Move the access control up from the fast paths, which are no longer
universally taken first, up into the caller. This then duplicates some
sanity checking along the slow paths, but is much simpler.
Tracked as CVE-2010-2962.
Reported-by: Kees Cook <kees@ubuntu.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This example file uses the old V4L1 API. It also doesn't use libv4l.
So, it is completely obsolete. A good example already exists at
v4l-utils (v4l2grab.c):
http://git.linuxtv.org/v4l-utils.git
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
When the number of failed devices exceeds the allowed number
we must abort any active parity operations (checks or updates) as they
are no longer meaningful, and can lead to a BUG_ON in
handle_parity_checks6.
Disable the new -Wunused-but-set-variable that was added in gcc 4.6.0
It produces more false positives than useful warnings.
This can still be enabled using W=1
Signed-off-by: Dave Jones <davej@redhat.com> Acked-by: Sam Ravnborg <sam@ravnborg.org> Tested-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Michal Marek <mmarek@suse.cz> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Building a kernel with "make W=1" produces far too much noise to be
useful.
Divide the warning options in three groups:
W=1 - warnings that may be relevant and does not occur too often
W=2 - warnings that occur quite often but may still be relevant
W=3 - the more obscure warnings, can most likely be ignored
When building the whole kernel, those levels produce:
Many warnings occur from .h files so fixing one file may have a nice
effect on the total number of warnings.
With these changes I am actually tempted to try W=1 now and then.
Previously there was just too much noise.
Borislav:
- make the W= levels exclusive
- move very noisy and making little sense for the kernel warnings to W=3
- drop -Woverlength-strings due to useless warning message
- copy explanatory text for the different warning levels to 'make help'
- recount warnings per level
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Borislav Petkov <bp@alien8.de> Cc: Dave Jones <davej@redhat.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Michal Marek <mmarek@suse.cz>
[PG: used for 2.6.34 to better control new compilers on older code] Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Add a 'W=1' Makefile switch which adds additional checking per build
object.
The idea behind this option is targeted at developers who, in the
process of writing their code, want to do the occasional
make W=1 [target.o]
and let gcc do more extensive code checking for them. Then, they
could eyeball the output for valid gcc warnings about various
bugs/discrepancies which are not reported during the normal build
process.
For more background information and a use case, read through this
thread: http://marc.info/?l=kernel-janitors&m=129802065918147&w=2
Cc: Michal Marek <mmarek@suse.cz> Cc: linux-kbuild@vger.kernel.org Acked-by: Sam Ravnborg <sam@ravnborg.org> Acked-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Borislav Petkov <bp@alien8.de> Signed-off-by: Michal Marek <mmarek@suse.cz>
[PG: used for 2.6.34 to better control new compilers on older code] Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
In enter_state() we use "state" as an offset for the pm_states[]
array. The pm_states[] array only has PM_SUSPEND_MAX elements so
this test is off by one.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
On writes in MODE_RAW the mtd_oob_ops struct is not sufficiently
initialized which may cause nandwrite to fail. With this patch
it is possible to write raw nand/oob data without additional ECC
(either for testing or when some sectors need different oob layout
e.g. bootloader) like
nandwrite -n -r -o /dev/mtd0 <myfile>
Signed-off-by: Peter Wippich <pewi@gw-instruments.de> Tested-by: Ricard Wanderlof <ricardw@axis.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
L2TP for example uses NLA_MSECS like this:
policy:
[L2TP_ATTR_RECV_TIMEOUT] = { .type = NLA_MSECS, },
code:
if (info->attrs[L2TP_ATTR_RECV_TIMEOUT])
cfg.reorder_timeout = nla_get_msecs(info->attrs[L2TP_ATTR_RECV_TIMEOUT]);
As nla_get_msecs() is essentially nla_get_u64() plus the
conversion to a HZ-based value, this will not properly
reject attributes from userspace that aren't long enough
and might overrun the message.
Add NLA_MSECS to the attribute minlen array to check the
size properly.
Cc: Thomas Graf <tgraf@suug.ch> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The sunrpc layer keeps a cache of recently used credentials and
'unx_match' is used to find the credential which matches the current
process.
However unx_match allows a match when the cached credential has extra
groups at the end of uc_gids list which are not in the process group list.
So if a process with a list of (say) 4 group accesses a file and gains
access because of the last group in the list, then another process
with the same uid and gid, and a gid list being the first tree of the
gids of the original process tries to access the file, it will be
granted access even though it shouldn't as the wrong rpc credential
will be used.
Make sure that SCSI device removal via scsi_remove_host() does finish
all pending SCSI commands. Currently that's not the case and hence
removal of a SCSI host during I/O can cause a deadlock. See also
"blkdev_issue_discard() hangs forever if underlying storage device is
removed" (http://bugzilla.kernel.org/show_bug.cgi?id=40472). See also
http://lkml.org/lkml/2011/8/27/6.
Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The call to complete() in st_scsi_execute_end() wakes up sleeping thread
in write_behind_check(), which frees the st_request, thus invalidating
the pointer to the associated bio structure, which is then passed to the
blk_rq_unmap_user(). Fix by storing pointer to bio structure into
temporary local variable.
This bug is present since at least linux-2.6.32.
Signed-off-by: Petr Uzel <petr.uzel@suse.cz> Reported-by: Juergen Groß <juergen.gross@ts.fujitsu.com> Reviewed-by: Jan Kara <jack@suse.cz> Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The leap second rework unearthed another issue of inconsistent data.
On timekeeping_resume() the timekeeper data is updated, but nothing
calls timekeeping_update(), so now the update code in the timer
interrupt sees stale values.
This has been the case before those changes, but then the timer
interrupt was using stale data as well so this went unnoticed for quite
some time.
Add the missing update call, so all the data is consistent everywhere.
Reported-by: Andreas Schwab <schwab@linux-m68k.org> Reported-and-tested-by: "Rafael J. Wysocki" <rjw@sisk.pl> Reported-and-tested-by: Martin Steigerwald <Martin@lichtvoll.de> Cc: LKML <linux-kernel@vger.kernel.org> Cc: Linux PM list <linux-pm@vger.kernel.org> Cc: John Stultz <johnstul@us.ibm.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>, Cc: Prarit Bhargava <prarit@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: John Stultz <johnstul@us.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Linux Kernel <linux-kernel@vger.kernel.org> Signed-off-by: John Stultz <johnstul@us.ibm.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The update of the hrtimer base offsets on all cpus cannot be made
atomically from the timekeeper.lock held and interrupt disabled region
as smp function calls are not allowed there.
clock_was_set(), which enforces the update on all cpus, is called
either from preemptible process context in case of do_settimeofday()
or from the softirq context when the offset modification happened in
the timer interrupt itself due to a leap second.
In both cases there is a race window for an hrtimer interrupt between
dropping timekeeper lock, enabling interrupts and clock_was_set()
issuing the updates. Any interrupt which arrives in that window will
see the new time but operate on stale offsets.
So we need to make sure that an hrtimer interrupt always sees a
consistent state of time and offsets.
ktime_get_update_offsets() allows us to get the current monotonic time
and update the per cpu hrtimer base offsets from hrtimer_interrupt()
to capture a consistent state of monotonic time and the offsets. The
function replaces the existing ktime_get() calls in hrtimer_interrupt().
The overhead of the new function vs. ktime_get() is minimal as it just
adds two store operations.
This ensures that any changes to realtime or boottime offsets are
noticed and stored into the per-cpu hrtimer base structures, prior to
any hrtimer expiration and guarantees that timers are not expired early.
Signed-off-by: John Stultz <johnstul@us.ibm.com> Reviewed-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Acked-by: Prarit Bhargava <prarit@redhat.com> Link: http://lkml.kernel.org/r/1341960205-56738-8-git-send-email-johnstul@us.ibm.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Linux Kernel <linux-kernel@vger.kernel.org> Signed-off-by: John Stultz <johnstul@us.ibm.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
To finally fix the infamous leap second issue and other race windows
caused by functions which change the offsets between the various time
bases (CLOCK_MONOTONIC, CLOCK_REALTIME and CLOCK_BOOTTIME) we need a
function which atomically gets the current monotonic time and updates
the offsets of CLOCK_REALTIME and CLOCK_BOOTTIME with minimalistic
overhead. The previous patch which provides ktime_t offsets allows us
to make this function almost as cheap as ktime_get() which is going to
be replaced in hrtimer_interrupt().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Acked-by: Prarit Bhargava <prarit@redhat.com> Signed-off-by: John Stultz <johnstul@us.ibm.com> Link: http://lkml.kernel.org/r/1341960205-56738-7-git-send-email-johnstul@us.ibm.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Linux Kernel <linux-kernel@vger.kernel.org> Signed-off-by: John Stultz <johnstul@us.ibm.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
We need to update the base offsets from this code and we need to do
that under base->lock. Move the lock held region around the
ktime_get() calls. The ktime_get() calls are going to be replaced with
a function which gets the time and the offsets atomically.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Acked-by: Prarit Bhargava <prarit@redhat.com> Signed-off-by: John Stultz <johnstul@us.ibm.com> Link: http://lkml.kernel.org/r/1341960205-56738-6-git-send-email-johnstul@us.ibm.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Linux Kernel <linux-kernel@vger.kernel.org> Signed-off-by: John Stultz <johnstul@us.ibm.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
We need to update the hrtimer clock offsets from the hrtimer interrupt
context. To avoid conversions from timespec to ktime_t maintain a
ktime_t based representation of those offsets in the timekeeper. This
puts the conversion overhead into the code which updates the
underlying offsets and provides fast accessible values in the hrtimer
interrupt.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: John Stultz <johnstul@us.ibm.com> Reviewed-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Acked-by: Prarit Bhargava <prarit@redhat.com> Link: http://lkml.kernel.org/r/1341960205-56738-4-git-send-email-johnstul@us.ibm.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Linux Kernel <linux-kernel@vger.kernel.org> Signed-off-by: John Stultz <johnstul@us.ibm.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The timekeeping code misses an update of the hrtimer subsystem after a
leap second happened. Due to that timers based on CLOCK_REALTIME are
either expiring a second early or late depending on whether a leap
second has been inserted or deleted until an operation is initiated
which causes that update. Unless the update happens by some other
means this discrepancy between the timekeeping and the hrtimer data
stays forever and timers are expired either early or late.
The reported immediate workaround - $ data -s "`date`" - is causing a
call to clock_was_set() which updates the hrtimer data structures.
See: http://www.sheeri.com/content/mysql-and-leap-second-high-cpu-and-fix
Add the missing clock_was_set() call to update_wall_time() in case of
a leap second event. The actual update is deferred to softirq context
as the necessary smp function call cannot be invoked from hard
interrupt context.
Signed-off-by: John Stultz <johnstul@us.ibm.com> Reported-by: Jan Engelhardt <jengelh@inai.de> Reviewed-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Acked-by: Prarit Bhargava <prarit@redhat.com> Link: http://lkml.kernel.org/r/1341960205-56738-3-git-send-email-johnstul@us.ibm.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Linux Kernel <linux-kernel@vger.kernel.org> Signed-off-by: John Stultz <johnstul@us.ibm.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
clock_was_set() cannot be called from hard interrupt context because
it calls on_each_cpu().
For fixing the widely reported leap seconds issue it is necessary to
call it from hard interrupt context, i.e. the timer tick code, which
does the timekeeping updates.
Provide a new function which denotes it in the hrtimer cpu base
structure of the cpu on which it is called and raise the hrtimer
softirq. We then execute the clock_was_set() notificiation from
softirq context in run_hrtimer_softirq(). The hrtimer softirq is
rarely used, so polling the flag there is not a performance issue.
[ tglx: Made it depend on CONFIG_HIGH_RES_TIMERS. We really should get
rid of all this ifdeffery ASAP ]
Signed-off-by: John Stultz <johnstul@us.ibm.com> Reported-by: Jan Engelhardt <jengelh@inai.de> Reviewed-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Acked-by: Prarit Bhargava <prarit@redhat.com> Link: http://lkml.kernel.org/r/1341960205-56738-2-git-send-email-johnstul@us.ibm.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Linux Kernel <linux-kernel@vger.kernel.org> Signed-off-by: John Stultz <johnstul@us.ibm.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
While not a bugfix itself, it allows following fixes to backport
in a more straightforward manner.
CC: Thomas Gleixner <tglx@linutronix.de> CC: Eric Dumazet <eric.dumazet@gmail.com> CC: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Linux Kernel <linux-kernel@vger.kernel.org> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Commit 6b43ae8a61 (ntp: Fix leap-second hrtimer livelock) broke the
leapsecond update of CLOCK_MONOTONIC. The missing leapsecond update to
wall_to_monotonic causes discontinuities in CLOCK_MONOTONIC.
Adjust wall_to_monotonic when NTP inserted a leapsecond.
Reported-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: John Stultz <john.stultz@linaro.org> Tested-by: Richard Cochran <richardcochran@gmail.com> Link: http://lkml.kernel.org/r/1338400497-12420-1-git-send-email-john.stultz@linaro.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Linux Kernel <linux-kernel@vger.kernel.org> Signed-off-by: John Stultz <johnstul@us.ibm.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
In commit 6b43ae8a619d17c4935c3320d2ef9e92bdeed05d, I
introduced a bug that kept the STA_INS or STA_DEL bit
from being cleared from time_status via adjtimex()
without forcing STA_PLL first.
Usually once the STA_INS is set, it isn't cleared
until the leap second is applied, so its unlikely this
affected anyone. However during testing I noticed it
took some effort to cancel a leap second once STA_INS
was set.
Signed-off-by: John Stultz <johnstul@us.ibm.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Prarit Bhargava <prarit@redhat.com> Link: http://lkml.kernel.org/r/1342156917-25092-2-git-send-email-john.stultz@linaro.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When repeating a UTC time value during a leap second (when the UTC
time should be 23:59:60), the TAI timescale should not stop. The kernel
NTP code increments the TAI offset one second too late. This patch fixes
the issue by incrementing the offset during the leap second itself.
Signed-off-by: Richard Cochran <richardcochran@gmail.com> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Linux Kernel <linux-kernel@vger.kernel.org> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This should have been backported when it was commited, but I
mistook the problem as requiring the ntp_lock changes
that landed in 3.4 in order for it to occur.
Unfortunately the same issue can happen (with only one cpu)
as follows:
do_adjtimex()
write_seqlock_irq(&xtime_lock);
process_adjtimex_modes()
process_adj_status()
ntp_start_leap_timer()
hrtimer_start()
hrtimer_reprogram()
tick_program_event()
clockevents_program_event()
ktime_get()
seq = req_seqbegin(xtime_lock); [DEADLOCK]
This deadlock will no always occur, as it requires the
leap_timer to force a hrtimer_reprogram which only happens
if its set and there's no sooner timer to expire.
NOTE: This patch, being faithful to the original commit,
introduces a bug (we don't update wall_to_monotonic),
which will be resovled by backporting a following fix.
Original commit message below:
Since commit 7dffa3c673fbcf835cd7be80bb4aec8ad3f51168 the ntp
subsystem has used an hrtimer for triggering the leapsecond
adjustment. However, this can cause a potential livelock.
Thomas diagnosed this as the following pattern:
CPU 0 CPU 1
do_adjtimex()
spin_lock_irq(&ntp_lock);
process_adjtimex_modes(); timer_interrupt()
process_adj_status(); do_timer()
ntp_start_leap_timer(); write_lock(&xtime_lock);
hrtimer_start(); update_wall_time();
hrtimer_reprogram(); ntp_tick_length()
tick_program_event() spin_lock(&ntp_lock);
clockevents_program_event()
ktime_get()
seq = req_seqbegin(xtime_lock);
This patch tries to avoid the problem by reverting back to not using
an hrtimer to inject leapseconds, and instead we handle the leapsecond
processing in the second_overflow() function.
The downside to this change is that on systems that support highres
timers, the leap second processing will occur on a HZ tick boundary,
(ie: ~1-10ms, depending on HZ) after the leap second instead of
possibly sooner (~34us in my tests w/ x86_64 lapic).
This patch applies on top of tip/timers/core.
CC: Sasha Levin <levinsasha928@gmail.com> CC: Thomas Gleixner <tglx@linutronix.de> Reported-by: Sasha Levin <levinsasha928@gmail.com> Diagnoised-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Sasha Levin <levinsasha928@gmail.com> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Linux Kernel <linux-kernel@vger.kernel.org> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
In the ac.c, power_supply_register()'s return value is not checked.
As a result, the driver's add() ops may return success
even though the device failed to initialize.
For example, some BIOS may describe two ACADs in the same DSDT.
The second ACAD device will fail to register,
but ACPI driver's add() ops returns sucessfully.
The ACPI device will receive ACPI notification and cause OOPS.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This doesn't make much sense, and it exposes a bug in the kernel where
attempts to create a new file in an append-only directory using
O_CREAT will fail (but still leave a zero-length file). This was
discovered when xfstests #79 was generalized so it could run on all
file systems.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Modify Ethernet addess macros to be compatible with BE/LE platforms
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com> Cc: Chul Kim <chul.kim@idt.com> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Li Yang <leoli@freescale.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Commit a626ca6a6564 ("vm: fix vm_pgoff wrap in stack expansion") fixed
the case of an expanding mapping causing vm_pgoff wrapping when you had
downward stack expansion. But there was another case where IA64 and
PA-RISC expand mappings: upward expansion.
This fixes that case too.
Signed-off-by: Hugh Dickins <hughd@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[PG: .34 doesn't have perf call via 3af9e859 (in .36); adjust accordingly] Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Structures "l2cap_conninfo" and "rfcomm_conninfo" have one padding
byte each. This byte in "cinfo" is copied to userspace uninitialized.
Signed-off-by: Filip Palian <filip.palian@pjwstk.edu.pl> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
[PG: l2cap_sock.c chunk is in l2cap.c in a 2.6.34 context/baseline] Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
If the NLM daemon is killed on the NFS server, we can currently end up
hanging forever on an 'unlock' request, instead of aborting. Basically,
if the rpcbind request fails, or the server keeps returning garbage, we
really want to quit instead of retrying.
Tested-by: Vasily Averin <vvs@sw.ru> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
[PG: struct rpc_task in sched.h slightly different layout vs. v3.0] Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
All of those are rw-r--r-- and all are broken for suid - if you open
a file before the target does suid-root exec, you'll be still able
to access it. For personality it's not a big deal, but for syscall
and stack it's a real problem.
Fix: check that task is tracable for you at the time of read().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[PG: in .34 cred_guard_mutex is in task, not task->signal] Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Lower SCM_MAX_FD from 255 to 253 so that allocations for scm_fp_list are
halved. (commit f8d570a4 added two pointers in this structure)
scm_fp_dup() should not copy whole structure (and trigger kmemcheck
warnings), but only the used part. While we are at it, only allocate
needed size.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The newer Lenovo ThinkPads have HKEY HID of LEN0068 instead
of IBM0068. Added new HID so that thinkpad_acpi module will
auto load on these newer Lenovo ThinkPads.
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com> Signed-off-by: Andy Lutomirski <luto@mit.edu> Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The patches missed an indirect use of IRQF_NO_SUSPEND pulled in via
IRQF_TIMER. The following patch fixes the issue.
With this fixlet PV guest migration works just fine. I also booted the
entire series as a dom0 kernel and it appeared fine.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
ubd_file_size() cannot use ubd_dev->cow.file because at this time
ubd_dev->cow.file is not initialized.
Therefore, ubd_file_size() will always report a wrong disk size when
COW files are used.
Reading from /dev/ubd* would crash the kernel.
We have to read the correct disk size from the COW file's backing
file.
Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
To configure pads during the initialisation a set of special constants
is used, e.g.
#define MX25_PAD_FEC_MDIO__FEC_MDIO IOMUX_PAD(0x3c4, 0x1cc, 0x10, 0, 0, PAD_CTL_HYS | PAD_CTL_PUS_22K_UP)
The problem is that no pull-up/down is getting activated unless both
PAD_CTL_PUE (pull-up enable) and PAD_CTL_PKE (pull/keeper module
enable) set. This is clearly stated in the i.MX25 datasheet and is
confirmed by the measurements on hardware. This leads to some rather
hard to understand bugs such as misdetecting an absent ethernet PHY (a
real bug i had), unstable data transfer etc. This might affect mx25,
mx35, mx50, mx51 and mx53 SoCs.
It's reasonable to expect that if the pullup value is specified, the
intention was to have it actually active, so we implicitly add the
needed bits.
Signed-off-by: Paul Fertser <fercerpav@gmail.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This device is not using the proper demod IF. Instead of using the
IF macro, it is specifying a IF frequency. This doesn't work, as xc3028
needs to load an specific SCODE for the tuner. In this case, there's
no IF table for 5 MHz.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
If the bus has been reset on resume, set the alternate setting to 0.
This should be the default value, but some devices crash or otherwise
misbehave if they don't receive a SET_INTERFACE request before any other
video control request.
Microdia's 0c45:6437 camera has been found to require this change or it
will stop sending video data after resume.
uvc_video.c]
Signed-off-by: Ming Lei <ming.lei@canonical.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de> Cc: Paul Mundt <lethal@linux-sh.org> Cc: Sebastian Siewior <bigeasy@linutronix.de> Signed-off-by: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The shift direction was wrong because the function takes a
page number and i is the address is the loop.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
[PG: drivers/iommu/ was arch/x86/kernel/ in 2.6.34 context] Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Put sysfs attributes of ccwgroup devices in an attribute group to
ensure that these attributes are actually present when userspace
is notified via uevents.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
ak4535_reg should be 8bit, but cache table is defined as 16bit.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
ak4642 register was 8bit, but cache table was defined as 16bit.
ak4642 doesn't work correctry without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reported-by: Chris Paulson-Ellis <chris@edesix.com> Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
[PG: in .34 it uses codec->bias_level and not codec->dapm.bias_level] Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Fan Yong <yong.fan@whamcloud.com> noticed setting
FMODE_32bithash wouldn't work with nfsd v4, as
nfsd4_readdir() checks for 32 bit cookies. However, according to RFC 3530
cookies have a 64 bit type and cookies are also defined as u64 in
'struct nfsd4_readdir'. So remove the test for >32-bit values.
Signed-off-by: Bernd Schubert <bernd.schubert@itwm.fraunhofer.de> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The parameter's origin type is long. On an i386 architecture, it can
easily be larger than 0x80000000, causing this function to convert it
to a sign-extended u64 type.
Change the type to unsigned long so we get the correct result.
Signed-off-by: hank <pyu@redhat.com> Cc: John Stultz <john.stultz@linaro.org>
[ build fix ] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Due to post-increment in condition of kmod_loop_msg in __request_module(),
the system log can be spammed by much more than 5 instances of the 'runaway
loop' message if the number of events triggering it makes the kmod_loop_msg
to overflow.
Fix that by making sure we never increment it past the threshold.
Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The stable@kernel.org email address has been replaced with the
stable@vger.kernel.org mailing list. Change the stable kernel rules to
reference the new list instead of the semi-defunct email alias.
Some Stellaris evaluation kits have the JTAG/SWD FTDI chip onboard,
and some, like EK-LM3S9B90, come with a separate In-Circuit Debugger
Interface Board. The ICDI board can also be used stand-alone, for
other boards and chips than the kit it came with. The ICDI has both
old style 20-pin JTAG connector and new style JTAG/SWD 10-pin 1.27mm
pitch connector.
Tested with EK-LM3S9B90, where the BD-ICDI board is included.
Signed-off-by: Peter Stuge <peter@stuge.se> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Add vendor and product ID for the SMART USB to serial adapter. These
were meant to be used with their SMART Board whiteboards, but can be
re-purposed for other tasks. Tested and working (at at least 9600 bps).
Signed-off-by: Eric Benoit <eric@ecks.ca> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The new runtime PM code has shown that many webcams suffer
from a race condition that may crash them upon resume.
Runtime PM is especially prone to show the problem because
it retains power to the cameras at all times. However
system suspension may also crash the devices and retain
power to the devices.
The only way to solve this problem without races is in
usbcore with the RESET_RESUME quirk.
Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Alan Stern points out that after spin_unlock(&ps->lock) there is no
guarantee that ps->pid won't be freed. Since kill_pid_info_as_uid() is
called after the spin_unlock(), the pid passed to it must be pinned.
Reported-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Serge Hallyn <serge.hallyn@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This patch solves two things:
1) Enables autosense emulation code to correctly
interpret descriptor format sense data, and
2) Fixes a bug whereby the autosense emulation
code would overwrite descriptor format sense data
with SENSE KEY HARDWARE ERROR in fixed format, to
incorrectly look like this:
Oct 21 14:11:07 localhost kernel: sd 7:0:0:0: [sdc] Sense Key : Recovered Error [current] [descriptor]
Oct 21 14:11:07 localhost kernel: Descriptor sense data with sense descriptors (in hex):
Oct 21 14:11:07 localhost kernel: 72 01 04 1d 00 00 00 0e 09 0c 00 00 00 00 00 00
Oct 21 14:11:07 localhost kernel: 00 4f 00 c2 00 50
Oct 21 14:11:07 localhost kernel: sd 7:0:0:0: [sdc] ASC=0x4 ASCQ=0x1d
Signed-off-by: Luben Tuikov <ltuikov@yahoo.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
epoll can acquire recursively acquire ep->mtx on multiple "struct
eventpoll"s at once in the case where one epoll fd is monitoring another
epoll fd. This is perfectly OK, since we're careful about the lock
ordering, but it causes spurious lockdep warnings. Annotate the recursion
using mutex_lock_nested, and add a comment explaining the nesting rules
for good measure.
Recent versions of systemd are triggering this, and it can also be
demonstrated with the following trivial test program:
--------------------8<--------------------
int main(void) {
int e1, e2;
struct epoll_event evt = {
.events = EPOLLIN
};
Reported-by: Paul Bolle <pebolle@tiscali.nl> Tested-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Nelson Elhage <nelhage@nelhage.com> Acked-by: Jason Baron <jbaron@redhat.com> Cc: Dave Jones <davej@redhat.com> Cc: Davide Libenzi <davidel@xmailserver.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
When compiling an i386_defconfig kernel with gcc-4.6.1-9.fc15.i686, I
noticed a warning about the asm operand for test_bit in kprobes'
can_boost. I discovered that this caused only the first long of
twobyte_is_boostable[] to be output.
Jakub filed and fixed gcc PR50571 to correct the warning and this output
issue. But to solve it for less current gcc, we can make kprobes'
twobyte_is_boostable[] non-const, and it won't be optimized out.
Before:
CC arch/x86/kernel/kprobes.o
In file included from include/linux/bitops.h:22:0,
from include/linux/kernel.h:17,
from [...]/arch/x86/include/asm/percpu.h:44,
from [...]/arch/x86/include/asm/current.h:5,
from [...]/arch/x86/include/asm/processor.h:15,
from [...]/arch/x86/include/asm/atomic.h:6,
from include/linux/atomic.h:4,
from include/linux/mutex.h:18,
from include/linux/notifier.h:13,
from include/linux/kprobes.h:34,
from arch/x86/kernel/kprobes.c:43:
[...]/arch/x86/include/asm/bitops.h: In function ‘can_boost.part.1’:
[...]/arch/x86/include/asm/bitops.h:319:2: warning: use of memory input
without lvalue in asm operand 1 is deprecated [enabled by default]
Libsas forget to set the sas_address and device type of rphy lead to file
under /sys/class/sas_x show wrong value, fix that.
Signed-off-by: Jack Wang <jack_wang@usish.com> Tested-by: Crystal Yu <crystal_yu@usish.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
During kdump testing I noticed timeouts when initialising each IPR
adapter. While the driver has logic to detect an adapter in an
indeterminate state, it wasn't triggering and each adapter went
through a 5 minute timeout before finally going operational.
Some analysis showed the needs_hard_reset flag wasn't getting set.
We can check the reset_devices kernel parameter which is set by
kdump and force a full reset. This fixes the problem.
Signed-off-by: Anton Blanchard <anton@samba.org> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
There are 2 situations wherein the xhci_ring* might not get freed:
- When xhci_ring_alloc() -> xhci_segment_alloc() returns NULL and
we goto the fail: label in xhci_ring_alloc. In this case, the ring
will not get kfreed.
- When the num_segs argument to xhci_ring_alloc is passed as 0 and
we try to free the rung after that.
( This doesn't really happen as of now in the code but we seem to
be entertaining num_segs=0 in xhci_ring_alloc )
This should be backported to kernels as old as 2.6.31.
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
If the usermode app does an ioctl over this serial device by
using TIOCMIWAIT, then the code will wait by setting the current
task state to TASK_INTERRUPTIBLE and then calling schedule().
This will be woken up by the qt2_process_modem_status on URB
completion when the port_extra->shadowMSR is set to the new
modem status.
However, this could result in a lost wakeup scenario due to a race
in the logic in the qt2_ioctl(TIOCMIWAIT) loop and the URB completion
for new modem status in qt2_process_modem_status.
Due to this, the usermode app's task will continue to sleep despite a
change in the modem status.
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
x25_find_listener does not check that the amount of call user data given
in the skb is big enough in per-socket comparisons, hence buffer
overreads may occur. Fix this by adding a check.
Signed-off-by: Matthew Daley <mattjd@gmail.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Andrew Hendry <andrew.hendry@gmail.com> Acked-by: Andrew Hendry <andrew.hendry@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The w83627ehf driver is improperly reporting thermal diode sensors as
type 2, instead of 3. This caused "sensors" and possibly other
monitoring tools to report these sensors as "transistor" instead of
"thermal diode".
Furthermore, diode subtype selection (CPU vs. external) is only
supported by the original W83627EHF/EHG. All later models only support
CPU diode type, and some (NCT6776F) don't even have the register in
question so we should avoid reading from it.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Patch to add SiGma Micro-based keyboards (1c4f:0002) to hid-quirks.
These keyboards dont seem to allow the records to be initialized, and hence a
timeout occurs when the usbhid driver attempts to initialize them. The patch
just adds the signature for these keyboards to the hid-quirks list with the
setting HID_QUIRK_NO_INIT_REPORTS. This removes the 5-10 second wait for the
timeout to occur.
Like e65cc194f7628ecaa02462f22f42fb09b50dcd49 this patch enables 64bit DMA
for the AHCI SATA controller of a board that has the SB600 southbridge. In
this case though we're enabling 64bit DMA for the Asus M3A motherboard. It
is a new enough board that all of the BIOS releases since the initial
release (0301 from 2007-10-22) work correctly with 64bit DMA enabled.
Signed-off-by: Mark Nelson <mdnelson8@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@pobox.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The following patch is admittedly a band-aid, and does not solve the
root cause, but it still is a good candidate for hardening as a pointer
check before reference.
Signed-off-by: Mark Salyzyn <mark_salyzyn@us.xyratex.com> Tested-by: Jack Wang <jack_wang@usish.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Incorrect variable was used in validating the akm_suites array from
NL80211_ATTR_AKM_SUITES. In addition, there was no explicit
validation of the array length (we only have room for
NL80211_MAX_NR_AKM_SUITES).
This can result in a buffer write overflow for stack variables with
arbitrary data from user space. The nl80211 commands using the affected
functionality require GENL_ADMIN_PERM, so this is only exposed to admin
users.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
In an enclosure model where there are chaining expanders to a large body
of storage, it was discovered that libsas, responding to a broadcast
event change, would only revalidate the domain of first child expander
in the list.
The issue is that the pointer value to the discovered source device was
used to break out of the loop, rather than the content of the pointer.
This still remains non-compliant as the revalidate domain code is
supposed to loop through all child expanders, and not stop at the first
one it finds that reports a change count. However, the design of this
routine does not allow multiple device discoveries and that would be a
more complicated set of patches reserved for another day. We are fixing
the glaring bug rather than refactoring the code.
Signed-off-by: Mark Salyzyn <msalyzyn@us.xyratex.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Following reports on the list, it looks like the 3e-9xxx driver will leak dma
mappings every time we get a transient queueing error back from the card.
This is because it maps the sg list in the routine that sends the command, but
doesn't unmap again in the transient failure path (even though the command is
sent back to the block layer). Fix by unmapping before returning the status.
Reported-by: Chris Boot <bootc@bootc.net> Tested-by: Chris Boot <bootc@bootc.net> Acked-by: Adam Radford <aradford@gmail.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
When the headphone pin is assigned as primary output to line_out_pins[],
the automatic HP-pin assignment by ASSID must be suppressed. Otherwise
a wrong pin might be assigned to the headphone and breaks the auto-mute.
During NETDEV_UP, we use symbol_get() to get the net driver's cnic
probe function. This sometimes doesn't work if NETDEV_UP happens
right after NETDEV_REGISTER and the net driver is still running module
init code. As a result, the cnic device may not be discovered. We
fix this by probing on all NETDEV events if the device's netif_running
state is up.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Have libiscsi_tcp have upper layers allocate the LLD data
along with the iscsi_cls_conn struct, so it is refcounted.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Commit 3321c07ae5068568cd61ac9f4ba749006a7185c9 correctly clears the TPM
buffer if the user specified read length is >= the TPM buffer length. However,
if the user specified read length is < the TPM buffer length, then part of the
TPM buffer is left uncleared.
This patch changes the call of tpm_transmit by supplying the size of the
userspace buffer instead of TPM_BUFSIZE.
This got assigned CVE-2011-1161.
[The first hunk didn't make sense given one could expect
way less data than TPM_BUFSIZE, so added tpm_transmit boundary
check over bufsiz instead
The last parameter of tpm_transmit() reflects the amount
of data expected from the device, and not the buffer size
being supplied to it. It isn't ideal to parse it directly,
so we just set it to the maximum the input buffer can handle
and let the userspace API to do such job.]
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com> Signed-off-by: James Morris <jmorris@namei.org> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Currently, the hvc_console_print() function drops console output if the
hvc backend's put_chars() returns 0. This patch changes this behavior
to allow a retry through returning -EAGAIN.
This change also affects the hvc_push() function. Both functions are
changed to handle -EAGAIN and to retry the put_chars() operation.
If a hvc backend returns -EAGAIN, the retry handling differs:
- hvc_console_print() spins to write the complete console output.
- hvc_push() behaves the same way as for returning 0.
Now hvc backends can indirectly control the way how console output is
handled through the hvc console layer.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Acked-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[PG: map drivers/tty/hvc/ --> drivers/char for v2.6.34 baseline]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This device can be found in Acer Iconia TAB W500 tablet dock.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
During the association, the regulatory is updated by country IE
that reaps the previously found beacons. The impact is that
after a STA disconnects *or* when for any reason a regulatory
domain change happens the beacon hint flag is not cleared
therefore preventing future beacon hints to be learned.
This is important as a regulatory domain change or a restore
of regulatory settings would set back the passive scan and no-ibss
flags on the channel. This is the right place to do this given that
it covers any regulatory domain change.
Reviewed-by: Luis R. Rodriguez <mcgrof@gmail.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
In ad-hoc mode, driver b43 does not issue beacons.
Signed-off-by: Manual Munz <freifunk@somakoma.de> Tested-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This patch fixes "Surround Speaker Playback Volume" being cut off.
(Commit b4dabfc452a10 was probably meant to fix this, but it fixed
only the "Switch" name, not the "Volume" name.)
Signed-off-by: David Henningsson <david.henningsson@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
We need to report the entire jack state to the core jack code, not just
the bits that were being updated by the caller, otherwise the status
reported by other detection methods will be omitted from the state seen
by userspace.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The checksum field in the EEPROM on HPPA is really not a
checksum but a signature (0x16d6). So allow 0x16d6 as the
matching checksum on HPPA systems.
This issue is present on longterm/stable kernels, I have
verified that this patch is applicable back to at least
2.6.32.y kernels.
v2- changed ifdef to use CONFIG_PARISC instead of __hppa__
CC: Guy Martin <gmsoft@tuxicoman.be> CC: Rolf Eike Beer <eike-kernel@sf-tec.de> CC: Matt Turner <mattst88@gmail.com> Reported-by: Mikulas Patocka <mikulas@artax.kerlin.mff.cuni.cz> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Transitioning to a LOOP_UPDATE loop-state could cause the driver
to miss normal link/target processing. LOOP_UPDATE is a crufty
artifact leftover from at time the driver performed it's own
internal command-queuing. Safely remove this state.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
WARNING: drivers/net/irda/smsc-ircc2.o(.devinit.text+0x1a7): Section mismatch in reference from the function smsc_ircc_pnp_probe() to the function .init.text:smsc_ircc_open()
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
There was a BUG_ON to protect against a bad id which could be dealt with
more gracefully.
Reported-by: Natalie Orlin <norlin@us.ibm.com> Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
DA850/OMAP-L138 EMAC driver uses random mac address instead of
a fixed one because the mac address is not stuffed into EMAC
platform data.
This patch provides a function which reads the mac address
stored in SPI flash (registered as MTD device) and populates the
EMAC platform data. The function which reads the mac address is
registered as a callback which gets called upon addition of MTD
device.
NOTE: In case the MAC address stored in SPI flash is erased, follow
the instructions at [1] to restore it.
Modifications in v2:
Guarded registering the mtd_notifier only when MTD is enabled.
Earlier this was handled using mtd_has_partitions() call, but
this has been removed in Linux v3.0.
Modifications in v3:
a. Guarded da850_evm_m25p80_notify_add() function and
da850evm_spi_notifier structure with CONFIG_MTD macros.
b. Renamed da850_evm_register_mtd_user() function to
da850_evm_setup_mac_addr() and removed the struct mtd_notifier
argument to this function.
c. Passed the da850evm_spi_notifier structure to register_mtd_user()
function.
Modifications in v4:
Moved the da850_evm_setup_mac_addr() function within the first
CONFIG_MTD ifdef construct.
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
projects / karo-tx-linux.git / log