the kernel log difficult to
read. From Mika Westerberg.
- Two ACPI cleanups from Naresh Bhat and Haicheng Li.
- cpupower updates from Thomas Renninger, including Intel Haswell
support improvements and a new idle-set subcommand among other
things.
* tag 'pm+acpi-3.11-rc1-more' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / power: add missing newline to debug messages
cpupower: Add Haswell family 0x45 specific idle monitor to show PC8,9,10 states
cpupower: Haswell also supports the C-states introduced with SandyBridge
cpupower: Introduce idle-set subcommand and C-state enabling/disabling
cpupower: Implement disabling of cstate interface
cpupower: Make idlestate usage unsigned
ACPI / fan: Initialize acpi_state variable
ACPI / scan: remove unused LIST_HEAD(acpi_device_list)
ACPI / dock: Actually define acpi_dock_init() as void
ACPI / PM: Fix corner case in acpi_bus_update_power()
cpufreq: Fix serialization of frequency transitions
Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management updates from Zhang Rui:
"There are not too many changes this time, except two new platform
thermal drivers, ti-soc-thermal driver and x86_pkg_temp_thermal
driver, and a couple of small fixes.
Highlights:
- move the ti-soc-thermal driver out of the staging tree to the
thermal tree.
- introduce the x86_pkg_temp_thermal driver. This driver registers
CPU digital temperature package level sensor as a thermal zone.
- small fixes/cleanups including removing redundant use of
platform_set_drvdata() and of_match_ptr for all platform thermal
drivers"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (34 commits)
thermal: cpu_cooling: fix stub function
thermal: ti-soc-thermal: use standard GPIO DT bindings
thermal: MAINTAINERS: Add git tree path for SoC specific updates
thermal: fix x86_pkg_temp_thermal.c build and Kconfig
Thermal: Documentation for x86 package temperature thermal driver
Thermal: CPU Package temperature thermal
thermal: consider emul_temperature while computing trend
thermal: ti-soc-thermal: add DT example for DRA752 chip
thermal: ti-soc-thermal: add dra752 chip to device table
thermal: ti-soc-thermal: add thermal data for DRA752 chips
thermal: ti-soc-thermal: remove usage of IS_ERR_OR_NULL
thermal: ti-soc-thermal: freeze FSM while computing trend
thermal: ti-soc-thermal: remove external heat while extrapolating hotspot
thermal: ti-soc-thermal: update DT reference for OMAP5430
x86, mcheck, therm_throt: Process package thresholds
thermal: cpu_cooling: fix 'descend' check in get_property()
Thermal: spear: Remove redundant use of of_match_ptr
Thermal: kirkwood: Remove redundant use of of_match_ptr
Thermal: dove: Remove redundant use of of_match_ptr
Thermal: armada: Remove redundant use of of_match_ptr
...
Alexander Duyck [Thu, 11 Jul 2013 00:05:06 +0000 (17:05 -0700)]
gso: Update tunnel segmentation to support Tx checksum offload
This change makes it so that the GRE and VXLAN tunnels can make use of Tx
checksum offload support provided by some drivers via the hw_enc_features.
Without this fix enabling GSO means sacrificing Tx checksum offload and
this actually leads to a performance regression as shown below:
Utilization
Send
Throughput local GSO
10^6bits/s % S state
6276.51 8.39 enabled
7123.52 8.42 disabled
To resolve this it was necessary to address two items. First
netif_skb_features needed to be updated so that it would correctly handle
the Trans Ether Bridging protocol without impacting the need to check for
Q-in-Q tagging. To do this it was necessary to update harmonize_features
so that it used skb_network_protocol instead of just using the outer
protocol.
Second it was necessary to update the GRE and UDP tunnel segmentation
offloads so that they would reset the encapsulation bit and inner header
offsets after the offload was complete.
As a result of this change I have seen the following results on a interface
with Tx checksum enabled for encapsulated frames:
Utilization
Send
Throughput local GSO
10^6bits/s % S state
7123.52 8.42 disabled
8321.75 5.43 enabled
v2: Instead of replacing refrence to skb->protocol with
skb_network_protocol just replace the protocol reference in
harmonize_features to allow for double VLAN tag checks.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
watchdog: core: don't try to stop device if not running
A watchdog device may be stopped from userspace using WDIOC_SETOPTIONS
ioctl and flag WDIOS_DISABLECARD. If the device is closed after this
operation, watchdog_release() is called and status bits checked for
stopping it. Besides, if the device has not been unregistered a critical
message "watchdog did not stop!" is printed, although the ioctl may have
successfully stopped it already.
Without the patch a user application sample code like this will successfully
stop the watchdog, but the kernel will output the message
"watchdog did not stop!":
Merge tag 'nfs-for-3.11-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull second set of NFS client updates from Trond Myklebust:
"This mainly contains some small readdir optimisations that had
dependencies on Al Viro's readdir rewrite. There is also a fix for a
nasty deadlock which surfaced earlier in this merge window.
Highlights include:
- Fix an_rpc pipefs regression that causes a deadlock on mount
- Readdir optimisations by Scott Mayhew and Jeff Layton
- clean up the rpc_pipefs dentry operation setup"
* tag 'nfs-for-3.11-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
SUNRPC: Fix a deadlock in rpc_client_register()
rpc_pipe: rpc_dir_inode_operations can be static
NFS: Allow nfs_updatepage to extend a write under additional circumstances
NFS: Make nfs_readdir revalidate less often
NFS: Make nfs_attribute_cache_expired() non-static
rpc_pipe: set dentry operations at d_alloc time
nfs: set verifier on existing dentries in nfs_prime_dcache
Jingoo Han [Thu, 23 May 2013 10:44:23 +0000 (19:44 +0900)]
watchdog: da9055: use platform_{get,set}_drvdata()
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Jingoo Han [Thu, 23 May 2013 10:44:09 +0000 (19:44 +0900)]
watchdog: da9052: use platform_{get,set}_drvdata()
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Jingoo Han [Thu, 23 May 2013 10:43:43 +0000 (19:43 +0900)]
watchdog: cpwd: use platform_{get,set}_drvdata()
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Jingoo Han [Thu, 23 May 2013 10:44:53 +0000 (19:44 +0900)]
watchdog: wm831x: use platform_{get,set}_drvdata()
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The reason is that when loading dummy, if __rtnl_link_register() return failed,
the init_module should return and avoid take the wrong path.
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com> Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jingoo Han [Thu, 23 May 2013 10:44:38 +0000 (19:44 +0900)]
watchdog: riowd: use platform_{get,set}_drvdata()
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
ipv6: fix route selection if kernel is not compiled with CONFIG_IPV6_ROUTER_PREF
This is a follow-up patch to 3630d40067a21d4dfbadc6002bb469ce26ac5d52
("ipv6: rt6_check_neigh should successfully verify neigh if no NUD
information are available").
Since the removal of rt->n in rt6_info we can end up with a dst ==
NULL in rt6_check_neigh. In case the kernel is not compiled with
CONFIG_IPV6_ROUTER_PREF we should also select a route with unkown
NUD state but we must not avoid doing round robin selection on routes
with the same target. So introduce and pass down a boolean ``do_rr'' to
indicate when we should update rt->rr_ptr. As soon as no route is valid
we do backtracking and do a lookup on a higher level in the fib trie.
v2:
a) Improved rt6_check_neigh logic (no need to create neighbour there)
and documented return values.
v3:
a) Introduce enum rt6_nud_state to get rid of the magic numbers
(thanks to David Miller).
b) Update and shorten commit message a bit to actualy reflect
the source.
Reported-by: Pierre Emeriaud <petrus.lt@gmail.com> Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit c957d09ffda417f6c8e3d1f10e2b05228607d6d7
"bnx2x: Remove sparse and coccinelle warnings"
driver provided wrong partial csum for HW in tunneing
scenarios.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Alexander Duyck <alexander.h.duyck@intel.com> CC: Pravin Shelar <pshelar@nicira.com> CC: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Tested-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
vxlan exit module unregisters vxlan net and then it unregisters
rtnl ops which triggers vxlan_dellink() from __rtnl_kill_links().
vxlan_dellink() deletes vxlan-dev from vxlan_list which has
list-head in vxlan-net-struct but that is already gone due to
net-unregister. That is how we are getting following crash.
Following commit fixes the crash by fixing module exit path.
Merge tag 'for-linus-3.11-merge-window-part-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs
Pull second round of 9p patches from Eric Van Hensbergen:
"Several of these patches were rebased in order to correct style
issues. Only stylistic changes were made versus the patches which
were in linux-next for two weeks. The rebases have been in linux-next
for 3 days and have passed my regressions.
The bulk of these are RDMA fixes and improvements. There's also some
additions on the extended attributes front to support some additional
namespaces and a new option for TCP to force allocation of mount
requests from a priviledged port"
* tag 'for-linus-3.11-merge-window-part-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
fs/9p: Remove the unused variable "err" in v9fs_vfs_getattr()
9P: Add cancelled() to the transport functions.
9P/RDMA: count posted buffers without a pending request
9P/RDMA: Improve error handling in rdma_request
9P/RDMA: Do not free req->rc in error handling in rdma_request()
9P/RDMA: Use a semaphore to protect the RQ
9P/RDMA: Protect against duplicate replies
9P/RDMA: increase P9_RDMA_MAXSIZE to 1MB
9pnet: refactor struct p9_fcall alloc code
9P/RDMA: rdma_request() needs not allocate req->rc
9P: Fix fcall allocation for rdma
fs/9p: xattr: add trusted and security namespaces
net/9p: add privport option to 9p tcp transport
Merge tag 'ecryptfs-3.11-rc1-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs
Pull eCryptfs updates from Tyler Hicks:
"Code cleanups and improved buffer handling during page crypto
operations:
- Remove redundant code by merging some encrypt and decrypt functions
- Get rid of a helper page allocation during page decryption by using
in-place decryption
- Better use of entire pages during page crypto operations
- Several code cleanups"
* tag 'ecryptfs-3.11-rc1-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
Use ecryptfs_dentry_to_lower_path in a couple of places
eCryptfs: Make extent and scatterlist crypt function parameters similar
eCryptfs: Collapse crypt_page_offset() into crypt_extent()
eCryptfs: Merge ecryptfs_encrypt_extent() and ecryptfs_decrypt_extent()
eCryptfs: Combine page_offset crypto functions
eCryptfs: Combine encrypt_scatterlist() and decrypt_scatterlist()
eCryptfs: Decrypt pages in-place
eCryptfs: Accept one offset parameter in page offset crypto functions
eCryptfs: Simplify lower file offset calculation
eCryptfs: Read/write entire page during page IO
eCryptfs: Use entire helper page during page crypto operations
eCryptfs: Cocci spatch "memdup.spatch"
Merge branch 'for-3.11' of git://linux-nfs.org/~bfields/linux
Pull nfsd changes from Bruce Fields:
"Changes this time include:
- 4.1 enabled on the server by default: the last 4.1-specific issues
I know of are fixed, so we're not going to find the rest of the
bugs without more exposure.
- Experimental support for NFSv4.2 MAC Labeling (to allow running
selinux over NFS), from Dave Quigley.
- Fixes for some delicate cache/upcall races that could cause rare
server hangs; thanks to Neil Brown and Bodo Stroesser for extreme
debugging persistence.
- Fixes for some bugs found at the recent NFS bakeathon, mostly v4
and v4.1-specific, but also a generic bug handling fragmented rpc
calls"
* 'for-3.11' of git://linux-nfs.org/~bfields/linux: (31 commits)
nfsd4: support minorversion 1 by default
nfsd4: allow destroy_session over destroyed session
svcrpc: fix failures to handle -1 uid's
sunrpc: Don't schedule an upcall on a replaced cache entry.
net/sunrpc: xpt_auth_cache should be ignored when expired.
sunrpc/cache: ensure items removed from cache do not have pending upcalls.
sunrpc/cache: use cache_fresh_unlocked consistently and correctly.
sunrpc/cache: remove races with queuing an upcall.
nfsd4: return delegation immediately if lease fails
nfsd4: do not throw away 4.1 lock state on last unlock
nfsd4: delegation-based open reclaims should bypass permissions
svcrpc: don't error out on small tcp fragment
svcrpc: fix handling of too-short rpc's
nfsd4: minor read_buf cleanup
nfsd4: fix decoding of compounds across page boundaries
nfsd4: clean up nfs4_open_delegation
NFSD: Don't give out read delegations on creates
nfsd4: allow client to send no cb_sec flavors
nfsd4: fail attempts to request gss on the backchannel
nfsd4: implement minimal SP4_MACH_CRED
...
Merge tag 'trace-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing changes from Steven Rostedt:
"The majority of the changes here are cleanups for the large changes
that were added to 3.10, which includes several bug fixes that have
been marked for stable.
As for new features, there were a few, but nothing to write to LWN
about. These include:
New function trigger called "dump" and "cpudump" that will cause
ftrace to dump its buffer to the console when the function is called.
The difference between "dump" and "cpudump" is that "dump" will dump
the entire contents of the ftrace buffer, where as "cpudump" will only
dump the contents of the ftrace buffer for the CPU that called the
function.
Another small enhancement is a new sysctl switch called
"traceoff_on_warning" which, when enabled, will disable tracing if any
WARN_ON() is triggered. This is useful if you want to debug what
caused a warning and do not want to risk losing your trace data by the
ring buffer overwriting the data before you can disable it. There's
also a kernel command line option that will make this enabled at boot
up called the same thing"
* tag 'trace-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (34 commits)
tracing: Make tracing_open_generic_{tr,tc}() static
tracing: Remove ftrace() function
tracing: Remove TRACE_EVENT_TYPE enum definition
tracing: Make tracer_tracing_{off,on,is_on}() static
tracing: Fix irqs-off tag display in syscall tracing
uprobes: Fix return value in error handling path
tracing: Fix race between deleting buffer and setting events
tracing: Add trace_array_get/put() to event handling
tracing: Get trace_array ref counts when accessing trace files
tracing: Add trace_array_get/put() to handle instance refs better
tracing: Protect ftrace_trace_arrays list in trace_events.c
tracing: Make trace_marker use the correct per-instance buffer
ftrace: Do not run selftest if command line parameter is set
tracing/kprobes: Don't pass addr=ip to perf_trace_buf_submit()
tracing: Use flag buffer_disabled for irqsoff tracer
tracing/kprobes: Turn trace_probe->files into list_head
tracing: Fix disabling of soft disable
tracing: Add missing syscall_metadata comment
tracing: Simplify code for showing of soft disabled flag
tracing/kprobes: Kill probe_enable_lock
...
Add project quota changes to all the places where group quota field
is used:
* add separate project quota members into various structures
* split project quota and group quotas so that instead of overriding
the group quota members incore, the new project quota members are
used instead
* get rid of usage of the OQUOTA flag incore, in favor of separate
group and project quota flags.
* add a project dquot argument to various functions.
Not using the pquotino field from superblock yet.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com> Reviewed-by: Ben Myers <bpm@sgi.com> Signed-off-by: Ben Myers <bpm@sgi.com>
drivers/built-in.o: In function `sh_eth_free_dma_buffer':
drivers/net/ethernet/renesas/sh_eth.c:1103: undefined reference to `dma_free_coherent'
drivers/net/ethernet/renesas/sh_eth.c:1110: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `sh_eth_ring_init':
drivers/net/ethernet/renesas/sh_eth.c:1065: undefined reference to `dma_alloc_coherent'
drivers/net/ethernet/renesas/sh_eth.c:1086: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `sh_eth_ring_format':
drivers/net/ethernet/renesas/sh_eth.c:988: undefined reference to `dma_map_single'
drivers/built-in.o: In function `sh_eth_txfree':
drivers/net/ethernet/renesas/sh_eth.c:1220: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `sh_eth_rx':
drivers/net/ethernet/renesas/sh_eth.c:1323: undefined reference to `dma_map_single'
drivers/built-in.o: In function `sh_eth_start_xmit':
drivers/net/ethernet/renesas/sh_eth.c:1954: undefined reference to `dma_map_single'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6: in case of link failure remove route directly instead of letting it expire
We could end up expiring a route which is part of an ecmp route set. Doing
so would invalidate the rt->rt6i_nsiblings calculations and could provoke
the following panic:
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com> Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
It is completely and utterly broken. Module install should not build
any files, and adding broken dependencies to "help" it build files is
complete and utter sh*t.
The kernel should not be built by root, and "make install" and "make
module_install" (that for obvious reasons need to be run as root)
absolutely must not build any files. They should only ever copy the
already-built files over.
So having dependencies for the install targets is wrong, wrong, wrong.
If you try to install a kernel without building it first, you *should*
get errors. The build system shouldn't try to help root build the files.
Jason Wang [Wed, 10 Jul 2013 05:43:28 +0000 (13:43 +0800)]
macvtap: correctly linearize skb when zerocopy is used
Userspace may produce vectors greater than MAX_SKB_FRAGS. When we try to
linearize parts of the skb to let the rest of iov to be fit in
the frags, we need count copylen into linear when calling macvtap_alloc_skb()
instead of partly counting it into data_len. Since this breaks
zerocopy_sg_from_iovec() since its inner counter assumes nr_frags should
be zero at beginning. This cause nr_frags to be increased wrongly without
setting the correct frags.
Cc: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Wed, 10 Jul 2013 05:43:27 +0000 (13:43 +0800)]
tuntap: correctly linearize skb when zerocopy is used
Userspace may produce vectors greater than MAX_SKB_FRAGS. When we try to
linearize parts of the skb to let the rest of iov to be fit in
the frags, we need count copylen into linear when calling tun_alloc_skb()
instead of partly counting it into data_len. Since this breaks
zerocopy_sg_from_iovec() since its inner counter assumes nr_frags should
be zero at beginning. This cause nr_frags to be increased wrongly without
setting the correct frags.
Cc: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'kvm-3.11-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull more KVM changes from Gleb Natapov:
"A fix for a bug that prevents some guests from working on old Intel
CPUs and a patch that integrates ARM64 KVM, merged via ARM64 tree,
into Kconfig."
* tag 'kvm-3.11-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: VMX: mark unusable segment as nonpresent
arm64: KVM: Kconfig integration
Pull Sparc bugfixes from David Miller:
"Four bug fixes:
1) Enable snoop tags properly on Sparc32/LEON, from Andreas Larsson
2) strcpy() length check fix from Chen Gang.
3) Forgotten unregister_netdev() in sunvnet driver, from Dave
Kleikamp.
4) Fix broken assembler offsets used in vm_area_struct accesses on
sparc32, from Olivier DANET."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
[PATCH] sparc32: vm_area_struct access for old Sun SPARCs.
sunvnet: vnet_port_remove must call unregister_netdev
sparc32, leon: Require separate snoop tags set to regard snooping to be enabled
arch: sparc: kernel: check the memory length before use strcpy().
Pull IDE updates from David Miller:
"Just a few small things:
1) module_platform_driver_probe() conversions from Jingoo Han.
2) module_pci_driver() conversion from Libo Chen.
3) PIO size calculation fix from Steven J Hill"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide:
ide: Fix IDE PIO size calculation
drivers/ide/delkin_cb: Convert to module_pci_driver
ide: gayle: use module_platform_driver_probe()
ide: tx4939ide: use module_platform_driver_probe()
ide: tx4938ide: use module_platform_driver_probe()