Keerthy [Fri, 7 Aug 2015 05:07:19 +0000 (10:37 +0530)]
ARM: dts: AM4372: Add the am4372-rtc compatible string
am4372-rtc string was already part of dts, introduced to identify
the rtc specific to am4372 family of SoCs. It was removed in one of the
previous patches. Adding back the same with appropriate documentation.
Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Dave Gerlach [Wed, 5 Aug 2015 10:49:46 +0000 (16:19 +0530)]
ARM: dts: am437x-gp-evm: Add regulator-always-on and regulator-boot-on for RTC DCDCs
DCDC5 and DCDC6 supply rtc and need to be on for accessing the module.
On A1 revision of the TPS65218, FSEAL bit would be undefined without
coin-cell present which in many cases led to it being set, causing DCDC5
and DCDC6 to stay active, but also leading to unexplained failures when
it was not. On B1 revision, FSEAL is always 0 when no coin-cell is present
so this patch is required on boards with B1 revision to ever work. This
implementation works on boards with either A1 or B1 revision and makes
sure that DCDC5 and DCDC6 always stay active.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Keerthy [Wed, 5 Aug 2015 10:49:45 +0000 (16:19 +0530)]
ARM: dts: AM4372: Reorder the rtc compatible string
Compared to da830-rtc compatibility am3352-rtc is more compatible to
the one in am437x. Hence adding the am3352-rtc compatible to cover the
entire feature set.
The ti,am4372-rtc has no Documentation and not used even in the driver
hence removing it.
Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Roger Quadros [Tue, 4 Aug 2015 15:34:59 +0000 (18:34 +0300)]
ARM: dts: am437x-gp-evm: Add gpio-hog for configuring eMMC/NAND driver
On this board either eMMC or NAND can work based on the level of
spi2_cs0.gpio0_23. Add a gpio-hog to enable configuration of this
pin in the device tree.
Move pinmux for spi2_cs0 (SEL_eMMCorNANDn) out of
NAND node into gpio0 so it is initialized with gpio0.
Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ldo1_reg in addition to being connected to the io lines is also
connected to the card detect line. On card removal, omap_hsmmc
driver does a regulator_disable causing card detect line to be
pulled down. This raises a card insertion interrupt and once the
MMC core detects there is no card inserted, it does a
regulator disable which again raises a card insertion interrupt.
This happens in a loop causing infinite MMC interrupts.
Fix it by making ldo1_reg as always_on.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ldo1_reg in addition to being connected to the io lines is also
connected to the card detect line. On card removal, omap_hsmmc
driver does a regulator_disable causing card detect line to be
pulled down. This raises a card insertion interrupt and once the
MMC core detects there is no card inserted, it does a
regulator disable which again raises a card insertion interrupt.
This happens in a loop causing infinite MMC interrupts.
Fix it by making ldo1_reg as always_on.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
SDMMC Card Detect can be used over default GPIO map.
Reported-by: Yan Liu <yan-liu@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a node for evm_3v3_sd using pcf which feeds on to mmc vdd.
Update mapping for vmmc-supply and vmmc_aux-supply.
evm_3v3_sd supplies to SD card vdd, and ldo1 to sdcard i/o lines.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Fri, 17 Jul 2015 21:08:04 +0000 (16:08 -0500)]
ARM: dts: AM4372: Add the wkup_m3_ipc node
Add the Wakeup M3 IPC device node for the wkup_m3_ipc driver on
AM4372 SoC. This node uses the IPC registers, part of the Control
Module, and is therefore added as a child of the scm node.
Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Fri, 17 Jul 2015 21:08:03 +0000 (16:08 -0500)]
ARM: dts: AM33xx: Add the wkup_m3_ipc node
Add the Wakeup M3 IPC node for the wkup_m3_ipc driver on AM33xx SoCs.
This node uses the IPC registers, part of the Control Module, and is
therefore added as a child of the scm node.
Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Add wl1251 support via pdata-quirks as it's driver lacks DT
support. MMC3 is marked disabled in DT so that MMC3 instance of
hsmmc driver is probed using platform data with special card init
callback.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
- add pandora specific compatible name
- fix mmc2 card detect polarity
- fix mmc1 and mmc2 write protect polarity
- disable write protect pins because of production issue and add an
explanation why they are disabled
- fix NAND partition name to reflect the correct address
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
phyBOARD-WEGA-AM335x represents a direct soldered
combination of a phyCORE-AM335x SoM and carrier board.
Different kind of SoM options can be connected to
the wega carrier board. So we created a separate
wega dtsi file. The final dts contains the actual
SoM on the carrier board.
WEGA carrier board features:
* ETH phy on carrier board: 1x MII
* 1x CAN
* 2x UART
* USB0 (device)
* USB1 (host)
* mSD slot
Signed-off-by: Teresa Remmet <t.remmet@phytec.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
phyCORE-AM335x is a SoM (System on Module) containing
a AM335x SOC. The module can be connected to different
carrier boards.
Some hardware parts are configurable on the phyCORE-AM335x.
So they are disabled on default in this som dtsi file.
They will be enabled in the board dts files, when populated.
* RAM up to 1GiB
* PMIC
* NAND flash up to 1GiB
* Eth PHY on SOM: 1x RMII
* SPI NOR flash 8MiB (optional)
* i2c RTC (optional)
* i2c EEPROM 4kiB (optional)
Signed-off-by: Teresa Remmet <t.remmet@phytec.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap3: correct the format of u16 values for tsc2046 node
In tsc2046 touch driver, the values such as ti,x-min is defined as a u16
value. the driver use API of_property_read_u16() read the value. For these
u16 value, the dts entry should be like:
property = /bits/ 16 <0x5000>;
This describes the property as a u16 value.
Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Peter Ujfalusi [Thu, 2 Jul 2015 14:06:25 +0000 (17:06 +0300)]
ARM: dts: am437x-gp-evm: Rename fixed regulator vmmcsd_fixed to evm_v3_3d
The same regulator is used by other chips on the board. The power path is:
VBAT -> TPS63031 - Enable signal is V1_8D regulator -> V3_3D.
V3_3D is used by SD slot and tlv320aic3106 codec as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Peter Ujfalusi [Thu, 2 Jul 2015 14:06:24 +0000 (17:06 +0300)]
ARM: dts: am437x-gp-evm: Add gpio-hog for configuring the display/audio mux
GPIO5_8 is used as a mux switch between LCD and HDMI displays. This mux
affects audio routing as well since in LCD mode HDMI audio is not possible
and when HDMI is selected analog audio is not working.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Peter Ujfalusi [Thu, 2 Jul 2015 14:06:19 +0000 (17:06 +0300)]
ARM: dts: am43xx-epos-evm: Add gpio-hog for configuring the display/audio mux
GPIO2_1 is used as a mux switch between LCD and HDMI displays. This mux
affects audio routing as well since in LCD mode HDMI audio is not possible
and when HDMI is selected analog audio is not working.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Peter Ujfalusi [Thu, 2 Jul 2015 14:06:18 +0000 (17:06 +0300)]
ARM: dts: am437x-sk-evm: Switch using simple-audio-card for audio support
The sound support consist only Headset output on the board and can be
handled by "simple-audio-card".
Also enable the Line-In route as the board has support for it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Peter Ujfalusi [Thu, 2 Jul 2015 14:06:16 +0000 (17:06 +0300)]
ARM: omap2plus_defconfig: Enable audio related config options
More and more boards are moving to have audio support via simple-card.
At the same time enable options needed for most am335x and am43xx board for
audio support: McASP and TLV320AIC3X codecs.
The later two has been selected by the CONFIG_SND_AM33XX_SOC_EVM option, but
the aim is to convert all boards to use simple card.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
In addition to the regular mux configuration such as mux mode 1,
2 etc, certain pins of DRA7 require to have "virtual mode" also
programmed. This allows for predefined delay characteristics to
be used by the SoC to meet timing characterstics needed for the
interface.
Provide easy to use macro to do the same.
It is important to note that the official TI guidelines recommend
to do as minimal pin reconfiguration beyond the bootloader given
the design of the hardware involved which can result in substantial
glitches which may impair functionality of certain peripherals.
Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Vignesh R [Mon, 22 Jun 2015 09:03:44 +0000 (14:33 +0530)]
ARM: dts: DRA72: switch to cpsw slave0 for ethernet
On DRA72 EVM, cpsw slave1 is muxed with VIN2A, hence switch to cpsw
slave0 for ethernet. Add gpio hog entry to pcf_gpio_21 in order to
select cpsw slave0.
Signed-off-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Fri, 29 May 2015 17:21:52 +0000 (10:21 -0700)]
ARM: dts: Remove L3 compatible value for dm816x
The interconnects on dm816x are like on omap4, so we should use
l3-noc instead of l3-smx. But as the related SoC specific
l3_target_data is still missing from omap_l3_noc let's just
remove the entry for now.
Cc: Brian Hutchinson <b.hutchman@gmail.com> Reported-by: Matthijs van Duin <matthijsvanduin@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Ash Charles [Fri, 12 Jun 2015 20:37:25 +0000 (13:37 -0700)]
ARM: dts: overo: Support PoP NAND
Some Overo COM models include NAND flash in the on-board
package-on-package (PoP) chip. Add this to the base Overo devicetree.
Most commonly, this is 512MB NAND from the Micron MT29C4G96MAZ family
but, as discussed [1], several different sized are possible. To
support different sizes, the last partition should fill to the end of
the chip (i.e. MTDPART_SIZ_FULL).
With thanks to Florian Vaussard for the original patch [2] and Adam Lee for
updating it here.
Adam YH Lee [Fri, 12 Jun 2015 20:37:24 +0000 (13:37 -0700)]
ARM: dts: overo: Enable McBSP2 for all Overo COMs
Both Gumstix Overo and Overo Storm COMs use TWL4030 audio module
connected to the McBSP2. As such, enable the McBSP2 module in the
common device tree file, omap3-overo-base.dtsi, rather than in the
processor-specific device tree files, omap3-overo.dtsi and
omap3-overo-storm.dtsi. This corrects audio on the Storm COMs where
the setting was accidentally missing from the device tree.
Signed-off-by: Ash Charles <ashcharles@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Ash Charles [Fri, 12 Jun 2015 20:37:23 +0000 (13:37 -0700)]
ARM: dts: Add DTS for Gumstix TobiDuo expansion board
The Gumstix "Tobi-Duo" expansion board [1] can be used with either
OMAP3 Overo or Overo Storm COMs. It provides two NICs using LAN9221
chips.
It is necessary to duplicate the interface information for the
second SMSC9221 chip as discussed [2].
Suman Anna [Mon, 13 Jul 2015 17:34:55 +0000 (12:34 -0500)]
ARM: dts: AM4372: Add the wkupm3 rproc node
Add the Wakeup M3 remote processor device node for
the AM4372 SoC. The WkupM3 remote processor is used
to implement and achieve low-power functionality on
the AM33xx & AM43xx SoCs.
This node is added as a child of the recently added
l4_wkup node to reflect its presence within the SoC.
Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Mon, 13 Jul 2015 17:34:54 +0000 (12:34 -0500)]
ARM: dts: AM33xx: Update and move wkup_m3 node to l4 node
The WakeupM3 remote processor device node has been moved to
be a child node of the newly created l4_wkup node, to reflect
its presence properly within the SoC. The node was added
previously before any driver support, it is now updated as
per the wkup_m3_rproc bindings added alongside the driver
support.
Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Dave Gerlach [Mon, 13 Jul 2015 17:34:53 +0000 (12:34 -0500)]
ARM: OMAP2+: Use pdata-quirks for wkup_m3 reset management
Use pdata-quirks to provide platform data required for reset
management during boot and shutdown of the wkup_m3 processor
on both the AM33xx and AM43xx SoCs. The WkupM3 remote processor
is used to implement and achieve low-power functionality on
the AM33xx & AM43xx SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
So the change to test 'crtc_state->base.active' cannot possibly be
correct as-is.
There may be some other minimal fix (like just checking crtc_state for
NULL), but I'm just reverting it now for the rc2 release, and people
like Daniel Vetter who actually know this code will figure out what the
right solution is in the longer term.
Reported-and-bisected-by: Jörg Otte <jrg.otte@gmail.com> Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@intel.com> CC: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull VFS fixes from Al Viro:
"Fixes for this cycle regression in overlayfs and a couple of
long-standing (== all the way back to 2.6.12, at least) bugs"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
freeing unlinked file indefinitely delayed
fix a braino in ovl_d_select_inode()
9p: don't leave a half-initialized inode sitting around
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"A fair number of 4.2 fixes also because Markos opened the flood gates.
- Patch up the math used calculate the location for the page bitmap.
- The FDC (Not what you think, FDC stands for Fast Debug Channel) IRQ
around was causing issues on non-Malta platforms, so move the code
to a Malta specific location.
- A spelling fix replicated through several files.
- Fix to the emulation of an R2 instruction for R6 cores.
- Fix the JR emulation for R6.
- Further patching of mindless 64 bit issues.
- Ensure the kernel won't crash on CPUs with L2 caches with >= 8
ways.
- Use compat_sys_getsockopt for O32 ABI on 64 bit kernels.
- Fix cache flushing for multithreaded cores.
- A build fix"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: O32: Use compat_sys_getsockopt.
MIPS: c-r4k: Extend way_string array
MIPS: Pistachio: Support CDMM & Fast Debug Channel
MIPS: Malta: Make GIC FDC IRQ workaround Malta specific
MIPS: c-r4k: Fix cache flushing for MT cores
Revert "MIPS: Kconfig: Disable SMP/CPS for 64-bit"
MIPS: cps-vec: Use macros for various arithmetics and memory operations
MIPS: kernel: cps-vec: Replace KSEG0 with CKSEG0
MIPS: kernel: cps-vec: Use ta0-ta3 pseudo-registers for 64-bit
MIPS: kernel: cps-vec: Replace mips32r2 ISA level with mips64r2
MIPS: kernel: cps-vec: Replace 'la' macro with PTR_LA
MIPS: kernel: smp-cps: Fix 64-bit compatibility errors due to pointer casting
MIPS: Fix erroneous JR emulation for MIPS R6
MIPS: Fix branch emulation for BLTC and BGEC instructions
MIPS: kernel: traps: Fix broken indentation
MIPS: bootmem: Don't use memory holes for page bitmap
MIPS: O32: Do not handle require 32 bytes from the stack to be readable.
MIPS, CPUFREQ: Fix spelling of Institute.
MIPS: Lemote 2F: Fix build caused by recent mass rename.
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
- the high latency PIT detection fix, which slipped through the cracks
for rc1
- a regression fix for the early printk mechanism
- the x86 part to plug irq/vector related hotplug races
- move the allocation of the espfix pages on cpu hotplug to non atomic
context. The current code triggers a might_sleep() warning.
- a series of KASAN fixes addressing boot crashes and usability
- a trivial typo fix for Kconfig help text
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/kconfig: Fix typo in the CONFIG_CMDLINE_BOOL help text
x86/irq: Retrieve irq data after locking irq_desc
x86/irq: Use proper locking in check_irq_vectors_for_cpu_disable()
x86/irq: Plug irq vector hotplug race
x86/earlyprintk: Allow early_printk() to use console style parameters like '115200n8'
x86/espfix: Init espfix on the boot CPU side
x86/espfix: Add 'cpu' parameter to init_espfix_ap()
x86/kasan: Move KASAN_SHADOW_OFFSET to the arch Kconfig
x86/kasan: Add message about KASAN being initialized
x86/kasan: Fix boot crash on AMD processors
x86/kasan: Flush TLBs after switching CR3
x86/kasan: Fix KASAN shadow region page tables
x86/init: Clear 'init_level4_pgt' earlier
x86/tsc: Let high latency PIT fail fast in quick_pit_calibrate()
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"This update from the timer departement contains:
- A series of patches which address a shortcoming in the tick
broadcast code.
If the broadcast device is not available or an hrtimer emulated
broadcast device, some of the original assumptions lead to boot
failures. I rather plugged all of the corner cases instead of only
addressing the issue reported, so the change got a little larger.
Has been extensivly tested on x86 and arm.
- Get rid of the last holdouts using do_posix_clock_monotonic_gettime()
- A regression fix for the imx clocksource driver
- An update to the new state callbacks mechanism for clockevents.
This is required to simplify the conversion, which will take place
in 4.3"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick/broadcast: Prevent NULL pointer dereference
time: Get rid of do_posix_clock_monotonic_gettime
cris: Replace do_posix_clock_monotonic_gettime()
tick/broadcast: Unbreak CONFIG_GENERIC_CLOCKEVENTS=n build
tick/broadcast: Handle spurious interrupts gracefully
tick/broadcast: Check for hrtimer broadcast active early
tick/broadcast: Return busy when IPI is pending
tick/broadcast: Return busy if periodic mode and hrtimer broadcast
tick/broadcast: Move the check for periodic mode inside state handling
tick/broadcast: Prevent deep idle if no broadcast device available
tick/broadcast: Make idle check independent from mode and config
tick/broadcast: Sanity check the shutdown of the local clock_event
tick/broadcast: Prevent hrtimer recursion
clockevents: Allow set-state callbacks to be optional
clocksource/imx: Define clocksource for mx27
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Thomas Gleixner:
"A single fix for a cpu hotplug race vs. interrupt descriptors:
Prevent irq setup/teardown across the cpu starting/dying parts of cpu
hotplug so that the starting/dying cpu has a stable view of the
descriptor space. This has been an issue for all architectures in the
cpu dying phase, where interrupts are migrated away from the dying
cpu. In the starting phase its mostly a x86 issue vs the vector space
update"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
hotplug: Prevent alloc/free of irq descriptors during cpu up/down
Al Viro [Wed, 8 Jul 2015 01:42:38 +0000 (02:42 +0100)]
freeing unlinked file indefinitely delayed
Normally opening a file, unlinking it and then closing will have
the inode freed upon close() (provided that it's not otherwise busy and
has no remaining links, of course). However, there's one case where that
does *not* happen. Namely, if you open it by fhandle with cold dcache,
then unlink() and close().
In normal case you get d_delete() in unlink(2) notice that dentry
is busy and unhash it; on the final dput() it will be forcibly evicted from
dcache, triggering iput() and inode removal. In this case, though, we end
up with *two* dentries - disconnected (created by open-by-fhandle) and
regular one (used by unlink()). The latter will have its reference to inode
dropped just fine, but the former will not - it's considered hashed (it
is on the ->s_anon list), so it will stay around until the memory pressure
will finally do it in. As the result, we have the final iput() delayed
indefinitely. It's trivial to reproduce -
main()
{
int fd;
union {
struct file_handle f;
char buf[MAX_HANDLE_SZ];
} x;
int m;
x.f.handle_bytes = sizeof(x);
chdir("/root");
mkdir("foo", 0700);
fd = open("foo/bar", O_CREAT | O_RDWR, 0600);
close(fd);
name_to_handle_at(AT_FDCWD, "foo/bar", &x.f, &m, 0);
flush_dcache();
fd = open_by_handle_at(AT_FDCWD, &x.f, O_RDWR);
unlink("foo/bar");
write(fd, buf, sizeof(buf));
system("df ."); /* 20Mb eaten */
close(fd);
system("df ."); /* should've freed those 20Mb */
flush_dcache();
system("df ."); /* should be the same as #2 */
}
will spit out something like
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/root 322023 303843 1131 100% /
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/root 322023 303843 1131 100% /
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/root 322023 283282 21692 93% /
- inode gets freed only when dentry is finally evicted (here we trigger
than by remount; normally it would've happened in response to memory
pressure hell knows when).
Cc: stable@vger.kernel.org # v2.6.38+; earlier ones need s/kill_it/unhash_it/ Acked-by: J. Bruce Fields <bfields@fieldses.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Sun, 12 Jul 2015 14:39:45 +0000 (10:39 -0400)]
fix a braino in ovl_d_select_inode()
when opening a directory we want the overlayfs inode, not one from
the topmost layer.
Reported-By: Andrey Jr. Melnikov <temnota.am@gmail.com> Tested-By: Andrey Jr. Melnikov <temnota.am@gmail.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Merge branch 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/nvdimm
Pull libnvdimm fixes from Dan Williams:
"1) Fixes for a handful of smatch reports (Thanks Dan C.!) and minor
bug fixes (patches 1-6)
2) Correctness fixes to the BLK-mode nvdimm driver (patches 7-10).
Granted these are slightly large for a -rc update. They have been
out for review in one form or another since the end of May and were
deferred from the merge window while we settled on the "PMEM API"
for the PMEM-mode nvdimm driver (ie memremap_pmem, memcpy_to_pmem,
and wmb_pmem).
Now that those apis are merged we implement them in the BLK driver
to guarantee that mmio aperture moves stay ordered with respect to
incoming read/write requests, and that writes are flushed through
those mmio-windows and platform-buffers to be persistent on media.
These pass the sub-system unit tests with the updates to
tools/testing/nvdimm, and have received a successful build-report from
the kbuild robot (468 configs).
With acks from Rafael for the touches to drivers/acpi/"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/nvdimm:
nfit: add support for NVDIMM "latch" flag
nfit: update block I/O path to use PMEM API
tools/testing/nvdimm: add mock acpi_nfit_flush_address entries to nfit_test
tools/testing/nvdimm: fix return code for unimplemented commands
tools/testing/nvdimm: mock ioremap_wt
pmem: add maintainer for include/linux/pmem.h
nfit: fix smatch "use after null check" report
nvdimm: Fix return value of nvdimm_bus_init() if class_create() fails
libnvdimm: smatch cleanups in __nd_ioctl
sparse: fix misplaced __pmem definition
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Mostly slight adjusments for new drivers, but also one core fix for
which finally the dependencies are now available as well"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: Mark instantiated device nodes with OF_POPULATE
i2c: jz4780: Fix return value if probe fails
i2c: xgene-slimpro: Fix missing mbox_free_channel call in probe error path
i2c: I2C_MT65XX should depend on HAS_DMA
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"A fix (revert) for a recent regression in Synaptics driver and a fix
for Elan i2c touchpad driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: synaptics - allocate 3 slots to keep stability in image sensors"
Input: elan_i2c - change the hover event from MT to ST
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A small set of fixes for problems found by smatch in new drivers that
we added this rc and a handful of driver fixes that came in during the
merge window"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
drivers: clk: st: Incorrect register offset used for lock_status
clk: mediatek: mt8173: Fix enabling of critical clocks
drivers: clk: st: Fix mux bit-setting for Cortex A9 clocks
drivers: clk: st: Add CLK_GET_RATE_NOCACHE flag to clocks
drivers: clk: st: Fix flexgen lock init
drivers: clk: st: Fix FSYN channel values
drivers: clk: st: Remove unused code
clk: qcom: Use parent rate when set rate to pixel RCG clock
clk: at91: do not leak resources
clk: stm32: Fix out-by-one error path in the index lookup
clk: iproc: fix bit manipulation arithmetic
clk: iproc: fix memory leak from clock name
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"A bunch of fixes for radeon, intel, omap and one amdkfd fix.
Radeon fixes are all over, but it does fix some cursor corruption
across suspend/resume. i915 should fix the second warn you were
seeing, so let us know if not. omap is a bunch of small fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (28 commits)
drm/radeon: disable vce init on cayman (v2)
drm/amdgpu: fix timeout calculation
drm/radeon: check if BO_VA is set before adding it to the invalidation list
drm/radeon: allways add the VM clear duplicate
Revert "Revert "drm/radeon: dont switch vt on suspend""
drm/radeon: Fold radeon_set_cursor() into radeon_show_cursor()
drm/radeon: unpin cursor BOs on suspend and pin them again on resume (v2)
drm/radeon: Clean up reference counting and pinning of the cursor BOs
drm/amdkfd: validate pdd where it acquired first
Revert "drm/i915: Allocate context objects from stolen"
drm/i915: Declare the swizzling unknown for L-shaped configurations
drm/radeon: fix underflow in r600_cp_dispatch_texture()
drm/radeon: default to 2048 MB GART size on SI+
drm/radeon: fix HDP flushing
drm/radeon: use RCU query for GEM_BUSY syscall
drm/amdgpu: Handle irqs only based on irq ring, not irq status regs.
drm/radeon: Handle irqs only based on irq ring, not irq status regs.
drm/i915: Use crtc_state->active in primary check_plane func
drm/i915: Check crtc->active in intel_crtc_disable_planes
drm/i915: Restore all GGTT VMAs on resume
...
Merge branch 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull selinux fixes from James Morris.
* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
selinux: fix mprotect PROT_EXEC regression caused by mm change
selinux: don't waste ebitmap space when importing NetLabel categories
Merge branch 'for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"This is an assortment of fixes. Most of the commits are from Filipe
(fsync, the inode allocation cache and a few others). Mark kicked in
a series fixing corners in the extent sharing ioctls, and everyone
else fixed up on assorted other problems"
* 'for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix wrong check for btrfs_force_chunk_alloc()
Btrfs: fix warning of bytes_may_use
Btrfs: fix hang when failing to submit bio of directIO
Btrfs: fix a comment in inode.c:evict_inode_truncate_pages()
Btrfs: fix memory corruption on failure to submit bio for direct IO
btrfs: don't update mtime/ctime on deduped inodes
btrfs: allow dedupe of same inode
btrfs: fix deadlock with extent-same and readpage
btrfs: pass unaligned length to btrfs_cmp_data()
Btrfs: fix fsync after truncate when no_holes feature is enabled
Btrfs: fix fsync xattr loss in the fast fsync path
Btrfs: fix fsync data loss after append write
Btrfs: fix crash on close_ctree() if cleaner starts new transaction
Btrfs: fix race between caching kthread and returning inode to inode cache
Btrfs: use kmem_cache_free when freeing entry in inode cache
Btrfs: fix race between balance and unused block group deletion
btrfs: add error handling for scrub_workers_get()
btrfs: cleanup noused initialization of dev in btrfs_end_bio()
btrfs: qgroup: allow user to clear the limitation on qgroup
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Kevin Hilman:
"A fairly random colletion of fixes based on -rc1 for OMAP, sunxi and
prima2 as well as a few arm64-specific DT fixes.
This series also includes a late to support a new Allwinner (sunxi)
SoC, but since it's rather simple and isolated to the
platform-specific code, it's included it for this -rc"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: dts: add device tree for ARM SMM-A53x2 on LogicTile Express 20MG
arm: dts: vexpress: add missing CCI PMU device node to TC2
arm: dts: vexpress: describe all PMUs in TC2 dts
GICv3: Add ITS entry to THUNDER dts
arm64: dts: Add poweroff button device node for APM X-Gene platform
ARM: dts: am4372.dtsi: disable rfbi
ARM: dts: am57xx-beagle-x15: Provide supply for usb2_phy2
ARM: dts: am4372: Add emif node
Revert "ARM: dts: am335x-boneblack: disable RTC-only sleep"
ARM: sunxi: Enable simplefb in the defconfig
ARM: Remove deprecated symbol from defconfig files
ARM: sunxi: Add Machine support for A33
ARM: sunxi: Introduce Allwinner H3 support
Documentation: sunxi: Update Allwinner SoC documentation
ARM: prima2: move to use REGMAP APIs for rtciobrg
ARM: dts: atlas7: add pinctrl and gpio descriptions
ARM: OMAP2+: Remove unnessary return statement from the void function, omap2_show_dma_caps
memory: omap-gpmc: Fix parsing of devices
Thomas Gleixner [Sat, 11 Jul 2015 12:26:34 +0000 (14:26 +0200)]
tick/broadcast: Prevent NULL pointer dereference
Dan reported that the recent changes to the broadcast code introduced
a potential NULL dereference.
Add the proper check.
Fixes: e0454311903d "tick/broadcast: Sanity check the shutdown of the local clock_event" Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Merge branch 'parisc-4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"We have one important patch from Dave Anglin and myself which fixes
PTE/TLB race conditions which caused random segmentation faults on our
debian buildd servers, and one patch from Alex Ivanov which speeds up
the graphical text console on the STI framebuffer driver"
* 'parisc-4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix some PTE/TLB race conditions and optimize __flush_tlb_range based on timing results
stifb: Implement hardware accelerated copyarea
Stephen Smalley [Fri, 10 Jul 2015 13:40:59 +0000 (09:40 -0400)]
selinux: fix mprotect PROT_EXEC regression caused by mm change
commit 66fc13039422ba7df2d01a8ee0873e4ef965b50b ("mm: shmem_zero_setup
skip security check and lockdep conflict with XFS") caused a regression
for SELinux by disabling any SELinux checking of mprotect PROT_EXEC on
shared anonymous mappings. However, even before that regression, the
checking on such mprotect PROT_EXEC calls was inconsistent with the
checking on a mmap PROT_EXEC call for a shared anonymous mapping. On a
mmap, the security hook is passed a NULL file and knows it is dealing
with an anonymous mapping and therefore applies an execmem check and no
file checks. On a mprotect, the security hook is passed a vma with a
non-NULL vm_file (as this was set from the internally-created shmem
file during mmap) and therefore applies the file-based execute check
and no execmem check. Since the aforementioned commit now marks the
shmem zero inode with the S_PRIVATE flag, the file checks are disabled
and we have no checking at all on mprotect PROT_EXEC. Add a test to
the mprotect hook logic for such private inodes, and apply an execmem
check in that case. This makes the mmap and mprotect checking
consistent for shared anonymous mappings, as well as for /dev/zero and
ashmem.
Cc: <stable@vger.kernel.org> # 4.1.x Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by: Paul Moore <pmoore@redhat.com>
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes and clean-up from Catalin Marinas:
- ACPI fix when checking the validity of the GICC MADT subtable
- handle debug exceptions in the el*_inv exception entries
- remove pointless register assignment in two compat syscall wrappers
- unnecessary include path
- defconfig update
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: entry32: remove pointless register assignment
arm64: entry: handle debug exceptions in el*_inv
arm64: Keep the ARM64 Kconfig selects sorted
ACPI / ARM64 : use the new BAD_MADT_GICC_ENTRY macro
ACPI / ARM64: add BAD_MADT_GICC_ENTRY() macro
arm64: defconfig: Add Ceva ahci to the defconfig
arm64: remove another unnecessary libfdt include path
projects / linux-beck.git / log