Andre Guedes [Fri, 4 Nov 2011 17:16:53 +0000 (14:16 -0300)]
Bluetooth: Periodic Inquiry and Discovery
By using periodic inquiry command we're not able to detect correctly
when the controller has started inquiry.
Today we have this workaround in inquiry result event handler
to set the HCI_INQUIRY flag when it sees the first inquiry result
event. This workaround isn't enough because the device may be
performing an inquiry but the HCI_INQUIRY flag is not set. For
instance, if there is no device in range, no inquiry result event
is generated, consequently, the HCI_INQUIRY flags isn't set when
it should so.
We rely on HCI_INQUIRY flag to implement the discovery procedure
properly. So, as we aren't able to clear/set the HCI_INQUIRY flag
in a reliable manner, periodic inquiry events shouldn't change
the HCI_INQUIRY flag.
Thus, due to that issue and in order to keep compatibility with
userspace, periodic inquiry events shouldn't send mgmt discovering
events.
In future, we might track if periodic inquiry is enabled or not.
By tracking this state we'll be able to do some improvements in
Discovery such as failing MGMT_OP_START_DISCOVERY command in case
periodic inquiry is on. We can also send no mgmt_device_found
event if periodic inquiry is on.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Andre Guedes [Fri, 4 Nov 2011 17:16:52 +0000 (14:16 -0300)]
Bluetooth: Create hci_cancel_inquiry()
This patch adds a function to hci_core to cancel an ongoing inquiry.
According to the Bluetooth spec, the inquiry cancel command should
only be issued after the inquiry command has been issued, a command
status event has been received for the inquiry command, and before
the inquiry complete event occurs.
As HCI_INQUIRY flag is only set just after an inquiry command status
event occurs and it is cleared just after an inquiry complete event
occurs, the inquiry cancel command should be issued only if HCI_INQUIRY
flag is set.
Additionally, cancel inquiry related code from stop_discovery() were
replaced by a hci_cancel_inquiry() call.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Add parsing Extended Flow Specification in L2CAP Config Response.
Based upon haijun.liu <haijun.liu@atheros.com> series of patches
(sent Sun, 22 Aug 2010)
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Johan Hedberg [Thu, 3 Nov 2011 22:17:45 +0000 (00:17 +0200)]
Bluetooth: Clean up logic in hci_cc_write_scan_enable
This patch adds a new label to hci_cc_write_scan_enable to avoid
unnecessary indentation. This will be convenient especially when new
code for the discoverable timeout gets added.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Mat Martineau [Wed, 2 Nov 2011 23:18:35 +0000 (16:18 -0700)]
Bluetooth: Add signal handlers for channel moves
AMP channels can be moved between BR/EDR and AMP controllers using a
sequence of signals. Every attempted channel move involves a series of
four signals:
Mat Martineau [Wed, 2 Nov 2011 23:18:31 +0000 (16:18 -0700)]
Bluetooth: Add AMP-related data and structures for channel signals
AMP channel creation and channel moves are coordinated using the L2CAP
signaling channel. These definitions cover the "create channel",
"move channel", and "move channel confirm" signals.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org> Acked-by: Marcel Holtmann <marcel@holtmann.org> Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Mat Martineau [Wed, 2 Nov 2011 23:18:28 +0000 (16:18 -0700)]
Bluetooth: Add BT_CHANNEL_POLICY socket option
Allow control of AMP functionality on L2CAP sockets. By default,
connections will be restricted to BR/EDR. Manipulating the
BT_CHANNEL_POLICY option allows for channels to be moved to or created
on AMP controllers.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org> Acked-by: Marcel Holtmann <marcel@holtmann.org> Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth: use buffer priority to mark URB_ISO_ASAP flag
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth: recalculate priorities when channels are starving
To avoid starvation the priority is recalculated so that the starving
channels are promoted to HCI_PRIO_MAX - 1 (6).
HCI_PRIO_MAX (7) is considered special, because it requires CAP_NET_ADMIN
capability which can be used to provide more guaranties, so it is not used
when promoting.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The quote is calculated based on the first buffer in the queue so if the
priority changes to something lower than the priority of the first skb
the quote needs to be recalculated.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This implement priority based scheduler using skbuffer priority set via
SO_PRIORITY socket option.
It introduces hci_chan_hash (list of HCI Channel/hci_chan) per connection,
each item in this list refer to a L2CAP connection and it is used to
queue the data for transmission.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
David Herrmann [Tue, 1 Nov 2011 16:27:50 +0000 (17:27 +0100)]
Bluetooth: hidp: Fix module reference cleanup
Calling module_put(THIS_MODULE) is *never* safe when we cannot go sure that we
own at least two references. This is because the call may unload our module
before it returns and then the "return" will jump into invalid memory.
Gladly, module.h provides a wrapper for kthread-users: module_put_and_exit().
This puts our module and then exits the kthread without returning to the module.
This patch fixes the hidp kthread to use this wrapper instead of manually
freeing its own reference. See nfsd or lockd for other kthreads using this.
Calling __module_get() inside the kthread is safe as the hidp module will always
wait until the kthread sets "waiting_for_startup" to 0.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
David Herrmann [Wed, 26 Oct 2011 09:22:46 +0000 (11:22 +0200)]
Bluetooth: bfusb: Fix error path on firmware load
When loading the usb-configuration we do not signal the end of configuration on
memory allocation error. This patch moves the memory allocation to the top so
every error path uses "goto error" now to correctly send the usb-ctrl message
when detecting some error.
This also replaces GFP_ATOMIC with GFP_KERNEL as we are allowed to sleep here.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
David Herrmann [Tue, 25 Oct 2011 19:13:36 +0000 (21:13 +0200)]
Bluetooth: bcm203x: Use GFP_KERNEL in workqueue
A workqueue is allowed to sleep so we can safely use GFP_KERNEL instead of
GFP_ATOMIC. This is still legacy code when the driver used timer BHs and not a
worqueue.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
David Herrmann [Wed, 26 Oct 2011 09:13:13 +0000 (11:13 +0200)]
Bluetooth: bcm203x: Fix race condition on disconnect
When disconnecting a bcm203x device we kill and destroy the usb-urb, however,
there might still be a pending work-structure which resubmits the now invalid
urb. To avoid this race condition, we simply set a shutdown-flag and
synchronously kill the worker first.
This also adds a comment to all schedule_work()s, as it is really not clear
that they are used as replacement for short timers (which can be seen in the git
history).
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
David Herrmann [Tue, 25 Oct 2011 10:09:52 +0000 (12:09 +0200)]
Bluetooth: ath3k: Use GFP_KERNEL instead of GFP_ATOMIC
We are allowed to sleep here so no need to use GFP_ATOMIC. The caller
(ath3k_probe) calls request_firmware() which definitely sleeps. Hence, we should
avoid using GFP_ATOMIC.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Johan Hedberg [Mon, 24 Oct 2011 20:36:26 +0000 (22:36 +0200)]
Bluetooth: Set HCI_MGMT flag only in read_controller_info
The HCI_MGMT flag should only be set when user space requests the full
controller information. This way we avoid potential issues with setting
change events ariving before the actual read_controller_info command
finishes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Szymon Janc [Mon, 17 Oct 2011 21:05:49 +0000 (23:05 +0200)]
Bluetooth: Increase HCI reset timeout in hci_dev_do_close
I've noticed that my CSR usb dongle was not working if it was plugged in when
PC was booting. It looks like I get two HCI reset command complete events (see
hcidump logs below).
The root cause is reset called from off_timer. Timeout for this reset to
complete is set to 250ms and my bt dongle requires more time for replying with
command complete event. After that, chip seems to reply with reset command
complete event for next non-reset command.
Attached patch increase mentioned timeout to HCI_INIT_TIMEOUT, this value is
already used for timeouting hci_reset_req in hci_dev_reset().
This might also be related to BT not working after suspend that was reported
here some time ago.
Hcidump log:
2011-09-12 23:13:27.379465 < HCI Command: Reset (0x03|0x0003) plen 0
2011-09-12 23:13:27.380797 > HCI Event: Command Complete (0x0e) plen 4
Reset (0x03|0x0003) ncmd 1
status 0x00
2011-09-12 23:13:27.380859 < HCI Command: Read Local Supported Features (0x04|0x000
3) plen 0
2011-09-12 23:13:27.760789 > HCI Event: Command Complete (0x0e) plen 4
Reset (0x03|0x0003) ncmd 1
status 0x00
2011-09-12 23:13:27.760831 < HCI Command: Read Local Version Information (0x04|0x00
01) plen 0
2011-09-12 23:13:27.764780 > HCI Event: Command Complete (0x0e) plen 12
Read Local Version Information (0x04|0x0001) ncmd 1
status 0x00
HCI Version: 1.1 (0x1) HCI Revision: 0x36f
LMP Version: 1.1 (0x1) LMP Subversion: 0x36f
Manufacturer: Cambridge Silicon Radio (10)
Signed-off-by: Szymon Janc <szymon@janc.net.pl> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth: rfcomm: Fix sleep in invalid context in rfcomm_security_cfm
This was triggered by turning off encryption on ACL link when rfcomm
was using high security. rfcomm_security_cfm (which is called from rx
task) was closing DLC and this involves sending disconnect message
(and locking socket).
Move closing DLC to rfcomm_process_dlcs and only flag DLC for closure
in rfcomm_security_cfm.
BUG: sleeping function called from invalid context at net/core/sock.c:2032
in_atomic(): 1, irqs_disabled(): 0, pid: 1788, name: kworker/0:3
[<c0068a08>] (unwind_backtrace+0x0/0x108) from [<c05e25dc>] (dump_stack+0x20/0x24)
[<c05e25dc>] (dump_stack+0x20/0x24) from [<c0087ba8>] (__might_sleep+0x110/0x12c)
[<c0087ba8>] (__might_sleep+0x110/0x12c) from [<c04801d8>] (lock_sock_nested+0x2c/0x64)
[<c04801d8>] (lock_sock_nested+0x2c/0x64) from [<c05670c8>] (l2cap_sock_sendmsg+0x58/0xcc)
[<c05670c8>] (l2cap_sock_sendmsg+0x58/0xcc) from [<c047cf6c>] (sock_sendmsg+0xb0/0xd0)
[<c047cf6c>] (sock_sendmsg+0xb0/0xd0) from [<c047cfc8>] (kernel_sendmsg+0x3c/0x44)
[<c047cfc8>] (kernel_sendmsg+0x3c/0x44) from [<c056b0e8>] (rfcomm_send_frame+0x50/0x58)
[<c056b0e8>] (rfcomm_send_frame+0x50/0x58) from [<c056b168>] (rfcomm_send_disc+0x78/0x80)
[<c056b168>] (rfcomm_send_disc+0x78/0x80) from [<c056b9f4>] (__rfcomm_dlc_close+0x2d0/0x2fc)
[<c056b9f4>] (__rfcomm_dlc_close+0x2d0/0x2fc) from [<c056bbac>] (rfcomm_security_cfm+0x140/0x1e0)
[<c056bbac>] (rfcomm_security_cfm+0x140/0x1e0) from [<c0555ec0>] (hci_event_packet+0x1ce8/0x4d84)
[<c0555ec0>] (hci_event_packet+0x1ce8/0x4d84) from [<c0550380>] (hci_rx_task+0x1d0/0x2d0)
[<c0550380>] (hci_rx_task+0x1d0/0x2d0) from [<c009ee04>] (tasklet_action+0x138/0x1e4)
[<c009ee04>] (tasklet_action+0x138/0x1e4) from [<c009f21c>] (__do_softirq+0xcc/0x274)
[<c009f21c>] (__do_softirq+0xcc/0x274) from [<c009f6c0>] (do_softirq+0x60/0x6c)
[<c009f6c0>] (do_softirq+0x60/0x6c) from [<c009f794>] (local_bh_enable_ip+0xc8/0xd4)
[<c009f794>] (local_bh_enable_ip+0xc8/0xd4) from [<c05e5804>] (_raw_spin_unlock_bh+0x48/0x4c)
[<c05e5804>] (_raw_spin_unlock_bh+0x48/0x4c) from [<c040d470>] (data_from_chip+0xf4/0xaec)
[<c040d470>] (data_from_chip+0xf4/0xaec) from [<c04136c0>] (send_skb_to_core+0x40/0x178)
[<c04136c0>] (send_skb_to_core+0x40/0x178) from [<c04139f4>] (cg2900_hu_receive+0x15c/0x2d0)
[<c04139f4>] (cg2900_hu_receive+0x15c/0x2d0) from [<c0414cb8>] (hci_uart_tty_receive+0x74/0xa0)
[<c0414cb8>] (hci_uart_tty_receive+0x74/0xa0) from [<c02cbd9c>] (flush_to_ldisc+0x188/0x198)
[<c02cbd9c>] (flush_to_ldisc+0x188/0x198) from [<c00b2774>] (process_one_work+0x144/0x4b8)
[<c00b2774>] (process_one_work+0x144/0x4b8) from [<c00b2e8c>] (worker_thread+0x198/0x468)
[<c00b2e8c>] (worker_thread+0x198/0x468) from [<c00b9bc8>] (kthread+0x98/0xa0)
[<c00b9bc8>] (kthread+0x98/0xa0) from [<c0061744>] (kernel_thread_exit+0x0/0x8)
Signed-off-by: Szymon Janc <szymon.janc@tieto.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Johan Hedberg [Tue, 1 Nov 2011 15:06:44 +0000 (17:06 +0200)]
Bluetooth: Fix command complete/status for discovery commands
This patch adds the necessary code to send proper command status or
command complete events to the start/stop discovery management commands.
Before this patch these events were completely missing.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
David Herrmann [Wed, 26 Oct 2011 08:43:18 +0000 (10:43 +0200)]
Bluetooth: Ignore hci_unregister_dev return value
Make all bluetooth drivers ignore the return value of hci_unregister_dev as it
always returns 0. In the next step, hci_unregister_dev can be modified to return
void.
Some of the drivers already ignore the return value (including btusb), hence,
this will increase consitency in the bluetooth drivers.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Add parsing Extended Flow Specification option in L2CAP Config Request
Based upon haijun.liu <haijun.liu@atheros.com> series of patches
(sent Sun, 22 Aug 2010)
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
There are three different Control Field formats: the Standard Control
Field, the Enhanced Control Field, and the Extended Control Field.
Patch adds function to handle all those fields seamlessly.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
David Herrmann [Sat, 8 Oct 2011 12:58:48 +0000 (14:58 +0200)]
Bluetooth: Rename sysfs un/register to add/del
As we introduced hci_init_sysfs() we should also rename
hci_register_sysfs() and hci_unregister_sysfs() to hci_add_sysfs() and
hci_del_sysfs() like we do with hci_conn_add/del_sysfs(). It looks more
consistent now.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
David Herrmann [Sat, 8 Oct 2011 12:58:47 +0000 (14:58 +0200)]
Bluetooth: Fix hci core device initialization
We must not call device_del() if we didn't use device_add(). See module.c
for comments on that. Therefore, we need to call device_initialize() when
allocating the hci device and later device_add() instead of
device_register().
This also fixes a bug when hci_register_dev() failed and we call
hci_free_dev() without a valid core device. hci_free_dev() segfaults while
calling put_device() on invalid memory.
We already do this with hci_conn connections (hci_conn_init_sysfs()) so
they do not need to be fixed.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Add Extended Flow Specification option when building L2CAP
Configuration Request. EFS is added if both the local and
remote L2CAP entities have indicated support for the
Extended Flow Specification for BR/EDR.
Define Extended Flow Specification structures and default values.
Based upon haijun.liu <haijun.liu@atheros.com> series of patches
(sent Sun, 22 Aug 2010)
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Segmentation and Reassembly (SAR) occupies different windows in standard and
extended control fields. Convert hardcoded masks to relative ones and use shift
to access SAR bits.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth: EWS: rewrite handling Supervisory (S) bits
Supervisory bits occupy different windows in standard / extended control
fields. Convert hardcoded masks to relative ones and use shift to access
S-bit window.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth: EWS: extended window size option support
Adds support for extended window size (EWS) config option. We enable EWS
feature in L2CAP Info RSP when hs enabled. EWS option is included in L2CAP
Config Req if tx_win (which is set via socket) bigger then standard default
value (63) && hs enabled && remote side supports EWS feature.
Using EWS selects extended control field in L2CAP.
Code partly based on Qualcomm and Atheros patches sent upstream a year ago.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Paul Bolle [Sun, 9 Oct 2011 10:12:22 +0000 (12:12 +0200)]
Bluetooth: btusb: hide more usb_submit_urb errors
There are still three calls of usb_submit_urb() that will print errors
if those calls return -EPERM or -ENODEV. I have never triggered these,
so I'm not sure when these return values might be seen. It still makes
sense to be silent if these occur (since "urb is being killed" and
"device got disconnected" aren't things to worry about).
Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Paul Bolle [Sun, 9 Oct 2011 10:12:16 +0000 (12:12 +0200)]
Bluetooth: btusb: also be quiet when suspending
usb_submit_urb() returns -ENODEV when a usb device is disconnected. In
commit 4935f1c164ac528dff3538f97953b385ba500710 ("Bluetooth: btusb: be
quiet on device disconnect") I stopped treating that return as an error
in the three btusb_*_complete() functions.
It turns out btusb_send_frame() generates a similar error if the system
is suspended while the bluetooth usb device is enabled. The sensible
thing to do here seems to be to treat -ENODEV (and -EPERM) just like the
btusb_*_complete() functions now do.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Peter Hurley [Tue, 30 Aug 2011 15:53:35 +0000 (11:53 -0400)]
Bluetooth: hidp: safely acquire hci connection
Claim device lock to safely enumerate hci connection list and bump
hci connection proxy device ref count simultaneously.
This patch incorporates David Herrmann's fix to prevent adding an
HID device when the hci connection no longer exists.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
David Herrmann [Fri, 26 Aug 2011 12:06:02 +0000 (14:06 +0200)]
Bluetooth: hidp: Stop I/O on shutdown
Current hidp driver purges the in/out queue on HID shutdown, but does
not prevent further I/O. If a driver uses hidp_output_raw_report or
hidp_get_raw_report during shutdown, the driver hangs for 5 or 10
seconds per call until it gets a timeout.
That is, if the output queue of an HID driver has 10 messages pending,
it will take 50s until hid_destroy_device() will return. The
hidp_session_sem semaphore is held during shutdown so no other HID
device may be added/removed during this time.
This patch makes hidp_output_raw_report and hidp_get_raw_report fail if
session->terminate is true. Also hidp_session will wakeup all current
calls to these functions to cancel the current operations.
We already purge the current I/O queues on hidp_stop(), so this data loss
does not change the behaviour of the HID drivers.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Andre Guedes [Mon, 26 Sep 2011 23:48:35 +0000 (20:48 -0300)]
Bluetooth: hci_le_adv_report_evt code refactoring
There is no reason to treat the first advertising entry differently
from the potential other ones. Besides, the current implementation
can easily leads to typos.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Checking conn->pending_sec_level if there is no connection leads to potential
null pointer dereference. Don't process pin_code_request_event at all if no
connection exists.
Anderson Lizardo [Wed, 27 Jul 2011 21:40:09 +0000 (18:40 -0300)]
Bluetooth: use recommended LE connection parameters
The new connection parameters now match the recommended values for
Proximity and Health Thermometer profiles. The previous values were
ramdomly chosen, and are either too low or too high for most cases.
New values:
Scan Interval: 60 ms
Scan Window: 30 ms
Minimum Connection Interval: 50 ms
Maximum Connection Interval: 70 ms
Supervision Timeout: 420 ms
See "Table 5.2: Recommended Scan Interval and Scan Window Values" and
"Table 5.3: Recommended Connection Interval Values" for both profiles
for details. Note that the "fast connection" parameters were chosen,
because we do not support yet dynamically changing these parameters from
initiator side.
Additionally, the Proximity profile recommends (section "4.4 Alert on
Link Loss"):
"It is recommended that the Link Supervision Timeout (LSTO) is set to 6x
the connection interval."
Minimum_CE_Length and Maximum_CE_Length were also changed from 0x0001 to
0x0000 because they are informational and optional, and old value was
not reflecting reality.
Signed-off-by: Anderson Lizardo <anderson.lizardo@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Mat Martineau [Fri, 22 Jul 2011 21:53:59 +0000 (14:53 -0700)]
Bluetooth: Handle fragmented skbs in bt_sock_stream_recvmsg()
ERTM reassembly will be more efficient when skbs are linked together
rather than copying every incoming data byte. The existing stream recv
function assumes skbs are linear, so it needs to know how to handle
fragments before reassembly is changed.
Mat Martineau [Fri, 22 Jul 2011 21:53:58 +0000 (14:53 -0700)]
Bluetooth: Linearize skbs for use in BNEP, CMTP, HIDP, and RFCOMM
Fragmented skbs are only encountered when receiving ERTM or streaming
mode L2CAP data. BNEP, CMTP, HIDP, and RFCOMM generally use basic
mode, but they need to handle fragments without crashing.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
projects / karo-tx-linux.git / log