* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: fix parsing of hostname in dfs referrals
cifs: display fsc in /proc/mounts
cifs: enable fscache iff fsc mount option is used explicitly
cifs: allow fsc mount option only if CONFIG_CIFS_FSCACHE is set
cifs: Handle extended attribute name cifs_acl to generate cifs acl blob (try #4)
cifs: Misc. cleanup in cifsacl handling [try #4]
cifs: trivial comment fix for cifs_invalidate_mapping
[CIFS] fs/cifs/Kconfig: CIFS depends on CRYPTO_HMAC
cifs: don't take extra tlink reference in initiate_cifs_search
cifs: Percolate error up to the caller during get/set acls [try #4]
cifs: fix another memleak, in cifs_root_iget
cifs: fix potential use-after-free in cifs_oplock_break_put
xen: fix MSI setup and teardown for PV on HVM guests
When remapping MSIs into pirqs for PV on HVM guests, qemu is responsible
for doing the actual mapping and unmapping.
We only give qemu the desired pirq number when we ask to do the mapping
the first time, after that we should be reading back the pirq number
from qemu every time we want to re-enable the MSI.
This fixes a bug in xen_hvm_setup_msi_irqs that manifests itself when
trying to enable the same MSI for the second time: the old MSI to pirq
mapping is still valid at this point but xen_hvm_setup_msi_irqs would
try to assign a new pirq anyway.
A simple way to reproduce this bug is to assign an MSI capable network
card to a PV on HVM guest, if the user brings down the corresponding
ethernet interface and up again, Linux would fail to enable MSIs on the
device.
xen: use PHYSDEVOP_get_free_pirq to implement find_unbound_pirq
Use the new hypercall PHYSDEVOP_get_free_pirq to ask Xen to allocate a
pirq. Remove the unsupported PHYSDEVOP_get_nr_pirqs hypercall to get the
amount of pirq available.
This fixes find_unbound_pirq that otherwise would return a number
starting from nr_irqs that might very well be out of range in Xen.
The symptom of this bug is that when you passthrough an MSI capable pci
device to a PV on HVM guest, Linux would fail to enable MSIs on the
device.
Wim Van Sebroeck [Sat, 23 Oct 2010 20:59:42 +0000 (20:59 +0000)]
watchdog: bcm63xx_wdt: improve platform part.
* fix devinit and devexit sections
* fix platform removal code so that the iounmap happens after the removal of the timer.
* changes the reboot_notifier by a platform shutdown method.
Jarkko Nikula [Wed, 1 Dec 2010 09:01:20 +0000 (11:01 +0200)]
ASoC: omap: N810: Don't select CONFIG_OMAP_MUX but make it as dependency
Not all omap boards use kernel based pin multiplexing so
CONFIG_SND_OMAP_SOC_N810 should not select it by default as it can make
harm to other boards in multi-board kernels.
Therefore put CONFIG_OMAP_MUX as a dependency to N810 ASoC machine driver.
Thanks to Tony Lindgren <tony@atomide.com> for noticing.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Cc: Tony Lindgren <tony@atomide.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Daniel T Chen [Thu, 2 Dec 2010 00:16:07 +0000 (19:16 -0500)]
ALSA: hda: Use "alienware" model quirk for another SSID
BugLink: https://launchpad.net/bugs/683695
The original reporter states that headphone jacks do not appear to
work. Upon inspecting his codec dump, and upon further testing, it is
confirmed that the "alienware" model quirk is correct.
Reported-and-tested-by: Cody Thierauf Cc: <stable@kernel.org> [2.6.32+] Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Vasiliy Kulikov [Sun, 14 Nov 2010 09:22:52 +0000 (09:22 +0000)]
IB: Fix information leak in marshalling code
ib_ucm_init_qp_attr() and ucma_init_qp_attr() pass struct ib_uverbs_qp_attr
with reserved, qp_state, {ah_attr,alt_ah_attr}{reserved,->grh.reserved}
fields uninitialized to copy_to_user(). This leads to leaking of
contents of kernel stack memory to userspace.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Eli Cohen [Mon, 15 Nov 2010 14:04:39 +0000 (14:04 +0000)]
IB/mlx4: Fix IBoE reported link rate
The link rate is the product of the link speed in the link width. For
Etherent ports the rate is 10G, so we use 1 for the width and 4 for
speed to get the correct rate.
Signed-off-by: Eli Cohen <eli@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Eli Cohen [Wed, 10 Nov 2010 12:52:37 +0000 (12:52 +0000)]
mlx4_core: Workaround firmware bug in query dev cap
ConnectX firmware is supposed to report the number blue flame
registers per page as log2 of the value. However, due to a firmware
bug, it reports actual number. This patch works around this by
checking if the number of registers calculated fits within a page. If
it does not, we use 8 registers per page.
Signed-off-by: Eli Cohen <eli@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Yehuda Sadeh [Fri, 19 Nov 2010 22:51:04 +0000 (14:51 -0800)]
rbd: replace the rbd sysfs interface
The new interface creates directories per mapped image
and under each it creates a subdir per available snapshot.
This allows keeping a cleaner interface within the sysfs
guidelines. The ABI documentation was updated too.
Chien Tung [Tue, 2 Nov 2010 16:29:54 +0000 (16:29 +0000)]
MAINTAINERS: Update NetEffect entry
Correct web link as www.neteffect.com is no longer valid. Remove
Chien Tung as maintainer. I am moving on to other responsibilities at
Intel. Thanks for all the fish.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Dave Chinner [Tue, 30 Nov 2010 04:15:31 +0000 (15:15 +1100)]
xfs: only run xfs_error_test if error injection is active
Recent tests writing lots of small files showed the flusher thread
being CPU bound and taking a long time to do allocations on a debug
kernel. perf showed this as the prime reason:
samples pcnt function DSO
_______ _____ ___________________________ _________________
Walking btree blocks during allocation checking them requires each
block (a cache hit, so no I/O) call xfs_error_test(), which then
does a random32() call as the first operation. IOWs, ~50% of the
CPU is being consumed just testing whether we need to inject an
error, even though error injection is not active.
Kill this overhead when error injection is not active by adding a
global counter of active error traps and only calling into
xfs_error_test when fault injection is active.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de>
Dave Chinner [Tue, 30 Nov 2010 04:15:46 +0000 (15:15 +1100)]
xfs: avoid moving stale inodes in the AIL
When an inode has been marked stale because the cluster is being
freed, we don't want to (re-)insert this inode into the AIL. There
is a race condition where the cluster buffer may be unpinned before
the inode is inserted into the AIL during transaction committed
processing. If the buffer is unpinned before the inode item has been
committed and inserted, then it is possible for the buffer to be
released and hence processthe stale inode callbacks before the inode
is inserted into the AIL.
In this case, we then insert a clean, stale inode into the AIL which
will never get removed by an IO completion. It will, however, get
reclaimed and that triggers an assert in xfs_inode_free()
complaining about freeing an inode still in the AIL.
This race can be avoided by not moving stale inodes forward in the AIL
during transaction commit completion processing. This closes the
race condition by ensuring we never insert clean stale inodes into
the AIL. It is safe to do this because a dirty stale inode, by
definition, must already be in the AIL.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de>
Dave Chinner [Tue, 30 Nov 2010 04:16:02 +0000 (15:16 +1100)]
xfs: delayed alloc blocks beyond EOF are valid after writeback
There is an assumption in the parts of XFS that flushing a dirty
file will make all the delayed allocation blocks disappear from an
inode. That is, that after calling xfs_flush_pages() then
ip->i_delayed_blks will be zero.
This is an invalid assumption as we may have specualtive
preallocation beyond EOF and they are recorded in
ip->i_delayed_blks. A flush of the dirty pages of an inode will not
change the state of these blocks beyond EOF, so a non-zero
deeelalloc block count after a flush is valid.
The bmap code has an invalid ASSERT() that needs to be removed, and
the swapext code has a bug in that while it swaps the data forks
around, it fails to swap the i_delayed_blks counter associated with
the fork and hence can get the block accounting wrong.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de>
Dave Chinner [Tue, 30 Nov 2010 04:16:16 +0000 (15:16 +1100)]
xfs: push stale, pinned buffers on trylock failures
As reported by Nick Piggin, XFS is suffering from long pauses under
highly concurrent workloads when hosted on ramdisks. The problem is
that an inode buffer is stuck in the pinned state in memory and as a
result either the inode buffer or one of the inodes within the
buffer is stopping the tail of the log from being moved forward.
The system remains in this state until a periodic log force issued
by xfssyncd causes the buffer to be unpinned. The main problem is
that these are stale buffers, and are hence held locked until the
transaction/checkpoint that marked them state has been committed to
disk. When the filesystem gets into this state, only the xfssyncd
can cause the async transactions to be committed to disk and hence
unpin the inode buffer.
This problem was encountered when scaling the busy extent list, but
only the blocking lock interface was fixed to solve the problem.
Extend the same fix to the buffer trylock operations - if we fail to
lock a pinned, stale buffer, then force the log immediately so that
when the next attempt to lock it comes around, it will have been
unpinned.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de>
Dave Chinner [Tue, 30 Nov 2010 04:14:39 +0000 (15:14 +1100)]
xfs: fix failed write truncation handling.
Since the move to the new truncate sequence we call xfs_setattr to
truncate down excessively instanciated blocks. As shown by the testcase
in kernel.org BZ #22452 that doesn't work too well. Due to the confusion
of the internal inode size, and the VFS inode i_size it zeroes data that
it shouldn't.
But full blown truncate seems like overkill here. We only instanciate
delayed allocations in the write path, and given that we never released
the iolock we can't have converted them to real allocations yet either.
The only nasty case is pre-existing preallocation which we need to skip.
We already do this for page discard during writeback, so make the delayed
allocation block punching a generic function and call it from the failed
write path as well as xfs_aops_discard_page. The callers are
responsible for ensuring that partial blocks are not truncated away,
and that they hold the ilock.
Based on a fix originally from Christoph Hellwig. This version used
filesystem blocks as the range unit.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de>
initramfs: Really fix build break on symbol-prefixed archs
Define the __initramfs_size variable using VMLINUX_SYMBOL() to take care
of symbol-prefixed architectures, for example, blackfin.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Cc: Mike Frysinger <vapier.adi@gmail.com> Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>, Cc: Michal Marek <mmarek@suse.cz> Cc: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[mmarek: leave out Makefile change, since d63f6d1 already takes care of the
SYMBOL_PREFIX define] Signed-off-by: Michal Marek <mmarek@suse.cz>
Daniel Drake [Tue, 30 Nov 2010 20:34:52 +0000 (20:34 +0000)]
lxfb: Maintain video processor palette through suspend/resume
The Geode X driver uses both of the LX's palettes, one for gamma
correction and one for colormaps.
The kernel driver currently only backs up the one used for colormaps
during suspend/resume. If you mess with gamma settings and do a
suspend/resume, colors go funny.
Fix this by backing up the video proc palette during suspend/resume,
alongside the display controller one which is already handled.
Signed-off-by: Daniel Drake <dsd@laptop.org> Acked-by: Andres Salomon <dilinger@queued.net> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Bug is, if interrupt handler is called before initialization is
finished, raster controller is enabled and following register
modifications causes hardware to stay in a broken state.
By looking at this one may say that proper locking is missing in
this driver, and a more proper fix should be prepared. However,
aformentioned commit causes a regression in the driver and some
fix to current one should be applied first.
Signed-off-by: Caglar Akyuz <caglar@bilkon-kontrol.com.tr> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There are places in Linux where writes to newly allocated page
cache pages happen without a subsequent call to flush_dcache_page()
(several PIO drivers including USB HCD). This patch changes the
meaning of PG_arch_1 to be PG_dcache_clean and always flush the
D-cache for a newly mapped page in update_mmu_cache().
This addresses issues seen with executing binaries from MMC, in
addition to some of the other HCDs that don't explicitly do cache
management for their pipe-in buffers.
Requested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Linus Torvalds [Wed, 1 Dec 2010 04:13:35 +0000 (20:13 -0800)]
Merge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: add workaround for dce3 ddc line vbios bug
drm/radeon/kms: fix interlaced and doublescan handling
drm/radeon/kms: fix typos in disabled vbios code
Revert "drm/i915/dp: use VBT provided eDP params if available"
drm/i915: Clear pfit registers when not used by any outputs
drm: record monitor status in output_poll_execute
drm: Set connector DPMS status to ON in drm_crtc_helper_set_config
drm/i915: fix regression due to ba3d8d749b01548b9
Revert "drm/radeon/kms: fix typo in r600 cs checker"
drm/i915/sdvo: Always add a 30ms delay to make SDVO TV detection reliable
MAINTAINERS: INTEL DRM DRIVERS list (intel-gfx) is subscribers-only
drm/i915/sdvo: Always fallback to querying the shared DDC line
drm/i915: Handle pagefaults in execbuffer user relocations
drm/i915/sdvo: Only enable HDMI encodings only if the commandset is supported
drm/radeon/kms: fix resume regression for some r5xx laptops
drm/radeon/kms: fix regression in rs4xx i2c setup
drm/i915: Only save/restore cursor regs if !KMS
drm/i915: Prevent integer overflow when validating the execbuffer
Dave Airlie [Wed, 1 Dec 2010 02:10:34 +0000 (12:10 +1000)]
Merge remote branch 'intel/drm-intel-fixes' of /ssd/git/drm-next into drm-fixes
* 'intel/drm-intel-fixes' of /ssd/git/drm-next:
Revert "drm/i915/dp: use VBT provided eDP params if available"
drm/i915: Clear pfit registers when not used by any outputs
drm/i915: fix regression due to ba3d8d749b01548b9
Linus Torvalds [Wed, 1 Dec 2010 01:57:57 +0000 (17:57 -0800)]
Merge branch 'for_linus' of git://github.com/at91linux/linux-2.6-at91
* 'for_linus' of git://github.com/at91linux/linux-2.6-at91:
at91/board-yl-9200: fix typo in video support
atmel_spi: fix warning In function 'atmel_spi_dma_map_xfer'
at91/picotux200: remove commenting usb device and dataflash support
at91: rename rm9200ek and rm9200dk board file name
at91rm9200ek: fix warning: 'ek_mmc_data' defined but not used
at91rm9200dk: fix warning: 'dk_mmc_data' defined but not used
at91: Convert remaining boards to new-style UART initialization
at91: merge all at91rm9200 defconfig in one single file
Oleg Nesterov [Tue, 30 Nov 2010 19:56:02 +0000 (20:56 +0100)]
exec: copy-and-paste the fixes into compat_do_execve() paths
Note: this patch targets 2.6.37 and tries to be as simple as possible.
That is why it adds more copy-and-paste horror into fs/compat.c and
uglifies fs/exec.c, this will be cleanuped later.
compat_copy_strings() plays with bprm->vma/mm directly and thus has
two problems: it lacks the RLIMIT_STACK check and argv/envp memory
is not visible to oom killer.
Export acct_arg_size() and get_arg_page(), change compat_copy_strings()
to use get_arg_page(), change compat_do_execve() to do acct_arg_size(0)
as do_execve() does.
Add the fatal_signal_pending/cond_resched checks into compat_count() and
compat_copy_strings(), this matches the code in fs/exec.c and certainly
makes sense.
Oleg Nesterov [Tue, 30 Nov 2010 19:55:34 +0000 (20:55 +0100)]
exec: make argv/envp memory visible to oom-killer
Brad Spengler published a local memory-allocation DoS that
evades the OOM-killer (though not the virtual memory RLIMIT):
http://www.grsecurity.net/~spender/64bit_dos.c
execve()->copy_strings() can allocate a lot of memory, but
this is not visible to oom-killer, nobody can see the nascent
bprm->mm and take it into account.
With this patch get_arg_page() increments current's MM_ANONPAGES
counter every time we allocate the new page for argv/envp. When
do_execve() succeds or fails, we change this counter back.
Technically this is not 100% correct, we can't know if the new
page is swapped out and turn MM_ANONPAGES into MM_SWAPENTS, but
I don't think this really matters and everything becomes correct
once exec changes ->mm or fails.
Feng Tang [Fri, 19 Nov 2010 03:01:48 +0000 (11:01 +0800)]
serial: mfd: adjust the baud rate setting
Previous baud rate setting code only has been tested with 3.5M/9600/
115200/230400/460800 bps, and recently we got a 3M bps device to test,
which needs to modify current MUL register setting, and with this
patch 2.5M/2M/1.5M/1M/0.5M should also work as they just use a MUL
value scale down from 3M's.
Also got some reference register setting from silicon guys for
different baud rates, which tries to keep the pre-scalar register value
to 16.
Jeff Layton [Tue, 30 Nov 2010 20:14:48 +0000 (15:14 -0500)]
cifs: fix parsing of hostname in dfs referrals
The DFS referral parsing code does a memchr() call to find the '\\'
delimiter that separates the hostname in the referral UNC from the
sharename. It then uses that value to set the length of the hostname via
pointer subtraction. Instead of subtracting the start of the hostname
however, it subtracts the start of the UNC, which causes the code to
pass in a hostname length that is 2 bytes too long.
Reported-and-Tested-by: Robbert Kouprie <robbert@exx.nl> Signed-off-by: Jeff Layton <jlayton@redhat.com> Cc: Wang Lei <wang840925@gmail.com> Cc: David Howells <dhowells@redhat.com> Cc: stable@kernel.org Signed-off-by: Steve French <sfrench@us.ibm.com>
Alan Stern [Mon, 29 Nov 2010 15:17:22 +0000 (10:17 -0500)]
USB: fix autosuspend bug in usb-serial
This patch (as1437) fixes a bug in the usb-serial autosuspend
handling. Since the usb-serial core now has autosuspend support, it
must set the .supports_autosuspend member in every serial driver it
registers. Otherwise the usb_autopm_get_interface() call won't work.
This fixes Bugzilla #23012.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: stable@kernel.org Reported-by: Kevin Smith <thirdwiggin@gmail.com> Reported-and-tested-by: Simon Gerber <gesimu@gmail.com> Reported-and-tested-by: Matteo Croce <matteo@openwrt.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Tomoki Sekiyama [Mon, 22 Nov 2010 10:29:23 +0000 (19:29 +0900)]
USB: yurex: add .llseek fop to file_operations
Default llseek operation behavior was changed by the patch named
"vfs: make no_llseek the default" after the yurex driver had been merged,
so the llseek to yurex is now ignored.
This patch add llseek fop with default_llseek to yurex driver
to catch up to the change.
at91: Convert remaining boards to new-style UART initialization
Convert the following AT91RM9200-based boards to the new-style UART
initialization:
- Ajeco 1ARM Single Board Computer
- Sperry-Sun KAFA board
- picotux 200
Remove the deprecated at91_init_serial
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Andrew Victor <linux@maxim.org.za>
Randy Dunlap [Thu, 18 Nov 2010 23:02:26 +0000 (15:02 -0800)]
regulator: fix kernel-doc for set_consumer_device_supply
Fix kernel-doc warning for set_consumer_device_supply():
Warning(drivers/regulator/core.c:912): missing initial short description on line:
* set_consumer_device_supply: Bind a regulator to a symbolic supply
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Bengt Jonsson [Wed, 10 Nov 2010 10:06:22 +0000 (11:06 +0100)]
regulator: enable supply regulator only when use count is zero
Supply regulators are disabled only when the last
reference count is removed on the child regulator
(the use count goes from 1 to 0). This patch changes
the behaviour of enable so the supply regulator is
enabled only when the use count of the child
regulator goes from 0 to 1.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com> Acked-by: Linus Walleij <linus.walleij@stericsson.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Axel Lin [Fri, 22 Oct 2010 08:38:22 +0000 (16:38 +0800)]
regulator: twl-regulator - fix twlreg_set_mode
The Singular Message is 16 bits:
DEV_GRP[15:13] MT[12] RES_ID[11:4] RES_STATE[3:0]
Current implementation return immedially after sucessfuly write MSB part.
To properly set mode, we need to write the complete message ( MSB and LSB ).
In twl.h, now we have defines for PM Master module register offsets,
use it instead of hard coded 0x15/0x16.
Use "message & 0xff" to ensure we send correct value for LSB.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Tested-by: Lesly Arackal Manuel <leslyam@ti.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Axel Lin [Fri, 5 Nov 2010 07:27:17 +0000 (15:27 +0800)]
regulator: Return proper error for regulator_register()
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Axel Lin [Fri, 5 Nov 2010 13:51:32 +0000 (21:51 +0800)]
regulator: Ensure enough delay time for enabling regulator
Integer division will truncate the result, this patch ensures we have
enough delay time for enabling regulator.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Axel Lin [Fri, 5 Nov 2010 07:25:12 +0000 (15:25 +0800)]
regulator: Remove a redundant device_remove_file call in create_regulator
We already have device_remove_file() in error path,
no need to call it before goto link_name_err.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Mark Brown [Wed, 3 Nov 2010 04:08:04 +0000 (00:08 -0400)]
regulator: Staticise mc13783_powermisc_rmw()
It is not used outside this driver so no need to make the symbol global.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Alberto Panizzo <maramaopercheseimorto@gmail.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Mattias Wallin [Tue, 2 Nov 2010 13:55:34 +0000 (14:55 +0100)]
regulator: regulator disable supply fix
This patch fixes a disable failure when regulator supply is used.
A while loop in regulator disable checks for supply pointer != NULL
but the pointer is not always updated, resulting in the while loop
running too many times causing a disable failure.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com> Acked-by: Linus Walleij <linus.walleij@stericsson.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Dave Martin [Mon, 29 Nov 2010 18:43:29 +0000 (19:43 +0100)]
ARM: 6505/1: kprobes: Don't HAVE_KPROBES when CONFIG_THUMB2_KERNEL is selected
Currently, the kprobes implementation for ARM only supports the ARM
instruction set, so it only works if CONFIG_THUMB2_KERNEL is not
enabled.
Until kprobes is updated to work with Thumb-2, turning it on will
cause horrible things to happen, so this patch disables it for now.
Signed-off-by: Dave Martin <dave.martin@linaro.org> Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dave Martin [Tue, 30 Nov 2010 12:05:10 +0000 (13:05 +0100)]
ARM: 6508/1: vexpress: Correct data alignment in headsmp.S for CONFIG_THUMB2_KERNEL
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a
result, using these directives in code sections can result in
misaligned data words when building a Thumb-2 kernel
(CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to
assume that fundamental types of word size or above are word-
aligned when accessing them from C. If the data is not really
word-aligned, this can cause impaired performance and stray
alignment faults in some circumstances.
In general, the following rules should be applied when using
data word declaration directives inside code sections:
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Dave Martin <dave.martin@linaro.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dave Martin [Tue, 30 Nov 2010 12:04:36 +0000 (13:04 +0100)]
ARM: 6507/1: RealView: Correct data alignment in headsmp.S for CONFIG_THUMB2_KERNEL
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a result,
using these directives in code sections can result in misaligned data
words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to assume that
fundamental types of word size or above are word- aligned when
accessing them from C. If the data is not really word-aligned, this
can cause impaired performance and stray alignment faults in some
circumstances.
In general, the following rules should be applied when using data word
declaration directives inside code sections:
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Dave Martin <dave.martin@linaro.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dave Martin [Mon, 29 Nov 2010 18:43:28 +0000 (19:43 +0100)]
ARM: 6504/1: Thumb-2: Fix long-distance conditional branches in head.S for Thumb-2.
The 32-bit conditional branches in Thumb-2 have a shorter range
(+/-512K) than their ARM counterparts (+/-32MB). The linker does
not currently generate trampolines to extend the range of these
Thumb-2 conditional branches, resulting in link errors when vmlinux
is sufficiently large, e.g.:
head.o:(.text+0x464): relocation truncated to fit: R_ARM_THM_JUMP19
This patch forces the longer-range, unconditional branch encoding
by use of an explicit IT instruction. The resulting branches are
triggered on the same conditions as before.
Signed-off-by: Dave Martin <dave.martin@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dave Martin [Mon, 29 Nov 2010 18:43:27 +0000 (19:43 +0100)]
ARM: 6503/1: Thumb-2: Restore sensible zImage header layout for CONFIG_THUMB2_KERNEL
The code which makes up the zImage header intends to leave a
32-byte gap followed by a branch to the real entry point, a magic
number, and a word containing the absolute entry point address.
This gets messed up with with CONFIG_THUMB2_KERNEL, because the
size of the initial padding NOPs changes.
Instead, the header can be made fully compatible by restoring it to
ARM.
In the Thumb-2 case, we can replace the initial NOPs with a
sequence which switches to Thumb and jumps to the real entry point.
As a consequence, the zImage entry point is now always ARM, so no
special magic is needed any more for the uImage rules in the
Thumb-2 case.
Signed-off-by: Dave Martin <dave.martin@linaro.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dave Martin [Mon, 29 Nov 2010 18:43:26 +0000 (19:43 +0100)]
ARM: 6502/1: Thumb-2: Fix CONFIG_THUMB2_KERNEL breakage in compressed/head.S
Some instruction operand combinations are used here which are nor
permitted in Thumb-2.
In particular, most uses of pc as an operand are disallowed in
Thumb-2, and deprecated in ARM from ARMv7 onwards.
The modified code introduced by this patch should be compatible
with all architecture versions >= v3, with or without
CONFIG_THUMB2_KERNEL.
Reviewed-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Dave Martin <dave.martin@linaro.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dave Martin [Mon, 29 Nov 2010 18:43:25 +0000 (19:43 +0100)]
ARM: 6501/1: Thumb-2: Correct data alignment for CONFIG_THUMB2_KERNEL in mm/proc-v7.S
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a result,
using these directives in code sections can result in misaligned
data words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to assume
that fundamental types of word size or above are word- aligned when
accessing them from C. If the data is not really word-aligned,
this can cause impaired performance and stray alignment faults in
some circumstances.
In general, the following rules should be applied when using data
word declaration directives inside code sections:
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
In this specific case, we can achieve the desired alignment by
forcing a 32-bit branch instruction using the W() macro, since the
assembler location counter is already 32-bit aligned in this case.
Reviewed-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Dave Martin <dave.martin@linaro.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dave Martin [Mon, 29 Nov 2010 18:43:24 +0000 (19:43 +0100)]
ARM: 6500/1: Thumb-2: Correct data alignment for CONFIG_THUMB2_KERNEL in kernel/head.S
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a result,
using these directives in code sections can result in misaligned
data words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to assume
that fundamental types of word size or above are word- aligned when
accessing them from C. If the data is not really word-aligned,
this can cause impaired performance and stray alignment faults in
some circumstances.
In general, the following rules should be applied when using data
word declaration directives inside code sections:
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Dave Martin <dave.martin@linaro.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dave Martin [Mon, 29 Nov 2010 18:43:23 +0000 (19:43 +0100)]
ARM: 6499/1: Thumb-2: Correct data alignment for CONFIG_THUMB2_KERNEL in bootp/init.S
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a result,
using these directives in code sections can result in misaligned
data words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to assume
that fundamental types of word size or above are word- aligned when
accessing them from C. If the data is not really word-aligned,
this can cause impaired performance and stray alignment faults in
some circumstances.
In general, the following rules should be applied when using data
word declaration directives inside code sections:
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Dave Martin <dave.martin@linaro.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dave Martin [Mon, 29 Nov 2010 18:43:22 +0000 (19:43 +0100)]
ARM: 6498/1: vfp: Correct data alignment for CONFIG_THUMB2_KERNEL
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a result,
using these directives in code sections can result in misaligned
data words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to assume
that fundamental types of word size or above are word- aligned when
accessing them from C. If the data is not really word-aligned,
this can cause impaired performance and stray alignment faults in
some circumstances.
In general, the following rules should be applied when using data
word declaration directives inside code sections:
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Dave Martin <dave.martin@linaro.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dave Martin [Mon, 29 Nov 2010 18:43:21 +0000 (19:43 +0100)]
ARM: 6497/1: kexec: Correct data alignment for CONFIG_THUMB2_KERNEL
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a result,
using these directives in code sections can result in misaligned
data words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to assume
that fundamental types of word size or above are word- aligned when
accessing them from C. If the data is not really word-aligned,
this can cause impaired performance and stray alignment faults in
some circumstances.
In general, the following rules should be applied when using data
word declaration directives inside code sections:
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Dave Martin <dave.martin@linaro.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pawel Moll [Fri, 26 Nov 2010 12:45:43 +0000 (13:45 +0100)]
ARM: 6496/1: GIC: Do not try to register more then NR_IRQS interrupts
This change limits number of GIC-originating interrupts to the
platform maximum (defined by NR_IRQS) while still initialising
all distributor registers.
Signed-off-by: Pawel Moll <pawel.moll@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Daniel Glöckner [Tue, 30 Nov 2010 00:00:18 +0000 (01:00 +0100)]
s6105-ipcam: fix compilation
When the s6105-ipcam ASoC driver had been converted to the
multi-component API, a single reference to a former structure
element remained, blocking successful compilation.
Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Daniel Glöckner [Tue, 30 Nov 2010 00:00:17 +0000 (01:00 +0100)]
s6000-pcm: fix compilation
s6000_soc_platform has lost its forward declaration and there no
longer is a name element in it, so use a string constant when
calling request_irq.
Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Daniel Glöckner [Tue, 30 Nov 2010 00:00:16 +0000 (01:00 +0100)]
s6000-i2s: fix compilation
A semicolon was missing.
Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Mon, 29 Nov 2010 09:42:47 +0000 (17:42 +0800)]
ASoC: Fix missing spin_unlock_irqrestore
In nuc900_dma_hw_params(), if snd_pcm_lib_malloc_pages failed
it returns without calling spin_unlock_irqrestore().
Since snd_pcm_lib_malloc_pages() does not touch struct nuc900_audio,
we don't need to hold the lock while calling snd_pcm_lib_malloc_pages().
Fix it by moving spin_lock_irqsave() down to after snd_pcm_lib_malloc_pages().
In nuc900_dma_prepare(), spin_unlock_irqrestore() is missing in the error path.
Fix it by removing the return in default case.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Wan ZongShun <mcuos.com@gmail.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is required for the Sony Vaio Jesse was working on at the time, but
breaks most other eDP machines - machines that were working in earlier
kernels.
Reported-and-tested-by: Dave Airlie <airlied@redhat.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31188 Tested-by: Zhao Jian <jian.j.zhao@intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Takashi Iwai [Tue, 30 Nov 2010 07:14:21 +0000 (08:14 +0100)]
ALSA: Fix SNDCTL_DSP_RESET ioctl for OSS emulation
In OSS emulation, SNDCTL_DSP_RESET ioctl needs the reset of the internal
buffer state in addition to drop of the running streams. Otherwise the
succeeding access becomes inconsistent.
Tested-by: Amit Nagal <helloin.amit@gmail.com> Cc: <stable@kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Suresh Jayaraman [Wed, 24 Nov 2010 12:19:06 +0000 (17:49 +0530)]
cifs: enable fscache iff fsc mount option is used explicitly
Currently, if CONFIG_CIFS_FSCACHE is set, fscache is enabled on files opened
as read-only irrespective of the 'fsc' mount option. Fix this by enabling
fscache only if 'fsc' mount option is specified explicitly.
Remove an extraneous cFYI debug message and fix a typo while at it.
Reported-by: Jeff Layton <jlayton@redhat.com> Acked-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Suresh Jayaraman <sjayaraman@suse.de> Signed-off-by: Steve French <sfrench@us.ibm.com>
Suresh Jayaraman [Wed, 24 Nov 2010 12:19:05 +0000 (17:49 +0530)]
cifs: allow fsc mount option only if CONFIG_CIFS_FSCACHE is set
Currently, it is possible to specify 'fsc' mount option even if
CONFIG_CIFS_FSCACHE has not been set. The option is being ignored silently
while the user fscache functionality to work. Fix this by raising error when
the CONFIG option is not set.
Reported-by: Jeff Layton <jlayton@redhat.com> Reviewed-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Suresh Jayaraman <sjayaraman@suse.de> Signed-off-by: Steve French <sfrench@us.ibm.com>
Ian Campbell [Wed, 3 Nov 2010 15:32:21 +0000 (15:32 +0000)]
xen: x86/32: perform initial startup on initial_page_table
Only make swapper_pg_dir readonly and pinned when generic x86 architecture code
(which also starts on initial_page_table) switches to it. This helps ensure
that the generic setup paths work on Xen unmodified. In particular
clone_pgd_range writes directly to the destination pgd entries and is used to
initialise swapper_pg_dir so we need to ensure that it remains writeable until
the last possible moment during bring up.
This is complicated slightly by the need to avoid sharing kernel PMD entries
when running under Xen, therefore the Xen implementation must make a copy of
the kernel PMD (which is otherwise referred to by both intial_page_table and
swapper_pg_dir) before switching to swapper_pg_dir.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Cc: Borislav Petkov <bp@alien8.de> Cc: H. Peter Anvin <hpa@linux.intel.com> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
On-list discussion seems to suggest that the robustness fixes for printk
make this unnecessary and DaveM has also agreed in person at Kernel Summit
and on list.
The main problem with this code is once we hit a lockdep splat we always
keep oops_in_progress set, the console layer uses oops_in_progress with KMS
to decide when it should be showing the oops and not showing X, so it causes
problems around suspend/resume time when a userspace resume can cause a console
switch away from X, only if oops_in_progress is set (which is what we want
if an oops actually is in progress, but not because we had a lockdep splat
2 days prior).
Cc: David S Miller <davem@davemloft.net> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>